Xerox 7120 ошибка 092 314

Xerox error 092 315

КОНФЕРЕНЦИЯ СТАРТКОПИ
Принтеры, копировальные аппараты, МФУ, факсы и другая офисная техника:
вопросы ремонта, обслуживания, заправки, выбора

Добрый день, данный аппарат может напечатать 1-2 листа и вываливается в ошибку 092-315.
Драм весь перебирал, шнек подачи тонера вычистил, тонер тубу также заменил (принтер госконторы, заправляли не понятно чем (тендер) поэтому сразу заменил тубу.) пока безрезультатно.

Инфа по поиску (переведено с буржуйского)
«Чтобы очистить его, очистите значение местоположения NVM [752-022] (средняя ошибка ATC) или местоположение NVM [752-023] (сбой амплитуды ATC ) до «0» ( чтение / запись NVM ).»

а что там очищать не совсем понял, буду признателен за любую информацию.

Вероятно судя по описанию от Вас требуется зайти в nvm rw и в hain link 752-023 и выставить там значение 0. А так. На ровном месте она возникнуть не могла. Тестом компонентов проверьте все ли там у Вас вращается как надо и подается ли тонер куда надо.

Да все вращается уже было проверено, компоненты также все прозванивал. а как зайти в nvm rw и в hain link 752-023 ?

(2)полагаю как обычно. Через ce mode.

Все-таки скорее всего было дело в тонере, сперва распечатал отчеты (есть с полной заливкой) несколько листов и после этого заработал, видать выгнал остатки старого тонера.
Сейчас уже 3 пачка бумаги распечатал. для уверенности пару раз выключал сабж.

Кстати тубу поставил от Xerox 3610 с заменой чипа, одинаковы.

Да у них одна архитектура. Печки тоже очень похожи.
(4) так в нем и было. Вопрос что. Но датчику тонера это явно не понравилось.

Источник

Xerox error 092 315

КОНФЕРЕНЦИЯ СТАРТКОПИ
Принтеры, копировальные аппараты, МФУ, факсы и другая офисная техника:
вопросы ремонта, обслуживания, заправки, выбора

Всем доброго времени суток ! Проблема с МФУ XEROX WC 5325 — после печати или копирования 4-5 листов блокируется и выдаёт ошибку 092-315 . Состояние сбрасывается путём отключения питания МФУ. После включения питания нормально выходит на готовность и после печати или копирования нескольких листов всё повторяется . Подскажите , если кто сталкивался с такой бедой , с чем это связано и как лечить . Или самый лучший вариант — где можно почитать сервисмануал . Заранее всем спасибо .

092-315 ATC Fail
The frequency at which the ATC Average Fail or the ATC Amplitude Fail has been occurring has exceeded the threshold value.
NOTE: Although this Fault can be cleared by turning the power OFF and ON and it will be possible to output a few sheets of printouts, when this Fault has occurred a certain number of times, it will no longer be clearable by turning the power OFF and ON. To clear it, clear the value of NVM location [752-022] (ATC Average Fail) or NVM location [752-023] (ATC Amplitude Fail) to «0» (NVM Read/Write). If the machine is not repaired back to normal status, this Fault will occur again during the operation.
— When turning the power OFF, turn OFF the power switch first and then the main power switch.
Check the following:
— The connection between the MCU PWB P/J413 and the Xero/Developer Cartridge P/J615 for open circuit, short circuit, and poor contact
— The Toner Dispense Motor for revolution failure: Component Control [093-002]
— The Toner Cartridge for internal toner blockage
If no problems are found, replace the following parts in sequence:
— Drum Cartridge
— MCU PWB

Спасибо , почти всё понятно

3. sahrikov1945 24.12.15 22:02

Источник

Thread: Advice Needed: Workcentre 7120 / System Error 092-315 on main display

Thread Tools

Display

Senior Tech 100+ Posts

Join Date Feb 2011 Location West Palm Beach, Fl. Posts 247 Rep Power 30

Advice Needed: Workcentre 7120 / System Error 092-315 on main display

I am getting a system error 092-315 on the main display on startup. Which indicates a ATC Fail (K) Black.

The error codes list states the following 092-315, 092-660, 092-668.

Upon inspection of the drum unit I found the (K) Black toner exit hole packed to the brim with toner
and piling up on top of the back of the drum. I looked at the other drum units (M,C,Y) and found no excess toner.

After vacuuming and cleaning the (K) Black drum unit area as bets as possible, and resetting NVRAM
752-368 (was at 1 reset to zero) 752-372 (was at 3 reset to zero).
Turned machine off (Top Power Button first then inside cover button next) Machine upon starting up printed several blank pages, then there was a metal clink sound and the 092-315 system error redisplayed itself on main screen.

I have determined that one of the following is at fault:
Main Drive Assembly – 007K16710
Dispense Motor -127K61161
Developer Clutch – 121K46371
Drum Drive Motor – 127K61161

Since this a time and materials call, was just looking for opinions on which one of the above would
be most likely to try first?

All help is appreciated, and thanks in advance

Re: Advice Needed: Workcentre 7120 / System Error 092-315 on main display

I am getting a system error 092-315 on the main display on startup. Which indicates a ATC Fail (K) Black.

The error codes list states the following 092-315, 092-660, 092-668.

Upon inspection of the drum unit I found the (K) Black toner exit hole packed to the brim with toner
and piling up on top of the back of the drum. I looked at the other drum units (M,C,Y) and found no excess toner.

After vacuuming and cleaning the (K) Black drum unit area as bets as possible, and resetting NVRAM
752-368 (was at 1 reset to zero) 752-372 (was at 3 reset to zero).
Turned machine off (Top Power Button first then inside cover button next) Machine upon starting up printed several blank pages, then there was a metal clink sound and the 092-315 system error redisplayed itself on main screen.

I have determined that one of the following is at fault:
Main Drive Assembly – 007K16710
Dispense Motor -127K61161
Developer Clutch – 121K46371
Drum Drive Motor – 127K61161

Since this a time and materials call, was just looking for opinions on which one of the above would
be most likely to try first?

