Xerox 5230 ошибка 124 373 - Решение и исправление самых разных ошибок на TopOshibok.ru

124-372, 373, 374 IOT Soft Fail RAP

124-372 IOT controller software failure.
124-373 IOT manager software failure.
124-374 IOT IM device driver software failure.

Procedure

WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause death or injury. Moving parts can cause injury.

Perform the steps that follow:

1. Switch off, then switch on the machine, GP 10.
2. Ensure that all connectors on the ESS PWB, PL 3.10 Item 6 are securely connected. Ensure all surface mounted modules are securely connected.
3. Reload the software, GP 4.
4. Perform the OF2 Special Boot Modes RAP.
5. If the fault persists, install a new ESS PWB, PL 3.10 Item 6.

**This RAP is from Xerox Service Manual. All brand names and trademarks are their respective owner’s property.**

You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.

Toner Chip (For North America and West Europe Region):

• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738

Toner Chip (For South America and East Europe Region):

• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766

Toner Chip (For Metered Machine):

• 106R03733 106R03736 106R03735 106R03734

Drum Chip:

• 113R00780 113R00782

System Fail. IOT Manager Software Failure. An error in the IOT Manager software was

detected.

Procedure

•

Turn the power OFF then ON. If the problem persists, perform the following procedure to

repair it.

•

Ensure that the customer is programming a job within the parameters of the machine uti-

lizing the UI.

•

Disconnect then reconnect the IIT, UI I/F, ESS, MCU all PWBs connected to them (RAM,

Firmware module, EEPROM)

•

Check the sw version of the controller sw — update if required

•

Replace MCU PWB

(PL

18.2)

•

Replace ESS PWB

(PL

35.2) (If not fixed by this, reinstall the original ESS PWB & MCU

PWB)

Status Indicator RAPs

124-373, 124-374

124-374 IOT Controller Software RAP

Due to an error in the software of the IOT Controller, subsequent processes cannot be per-

formed.

Procedure

•

Turn the power OFF then ON. If the problem persists, perform the following procedure to

repair it.

•

Ensure that the customer is programming a job within the parameters of the machine uti-

lizing the UI.

•

Disconnect then reconnect the IIT, UI I/F, ESS, MCU all PWBs connected to them (RAM,

Firmware module, EEPROM)

•

Reload Firmware

•

Replace MCU PWB

•

Replace ESS PWB

PWB)

07/2011

2-980

BUS Updated 12/2011

(GP

16).

(PL

18.2)

(PL

35.2) (If not fixed by this, reinstall the original ESS PWB & MCU

WorkCentre 5335 Family Service Documentation

Initial Issue

Современные копировальные аппараты Xerox отличаются качество, надежностью и «быстрым» стартом. Также у них существует множество особенностей, которые отличают их от принтеров других производителей. Например, используется тефлоновый вал, а не термопленка.

Однако избегать различных поломок и ошибок пока не удается ни одному устройству. К самым частым неисправностям у принтеров Xerox относятся: залипание или повреждение датчика бумаги, повреждение роликов подачи, часто требуется перепрошивка программного обеспечения.

Если у вас возникнут вопросы насчет того, как исправить код ошибки копировального аппарата Xerox, то вы можете обратиться к специалистам нашего сервисного центра.

Основные коды ошибок копировальных аппаратов Xerox и способы их устранения:

Коды ошибок Xerox 1012, 1012(RE)
Коды ошибок Xerox 1020
Коды ошибок Xerox 1025
Коды ошибок Xerox 1035
Коды ошибок Xerox 1038
Коды ошибок Xerox 2830
Коды ошибок Xerox 5011, 5012, 5014
Коды ошибок Xerox 5016, 5017, 5316, 5317
Коды ошибок Xerox 5018, 5028
Коды ошибок Xerox 5312, 5313, 5314
Коды ошибок Xerox 5318, 5320, 5322
Коды ошибок Xerox 5328
Коды ошибок Xerox 5330
Коды ошибок Xerox 5340, 5343
Коды ошибок Xerox 5345
Коды ошибок Xerox 5350, 5352
Коды ошибок Xerox 5355
Коды ошибок Xerox 5622
Коды ошибок Xerox XC520, 540, 560, 580

Xerox 1012, 1012(RE)

Код ошибки	Описание
E1	Jam between paper feed and fuser
E3	Jam in fuser
E5	Clam shell open
E6	Paper feed section cover is open
J1	Toner cartridge near empty
J3	Drum cartridge not seated properly
J7	Waste toner full (replace drum cartridge)
L6	Key counter out
L8	Exposure area overheat
U1	No clock pulse (drive problem)
U2	Scan problem
U3	Lens/mirror problem (RE model only)
U4	Heat problem
U8	Exposure lamp control circuit problem
E1	Jam between paper feed and fuser
E3	Jam in fuser
E5	Clam shell open
E6	Paper feed section cover is open
J1	Toner cartridge near empty
J3	Drum cartridge not seated properly
J7	Waste toner full (replace drum cartridge)
L6	Key counter out
L8	Exposure area overheat
U1	No clock pulse (drive problem)
U2	Scan problem
U3	Lens/mirror problem (RE model only)
U4	Heat problem
U8	Exposure lamp control circuit problem

Xerox 1020

Код ошибки	Описание
LL	Probable bad heater lamp

Xerox 1025

Код ошибки	Описание
A1	DF jam
C1	PF jam cass. 1
C2	PF jam cass. 2
C3	PF jam cass. 3
C9	Bypass jam
E1-1	Paper jam before exit switch
E1-2	Paper jam
E1-5	Paper jam
E1-6	Paper jam
E3-3	Paper jam at exit switch
E3-4	Paper jam at exit switch
E5	Front door open
F1	Collator jam
F5	Collator interlock
F8	No power to collator
F9	Collator bin home switch
J7	250 copies since toner waste was full
L5	Original cass. not present after clearing interrupt
L6	Key counter
L8	Platen glass too hot
U1	Main motor clock pulse
U2	Scan problem
U3-1	Lens problem
U4-1	Open thermistor
U4-2	Low temperature
U4-4	Temperature
U4-5	Main PWB
U6-1	Main PWB
U6-2	Main PWB
U6-3	Main board battery
U6-4	Initialization
U8	Exposure lamp

Xerox 1035

Код ошибки	Описание
A9	Scanner location
C1	Paper feed — upper cassette
C2	Paper feed — lower cassette
C9	Bypass jam
E5	Clam shell is open
L6	Key counter
U1	Off/On
U2	Optics
U4	Low fuser temperature

Xerox 1038

Код ошибки	Описание
A1	DF jam
C1	PF jam cass. 1
C2	PF jam cass. 2
C3	PF jam cass. 3
C9	Bypass jam
E1-1	Paper jam before exit switch
E1-2	Paper jam
E1-5	Paper jam
E1-6	Paper jam
E3-3	Paper jam at exit switch
E3-4	Paper jam at exit switch
E5	Front door open
F1	Collator jam
F5	Collator interlock
F8	No power to collator
F9	Collator bin home switch
J7	250 copies since toner waste was full
L5	Original cass. not present after clearing interrupt
L6	Key counter
L8	Platen glass too hot
U1	Main motor clock pulse
U2	Scan problem
U3-1	Lens problem
U4-1	Open thermistor
U4-2	Low temperature
U4-4	Temperature
U4-5	Main PWB
U6-1	Main PWB
U6-2	Main PWB
U6-3	Main board battery
U6-4	Initialization
U8	Exposure lamp

Xerox 2830

Код ошибки	Описание
A9	Scanner location
C1	Paper feed — upper cassette
C2	Paper feed — lower cassette
C9	Bypass jam
E5	Clam shell is open
E5	Clam shell open
L6	Key counter
U1	Off/On
U2	Optics
U4	Low fuser temperature

Xerox 5011, 5012, 5014

Код ошибки	Описание
C8	Bypass jam/no paper
C9	Bypass jam
E1	Jam
E3	Fuser jam
E5	Clamshell open
E6	PF section cover open
J1	Toner cartridge amost empty
J3	Copy cart (drum unit) missing/not seated right
J7	Copy cartridge has run 18,000 copies
J8	Copy cartridge. Improperly seated or possible only one of two fuses in the cartridge blew
L6	Key counter
L8	Exposure glass too hot
U1	Drive problem
U2	Scan problem
U3	Lens or mirror drive problem
U4	Fuser problem. Heat lamp, thermoswitch, SSR, thermistor
U6	Battery on main board
U8	Exposure lamp or exposure lamp circuit

Xerox 5016, 5017, 5316, 5317

Code	Description
A1-1	Document feeder feed jam
A1-2	Document feeder belt jam
A2-1	Document feeder exit jam
A2-2	Duplex jam
A3	DAD interlock
A5	Duplex and DAD right side interlock
A6	Copier jams after
A9	Document feed belt drive motor
C1-3	Top cassette misfeed
C2-3	Middle cassette misfeed
C3-3	Bottom cassette misfeed
C9-3	Bypass misfeed
E1-11 to E1-14	Paper jam in machine. Did not reach exit switch soon enough
E1-6	Paper path jam
E3-31 to E3-34	Exit switch jam
E3-6	Fuser jam
E5	Front door interlock
E6	Right side interlock or TTM interlock
F1	Sorter jam
F5	Sorter interlock
F8	Sorter board to copier main board communication problem
F9	Sorter bins

Xerox 5018, 5028

Code	Description
A1	Document is ADF
A1-8	Main board received reset signal
A2	ADF jams
A6, A7	ADF jams
A9	ADF jams
C1 — C4	Feed jam
C5-1 to C5-4	Jams in various areas
C5-2	Jams in various areas
C5-3	Jams in various areas
C5-4	Duplex jam
E0	Machine has reset
E1	Jam
E1-E0	Registration jam
E1-E5	Clamshell interlock
E1-E6	Right side interlock
E1-E7	Two tray interlock
E1-E8	Sorter interlock
E1-E9	Copy cartridge interlock
E2	Reset signal happened
E3	Jam
E4	Exit jam
E4-10	Exit jam
E4-5	Clamshell interlock
E4-6	Right side interlock
E4-7	Two tray interlock. Duplex interlock
E4-8	Sorter interlock
E4-9	Copy cartridge interlock
E5	Clamshell interlock
E6	Right side interlock
E7	Duplex interlock
E9	Copy cartridge interlock
F3-1	Sorter bin home switch
F3-2	Sorter cam switch
F3-3	Sorter cam switch
J1-1	Add toner
J1-2	Temporary low toner signal
J2-0	Replace copy cartridge
L2	2000 copies left on copy cartridge
L3	ADF to machine communication problem
L4 (flashing)	1000 copies left on fuser web
rr	Bad EPROM on main board
U0	Main board
U2	Scan problem
U2-1	Scan home
U3-00	Cam drive problem
U3-01	Cam movement slow
U3-04	Main board to duplex communication
U3-09	Cam problem
U3-12	Jogger problem
U3-19	Cam problem
U3-21	Cam problem
U3-23	Cam problem
U3-29	Cam problem
U3-32	Cam problem
U3-34	Cam problem
U3-39	Cam problem
U3-43	Cam problem
U3-45	Cam problem
U3-49	Cam problem
U3-54	Cam problem
U3-56	Cam problem
U3-59	Cam problem
U4-1	Fuser problem. Long warm up
U4-2	Low fuser temperature after warm up
U4-3	High fuser temperature
U4-4	Open fuser thermistor
U4-6	Replace fuser web
U4-7	Thermistor signal problem
U7-1	Copy cartridge belt drive problem
U9-3	Exposure lamp problem
U9-4	Toner motor
U9-5	Problem in warm up

Xerox 5312, 5313, 5314

Код ошибки	Описание
C1	Upper paper feed problem. Did not reach feed sensor
C2	Lower paper feed problem. Did not reach feed sensor
E1	Exit jam. Paper did not reach exit sensor
E3	Exit jam. Paper still on exit sensor
J1	Add toner
J3	Copy cartridge (drum unit) not installed
J7	Copy cartridge (drum unit) must be replaced
J8	Copy cartridge (drum unit) problem
L6	Problem with an accessory. Installed but not initialized
U1	Drive problem. Main motor, gear etc.
U2	Scan problem
U3	Main board dip switches wrong. Lens drive problem
U4	Fuser problem. Heat lamp, thermal switch, overheat, thermistor.
U6	EPROM error
U8	Auto exposure sensor. No exposure lamp or weak lamp

Xerox 5318, 5320, 5322

Code	Description
A1-11	Original ready switch
A1-12	Feed sensor
A1-1 to A1-32	All indicate a paper path problem, etc. in the ADF
A1-21	Original ready switch and document registration sensor or both the document feed sensor and document registration sensor
A1-22	ADF registration sensor
A1-23	Original did not reach ADF registration sensor quickly enough
A1-24	ADF sensor stuck down too long
A1-25	ADF sensor actuated at the wrong time during single sheet feed
A1-26	ADF sensor not actuated quickly enough in sheet feed mode
A1-31	In reverse, ADF sensor is not actuated soon enough
A1-32	In reverse, ADF sensor is actuated too long
A2	ADF exit problems
A2-1	Original ready sensor and ADF exit switch are actuated or ADF feed in sensor and ADF exit switch are both actuated
A2-2	ADF exit switch
A2-3	ADF exit switch is not actuated on time
A3	Irregular size documents
A3-1	Wrong size original sensed in 1:1 mode
A3-2	Wrong size original sensed in the 2:1 mode
A5	ADF interlock
A5	ADF interlock
A6	ADF single sheet document reset.
A6-1	Reset original
A6-2	Reset sheet feeder
A7	Document cover interlock
A8	ADF exit interlock
C1	Tray 1 jam
C1-2	Paper feed problem in tray 1
C1-3	Paper does not reach registration
C2	Tray 2 jam
C3	Tray 3 jam
C3-1	Paper feed problem from tray 3
C3-2	Paper feed problem from tray 3
C3-3	Paper feed problem from tray 1
C6-1	Duplex paper feed problem
C6-2	Duplex and/or tray 1 paper feed problem
C6-3	Paper feed problem from tray 1
C7-1	Paper feed problem from HCF
C7-2	Paper feed problem from HCF on tray 1
C7-3	Paper feed problem from tray 1
C8	Paper stays in tray or duplex or HCF
C8-1	Paper on tray 1 feed sensor
C8-2	Paper on tray 2 feed sensor
C8-3	Paper on tray 3 feed sensor
C8-4	Paper on HCF feed sensor
C8-5	Paper in duplex section
C9	Bypass feed problem
C9-3	Paper from bypass did not reach registration sensor quickly enough
E1-10 to E1-25	Internal jam
E1-6	Paper on registration sensor
E2	Reset signal happened. Might read E-2 something else.
E3-30 to E4-14	Exit jam
E3-30 to E3-35	Exit switch actuated too long
E3-6	Exit jam
E3-6	Paper on exit switch
E4-10 to E4-14	Inverter sensor not actuated.
E4-10 to E4-45	Paper did not reach inverter switch soon enough
E4-15	Inverter sensor
E4-40 to E4-45	Duplex entry sensor
E4-6	Paper on inverter switch
E4-6	Inverter sensor
E5	Front door interlock
E6-1	Tray 1 interlock
E6-2	2 tray or duplex interlock
E6-3	HCF interlock
E7-2	Duplex inverter interlock
E7-3	Duplex interlock
E8-10 to E8-15	Paper on duplex feed sensor is not actuated soon enough
E8-6	Paper in duplex
E8-6 to E8-15	Duplex entry sensor
F1-1	Paper did not reach sorter
F1-2	Paper stayed on sorter feed sensor
F1-6	Sorter exit sensor
F3	Paper size not available for sort/stack
F5	Sorter interlock
H2-1	Communication problem between main board and duplex board
H2-2	Side guard sensor problem
H3-1	Communication problem between main board and HCF
H3-2	Upper limit sensor problem on HCF
H6-1	ADF size sensor
H6-2	ADF nudgeer sensor
H6-3	Belt drive motor does not have 24 volts. Black toner is empty, but 100 copies have been run without changing toner
J1	Black toner is empty, but 100 copies have been run without changing toner
J3	Replace copy cartridge
J3	No copy cartridge (drum unit)
J7	Copy cartrige must be replaced
J8-1	Wrong copy cartridge installed
J8-2	Copy cartridge EEPROM must be changed
L6	Auditron or other counter problem
L6	Key counter not installed
L8	Platen glass temperature is too high
L9	Communication problem between interimage erase/edge lamps and main board
U1-1	Main motor drive problem
U2-1	Scan home problem
U2-1 to U2-4	Scan home sensor
U2-2	Scan home problem or optics problem
U2-3, U2-4	Scan home problem
U3-1	Lens sensor problem
U4-1	Fuser thermistor open
U4-2	Fuser did not warm up properly
U4-3	Fuser temperature too high
U4-4	Fuser problem. Staying on too long
U4-6	High fuser temperature
U5-1	Sorter bin home switch not activated
U5-2	Sorter bin home switch stayed actuated
U5-3	Sorter bin home switch
U5-4	Sorter bin home switch
U6-1	ROM problem
U6-2	RAM problem
U6-3	Low battery
U6-4	Incorrect value in NVM. Reinitialize main board with code 20-96
U8-1	Exposure lamp problem
U8-2	Communication problem main board and exposure board
U8-3	Exposure lamp or exposure lamp board problem
U8-4 to U8-6	Problem with exposure lamp, lamp sensor, lamp board

