Проверить вентилятор на предмет загрязнений.
Убедиться, что ничего не блокирует воздушный поток.
Проверить разъем подключения вентилятора и его правильность подключения.
Проверить вентилятор на другом асике.
Заменить вентилятор.
Замените блок питания.
Почистить асик от различного рода загрязнений.
Проверить температуры входящего потока.
Заменить вентиляторы на оригинальные.
Перепрошить асик через сд карту, а потом через WhatsMinerTool.
Заменить блок питания.
Перезапустить асик.
Попробовать поменять розетку/фазу.
Заменить блок питания.
Почистить асик от различного рода загрязнений.
Заменить термоинтерфейс.
Сделать оружающую среду более холодной.
Проверьте напряжение в сети.
Попробовать поменять розетку/фазу.
Попробовать поменять розетку/фазу.
Выключить асик минут на 10, после попробовать еще раз.
Сделать оружающую среду более холодной.
Проверить температуру окружающей среды.
Выключить асик минут на 10, после попробовать еще раз.
Сделать оружающую среду более холодной.
Проверить напряжение в сети.
Выключить асик минут на 10, после попробовать еще раз.
Сделать оружающую среду более холодной.
Проверить напряжение в сети.
Выключить асик минут на 10, после попробовать еще раз.
Попробовать поменять розетку/фазу.
Может происходить из-за:
1) Слишком большая нагрузка на сеть/фазу
2) Не справляется стабилизатор напряжения (если он есть)
3) Стоит релейный стабилизатор напряжения, из-за его конструкции у него кратковременно просаживается напряжение, для блока питания этого времени хватает, чтобы уйти в защиту.
Выключить асик минут на 10, после попробовать еще раз.
Сделать оружающую среду более холодной.
Для оптимальной работы блока питания ему нужно 220~230 Вольт стабильного напряжения.
Попробовать поменять розетку/фазу.
Заменить вентилятор блока питания
Заменить блок питания.
Выключить асик минут на 10, после попробовать еще раз.
Сделать оружающую среду более холодной.
Заменить блок питания.
Проверьте шлейф подключения блока птания к КПУ.
Замените блок питания.
Проверьте затяжку винтов шины питания.
Проверьте соединения на предмет короткого замыкания.
Сделать оружающую среду более холодной.
Проверить напряжение в сети.
Выключить асик минут на 10, после попробовать еще раз.
Попробовать поменять розетку/фазу.
Заменить блок питания.
Проверьте затяжку винтов шины питания.
Сделать оружающую среду более холодной.
Заменить вентилятор блока питания.
Проверить температуру окружающей среды.
Выключить асик минут на 10, после попробовать еще раз.
Сделать оружающую среду более холодной.
Поменять две платы местами, если ошибка последует за платой, то плату в ремонт.
Замените контрольную плату.
Замените блок питания.
Проверить температуру окружающей среды.
Сделать оружающую среду более холодной.
Замените термоинтерфейс плат.
Проверить адаптер плат и его шлейф.
Проверить затяжку винтов шины питания.
Попробовать заменить КПУ.
Попробовать заменить блок питания.
Перепрошить асик через sd-карту, потом через WhatsMinerTool.
Замените хеш плату на подходящую.
Проверить подключение шлейфа адаптера плат к КПУ.
Попробовать поменять КПУ на новую, если ошибка пропала, то КПУ в ремонт.
Поменять две платы местами, если ошибка ушла за платой, то плату в ремонт.
Проверить подключение шлейфа адаптера плат к КПУ.
Поменять две платы местами, если ошибка ушла за платой, то плату в ремонт.
Проверить подключение шлейфа адаптера плат к КПУ.
Проверить параметры разгона.
Проверить напряжение в сети.
Поменять две платы местами, если ошибка ушла за платой, то плату в ремонт.
Данная ошибка может появляться при иммерсионном охлаждение из-за расположения датчика температуры.
Для иммерсионого охлаждения можно перевернуть асик, таким образом датчик температуры будет в более холодном месте.
Проверить температуру окружающей среды.
Сделать окружающую среду более холодной.
Проверьте температуру окружающей среды.
Сделать окружающую среды более холодной.
Проверить затяжку винтов на шине питания.
Попробовать заменить КПУ.
Проверить интернет.
Проверить настройки пулов.
Попробовать поменять пул.
Попробовать поменять провайдера (даже если другие устройства работают хорошо).
Проверить интернет на предмет обрывов соединения.
Проверить температуру окружающей среды, плат и чипов.
Перепрошить асик через sd-карту, потом через WhatsMinerTool.
После включить обратно, если ошибка будет повторяться, то блок питания в ремонт.
Проверьте напряжение в сети.
Замените блок питания.
После включить обратно, если ошибка будет повторяться, то блок питания в ремонт.
Ремонт блока питания.
Код
Название
Описание и способ устранения ошибки
110
Ошибка обнаружения оборотов вентилятора на входе
Не оригинальные или восстановленные вентиляторы могут не выдавать нужных оборотов или изначально быть не рабочими. Рекомендуем заменить их на оригинальные, чтобы исключить возможные проблемы.
Проверить вентилятор на предмет загрязнений.
Убедиться, что ничего не блокирует воздушный поток.
Проверить разъем подключения вентилятора и его правильность подключения.
Проверить вентилятор на другом асике.
Заменить вентилятор.
Замените блок питания.
111
Ошибка обнаружения оборотов вентилятора на выходе
120
Ошибка оборотов вентилятора на входе (Отклонение 2000+)
121
Ошибка оборотов вентилятора на выходе (Отклонение 2000+)
130
Ошибка оборотов вентилятора на входе (Отклонение 3000+)
131
Ошибка оборотов вентилятора на выходе (Отклонение 3000+)
140
Слишком высокие обороты вентиляторов
Из-за высокой температуры асик пытается себя охладить увеличением оборотов вентиляторов.
Почистить асик от различного рода загрязнений.
Проверить температуры входящего потока.
Заменить вентиляторы на оригинальные.
200
Ошибка. Отсутствие напряжения с блока питания
Проверьте кабель подключения асика к сети.
Перепрошить асик через сд карту, а потом через WhatsMinerTool.
Заменить блок питания.
201
Несоответствие модели блока питания и файла конфигурации
202
Ошибка выходного напряжения с блока питания
Проверить напряжение в сети.
Перезапустить асик.
Попробовать поменять розетку/фазу.
Заменить блок питания.
203
Защита блока питания от перегрузки
Проверить температуру потока воздуха.
Почистить асик от различного рода загрязнений.
Заменить термоинтерфейс.
Сделать оружающую среду более холодной.
204
205
Ошибка блока питания из-за перегрузки
Почтисть хеш платы, КПУ и адаптер плат от загрязнений и собрать все обратно.
Проверьте напряжение в сети.
206
Низкое напряжение в сети
Данная ошибка говорит о заниженном напряжение в сети, проверьте входящее напряжение.
Попробовать поменять розетку/фазу.
207
Защита блока питания из-за напряжения в сети
Проверить входное напряжение сети, для стабильной работы блока питания нужно 220~240 вольт.
Попробовать поменять розетку/фазу.
210
Ошибка блока питания
Смотреть статус ошибки блока питания.
213
Мощность потребления не соответствует входной мощности
Замените блок питания.
216
Входная мощность не изменялась длительное время
217
Ошибка включения блока питания
218
Напряжение в сети ниже 230 вольт
Для работы асика в режиме high нужно 230 вольт, а в сети меньше 230 вольт.
233
Защита блока питания от перегрева
Проверить температуру окружающей среды.
Выключить асик минут на 10, после попробовать еще раз.
Сделать оружающую среду более холодной.
234
235
236
Защита блока питания от перегрузки
Проверить затяжку винтов шины питания.
Проверить температуру окружающей среды.
Выключить асик минут на 10, после попробовать еще раз.
Сделать оружающую среду более холодной.
237
238
239
Защита блока питания от перенапряжения
Блок питания ушел в защиту из-за высокого напряжения.
Проверить напряжение в сети.
Выключить асик минут на 10, после попробовать еще раз.
Сделать оружающую среду более холодной.
240
Защита от низкого входящего напряжения
Блок питания ушел в защиту из-за слишком низкого напряжения в сети.
Проверить напряжение в сети.
Выключить асик минут на 10, после попробовать еще раз.
Попробовать поменять розетку/фазу.
Может происходить из-за:
1) Слишком большая нагрузка на сеть/фазу
2) Не справляется стабилизатор напряжения (если он есть)
3) Стоит релейный стабилизатор напряжения, из-за его конструкции у него кратковременно просаживается напряжение, для блока питания этого времени хватает, чтобы уйти в защиту.
241
Ошибка стабилизации напряжения
Замените блок питания.
243
Защита блока питания от перегрева
Проверить температуру окружающей среды.
Выключить асик минут на 10, после попробовать еще раз.
Сделать оружающую среду более холодной.
244
245
246
Защита блока питания от перегрузки из-за напряжения в сети
247
248
Защита блока питания от перенапряжения
Проверить напряжение в сети.
Для оптимальной работы блока питания ему нужно 220~230 Вольт стабильного напряжения.
Попробовать поменять розетку/фазу.
249
250
Защита блока питания от низкого напряжения в сети
251
253
Ошибка вентилятора блока питания
Проверить вентилятор блока питания.
Заменить вентилятор блока питания
Заменить блок питания.
254
255
Защита блока питания от перегрузки
Проверить температуру окружающей среды.
Выключить асик минут на 10, после попробовать еще раз.
Сделать оружающую среду более холодной.
256
257
Защита блока питания от перегрузки со стороны напряжения в сети
Отключить асик от сети минут на 5.
Заменить блок питания.
263
Ошибка связи с блоком питания
Проверьте затяжку винтов шины питания.
Проверьте шлейф подключения блока птания к КПУ.
Замените блок питания.
264
Ошибка связи с блоком питания
267
Критическая ошибка в работе блока питания
Свяжитесь с техническим специалистом или отправьте блок питания в ремонт.
268
Защита блока питания от перегрузки со стороны хеш-плат
Провеьте температуру окружающей среды.
Проверьте затяжку винтов шины питания.
Проверьте соединения на предмет короткого замыкания.
Сделать оружающую среду более холодной.
269
Защита блока питания от перегрузки из-за напряжения в сети
Проверить напряжение в сети. Для оптимальной работы блока питания ему нужно 220~230 вольт стабильного напряжения. Попробовать поменять розетку/фазу.
270
Защита блока питания от перенапряжения напряжением в сети
Блок питания ушел в защиту по напряжению.
Проверить напряжение в сети.
Выключить асик минут на 10, после попробовать еще раз.
Попробовать поменять розетку/фазу.
Заменить блок питания.
271
Защита от низкого напряжения в сети
Проверить напряжение в сети. Для оптимальной работы блока питания ему нужно 220~230 вольт стабильного напряжения. Попробовать поменять розетку/фазу.
272
Предупреждение о слишком большой выходной мощности блока питания
Провеьте температуру окружающей среды.
Проверьте затяжку винтов шины питания.
Сделать оружающую среду более холодной.
273
Слишком большая выходная мощность
274
Ошибка вентилятора блока питания
Проверить вентилятор блока питания (ничего ли ему не мешает вращаться).
Заменить вентилятор блока питания.
275
Высокая температура блока питания
Блок питания ушел в защиту по температуре.
Проверить температуру окружающей среды.
Выключить асик минут на 10, после попробовать еще раз.
Сделать оружающую среду более холодной.
300
Датчик температуры платы SM0 не обнаружен
Проверить шлейф от платы адаптера до контрольной платы.
Поменять две платы местами, если ошибка последует за платой, то плату в ремонт.
301
Датчик температуры платы SM1 не обнаружен
302
Датчик температуры платы SM2 не обнаружен
320
Ошибка считывания температуры с палты SM0
321
Ошибка считывания температуры с палты SM1
322
Ошибка считывания температуры с палты SM2
329
Ошибка связи с датчиком температуры контрольной платы
Проверьте шлейф и места подключения блока питания к контрольной платы.
Замените контрольную плату.
Замените блок питания.
350
Защита от перегрева платы SM0
Из-за высокой температуры платы ушли в защиту.
Проверить температуру окружающей среды.
Сделать оружающую среду более холодной.
Замените термоинтерфейс плат.
351
Защита от перегрева платы SM1
352
Защита от перегрева платы SM2
360
Перегрев хэш плат
410
Ошибка обнаружения файла конфигурации платы SM0
Перепрошить асик через sd-карту, потом через WhatsMinerTool.