All help is appreciated, and thanks in advance

Hello Can you check the following.
Check the following:

• The connection between the MCU PWB P/J411 and the CRUM Reader (K) P/J123 for open circuit, short circuit, and poor contact
• The connection terminals between the Drum Cartridge (K) CRUM PWB and the CRUM Reader (K) for damage and foreign substances
• The Toner Dispense Motor (C,K) for revolution failure: Component Control [093-004] ( PL 5.1)
• The Drum/IBT Drive Motor for revolution failure: Component Control [042-001] ( PL 3.2)
• The Main Drive Motor for revolution failure: Component Control [042-006] ( PL 3.3)
• The Dev K Clutch for failure: Component Control [042-010] ( PL 3.3)
• The path from Toner Cartridge (K) to Developer (K) for toner blockage
• The Developer (K) for internal toner blockage
• The Toner Cartridge (K) for internal toner blockage

If no problems are found, replace the following parts in sequence:

Источник

How to Fix 092-312 to 092-315 092-657 to 092-668 Error Code for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?

Posted by Xwk Tech on Dec 03, 2019

092-312 to 315, 092-657 to 660, 092-665 to 668 ATC Sensor Fault RAP

BSD-ON: BSD 9.5 Development (2 of 2)

092-312 Toner density in the developer unit as detected by the yellow ATC sensor abnormal. This fault occurs when the difference between the maximum and minimum values in the ATC sensor measurement set is lower than the threshold value.
092-313 Toner density in the developer unit as detected by the magenta ATC sensor abnormal. This fault occurs when the difference between the maximum and minimum values in the ATC sensor measurement set is lower than the threshold value.
092-314 Toner density in the developer unit as detected by the cyan ATC sensor abnormal. This fault occurs when the difference between the maximum and minimum values in the ATC sensor measurement set is lower than the threshold value.
092-315 Toner density in the developer unit as detected by the black ATC sensor abnormal. This fault occurs when the difference between the maximum and minimum values in the ATC sensor measurement set is lower than the threshold value.
092-657 Toner density in the developer unit as detected by the yellow ATC sensor abnormal. This fault occurs when the difference between the maximum and minimum values in the ATC sensor measurement set is lower than the threshold value.
092-658 Toner density in the developer unit as detected by the magenta ATC sensor abnormal. This fault occurs when the difference between the maximum and minimum values in the ATC sensor measurement set is lower than the threshold value.
092-659 Toner density in the developer unit as detected by the cyan ATC sensor abnormal. This fault occurs when the difference between the maximum and minimum values in the ATC sensor measurement set is lower than the threshold value.
092-660 Toner density in the developer unit as detected by the black ATC sensor abnormal. This fault occurs when the difference between the maximum and minimum values in the ATC sensor measurement set is lower than the threshold value.
092-665 Toner density in the developer unit as detected by the yellow ATC sensor abnormal. This fault occurs when the average value of the ATC sensor measurement values is not between the upper and lower limit values.
092-666 Toner density in the developer unit as detected by the magenta ATC sensor abnormal. This fault occurs when the average value of the ATC sensor measurement values is not between the upper and lower limit values.
092-667 Toner density in the developer unit as detected by the cyan ATC sensor abnormal. This fault occurs when the average value of the ATC sensor measurement values is not between the upper and lower limit values.
092-668 Toner density in the developer unit as detected by the black ATC sensor abnormal. This fault occurs when the average value of the ATC sensor measurement values is not between the upper and lower limit values.

Initial Actions

• Perform IQ1 to check for a blank page image quality defect.
• Enter dC125. Check for the below faults and perform the applicable procedures as necessary:

– 024-923 to 024-925 Y/M/C Toner Cartridge Empty RAP
– 093-912 Black Toner Cartridge Empty RAP

Procedure

WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.

NOTE: When this fault occurs, toner density control, by the ATC sensor, is not performed and ICDC (pixels) based toner supply control is performed instead. If the fault remains for a long time, image density error (too dark or too light) may occur.

Perform the steps that follow:

1. Switch off, then switch on the machine, GP 10.
2. Check the wiring between the applicable ATC sensor, yellow ( P/J120), magenta ( P/J119), cyan ( P/J118), black ( P/J117) and the drive PWB ( P/J414) for an open circuit, short circuit or damage.
3. If the fault persists , replace a new cartridge CRUM ( toner chip or drum chip ) listed as below or install new components as necessary:

– Black drum cartridge, PL 90.20 Item 5.
– Yellow drum cartridge, PL 90.20 Item 8.
– Magenta drum cartridge, PL 90.20 Item 7.
– Cyan drum cartridge, PL 90.20 Item 6.

– Black toner cartridge, PL 90.05 Item 13.
– Yellow toner cartridge, PL 90.05 Item 10.
– Magenta toner cartridge, PL 90.05 Item 11.
– Cyan toner cartridge, PL 90.05 Item 12.

• Drive PWB, PL 1.10 Item 4.
• ESS PWB, PL 3.10 Item 6.
• HVPS, PL 1.05 Item 7.

**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner’s property.**

You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.

Toner Chip (For North America and West Europe Region):

Toner Chip (For South America and East Europe Region):

Toner Chip (For Metered Machine):

Источник

Thread: Xerox wc 7125 error

Thread Tools

Display

Xerox wc 7125 error

The error is 092-315 any one have ideas. Also does any one have a service manual. sigh

Re: Xerox wc 7125 error

Description

The frequency at which the ATC Average Fail [K] or the ATC Amplitude Fail [K] has been occurring has exceeded the threshold value.
NOTE:

• Although this Fault can be cleared by turning the power OFF and ON and it will be possible to output a few sheets of printouts, when this Fault has occurred a certain number of times, it will no longer be clearable by turning the power OFF and ON. To clear it, clear the value of NVM location [752-368] (ATC Fail [K]) or NVM location[752-372] (ATC Fail Continuous Count [K]) to «0». If the machine is not repaired back to normal status, this Fault will occur again during the operation.
• When turning the power OFF, turn OFF the power switch first and then the main power switch.