Xerox 5328

Code	Description
A1	Document in ADF
A1-8	Main board received reset signal
A2	ADF jams
A6	ADF registration jam
A7	ADF interlock
A9	Tray 1 jam
C1	Tray 2 jam
C2	Tray 3 jam
C3	Bypass feed jams
C4	Machine has reset
E1	Jam
E1-5	Clamshell interlock
E1-6	Right side interlock
E1-7	Two tray interlock, or duplex interlock
E1-8	Sorter interlock
E1-9	Copy cartridge interlock
E1 or E1-0	Registration jam
E2	Reset signal happened
E3	Jam in transfer area
E4	Exit jam
E4-0	Exit jam
E4-5	Clamshell interlock
E4-6	Right side interlock
E4-7	Two tray interlock
E4-8	Sorter interlock
E4-9	Copy cartridge interlock
E5	Clamshell interlock
E6	Right side interlock
E9	Copy cartridge interlock
F3-1	Sorter bin home switch
F3-2	Sorter cam switch
F3-3	Sorter cam switch
F5	Sorter interlock
J1-1	Add toner
J1-2	Temporary low toner signal
J2-1, J2-2	Replace copy cartridge
J5, J6	ADF to machine communications problem
L2	2000 copies left on cartridge
L3	ADF to machine communications problem
L4	(flashing) 1000 copier left on fuser web
L6	Auditron or other counter problem
LL	Main board. Try simulation 1.1 to initialize
rc	Wrong operation panel installed
rr	Bad EPROM on main board. Try 1.1
U0	Main board
U2	Scan problem
U2-1	Scan home
U2-2	Scan home or scan encoder
U2-4	Scan home or scan dual page sensor
U2-7	Scan home
U4-1	Fuser problem. Long warm up
U4-2	Low fuser temperature after warm up
U4-3	High fuser temperature
U4-4	Open fuser thermistor
U4-6	Replace fuser web.
U4-7	Thermistor signal problem
U7-1	Copy cartridge belt drive problem
U9-3	Exposure lamp problem
U9-4	Toner motor
U9-5	Problem in warm-up

Xerox 5330

Code	Description
A1-1 to A1-32	All indicate a paper path problem, etc. in the ADF.
A2	ADF exit problems
A3	Irregular size documents
A5	ADF interlock
A6	ADF single sheet document reset.
A7	Platen interlock
A8	ADF exit interlock
C1	Tray 1 jam
C2	Tray 2 jam
C3	Tray 3 jam
C6-1, C6-2	Jams related to duplex
C6-3	Registration sensor, re tray 1
C7-1, C7-2	HCF feed problems
C7-3	Tray 1 feed problem
C8	Paper stays in tray or duplex or HCF
C9	Bypass feed problem
E1-10 to E1-25	Internal jam
E1-6	Paper on registration sensor
E2	Reset signal happened. Might read E-2 something else.
E3-30 to E4-14	Exit jam
E3-6	Exit jam
E4-10 to E4-14	Inverter sensor not actuated.
E4-15	Inverter sensor
E4-40 to E4-45	Duplex entry sensor
E4-6	Inverter sensor
E5	Front door interlock
E6-1	Tray 1 interlock
E6-2	2 tray or duplex interlock
E6-3	HCF interlock
E7-2, E7-3	Duplex interlock
E8-6 to E8-15	Duplex entry sensor
F1-1	Sorter entry sensor
F1-6	Sorter exit sensor
F3	Paper size not available for sort/stack
F5	Sorter interlock
J1	Add toner
J3	Replace copy cartridge
J7	Replace copy cartridge
J8-1	Wrong copy cartridge installed
J8-2	Copy cartridge EEPROM
L6	Auditron or other counter problem
L8	Platen glass temperature is too high
L9	Communication problem between interimage erase/edge lamps and main board
U1-1	Main motor drive problem
U2-1 to U2-4	Scan home sensor
U3-1	Lens sensor
U4-1	Open fuser thermistor
U4-2	Fuser did not warm up properly
U4-3	Fuser temperature too high
U4-4	Fuser problem. Staying on too long
U4-6	High fuser temperature
U5-1	Sorter bin home switch not activated
U5-2	Sorter bin home switch stayed actuated
U5-3	Sorter bin home switch
U5-4	Sorter bin home switch
U6-1	ROM problem
U6-2	RAM problem
U6-3	Low battery
U6-4	Incorrect value in NVM. Reinitialize main board with code 20-96
U8-1 to U8-6	Problem with exposure lamp, lamp sensor, lamp board

Xerox 5340, 5343

Code	Description
00-009; 030 to 033	A door was opened while paper was being fed
00-047	Paper in duplex
00-1	Auditron
00-2	Diagnostic error
00-3	Faults error
00-4	Ric error
00-5	Job manager system error
00-6	LLM interface
00-7	Standby error
00-8	Communications error
00-9	Xerographic error
01-300	Front interlock
01-310	Right upper interlock
01-315	Left upper interlock
01-320	Left lower interlock
01-325	Fuser interlock
02-910	Key counter missing
02-920	Wrong combination of accessories
03-321, 322, 326, 327	LLM to ISIL communications problems
03-328	IOT communications problem with duplex or tray 4
03-330	IOT communications problems with HCF
03-335, 03-336	LLM communications problems with edit
03-340	NVM memory
03-341, 03-347	Communications problems between IOT and sorter
03-350, 03-354	Communications problem with LLM and user interface
03-363, 03-364	Communications problem between LLM & optics
03-370, 03-373	Communications problem between LLM & DADF
03-380, 384
03-416, 03-422	RAM memory problem
03-424, 426	NVM memory problem
03-430, 432	Billing problem
03-439	GRAIB communications problem
03-440	RIC communications problem
03-441	RIC NVM problem
03-442	Modem
03-443, 03-458	RIC problems
03-460	Serial communications processor problem
04-300	Main motor or drive problem
05-100, 05-108	DADF registration sensor
05-110	DADF exit sensor
05-115, 120	DADF jams
05-305	DADF document drive
05-310, 312	DADF document sensor
05-316	DADF registration sensor jam
05-325	DADF exit sensor
05-335, 341, 345	DADF interlock switches
06-300, 06-310	Scan problems
06-315	Scan drive
06-320A, 320B, 320C, 325	Scan problem
06-330	Lens drive
06-340	Exposure control problem
06-342	LLM CPU problem
06-344, 06-350	Exposure cvontrol problem
06-352	IOT CPU problem
07-300, 315, 330, 345	Tray faults
07-360, 07-370	HCF problems
07-375, 380A, 380B	Duplex problems
08-100, 08-110	Feed problems. Lead edge of copy paper is late getting to feed sensor of tray 1
08-115, 08-162	Feed problem. Lead edge of copy paper is late getting to registration sensor
08-165	Paper jam at registration sensor
08-310, 08-370	Paper at a sensor when power is turned on
08-330	DADF nudger sensor
08-380	Registration side to side problem with home position
08-390	Nip
09-300	Copy cartridge finished (drum unit)
09-310	Add black toner Add color toner
09-320	Add color toner
09-330	Wrong copy cartridge (wrong drum unit)
09-340	Drum cartridge not installed properly
09-350	Waste toner full
100	A fault has occurred
10-100	Exit jam
10-105	Exit jam
10-110	Vertical sensor jam
10-120, 122, 125	Duplex jam
10-150, 155	Too much or not enough paper in duplex tray
10-300	Fuser thermistor
10-302	Low fuser temperature
10-304	Bad fuser temp
10-308	High fuser temperature or open thermistor
10-310	High fuser temperature
10-312	Fuser not up to temperature after energy save
10-314	Fuser problem
10-320	Fuser web finished
10-330, 335, 340	Exit switch, vertical sensor switch actuated when power is turned on
11-100, 11-116	Sorter jam
11-150, 11-176	Sorter auto stapler jam
11-310, 314, 316	Sorter interlock
11-325A, B, C, D, E, F, G	Sorter index
11-352, 354, 356	Sorter auto stapler interlocks
11-365A, B, C, D, E	Sorter auto stapler bin
11-370, 371, 372A, 373A, 373B, 374	Sorter auto stapler staple failure, staple home problem or tamper home problem
11-385A, 385B, 390A,B,C,D,E, 396A	Sorter auto stapler staple failure, staple home problem or tamper home problem
301	Fuser web must be replaced
302	Copy cartridge (drum unit) must be replaced
501	Tray 1 must be rebuilt
502	Tray 2 must be rebuilt
503	Tray 3 must be rebuilt
504	Tray 4 must be rebuilt
505	HCF must be rebuilt
506	Bypass must be rebuilt
507	Duplex unit must be rebuilt
508	Replace black developer
509	Replace red developer
510	Replace green developer
512	Replace brown developer
513	Copy cartridge (drum unit) will need replacing soon
514	Fuser web will need replacing soon
515	DADF belt should be replaced
516	DADF feed rollers should be replaced
517	Replace exposure lamp
518	Replace suction filter
519	Replace ozone filter
520	Replace optics filter
521	Replace particle filter
522	Replace upper fuser roller
523	Replace fuser pawls
524	Replace pressure roller
525	Replace pressure roller pawls
900-905	Key operator calls

Xerox 5345

Код ошибки	Описание
01-01	Frequency monitoring and zero cross problem
01-02	Interlock
01-03	AC power problem
01-04	Finisher interlock
01-05	24v problem
03-01	Optics to main board communication problem
03-02	Software reset problem
03-03	Could be punched holes in the lead edge of the original
03-04	Software problem
03-06	Low battery
03-07	NVM not initialized or is missing or defective
03-17	Communication problem between main board and finisher board
03-18	Initializes one NVM counter to agree to others
03-19	All three NVM counter to agree with others
03-20	Main board/interface board problems
03-21	Problem with RIC NVM
03-22	RIC modem problem
03-23	RIC real time clock failure.
03-25	RIC NVM problem or not initialized
03-27	NVM problem
03-28	Watchdog software problem
03-29	Microprocessor crystal not at correct frequency
03-30	No software response from finisher after 20 seconds have elapsed
06-01	Lens did not reach 1.1 position
06-02	1/2 rate scanner problem
06-03	Scan home problem
06-04	Scan home problem
06-05	Scan home problem
06-06	Scan encoder
06-07	Scan encoder
06-08	Scan drive boost
06-09	Scan encoder
06-11	Scan encoder pulse phases
06-12	Insufficient scan damping
07-01	Duplex tray not home during duplexing
07-02	Tray 2 not home when selected
07-13	Tray 2 height sensor problem
07-15	Tray 2 empty
07-16	Tray 1 door open
07-18	Tray 1 stack sensor
07-22	Tray 1 empty
07-26	Tray 1 bypass switch actuated too long
07-27	Tray 1 bypass switch deactuated too early
07-30	Paper in duplex
07-31	Paper in duplex
07-32	Duplex tray empty, when paper should be there
08-10	Paper did not reach tray 2 input tray sensor
08-11	Paper did not reach duplex input sensor
08-12	Paper did not reach tray 1
08-14	Paper did not leave tray 2 input sensor quickly enough
08-18	Trail edge did not reach tray 2 input sensor quickly enough
08-19	Trail edge did not reach tray 1 input sensor quickly enough
08-20	Paper in duplex
08-21	Paper in tray 2 input
08-22	Paper in tray 2 or duplex at wrong time
08-23	Paper at tray 1 input at wrong time
08-24	Paper in tray 1 at wrong time
08-28	Upper and lower nips problem
09-08	Low toner condition
09-12	Drum signals are out of range
09-13	Unstable drum patch readings
09-15	Patch is too dark
09-16	Patch is too light
09-17	Open toner container access cover
09-18	Low toner level
09-21	Low toner sensor disconnected
09-22	Low toner condition, even after machine has been theoretically, adding toner
10-02	Low fuser temperature
10-03	High fuser temperature
10-06	Paper did not reach out put switch
10-07	Paper stayed on output switch
10-10	Paper did not reach decurler sensor
10-11	Paper did not reach decurler sensor
10-12	Paper on decurler sensor
10-13	Paper did not reach duplex entry sensor in time
10-14	Paper did not reach duplex entry sensor in time
10-15	Paper on entry sensor at wrong time
10-17	Fuser temperature is too high and fuser relay has deactuated
12-01	Paper at finisher input sensor
12-02	Paper did not reach finisher
12-03	Paper reached finisher too soon
12-05	Paper at stapler
12-06	Paper at stapler
12-07	Paper did not reach stapler
12-08	Paper did not reach stapler
12-10	Complied motor not working properly
12-15	Eject motor problem and/or eject encoder
12-20	Stacker motor problem
12-21	Stacker interlock
12-22	Stacker bottom sensor
12-23	Stacker bottom sensor
12-24	Stacker bottom sensor senses full
12-25	Stack height sensor
12-26	Stack height sensor
12-27	Stack height sensor
12-30	Offset home sensor
12-31	Offset home sensor
12-32	OCT switch
12-35	Eject nip carriage
12-36	Eject cam interlock
12-37	Eject nip carriage open timing
12-38	Eject cam interlock
12-40	Tamper motor
12-41	Tamper home problem
12-42	Tamper home sensor
12-43	Staple load sensor
12-44	Tamper home sensor
12-45	Tamper home sensor
12-50	Low on staples
12-51	Stapler home sensor
12-52	Stapler home sensor
12-53	Eject cam interlock
33-37	Too few documents
55-01	RDH interlock switch open during use
55-04	Paper on bypass sensor
55-05	Paper at vacuum timing sensor
55-06	Paper on output sensor
55-10	No paper reached S31
55-20	Paper did not leave S31 at correct time
55-24	Set counter arm problem
55-25	Documents in input tray not detected
55-27	Lead edge did not reach S35 at correct time
55-2955-30	Trail edge did not reach S35 at correct time
55-31	S32, ADF registration sensor did not see paper at correct time
55-32	S32 did not see trail edge at correct time
55-33	S36 One too many documents
55-36	One too many documents
55-39	Hole count problem on document feeder belt
55-40	Document belt travel problem
55-41	Document belt mistracking or skewing
55-45	Paper at inverter sensor
55-47	Inverter sensor did not see paper lead edge at correct time
55-49	More than 50 sheets in input tray
55-50	Right side interlock
55-51	Left side interlock
55-55	Document on glass
93-93	NVM has to be initialized after new software installed

Xerox 5350, 5352

Code	Description
00-009, 030, 031, 032, 033	A door was opened while paper was being fed
00-047	Paper in duplex
00-1	Auditron
00-2	Diagnostic error
00-3	Faults error
00-4	Ric error
00-5	Job manager system error
00-6	LLM interface
00-7	Standby error
00-8	Communications error
00-9	Xerographic error
01-300	Front interlock
01-310	Right upper interlock
01-315	Left upper interlock
01-320	Left lower interlock
01-325	Fuser interlock
02-910	Key counter missing
02-920	Wrong combination of accessories
03-321, 322, 326, 327	LLM to ISIL communications problems
03-328	IOT communications problem with duplex or tray 4
03-330	IOT communications problems with HCF
03-335, 336	LLM communications problems with edit
03-340	NVM memory
03-341-347	Communications problems between IOT and sorter
03-350-354	Communications problem with LLM and user interface
03-363, 364	Communications problem between LLM & optics
03-370-03-373	Communications problem between LLM & DADF
03-380, 384
03-416-422	RAM memory problem
03-424, 426	NVM memory problem
03-430, 432	Billing problem
03-439	GRAIB communications problem
03-440	RIC communications problem
03-441	RIC NVM problem
03-442	Modem
03-443-458	RIC problems
03-460	Serial communications processor problem
04-300	Main motor or drive problem
05-100-108	DADF registration sensor
05-110	DADF exit sensor
05-115, 120	DADF jams
05-305	DADF document drive
05-310, 312	DADF document sensor
05-316	DADF registration sensor jam
05-325	DADF exit sensor
05-335, 341, 345	DADF interlock switches
06-300-310	Scan problems
06-315	Scan drive
06-320A, 320B, 320C, 325	Scan problem
06-330	Lens drive
06-340	Exposure control problem
06-342	LLM CPU problem
06-344-350	Exposure cvontrol problem
06-352	IOT CPU problem
07-300, 315, 330, 345	Tray faults
07-360-370	HCF problems
07-375, 380A, 380B	Duplex problems
08-100-110	Feed problems. Lead edge of copy paper is late getting to feed sensor of tray 1
08-115-162	Feed problem. Lead edge of copy paper is late getting to registration sensor
08-165	Paper jam at registration sensor
08-310-370	Paper at a sensor when power is turned on
08-330	DADF nudger sensor
08-380	Registration side to side problem with home position
08-390	Nip
09-300	Copy cartridge finished (drum unit)
09-310	Add black toner Add color toner
09-320	Add color toner
09-330	Wrong copy cartridge (wrong drum unit)
09-340	Drum cartridge not installed properly
09-350	Waste toner full
100	A fault has occurred
10-100	Exit jam
10-105	Exit jam
10-110	Vertical sensor jam
10-120, 122, 125	Duplex jam
10-150, 155	Too much or not enough paper in duplex tray
10-300	Fuser thermistor
10-302	Low fuser temperature
10-304	Bad fuser temp
10-308	High fuser temperature or open thermistor
10-310	High fuser temperature
10-312	Fuser not up to temperature after energy save
10-314	Fuser problem
10-320	Fuser web finished
10-330, 335, 340	Exit switch, vertical sensor switch actuated when power is turned on
11-100-116	Sorter jam
11-150-176	Sorter auto stapler jam
11-310, 314, 316	Sorter interlock
11-325A,B,C,D,E,F,G	Sorter index
11-352, 354, 356	Sorter auto stapler interlocks
11-365A,B,C,D,E	Sorter auto stapler bin
11-370,371,372A,373A,373B,374	Sorter auto stapler staple failure, staple home problem or tamper home problem
11-385A,385B,390A,B,C,D,E,396A	Sorter auto stapler staple failure, staple home problem or tamper home problem
301	Fuser web must be replaced
302	Copy cartridge (drum unit) must be replaced
501	Tray 1 must be rebuilt
502	Tray 2 must be rebuilt
503	Tray 3 must be rebuilt
504	Tray 4 must be rebuilt
505	HCF must be rebuilt
506	Bypass must be rebuilt
507	Duplex unit must be rebuilt
508	Replace black developer
509	Replace red developer
510	Replace green developer
512	Replace brown developer
513	Copy cartridge (drum unit) will need replacing soon
514	Fuser web will need replacing soon
515	DADF belt should be replaced
516	DADF feed rollers should be replaced
517	Replace exposure lamp
518	Replace suction filter
519	Replace ozone filter
520	Replace optics filter
521	Replace particle filter
522	Replace upper fuser roller
523	Replace fuser pawls
524	Replace pressure roller
525	Replace pressure roller pawls
900-905	Key operator calls