Проверить адаптер плат и его шлейф.
Проверить затяжку винтов шины питания.
Попробовать заменить КПУ.
Попробовать заменить блок питания.
411
Ошибка обнаружения файла конфигурации платы SM1
412
Ошибка обнаружения файла конфигурации платы SM2
420
Ошибка анализа файла конфигурации платы SM0
Перепрошить асик через sd-карту, потом через WhatsMinerTool.
421
Ошибка анализа файла конфигурации платы SM1
422
Ошибка анализа файла конфигурации платы SM2
430
Ошибка данных чипов на плате SM0
431
Ошибка данных чипов на плате SM1
432
Ошибка данных чипов на плате SM2
440
Ошибка файла конфигурации чипа X на плате SM0
441
Ошибка файла конфигурации чипа X на плате SM1
442
Ошибка файла конфигурации чипа X на плате SM2
450
Ошибка верификации файла конфигурации платы SM0
Проверить шлейф адаптера плат к КПУ.
Перепрошить асик через sd-карту, потом через WhatsMinerTool.
451
Ошибка верификации файла конфигурации платы SM1
452
Ошибка верификации файла конфигурации платы SM2
510
Ошибка модели платы SM0
Модель хеш-платы не подходит к данному асику.
Замените хеш плату на подходящую.
511
Ошибка модели платы SM1
512
Ошибка модели платы SM2
520
Не подходящая модель платы SM0
521
Не подходящая модель платы SM1
522
Не подходящая модель платы SM2
530
Плата SM0 не найдена
Проверить затяжку болтов на шине питания.
Проверить подключение шлейфа адаптера плат к КПУ.
Попробовать поменять КПУ на новую, если ошибка пропала, то КПУ в ремонт.
Поменять две платы местами, если ошибка ушла за платой, то плату в ремонт.
531
Плата SM1 не найдена
532
Плата SM2 не найдена
540
Ошибка считывания id чипов на плате SM0
Проверить затяжку болтов на шине питания.
Проверить подключение шлейфа адаптера плат к КПУ.
Поменять две платы местами, если ошибка ушла за платой, то плату в ремонт.
541
Ошибка считывания id чипов на плате SM1
542
Ошибка считывания id чипов на плате SM2
550
На плате SM0 есть неисправные чипы
Поменять две платы местами, если ошибка пойдет за платой, то плату в ремонт.
551
На плате SM1 есть неисправные чипы
552
На плате SM2 есть неисправные чипы
560
Проблема в стабильности работы платы SM0
Проверить затяжку винтов на шине питания.
Проверить подключение шлейфа адаптера плат к КПУ.
Проверить параметры разгона.
Проверить напряжение в сети.
Поменять две платы местами, если ошибка ушла за платой, то плату в ремонт.
561
Проблема в стабильности работы платы SM1
562
Проблема в стабильности работы платы SM2
600
Высокая температура окружающей среды
При данной ошибке асик может продолжать работать, но во время тюна будет брать меньшие частоты, а во время работы может их занижать.
Данная ошибка может появляться при иммерсионном охлаждение из-за расположения датчика температуры.
Для иммерсионого охлаждения можно перевернуть асик, таким образом датчик температуры будет в более холодном месте.
Проверить температуру окружающей среды.
Сделать окружающую среду более холодной.
610
Слишком высокая температура окружающей среды для работы в режиме High
Ошибка возникает на профиле High при температуре окружающей среды выше 30 градусов. Асик автоматически вернется в профиль Normal.
Проверьте температуру окружающей среды.
Сделать окружающую среды более холодной.
701
Контрольная плата не поддерживает данную модель чипов
Перепрошить асик через sd-карту, потом через WhatsMinerTool.
Проверить затяжку винтов на шине питания.
Попробовать заменить КПУ.
710
Перезагрузка контрольной платы из-за ошибки в ее роботе
712
800
Ошибка сверки контрольной суммы cgminer
Перепрошить асик через сд карту, потом через WhatsMinerTool.
801
Ошибка сверки контрольной суммы системного монитора
802
Ошибка сверки контрольной суммы служебных задач
2000
Конфигурация пулов не найдена
Проверить настройки пулов.
2010
Все пулы выключены
При старте асика эта ошибка является нормой.
Проверить интернет.
Проверить настройки пулов.
Попробовать поменять пул.
Попробовать поменять провайдера (даже если другие устройства работают хорошо).
2020
Ошибка соединения с пулом №1
2021
Ошибка соединения с пулом №2
2022
Ошибка соединения с пулом №3
2030
Высокий процент реджектов
2040
Пул не поддерживает технологию ASICboost
Попробовать поменять пул, так как данный пул не поддерживает ASICboost.
2310
Слишком низкий хешрейт
Проверить напряжение в сети, оно должно быть стабильными и в районе 220~240 вольт.
Проверить интернет на предмет обрывов соединения.
Проверить температуру окружающей среды, плат и чипов.
2320
2340
Большой процент потерь хешрейта
2350
5110
Тайм-аут тюна на плате SM0
Перезагрузить майнер.
5111
Тайм-аут тюна на плате SM1
5112
Тайм-аут тюна на плате SM2
5070
Слишком быстрая скорость водного потока на плате SM0
Проверьте скорость потока воды.
5071
Слишком быстрая скорость водного потока на плате SM1
5072
Слишком быстрая скорость водного потока на плате SM2
8410
Ошибка версии прошивки (Пример: асик серии M2x с прошивкой от серии M3x)
Скачать верную версию прошивки.
Перепрошить асик через sd-карту, потом через WhatsMinerTool.
100001
Ошибка /antiv/signature
Перепрошить асик через sd-карту, потом через WhatsMinerTool.
100002
Ошибка /antiv/dig/initd.dig
100003
Ошибка /antiv/dig/pf_partial.dig
0x0001
Низкое напряжение в сети
Проверить входное напряжение сети, для стабильной работы блока питания нужно 220~240 вольт. Попробовать поменять розетку/фазу.
0x0002
Защита блока питания от перегрева силового радиатора
Отключить питание на 15 минут.
После включить обратно, если ошибка будет повторяться, то блок питания в ремонт.
0x0004
0x0008
Защита блока питания от перегрева
0x0010
Защита блока питания от перегрузки со стороны напряжения в сети
0x0020
Низкое напряжение на выходе с блока питания
Низкое выходное напряжение.
Проверьте напряжение в сети.
Замените блок питания.
0x0040
Перегрузка блока питания со стороны потребителя (непрерывная нагрузка в 320 ампер более 2 секунд)
Проверьте затяжку винтов шины питания.
0x0080
Перегрузка блока питания со стороны напряжения в сети
Отключить питание на 15 минут.
После включить обратно, если ошибка будет повторяться, то блок питания в ремонт.
0x0100
Перегрузка блока питания по одной цепи (нагрузка в 120 ампер)
Блок питания в ремонт.
0x0200
0x0400
0x0800
Неисправный вентилятор блока питания
Замените вентилятор блока питания.
0x1000
Перегрузка блока питания со стороны потребителя (непрерывная нагрузка в 310 ампер более 5 минут)
Проверьте блок питания на предмет короткого замыкания.
Ремонт блока питания.
0x2000
Перегрузка блока питания со стороны потребителя (непрерывная нагрузка в 295 ампер более 10 минут)
-
#1
Сорян, в теме не ту ошибку написал. В whatsminer tool выдаёт ошибку 100003. По кодам она описана так — 100003 /antiv/dig/pf_partial.dig Illegal. Но по вебморде ошибок нету. Гуглил — тишина. Может кто в курсе что это значит? Асик работает вполне себе исправно, единственно — задний вентилятор как-то странно короткими волнами меняет скорость. Вжжж-Вжжж-Вжжж.
-
#3
У меня была такая ошибка, при этом аппарат перестал майнить, удаленная перезагрузка не помогала. Пришлось обесточить. После не появлялась
-
#4
У меня была такая ошибка, при этом аппарат перестал майнить, удаленная перезагрузка не помогала. Пришлось обесточить. После не появлялась
Помогла перепрошивка.
300
Ошибка обнаружения датчика температуры SM0
Проверьте подключение хэш-платы
301
Ошибка обнаружения датчика температуры SM1
302
Ошибка обнаружения датчика температуры SM2
320
Ошибка связи с датчиком температуры платы SM0
Проверьте, заблокированы ли винты панели управления, проверьте переходную пластину и контакты кабеля
321
Ошибка связи с датчиком температуры платы SM1
322
Ошибка связи с датчиком температуры платы SM2
329
Температура платы управления ошибка связи с датчиком
Замените источник питания
350
Защита от перегрева SM0
Проверьте температуру окружающей среды (рекомендуется использовать инфракрасный термометр GS320).
351
SM1 защита от перегрева
352
SM2 защита от перегрева
360
Температура хэш-платы перегревается
410
SMO обнаружило ошибку eeprom
Проверьте переходную пластину и контакт кабеля
411
SM1 обнаружило ошибку eeprom
412
SM2 обнаружило ошибку eeprom
420
SM0 ошибка синтаксического анализатора eeprom
Обновить прошивку
421
SM1 ошибка синтаксического анализатора eeprom
422
M2 ошибка eeprom синтаксического анализатора
430
Ошибка типа бина микросхемы SM0
431
Ошибка типа бина микросхемы SM1
432
Ошибка типа буфера микросхемы SM2
440
Ошибка SM0 eeprom chip num X
441
Ошибка SM1 eeprom chip num X
442
SM2 номер микросхемы eeprom X ошибка
450
SM0 eeprom xfer error
Проверьте плату адаптера и контакты проводки.Обновите прошивку
451
SM1 eeprom xfer error
452
SM2 eeprom xfer error
510
SM0 ошибка типа майнера
Версия и тип хэшборда несовместимы, замените правильный хэшборд
511
SM1 ошибка типа майнера
512
Ошибка типа майнера SM2
520
Ошибка типа бина SM0
Если тип чипа хэш-платы несовместим, замените правильную хэш-плату
521
Ошибка типа бина SM1
522
Ошибка типа бина SM2
530
Плата SM0 не обнаружена
Проверьте проводку платы адаптера и кабель, или замените плату управления, чтобы проверить, припаян
ли
разъем хэш-платы.
531
Плата SM1 не обнаружена
532
Плата SM2 не обнаружена
540
Количество микросхем SM0 неполное
Проверьте переходную пластину и контакт кабеля
541
Количество микросхем SM1 неполное
542
Количество микросхем SM2 неполное
550
SM0 имеет плохие чипы
Замените плохую микросхему в позиции печати
551
SM1 имеет плохие чипы
552
SM2 имеет плохие чипы
560
SM0 потеря баланса
Подключите переходную пластину, а затем снова прикрутите хэш-плату для подключения питания
561
SM1 потеря баланса
562
SM2 потеря баланса
590
Частота SM0 слишком низкая
Замените хэш-плату и поместите вместе хэш-платы, которые сообщили об одной и той же ошибке
591
Частота SM1 слишком низкая
592
Частота SM2 слишком низкая
600
Слишком высокая температура окружающей среды
Проверьте температуру окружающей среды
610
Если температура окружающей среды слишком высока в режиме высокой производительности, вернитесь в
нормальный
режим
Проверьте температуру окружающей среды, в режиме высокой производительности должна быть ниже 30 ℃.
701
На плате управления отсутствует микросхема поддержки
Обновление соответствующего типа микропрограммы
710
Ошибка платы управления
Обновите до последней версии прошивки
712
Плата управления перезагрузилась как исключение
Обновление последней версии прошивки. Проверьте, правильно ли зафиксирован винт платы управления
800
Ошибка контрольной суммы cgminer
Обновление микропрограммы
801
Ошибка контрольной суммы системного монитора
802
Ошибка контрольной суммы системного монитора
2000
Не настроена информация о пуле
Проверьте конфигурацию пула
2010
Все подключения к пулам майнинга не удались
Проверьте настройки сети или пулов майнинга
2020
Не удалось установить соединение с пулом майнинга
2021
Не удалось установить соединение с пулом майнинга
2022
Не удалось установить соединение с пулом майнинга
2030
Скорость повторного срабатывания пула майнинга слишком высока
Проверьте настройки сети или пула майнинга, а также настройки майнинга криптовалюты
2040
Пул не поддерживает режим asicboost
Проверьте конфигурацию пула
2310
Хэшрейт слишком низкий
Проверьте входное напряжение, сетевое окружение и температуру окружающей среды.