Procedure

Check the following:

• The connection between the MCU PWB P/J411 and the CRUM Reader (K) P/J123 for open circuit, short circuit, and poor contact
• The connection terminals between the Drum Cartridge (K) CRUM PWB and the CRUM Reader (K) for damage and foreign substances
• The Toner Dispense Motor (C,K) for revolution failure: Component Control [093-004] ( PL 5.1)
• The Drum/IBT Drive Motor for revolution failure: Component Control [042-001] ( PL 3.2)
• The Main Drive Motor for revolution failure: Component Control [042-006] ( PL 3.3)
• The Dev K Clutch for failure: Component Control [042-010] ( PL 3.3)
• The path from Toner Cartridge (K) to Developer (K) for toner blockage
• The Developer (K) for internal toner blockage
• The Toner Cartridge (K) for internal toner blockage

If no problems are found, replace the following parts in sequence:

Service Manager 1,000+ Posts

Join Date Nov 2007 Location Somewhere in Europe near Black Sea Posts 2,038 Rep Power 60

Re: Xerox wc 7125 error

Problem with readings from ATC sensor for K.
Check K toner transport, K dispenser motor, K toner cartridge and developer for blockage, developer K clutch.

Re: Xerox wc 7125 error

Description

The frequency at which the ATC Average Fail [K] or the ATC Amplitude Fail [K] has been occurring has exceeded the threshold value.
NOTE:

• Although this Fault can be cleared by turning the power OFF and ON and it will be possible to output a few sheets of printouts, when this Fault has occurred a certain number of times, it will no longer be clearable by turning the power OFF and ON. To clear it, clear the value of NVM location [752-368] (ATC Fail [K]) or NVM location[752-372] (ATC Fail Continuous Count [K]) to «0». If the machine is not repaired back to normal status, this Fault will occur again during the operation.
• When turning the power OFF, turn OFF the power switch first and then the main power switch.

Procedure

Check the following:

• The connection between the MCU PWB P/J411 and the CRUM Reader (K) P/J123 for open circuit, short circuit, and poor contact
• The connection terminals between the Drum Cartridge (K) CRUM PWB and the CRUM Reader (K) for damage and foreign substances
• The Toner Dispense Motor (C,K) for revolution failure: Component Control [093-004] ( PL 5.1)
• The Drum/IBT Drive Motor for revolution failure: Component Control [042-001] ( PL 3.2)
• The Main Drive Motor for revolution failure: Component Control [042-006] ( PL 3.3)
• The Dev K Clutch for failure: Component Control [042-010] ( PL 3.3)
• The path from Toner Cartridge (K) to Developer (K) for toner blockage
• The Developer (K) for internal toner blockage
• The Toner Cartridge (K) for internal toner blockage

If no problems are found, replace the following parts in sequence:

Can it be a bad transfer belt as when the machine is running it makes a funny noise which when the belt is turned by hand it sounds the same!! Any chance of getting a service cd copy.
Color copies are quite faint and black has prtetty much disappeared. comes and goes

Источник

BSD-ON:

BSD 9.3 — Development and Toner Dispense Control

The frequency at which the ATC Average Fail or the ATC Amplitude Fail has been occurring

has exceeded the threshold value.

NOTE: •

Although this Fault can be cleared by turning the power OFF and ON and it will be possi-

ble to output a few sheets of printouts, when this Fault has occurred a certain number of

times, it will no longer be clearable by turning the power OFF and ON. To clear it, clear the

value of NVM location [752-022] (ATC Average Fail) or NVM location [752-023] (ATC

Amplitude Fail) to «0»

(NVM

Read/Write). If the machine is not repaired back to normal

status, this Fault will occur again during the operation.

•

When turning the power OFF, turn OFF the power switch first and then the main power

switch.

Procedure

Check the following:

•

The connection between the MCU PWB

J615

for open circuit, short circuit, and poor contact

•

The Toner Dispense Motor for revolution failure:

•

The Toner Cartridge for internal toner blockage

If no problems are found, replace the following parts in sequence:

•

Drum Cartridge

(PL

8.1)

•

MCU PWB

(PL

18.2)

Initial Issue

WorkCentre 5335 Family Service Documentation

P/J413

and the Xero/Developer Cartridge

Component Control

[093-002]

(PL

8.2)

BUS Updated 12/2011

092-323 Dispense Fail RAP

BSD-ON:

BSD 9.3 — Development and Toner Dispense Control

Toner Cartridge becomes Empty despite less use of Toner amount.

NOTE: When turning the power OFF, turn OFF the power switch first and then the main power

switch.

Procedure

Check the following:

•

The connection between the MCU PWB

J615

for open circuit, short circuit, and poor contact

•

The Toner Dispense Motor for revolution failure:

•

The Toner Cartridge for internal toner blockage

If no problems are found, replace the following parts in sequence:

•

Drum Cartridge

(PL

8.1)

•

MCU PWB

(PL

18.2)

P/

07/2011

2-831

P/J413

and the Xero/Developer Cartridge

Component Control

[093-002]

(PL

8.2)

Status Indicator RAPs

092-315, 092-323

P/

Xerox error 092 315

КОНФЕРЕНЦИЯ СТАРТКОПИ
Принтеры, копировальные аппараты, МФУ, факсы и другая офисная техника:
вопросы ремонта, обслуживания, заправки, выбора

Добрый день, данный аппарат может напечатать 1-2 листа и вываливается в ошибку 092-315.
Драм весь перебирал, шнек подачи тонера вычистил, тонер тубу также заменил (принтер госконторы, заправляли не понятно чем (тендер) поэтому сразу заменил тубу.) пока безрезультатно.

Инфа по поиску (переведено с буржуйского)
«Чтобы очистить его, очистите значение местоположения NVM [752-022] (средняя ошибка ATC) или местоположение NVM [752-023] (сбой амплитуды ATC ) до «0» ( чтение / запись NVM ).»

а что там очищать не совсем понял, буду признателен за любую информацию.

Вероятно судя по описанию от Вас требуется зайти в nvm rw и в hain link 752-023 и выставить там значение 0. А так. На ровном месте она возникнуть не могла. Тестом компонентов проверьте все ли там у Вас вращается как надо и подается ли тонер куда надо.

Да все вращается уже было проверено, компоненты также все прозванивал. а как зайти в nvm rw и в hain link 752-023 ?