Xerox 5355

Код ошибки	Описание
01-01	Frequency monitoring and zero cross problem
01-02	Interlock
01-03	AC power problem
01-04	Finisher interlock
01-05	24v problem
03-01	Optics to main board communication problem
03-02	Software reset problem
03-03	Could be punched holes in the lead edge of the original
03-04	Software problem
03-06	Low battery
03-07	NVM not initialized or is missing or defective
03-17	Communication problem between main board and finisher board
03-18	Initializes one NVM counter to agree to others
03-19	All three NVM counter to agree with others
03-20	Main board/interface board problems
03-21	Problem with RIC NVM
03-22	RIC modem problem
03-23	RIC real time clock failure.
03-25	RIC NVM problem or not initialized
03-27	NVM problem
03-28	Watchdog software problem
03-29	Microprocessor crystal not at correct frequency
03-30	No software response from finisher after 20 seconds have elapsed
06-01	Lens did not reach 1.1 position
06-02	1/2 rate scanner problem
06-03	Scan home problem
06-04	Scan home problem
06-05	Scan home problem
06-06	Scan encoder
06-07	Scan encoder
06-08	Scan drive boost
06-09	Scan encoder
06-11	Scan encoder pulse phases
06-12	Insufficient scan damping
07-01	Duplex tray not home during duplexing
07-02	Tray 2 not home when selected
07-13	Tray 2 height sensor problem
07-15	Tray 2 empty
07-16	Tray 1 door open
07-18	Tray 1 stack sensor
07-22	Tray 1 empty
07-26	Tray 1 bypass switch actuated too long
07-27	Tray 1 bypass switch deactuated too early
07-30	Paper in duplex
07-31	Paper in duplex
07-32	Duplex tray empty, when paper should be there
08-10	Paper did not reach tray 2 input tray sensor
08-11	Paper did not reach duplex input sensor
08-12	Paper did not reach tray 1
08-14	Paper did not leave tray 2 input sensor quickly enough
08-18	Trail edge did not reach tray 2 input sensor quickly enough
08-19	Trail edge did not reach tray 1 input sensor quickly enough
08-20	Paper in duplex
08-21	Paper in tray 2 input
08-22	Paper in tray 2 or duplex at wrong time
08-23	Paper at tray 1 input at wrong time
08-24	Paper in tray 1 at wrong time
08-28	Upper and lower nips problem
09-08	Low toner condition
09-12	Drum signals are out of range
09-13	Unstable drum patch readings
09-15	Patch is too dark
09-16	Patch is too light
09-17	Open toner container access cover
09-18	Low toner level
09-21	Low toner sensor disconnected
09-22	Low toner condition, even after machine has been theoretically, adding toner
10-02	Low fuser temperature
10-03	High fuser temperature
10-06	Paper did not reach out put switch
10-07	Paper stayed on output switch
10-10	Paper did not reach decurler sensor
10-11	Paper did not reach decurler sensor
10-12	Paper on decurler sensor
10-13	Paper did not reach duplex entry sensor in time
10-14	Paper did not reach duplex entry sensor in time
10-15	Paper on entry sensor at wrong time
10-17	Fuser temperature is too high and fuser relay has deactuated
12-01	Paper at finisher input sensor
12-02	Paper did not reach finisher
12-03	Paper reached finisher too soon
12-05	Paper at stapler
12-06	Paper at stapler
12-07	Paper did not reach stapler
12-08	Paper did not reach stapler
12-10	Complied motor not working properly
12-15	Eject motor problem and/or eject encoder
12-20	Stacker motor problem
12-21	Stacker interlock
12-22	Stacker bottom sensor
12-23	Stacker bottom sensor
12-24	Stacker bottom sensor senses full
12-25	Stack height sensor
12-26	Stack height sensor
12-27	Stack height sensor
12-30	Offset home sensor
12-31	Offset home sensor
12-32	OCT switch
12-35	Eject nip carriage
12-36	Eject cam interlock
12-37	Eject nip carriage open timing
12-38	Eject cam interlock
12-40	Tamper motor
12-41	Tamper home problem
12-42	Tamper home sensor
12-43	Staple load sensor
12-44	Tamper home sensor
12-45	Tamper home sensor
12-50	Low on staples
12-51	Stapler home sensor
12-52	Stapler home sensor
12-53	Eject cam interlock
33-37	Too few documents
55-01	rdh interlock switch open during use
55-04	Paper on bypass sensor
55-05	Paper at vacuum timing sensor
55-06	Paper on output sensor
55-10	No paper reached S31
55-20	Paper did not leave S31 at correct time
55-24	Set counter arm problem
55-25	Documents in input tray not detected
55-27	Lead edge did not reach S35 at correct time
55-2955-30	Trail edge did not reach S35 at correct time
55-31	S32, ADF registration sensor did not see paper at correct time
55-32	S32 did not see trail edge at correct time
55-33	S36 One too many documents
55-36	One too many documents
55-39	Hole count problem on document feeder belt
55-40	Document belt travel problem
55-41	Document belt mistracking or skewing
55-45	Paper at inverter sensor
55-47	Inverter sensor did not see paper lead edge at correct time
55-49	More than 50 sheets in input tray
55-50	Right side interlock
55-51	Left side interlock
55-55	Document on glass
93-93	NVM has to be initialized after new software installed

Xerox XC520, 540, 560, 580

Код ошибки	Описание
H2	Fuser thermistor
H3	Fuser temperature too high. Must be reset in diagnostics
H4	Fuser temperature too low. Must be reset in diagnostics
L3	Scan problem
L4	Min motor drive problem
L8	Exposure lamp not lightning or not enough light reaching auto exposure sensor
P	Paper did not feed

Xerox 5622

Code	Description
A1-1 to A1-32	All indicate a paper path problem, etc. in the ADF
A2	ADF exit problems
A3	Irregular size documents
A5	ADF interlock
A6	ADF single sheet document reset
A7	Platen interlock
A8	ADF exit interlock
C1	Tray 1 jam
C2	Tray 2 jam
C3	Tray 3 jam
C6-1, C6-2	Jams related to duplex
C6-3	Registration sensor, re tray 1
C7-1, C7-2	HCF feed problems
C7-3	Tray 1 feed problem
C8	Paper stays in tray or duplex or HCF
C9	Bypass feed problem
E1-10 to E1-25	Internal jam
E1-6	Paper on registration sensor
E2	Reset signal happened. Might read E-2 something else
E3-30 to E4-14	Exit jam
E3-6	Exit jam
E4-10 to E4-14	Inverter sensor not actuated
E4-15	Inverter sensor
E4-40 to E4-45	Duplex entry sensor
E4-6	Inverter sensor
E5	Front door interlock
E6-1	Tray 1 interlock
E6-2	2 tray or duplex interlock
E6-3	HCF interlock
E7-2, E7-3	Duplex interlock
E8-6 to E8-15	Duplex entry sensor
F1-1	Sorter entry sensor
F1-6	Sorter exit sensor
F3	Paper size not available for sort/stack
F5	Sorter interlock
J1	Add toner
J3	Replace copy cartridge
J7	Replace copy cartridge
J8-1	Wrong copy cartridge installed
J8-2	Copy cartridge EEPROM
L6	Auditron or other counter problem
L8	Platen glass temperature is too high
L9	Communication problem between interimage erase/edge lamps and main board
U1-1	Main motor drive problem
U2-1 to U2-4	Scan home sensor
U3-1	Lens sensor
U4-1	Open fuser thermistor
U4-2	Fuser did not warm up properly
U4-3	Fuser temperature too high
U4-4	Fuser problem. Staying on too long
U4-6	High fuser temperature
U5-1	Sorter bin home switch not activated
U5-2	Sorter bin home switch stayed actuated
U5-3, U5-4	Sorter bin home switch
U6-1	ROM problem
U6-2	RAM problem
U6-3	Low battery
U6-4	Incorrect value in NVM. Reinitialize main board with code 20-96
U8-1 to U8-6	Problem with exposure lamp, lamp sensor, lamp board

Ошибка 016-910 на принтерах Xerox Versalink различных модификаций возникает по причине того, что в лотке отсутствует бумага, совместимая с заданными спецификациями печати.

Параметры используемой бумаги под определенные задачи настраиваются в программе Print Driver PostScript.

Кастомизация включает следующие возможности:

выбор существующих форматов бумаги;
настройка собственного формата (89-320 мм в ширину / 98-1321 мм в высоту);
выбор цвета, типа листа и прочего.

Таким образом, бумага загруженная в лоток подачи должна соответствовать выбранным настройкам. Если принтер определит несоответствие, ошибка 016-910 появится вновь.

Проблема чтения PDF-файла

Аппараты Xerox Versalink часто приостанавливают работу, столкнувшись с проблемой чтения некоторых шрифтов и символов у PDF-файлов. При этом на дисплее высвечивается та же ошибка — 016-910.

Чтобы обойти данную уязвимость, распечатайте документ .pdf как изображение.

Слипшиеся листы

Бумага, предназначенная для печати, может слипнуться, если она определенное время находилась во влажной среде. По этой причине листы не захватываются механизмом принтера, провоцируя возникновение ошибки 016-910.

Выньте бумагу из лотка, оставьте в проветриваемом помещении на несколько часов с целью сушки. Затем возьмите стопку с одной стороны и несколько раз потрясите. Обсохнувшие носители верните в лоток, правильно отрегулировав направляющие длины и ширины.

Остались вопросы? Комментируйте рекомендации или пишите на электронный ящик сервисного центра ТонерДруг!

Коды неисправностей

При сбое во время печати или неисправности аппарата на экран выводится код
неисправности. Если на экране отображается код неисправности, которого нет в
таблице ниже, или неисправность не удается устранить, выполнив указанные далее
действия, обратитесь в сервисный центр Xerox. При отображении кода
неисправности сбрасываются все данные печати на аппарате, а также данные в
его встроенной памяти.

Рекомендуемое решение

Вероятная причина

Код неисправности

Откройте передние дверцы и
убедитесь, что дверца
фьюзера закрыта.
Выключите и снова включите
аппарат.

Выдвижная секция фьюзера
открыта

010 300

Выключите и снова включите
аппарат.

Если неисправность
устранить не удается,
обратитесь в сервисный
центр.

Ошибки скорости ремня
фьюзера

010 310, 010 311, 010 312,

010 313, 010 314, 010 315,
010 316, 010 317, 010 318,

010 319, 010 321, 010 323,

010 324, 010 325, 010 326,

010 327, 010 328, 010 333,

010 334, 010 335, 010 336,

010 337, 010 338, 010 341,

010 342, 010 343, 010 344,

010 347, 010 348, 010 349,

010 350, 010 351, 010 352,

010 353, 010 354, 010 355,

010 356, 010 357, 010 369,

010 370, 010 371, 010 374,

010 379, 010 380, 010 386,

010 387, 010 389

Выключите и снова включите
аппарат.

Если неисправность
устранить не удается,
обратитесь в сервисный
центр.

Ошибка температуры
фьюзера или фьюзер
отключен

010 360, 010 401

10-25

Печатная машина Xerox

Color 800/1000

Руководство пользователя

Устранение неисправностей

Перейти к контенту

Кастомизация включает следующие возможности:

Проблема чтения PDF-файла

Слипшиеся листы

1 комментарий

Ничего не помогло…
Немного потыкав, видимо это у меня генетическое… нашел решение.
Заходим в принтеры, жмем на наш ксерокс, управление, далее свойство принтера
Находим вкладку порты, жмем добавить порт, далее, tcp/ip, прописываем адрес, в моем случае 192.168.1.41 — галочку на только что добавленном порте и применяем.
Пробная печать — Профит

Источники:

https://tonerdrug. ru/oshibka-016-910-na-printerach-xerox-versalink/

This chapter includes:

•

General Troubleshooting…………………………………………………………………………………………………………………………… 184

•

Paper Jams ………………………………………………………………………………………………………………………………………………….. 189

•

Print-Quality Problems ………………………………………………………………………………………………………………………………. 205

•

Copy and Scan Problems …………………………………………………………………………………………………………………………… 212

•

Fax Problems ……………………………………………………………………………………………………………………………………………….. 213

•

Getting Help ………………………………………………………………………………………………………………………………………………… 215

Xerox

VersaLink

C405 Color Multifunction Printer

183

User Guide

Источник

Во время работы с аппаратом могут возникать проблемы, связанные с неисправностями «железа» или ПО. И если расходные материалы можно просто заменить, то с «мозгами» нужно разбираться. Поэтому, для экономии времени и удобства, ниже представлены возможные коды ошибок (FAULT ERROR CODE), которые показывают Xerox DocuColor DC 240/250/242/252/260 и WorkCentre WC 7655/7665/7675/7755/7765/7775 при неисправности, и их значение:

коды ошибок (fault code/error) продолжение. Часть 2

…

061-323 ERROR — RAP No SOS Failure.

061-324 ERROR — RAP No SOS Failure.

061-325 ERROR — RAP No SOS Failure.

061-326 ERROR — RAP ROS Connect Failure Yellow.

061-327 ERROR — RAP ROS Connect Failure.

061-328 ERROR — RAP ROS Connect Failure.

061-329 ERROR — RAP ROS Connect Failure Black.

061-334 ERROR — RAP ROS Y/M VDD Failure.

061-335 ERROR — RAP ROS C/K VDD Failure.

061-336 ERROR — RAP ROS Y/M VDD Down Failure.

061-337 ERROR — RAP ROS C/K VDD Down Failure.

061-338 ERROR — RAP SOS Stop Magenta Failure.

061-339 ERROR — RAP SOS Stop Black Failure.

061-340 ERROR — RAP ROS LD Failure Black.

061-341 ERROR — RAP ROS LD Failure Yellow.

061-342 ERROR — RAP ROS LD Failure Magenta.

061-343 ERROR — RAP ROS LD Failure Cyan.

061-600 ERROR — RAP ROS Data Failure Yellow.

061-601 ERROR — RAP ROS Data Failure Magenta.

061-602 ERROR — RAP ROS Data Failure Cyan.

061-603 ERROR — RAP ROS Data Failure Black.

061-604 ERROR — RAP LD Alarm Yellow.

061-605 ERROR — RAP LD Alarm Magenta.

061-606 ERROR — RAP LD Alarm Cyan.

061-607 ERROR — RAP LD Alarm Black.

062-210 ERROR — RAP IISS Hot Line Failure.

062-211 ERROR — RAP IIT/IPS EEPROM Failure (IPS).

062-220 ERROR — RAP IPS-EXT Connection Failure.

062-277 ERROR — RAP IIT/IPS-DADF Communication Failure.

062-278 ERROR — RAP IIT-Extension Communication Failure.

062-300 ERROR — RAP Platen Interlock Open.

062-310 ERROR — RAP IIT/IPS-ESS Communication Failure.

062-311 ERROR — RAP IIT Software Logic Failure.

062-321 ERROR — RAP IPS-YATA Connection Failure.

062-322 ERROR — RAP EXT-YATA Connection Failure.

062-323 ERROR — RAP YATA PWBA Failure.

062-345 ERROR — RAP IIT/IPS EEPROM Failure (IIT).

062-355 ERROR — RAP IPS Fan Failure.

062-356 ERROR — RAP Lamp Fan Failure.

062-357 ERROR — RAP CCD Fan Failure. An error signal was detected for the CCD fan.

062-360 ERROR — RAP Carriage Position Failure.

062-362 ERROR — RAP X Hard Failure.

062-371 ERROR — RAP Lamp Failure.

062-380 ERROR — RAP Platen AOC Failure.

062-386 ERROR — RAP Platen AOC Failure.

062-389 ERROR — RAP Carriage Over Run (Scan End).

062-392 ERROR — RAP IT/IPS Memory Failure.

062-393 ERROR — RAP IIT/IPS PWB Failure.

062-790 ERROR — RAP X Detect Failure.

063-210 ERROR — RAP Extension EEPROM Failure.

063-220 ERROR — RAP IPS-EXT Psync Failure.

063-230 ERROR — RAP EXT Image Parameter Failure.

063-240 ERROR — RAP EXT Image Parameter Failure.

065-210 ERROR — RAP Extension Page Memory Failure 1.

065-211 ERROR — RAP CIS Shading FROM Failure

065-212 ERROR — RAP CIS Shading Level Failure.

065-213 ERROR — RAP CIS Output Level Failure.

065-215 ERROR — RAP Extension Page Memory Failure 2.

065-216 ERROR — RAP Extension Page Memory Failure 3.

065-219 ERROR — RAP CIS Black White Level Failure.

065-220 ERROR — RAP 1P DUP PWB-EXT Psync Failure.

071-101 ERROR — RAP Feed Out Sensor 1 is not turned ON.

071-104 ERROR — RAP Pre Registration Sensor ON Jam (Tray 1).

071-105 ERROR — RAP Registration Sensor ON Jam (Tray 1).

071-210 ERROR — RAP Tray 1 Lift Up Failure.

072-101 ERROR — RAP Tray 2 Miss Feed Jam.

072-102 ERROR — RAP The Tray 1 Feed Out Sensor does not turn ON.

072-104 ERROR — RAP Pre-Registration Sensor ON Jam (Tray 2).

072-105 ERROR — RAP Registration Sensor ON Jam (Tray 2).

072-210 ERROR — RAP Tray 2 Lift Up Failure.

073-101 ERROR — RAP Tray 3 Miss Feed Jam.

073-102 ERROR — RAP Feed Out Sensor 1 ON Jam (Tray 3).

073-104 ERROR — RAP Pre Registration Sensor ON Jam (Tray 3).

073-105 ERROR — RAP Registration Sensor ON Jam (Tray 3).

073-210 ERROR — RAP Tray 3 Lift Up Failure.

074-101 ERROR — RAP Pre Feed Sensor 4 is not ON within the specified time after the start of feed from Tray 4.