2320
Скорость хэширования слишком низкая
2340
Потеря хэшрейта слишком высока
2350
Потеря скорости хэширования слишком высока
5070
Скорость потока воды SM0 ненормальная
Проверьте, нормальный ли поток воды
5071
SM1 Скорость течения воды ненормальная
5072
SM2 Скорость потока воды ненормальная
5110
SM0 Таймаут повышения частоты
Перезагрузите
5111
SM1 Таймаут повышения частоты
5112
SM2 Таймаут повышения частоты
8410
Ошибка версии программного обеспечения (miner M2x с прошивкой M3x или M3x с прошивкой M2x)
Обновление до правильной версии прошивки
100001
/antiv/signature illegal
Обновление до последней версии микропрограммы или запись карты
100002
/antiv/dig/initd.dig illegal
Обновление до последней версии микропрограммы или запись карты
100003
/antiv/dig/pf_partial.dig illegal
Обновление до последней версии микропрограммы или запись карты
Error code:110
Meaning:Inlet fan detcction speed error
Corresponding solutions: Check whether the fan connction is normal, or replace the power supply, or replace the fan
Error code:111
Meaning:Outlet fan detection speed error
Corresponding solutions:
Error code:120
Meaning:Inlet fan speed error(Deviation 2000+)
Corresponding solutions:
Error code:121
Meaning:Outlet fan speed error(Deviation 2000+)
Corresponding solutions:
Error code:130
Meaning:Inlet fan speed error
Corresponding solutions:
Error code:131
Meaning:Outlet fan spced error
Corresponding solutions:
Error code:140
Meaning:Fan speed is too high
Corresponding solutions: Please check the environment temperature
Error code:200
Meaning:Power detection error
Corresponding solutions: Detecting the power output cable, or updating the latest firmware, or replacing the power supply
Error code:201
Meaning:Power does not match the configuration file
Corresponding solutions: Updating to the latest software
Error code:202
Meaning:Power output voltage error
Corresponding solutions: Updating to the latest software or check the power supply
Error code:203
Meaning:Power supply protection
Corresponding solutions: Please check the environment temperature
Error code:204
Meaning:Power supply current protection
Corresponding solutions:
Error code:205
Meaning:Power current error
Corresponding solutions: Inspection of power supply in power grid
Error code:206
Meaning:Power input voltage is low
Corresponding solutions: Improve power supply conditions and input voltage
Error code:207
Meaning:Power input current protecting
Corresponding solutions:
Error code:210
Meaning:Power status error
Corresponding solutions: Check the power failure code
Error code:213
Meaning:Power input voltage and current do not match the power
Corresponding solutions: Replace the PSU
Error code:216
Meaning:Power remained unchanged for a long time
Corresponding solutions:
Error code:217
Meaning:Power set enable error
Corresponding solutions:
Error code:218
Meaning:Power input voltage is lower than 230V for high power mode
Corresponding solutions: Increase input voltage,replace power supply
Error code:233
Meaning:Overtemperature Protection of Power Output
Corresponding solutions: Plcase check the environment temperature
Error code:234
Meaning:Overtemperature Protection of Power Output
Corresponding solutions:
Error code:235
Meaning:Overtemperature Protection of Power Output
Corresponding solutions:
Error code:236
Meaning:Overcurrent Protection of Power Output
Corresponding solutions: Please check the environment temperature and the copper wire screw(Recommend to use the protable electric screwdriver)
Error code:237
Meaning:Overcurrent Protection of Power Output
Corresponding solutions:
Error code:238
Meaning:Overcurrent Protection of Power Output
Corresponding solutions:
Error code:239
Meaning:Overvoltage Protection of Power Output
Corresponding solutions: Check grid power
Error code:240
Meaning:Low Voltage Protection for Power Output
Corresponding solutions:
Error code:241
Meaning:Power output current imbalance
Corresponding solutions: Replace the power
Error code:243
Meaning:Over-tempcrature Protection for Power Input
Corresponding solutions: Please check the environment temperature
Error code:244
Meaning:Over-temperature Protection for Power Input
Corresponding solutions:
Error code:245
Meaning:Over-tempcrature Protection for Power Input
Corresponding solutions:
Error code:246
Meaning:Overcurrent Protection for Power Input
Corresponding solutions:
Error code:247
Meaning:Overcurrent Protection for Power Input
Corresponding solutions:
Error code:248
Meaning:Overvoltage Protection for Power Input
Corresponding solutions: Check grid power
Error code:249
Meaning:Overvoltage Protection for Power Input
Corresponding solutions:
Error code:250
Meaning:Undervoltage Protection for Power Input
Corresponding solutions:
Error code:251
Meaning:Undervoltage Protection for Power Input
Corresponding solutions:
Error code:253
Meaning:Power Fan Error
Corresponding solutions: Replace the power supply
Error code:254
Meaning:Power Fan Error
Corresponding solutions:
Error code:255
Meaning:Protection of over power output
Corresponding solutions: Please check the environment temperature
Error code:256
Meaning:Protection of over power output
Corresponding solutions:
Error code:257
Meaning:Input over current protection of power supply primary side
Corresponding solutions: Try to power off and restart, no effect to replace the power supply
Error code:263
Meaning:Power communication warning
Corresponding solutions: Check whether the screws of the control board are locked
Error code:264
Meaning:Power communication error
Corresponding solutions:
Error code:267
Meaning:Power watchdog protection
Corresponding solutions: Contact the technician in time
Error code:268
Meaning:Power output over-current protection
Corresponding solutions: Check the ambient temperature, check the copper bar screw
Error code:269
Meaning:Power input over-current protection
Corresponding solutions: Improve power supply conditions and input voltage
Error code:270
Meaning:Power input over-voltage protection
Corresponding solutions: Inspection of input voltage in power grid
Error code:271
Meaning:Power input under-voltage protection
Corresponding solutions:
Error code:272
Meaning:Warning of excessive power
output of power supply
Corresponding solutions: Please check the environment temperature
Error code:273
Meaning:Power input power too high warning
Corresponding solutions:
Error code:274
Meaning:Power fan warning
Corresponding solutions: Check if the power fan is blocked and may need to be replaced
Error code:275
Meaning:Power over temperature warning
Corresponding solutions: Please check the environment temperature
Error code:300
Meaning:SM0 temperature sensor detection error
Corresponding solutions: Check the connection of the hash board
Error code:301
Meaning:SM1 temperature sensor detection error
Corresponding solutions:
Error code:302
Meaning:SM2 temperature sensor detection error
Corresponding solutions:
Error code:320
Meaning:SM0 board temperature sensor communication error
Corresponding solutions: Check if the control panel screws are locked, check the adapter plate and the cable contacts
Error code:321
Meaning:SM1 board temperature sensor communication error
Corresponding solutions:
Error code:322
Meaning:SM2 board temperature sensor communication error
Corresponding solutions:
Error code:329
Meaning:Control board temperature
sensor communication error
Corresponding solutions: Replace the power supply
Error code:350
Meaning:SM0 tempcrature protection
Corresponding solutions: Check the environment temperature (Recommend to use the GS320 infrared thermometer)
Error code:351
Meaning:M1 tempcrature protection
Corresponding solutions:
Error code:352
Meaning:SM2 tempcrature protection
Corresponding solutions:
Error code:360
Meaning:The temperature of the hash board is overheating
Corresponding solutions:
Error code:410
Meaning:SMO detect eeprom error
Corresponding solutions: Check adapter plate and cable contact
Error code:411
Meaning:SM1 detect eeprom error
Corresponding solutions:
Error code:412
Meaning:SM2 detect eeprom error
Corresponding solutions:
Error code:420
Meaning:SM0 parser eeprom error
Corresponding solutions: Upgrade firmware
Error code:421
Meaning:SM1 parser eeprom error
Corresponding solutions:
Error code:422
Meaning:SM2 parser eeprom error
Corresponding solutions:
Error code:430
Meaning:SM0 chip bin type error
Corresponding solutions:
Error code:431
Meaning:SM1 chip bin type error
Corresponding solutions:
Error code:432
Meaning:SM2 chip bin type error
Corresponding solutions:
Error code:440
Meaning:SM0 eeprom chip num X error
Corresponding solutions:
Error code:441
Meaning:SM1 eeprom chip num X error
Corresponding solutions:
Error code:442
Meaning:SM2 eeprom chip num X error
Corresponding solutions:
Error code:450
Meaning:SM0 eeprom xfer error
Corresponding solutions: Check adapter board and wiring contacts.Upgrade firmware
Error code:451
Meaning:SM1 eeprom xfer error
Corresponding solutions:
Error code:452
Meaning:SM2 eeprom xfer error
Corresponding solutions:
Error code:510
Meaning:SM0 miner type error
Corresponding solutions: The version and type of hashboard are
inconsistent, replace the correct hashboard
Error code:511
Meaning:SM1 miner type error
Corresponding solutions:
Error code:512
Meaning:SM2 miner type error
Corresponding solutions:
Error code:520
Meaning:SM0 bin type error
Corresponding solutions: If the chip type of the hash board is inconsistent, replace the correct hash board.
Error code:521
Meaning:SM1 bin type error
Corresponding solutions:
Error code:522
Meaning:SM2 bin type error
Corresponding solutions:
Error code:530
Meaning:SM0 board is not detected
Corresponding solutions: Check the adapter board wiring and cablc, or replace the control board to check whether the hash board connector is soldered
Error code:531
Meaning:SM1 board is not detected
Corresponding solutions:
Error code:532
Meaning:SM2 board is not detected
Corresponding solutions:
Error code:540
Meaning:The number of SM0 chips is incomplete
Corresponding solutions: Check adapter plate and cable contact
Error code:541
Meaning:The number of SM1 chips is incomplete
Corresponding solutions:
Error code:542
Meaning:The number of SM2 chips is incomplete
Corresponding solutions:
Error code:550
Meaning:SM0 has bad chips
Corresponding solutions: Replace the bad chip in the print position
Error code:551
Meaning:SM1 has bad chips
Corresponding solutions:
Error code:552
Meaning:SM2 has bad chips
Corresponding solutions:
Error code:560
Meaning:SM0 loss balance
Corresponding solutions: Plug in the adapter plate, and then screw in the power connection hash board again
Error code:561
Meaning:SM1 loss balance
Corresponding solutions:
Error code:562
Meaning:SM2 loss balance
Corresponding solutions:
Error code:590
Meaning:SM0 frequency is too low
Corresponding solutions: Replace the hash board and place the hash boards which reported the same error together
Error code:591
Meaning:SM1 frequency is too low
Corresponding solutions:
Error code:592
Meaning:SM2 frequency is too low
Corresponding solutions:
Error code:
Meaning:
Corresponding solutions:
Error code:600
Meaning:Environment temperature is too high
Corresponding solutions: Check the environment temperature
Error code:610
Meaning:If the ambient temperature is too high in high performance mode, return to normal mode
Corresponding solutions: Check the ambient temperature, high
performance mode needs to be ontrolled below 30 ℃
Error code:701
Meaning:Control board no support chip
Corresponding solutions: Upgrade the corresponding type of firmware
Error code:710
Meaning:Control board error
Corresponding solutions: Update to the latest firmware
Error code:712
Meaning:Control board rebooted as exception
Corresponding solutions: Updating the latest firmware.Check whether the control board screw is locked properly
Error code:800
Meaning:cgminer checksum error
Corresponding solutions: Re-upgrade firmware
Error code:801
Meaning:system-monitor checksum error
Corresponding solutions:
Error code:802
Meaning:system-monitor checksum error
Corresponding solutions:
Error code:2000
Meaning:No pool information configured
Corresponding solutions: Check pool configuration
Error code:2010
Meaning:All mining pool connections failed
Corresponding solutions: Check the network or mining pools setting
Error code:2020
Meaning:Mining pool0 connection failed
Corresponding solutions:
Error code:2021
Meaning:Mining pool1 connection failed
Corresponding solutions:
Error code:2022
Meaning:Mining pool2 connection failed
Corresponding solutions:
Error code:2030
Meaning:Mining pool rejcction rate is too high
Corresponding solutions: Check the network or mining pool setting, and the mining setting of the cryptocurrency
Error code:2040
Meaning:The pool does not support
the asicboost mode
Corresponding solutions: Check pool configuration
Error code:2310
Meaning:Hash rate is too low
Corresponding solutions: Check input voltage, network environment, and ambient temperature
Error code:2320
Meaning:Hash rate is too low
Corresponding solutions:
Error code:2340
Meaning:The loss of hash rate is too high
Corresponding solutions:
Error code:2350
Meaning:The loss of hash rate is too high
Corresponding solutions:
Error code:5070
Meaning:SM0 water velocity is abnormal
Corresponding solutions: Check if the water flow is normal
Error code:5071
Meaning:SM1 water velocity is abnormal
Corresponding solutions:
Error code:5072
Meaning:SM2 water velocity is abnormal
Corresponding solutions:
Error code:5110
Meaning:SM0 Frequency Up Timeout
Corresponding solutions: reboot
Error code:5111
Meaning:SM1 Frequency Up Timeout
Corresponding solutions:
Error code:5112
Meaning:SM2 Frequency Up Timeout
Corresponding solutions:
Error code:8410
Meaning:Software version error (M2x miner with M3x firmware, or M3x with M2x firmware)
Corresponding solutions: Upgrade to the correct firmware version
Error code:100001
Meaning:/antiv/signature Illegal
Corresponding solutions: Upgrade the latest firmware or burn the card
Error code:100002
Meaning:/antiv/dig/initd.dig Illegal
Corresponding solutions:
Error code:100003
Meaning:/antiv/dig/pf_partial.dig Illegal
Corresponding solutions:
Error code:PSU Error code
Meaning:Reason
Corresponding solutions: processing method
Error code:0x0001
Meaning:Input undervoltage
Corresponding solutions: Check the power supply
Error code:0x0002
Meaning:Temperature sampling over temperature protection of power radiator
Corresponding solutions: Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Error code:0x0004
Meaning:Temperature sampling over
temperature protection of power radiator
Corresponding solutions:
Error code:0x0008
Meaning:Over temperature protection of environmental emperature sampling in power supply
Corresponding solutions:
Error code:0x0010
Meaning:Primary side over current
Corresponding solutions: Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Error code:0x0020
Meaning:Output undervoltage
Corresponding solutions: Check the power supply
Error code:0x0040
Meaning:Output over current (continuous load 320A for more than 2S)
Corresponding solutions: Tighten the copper bar screw again
Error code:0x0080
Meaning:Primary side over current
Corresponding solutions: Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Error code:0x0100
Meaning:Single circuit overcurrent (protection point 120a)
Corresponding solutions: Check the PSU
Error code:0x0200
Meaning:Single circuit overcurrent (protection point 120a)
Corresponding solutions:
Error code:0x0400
Meaning:Single circuit overcurrent
(protection point 120a)
Corresponding solutions:
Error code:0x0800
Meaning:Fan failure
Corresponding solutions: Replace the PSU
Error code:0x1000
Meaning:Output over current (continuous load of 310A
for more than 5min)
Corresponding solutions: Check the PSU
Error code:0x2000
Meaning:Output over current
(continuous load 295A for
more than 10min)
Corresponding solutions:
Meaning:
Corresponding solutions:
Here is the WhatsMiner checklist of error code and we strongly recommend every WhatsMiner user to keep it because almost 80% of the problems can be solved by corresponding solutions.