(2)полагаю как обычно. Через ce mode.

Все-таки скорее всего было дело в тонере, сперва распечатал отчеты (есть с полной заливкой) несколько листов и после этого заработал, видать выгнал остатки старого тонера.
Сейчас уже 3 пачка бумаги распечатал. для уверенности пару раз выключал сабж.

Кстати тубу поставил от Xerox 3610 с заменой чипа, одинаковы.

Да у них одна архитектура. Печки тоже очень похожи.
(4) так в нем и было. Вопрос что. Но датчику тонера это явно не понравилось.

Источник

Xerox error 092 315

КОНФЕРЕНЦИЯ СТАРТКОПИ
Принтеры, копировальные аппараты, МФУ, факсы и другая офисная техника:
вопросы ремонта, обслуживания, заправки, выбора

Всем доброго времени суток ! Проблема с МФУ XEROX WC 5325 — после печати или копирования 4-5 листов блокируется и выдаёт ошибку 092-315 . Состояние сбрасывается путём отключения питания МФУ. После включения питания нормально выходит на готовность и после печати или копирования нескольких листов всё повторяется . Подскажите , если кто сталкивался с такой бедой , с чем это связано и как лечить . Или самый лучший вариант — где можно почитать сервисмануал . Заранее всем спасибо .

092-315 ATC Fail
The frequency at which the ATC Average Fail or the ATC Amplitude Fail has been occurring has exceeded the threshold value.
NOTE: Although this Fault can be cleared by turning the power OFF and ON and it will be possible to output a few sheets of printouts, when this Fault has occurred a certain number of times, it will no longer be clearable by turning the power OFF and ON. To clear it, clear the value of NVM location [752-022] (ATC Average Fail) or NVM location [752-023] (ATC Amplitude Fail) to «0» (NVM Read/Write). If the machine is not repaired back to normal status, this Fault will occur again during the operation.
— When turning the power OFF, turn OFF the power switch first and then the main power switch.
Check the following:
— The connection between the MCU PWB P/J413 and the Xero/Developer Cartridge P/J615 for open circuit, short circuit, and poor contact
— The Toner Dispense Motor for revolution failure: Component Control [093-002]
— The Toner Cartridge for internal toner blockage
If no problems are found, replace the following parts in sequence:
— Drum Cartridge
— MCU PWB

Спасибо , почти всё понятно

3. sahrikov1945 24.12.15 22:02

Источник

Thread: Advice Needed: Workcentre 7120 / System Error 092-315 on main display

Thread Tools

Display

Senior Tech 100+ Posts

Join Date Feb 2011 Location West Palm Beach, Fl. Posts 247 Rep Power 30

Advice Needed: Workcentre 7120 / System Error 092-315 on main display

I am getting a system error 092-315 on the main display on startup. Which indicates a ATC Fail (K) Black.

The error codes list states the following 092-315, 092-660, 092-668.

Upon inspection of the drum unit I found the (K) Black toner exit hole packed to the brim with toner
and piling up on top of the back of the drum. I looked at the other drum units (M,C,Y) and found no excess toner.

After vacuuming and cleaning the (K) Black drum unit area as bets as possible, and resetting NVRAM
752-368 (was at 1 reset to zero) 752-372 (was at 3 reset to zero).
Turned machine off (Top Power Button first then inside cover button next) Machine upon starting up printed several blank pages, then there was a metal clink sound and the 092-315 system error redisplayed itself on main screen.

I have determined that one of the following is at fault:
Main Drive Assembly – 007K16710
Dispense Motor -127K61161
Developer Clutch – 121K46371
Drum Drive Motor – 127K61161

Since this a time and materials call, was just looking for opinions on which one of the above would
be most likely to try first?

All help is appreciated, and thanks in advance

Re: Advice Needed: Workcentre 7120 / System Error 092-315 on main display

I am getting a system error 092-315 on the main display on startup. Which indicates a ATC Fail (K) Black.

The error codes list states the following 092-315, 092-660, 092-668.

Upon inspection of the drum unit I found the (K) Black toner exit hole packed to the brim with toner
and piling up on top of the back of the drum. I looked at the other drum units (M,C,Y) and found no excess toner.

After vacuuming and cleaning the (K) Black drum unit area as bets as possible, and resetting NVRAM
752-368 (was at 1 reset to zero) 752-372 (was at 3 reset to zero).
Turned machine off (Top Power Button first then inside cover button next) Machine upon starting up printed several blank pages, then there was a metal clink sound and the 092-315 system error redisplayed itself on main screen.

I have determined that one of the following is at fault:
Main Drive Assembly – 007K16710
Dispense Motor -127K61161
Developer Clutch – 121K46371
Drum Drive Motor – 127K61161

Since this a time and materials call, was just looking for opinions on which one of the above would
be most likely to try first?

All help is appreciated, and thanks in advance

Hello Can you check the following.
Check the following:

• The connection between the MCU PWB P/J411 and the CRUM Reader (K) P/J123 for open circuit, short circuit, and poor contact
• The connection terminals between the Drum Cartridge (K) CRUM PWB and the CRUM Reader (K) for damage and foreign substances
• The Toner Dispense Motor (C,K) for revolution failure: Component Control [093-004] ( PL 5.1)
• The Drum/IBT Drive Motor for revolution failure: Component Control [042-001] ( PL 3.2)
• The Main Drive Motor for revolution failure: Component Control [042-006] ( PL 3.3)
• The Dev K Clutch for failure: Component Control [042-010] ( PL 3.3)
• The path from Toner Cartridge (K) to Developer (K) for toner blockage
• The Developer (K) for internal toner blockage
• The Toner Cartridge (K) for internal toner blockage

If no problems are found, replace the following parts in sequence:

Источник

How to Fix 092-312 to 092-315 092-657 to 092-668 Error Code for Xerox VersaLink C7020 C7025 C7030 C7000 Printer?