074-102 ERROR — RAP Feed Out Sensor 1 ON Jam (Tray 4).

074-103 ERROR — RAP The Tray 4 Feed Out Sensor is not ON within the specified time for paper fed from Tray 4.

074-104 ERROR — RAP Pre Registration Sensor ON Jam (Tray 4).

074-105 ERROR — RAP Registration Sensor ON Jam (Tray 4).

074-210 ERROR — RAP Tray 4 Lift Up Failure.

075-100 ERROR — RAP Tray 5/Bypass Pre Feed Sensor is not ON within the specified time after the start of feed from Tray 5.

075-101 ERROR — RAP Tray 5/Bypass Feed Out Sensor is not ON within the specified time for paper fed from Tray 5.

075-109 ERROR — RAP Paper from Tray 5/Bypass does not turn ON Pre Regi Sensor within a specified time.

075-135 ERROR — RAP Paper from Tray 5/Bypass does not turn ON Regi Sensor within a specified time.

075-210 ERROR — RAP Tray 5/Bypass Lift Up Sensor does not turn ON within a specified time after Tray 5 begins to lift.

075-211 ERROR — RAP Tray 5/Bypass Lift Down Sensor does not turn ON within a specified time after Tray 5 begins to lower.

077-102 ERROR — RAP Paper from Tray 2 did not turn on the Transport Path Sensor 1 within the specified time.

077-103 ERROR — RAP The Fuser Exit Sensor did not turn off within the specified time in straight exit mode.

077-106 ERROR — RAP The Fuser Exit Sensor did not come on within the specified time after the Registration Motor.

077-107 ERROR — RAP The Fuser Exit Sensor did not turn off within the specified time in invert exit mode.

077-109 ERROR — RAP The IOT Exit Sensor did not come on at the specified time in non-invert mode.

077-111 ERROR — RAP The IOT Exit Sensor did not come on within the specified time in invert exit mode.

077-113 ERROR — RAP The IOT Exit Sensor did not turn off at the specified time in non-invert mode.

077-115 ERROR — RAP The IOT Exit Sensor did not turn off within the specified time in invert exit mode.

077-118 ERROR — RAP Paper from Duplex did not turn on the Pre Regi Sensor within the specified time.

077-120 ERROR — RAP Post 2nd BTR Sensor On JAM.

077-123 ERROR — RAP Duplex In Sensor does not turn ON a spec time after the start of invert.

077-129 ERROR — RAP Paper from Duplex did not turn on the Regi Sensor within the specified time.

077-130 ERROR — RAP Duplex Out Sensor does not turn ON witin a specified time after Duplex In Sensor turns ON.

077-300 ERROR — RAP The Front Cover is open.

077-301 ERROR — RAP The Left Hand Interlock is open.

077-302 ERROR — RAP The Right Hand Cover Interlock is open.

077-303 ERROR — RAP PH Drawer Interlock Open.

077-304 ERROR — RAP The Tray 5/Bypass Cover Interlock is open.

077-312 ERROR — RAP Feeder Communication Failure.

077-909 ERROR — RAP One of the IOT sensors detected paper when power was turned on or when an interlock was closed.

077-967 ERROR — RAP The specified paper type and the paper type being used are different.

077-968 ERROR — RAP The type of paper in the tray was changed.

078-100 ERROR — RAP Paper from Tray 6 does not turn ON Pre Regi Sensor within a specified time.

078-101 ERROR — RAP The Tray 6 Feed Out sensor is not ON within the specified time for paper fed from Tray 6.

078-102 ERROR — RAP Paper from Tray 6 does not turn ON the Regi Sensor within a specified time.

078-151 ERROR — RAP The Tray 6 Feed Out Sensor did not come on within the specified time after the start of feed.

078-250 ERROR — RAP HCF Tray #2 Lift Up Fail.

078-300 ERROR — RAP The HCF transport interlock is open.

078-301 ERROR — RAP HCF Side Out Interlock Open.

089-600 ERROR — RAP Incorrect Fast Scan positioning for the reference color Cyan was detected during fine adjustment.

089-601 ERROR — RAP The Inner MOB Sensor failed to detect the fine-adjustment patterns properly during fine adjustment.

089-602 ERROR — RAP The CENTER MOB Sensor failed to detect the fine-adjustment patterns properly during fine adjustment.

089-603 ERROR — RAP The OUTER MOB Sensor failed to detect the fine-adjustment patterns properly during fine adjustment.

089-604 ERROR — RAP The INNER MOB Sensor failed to detect the rough-adjustment patterns properly during Yellow rough adjustment.

089-605 ERROR — RAP The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Yellow rough adjustment.

089-606 ERROR — RAP The OUTER MOB Sensor failed to detect the rough-adjustment patterns properly during Yellow rough adjustment.

089-607 ERROR — RAP The INNER MOB Sensor failed to detect the rough-adjustment patterns correctly during Magenta rough adjustment.

089-608 ERROR — RAP The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Magenta rough adjustment.

089-609 ERROR — RAP The OUTER MOB Sensor failed to detect the rough-adjustment patterns properly during Magenta rough adjustment.

089-610 ERROR — RAP The INNER MOB Sensor failed to detect the rough-adjustment patterns properly during Cyan rough adjustment.

089-611 ERROR — RAP The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Cyan rough adjustment.

089-612 ERROR — RAP The MOB Sensor OUT failed to detect the rough-adjustment patterns properly during Cyan rough adjustment.

089-613 ERROR — RAP The INNER MOB Sensor failed to detect the rough-adjustment patterns properly during Black rough adjustment.

089-614 ERROR — RAP The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Black rough adjustment.

089-615 ERROR — RAP The MOB Sensor OUT failed to detect the rough-adjustment patterns properly during Black rough adjustment.

089-616 ERROR — RAP RC Data OverFlow Failure.

089-617 ERROR — RAP RC Data OverRange Failure.

091-311 ERROR — RAP The voltage level of the CC cleaner position sensor did not change within the specified time.

091-312 ERROR — RAP Charge (K) Preclean HVPS has failed.

091-313 ERROR — RAP DRUM CRUM ASIC Communication Failure.

091-320 ERROR — RAP Charge Corotron Wire is broken.

091-400 ERROR — RAP The replacement date for Waste Toner Bottle (regular) is near.

091-401 ERROR — RAP The black drum cartridge is near the end-of-life.

091-403 ERROR — RAP The CC Assembly is near the end-of-life.

091-404 ERROR — RAP The CC Assembly has reached the end-of-life.

091-411 ERROR — RAP The yellow drum cartridge is near the end-of-life.

091-421 ERROR — RAP The magenta drum cartridge is near the end-of-life.

091-431 ERROR — RAP The cyan drum cartridge is near the end-of-life.

091-910 ERROR — RAP The waste toner bottle is not present.

091-911 ERROR — RAP The waste toner bottle is full.

091-913 ERROR — RAP The black drum cartridge (K) has reached the end-of-life.

091-914 ERROR — RAP Communication failure between the MCU and the black Drum CRUM.

091-915 ERROR — RAP The MCU detected incorrect data in the black drum cartridge CRUM.

091-916 ERROR — RAP The CRUM authentication registration data on the drum cartridge is incorrect.

091-917 ERROR — RAP MCU cannot communicate with the CRUM in drum Y.

091-918 ERROR — RAP Communication failure with the magenta Drum CRUM.

091-919 ERROR — RAP Communication failure with the cyan Drum CRUM.

091-920 ERROR — RAP The MCU detected incorrect data in the Yellow drum cartridge CRUM.

091-921 ERROR — RAP Drum CRUM is disconnected.

091-922 ERROR — RAP Wrong Data in magenta drum cartridge.

091-923 ERROR — RAP Wrong data in cyan drum cartridge.

091-924 ERROR — RAP The CRUM authentication registration data on the yellow drum cartridge is incorrect.

091-925 ERROR — RAP Wrong data in yellow Magenta cartridge.

091-926 ERROR — RAP The CRUM authentication registration data on the cyan drum cartridge is incorrect.

091-927 ERROR — RAP Yellow Drum CRUM is disconnected.

091-928 ERROR — RAP Magenta Drum CRUM is disconnected.

091-929 ERROR — RAP Cyan Drum CRUM is disconnected.

091-932 ERROR — RAP The yellow drum cartridge (Y) has reached the end-of-life.

091-933 ERROR — RAP The magenta drum cartridge (M) has reached the end-of-life.

091-934 ERROR — RAP The cyan drum cartridge (C) has reached the end-of-life.

092-649 ERROR — RAP The MOB ADC Shutter remains open due to shutter failure.

092-650 ERROR — RAP The MOB ADC Shutter remains closed due to shutter failure.

092-651 ERROR — RAP The output read by ADC Sensor from the clean Photoreceptor surface is out of range.

092-652 ERROR — RAP The measured ADC Patch density is light. (Over 75% of Vclean).

092-653 ERROR — RAP ATC SNR-Yellow output signal failure.

092-654 ERROR — RAP ATC SNR-Magenta output signal failure.

092-655 ERROR — RAP ATC SNR-Cyan output signal failure.

092-656 ERROR — RAP ATC SNR-black output signal failure.

092-657 ERROR — RAP The amplitude of ATC Yellow Sensor output is out of range.

092-658 ERROR — RAP The amplitude of ATC Magenta Sensor output is out of range.

092-659 ERROR — RAP The amplitude of ATC Cyan Sensor output is out of range.

092-660 ERROR — RAP The amplitude of ATC Black Sensor output is out of range.

092-661 ERROR — RAP The temperature output of the environment sensor is out of range.

092-662 ERROR — RAP The humidity output of the environment sensor is out of range.

092-663 ERROR — RAP The two levels of ADC Patch density created in Mini-Setup are reversed.

093-300 ERROR — RAP Marking Drawer Interlock Open.

093-313 ERROR — RAP The Low Toner Sensor failed to detect any toner after the Toner Cartridge Motor was energized.

093-314 ERROR — RAP Yellow Dispense failure.

093-315 ERROR — RAP Magenta Dispense failure.

093-316 ERROR — RAP Cyan Dispense failure.

093-317 ERROR — RAP Black Dispense failure.

093-320 ERROR — RAP There was a problem with the developer motor rotation.

093-421 ERROR — RAP The Black Toner Cartridge (K1) is empty and the Black Toner Cartridge (K2) is near empty.

093-422 ERROR — RAP The Black Toner Cartridge (K2) is empty and the Black Toner Cartridge (K1) is near empty.

093-423 ERROR — RAP Yellow toner is near empty.

093-424 ERROR — RAP Magenta toner is near empty.

093-425 ERROR — RAP Cyan toner empty.

093-600 ERROR — RAP Yellow Dispense near failure.

093-601 ERROR — RAP Magenta Dispense near failure.

093-602 ERROR — RAP Cyan Dispense near failure.

093-603 ERROR — RAP Black Dispense near failure.

093-912 ERROR — RAP The Black Dispense Motor rotation timed out indicating that the Black Cartridge and Reserve Tank are empty.

093-918 ERROR — RAP A communication failure with Black Toner Cartridge CRUM K2.

093-924 ERROR — RAP A communication failure with Black Toner Cartridge CRUM K1.

093-925 ERROR — RAP The data written to the toner CRUM K1 did not agree with the data read.

093-926 ERROR — RAP Toner Cartridge CRUM K1 Authentication Data is different.

093-927 ERROR — RAP A communication failure with Yellow Toner Cartridge CRUM Y.

093-928 ERROR — RAP A communication failure with Magenta Toner Cartridge CRUM M.

093-929 ERROR — RAP A communication failure with Cyan Toner Cartridge CRUM C.

093-932 ERROR — RAP Cartridge Exchange Time Over.

093-934 ERROR — RAP The data written to the toner CRUM M did not agree with the data read.

093-935 ERROR — RAP The data written to the toner CRUM C did not agree with the data read.

093-936 ERROR — RAP The data written to the toner CRUM K2 did not agree with the data read.

093-937 ERROR — RAP Toner Cartridge CRUM Y Authentication Data is different.

093-938 ERROR — RAP Toner Cartridge CRUM M Authentication Data is different.

093-939 ERROR — RAP Toner Cartridge CRUM C Authentication Data is different.

093-940 ERROR — RAP Toner Cartridge CRUM K2 Authentication Data is different.

094-320 ERROR — RAP Retraction was not detected within the specified time after retraction of the 1st BTR started.

094-321 ERROR — RAP First BTR Contact Failure.

094-322 ERROR — RAP Second BTR Retract Failure.

094-323 ERROR — RAP Contact was not detected within the specified time after contact with the 2nd BTR started.

102-356 ERROR — RAP Fatal error related to the EWS.

102-380 ERROR — RAP Fatal error in the MF UI count.

102-381 ERROR — RAP ESS error during communication between ESS and the control panel.

102-382 ERROR — RAP A verification message was not returned from the Control Panel within the specified time.

112-700 ERROR — RAP The punch dust box is full.

116-210 ERROR — RAP Media Reader Fatal Error.

116-211 ERROR — RAP Media Reader Cable disconnected.

116-212 ERROR — RAP [Media Reader] MediaLib SW Logic Failure.

116-310 ERROR — RAP An error was detected while checking ESS font ROM DIMM #1.

116-312 ERROR — RAP An error was detected in the HDD encryption key during activation.

116-313 ERROR — RAP An encryption key was specified but the HDD itself was not encrypted.

116-314 ERROR — RAP An ethernet error was detected.

116-315 ERROR — RAP An error was detected during System Memory 1 R/W.

116-316 ERROR — RAP An error was detected during System Memory 2 R/W.

116-317 ERROR — RAP An error was detected when checking the MF ROM.

116-318 ERROR — RAP An error was detected when checking the expansion ROM R2.

116-321 ERROR — RAP System Software Fatal Error.

116-322 ERROR — RAP WebDAV S/W Failure.

116-323 ERROR — RAP An error was detected during the ESS PWB NVM Read/Write Check.

116-324 ERROR — RAP A fatal software exception error has occurred in the Controller PWB CPU.

116-325 ERROR — RAP An error occurred in ESS fan rotation.

116-329 ERROR — RAP A system call error related to the serial I/F was detected.

116-330 ERROR — RAP Error during HDD check.

116-331 ERROR — RAP An error related to the log was detected.

116-332 ERROR — RAP An error in the MF ROM ( ) was detected.

116-333 ERROR — RAP A problem occurred during software processing, and processing could no longer continue.

116-336 ERROR — RAP Redirector HD Failure. A problem was detected during HD access.

116-337 ERROR — RAP Fatal error with SNTP in general.

116-338 ERROR — RAP Fatal error with JBA in general.

116-340 ERROR — RAP There was insufficient page memory, input buffers, or work area.

116-341 ERROR — RAP Incorrect version or invalid combination ROM DIMMs are installed.

116-342 ERROR — RAP Fatal error related to the SNMP agent.

116-343 ERROR — RAP An IC error within the ESS PWB was detected.

116-346 ERROR — RAP Formatter failure. Error return from a system call.

116-348 ERROR — RAP Redirector failure. Error return from a system call.

116-349 ERROR — RAP There was an error with a call within SIF related to Pflite.

116-350 ERROR — RAP Fatal error with AppleTalk in general.

116-351 ERROR — RAP Fatal error related to EtherTalk.

116-352 ERROR — RAP Fatal error related to NetWare.

116-353 ERROR — RAP A physical problem was detected with the HDD during activation, causing the HDD not to activate.

116-354 ERROR — RAP A problem with the HDD product code was detected during activation.

116-355 ERROR — RAP Fatal error related to the SNMP agent.

116-356 ERROR — RAP The HDD was formatted, but an HDD failure occurred.

116-357 ERROR — RAP PostScript fatal system error.

116-358 ERROR — RAP Fatal error related to the salutation.

116-359 ERROR — RAP Fatal error in PLW.

116-360 ERROR — RAP Fatal error related to SMB.

116-361 ERROR — RAP SPL HDD fatal error. SpoolCont detected an error during HDD access.

116-362 ERROR — RAP SSDP software failure.

116-363 ERROR — RAP BMLinkS or print service software failure.

116-364 ERROR — RAP A timer error was detected.

116-365 ERROR — RAP SPL fatal error.

116-366 ERROR — RAP Report generator incorrect operation.

116-367 ERROR — RAP Parallel fatal error.

116-368 ERROR — RAP DumpPrint fatal error.

116-370 ERROR — RAP XJCL fatal error.

116-371 ERROR — RAP PCL Decomposer Software Failure. PCL fatal error.

116-373 ERROR — RAP Fatal error related to Dynamic DNS.

116-374 ERROR — RAP AutoSW fatal error.

116-376 ERROR — RAP Port 9100 Software Fail.

116-378 ERROR — RAP Fatal error related to MCR.

116-379 ERROR — RAP Fatal error related to MCC.

116-380 ERROR — RAP An error was detected while checking ESS font ROM DIMM #1.

116-381 ERROR — RAP The ABL did not agree with the ABL version information in NVM, or the data was corrupted.

116-382 ERROR — RAP An ABL access to NVM or HDD failed.

116-385 ERROR — RAP Fatal error related to the IDC.

116-388 ERROR — RAP It was detected that no HD is installed.

116-389 ERROR — RAP The system detected that no additional RAM was installed.

116-390 ERROR — RAP A version mismatch was detected between the standard ROM and NVM.

116-391 ERROR — RAP Incorrect specification of the country code, territory code, or paper size group.

116-395 ERROR — RAP Fatal error related to the USB.

116-701 ERROR — RAP Duplex printing is not possible due to insufficient memory.

116-702 ERROR — RAP Printing occurred with a substitute font.

116-703 ERROR — RAP PostScript data problem during PostScript grammar interpretation or language interpretation.

116-704 ERROR — RAP MediaReader No Insert (No Job).

116-705 ERROR — RAP MediaReader Format Error (No Job).

116-706 ERROR — RAP MediaReader: File Attribute Read Error (No Job).

116-707 ERROR — RAP MediaReader: Image File Read Error (No Job).

116-708 ERROR — RAP MediaReader: File Attribute Read Error (In Job).