We hope it is helpful for all WhatsMiner users. For rest of the problems, Kindly reach us and we’re willing to help.
Meaning of Error Code and Corresponding Solutions on WhatsM liner Tool 1 |
||
Error Code |
Meaning |
Corresponding Solutions |
110 |
Inlet fan detcction speed error |
Check whether the fan connction is normal, or replace the power supply, or replace the fan |
111 |
Outlet fan detection speed error |
|
120 | Inlet fan speed error(Deviation 2000+) | |
121 | Outlet fan speed error(Deviation 2000+) | |
130 |
Inlet fan speed error |
|
131 |
Outlet fan spced error |
|
140 |
Fan speed is too high |
Please check the environment temperature |
200 |
Power detection error |
Detecting the power output cable, or updating the latest firmware, or replacing the power supply |
201 |
Power does not match the configuration file |
Updating to the latest software |
202 |
Power output voltage error |
Updating to the latest software or check the power supply |
203 |
Power supply protection |
Please check the environment temperature |
204 |
Power supply current protection |
|
205 |
Power current error |
Inspection of power supply in power grid |
206 |
Power input voltage is low |
Improve power supply conditions and input voltage |
207 |
Power input current protecting |
|
210 |
Power status error |
Check the power failure code |
213 |
Power input voltage and current do not match the power |
Replace the PSU |
216 | Power remained unchanged for a long time | |
217 | Power set enable error | |
218 | Power input voltage is lower than 230V for high power mode | Increase input voltage,replace power supply |
233 |
Overtemperature Protection of Power Output |
Plcase check the environment temperature |
234 |
Overtemperature Protection of Power Output |
|
235 |
Overtemperature Protection of Power Output |
|
236 |
Overcurrent Protection of Power Output |
Please check the environment temperature and the copper wire screw(Recommend to use the protable electric screwdriver) |
237 |
Overcurrent Protection of Power Output |
|
238 |
Overcurrent Protection of Power Output |
|
239 |
Overvoltage Protection of Power Output |
Check grid power |
240 |
Low Voltage Protection for Power Output |
|
241 |
Power output current imbalance |
Replace the power |
243 |
Over-tempcrature Protection for Power Input |
Please check the environment temperature |
244 |
Over-temperature Protection for Power Input |
|
245 |
Over-tempcrature Protection for Power Input |
|
246 |
Overcurrent Protection for Power Input |
|
247 |
Overcurrent Protection for Power Input |
|
248 |
Overvoltage Protection for Power Input |
Check grid power |
249 |
Overvoltage Protection for Power Input |
|
250 |
Undervoltage Protection for Power Input |
|
251 |
Undervoltage Protection for Power Input |
|
253 |
Power Fan Error |
Replace the power supply |
254 |
Power Fan Error |
|
255 |
Protection of over power output |
Please check the environment temperature |
256 |
Protection of over power output |
|
257 |
Input over current protection of power supply primary side |
Try to power off and restart, no effect to replace the power supply |
263 |
Power communication warning |
Check whether the screws of the control board are locked |
264 |
Power communication error |
|
267 |
Power watchdog protection |
Contact the technician in time |
268 |
Power output over-current protection |
Check the ambient temperature, check the copper bar screw |
269 |
Power input over-current protection |
Improve power supply conditions and input voltage |
270 |
Power input over-voltage protection |
Inspection of input voltage in power grid |
271 |
Power input under-voltage protection |
|
272 |
Warning of excessive power output of power supply |
Please check the environment temperature |
273 |
Power input power too high warning |
|
274 |
Power fan warning |
Check if the power fan is blocked and may need to be replaced |
275 |
Power over temperature warning |
Please check the environment temperature |
Meaning of Error Code and Corresponding Solutions on WhatsMiner Tool 2 |
||
Error Code |
Meaning |
Corresponding Solutions |
300 |
SM0 temperature sensor detection error |
Check the connection of the hash board |
301 |
SM1 temperature sensor detection error |
|
302 |
SM2 temperature sensor detection error |
|
320 |
SM0 board temperature sensor communication error |
Check if the control panel screws are locked, check the adapter plate and the cable contacts |
321 |
SM1 board temperature sensor communication error |
|
322 |
SM2 board temperature sensor communication error |
|
329 |
Control board temperature sensor communication error |
Replace the power supply |
350 |
SM0 tempcrature protection |
Check the environment temperature (Recommend to use the GS320 infrared thermometer) |
351 |
M1 tempcrature protection |
|
352 |
SM2 tempcrature protection |
|
360 | The temperature of the hash board is overheating | |
410 |
SMO detect eeprom error |
Check adapter plate and cable contact |
411 |
SM1 detect eeprom error |
|
412 |
SM2 detect eeprom error |
|
420 |
SM0 parser eeprom error |
Upgrade firmware |
421 |
SM1 parser eeprom error |
|
422 |
SM2 parser eeprom error |
|
430 |
SM0 chip bin type error |
|
431 |
SM1 chip bin type error |
|
432 |
SM2 chip bin type error |
|
440 |
SM0 eeprom chip num X error |
|
441 |
SM1 eeprom chip num X error |
|
442 |
SM2 eeprom chip num X error |
|
450 | SM0 eeprom xfer error | Check adapter board and wiring contacts.Upgrade firmware |
451 | SM1 eeprom xfer error | |
452 | SM2 eeprom xfer error | |
510 |
SM0 miner type error |
The version and type of hashboard are inconsistent, replace the correct hashboard |
511 |
SM1 miner type error |
|
512 |
SM2 miner type error |
|
520 | SM0 bin type error | If the chip type of the hash board is inconsistent, replace the correct hash board. |
521 | SM1 bin type error | |
522 | SM2 bin type error | |
530 |
SM0 board is not detected |
Check the adapter board wiring and cablc, or replace the control board to check whether the hash board connector is soldered |
531 |
SM1 board is not detected |
|
532 |
SM2 board is not detected |
|
540 |
The number of SM0 chips is incomplete |
Check adapter plate and cable contact |
541 |
The number of SM1 chips is incomplete |
|
542 |
The number of SM2 chips is incomplete |
|
550 |
SM0 has bad chips |
Replace the bad chip in the print position |
551 |
SM1 has bad chips |
|
552 |
SM2 has bad chips |
|
560 |
SM0 loss balance |
Plug in the adapter plate, and then screw in the power connection hash board again |
561 |
SM1 loss balance |
|
562 |
SM2 loss balance |
|
590 |
SM0 frequency is too low |
Replace the hash board and place the hash boards which reported the same error together |
591 |
SM1 frequency is too low |
|
592 |
SM2 frequency is too low |
|
600 |
Environment temperature is too high |
Check the environment temperature |
610 |
If the ambient temperature is too high in high performance mode, return to normal mode |
Check the ambient temperature, high performance mode needs to be ontrolled below 30 ℃ |
701 | Control board no support chip | Upgrade the corresponding type of firmware |
710 |
Control board error |
Update to the latest firmware |
712 | Control board rebooted as exception | Updating the latest firmware.Check whether the control board screw is locked properly |
800 |
cgminer checksum error |
Re-upgrade firmware |
801 |
system-monitor checksum error |
|
802 |
system-monitor checksum error |
|
2000 | No pool information configured | Check pool configuration |
2010 |
All mining pool connections failed |
Check the network or mining pools setting |
2020 |
Mining pool0 connection failed |
|
2021 |
Mining pool1 connection failed |
|
2022 |
Mining pool2 connection failed |
|
2030 |
Mining pool rejcction rate is too high |
Check the network or mining pool setting, and the mining setting of the cryptocurrency |
2040 |
The pool does not support the asicboost mode |
Check pool configuration |
2310 | Hash rate is too low | Check input voltage, network environment, and ambient temperature |
2320 | Hash rate is too low | |
2340 | The loss of hash rate is too high | |
2350 | The loss of hash rate is too high | |
5070 | SM0 water velocity is abnormal | Check if the water flow is normal |
5071 | SM1 water velocity is abnormal | |
5072 | SM2 water velocity is abnormal | |
5110 |
SM0 Frequency Up Timeout |
reboot |
5111 |
SM1 Frequency Up Timeout |
|
5112 |
SM2 Frequency Up Timeout |
|
8410 | Software version error (M2x miner with M3x firmware, or M3x with M2x firmware) | Upgrade to the correct firmware version |
100001 | /antiv/signature Illegal | Upgrade the latest firmware or burn the card |
100002 | /antiv/dig/initd.dig Illegal | |
100003 |
/antiv/dig/pf_partial.dig Illegal |
PSU Error code |
Reason |
processing method |
0x0001 |
Input undervoltage |
Check the power supply |
0x0002 |
Temperature sampling over temperature protection of power radiator |
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply |
0x0004 |
Temperature sampling over temperature protection of power radiator |
|
0x0008 |
Over temperature protection of environmental emperature sampling in power supply |
|
0x0010 |
Primary side over current |
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply |
0x0020 |
Output undervoltage |
Check the power supply |
0x0040 |
Output over current (continuous load 320A for more than 2S) |
Tighten the copper bar screw again |
0x0080 |
Primary side over current |
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply |
0x0100 |
Single circuit overcurrent (protection point 120a) |
Check the PSU |
0x0200 |
Single circuit overcurrent (protection point 120a) |
|
0x0400 |
Single circuit overcurrent (protection point 120a) |
|
0x0800 |
Fan failure |
Replace the PSU |
0x1000 |
Output over current (continuous load of 310A for more than 5min) |
Check the PSU |
0x2000 |
Output over current (continuous load 295A for more than 10min) |
We hope it is helpful for all WhatsMiner users. For rest of the problems, Kindly reach us and we’re willing to help.