Posted by Xwk Tech on Dec 03, 2019

092-312 to 315, 092-657 to 660, 092-665 to 668 ATC Sensor Fault RAP

BSD-ON: BSD 9.5 Development (2 of 2)

092-312 Toner density in the developer unit as detected by the yellow ATC sensor abnormal. This fault occurs when the difference between the maximum and minimum values in the ATC sensor measurement set is lower than the threshold value.
092-313 Toner density in the developer unit as detected by the magenta ATC sensor abnormal. This fault occurs when the difference between the maximum and minimum values in the ATC sensor measurement set is lower than the threshold value.
092-314 Toner density in the developer unit as detected by the cyan ATC sensor abnormal. This fault occurs when the difference between the maximum and minimum values in the ATC sensor measurement set is lower than the threshold value.
092-315 Toner density in the developer unit as detected by the black ATC sensor abnormal. This fault occurs when the difference between the maximum and minimum values in the ATC sensor measurement set is lower than the threshold value.
092-657 Toner density in the developer unit as detected by the yellow ATC sensor abnormal. This fault occurs when the difference between the maximum and minimum values in the ATC sensor measurement set is lower than the threshold value.
092-658 Toner density in the developer unit as detected by the magenta ATC sensor abnormal. This fault occurs when the difference between the maximum and minimum values in the ATC sensor measurement set is lower than the threshold value.
092-659 Toner density in the developer unit as detected by the cyan ATC sensor abnormal. This fault occurs when the difference between the maximum and minimum values in the ATC sensor measurement set is lower than the threshold value.
092-660 Toner density in the developer unit as detected by the black ATC sensor abnormal. This fault occurs when the difference between the maximum and minimum values in the ATC sensor measurement set is lower than the threshold value.
092-665 Toner density in the developer unit as detected by the yellow ATC sensor abnormal. This fault occurs when the average value of the ATC sensor measurement values is not between the upper and lower limit values.
092-666 Toner density in the developer unit as detected by the magenta ATC sensor abnormal. This fault occurs when the average value of the ATC sensor measurement values is not between the upper and lower limit values.
092-667 Toner density in the developer unit as detected by the cyan ATC sensor abnormal. This fault occurs when the average value of the ATC sensor measurement values is not between the upper and lower limit values.
092-668 Toner density in the developer unit as detected by the black ATC sensor abnormal. This fault occurs when the average value of the ATC sensor measurement values is not between the upper and lower limit values.

Initial Actions

• Perform IQ1 to check for a blank page image quality defect.
• Enter dC125. Check for the below faults and perform the applicable procedures as necessary:

– 024-923 to 024-925 Y/M/C Toner Cartridge Empty RAP
– 093-912 Black Toner Cartridge Empty RAP

Procedure

WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.

NOTE: When this fault occurs, toner density control, by the ATC sensor, is not performed and ICDC (pixels) based toner supply control is performed instead. If the fault remains for a long time, image density error (too dark or too light) may occur.

Perform the steps that follow:

1. Switch off, then switch on the machine, GP 10.
2. Check the wiring between the applicable ATC sensor, yellow ( P/J120), magenta ( P/J119), cyan ( P/J118), black ( P/J117) and the drive PWB ( P/J414) for an open circuit, short circuit or damage.
3. If the fault persists , replace a new cartridge CRUM ( toner chip or drum chip ) listed as below or install new components as necessary:

– Black drum cartridge, PL 90.20 Item 5.
– Yellow drum cartridge, PL 90.20 Item 8.
– Magenta drum cartridge, PL 90.20 Item 7.
– Cyan drum cartridge, PL 90.20 Item 6.

– Black toner cartridge, PL 90.05 Item 13.
– Yellow toner cartridge, PL 90.05 Item 10.
– Magenta toner cartridge, PL 90.05 Item 11.
– Cyan toner cartridge, PL 90.05 Item 12.

• Drive PWB, PL 1.10 Item 4.
• ESS PWB, PL 3.10 Item 6.
• HVPS, PL 1.05 Item 7.

**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner’s property.**

You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.

Toner Chip (For North America and West Europe Region):

Toner Chip (For South America and East Europe Region):

Toner Chip (For Metered Machine):

Источник

Thread: Xerox wc 7125 error

Thread Tools

Display

Xerox wc 7125 error

The error is 092-315 any one have ideas. Also does any one have a service manual. sigh

Re: Xerox wc 7125 error

Description

The frequency at which the ATC Average Fail [K] or the ATC Amplitude Fail [K] has been occurring has exceeded the threshold value.
NOTE:

• Although this Fault can be cleared by turning the power OFF and ON and it will be possible to output a few sheets of printouts, when this Fault has occurred a certain number of times, it will no longer be clearable by turning the power OFF and ON. To clear it, clear the value of NVM location [752-368] (ATC Fail [K]) or NVM location[752-372] (ATC Fail Continuous Count [K]) to «0». If the machine is not repaired back to normal status, this Fault will occur again during the operation.
• When turning the power OFF, turn OFF the power switch first and then the main power switch.

Procedure

Check the following:

• The connection between the MCU PWB P/J411 and the CRUM Reader (K) P/J123 for open circuit, short circuit, and poor contact
• The connection terminals between the Drum Cartridge (K) CRUM PWB and the CRUM Reader (K) for damage and foreign substances
• The Toner Dispense Motor (C,K) for revolution failure: Component Control [093-004] ( PL 5.1)
• The Drum/IBT Drive Motor for revolution failure: Component Control [042-001] ( PL 3.2)
• The Main Drive Motor for revolution failure: Component Control [042-006] ( PL 3.3)
• The Dev K Clutch for failure: Component Control [042-010] ( PL 3.3)
• The path from Toner Cartridge (K) to Developer (K) for toner blockage
• The Developer (K) for internal toner blockage
• The Toner Cartridge (K) for internal toner blockage

If no problems are found, replace the following parts in sequence:

Service Manager 1,000+ Posts

Join Date Nov 2007 Location Somewhere in Europe near Black Sea Posts 2,038 Rep Power 60

Re: Xerox wc 7125 error

Problem with readings from ATC sensor for K.
Check K toner transport, K dispenser motor, K toner cartridge and developer for blockage, developer K clutch.