116-709 ERROR — RAP MediaReader: Image File Read Error (Occurs during job).

116-710 ERROR — RAP Original size not correctly determined.

116-711 ERROR — RAP Mismatch in size and direction or ART EX form with paper to be printed.

116-712 ERROR — RAP PLW form / logo data cannot be registered due to insufficient RAM or HD space.

116-713 ERROR — RAP The job was divided because the HDD was full.

116-714 ERROR — RAP An HP-GL/2 (option) command error occurred.

116-715 ERROR — RAP The form could not be registered because the ART EX form registration upper limit was reached.

116-716 ERROR — RAP MediaReader File Does Not Exist.

116-717 ERROR — RAP MediaLib: Not Execute of New Request.

116-718 ERROR — RAP The specified ART EX form has not been registered.

116-720 ERROR — RAP PCL Memory Low, Page Simplified.

116-737 ERROR — RAP User defined data could not be registered because there was insufficient ART IV user definition memory.

116-738 ERROR — RAP Synthesis problem due to the specified ART IV form size and direction were different from the paper size and direction.

116-739 ERROR — RAP Form / logo data could not be registered because there was insufficient ART IV memory or HDD capacity.

116-740 ERROR — RAP An error occurred because the print data exceeded the printer limit.

116-741 ERROR — RAP No more forms can be registered because the number of ART IV Forms registered has reached the upper limit.

116-742 ERROR — RAP No more logo data can be registered because the number of ART IV log data registered has reached the upper limit.

116-743 ERROR — RAP The form or logo data could not be registered due to insufficient ART IV memory.

116-745 ERROR — RAP An ART IV command error occurred.

116-746 ERROR — RAP The specified form has not been registered.

116-747 ERROR — RAP The paper margin value is too large for the HP-GL/2 (option) effective coordinate area.

116-748 ERROR — RAP The HP-GL/2 (option) print data does not contain any image data.

116-749 ERROR — RAP The specified PostScript font is not in ROM or HDD.

116-771 ERROR — RAP Invalid JBIG Parameter DL Fixed.

116-772 ERROR — RAP Invalid JBIG Parameter D Fixed.

116-773 ERROR — RAP Invalid JBIG Parameter P Fixed.

116-774 ERROR — RAP Invalid JBIG Parameter YD Fixed.

116-775 ERROR — RAP Invalid JBIG Parameter LO Fixed.

116-776 ERROR — RAP Invalid JBIG Parameter MX Fixed.

116-777 ERROR — RAP Invalid JBIG Parameter MY Fixed.

116-778 ERROR — RAP Invalid JBIG Parameter VLENGTH Fixed.

116-780 ERROR — RAP There was a problem with the document attached to the received mail.

116-790 ERROR — RAP Stapling was cancelled.

123-200 ERROR — RAP The data received from ESS exceeded the buffer size of the storage destination within the control panel.

123-201 ERROR — RAP Data intended to be received from the control panel exceeded the buffer size of the storage destination within the control panel.

123-202 ERROR — RAP Events occurred that exceeded the processing capability for requests generated within the control panel.

123-203 ERROR — RAP UI Debug code.

123-204 ERROR — RAP SIO Parameter Failure (UI-Control panel).

123-205 ERROR — RAP SIO Command Failure (UI-Control panel).

123-206 ERROR — RAP SIO Status Failure (UI-Control panel).

123-207 ERROR — RAP Comm Manager Target Failure (UI-Control panel).

123-208 ERROR — RAP Comm Manager Command Failure (UI-Control panel).

123-209 ERROR — RAP EVM Returns Wrong Value (UI-Control panel).

123-310 ERROR — RAP Send Queue Full (UI-Control panel).

123-311 ERROR — RAP Receive Queue Full (UI-Control panel).

123-312 ERROR — RAP EVM Uses Wrong API (UI-Control panel).

123-313 ERROR — RAP AS Uses Wrong API (UI-Control panel).

123-314 ERROR — RAP Event-Waiting Timer Timeout (UI-Control panel).

123-315 ERROR — RAP CTS Internal Failure (UI-Control panel).

123-316 ERROR — RAP Send Request Queue Full SIO (UI-Control panel).

123-317 ERROR — RAP Receive Message Queue Full (UI-Control panel).

123-318 ERROR — RAP Receive Finish Queue Full (UI-Control panel).

123-319 ERROR — RAP Send Failure with No ACK (UI-Control panel).

123-320 ERROR — RAP Polling Failure (UI-Control panel).

123-321 ERROR — RAP Send Message Failure (UI-Control panel).

123-322 ERROR — RAP Target Failure (UI-Control panel).

123-323 ERROR — RAP Address Failure (UI-Control panel). Serial communication error.

123-324 ERROR — RAP Size Failure (UI-Control panel). Serial communication error.

123-325 ERROR — RAP Object Creation Failure (UI-Control panel).

123-326 ERROR — RAP Memory Overflow (UI-Control panel).

123-327 ERROR — RAP Button Overflow (UI-Control panel).

123-328 ERROR — RAP UI Internal Failure with Out of Area.

123-329 ERROR — RAP UI Internal Failure with Invalid Coordinates.

123-330 ERROR — RAP Interface Failure with Invalid Parameter LCD.

123-331 ERROR — RAP UI Internal Failure with Invalid LED Request.

123-332 ERROR — RAP I/F Failure (Invalid Parameter CP).

123-333 ERROR — RAP I/F Failure (No Communication).

123-334 ERROR — RAP I/F Failure (Receiving Error Key Code).

123-335 ERROR — RAP I/F Failure (Receiving Invalid Coordinates).

123-336 ERROR — RAP I/F Failure (DM-ACD Drv. I/F).

123-337 ERROR — RAP Frame Data Error with Invalid Data Type.

123-338 ERROR — RAP Frame Data Error Offset Address Out.

123-339 ERROR — RAP Display Request Code Invalid.

123-340 ERROR — RAP Interface Failure GUAM-DM I/F.

123-341 ERROR — RAP Event Queue Full (UI-Control panel).

123-342 ERROR — RAP Event Queue Empty (UI-Control panel).

123-343 ERROR — RAP Invalid Class (UI-Control panel).

123-344 ERROR — RAP Invalid Type (UI-Control panel).

123-345 ERROR — RAP Timer Queue Full (UI-Control panel).

123-346 ERROR — RAP Invalid Timer Number (UI-Control panel).

123-347 ERROR — RAP Undefined Trap (UI-Control panel).

123-348 ERROR — RAP Command Access Exception (UI-Control panel).

123-349 ERROR — RAP Invalid Command (UI-Control panel).

123-350 ERROR — RAP Privilege Command (UI-Control panel).

123-351 ERROR — RAP No FPU Exception (UI-Control panel).

123-352 ERROR — RAP Address Mis-align (UI-Control panel).

123-353 ERROR — RAP Data Access Exception (UI-Control panel).

123-354 ERROR — RAP Tag Overflow (UI-Control panel).

123-355 ERROR — RAP No Co Processor Exception (UI-Control panel).

123-356 ERROR — RAP Short of Area (UI-Control panel).

123-357 ERROR — RAP Cancel Wait Status (UI-Control panel).

123-358 ERROR — RAP Timeout (UI-Control panel).

123-359 ERROR — RAP Queue Overflow (UI-Control panel).

123-360 ERROR — RAP Context Failure (UI-Control panel).

123-361 ERROR — RAP Object Failure (UI-Control panel).

123-362 ERROR — RAP No Object (UI-Control panel).

123-363 ERROR — RAP Invalid ID (UI-Control panel).

123-364 ERROR — RAP Parameter Failure (UI-Control panel).

123-365 ERROR — RAP Reserve Attribute (UI-Control panel).

123-366 ERROR — RAP Reserve Function Code (UI-Control panel).

123-367 ERROR — RAP Unsupported Function (UI-Control panel).

123-368 ERROR — RAP Short of UI Memory (UI-Control panel).

123-369 ERROR — RAP Invalid Interface Value (UI-Control panel).

123-370 ERROR — RAP Interface Length Failure (UI-Control panel).

123-371 ERROR — RAP Interface Parameter Failure (UI-Control panel).

123-372 ERROR — RAP Interface Sequence Failure (UI-Control panel).

123-373 ERROR — RAP Channel Failure (UI-Control panel).

123-374 ERROR — RAP Invalid User Job ID (UI-Control panel).

123-375 ERROR — RAP Internal Resource Failure (UI-Control panel).

123-376 ERROR — RAP Internal Memory Failure (UI-Control panel).

123-377 ERROR — RAP UI Timer Failure (UI-Control panel).

123-378 ERROR — RAP Interface Format Failure (UI-Control panel).

123-379 ERROR — RAP Dispatch Failure (UI-Control panel).

123-380 ERROR — RAP Copy Interface Failure (UI-Control panel).

123-382 ERROR — RAP Scanner Interface Failure (UI-Control panel).

123-383 ERROR — RAP Report Interface Failure (UI-Control panel).

123-384 ERROR — RAP Server Access Failure (UI-Control panel).

123-385 ERROR — RAP Service Object Overflow (UI-Control panel).

123-386 ERROR — RAP Invalid Service Object (UI-Control panel).

123-387 ERROR — RAP Invalid Service Object Attribute (UI-Control panel).

123-388 ERROR — RAP Attribute Failure (UI-Control panel).

123-389 ERROR — RAP Argument Failure (UI-Control panel).

123-390 ERROR — RAP Job Parameter Failure (UI-Control panel).

123-391 ERROR — RAP Job Actual Parameter Failure (UI-Control panel).

123-392 ERROR — RAP Auditron Failure (UI-Control panel).

123-393 ERROR — RAP EP Failure (UI-Control panel).

123-394 ERROR — RAP File Access Failure (UI-Control panel).

123-395 ERROR — RAP NVM Failure (UI-Control panel).

123-396 ERROR — RAP FF Failure (UI-Control panel).

123-397 ERROR — RAP MGR Failure (UI-Control panel).

123-398 ERROR — RAP Delay Release Queue Full (UI-Control panel).

123-399 ERROR — RAP Internal Failure (UI-Control panel).

123-400 ERROR — RAP Internal Failure (UI-Control panel).

124-310 ERROR — RAP DC132 11 — The product number was not specified.

124-311 ERROR — RAP DC132 09 — The serial number registration field failed.

124-312 ERROR — RAP DC132 12 — Product numbers did not agree.

124-313 ERROR — RAP DC132 10 — Serial numbers did not agree.

124-314 ERROR — RAP DC 132-01 — IOT Speed Failure.

124-315 ERROR — RAP DC 132-02 — IOT Speed Mismatch.

124-316 ERROR — RAP DC 132-04 — Product a/f Model Failure.

124-317 ERROR — RAP DC 132-04 — Product a/f All Product Model Mismatch.

124-318 ERROR — RAP Product Type for S/W Key Failure.

124-319 ERROR — RAP DC 132-08 — All Product Type For S/W Key Mismatch.

124-320 ERROR — RAP EEP ROM Failure.

124-321 ERROR — RAP Backup SRAM Failure. An NVM ROM write problem occurred on the ESS PWB.

124-322 ERROR — RAP DC 132-05 — Copy/Scan/Print S/W Key by PWE Failure.

124-323 ERROR — RAP DC 132-06 — Copy/Scan/Print S/W Key 1 Failure.

124-324 ERROR — RAP All Billings Mismatch.

124-325 ERROR — RAP Billing Restoration Failure.

124-333 ERROR — RAP ASIC Failure (Panther).

124-334 ERROR — RAP Standard Font ROM Error.

124-335 ERROR — RAP Font ROM Not Found.

124-337 ERROR — RAP ESS Standard RAM Error.

124-338 ERROR — RAP Same Font ROMs Found.

124-339 ERROR — RAP ROM DIMM of another product found.

124-340 ERROR — RAP The three CRUM market destination values are not set up (0 or different).

124-341 ERROR — RAP One CRUM market destination value is different (IOT).

124-342 ERROR — RAP One CRUM market destination value is different (SYS 1).

124-343 ERROR — RAP One CRUM market destination value is different (SYS 2).

124-350 ERROR — RAP The three CRUM OEM destination values are not set up (0 or different).

124-351 ERROR — RAP One CRUM OEM destination value is different (IOT).

124-352 ERROR — RAP One CRUM OEM destination value is different (SYS 1).

124-353 ERROR — RAP One CRUM OEM destination value is different (SYS 2).

124-360 ERROR — RAP CRUM Valid/Invalid is not set up at the three locations (0 or different values).

124-361 ERROR — RAP CRUM Validation Failure MCU.

124-362 ERROR — RAP CRUM Validation Failure SYS 1.

124-363 ERROR — RAP CRUM Validation Failure SYS 2.

124-372 ERROR — RAP IOT sc Soft Failure.

124-373 ERROR — RAP IOT Manager SW Failure.

124-374 ERROR — RAP IOT IM Device Driver SW Failure.

124-380 ERROR — RAP CRUM Market fail ALL (2).

124-381 ERROR — RAP CRUM Market fail MCU (2).

124-382 ERROR — RAP CRUM Market fail SYS 1 (2).

124-383 ERROR — RAP CRUM Market fail SYS 2 (2).

124-390 ERROR — RAP CRUM OEM fail ALL (2).

124-391 ERROR — RAP CRUM OEM fail MCU (2).

124-392 ERROR — RAP CRUM OEM fail SYS 1 (2).

124-393 ERROR — RAP CRUM OEM fail SYS 2 (2).

124-701 ERROR — RAP Side Tray to Center Tray.

124-704 ERROR — RAP The output tray was changed from the Folder Tray to the Center Tray and printing continued.

124-705 ERROR — RAP Punching Cancelled.

124-706 ERROR — RAP Folding Cancelled.

124-708 ERROR — RAP The output tray has been changed to the Sub Tray because a failure was detected in the specified output tray.

124-709 ERROR — RAP Stapler Sheet Count is too high.

125-311 ERROR — RAP PSWcont Unexpected Failure.

127-210 ERROR — RAP DFE Communication Failure.

127-211 ERROR — RAP DFE Parameter Error.

127-212 ERROR — RAP ExtPrint Check Mode Error.

127-213 ERROR — RAP External Print IF Mismatch.

127-220 ERROR — RAP Communication Error (video) detected by the DFE.

127-221 ERROR — RAP Communication Error (Command) detected by the DFE.

127-310 ERROR — RAP ESR Task Fatal Error.

127-311 ERROR — RAP ExtPRT.

127-320 ERROR — RAP DFE Critical Failure.

127-337 ERROR — RAP Job Template HDD Write Error.

127-342 ERROR — RAP Job Template Monitor Failure.

127-353 ERROR — RAP LPD Soft Fatal Error.

127-354 ERROR — RAP FTP Server Software Failure.

127-396 ERROR — RAP Mail I/O Soft Fatal error.

127-398 ERROR — RAP IPP Soft Fatal Error.

127-399 ERROR — RAP JME Soft Fatal Error.

202-399 ERROR — RAP Timer Internal Fail.

124 373 xerox error

КОНФЕРЕНЦИЯ СТАРТКОПИ
Принтеры, копировальные аппараты, МФУ, факсы и другая офисная техника:
вопросы ремонта, обслуживания, заправки, выбора

Всем приветю Нужна помощь и совет. Изначально в этом аппарате была вот такая ошибка Xerox wc 5225: Ошибка подачи оригиналов в автоподатчике 005-285. Разобрали автоподатчик- нашли проблему в сломанном флажке и восстановили его. Теперь аппарат выдаёт новую ошибку 124-374 . В интернете нарыли инфу про то что нужно как то переустановить софт на этом аппарате. Не подскажите советом как это сделать? Заранее спасибо.

1. komardin_dima 22.05.15 10:41

софт на данном аппарате переустанавливается с помощью специализированной ксероксовой программой.

2. STRANNIK 22.05.15 11:00

Прошейте аппарат и сделайте полную инициализацию ESS NVM Initialization.
з.ы Лучше отвести спецам которые занимаются исключительно Xerox.

3. Портной Нёма 22.05.15 11:12

(2) На такие машины с такой проблемой нормальные спецы обычно сами выезжают.

(2) те кто непосредственно занимается ксероксами за эту услугу просят . ческих денег))))

5. STRANNIK 22.05.15 12:32

(3)У меня 6 таких машинок,как я устал к ним ездить и лазить по 9 этажному зданию с пылесосом и спец-чемоданчиком,да еще и лифт в этом здании не работает с 2005 года. + еще куча м123 и 118 ксероксов с десяток. мне уже кошмары начинают сниться за неделю до регламентных работ)))
(4)А вы хотите это сделать и ни чего не заработать?

От модератора:

EUREKA doc. # 1099491 Check if there are no blocked sensors in the ADF. To isolate the problem, disconnect ADF from the IIT. Machine should restart and able to make copies. Troubleshoot the ADF for blocked sensors and fix as per documentation.

Источник

124 373 xerox error

Мною был куплен аппарат в нерабочем состоянии. Симптомы по словам продавца были следующие — зависания в процессе печати. Закономерность их происхождения установить не удалось. Приехал ко мне аппарат с ошибкой 117-325, ошибка связана с платой ess nvm pwb, найдена плата от xerox d95 с таким же кодом 960K49212K001, в оригинале стояла K002, в остальном номер совпадает. После перезаливки аппарат начал включатся без ошибок, работает как положено но далее начинается ДЕТЕКТИВ.

1)При отправке задания из нескольких копий или страниц на печать, печатается только первые три копии или страницы. Затем выходит ещё два чистых листа и ошибка:
127-311 RAP
BSD-ON: CH3.7 ESS
ExtPRT
Procedure
This Fault Code may occur in the following situation:
• When the Controller can detect commands but cannot detect input video, data, or clock.
To recover, check cable connections.

Я так и сделал, проверил. И даже отключил все кабели, и отнес их в другую комнату!

2) попробовал снять копии! Ошибка всеравно появляется, хотя контроллер вообще никак не участвует в жизни аппарата

3) ошибка появляется в двух случаях. После третьего листа (неважно копии это или разные страницы одного задания) или в момент окончания задания если задание состоит из трёх листов и менее.