Рекомендуемые сообщения
-
- Поделиться
День, добрый — подскажите стабильную надежную прошивку для whatsminer m21s ? С условием разгона или видео как разогнать на стандартной если это возможно?
Без вирусного вмешательства.
Ссылка на комментарий
Поделиться на другие сайты
-
- Поделиться
02.09.2021 в 09:17, sergeomsk сказал:
День, добрый — подскажите стабильную надежную прошивку для whatsminer m21s ? С условием разгона или видео как разогнать на стандартной если это возможно?
Без вирусного вмешательства.
Здравствуйте, нашли что-нибудь?
Есть ли смысл, меняется ли потребление или мощность?
Ссылка на комментарий
Поделиться на другие сайты
- Автор
-
- Поделиться
06.09.2021 в 22:48, AndreyWey сказал:
Здравствуйте, нашли что-нибудь?
Есть ли смысл, меняется ли потребление или мощность?
Добрый день, как видите еще ни кто не отписал -а ставить левак с простор инета я бы не стал)
Ссылка на комментарий
Поделиться на другие сайты
- 1 месяц спустя…
-
- Поделиться
Неужели никто не может отписать ? никто не ставил прошивки ? поделись результатами
Ссылка на комментарий
Поделиться на другие сайты
-
- Поделиться
прошивка есть насколько я знаю..
Ссылка на комментарий
Поделиться на другие сайты
- 1 месяц спустя…
-
- Поделиться
02.09.2021 в 11:17, sergeomsk сказал:
День, добрый — подскажите стабильную надежную прошивку для whatsminer m21s ? С условием разгона или видео как разогнать на стандартной если это возможно?
Без вирусного вмешательства.
10.10.2021 в 21:25, Владимир Салихин сказал:
прошивка есть насколько я знаю..
Добрый день! У меня тоже есть вопрос по прошивке.
Прошивка есть на офф сайте, как обновится есть видео в интернете, но смущает фраза на офф сайте «Онлайн-обновление до версии, более ранней, чем 20210602, запрещено, необходимо сопоставить с инструментом whatsminertool новая версия» , что это значит не могу понять. Инструмент WhatsMinerTool-8.1.17-EN.zip тоже есть на офф сайте.
Или текущие прошивки не подходят к старым версиям tool ?
Ссылка на комментарий
Поделиться на другие сайты
- 1 месяц спустя…
-
- Поделиться
День добрый. Кто в итоге шился ранее упомянутом способом. Все ли нормально и стабильно.
У меня вот такая версия прошивки 20191105.22.1 и там походу вирусня вчера на нем поменялись пулы и логин проль.
Изменено 9 Jan 2022, 13:56 пользователем maks85
Ссылка на комментарий
Поделиться на другие сайты
-
- Поделиться
Доброго времени. Я шился, только что таким способом. Хотел побороть пару ошибок на двух машинках.
Итог: шьется нормально, но как я заметил только на платах H3, на H6 зашилось, но после ребута выдал новую ошибку 100003 Illegal access to the system.
Выясняю, как теперь залить другую прошивку, но скорей всего уже придется через sd карту. Может еще кто что подскажет…
Ссылка на комментарий
Поделиться на другие сайты
-
- Поделиться
шей
17 часов назад, bsdnick сказал:
Доброго времени. Я шился, только что таким способом. Хотел побороть пару ошибок на двух машинках.
Итог: шьется нормально, но как я заметил только на платах H3, на H6 зашилось, но после ребута выдал новую ошибку 100003 Illegal access to the system.
Выясняю, как теперь залить другую прошивку, но скорей всего уже придется через sd карту. Может еще кто что подскажет…
шей с карты сразу ! а потом через програмулину апгрейд делай все отлично станет ! если убьешь контрольку у меня не дорого есть стучи.. каноль )))
Ссылка на комментарий
Поделиться на другие сайты
-
- Поделиться
Такс.. с флэшки прошился и накатил апгрейд через фирменную прогу. Все заработало.
Вот может вопрос не по теме этой ветки, но все же, кто-нибудь шил блок питания на этих асиках? Есть информация?
Изменено 16 Jan 2022, 18:19 пользователем bsdnick
Ссылка на комментарий
Поделиться на другие сайты
-
- Поделиться
Всем доброго дня. Проши в итоге на удачу все встало нормально через прогу так что можно смело шить, ну во всяком случае у меня все стабильно.
Ссылка на комментарий
Поделиться на другие сайты
- 6 месяцев спустя…
-
- Поделиться
В 02.09.2021 в 08:17, sergeomsk сказал:
День, добрый — подскажите стабильную надежную прошивку для whatsminer m21s ? С условием разгона или видео как разогнать на стандартной если это возможно?
Без вирусного вмешательства.
Здравствуйте
предлагаем протестировать прошивку whatsminer от компании BiXBiT Dev.
Первые в мире!
Анонс прошивки для Whatsminer
Разгон для x2, x3, x5 серий и многое другое!
https://youtu.be/1vLTx5-jBMI
Друзья, подписывайтесь на новостной канал в телеграмм: ?
@BiXBiT_Dev_News_ru
Изменено 17 Aug 2022, 21:53 пользователем BiXBiT_Dev
Картинка плохого качества.
Ссылка на комментарий
Поделиться на другие сайты
-
- Поделиться
В 18.08.2022 в 05:51, BiXBiT_Dev сказал:
Здравствуйте, после отката с вашей прошивки на оригинальную, полезли ошибки по перегреву БП, выяснилось что кулер БП работает некорректно, как теперь откатить прошивку БП ? (P21D )
Здравствуйте
предлагаем протестировать прошивку whatsminer от компании BiXBiT Dev.
Первые в мире!
Анонс прошивки для Whatsminer
Разгон для x2, x3, x5 серий и многое другое!
https://youtu.be/1vLTx5-jBMI
Друзья, подписывайтесь на новостной канал в телеграмм: ?
@BiXBiT_Dev_News_ru
Ссылка на комментарий
Поделиться на другие сайты
-
- Поделиться
@Vadike84
1 час назад, Vadike84 сказал:
полезли ошибки по перегреву БП, выяснилось что кулер БП работает некорректно,
Это в какой прошивке можно увидеть такие ошибки?
Ссылка на комментарий
Поделиться на другие сайты
-
- Поделиться
всем привет! Кто нибуть уже установил Фирменная прошивка для ASIC устройств от BiXBiT ?
как она в работе
Ссылка на комментарий
Поделиться на другие сайты
-
- Поделиться
13 часов назад, BERCUD75 сказал:
@Vadike84
Это в какой прошивке можно увидеть такие ошибки?
В любой, перегрейте БП и увидите ошибку
12 часов назад, Aim1000kg сказал:
всем привет! Кто нибуть уже установил Фирменная прошивка для ASIC устройств от BiXBiT ?
как она в работе
На воздухе от этой прошивки мало толку, так, разве что, подтянуть хэш до номинала на уставших асиках перед продажей. Установил на м21с 56, который выдавал 54. Подтянул показатели до 57. Потребление выросло на 200вт до 3570вт. Хотел поиграться с прошивкой на м31с 74, но в вебморде нажал «обновить прошивку БП» — думал что это для оверклока!!! теперь сижу с отключенным кулером и перегревом БП, т.к. до стоковой прошивки не откатиться, разрабы этот момент не продумали. Считаю это минусом, понятно что сам виноват и не проштудировал мануал англоязычный , но все же это их упущение.
Изменено 23 Aug 2022, 01:38 пользователем Vadike84
Ссылка на комментарий
Поделиться на другие сайты
-
- Поделиться
@Vadike84
1 час назад, Vadike84 сказал:
В любой, перегрейте БП и увидите ошибку
Номер ошибки можете сказать?
Ссылка на комментарий
Поделиться на другие сайты
-
- Поделиться
Здравствуйте,
В инструкции написано. Обновлять БП нужно только для иммерсионной среды.
Ссылка на комментарий
Поделиться на другие сайты
- 4 недели спустя…
-
- Поделиться
В 23.08.2022 в 11:17, BERCUD75 сказал:
@Vadike84
В 23.08.2022 в 09:30, Vadike84 сказал:
В любой, перегрейте БП и увидите ошибку
Номер ошибки можете сказать?
Сам себе отвечу. Видимо Ошибка 275. Описание появилось в новых описаниях ошибок, в старых не было такой.
Ссылка на комментарий
Поделиться на другие сайты
Для публикации сообщений создайте учётную запись или авторизуйтесь
Вы должны быть пользователем, чтобы оставить комментарий
Войти
Уже есть аккаунт? Войти в систему.
Войти
-
Последние посетители
0 пользователей онлайн
- Ни одного зарегистрированного пользователя не просматривает данную страницу
-
Similar Topics
-
Whatsminer m21, m21s
Здравствуйте, не могу создать SD карту для прошивки Whatsminer m21s. Во время создания флешки нет строчки Bootloader, флешка получается пустая, если вставить в асик то асик не прошивается диоды не светятся. И у кого открывается программа нормально не можете подсказать надписи кнопок в программе. В приложении отображения программы у меня
24 Oct 2021, 15:39
в ASIC/FPGA майнеры
-
-
TTpukoJlucT
-
8 Apr 2023, 17:26
-
-
Whatsminer M3
Официальный сайт | Mail | Instagram | Twitter
В теме действуют все Правила форума!
Перед тем как задать вопрос, посмотрите НОВИЧКИ Bits.Media, все сюда, F.A.Q по майнингу. Уважайте своё и чужое время.
Для обсуждения и поиска программ/драйверов пользуйтесь разделом Файлы.
Сообщения, не относящиеся к теме обсуждения (оффтоп), удаляются без предупреждения.
Технические характеристики:
Статьи на Bits.media:
Фото:
Обзоры
29 Oct 2017, 06:08
в ASIC/FPGA майнеры
-
-
mrizl
-
7 Apr 2023, 08:36
-
-
Whatsminer M31, M32
Есть задача добраться до файлов с логами. чтобы периодически их копировать. Скачали WinSCP и дальше вопросы. как подключаться. Пробовали по порту 443. Вроде подключение есть, но выходит в ошибку. Подскажите как подключение сделать
21 Jun 2021, 10:15
в ASIC/FPGA майнеры
-
-
Bashka92
-
4 Mar 2023, 15:49
-
-
Чипы KF1921 для Whatsminer
Всем доброго времени суток. Подскажите, пожалуйста. Чипов KF1921 есть 4 разновидности — 03C, 03G, 09C и 09G. Хотелось бы узнать в чем отличие данных чипов? Например, будет ли работать хеш-плата, если при ремонте использовать эти чипы вперемешку?
4 Feb 2021, 18:58
в ASIC/FPGA майнеры
-
-
axt
-
25 Feb 2023, 13:54
-
-
Whatsminer M20S
Всем привет.
Пытаюсь починить блок питания Whatsminer M20S
P21-12-3600-V1
12V-258AРазобрал.
Термисторы взорвалилсь.
прозвонил диодные мостики — живые!
дальше коротыш…
Стоят такие вот транзисторы:
маркировка
QSG60R074HZ
гуголь не дал ответа
может подскажете чем их заменить?
5 Jun 2022, 11:47
в Блоки питания, ИБП, силовая часть
-
-
BERCUD75
-
20 Jan 2023, 09:49
-
-
In this guide, we list some common error codes of the MicroBT WhatsMiner series and how to deal with them.
Whatsminers have a reputation for excellent build quality and high reliability. When a miner is not operating as expected, the whatsminer web UI and whatsminer tool display numerical error codes. Checking for error codes on a regular basis is crucial. Proactively addressing these problems can save money by preventing damage to the ASIC chips on the hashboards, which would require expensive repairs.
A large portion of troubleshooting involves locating a defective component, such as a slow fan, failed control board, or faulty power supply, and replacing it.
Sometimes the error codes are due to problems with hashboards. By switching the hashboards between slots and checking to see if the issue spreads there, you can determine whether a hashboard is broken. The image below displays the whatsminer hashboard numbering scheme.