Re: Xerox wc 7125 error

Description

The frequency at which the ATC Average Fail [K] or the ATC Amplitude Fail [K] has been occurring has exceeded the threshold value.
NOTE:

• Although this Fault can be cleared by turning the power OFF and ON and it will be possible to output a few sheets of printouts, when this Fault has occurred a certain number of times, it will no longer be clearable by turning the power OFF and ON. To clear it, clear the value of NVM location [752-368] (ATC Fail [K]) or NVM location[752-372] (ATC Fail Continuous Count [K]) to «0». If the machine is not repaired back to normal status, this Fault will occur again during the operation.
• When turning the power OFF, turn OFF the power switch first and then the main power switch.

Procedure

Check the following:

• The connection between the MCU PWB P/J411 and the CRUM Reader (K) P/J123 for open circuit, short circuit, and poor contact
• The connection terminals between the Drum Cartridge (K) CRUM PWB and the CRUM Reader (K) for damage and foreign substances
• The Toner Dispense Motor (C,K) for revolution failure: Component Control [093-004] ( PL 5.1)
• The Drum/IBT Drive Motor for revolution failure: Component Control [042-001] ( PL 3.2)
• The Main Drive Motor for revolution failure: Component Control [042-006] ( PL 3.3)
• The Dev K Clutch for failure: Component Control [042-010] ( PL 3.3)
• The path from Toner Cartridge (K) to Developer (K) for toner blockage
• The Developer (K) for internal toner blockage
• The Toner Cartridge (K) for internal toner blockage

If no problems are found, replace the following parts in sequence:

Can it be a bad transfer belt as when the machine is running it makes a funny noise which when the belt is turned by hand it sounds the same!! Any chance of getting a service cd copy.
Color copies are quite faint and black has prtetty much disappeared. comes and goes

Источник

BSD-ON:

BSD 9.3 — Development and Toner Dispense Control

The frequency at which the ATC Average Fail or the ATC Amplitude Fail has been occurring

has exceeded the threshold value.

NOTE: •

Although this Fault can be cleared by turning the power OFF and ON and it will be possi-

ble to output a few sheets of printouts, when this Fault has occurred a certain number of

times, it will no longer be clearable by turning the power OFF and ON. To clear it, clear the

value of NVM location [752-022] (ATC Average Fail) or NVM location [752-023] (ATC

Amplitude Fail) to «0»

(NVM

Read/Write). If the machine is not repaired back to normal

status, this Fault will occur again during the operation.

•

When turning the power OFF, turn OFF the power switch first and then the main power

switch.

Procedure

Check the following:

•

The connection between the MCU PWB

J615

for open circuit, short circuit, and poor contact

•

The Toner Dispense Motor for revolution failure:

•

The Toner Cartridge for internal toner blockage

If no problems are found, replace the following parts in sequence:

•

Drum Cartridge

(PL

8.1)

•

MCU PWB

(PL

18.2)

Initial Issue

WorkCentre 5335 Family Service Documentation

P/J413

and the Xero/Developer Cartridge

Component Control

[093-002]

(PL

8.2)

BUS Updated 12/2011

092-323 Dispense Fail RAP

BSD-ON:

BSD 9.3 — Development and Toner Dispense Control

Toner Cartridge becomes Empty despite less use of Toner amount.

NOTE: When turning the power OFF, turn OFF the power switch first and then the main power

switch.

Procedure

Check the following:

•

The connection between the MCU PWB

J615

for open circuit, short circuit, and poor contact

•

The Toner Dispense Motor for revolution failure:

•

The Toner Cartridge for internal toner blockage

If no problems are found, replace the following parts in sequence:

•

Drum Cartridge

(PL

8.1)

•

MCU PWB

(PL

18.2)

P/

07/2011

2-831

P/J413

and the Xero/Developer Cartridge

Component Control

[093-002]

(PL

8.2)

Status Indicator RAPs

092-315, 092-323

P/

In prior articles, we’ve covered the drum cartridges and fusers for this series of full-color MFP copiers. Now let’s see what makes these machines tick—we’ll cover the Fault Code meanings and take a first stab at how to get around in diagnostic mode.

As a refresher, these machines are designed for office use with a duty cycle of around 50K impressions per month. They’re price at around $7,000 new, which is roughly half the cost of a WC-7855. Although they’re not as heavy of a machine, they’re capable of producing fine-looking full-color copies and prints, and are substantial machines in their own right.

This series has a duty cycle of around 50,000 impressions per month, with toner cartridges expected to run about $15,000 (for c/m/y) and $22,000 (for black) assuming 5% coverage. One thing to note is that there is more than one region or “plan.” If you install the wrong version, the machine will reject it because the Customer Replaceable Unit Monitor (CRUM) chip is wrong. There are 4 drum cartridges (R1-R4) which are color specific, as each includes the developer station underneath it. These have a stated yield of around 50-60,000 each (part numbers: 013R00657(K), 013R00658(Y), 013R00659(M), 013R00660(C)). Replacement parts for the drum cartridges and drum count reset CRUM chips are available to repair, rebuild or otherwise extend the yield on these cartridges.

The 2nd BTR (Transfer Roll Assembly) on the left door is R5, good for just under 200,000. There’s also a Transfer Belt Unit (R6) which is fairly easy to replace; it’s considered to be customer replaceable, and has a stated yield of 200,000. Finally, there’s the Toner Waste Container (R7), which comes with a new wand (stored in the front door) for cleaning the ROS windows (the laser-slit glasses). To clean the ROS windows, remove the Waste Container first, and behind there you’ll see the slots where you can slide the wand in and out. Push the wand in slowly until it stops, then retract it slowly for best results.

Next, let’s have a look at some of the fault codes. This list is by no means complete, but should send you in the right direction for most of the common faults. In the list below, some of the hints tell you to “power off completely,” which means turning off the outer power switch first (that one on top of where the front door opens on the right). After the machine is fully powered down, you then need to open the front door to turn off the Inner Main Power Switch on the inside of it.

For reference, here are some acronyms used repeatedly in the fault list:

ATC = Automatic Toner Concentration
ADC = Automatic Density Correction
CRUM = Customer Replaceable Unit Monitory (drum or toner chip)
ESS = Electronic Switching System (the print controller board on the machine)
MCU = Main Control Unit (main board)
NVM = Non-Volatile Memory (machine settings)
ROS = Raster Output Scanner (laser unit)

Note: a handful of fault codes require you to reset NVM settings back to zero before the machine will run again. See the asterisks at the bottom of the table for more info about resetting the fault codes which require the extra step.