Ошибки которые попадались ещё при экспериментах:
1) 127-311 проверьте соединения
2) 123-354 нет 24 вольта на панели управления (была 1 раз)

24V Power Drop Detected error (UI-Panel). The Control Panel has detected a drop in 24Vpower voltage.Procedure•Turn the power OFF then ON, and then replace the One-Touch Key Module of the MCW-Panel.•Ensure that the customer is programming a job within the parameters of the machine uti-lizing the UI.•Disconnect then reconnect the IIT, UI I/F, ESS, MCU all PWBs connected to them (RAM,Firmware module, EEPROM)•Check the sw version of the controller sw — update if required•Replace UI I/F PWB(PL1.7)•Replace ESS PWB(PL35.2) (If not fixed by this, reinstall the original ESS PWB.)

3) 124-373 была тоже однажды. Не знаю что это

Ещё факты:
1) аппарат почему-то считает своим родным языком французский. И называет себя fuji-xerox на заставке при загрузке
2) Рип FIERY подвесной

Помогите найти виновника. Подскажите направление в котором пробовать искать логику его поведения?

Источник

124 373 xerox error

День добрый!
Поступил данный аппарат, со сгоревшими предохранителями. Заменил предохранители аппарат включился но начал ругаться на печку (код ошибки не помню). Пока искал в инете как сбросить ошибку (включил выключил 2-3 раза) появилась новая ошибка 124-315 (сведение серийных номеров плат). Темы на данном форуме об этом читал. Пишу в надежде, что с тех пор что то изменилось и кто то из магистров снизойдет, что бы таки объяснит как это сделать.
Основной профиль у меня ремонт компьютеров, поэтому в копировальной технике разбираюсь плохо. Ближайший сервисный центр (когда то сертифицированный в xerox) только пожали плечами с круглыми глазами.
Прошу помочь! программаторы паяльные станции имеются
Заранее благодарен!

1. komardin_dima 17.06.15 11:09

Не поверю, что офф сервисный центр ничего не смог сделать.

что нужно сделать:
1) войти в режим чтениязаписи NVM
2) сравните значения в ячейках [700-600],[700-601],[700-602]
3) Если значения разные, то синхронизируйте их
4) Если не помогло то замените MCU и ESS PWB

2. komardin_dima 17.06.15 11:11

на просторах интернета можно найти документацию на данный аппарат. и посмотреть как эта ошибка лечится

3. STRANNIK 17.06.15 16:55

(0)Хм. А лампа светится? Механизм сканирующей линейки двигается?

komardin_dima — большое спасибо за ответ! по поводу «не верю» — сервисный центр «ковчег» город Пятигорск. (официальным сервисным центром сейчас уже не являются). По поводу советов еще раз спасибо буду искать как войти в режим NVM, но если это про то что подержать 0 в течении 5 секунд, то это не срабатывает. в режим не входит. Документацию тоже искал но видно не там. Буду рыть дальше.
STRANNIK — да лампа светится, механизм двигается.

(4) мин через 15 смотрите почту, скидываю СМ

(5) БОЛЬШУЩЕЕ спасибо ! погружаюсь в чтение))

(4) еще раз моя благодарность! все сделал все работает!

Источник

124 373 xerox error

transcend , jetflash 780 , флеш-накопитель , usb 3.0 , флешка

Рейтинг Alexa: #11,726,356 Google PageRank: 0 из 10 Яндекс ТИЦ: 10

Xerox (ксерокс) : продажа оборудования xerox от премьер-партнера в России.

Google PageRank: 0 из 10 Яндекс ТИЦ: 70

Азов-Арсенал партнер компании XEROX в Мариуполе — продажа сервисное обслуживание офисной техники XEROX

Google PageRank: 2 из 10

Xerox (ксерокс) : продажа оборудования xerox от премьер-партнера в России.

Рейтинг Alexa: #7,839,197 Google PageRank: 0 из 10 Яндекс ТИЦ: 50

Google PageRank: 0 из 10 Яндекс ТИЦ: 0

Поставки it оборудования, it решений, программного обеспечения для предприятий и организаций иркутского региона, а так же it аутсорсинг

Рейтинг Alexa: #9,509,363 Google PageRank: 0 из 10 Яндекс ТИЦ: 60

998.ru 998,школа 998,8 998,1 998,код 998,7 998,error 998,new balance 998,ошибка 998,bz 998,998 20,сош 998,pioneer 998,998 номер,998 год,электронный журнал 998,998 20 0,code 998,pl 998,error code 998,998 страна,гоу сош 998,приказ 998,pioneer bz 998,ardo pl.

998.ru 998 , школа 998 , 8 998 , 1 998 , код 998

Google PageRank: 0 из 10 Яндекс ТИЦ: 0

Google PageRank: 3 из 10

программирование, разработка программного обеспечения

программирование , код без ошибок, интерфейсы , шаблоны , процессы ввода

Google PageRank: 0 из 10 Яндекс ТИЦ: 0

Иллюстрированный каталог по продажи техники Xerox, самый полный ассортимент. Возможность онлайн-заказа.

Google PageRank: 0 из 10 Яндекс ТИЦ: 40

Itunes code generator Online 2016 generate itunes gift card codes with a value of $15,$50,$100 Our itunes code generator will be available upon itunes codes availability.

Рейтинг Alexa: #4,841,498 Google PageRank: 0 из 10 Яндекс ТИЦ: 0

Иллюстрированный каталог по продажи техники Xerox, самый полный ассортимент. Возможность онлайн-заказа.

Рейтинг Alexa: #745,490 Google PageRank: 4 из 10

Comment obtenir le code psn gratuit | dernière mise à jour psn générateur de code | Télécharger le code PSN — Code PSN Gratuit

la meilleure façon d’obtenir le code psn gratuit utilisant le réseau PlayStation, Avec le soutien de nos commanditaires, nous donnons code PSN gratuit tous les jours pour de nombreuses personnes.

Google Тренды это диаграмма для отслеживания сезонности ключевых слов. Этот график позволяет лучше понять сезонное изменение полулярности запросов по определенной тематике.

Значения приведены относительно максимума, который принят за 100. Чтобы увидеть более подробную информацию о количестве запросов в определенный момент времени, наведите указатель на график.

Источник

Blog Post

Xerox Error Code Database – With Answers

Hello Hello!
If you have found yourself here, you are probably looking for what one of these error codes means. We have complied the entire list of all the Xerox Error Code here.

This database is ever evolving. Each time we find a solution to one of these error codes, we will write another entry on it and put a link to the code here.

March 2019 Update-
Found this website helping another customer. This has older models with error code searchable –
https://printcopy.info/?l=en&mod=erc&brand=Xerox&page=1

To quickly jump to the code in which the internet brought you here, Hold down CTRL + F , on the keyboard. This will pull up the search window. Type in the code and the screen will shift to that code.