If you have a faulty hashboard or a miner that needs to be repaired, we advise taking it to a Whatsminer-authorized repair facility. The video below demonstrates how to disassemble the miner in order to remove the hashboards. Additionally, this post includes a comprehensive list of error codes and troubleshooting advice.
Here is the WhatsMiner error code checklist, which we strongly advise every WhatsMiner user to keep on hand since it can help with nearly 80% of issues.
It should be beneficial to all WhatsMiner users, we hope. Please contact us if you have any further issues; we are happy to assist.
Meaning of Error Code and Corresponding Solutions on WhatsMiner Tool 1 | ||
Error Code | Meaning | Corresponding Solutions |
110 | Inlet fan detcction speed error | Check whether the fan connction is normal, or replace the power supply, or replace the fan |
111 | Outlet fan detection speed error | Check whether the fan connction is normal, or replace the power supply, or replace the fan |
120 | Inlet fan speed error(Deviation 2000+) | Check whether the fan connction is normal, or replace the power supply, or replace the fan |
121 | Outlet fan speed error(Deviation 2000+) | Check whether the fan connction is normal, or replace the power supply, or replace the fan |
130 | Inlet fan speed error | Check whether the fan connction is normal, or replace the power supply, or replace the fan |
131 | Outlet fan spced error | Check whether the fan connction is normal, or replace the power supply, or replace the fan |
140 | Fan speed is too high | Please check the environment temperature |
200 | Power detection error | Detecting the power output cable, or updating the latest Whatsminer firmware, or replacing the power supply |
201 | Power does not match the configuration file | Updating to the latest software |
202 | Power output voltage error | Updating to the latest software or check the power supply |
203 | Power supply protection | Please check the environment temperature |
204 | Power supply current protection | Please check the environment temperature |
205 | Power current error | Inspection of power supply in power grid |
206 | Power input voltage is low | Improve power supply conditions and input voltage |
207 | Power input current protecting | Improve power supply conditions and input voltage |
210 | Power status error | Check the power failure code |
213 | Power input voltage and current do not match the power | Replace the PSU |
216 | Power remained unchanged for a long time | Replace the PSU |
217 | Power set enable error | Replace the PSU |
218 | Power input voltage is lower than 230V for high power mode | Increase input voltage,replace power supply |
233 | Overtemperature Protection of Power Output | Plcase check the environment temperature |
234 | Overtemperature Protection of Power Output | Plcase check the environment temperature |
235 | Overtemperature Protection of Power Output | Plcase check the environment temperature |
236 | Overcurrent Protection of Power Output | Please check the environment temperature and the copper wire screw(Recommend to use the protable electric screwdriver) |
237 | Overcurrent Protection of Power Output | Please check the environment temperature and the copper wire screw(Recommend to use the protable electric screwdriver) |
238 | Overcurrent Protection of Power Output | Please check the environment temperature and the copper wire screw(Recommend to use the protable electric screwdriver) |
239 | Overvoltage Protection of Power Output | Check grid power |
240 | Low Voltage Protection for Power Output | Check grid power |
241 | Power output current imbalance | Replace the power |
243 | Over-tempcrature Protection for Power Input | Please check the environment temperature |
244 | Over-temperature Protection for Power Input | Please check the environment temperature |
245 | Over-tempcrature Protection for Power Input | Please check the environment temperature |
246 | Overcurrent Protection for Power Input | Please check the environment temperature |
247 | Overcurrent Protection for Power Input | Please check the environment temperature |
248 | Overvoltage Protection for Power Input | Check grid power |
249 | Overvoltage Protection for Power Input | Check grid power |
250 | Undervoltage Protection for Power Input | Check grid power |
251 | Undervoltage Protection for Power Input | Check grid power |
253 | Power Fan Error | Replace the power supply |
254 | Power Fan Error | Replace the power supply |
255 | Protection of over power output | Please check the environment temperature |
256 | Protection of over power output | Please check the environment temperature |
257 | Input over current protection of power supply primary side | Try to power off and restart, no effect to replace the power supply |
263 | Power communication warning | Check whether the screws of the control board are locked |
264 | Power communication error | Check whether the screws of the control board are locked |
267 | Power watchdog protection | Contact the technician in time |
268 | Power output over-current protection | Check the ambient temperature, check the copper bar screw |
269 | Power input over-current protection | Improve power supply conditions and input voltage |
270 | Power input over-voltage protection | Inspection of input voltage in power grid |
271 | Power input under-voltage protection | Inspection of input voltage in power grid |
272 | Warning of excessive power | Please check the environment temperature |
output of power supply | Please check the environment temperature | |
273 | Power input power too high warning | |
274 | Power fan warning | Check if the power fan is blocked and may need to be replaced |
275 | Power over temperature warning | Please check the environment temperature |
Meaning of Error Code and Corresponding Solutions on WhatsMiner Tool 2 | ||
Error Code | Meaning | Corresponding Solutions |
300 | SM0 temperature sensor detection error | Check the connection of the hash board |
301 | SM1 temperature sensor detection error | Check the connection of the hash board |
302 | SM2 temperature sensor detection error | Check the connection of the hash board |
320 | SM0 board temperature sensor communication error | Check if the control panel screws are locked, check the adapter plate and the cable contacts |
321 | SM1 board temperature sensor communication error | Check if the control panel screws are locked, check the adapter plate and the cable contacts |
322 | SM2 board temperature sensor communication error | Check if the control panel screws are locked, check the adapter plate and the cable contacts |
329 | Control board temperature sensor communication error | Replace the power supply |
350 | SM0 tempcrature protection | Check the environment temperature (Recommend to use the GS320 infrared thermometer) |
351 | M1 tempcrature protection | Check the environment temperature (Recommend to use the GS320 infrared thermometer) |
352 | SM2 tempcrature protection | Check the environment temperature (Recommend to use the GS320 infrared thermometer) |
360 | The temperature of the hash board is overheating | Check the environment temperature (Recommend to use the GS320 infrared thermometer) |
410 | SMO detect eeprom error | Check adapter plate and cable contact |
411 | SM1 detect eeprom error | Check adapter plate and cable contact |
412 | SM2 detect eeprom error | Check adapter plate and cable contact |
420 | SM0 parser eeprom error | Upgrade firmware |
421 | SM1 parser eeprom error | Upgrade firmware |
422 | SM2 parser eeprom error | Upgrade firmware |
430 | SM0 chip bin type error | Upgrade firmware |
431 | SM1 chip bin type error | Upgrade firmware |
432 | SM2 chip bin type error | Upgrade firmware |
440 | SM0 eeprom chip num X error | Upgrade firmware |
441 | SM1 eeprom chip num X error | Upgrade firmware |
442 | SM2 eeprom chip num X error | Upgrade firmware |
450 | SM0 eeprom xfer error | Check adapter board and wiring contacts.Upgrade firmware |
451 | SM1 eeprom xfer error | Check adapter board and wiring contacts.Upgrade firmware |
452 | SM2 eeprom xfer error | Check adapter board and wiring contacts.Upgrade firmware |
510 | SM0 miner type error | The version and type of hashboard are inconsistent, replace the correct hashboard |
511 | SM1 miner type error | The version and type of hashboard are inconsistent, replace the correct hashboard |
512 | SM2 miner type error | The version and type of hashboard are inconsistent, replace the correct hashboard |
520 | SM0 bin type error | Change the hash board with the appropriate one if the chip type is inconsistent. |
521 | SM1 bin type error | Change the hash board with the appropriate one if the chip type is inconsistent. |
522 | SM2 bin type error | Change the hash board with the appropriate one if the chip type is inconsistent. |
530 | SM0 board is not detected | Check the adapter board wiring and cablc, or replace the control board to check whether the hash board connector is soldered |
531 | SM1 board is not detected | Check the adapter board wiring and cablc, or replace the control board to check whether the hash board connector is soldered |
532 | SM2 board is not detected | Check the adapter board wiring and cablc, or replace the control board to check whether the hash board connector is soldered |
540 | The number of SM0 chips is incomplete | Check adapter plate and cable contact |
541 | The number of SM1 chips is incomplete | Check adapter plate and cable contact |
542 | The number of SM2 chips is incomplete | Check adapter plate and cable contact |
550 | SM0 has bad chips | Replace the bad chip in the print position |
551 | SM1 has bad chips | Replace the bad chip in the print position |
552 | SM2 has bad chips | Replace the bad chip in the print position |
560 | SM0 loss balance | Plug in the adapter plate, and then screw in the power connection hash board again |
561 | SM1 loss balance | Plug in the adapter plate, and then screw in the power connection hash board again |
562 | SM2 loss balance | Plug in the adapter plate, and then screw in the power connection hash board again |
590 | SM0 frequency is too low | Replace the hash board and place the hash boards which reported the same error together |
591 | SM1 frequency is too low | Replace the hash board and place the hash boards which reported the same error together |
592 | SM2 frequency is too low | Replace the hash board and place the hash boards which reported the same error together |
600 | Environment temperature is too high | Check the environment temperature |
610 | If the ambient temperature is too high in high performance mode, return to normal mode | Check the ambient temperature, high performance mode needs to be ontrolled below 30 ℃ |
701 | Control board no support chip | Upgrade the corresponding type of firmware |
710 | Control board error | Update to the latest firmware |
712 | Control board rebooted as exception | Updating the latest firmware.Check whether the control board screw is locked properly |
800 | cgminer checksum error | Re-upgrade firmware |
801 | system-monitor checksum error | Re-upgrade firmware |
802 | system-monitor checksum error | Re-upgrade firmware |
2000 | No pool information configured | Check pool configuration |
2010 | All mining pool connections failed | Check the network or mining pools setting |
2020 | Mining pool0 connection failed | Check the network or mining pools setting |
2021 | Mining pool1 connection failed | Check the network or mining pools setting |
2022 | Mining pool2 connection failed | Check the network or mining pools setting |
2030 | Mining pool rejcction rate is too high | Check the network or mining pool setting, and the mining setting of the cryptocurrency |
2040 | The pool does not support the asicboost mode | Check pool configuration |
2310 | Hash rate is too low | Check input voltage, network environment, and ambient temperature |
2320 | Hash rate is too low | Check input voltage, network environment, and ambient temperature |
2340 | The loss of hash rate is too high | Check input voltage, network environment, and ambient temperature |
2350 | The loss of hash rate is too high | Check input voltage, network environment, and ambient temperature |
5070 | SM0 water velocity is abnormal | Check if the water flow is normal |
5071 | SM1 water velocity is abnormal | Check if the water flow is normal |
5072 | SM2 water velocity is abnormal | Check if the water flow is normal |
5110 | SM0 Frequency Up Timeout | reboot |
5111 | SM1 Frequency Up Timeout | reboot |
5112 | SM2 Frequency Up Timeout | reboot |
8410 | Software version error (M2x miner with M3x firmware, or M3x with M2x firmware) | Upgrade to the correct firmware version |
100001 | /antiv/signature Illegal | Upgrade the latest firmware or burn the card |
100002 | /antiv/dig/initd.dig Illegal | Upgrade the latest firmware or burn the card |
100003 | /antiv/dig/pf_partial.dig Illegal | Upgrade the latest firmware or burn the card |
PSU Error code | Reason | processing method |
0x0001 | Input undervoltage | Check the power supply |
0x0002 | Temperature sampling over temperature protection of power radiator | 10 minutes after a power outage, turn the power back on. If it occurs again, replace the power supply |
0x0004 | Temperature sampling over temperature protection of power radiator | 10 minutes after a power outage, turn the power back on. If it occurs again, replace the power supply |
0x0008 | Over temperature protection of environmental emperature sampling in power supply | 10 minutes after a power outage, turn the power back on. If it occurs again, replace the power supply |
0x0010 | Primary side over current | After a 10 minute power outage, turn the power back on. If it occurs again, replace the power supply |
0x0020 | Output undervoltage | Check the power supply |
0x0040 | Output over current (continuous load 320A for more than 2S) | Tighten the copper bar screw again |
0x0080 | Primary side over current | 10 minutes after a power outage, turn the power back on. If it occurs again, replace the power supply |
0x0100 | Single circuit overcurrent (protection point 120a) | Check the PSU |
0x0200 | Single circuit overcurrent (protection point 120a) | Check the PSU |
0x0400 | Single circuit overcurrent (protection point 120a) | Check the PSU |
0x0800 | Fan failure | Replace the PSU |
0x1000 | Output over current (continuous load of 310A for more than 5min) | Check the PSU |
0x2000 | Output over current (continuous load 295A for more than 10min) | Check the PSU |
All WhatsMiner users should find it useful, we hope. Please get in touch with us if you have any other issues; we’ll be happy to assist.