FAULT CODE LIST

For 7220/7225, the fault codes will all start with “3” instead of “0.”(e.g. 310-319 = 010-319)

Fault Code	Fault Meaning
002-500	Controller-to-user interface (UI) communication problem
003-xxx faults	Controller (ESS) problems
005-xxx faults	Document feeder (DADF) problems
010-xxx faults	Fuser problems
010-319*	Fuser heat control failure (*must reset from NVM Read/Write, see below)
010-320/333/*	Fuser overheat (*must reset from NVM Read/Write, see below)
010-328	Fuser did not warm up in time (this can happen if the room is cold; power off completely
010-329	Fuser reset fuse failed to blow (hen a new fuser is installed, the machine sees it and attempts to blow the fuse)
010-330	Fuser motor stopped turning (if something is seized up in the fuser or the drives to the fuser, the machine sees that the motor can’t turn)
010-337*	Fuser heat roll paper wrap detected (*must reset from NVM Read/Write,see below)
010-420	Fuser near-end-of-life warning
010-421**	Fuser end of life (**HFSI counter reset recommended)
012-xxx	Finisher faults (too many to list here)
013-xxx	Finisher faults (too many to list here)
016-xxx	Controller problems
018-xxx	Network problems
021-xxx	Foreign device interface (FDI) problems
024-xxx	Controller problems
025-xxx	Hard-drive problems
026-xxx	Scan/controller problems
027-xxx	Network problems
033-xxx, 034-xxx 035-xxx, 036-xxx	Fax problems
041-xxx	Main Control Unit (MCU) problems
042-313	LV rear intake fan failure (127K61770)
042-323	Drum motor failure (check for a bound-up drum cartridge or IBT transfer-belt assembly, which can stall the motor)
042-325	Main motor failure (this motor drives the black developer unit and the paper transport; look for anything which might be binding up)
042-330	Fuser exhaust fan failure
042-337	NOHAD logic failure (ESS to MCU communication problem). Try first to power off completely. If that doesn’t solve the problem, the service manual says to reload the machine software.
042-345	Drum coupling contact failure. Check to see if one of the drum drive couplings in the back of the machine is “stuck” behind the frame; all 4 should be out a bit and spring loaded to mate with the couplings on the rear of the drum cartridges.
042-346	Drive logic failure (ESS to MCU communication problem). Try first to power off completely. If that doesn’t solve the problem, the service manual says to reload the machine software.
045-322	Image processing errors
061-xxx	ROS (laser unit) problems
062-xxx	Generally IIT (scanner) problems
062-277	ESS to DADF (document feeder) communication failure
062-300	Platen interlock switch open; check the DADF hinge for breakage
071-105 = T1 072-105 = T2 073-105 = T3 074-105 = T4	Tray 1, 2, 3 or 4 paper jam (paper from tray 1, 2, 3 or 4 failed to reach registration sensor)
071/072/073/ 074-210	Tray 1, 2, 3 or 4 lift failure
071/072/073/ 074-212	Tray 1, 2, 3 or 4 paper-size sensing problem
072/073/ 074-101	Tray 2, 3, or 4 misfeed
072/073/ 074-900	Tray 2, 3 or 4 feed out sensor static jam (paper remaining on feed sensor)
075-135	Tray 5 (bypass/MSI) paper jam (failed to reach registration sensor)
077-101	Registration jam (paper never left the registration sensor)
077-103 or 106	Exit sensor 1 jam (paper never left sensor OR never reached sensor)
077-105 or 109	Exit sensor 2 jam (paper never left sensor OR never reached sensor)
077-110	POB (paper on belt) sensor sensed paper on the transfer belt
077-123/130	Registration sensor (duplexed page did not reach registration sensor)
077-131	Duplex jam (paper never reached the duplex wait sensor)
077-211	Tray 3/4 module mismatch (two-tray module vs. tandem tray module)
077-212 or 214	Tray 3/4 module reset fail OR logic fail
077-215	Tray module communication failure
077-300	Front cover interlock open
077-301	Left cover interlock open (main left cover)
077-305	Tray module left cover interlock open
077-307	Duplex cover interlock open
077-308/077-309	Left-upper cover open/ left-lower cover open
077-314	Paper handler module logic failure
077-900	Paper detected on registration sensor after jam clearance
077-901/902	Exit sensor 1/ 2 static jam (paper detected on sensor after jam clearance)
077-903	POB (paper-on-belt) sensor jam (paper detected after jam clearance)
077-907	Duplex wait jam (paper detected on sensor after jam clearance)
089-xxx	Color registration control failures
091-313	CRUM chip ASIC communication failure
091-400/911	Toner waste bottle nearly full/ waste bottle full
091-401/402	Black drum cartridge, near end of life / end of life
091-407	Black drum CRUM chip problem
091-411 or 417	Yellow drum cartridge, near end of life OR drum CRUM chip problem
091-421 or 427	Magenta drum cartridge, near end of life OR drum CRUM chip problem
091-431 or 437	Cyan drum cartridge, near end of life OR drum CRUM chip problem
091-480/481/482	Yellow/Magenta/Cyan drum cartridge, end of Life
091-910	Waste toner bottle not in correct position (or not installed)
091-913	Black drum cartridge, end of life
091-914/ 915/916	Black drum CRUM failure/broken data/wrong CRUM version
091-917/ 918/919	Yellow/Magenta/Cyan drum CRUM chip – communication failure
091-921/927/ 928/929	Black/Yellow/Magenta/Cyan drum CRUM, out of position or missing
091-936/937/ 938/939	Yellow/Magenta/Cyan drum CRUM, wrong CRUM version (data mismatch)
091-940/941/ 942/943	Yellow/Magenta/Cyan drum CRUM chip, broken data failure
092-312*	Yellow ATC sensor failure (auto toner concentration); toner dispense problem for yellow, requires reset from diagnostics*
092-313*	Magenta ATC sensor failure (automatic toner concentration); toner dispense problem for magenta, requires reset from diagnostics*
092-314*	Cyan ATC sensor failure (automatic toner concentration); toner dispense problem for cyan, requires reset from diagnostics*
092-315*	Black ATC sensor failure (automatic toner concentration; toner dispense problem for black, requires reset from diagnostics*
092-649	ADC shutter open failure (automatic density concentration)
092-650	ADC shutter close failure
092-661	Temperature sensor failure (internal machine temperature too high)
092-662	Humidity temperature sensor failure
093-314/315/ 316/317	Yellow/Magenta/Cyan/Black toner dispense motor problems
093-320	Developer drive motor failure (Y/M/C)
093-426/427/ 428/429	Black/Yellow/Magenta/Cyan toner ctg. CRUM chip error
093-912	Black toner cartridge empty
093-916	Black Toner CRUM chip – out of position / communication failure / data broken failure / wrong CRUM version (data mismatch)
093-941/ 942/943	Magenta/Cyan/Yellow toner CRUM chip communication failure
093-948	Yellow developer install time failure (drum ctg. failed to initialize developer)
093-950/ 951/952	Yellow/Magenta/Cyan toner CRUM chip data broken failure
093-953/954/ 955/956	Yellow/Magenta/Cyan/Black developer install fail (pull seal from yellow drum ctg.)
093-957/ 958/959	Magenta/Cyan/Black developer install time failure (pull seal from magenta drum ctg.)
093-960/ 961/962	Yellow/Magenta/Cyan toner cartridge CRUM chip, wrong CRUM chip (data mismatch)
093-970/ 971/972	Yellow/Magenta/Cyan toner CRUM chip out of position or missing
094-417	IBT belt (transfer belt) unit is nearing end of life
094-419	2nd BTR (transfer roll) is nearing end of life
094-420**	IBT Belt (transfer belt) unit, end of life (**HFSI reset required)
094-422**	2nd BTR (transfer roll) unit, end of life (**HFSI reset required)
094-910	IBT belt unit, OR 2nd BTR unit out of position or not installed
102-xxx	Generally UI (user interface/control panel) problems
116-xxx	Generally controller problems
117-xxx	Generally controller problems (UI/EWS)
118-310	IPSEC failed to initialize
121-xxx	Generally FDI (foreign device interface) problems
123-xxx	Generally UI (user interface/control panel) problems
124-xxx	Generally billing & serial number errors
125-311	Controller problem with PSW cont. software (UI/EWS)
127-xxx	Generally external communications
133-xxx & 134-xxx	Fax problems
202-xxx	Timer failures