002-770 RAP Insufficient HDD capacity while processing the job template within a job.
03-318 RAP IIT software failure.
03-319 RAP IIT Video Driver Detection Fail. 003-320 RAP IIT-ESS Communication Fail 1.
03-321 RAP IIT-ESS Communication Fail 2.
03-322 RAP IIT-ESS Communication Fail 3.
03-323 RAP IIT-ESS Communication Fail 4.
03-324 RAP IIT-ESS Communication Fail 5.
03-325 RAP IIT-ESS Communication Fail 6.
03-326 RAP IIT-ESS Communication Fail 7.
03-327 RAP IIT-ESS Communication Fail 8.
03-328 RAP IIT-ESS Communication Fail 9.
03-329 RAP IIT-ESS Communication Fail 10.
03-330 RAP IIT-ESS Communication Fail 11.
03-331 RAP IIT-ESS Communication Fail 12.
03-332 RAP IIT-ESS Communication Fail 13.
03-333 RAP IIT-ESS Communication Fail 14.
03-334 RAP IIT-ESS Communication Fail 15.
03-335 RAP IIT-ESS Communication Fail 16.
03-336 RAP IIT-ESS Communication Fail 17.
03-337 RAP IIT-ESS Communication Fail 18.
03-338 RAP IIT-ESS Communication Fail 19.
03-339 RAP IIT-ESS Communication Fail 20.
03-340 RAP IIT-ESS Communication Fail 21.
03-341 RAP IIT-ESS Communication Fail 22.
03-342 RAP IIT-ESS Communication Fail 23.
03-343 RAP IIT-ESS Communication Fail 24.
003-344 RAP Power on hotline failure.
003-345 RAP X PIO Unmatch Fail 1.
003-346 RAP X PIO Unmatch Fail 2.
003-750 RAP Book Duplex-Insufficient Docs.
003-751 RAP Under PANTHER Capacity (Scan).
003-752 RAP This status code is displayed if 600dpi cannot be scanned (DADF).
003-753 RAP This status code is displayed if over 300dpi cannot be scanned (DADF).
003-754 RAP S2X Recoverable Error.
003-755 RAP S2X Command Error.
003-757 RAP This status code is displayed if over 400dpi cannot be scanned (DADF).
003-760 RAP Scan Settings Error.
003-761 RAP Incorrect Paper Tray Size.
003-763 RAP Adjustment Chart Not Found.
003-764 RAP Adjustment Chart Not Found.
003-780 RAP Scan Image Compression Error.
003-795 RAP AMS Limit Error.
003-940 RAP DAM Memory is insufficient.
003-942 RAP Document Size Error.
003-944 RAP Image Repeat Count Fail.
003-946 RAP Copy Vertical/Horizontal Difference (APS).
003-947 RAP Replaced Original Count Error.
003-948 RAP Replaced Original Mismatch.
003-952 RAP Return Documents Color mismatch.
003-955 RAP Documents Size Exchange Error.
003-956 RAP Documents Size Unknown Error.
003-963 RAP No APS Object Tray.
003-965 RAP ATS/APS No Paper. There is no paper in the trays that can be selected with APS.
003-966 RAP AATS/APS No Destination Error.
003-968 RAP Punch Position Error.
003-969 RAP Punch Size Error.
003-972 RAP Maximum Stored Page Over Flow.
003-973 RAP Every Direction Difference.
003-974 RAP Next Original Specification.
003-977 RAP Document Miss Match (Multi Scan).
003-978 RAP Color Document Mismatch (Multi Scan). 003-980 RAP Staple Position Error.
003-981 RAP Staple Size Error.
003-982 RAP IITsc HDD Access Error.
005-121 RAP DADF Feed Sensor ON Jam.
005-122 RAP DADF Simplex/Side 1 Pre Reg Sensor ON Jam.
005-123 RAP DADF Simplex/Side 1 Reg Sensor ON Jam.
005-124 RAP DADF Lead Reg Sensor ON Jam.
005-125 RAP DADF Reg Sensor OFF Jam.
005-126 RAP DADF Out Sensor ON Jam.
005-127 RAP DADF Out Sensor OFF Jam.
005-128 RAP DADF Exit Sensor 1 ON Jam (Simplex Mode).
005-129 RAP DADF Exit Sensor 1 OFF Jam (Simplex Mode).
005-130 RAP DADF Invert Sensor ON Jam (Duplex Mode).
005-131 RAP DADF Invert Sensor On Jam (Inverting).
005-132 RAP DADF Invert SNR on Jam 2.
005-133 RAP DADF Invert Sensor OFF Jam.
005-134 RAP DADF Invert SNR off Jam (Inv).
005-135 RAP DADF Pre Reg Sensor ON Jam (Invert).
005-136 RAP DADF Reg Sensor ON Jam (Invert).
005-137 RAP DADF Exit Sensor 2 ON Jam.
005-138 RAP DADF Exit Sensor 1 ON Jam.
005-139 RAP DADF Invert SNR off Jam.
05-141 RAP DADF Feed Sensor OFF Jam.
05-142 RAP DADF Exit Sensor 1 OFF Jam (Duplex Mode).
005-143 RAP DADF Exit Sensor 2 OFF Jam.
005-144 RAP DADF Too First Pre Reg Sensor ON Jam.
005-145 RAP DADF Reg Sensor Off Jam (Invert).
05-146 RAP DADF Pre Reg Sensor Off Jam.
05-147 RAP DADF Pre Reg Sensor Off Jam (Invert).
005-150 RAP DADF Feed Sensor OFF Jam (Perforated Original Mode).
005-151 RAP DADF Pre Reg Sensor OFF Jam (Perforated Original Mode).
005-152 RAP DADF Reg Sensor OFF Jam (Perforated Original Mode).
005-153 RAP DADF Reg Sensor OFF Jam (Perforated Original Mode).
005-154 RAP DADF Out Sensor OFF Jam (Perforated Original Mode).
005-155 RAP DADF Exit Sensor 1 OFF Jam (Perforated Original Mode) (Simplex).
05-156 RAP DADF Exit Sensor 1 OFF Jam (Perforated Original Mode) (Duplex).
05-157 RAP DADF Invert Sensor OFF Jam (Perforated Original Mode).
005-158 RAP DADF Exit Sensor 2 OFF Jam (Perforated Original Mode).
005-160 RAP DADF Tray Lift Up Fail (Document Set) (Within Job).
005-190 RAP DADF Feed Motor Logic Jam.
005-194 RAP Size Mismatch Jam on Slow Scan Mix Size.
005-195 RAP Size Mismatch Jam on No Mix Size.
005-196 RAP Size Mismatch Jam on No Mix Size.
005-197 RAP Prohibit Combine Size Jam.
005-198 RAP Too Short Size Jam.
005-199 RAP Too Long Size Jam.
005-275 RAP DADF RAM Fail.
005-280 RAP DADF EEPROM Fail.
05-282 RAP DADF Tray Lift Up Fail (No Document).
05-283 RAP DADF Stack Height Sensor Logic Fail.
005-284 RAP DADF APS Sensor Logic Fail.
005-285 RAP DADF Nudger Lift Up Fail.
005-286 RAP DADF Feed Out Sensor Fail.
005-303 RAP DADF Tray Interlock is open.
005-304 RAP Platen Interlock Open.
005-305 RAP DADF Feeder Cover Interlock Open (Run).
005-306 RAP DADF Tray Interlock Open (Run).
005-308 RAP The DADF L/H Cover Interlock is open.
005-309 RAP DADF L/H Cover Interlock Open (Run).
005-906 RAP DADF Feed Sensor Static Jam.
005-907 RAP DADF Pre Reg Sensor Static Jam.
005-908 RAP DADF Reg Sensor Static Jam.
005-909 RAP DADF Lead Reg Sensor Static Jam..
005-910 RAP DADF Out Sensor Static Jam.
005-911 RAP DADF Exit Sensor 1 Static Jam.
005-912 RAP DADF Exit Sensor 2 Static Jam.
005-913 RAP DADF Invert Sensor Static Jam.
005-914 RAP DADF No. 1/2/3 APS Sensor Static Jam.
005-915 RAP DADF No. 1 APS Sensor Static Jam.
005-916 RAP DADF No. 2 APS Sensor Static Jam.
005-917 RAP DADF No. 3 APS Sensor Static Jam.
005-918 RAP DADF Invert Sensor 2 Static Jam.
005-919 RAP DADF Tray Lift Up Fail (Document Set).
005-940 RAP DADF No Original Fail.
005-941 RAP DADF Not Enough Document.
005-942 RAP DADF Tray Stack Over Fail.
010-311 RAP Fuser Heat Roll STS-1 Disconnection Fail. It was detected that fuser heat roll STS-1 disconnected.
010-319 RAP Fuser NC Sensor Differential Amp Fail.
010-320 RAP Heat Roll Over Heat Fail.
10-321 RAP Fuser Nip Fail.
10-322 RAP Fuser NC Center Sensor Disconnection Fail. (Fuser Temperature Sensor Fail).
10-323 RAP Fuser Rear Sensor Disconnection Fail. (Fuser Temperature Sensor Fail).
10-324 RAP Fuser NVM Fail.
010-326 RAP Wait Heat Roll Fuser On Time Fail.
010-327 RAP Standby Heat Roll Fuser On Time Fail.
010-330 RAP Fuser Motor Fail.
010-420 RAP Fuser Assembly Life Near End.
010-421 RAP Fuser Assembly Life End.
012-112 RAP Finisher Interface Entrance Sensor ON.
012-113 RAP Booklet In Sensor ON Jam.
12-114 RAP Booklet In Sensor OFF Jam.
12-115 RAP Booklet Folder Roll Exit Sensor ON Jam.
012-125 RAP Gate Sensor ON JAM: Finisher.
012-132 RAP Finisher Transport Entrance Sensor ON Jam (Long).
012-142 RAP Buffer Path Sensor ON Jam A.
012-151 RAP Compile Exit Sensor OFF Jam.
012-152 RAP Compile Exit Sensor ON Jam A.
012-161 RAP Set Eject Jam.
012-162 RAP Finisher Interface EXIT. Sensor ON Jam.
012-171 RAP Top Tray Exit Sensor ON Jam A.
012-172 RAP Top Tray Exit Sensor OFF Jam A.
012-180 RAP Booklet Folder Roll Exit Sensor OFF Jam.
012-211 RAP Stacker Tray Fail.
012-212 RAP Stacker Tray Upper Limit Fail.
012-213 RAP Stacker Tray Lower Limit Fail.
012-221 RAP Tamper Home Sensor ON Fail.
012-223 RAP Tamper Home Sensor OFF Fail.
012-224 RAP Rear Tamper Home Sensor OFF Fail.
012-225 RAP Booklet Tamper F Home Sensor ON Fail.
012-226 RAP Booklet Tamper F Home Sensor OFF Fail.
012-227 RAP Booklet End Guide Home Sensor OFF Fail.
012-228 RAP Booklet End Guide Home Sensor ON Fail.
012-229 RAP Booklet Tamper R Home Sensor ON Fail.
012-230 RAP Booklet Tamper R Home Sensor OFF Fail.
012-243 RAP Booklet Knife Home Sensor ON Fail.
12-246 RAP Booklet Stapler Fail.
12-247 RAP Side Regi Sensor OFF Fail.
012-260 RAP Eject Clamp Up Sensor ON Fail.
012-261 RAP Booklet Knife Folding SNR Fail.
012-263 RAP Finisher Rear Tamper Home Sensor ON.
012-264 RAP Booklet Drawer Broken Fail.
012-265 RAP Booklet Knife Home Sensor OFF Fail.
012-266 RAP Booklet Compiler No Paper Sensor Fail.
012-270 RAP Top Offset Home Sensor ON Fail: Finisher.
012-271 RAP Top Offset Home Sensor OFF Fail: Finisher.
012-282 RAP Eject Clamp Up Sensor OFF Fail.
012-283 RAP Finisher Set Clamp Home Sensor ON Fail.
012-284 RAP Finisher Set Clamp Home Sensor OFF Fail.
012-291 RAP Stapler Fail.
012-295 RAP Finisher Stapler Move Sensor On Fail.
012-296 RAP Finisher Stapler Move Sensor OFF Fail.
012-300 RAP Finisher Eject Cover Open (Compiler Cover).
012-302 RAP Finisher Front Door Interlock Open.
012-307 RAP Booklet Drawer Set Fail.
012-320 RAP Punch Home Sensor ON Fail.
12-321 RAP Punch Home Sensor OFF Fail.
12-322 RAP Puncher Move Home Sensor OFF Fail.
012-323 RAP Puncher Move Home Sensor On Fail.
012-325 RAP Side Regi Home Sensor On Fail.
012-330 RAP Decurler Cam Home Sensor OFF Fail.
012-332 RAP Decurler Cam Home Sensor ON Fail.
012-334 RAP Download Mode Fail.
012-335 RAP Booklet Sub CPU Communication Fail.
012-900 RAP Buffer Path Sensor Static Jam.
012-901 RAP Finisher Paper Remains at H-Transport Entrance.
012-902 RAP Finisher Paper Remains H-Transport Exit.
012-903 RAP Compile Exit Sensor Static Jam.
012-905 RAP Compile Tray No Paper Sensor Static Jam.
012-907 RAP Top Tray Exit Sensor Static Jam.
012-920 RAP Gate Sensor static JAM (to Top Tray) A: Finisher.
012-932 RAP Gate SNR static JAM (to Stacker Tray) A.
012-934 RAP Gate SNR static JAM (to Stacker Tray) C.
012-935 RAP Finisher Paper Remains at Transport Entrance Sensor.
012-936 RAP Paper Remain at Booklet In SNR A.
012-949 RAP Finisher Punch DustBox Miss Set.
013-902 RAP Booklet Compile No Paper Sensor Static Jam.
013-903 RAP Booklet Folder Roll Exit Sensor Static Jam.
16-210 RAP Software Option Fail (HDD Not Exist).
16-211 RAP Software Option Fail (System Memory Low Volume).
016-212 RAP SW Option Fail (Page Memory Low).
016-213 RAP SW Option Fail (Printer CARD Not Exist).
016-215 RAP SW Option Fail (JPEG Board Not Exist).
16-216 RAP SW Option Fail (Ext Memory Not Exist).
16-217 RAP SW Option Fail (Controller ROM not Printer kit).
16-218 RAP Because PS Kit is not installed, XDOD functions cannot be fulfilled.
16-219 RAP License is required (Printer Kit).
016-220 RAP S2X Unrecoverable Error.
016-221 RAP S2X Communication Error.
016-222 RAP S2X Self-Diag Error.
16-223 RAP SS2X SDRAM Error.
16-224 RAP S2X PCI Reg Error.
16-225 RAP S2X ROM CheckSum Error.
016-226 RAP S2X IIT Connection Error.
016-227 RAP S2X DDR Error.
16-228 RAP S2X Image Processing Error.
16-229 RAP SW Option Fail (FCW-UI Not Exist).
016-311 RAP The scanner was not detected.
16-315 RAP NIIT Interface Fail.
16-316 RAP Page Memory Not Detected.
016-317 RAP Page Memory Broken-Standard.
016-318 RAP Page Memory Broken-Option.
016-320 RAP A fatal error with doc conversion software was detected.
016-322 RAP JBA Account Full.
016-450 RAP SMB Host Name Duplicated.
016-454 RAP DNS Renewal Failure of Dynamic.
016-455 RAP SNTP Server Time Out.
016-456 RAP SNTP Time Asynchronous.
016-503 RAP SMTP Server Address Resolution Fail.
016-504 RAP POP Server Address Resolution Fail.
016-505 RAP POP Authentication Fail.
016-600 RAP KO Authentication Locked.
016-601 RAP Illegal Access Detection.
016-647 RAP With APS selected or with APS set up, there were no trays loaded with paper sizes for Auto Paper Selection.
016-648 RAP Job with Booklet selected was discontinued because it had a cover with an image, a divider, or a blank page.
016-701 RAP Out of ART EX Memory.
016-702 RAP Out of Page Buffer.
016-703 RAP Email to Invalid Box.
016-704 RAP Mailbox is Full.
016-705 RAP Secure Print Fail.
016-706 RAP Max. User Number Exceeded.
016-707 RAP Sample Print Fail.
016-708 RAP HD Full by Annotation/Watermark Image.
016-709 RAP ART EX Command Error.
016-710 RAP Delayed Print Fail.
016-711 RAP Tried to send data whose size is over the system data upper limit.
016-712 RAP Under PANTHER Capacity (I-Formatter).
016-713 RAP Security Box Password Error.
016-714 RAP Security Box is not Enabled.
016-716 RAP TIFF Data Overflow.
016-718 RAP Out of PCL6 Memory.
016-719 RAP Out of PCL Memory.
016-720 RAP PCL Command Error.
016-721 RAP Other Error.
016-722 RAP Job Cancel by Staple Position NG.
016-723 RAP Job Cancel by Punch Position NG.
016-724 RAP Complex Position Error of Staple and Punch.
016-726 RAP PDL Auto Switch Fail.
016-728 RAP Unsupported TIFF Data.
016-729 RAP TIFF Data Size too Big.
016-730 RAP Unsupported ART Command.
016-731 RAP Invalid TIFF Data.
016-732 RAP Form Not Registered.
016-733 RAP Destination Address Resolution Error.
016-734 RAP Simple Transmission report invocation error.
016-735 RAP Updating Job Template.
016-736 RAP Remote directory lock error. Lock directory creation failed.
016-737 RAP Remote lock directory remove error.
016-738 RAP PS Booklet Print Output Paper Size is illegal.
016-739 RAP Mismatch between PS Booklet Doc and Output Paper. 016-740 RAP PS Booklet Output Tray is incorrect.
016-746 RAP Unsupported PDF File.
016-748 RAP HD Full.
016-749 RAP JCL Syntax Error.
016-751 RAP PDF Error.
016-752 RAP PDF Short of Memory.
016-753 RAP PDF Password Mismatched.
016-754 RAP PDF LZW Not Installed.
016-755 RAP PDF Print Prohibited.
016-756 RAP Auditron-Prohibit Service.
016-757 RAP Auditron-Invalid User.
016-758 RAP Auditron-Disabled Function.
016-759 RAP Auditron-Reached Limit.
016-760 RAP PS Decompose Failure.
016-761 RAP FIFO Empty.
016-762 RAP Print LANG Not Installed.
016-764 RAP SMTP Server Connect Error.
016-765 RAP SMTP Server HD Full.
016-766 RAP SMTP Server File System Error.
016-767 RAP Invalid E-mail Address.
016-768 RAP Invalid Sender Address.
016-769 RAP SMTP Server Unsupported DSN.
016-771 RAP Scan Data Repository ERR.
016-772 RAP Scan Data Repository ERR.
016-773 RAP Invalid IP Address.
016-774 RAP HD Full-Compression Convert.
016-775 RAP HD Full-Image Convert.
016-776 RAP Image Convert ERR.
016-777 RAP HD Access ERR-Image Convert.
016-778 RAP HD Full-Scan Image Convert.
016-779 RAP Scan Image Conversion Error.
016-780 RAP HD Access ERR-Image Convert.
016-781 RAP Scan Server Connect ERR.
016-782 RAP Scan Server Login ERR.
016-783 RAP Invalid Server Path.
016-784 RAP Server Write ERR.
016-785 RAP Server HD Full.
016-786 RAP HD Full-Scan Write ERR.
016-787 RAP Invalid Server IP ADD.
016-788 RAP Retrieve to Browser Failed.
016-789 RAP HD Full-Job Memory.
016-791 RAP File Retrieve Fail.
016-792 RAP Specified Job Not Found.
016-793 RAP MF I/O HD Full.
016-794 RAP Media Reader: Media No Insert.
016-795 RAP Media Reader: Format Error.
016-796 RAP Document insert operation error.
016-797 RAP Media Reader: Image File Read Error.
016-798 RAP No Trust Marking Option.
016-799 RAP Print Instruction Fail.
RAP With Duplex Output selected, a size difference between side 1 and side 2 was detected.
RAP With Booklet selected, mixed-in-size/orientation pages with images were detected.
RAP After a duplexed page was deleted, a size difference between side 1 and side 2 was detected.
RAP After a document or divider was inserted, a size difference between side 1 and side 2 was detected.
RAP Documents were merged, including the cover with an image, or a document with a divider.
RAP A document unavailable for duplex print was inserted after a document available for Duplex was inserted.
RAP A document or a divider was inserted after the cover or divider page.
016-949 RAP The user inserted a documnet different in size/orientation from the page to be processed.
016-981 RAP A failure in access to HDD.
016-982 RAP HDD Access Error 2.
016-985 RAP Data Size Over Flow (Scan to Email).
024-340 RAP IOT-ESS Communication Failure 1.
24-341 RAP IOT-ESS Communication Failure 2.
24-342 RAP IOT-ESS Communication Failure 3.
24-343 RAP IOT-ESS Communication Failure 4.
24-345 RAP IOT-ESS Communication Failure 5.
24-346 RAP IOT-ESS Communication Failure 6.
24-347 RAP IOT-ESS Communication Failure 7.
24-348 RAP IOT-ESS Communication Failure 8.
24-349 RAP IOT-ESS Communication Failure 9.
24-350 RAP IOT-ESS Communication Failure 10.
24-351 RAP IOT-ESS Communication Failure 11.
24-352 RAP IOT-ESS Communication Failure 12.
24-353 RAP IOT-ESS Communication Failure 13.
24-354 RAP IOT-ESS Communication Failure 14.
24-355 RAP IOT-ESS Communication Failure 15.
24-356 RAP IOT-ESS Communication Failure 16.
24-357 RAP IOT-ESS Communication Failure 17.
24-358 RAP IOT-ESS Communication Failure 18.
24-359 RAP IOT-ESS Communication Failure 19.
024-360 RAP IOT-ESS Initialization Failure.
024-361 RAP Invalid IOT PaperSizeGroup Information.
024-362 RAP Page Sync Illegal Start.
24-363 RAP Page Sync Illegal Stop.
24-364 RAP DMA Transfer Failure.
24-365 RAP Overflow on the Loop Back Write.
024-366 RAP JBIG Library Other Failure.
024-367 RAP Decompress Other Failure.
024-368 RAP PCI Error.
24-370 RAP Marker Code Detect Failure.
24-371 RAP IOT-ESS Communication Failure 21.
24-372 RAP IOT-ESS Communication Failure 22.
24-373 RAP IOT-ESS Communication Failure 23.
024-374 RAP Regi Con PLL Parameter Failure.
024-375 RAP IOT-ESS Communication Failure 24.
024-600 RAP Billing master counter repair.
024-601 RAP Billing backup counter #1 repair.
024-602 RAP Billing backup counter #2 repair.
024-603 RAP SWKey master counter repair.
024-604 RAP SWKey backup counter #1 repair.
024-605 RAP SWKey backup counter #2 repair.
024-606 RAP Production Number/Serial Number Failure.
024-746 RAP Selected Paper Tray Parameter Mismatch.
024-747 RAP Print Instruction Failure.
RAP Tray 1 Size Mismatch.
RAP Tray 2 Size Mismatch.
RAP Tray 3 Size Mismatch.
RAP Tray 4 Size Mismatch.
RAP Tray 6 Size Mismatch.
RAP Tray 7 Size Mismatch.
024-917 RAP Stacker Tray Staple Set Over Count.
024-919 RAP Face UP Tray Close.
024-920 RAP Face Down Tray 1 Paper FULL.
024-922 RAP Face Down Tray 2 Paper FULL.
024-923 RAP Operation Yellow Toner Empty.
024-924 RAP Operation Magenta Toner Empty.
024-925 RAP Operation Cyan Toner Empty.
024-926 RAP Punch Dust Box Missing Set.
024-927 RAP Offset Catch Tray Full Stack.
024-930 RAP Stacker Tray Full (Small Size Full).
024-934 RAP Paper type mismatch.
024-935 RAP Tray 1 Paper Mismatch.
024-936 RAP Tray 2 Paper Mismatch.
024-937 RAP Tray 3 Paper Mismatch.
024-938 RAP OHP kind Mismatch at Tray 4 (Not White Frame OHP).
024-939 RAP Transparency type mismatch (No white border).
024-940 RAP Folder Tray Out of Place.
024-941 RAP Folder Tray Full Stack.
024-942 RAP Booklet Sheets Over Count.
024-943 RAP Booklet Low Staple.
024-945 RAP Booklet Full Stack.
024-946 RAP Tray 1 Not In Position.
024-947 RAP Tray 2 Not In Position.
024-948 RAP Tray 3 Not In Position.
024-949 RAP Tray 4 Not In Position.
024-950 RAP Tray 1 No Paper.
024-951 RAP Tray 2 No Paper.
024-952 RAP Tray 3 No Paper.
024-953 RAP Tray 4 No Paper.
024-954 RAP MSI No Paper.
024-955 RAP Tray 6 No Paper.
024-956 RAP Tray 7 No Paper.
024-957 RAP Interposer No Paper.
024-958 RAP MSI Size Mismatch.
024-959 RAP Tray 1 Paper Size Mismatch.
024-960 RAP Tray 2 Paper Size Mismatch.
024-961 RAP Tray 3 Paper Size Mismatch.
024-962 RAP Tray 4 Paper Size Mismatch.
024-965 RAP ATS/APS No Paper.
024-966 RAP ATS/APS No Destination Error.
024-967 RAP Different Width Mix Paper Detect (Staple Job).
024-968 RAP Stapler/Punch Batting.
024-969 RAP Different Width Mix Punch.
024-970 RAP Tray 6 Not In Position.
024-971 RAP Tray 7 Not In Position.
024-972 RAP Tray 6 Paper Size Mismatch.
024-973 RAP Tray 7 Paper Size Mismatch.
024-974 RAP Interposer Tray Size Mismatch.
024-975 RAP Booklet Sheets Over Count (Not Field Attachment).
024-976 RAP Finisher Staple Status incorrect.
024-977 RAP Stapler Feed Ready Failure.
024-978 RAP Booklet Stapler incorrect.
024-979 RAP Stapler Near Empty.
024-980 RAP Finisher Stacker Tray Full.
024-981 RAP Finisher Top Tray Full.
024-982 RAP Stacker Lower Safety Warning.
024-983 RAP Booklet Tray Full.
024-984 RAP Booklet Low Staple F.
024-985 RAP SMH Stop Check.
024-987 RAP Envelope Folder Tray Full.
024-988 RAP Envelope Folder Tray Set Failure.
024-989 RAP Booklet Low Staple R.
024-990 RAP Punch Dust Full.
025-596 RAP Diag HDD Failure 1.
025-597 RAP Diag HDD Failure 2.
027-452 RAP Duplicate IP address.
027-500 RAP SMTP Server Address Resolution Failure.
027-501 RAP POP Server Address Resolution Failure.
027-502 RAP POP Authentication Failure.
027-700 RAP Media Failure.
027-701 RAP Media Not Found.
027-702 RAP Media Data Not Found / Not Supported. 027-703 RAP Media Reader Failure / Disconnected.
027-706 RAP Certificate not found. 027-707 RAP Certificate expired.
027-708 RAP Certificate untrusted. 027-709 RAP Certificate revoked.
027-710 RAP S/MIME mail was disabled.
027-711 RAP S/MIME mail sender certificate not found. 027-712 RAP S/MIME mail sender certificate not valid. 027-713 RAP S/MIME mail was altered.
027-714 RAP S/MIME mail sender impersonation. 027-715 RAP S/MIME mail certificate not supported. 027-716 RAP No-Signed mail receipt was rejected.
027-720 RAP Ext Srv. Host Not Found. A server specified for a remote application was not found, or DNS resolution was not possible.
027-721 RAP Ext Srv. Not Found.
027-722 RAP Ext Srv. Timeout Failure.
027-723 RAP Ext Srv. Authentication Failure. 027-724 RAP Ext Srv. Access Failure.
027-725 RAP Ext Srv. Operation Failure. 027-726 RAP Ext Srv. Unknown State.
027-727 RAP Ext Srv. Req Invalid Parameters. 027-728 RAP Ext Srv. Required File Exceeded.
027-737 RAP Template Server Read Error. 027-739 RAP Invalid Template Server Path. 027-740 RAP Template Server Login Error.
027-741 RAP Template Server Connect Failure. 027-742 RAP HD File System Full.
027-743 RAP Template Server Install Error. 027-744 RAP Template Server ADD Error.
027-745 RAP Template Server ADD Error.
027-746 RAP Job Template Pool Server Not Ready. 027-751 RAP Job Template Analysis Error.
027-752 RAP Must User un Inputting.
027-753 RAP Job Flow Service Request Disabled. 027-760 RAP XJT Command Failure.
027-770 RAP PDL Error.
027-771 RAP DFE Disk Full.
027-796 RAP Email Not Printed.
027-797 RAP Invalid Output Destination. 042-313 RAP Rear Cooling Fan Failure.
042-320 RAP Yellow Drum Motor Drive Failure. 042-321 RAP Magenta Drum Motor Drive Failure. 042-322 RAP Cyan Drum Motor Drive Failure.
042-323 RAP Black Drum Motor Drive Failure. 042-324 RAP IBT Drive Motor Failure.
42-325 RAP Main Motor Failure.
42-326 RAP Belt Home Position too long. 042-327 RAP Belt Position Failure.
042-328 RAP Belt Edge Sensor Failure. 042-330 RAP Fuser Exhaust Fan Failure. 042-331 RAP Blower Motor Fan Failure. 042-600 RAP Belt Walk Failure.
042-601 RAP Belt Edge Learn Failure. 042-602 RAP Belt Edge Check Failure.
042-603 RAP Suction Filter Life End Failure. 045-310 RAP Image Ready NG.
045-311 RAP Controller Comm Failure. 045-312 RAP Driver Connect Failure.
047-210 RAP OCT Offset Failure.
047-310 RAP MCU-Finisher Communication Failure. 061-310 RAP Clapper 1 Failure.
061-311 RAP Clapper 2 Failure.
061-313 RAP SOS Long Failure Magenta. 061-315 RAP SOS Long Failure Black.
061-317 RAP SOS Short Failure.
061-319 RAP SOS Short Failure Black. 061-320 RAP Polygon Motor Failure.
061-321 RAP ROS Motor Failure. 061-323 RAP No SOS Failure.
061-324 RAP No SOS Failure. 061-325 RAP No SOS Failure.
061-326 RAP ROS Connect Failure Yellow. 061-327 RAP ROS Connect Failure.
61-328 RAP ROS Connect Failure.
61-329 RAP ROS Connect Failure Black. 061-334 RAP ROS Y/M VDD Failure.
61-335 RAP ROS C/K VDD Failure.
61-336 RAP ROS Y/M VDD Down Failure.
61-337 RAP ROS C/K VDD Down Failure. 061-338 RAP SOS Stop Magenta Failure. 061-339 RAP SOS Stop Black Failure.
061-340 RAP ROS LD Failure Black. 061-341 RAP ROS LD Failure Yellow. 061-342 RAP ROS LD Failure Magenta. 061-343 RAP ROS LD Failure Cyan.
061-600 RAP ROS Data Failure Yellow. 061-601 RAP ROS Data Failure Magenta. 061-602 RAP ROS Data Failure Cyan.
061-603 RAP ROS Data Failure Black. 061-604 RAP LD Alarm Yellow.
061-605 RAP LD Alarm Magenta. 061-606 RAP LD Alarm Cyan.
061-607 RAP LD Alarm Black.
62-210 RAP IISS Hot Line Failure.
62-211 RAP IIT/IPS EEPROM Failure (IPS).
062-220 RAP IPS-EXT Connection Failure.
062-277 RAP IIT/IPS-DADF Communication Failure. 062-278 RAP IIT-Extension Communication Failure. 062-300 RAP Platen Interlock Open.
062-310 RAP IIT/IPS-ESS Communication Failure. 062-311 RAP IIT Software Logic Failure.
62-321 RAP IPS-YATA Connection Failure.
62-322 RAP EXT-YATA Connection Failure. 062-323 RAP YATA PWBA Failure.
062-345 RAP IIT/IPS EEPROM Failure (IIT).
062-355 RAP IPS Fan Failure. 062-356 RAP Lamp Fan Failure.
062-357 RAP CCD Fan Failure. An error signal was detected for the CCD fan.
062-360 RAP Carriage Position Failure. 062-362 RAP X Hard Failure.
062-371 RAP Lamp Failure.
062-380 RAP Platen AOC Failure. 062-386 RAP Platen AOC Failure.
062-389 RAP Carriage Over Run (Scan End). 062-392 RAP IT/IPS Memory Failure.
062-393 RAP IIT/IPS PWB Failure.
062-790 RAP X Detect Failure.
063-210 RAP Extension EEPROM Failure. 063-220 RAP IPS-EXT Psync Failure.
063-230 RAP EXT Image Parameter Failure. 063-240 RAP EXT Image Parameter Failure. 065-210 RAP Extension Page Memory Failure 1. 065-211 RAP CIS Shading FROM Failure
065-212 RAP CIS Shading Level Failure. 065-213 RAP CIS Output Level Failure.
065-215 RAP Extension Page Memory Failure 2. 065-216 RAP Extension Page Memory Failure 3. 065-219 RAP CIS Black White Level Failure.
065-220 RAP 1P DUP PWB-EXT Psync Failure.
071-101 RAP Feed Out Sensor 1 is not turned ON.
071-104 RAP Pre Registration Sensor ON Jam (Tray 1). 071-105 RAP Registration Sensor ON Jam (Tray 1).
071-210 RAP Tray 1 Lift Up Failure. 072-101 RAP Tray 2 Miss Feed Jam.
072-102 RAP The Tray 1 Feed Out Sensor does not turn ON. 072-104 RAP Pre-Registration Sensor ON Jam (Tray 2).
072-105 RAP Registration Sensor ON Jam (Tray 2). 072-210 RAP Tray 2 Lift Up Failure.
73-101 RAP Tray 3 Miss Feed Jam.
73-102 RAP Feed Out Sensor 1 ON Jam (Tray 3).
73-104 RAP Pre Registration Sensor ON Jam (Tray 3).
73-105 RAP Registration Sensor ON Jam (Tray 3). 073-210 RAP Tray 3 Lift Up Failure.
74-101 RAP Pre Feed Sensor 4 is not ON within the specified time after the start of feed from Tray 4.
74-102 RAP Feed Out Sensor 1 ON Jam (Tray 4).
74-103 RAP The Tray 4 Feed Out Sensor is not ON within the specified time for paper fed from Tray 4.
74-104 RAP Pre Registration Sensor ON Jam (Tray 4). 074-105 RAP Registration Sensor ON Jam (Tray 4).
074-210 RAP Tray 4 Lift Up Failure.
75-100 RAP Tray 5/Bypass Pre Feed Sensor is not ON within the specified time after the start of feed from Tray 5.
75-101 RAP Tray 5/Bypass Feed Out Sensor is not ON within the specified time for paper fed from Tray 5.
075-109 RAP Paper from Tray 5/Bypass does not turn ON Pre Regi Sensor within a specified time.
075-135 RAP Paper from Tray 5/Bypass does not turn ON Regi Sensor within a specified time.
75-210 RAP Tray 5/Bypass Lift Up Sensor does not turn ON within a specified time after Tray 5 begins to lift.
75-211 RAP Tray 5/Bypass Lift Down Sensor does not turn ON within a specified time after Tray 5 begins to lower.
77-102 RAP Paper from Tray 2 did not turn on the Transport Path Sensor 1 within the specified time.
77-103 RAP The Fuser Exit Sensor did not turn off within the specified time in straight exit mode.
77-106 RAP The Fuser Exit Sensor did not come on within the specified time after the Registration Motor.
77-107 RAP The Fuser Exit Sensor did not turn off within the specified time in invert exit mode.
077-109 RAP The IOT Exit Sensor did not come on at the specified time in non-invert mode.
077-111 RAP The IOT Exit Sensor did not come on within the specified time in invert exit mode.
077-113 RAP The IOT Exit Sensor did not turn off at the specified time in non-invert mode.
077-115 RAP The IOT Exit Sensor did not turn off within the specified time in invert exit mode.
077-118 RAP Paper from Duplex did not turn on the Pre Regi Sensor within the specified time.
077-120 RAP Post 2nd BTR Sensor On JAM.
077-123 RAP Duplex In Sensor does not turn ON a spec time after the start of invert.
77-129 RAP Paper from Duplex did not turn on the Regi Sensor within the specified time.
77-130 RAP Duplex Out Sensor does not turn ON witin a specified time after Duplex In Sensor turns ON.
77-300 RAP The Front Cover is open.
77-301 RAP The Left Hand Interlock is open.
77-302 RAP The Right Hand Cover Interlock is open. 077-303 RAP PH Drawer Interlock Open.
077-304 RAP The Tray 5/Bypass Cover Interlock is open. 077-312 RAP Feeder Communication Failure.
077-909 RAP One of the IOT sensors detected paper when power was turned on or when an interlock was closed.
077-967 RAP The specified paper type and the paper type being used are different.
077-968 RAP The type of paper in the tray was changed.
78-100 RAP Paper from Tray 6 does not turn ON Pre Regi Sensor within a specified time.
78-101 RAP The Tray 6 Feed Out sensor is not ON within the specified time for paper fed from Tray 6.
78-102 RAP Paper from Tray 6 does not turn ON the Regi Sensor within a specified time.
078-151 RAP The Tray 6 Feed Out Sensor did not come on within the specified time after the start of feed.
078-250 RAP HCF Tray #2 Lift Up Fail.
078-300 RAP The HCF transport interlock is open. 078-301 RAP HCF Side Out Interlock Open.
089-600 RAP Incorrect Fast Scan positioning for the reference color Cyan was detected during fine adjustment.
089-601 RAP The Inner MOB Sensor failed to detect the fine-adjustment patterns properly during fine adjustment.
089-602 RAP The CENTER MOB Sensor failed to detect the fine-adjustment patterns properly during fine adjustment.
089-603 RAP The OUTER MOB Sensor failed to detect the fine-adjustment patterns properly during fine adjustment.
089-604 RAP The INNER MOB Sensor failed to detect the rough-adjustment patterns properly during Yellow rough adjustment.
089-605 RAP The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Yellow rough adjustment.
089-606 RAP The OUTER MOB Sensor failed to detect the rough-adjustment patterns properly during Yellow rough adjustment.
089-607 RAP The INNER MOB Sensor failed to detect the rough-adjustment patterns correctly during Magenta rough adjustment.
089-608 RAP The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Magenta rough adjustment.
089-609 RAP The OUTER MOB Sensor failed to detect the rough-adjustment patterns properly during Magenta rough adjustment.
089-610 RAP The INNER MOB Sensor failed to detect the rough-adjustment patterns properly during Cyan rough adjustment.
089-611 RAP The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Cyan rough adjustment.
089-612 RAP The MOB Sensor OUT failed to detect the rough-adjustment patterns properly during Cyan rough adjustment.
089-613 RAP The INNER MOB Sensor failed to detect the rough-adjustment patterns properly during Black rough adjustment.
089-614 RAP The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Black rough adjustment.
089-615 RAP The MOB Sensor OUT failed to detect the rough-adjustment patterns properly during Black rough adjustment.
089-616 RAP RC Data OverFlow Failure.
089-617 RAP RC Data OverRange Failure.
91-311 RAP The voltage level of the CC cleaner position sensor did not change within the specified time.
91-312 RAP Charge (K) Preclean HVPS has failed.
91-313 RAP DRUM CRUM ASIC Communication Failure.
091-320 RAP Charge Corotron Wire is broken.
91-400 RAP The replacement date for Waste Toner Bottle (regular) is near.
91-401 RAP The black drum cartridge is near the end-of-life.
091-403 RAP The CC Assembly is near the end-of-life.
091-404 RAP The CC Assembly has reached the end-of-life.
091-411 RAP The yellow drum cartridge is near the end-of-life.
091-421 RAP The magenta drum cartridge is near the end-of-life.
091-431 RAP The cyan drum cartridge is near the end-of-life.
091-910 RAP The waste toner bottle is not present.
091-911 RAP The waste toner bottle is full.
091-913 RAP The black drum cartridge (K) has reached the end-of-life.
091-914 RAP Communication failure between the MCU and the black Drum CRUM.
091-915 RAP The MCU detected incorrect data in the black drum cartridge CRUM.
091-916 RAP The CRUM authentication registration data on the drum cartridge is incorrect.
091-917 RAP MCU cannot communicate with the CRUM in drum Y.
091-918 RAP Communication failure with the magenta Drum CRUM.
091-919 RAP Communication failure with the cyan Drum CRUM.
091-920 RAP The MCU detected incorrect data in the Yellow drum cartridge CRUM.
091-921 RAP Drum CRUM is disconnected.
091-922 RAP Wrong Data in magenta drum cartridge.
091-923 RAP Wrong data in cyan drum cartridge.
091-924 RAP The CRUM authentication registration data on the yellow drum cartridge is incorrect.
091-925 RAP Wrong data in yellow Magenta cartridge.
091-926 RAP The CRUM authentication registration data on the cyan drum cartridge is incorrect.
091-927 RAP Yellow Drum CRUM is disconnected.
091-928 RAP Magenta Drum CRUM is disconnected.
091-929 RAP Cyan Drum CRUM is disconnected.
091-932 RAP The yellow drum cartridge (Y) has reached the end-of-life.
091-933 RAP The magenta drum cartridge (M) has reached the end-of-life.
091-934 RAP The cyan drum cartridge (C) has reached the end-of-life.
092-649 RAP The MOB ADC Shutter remains open due to shutter failure.
092-650 RAP The MOB ADC Shutter remains closed due to shutter failure.
092-651 RAP The output read by ADC Sensor from the clean Photoreceptor surface is out of range.
092-652 RAP The measured ADC Patch density is light. (Over 75% of Vclean).
092-653 RAP ATC SNR-Yellow output signal failure.
092-654 RAP ATC SNR-Magenta output signal failure.
092-655 RAP ATC SNR-Cyan output signal failure.
092-656 RAP ATC SNR-black output signal failure.
RAP The amplitude of ATC Yellow Sensor output is out of range.
RAP The amplitude of ATC Magenta Sensor output is out of range.
RAP The amplitude of ATC Cyan Sensor output is out of range.
RAP The amplitude of ATC Black Sensor output is out of range.
RAP The temperature output of the environment sensor is out of range.
RAP The humidity output of the environment sensor is out of range.
RAP The two levels of ADC Patch density created in Mini-Setup are reversed.
093-300 RAP Marking Drawer Interlock Open.
93-313 RAP The Low Toner Sensor failed to detect any toner after the Toner Cartridge Motor was energized.
93-314 RAP Yellow Dispense failure. 093-315 RAP Magenta Dispense failure.
093-316 RAP Cyan Dispense failure.
093-317 RAP Black Dispense failure.
093-320 RAP There was a problem with the developer motor rotation.
093-421 RAP The Black Toner Cartridge (K1) is empty and the Black Toner Cartridge (K2) is near empty.
093-422 RAP The Black Toner Cartridge (K2) is empty and the Black Toner Cartridge (K1) is near empty.
093-423 RAP Yellow toner is near empty.
093-424 RAP Magenta toner is near empty.
093-425 RAP Cyan toner empty.
093-600 RAP Yellow Dispense near failure.
093-601 RAP Magenta Dispense near failure.
093-602 RAP Cyan Dispense near failure.
093-603 RAP Black Dispense near failure.
093-912 RAP The Black Dispense Motor rotation timed out indicating that the Black Cartridge and Reserve Tank are empty.
093-918 RAP A communication failure with Black Toner Cartridge CRUM K2.
RAP A communication failure with Black Toner Cartridge CRUM K1.
RAP The data written to the toner CRUM K1 did not agree with the data read.
RAP Toner Cartridge CRUM K1 Authentication Data is different.
RAP A communication failure with Yellow Toner Cartridge CRUM Y.
RAP A communication failure with Magenta Toner Cartridge CRUM M.
RAP A communication failure with Cyan Toner Cartridge CRUM C.
093-932 RAP Cartridge Exchange Time Over.
093-934 RAP The data written to the toner CRUM M did not agree with the data read.
093-935 RAP The data written to the toner CRUM C did not agree with the data read.
093-936 RAP The data written to the toner CRUM K2 did not agree with the data read.
093-937 RAP Toner Cartridge CRUM Y Authentication Data is different.
093-938 RAP Toner Cartridge CRUM M Authentication Data is different.
093-939 RAP Toner Cartridge CRUM C Authentication Data is different.
093-940 RAP Toner Cartridge CRUM K2 Authentication Data is different.
94-320 RAP Retraction was not detected within the specified time after retraction of the 1st BTR started.
94-321 RAP First BTR Contact Failure.
094-322 RAP Second BTR Retract Failure.
094-323 RAP Contact was not detected within the specified time after contact with the 2nd BTR started.