300 Ошибка обнаружения датчика температуры SM0 Проверьте подключение хэш-платы 301 Ошибка обнаружения датчика температуры SM1
302 Ошибка обнаружения датчика температуры SM2
320 Ошибка связи с датчиком температуры платы SM0 Проверьте, заблокированы ли винты панели управления, проверьте переходную пластину и контакты кабеля 321 Ошибка связи с датчиком температуры платы SM1
322 Ошибка связи с датчиком температуры платы SM2
329 Температура платы управления ошибка связи с датчиком Замените источник питания 350 Защита от перегрева SM0 Проверьте температуру окружающей среды (рекомендуется использовать инфракрасный термометр GS320). 351 SM1 защита от перегрева
352 SM2 защита от перегрева
360 Температура хэш-платы перегревается
410 SMO обнаружило ошибку eeprom Проверьте переходную пластину и контакт кабеля 411 SM1 обнаружило ошибку eeprom
412 SM2 обнаружило ошибку eeprom
420 SM0 ошибка синтаксического анализатора eeprom Обновить прошивку 421 SM1 ошибка синтаксического анализатора eeprom
422 M2 ошибка eeprom синтаксического анализатора
430 Ошибка типа бина микросхемы SM0
431 Ошибка типа бина микросхемы SM1
432 Ошибка типа буфера микросхемы SM2
440 Ошибка SM0 eeprom chip num X
441 Ошибка SM1 eeprom chip num X
442 SM2 номер микросхемы eeprom X ошибка
450 SM0 eeprom xfer error Проверьте плату адаптера и контакты проводки.Обновите прошивку
451 SM1 eeprom xfer error
452 SM2 eeprom xfer error
510 SM0 ошибка типа майнера Версия и тип хэшборда несовместимы, замените правильный хэшборд
511 SM1 ошибка типа майнера
512 Ошибка типа майнера SM2
520 Ошибка типа бина SM0 Если тип чипа хэш-платы несовместим, замените правильную хэш-плату
521 Ошибка типа бина SM1
522 Ошибка типа бина SM2
530 Плата SM0 не обнаружена Проверьте проводку платы адаптера и кабель, или замените плату управления, чтобы проверить, припаян
ли
разъем хэш-платы.
531 Плата SM1 не обнаружена
532 Плата SM2 не обнаружена
540 Количество микросхем SM0 неполное Проверьте переходную пластину и контакт кабеля
541 Количество микросхем SM1 неполное
542 Количество микросхем SM2 неполное
550 SM0 имеет плохие чипы Замените плохую микросхему в позиции печати
551 SM1 имеет плохие чипы
552 SM2 имеет плохие чипы
560 SM0 потеря баланса Подключите переходную пластину, а затем снова прикрутите хэш-плату для подключения питания
561 SM1 потеря баланса
562 SM2 потеря баланса
590 Частота SM0 слишком низкая Замените хэш-плату и поместите вместе хэш-платы, которые сообщили об одной и той же ошибке
591 Частота SM1 слишком низкая
592 Частота SM2 слишком низкая
600 Слишком высокая температура окружающей среды Проверьте температуру окружающей среды
610 Если температура окружающей среды слишком высока в режиме высокой производительности, вернитесь в
нормальный
режим Проверьте температуру окружающей среды, в режиме высокой производительности должна быть ниже 30 ℃.
701 На плате управления отсутствует микросхема поддержки Обновление соответствующего типа микропрограммы
710 Ошибка платы управления Обновите до последней версии прошивки
712 Плата управления перезагрузилась как исключение Обновление последней версии прошивки. Проверьте, правильно ли зафиксирован винт платы управления 800 Ошибка контрольной суммы cgminer Обновление микропрограммы 801 Ошибка контрольной суммы системного монитора
802 Ошибка контрольной суммы системного монитора
2000 Не настроена информация о пуле Проверьте конфигурацию пула 2010 Все подключения к пулам майнинга не удались Проверьте настройки сети или пулов майнинга 2020 Не удалось установить соединение с пулом майнинга
2021 Не удалось установить соединение с пулом майнинга 2022 Не удалось установить соединение с пулом майнинга
2030 Скорость повторного срабатывания пула майнинга слишком высока Проверьте настройки сети или пула майнинга, а также настройки майнинга криптовалюты 2040 Пул не поддерживает режим asicboost Проверьте конфигурацию пула 2310 Хэшрейт слишком низкий Проверьте входное напряжение, сетевое окружение и температуру окружающей среды. 2320 Скорость хэширования слишком низкая
2340 Потеря хэшрейта слишком высока
2350 Потеря скорости хэширования слишком высока
5070 Скорость потока воды SM0 ненормальная Проверьте, нормальный ли поток воды 5071 SM1 Скорость течения воды ненормальная
5072 SM2 Скорость потока воды ненормальная
5110 SM0 Таймаут повышения частоты Перезагрузите 5111 SM1 Таймаут повышения частоты
5112 SM2 Таймаут повышения частоты
8410 Ошибка версии программного обеспечения (miner M2x с прошивкой M3x или M3x с прошивкой M2x) Обновление до правильной версии прошивки 100001 /antiv/signature illegal Обновление до последней версии микропрограммы или запись карты 100002 /antiv/dig/initd.dig illegal Обновление до последней версии микропрограммы или запись карты 100003 /antiv/dig/pf_partial.dig illegal Обновление до последней версии микропрограммы или запись карты
Коды ошибок асик майнера WhatsMiner
0 ErrSucc ОК ОК — обычный
21 ErrNotPlugged 1 или более хеш-плат не обнаружены Сигнал Hashboard PLUG не обнаружен Номер обнаруженной платы питания, если их более одной, разделенные пробелами 1. Проверьте правильность подключения кабеля SPI (по сравнению с обычной машиной) и снова подключите кабель. 2. Замените плату управления. 3. Замените проблемную доску хешрейта (переделайте доску головоломки).
22 ErrPsuI2cFail Аномальная связь по управлению питанием Неправильная связь I2C источника питания — 1. Заменить блок питания. 2. Замените плату управления.
23 ErrEncoreAllFail Все хэш-платы не могут быть включены SPI недоступен для всех плат хешрейта — 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Отремонтируйте всю машину.
24 ErrEncoreFail Некоторые платы не включаются SPI недоступен на некоторых хэш-досках Номер хэшборда, для которого произошел сбой связи по SPI, если их несколько, разделенных пробелами 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Замените проблемную хеш-доску (переделайте доску-головоломку).
25 ErrSetPllFail Не удалось поднять частоту хэш-платы Не удалось поднять частоту хэш-платы Номер хэшборда: частота ошибок 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Замените проблемную хеш-доску (переделайте доску-головоломку).
26 ErrSetVolFail Не удалось установить напряжение Не удалось установить напряжение Номер хэшборда: 1/2 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Заменить проблемную хеш-доску (присоединиться)
27 ErrBistFail Тест чипа BIST не пройден Тест чипа BIST не пройден Номер хэшборда: 1/2 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить проблемную хеш-доску (присоединиться к плате)
28 ErrSpiFail Ненормальная связь платы хешрейта не может быть автоматически восстановлена ??во время работы Ненормальное соединение SPI платы хешрейта не может быть автоматически восстановлено во время работы Номер хэшборда 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Замените проблемную хеш-доску (переделайте доску-головоломку)
29 ErrI2cFail Ненормальная связь по питанию во время работы не может быть восстановлена ??автоматически Связь I2C с ненормальным источником питания не может быть автоматически восстановлена ??во время работы — 1. Заменить блок питания. 2. Замените плату управления.
30 ErrNetwork Подключение к майнинговому пулу прервано Подключение к майнинговому пулу прервано — Если эта проблема возникает на большом количестве или на всех майнинговых машинах с одним и тем же коммутатором: 1. Проверьте правильность настроек пула для майнинга. 2. Проверьте конфигурацию сетевой среды (например, конфигурацию DHCP, конфигурацию DNS, порт и т. Д.). Если проблемы возникают только на одной или нескольких машинах для майнинга: 1. Проверьте правильность настроек пула для майнинга. 2. Проверить подключения к сетевому порту майнера. 3. Замените сетевой кабель на работающую майнинговую машину. 4. Замените плату управления.
31 ErrBadChip Повреждение отдельных микросхем, что приводит к искусственно завышенной вычислительной мощности Повреждение отдельных микросхем, что приводит к искусственно завышенной вычислительной мощности Номер поврежденной микросхемы: номер хеш-платы, если их более одной, разделенные пробелами В ремонт
32 ErrOverheat Hashboard перегрелся Hashboard перегрелся Номер хэшборда 1. Проверьте, вращаются ли передний и задний вентиляторы, если они не вращаются, сначала замените вентиляторы, а затем замените плату управления / блок питания. 2. Убедитесь, что направление ветра спереди и сзади согласовано, согласуется ли оно с другими машинами, если нет, измените направление вентилятора. 3. Если температура воздуха на входе горной машины превышает 40 градусов, необходимо улучшить температурную среду в шахте. 4. Если определенная плата хешрейта часто перегревается, вы можете заменить проблемную плату хешрейта (переделайте головоломку).
33 ErrInvTemp Невозможно прочитать температуру чипа Невозможно прочитать температуру чипа Номер хэшборда 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Замените проблемную хеш-доску (переделайте доску-головоломку).
34 ErrMisPlugged Неправильное подключение кабеля связи платы управления Ненормальное подключение кабеля SPI платы управления Номер хэшборда 1. Проверьте, совместим ли метод (последовательность) подключения кабеля SPI хэш-платы с другими машинами той же модели. 2. Замените плату управления.
35 ErrPsuFail Аномальный источник питания Аномальный источник питания 1. Обратите внимание на то, что если нет явного отклонения от нормы вычислительной мощности всей машины (не отключается плата), то перезагрузить 2. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 3. Заменить блок питания.
36 ErrInvCorenum Некоторые чипы не работают должным образом Количество хороших фишек ненормальное Номер хэшборда: номер чипа 1. Обратите внимание на то, что если нет явного отклонения от нормы вычислительной мощности всей машины (не отключается плата), то перезагрузить 2. Перезапустите майнер, чтобы увидеть, появляется ли по-прежнему та же ошибка. 3. Замените проблемную хеш-плату.
37 ErrInvVidtype Тип платы управления / версия прошивки / количество микросхем не совпадает Тип платы управления / версия прошивки / количество микросхем не совпадает vidtype, minertype, subtype, chipnum После накопления нескольких единиц (> 10) обратитесь в ремонт.