*Faults requiring reset from NVM Read/Write

Some codes require setting a particular NVM code back to “0” to clear the fault. Enter diagnostic mode and choose “NVM Read/Write” reset the value of the specified code back to “0” (read more below).
*010-319/010-320/010-333/010-337 fuser faults—reset NVM code 744-248 back to “0”
*092-312 Yellow toner dispense fault—reset NVM codes 752-365 & 752-369 back to “0”
*092-313 Magenta toner dispense fault—reset NVM codes 752-366 & 752-370 back to “0”
*092-314 Cyan toner dispense fault—reset NVM codes 752-367 & 752-371 back to “0”
*092-315 Black toner dispense fault—reset NVM code 752-368 & 752-372 back to “0”

**Faults requiring reset from dC135 HFSI (high-frequency service items)

1. Entering Diagnostics Mode
Hold down “0” for at least 5 seconds
2. While holding “0,” press “Start”
A passcode screen shows up, enter “6789” and touch “Confirm”
Press “Machine Status” and choose the “Tools” tab
3. Choose “System Settings,”
4. In the center ”group” column, choose “Common Service Settings”
5. In the right column (features), scroll down to “Maintenance/Diagnostics” and choose “NVM Read/Write”

*NVM Read / Write (Memory Settings)

To reset some fault codes:
Enter diagnostics mode and touch “NVM Read/Write”
Enter the NVM code (chain-link code) and touch “Confirm/Change” (t will show you the “Current Value”)
Enter a “0” in the “New Value” column and touch “Save”
Select “Close” and finally “Exit” diagnostics
The machine will need to reboot for the NVM changes to take place and for the machine to attempt to come to ready again, now that the fault code has been cleared.

**HFSI Counter Resets

The CRUs should automatically reset when the customer installs the assembly, but the product manual also presents a way to access HFSI counters from diagnostic mode. This may be helpful if a new module fails to reset properly. After you enter Diagnostics Mode (read above):

• For the 7220/7225: press “Service Info” or the “Maintenance” tab and choose “Dc135 CRU/HFSI Counters.” Scroll through the list, choose the HFSI item and touch “Reset Counter.”
• For the 7120/7125: enter diagnostics mode, choose “Adjustment/Others,” then select “HFSI Counter.” Select the HFSI from the list and press “Details,” followed by “Reset Current Value.”

Special Boot Modes

This is helpful for clearing jobs when they get stuck in the queue. Hold down the buttons specified below while turning on the power, and keep holding them until the boot screen (progress bar) appears.

Job Log Initialize: hold down “1,” “Stop,” and “Energy Saver” buttons while powering on.

Spool Log Initialize: hold down “6”, “Stop,” and “Energy Saver” buttons while powering on.

HDD (hard drive) Initialize: Hold down “4,” “Stop,” and “Energy Saver” buttons while powering on (WARNING: all customer data will be deleted if you do this. Make sure to create backups of all data set before you initialize the HDD)

Now that we’ve scratched the surface on this series of machines, hopefully they will be more approachable for everyone. Happy repairs.

1. 05-09-2017

   
   

   #1

   

   
   Technician
   

   

   ---

   Join Date

   Jul 2014

   Posts

   32

   Rep Power

   19

   Fuji Xerox IV C2260 (092-314)
   

   I have error 092-314, Is anyone able to tell me what that error code is in this model? I don’t have the manual for that actual model, but i believe its ATC (cyan) fail, is this correct if so is there a reset once the Cyan has been replaced?

   ---

Херокс 7120 пишет ошибка 092-314 что делать подскажите