Looking for a new Xerox that works?
Check out this beauty – Altalink C8030

USA Copier Lease is an exclusive Xerox dealer with clients across the United States. We can service and support your Xerox devices anywhere in the United States with a guaranteed same day / next day on-site service guarantee.

Источник

Thanks Thanks: 0

Likes Likes: 0

Dislikes: 0

02-25-2013

#1

Service Manager

1,000+ Posts

Rep Power

46

WC 5225 with software error 124-373

Getting software error 124-373. Would replacing one of the DDR Dimm cards solve this problem? Don’t have in stock or would try it. I guess i could remove to see if error disappears and just get less features. Please advise. Your help is appreciated very much. Frank/ActionPhotocopy
02-26-2013

#2

Senior Tech

250+ Posts

Rep Power

34

Re: WC 5225 with software error 124-373

-Try to power up printer without drum cartridge,and with left door open.
-Check all the interlock switches.
-Could be defective drum cartrige.
-IOT NVM initilisation may be needed.
03-02-2013

#3

Service Manager

1,000+ Posts

Rep Power

46

Re: WC 5225 with software error 124-373

Thank you Mitja. I swapped the drum and still had 124-373 but I did not put new drum. The door switches are okay.

I have 2 machine on my premises and one originally had the 124-373 code and the other 5225 was supposed to be network ready but was missing the 3 cards on the ESS PWB and only offered only copy mode. I received the 3 card and swapped the DDR DIMM #1 card to see if that was problem and got 124-374. Then I swapped back and got long warmup with 116-399 (over ten minute initialization)
Please advise as I have a customer for one of the machines and potential customer for the other. Iam not sure how to do the IOT NVM Initialization but will look it up in service manual. I am totally ignorant on computer connectivity , firmware, software etc and need to learn. Frank

PS When I checked the 2nd machine which had the other machine’s drum there was a message saying to please order the drum.
03-04-2013

#4

Senior Tech

250+ Posts

Rep Power

34

Re: WC 5225 with software error 124-373
03-04-2013

#5

Service Manager

1,000+ Posts

Rep Power

46

Re: WC 5225 with software error 124-373

Thanks Mitja. I will post results. Frank