38 ErrBadRearChips Наконец, у некоторых чипов низкая вычислительная мощность. Последние несколько уровней чипов имеют низкую вычислительную мощность В ремонт
39 ErrInvTuneParam Аномальные параметры старения Напряжение начальной частоты старения неверно В ремонт
Errcode | Scope of application | Explanation | Troubleshooting steps |
0 | Whole miner | Normal | Normal |
21 | hashboard | one or more hashboards can’t be detected | 1. check and see whether the SPI cables are firmly and correctly connected (compared the connection of cables with working miners), reconnect the SPI cables, don’t change sequence of connection 2. replace control board with other well functional one 3. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
22 | Whole miner | PSU communication is abnormal | 1. replace PSU with other well functional one 2. replace control board with other well functional one |
23 | Whole miner | All hashboards can’t be powered up | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. whole miner should be returned for repair |
24 | hashboard | one or more hashboards can’t be powered up | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
25 | hashboard | frequency increase of hashboards fails | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check and see whether screws on the PSU side and SPI connection are loose 3. replace PSU with other well functional one 4. replace control board with other well functional one 5. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
26 | hashboard | voltage setting fails | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
27 | hashboard | chip BIST test fails | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
28 | hashboard | abnormal communication of hashboard, it can’t be automatically recovered when running | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
29 | Whole miner | abnormal communication of PSU can’t be automatically recovered when running | 1. replace PSU with other well functional one 2. replace control board with other well functional one |
30 | Whole miner | pool disconnect | If the problem occurs in a large number of miners or all of the mines under the same switch: 1. please first check whether pool setting is correct 2. then check network configuration (such as DHCP configuration, DNS configuration, ports, etc.) If the problem occurs in only one or just a small number of miners under the same switch: 1. please first check whether pool setting is correct 2. then check whether network cable is firmly connected 3. replace network cable with other one from other well working miner 4. replace control board with other well functional one |
31 | hashboard | damage of some individual chip causes inflated high hashrate of the miner | no action should be taken |
32 | hashboard | hashboard overheat | 1. check and see whether both fans are spinning, if not, replace fan with other functional one, if still not, then replace control board or PSU 2. check and see whether wind direction of both fans are the same, whether wind direction are the same with other miners, if not, exchange fans 3. meter the inlet temperature of the miner, if above 40 °C, cooling system of the mining farm should be improved 4. if some hashboard is overheated frequently, that hashboard should be replaced (returned for repair) |
33 | hashboard | chip temperature can’t be read | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
34 | cables of control board is connected incorrectly | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check whether hashboard SPI cables are conneted in the same way (sequence) as other miners of same model 3. replace control board with other well functional one |
|
35 | hashboard | PSU voltage is too low | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2.check and see whether screws on the PSU side and SPI connection is loose 3. replace PSU with other well functional one |
36 | hashboard | working or some chips is abnormal | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. reboot the miner to see whether the same error is given 3. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
37 | Whole miner | mismatch of control board version/firmware version/quantity of chips | if there are more than 10 miners with same error, please contact engineers |
38 | hashboard | low hashrate of last few chips | no action should be taken |
39 | hashboard | testing parameter is abnormal | no action should be taken |
40 | hashboard | PSU load is insufficient | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
41 | hashboard | startup voltage of PSU is too low | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check and see whether screws on the PSU side and SPI connection are loose 3. replace PSU with other well functional one 4. replace control board with other well functional one |
42 | hashboard | implementation of plan B fails when hashboard frequency increases | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check and see whether screws on the PSU side and SPI connection are loose 3. replace PSU with other well functional one 4. replace control board with other well functional one 5. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
Attention: 1. The miner should be powered up again to see whether it is back to normal after every step is taken 2. If the problem is not solve after replacement the part, the part should go back to its original unit 3. Error code and brief description of the problem should be attached to the hashboard that is confirmed defective and that will be returned for repair |
Error
code
Reason Processing method
110 Fanin detect speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
fan
111 Fanout detect speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
fan
130 Fanin speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
fan
131 Fanout speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
fan
140 Fan speed is too high Please check the environment temperature
200
Power probing error, no
power found
Detecting power output wiring, updating the
latest firmware, or replacing power supply
201
Power supply and
configuration file
mismatch
Replace the correct PSU
203 Power protecting Please check the environment temperature
204 Power current protecting Please check the environment temperature
205 Power current error Inspection of power supply in power grid
206 Power input voltage is low
Improve power supply conditions and input
voltage
207
Power input current
protecting
Improve power supply conditions and input
voltage
210 Power error status Check power failure code
213
Power input voltage and
current do not match the
power
Replace the PSU
233
Power output over
temperature protection
Please check the environment temperature
234
Power output over
temperature protection
Please check the environment temperature
235
Power output over
temperature protection
Please check the environment temperature
236
Overcurrent Protection of
Power Output
Please check the environment temperature,
check copper row screw
237
Overcurrent Protection of
Power Output
Please check the environment temperature,
check copper row screw
238
Overcurrent Protection of
Power Output
Please check the environment temperature,
check copper row screw
239
Overvoltage Protection of
Power Output
Inspection of power supply in power grid
240
Low Voltage Protection for
Power Output
Inspection of power supply in power grid
241
Power output current
imbalance
Replace the power
243
Over-temperature
Protection for Power Input
Please check the environment temperature
244
Over-temperature
Protection for Power Input
Please check the environment temperature
245
Over-temperature
Protection for Power Input
Please check the environment temperature
246
Overcurrent Protection for
Power Input
Please check the environment temperature
247
Overcurrent Protection for
Power Input
Please check the environment temperature
248
Overvoltage Protection for
Power Input
Inspection of input voltage in power grid
249
Overvoltage Protection for
Power Input
Inspection of input voltage in power grid
250
Undervoltage Protection
for Power Input
Inspection of input voltage in power grid
251
Undervoltage Protection
for Power Input
Inspection of input voltage in power grid
253 Power Fan Error Replace the PSU
254 Power Fan Error Replace the PSU
255
Protection of over power
output
Please check the environment temperature
256
Protection of over power
output
Please check the environment temperature
257
Input over current
protection of power supply
primary side
Try to power off and restart, no effect to
replace the power supply
263
Power communication
warning
Check whether the screws of the control
board are locked
264 Power communication error
Check whether the screws of the control
board are locked
267 Power watchdog protection Contact the technician in time
268
Power output over-current
protection
Check the ambient temperature, check the
copper bar screw
269
Power input over-current
protection
Improve power supply conditions and input
voltage
270
Power input over-voltage
protection
Inspection of input voltage in power grid
271
Power input under-voltage
protection
Inspection of input voltage in power grid
272
Warning of excessive power
output of power supply
Please check the environment temperature
273
Power input power too high
warning
Please check the environment temperature
274 Power fan warning
Check if the power fan is blocked and may
need to be replaced
275
Power over temperature
warning
Please check the environment temperature
300
SM0 temperature sensor
detection error
Check the connection of the hashboard
301
SM1 temperature sensor
detection error
Check the connection of the hashboard
302
SM2 temperature sensor
detection error
Check the connection of the hashboard
320
SM0 temperature reading
error
Check whether the control board screw is
locked properly, check the connection board
and the arrangement contact
321
SM1 temperature reading
error
Check whether the control board screw is
locked properly, check the connection board
and the arrangement contact
322
SM2 temperature reading
error
Check whether the control board screw is
locked properly, check the connection board
and the arrangement contact
329
Control board temperature
sensor communication error
Replace the power supply
350 SM0 temperature protecting Please check the environment temperature
351 SM1 temperature protecting Please check the environment temperature
352 SM2 temperature protecting Please check the environment temperature
410 SM0 detect eeprom error Check adapter board and wiring contact
411 SM1 detect eeprom error Check adapter board and wiring contact
412 SM2 detect eeprom error Check adapter board and wiring contact
420 SM0 parser eeprom error Contact the technician in time
421 SM1 parser eeprom error Contact the technician in time
422 SM2 parser eeprom error Contact the technician in time
430 SM0 chip bin type error Contact the technician in time
431 SM1 chip bin type error Contact the technician in time
432 SM2 chip bin type error Contact the technician in time
440
SM0 eeprom chip num X
error
Contact the technician in time
441
SM1 eeprom chip num X
error
Contact the technician in time
442
SM2 eeprom chip num X
error
Contact the technician in time
510 SM0 miner type error
The version and type of hashboard are
inconsistent, replace the correct hashboard
511 SM1 miner type error
The version and type of hashboard are
inconsistent, replace the correct hashboard
512 SM2 miner type error
The version and type of hashboard are
inconsistent, replace the correct hashboard
530 SM0 not found
Check the connection and arrangement of the
adapter board, or replace the control
board, check whether the hash board
connector is empty welded
531 SM1 not found
Check the connection and arrangement of the
adapter board, or replace the control
board, check whether the hash board
connector is empty welded
532 SM2 not found
Check the connection and arrangement of the
adapter board, or replace the control
board, check whether the hash board
connector is empty welded
540 SM0 reading chip id error
Check adapter board and wiring contact,
Clean the dust on the hashboard
541 SM1 reading chip id error
Check adapter board and wiring contact,
Clean the dust on the hashboard
542 SM2 reading chip id error
Check adapter board and wiring contact,
Clean the dust on the hashboard
550 SM0 have bad chips Replacement of bad chips
551 SM1 have bad chips Replacement of bad chips
552 SM2 have bad chips Replacement of bad chips
560 SM0 loss balance
Plug in the adapter plate, and then screw
in the power connection hashboard again
561 SM1 loss balance
Plug in the adapter plate, and then screw
in the power connection hashboard again
562 SM2 loss balance
Plug in the adapter plate, and then screw
in the power connection hashboard again
600
Environment temperature is
high
Please check the environment temperature
610
If the ambient temperature
is too high in high
performance mode, return
to normal mode
Check the ambient temperature, high
performance mode needs to be controlled
below 30 ?
710
Control board rebooted as
exception
Updating the latest firmware.Check whether
the control board screw is locked properly
800 cgminer checksum error Re-upgrade firmware
801
system-monitor checksum
error
Re-upgrade firmware
802
remote-daemon checksum
error
Re-upgrade firmware
2010 All pools are disable Please check the network or pools configure
2020 Pool0 connect failed Please check the network or pools configure
2021 Pool1 connect failed Please check the network or pools configure
2022 Pool2 connect failed Please check the network or pools configure
2030
High rejection rate of
pool
Please check the network or pools
configure.Setting of mining currency
2040
The pool does not support
the asicboost mode
Check pool configuration
5110 SM0 Frequency Up Timeout reboot
5111 SM1 Frequency Up Timeout reboot
5112 SM2 Frequency Up Timeout reboot
8410
Software version error
(M2x miner with M3x
firmware, or M3x with M2x
firmware).
Upgrade to the correct firmware version
PSU
Error
code
Reason processing method
0x0001 Input undervoltage Check the power supply
0x0002
Temperature sampling over
temperature protection of
power radiator
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0004
Temperature sampling over
temperature protection of
power radiator
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0008
Over temperature
protection of
environmental temperature
sampling in power supply
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0010 Primary side over current
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0020 Output undervoltage Check the power supply
0x0040
Output over current
(continuous load 320A for
more than 2S)
Tighten the copper bar screw again
0x0080 Primary side over current
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0100
Single circuit overcurrent
(protection point 120a)
Check the PSU
0x0200
Single circuit overcurrent
(protection point 120a)
Check the PSU
0x0400
Single circuit overcurrent
(protection point 120a)
Check the PSU
0x0800 Fan failure Replace the PSU
0x1000
Output over current
(continuous load of 310A
for more than 5min)
Check the PSU
0x2000
Output over current
(continuous load 295A for
more than 10min)
Check the PS
Error code Reason Processing method 110 Fanin detect speed error Check whether the fan connection is normal, or replace the power supply, or replace the fan 111 Fanout detect speed error Check whether the fan connection is normal, or replace the power supply, or replace the fan 130 Fanin speed error Check whether the fan connection is normal, or replace the power supply, or replace the fan 131 Fanout speed error Check whether the fan connection is normal, or replace the power supply, or replace the fan 140 Fan speed is too high Please check the environment temperature 200 Power probing error, no power found Detecting power output wiring, updating the latest firmware, or replacing power supply 201 Power supply and configuration file mismatch Replace the correct PSU 203 Power protecting Please check the environment temperature 204 Power current protecting Please check the environment temperature 205 Power current error Inspection of power supply in power grid 206 Power input voltage is low Improve power supply conditions and input voltage 207 Power input current protecting Improve power supply conditions and input voltage 210 Power error status Check power failure code 213 Power input voltage and current do not match the power Replace the PSU 233 Power output over temperature protection Please check the environment temperature 234 Power output over temperature protection Please check the environment temperature 235 Power output over temperature protection Please check the environment temperature 236 Overcurrent Protection of Power Output Please check the environment temperature, check copper row screw 237 Overcurrent Protection of Power Output Please check the environment temperature, check copper row screw 238 Overcurrent Protection of Power Output Please check the environment temperature, check copper row screw 239 Overvoltage Protection of Power Output Inspection of power supply in power grid 240 Low Voltage Protection for Power Output Inspection of power supply in power grid 241 Power output current imbalance Replace the power 243 Over-temperature Protection for Power Input Please check the environment temperature 244 Over-temperature Protection for Power Input Please check the environment temperature 245 Over-temperature Protection for Power Input Please check the environment temperature 246 Overcurrent Protection for Power Input Please check the environment temperature 247 Overcurrent Protection for Power Input Please check the environment temperature 248 Overvoltage Protection for Power Input Inspection of input voltage in power grid 249 Overvoltage Protection for Power Input Inspection of input voltage in power grid 250 Undervoltage Protection for Power Input Inspection of input voltage in power grid 251 Undervoltage Protection for Power Input Inspection of input voltage in power grid 253 Power Fan Error Replace the PSU 254 Power Fan Error Replace the PSU 255 Protection of over power output Please check the environment temperature 256 Protection of over power output Please check the environment temperature 257 Input over current protection of power supply primary side Try to power off and restart, no effect to replace the power supply 263 Power communication warning Check whether the screws of the control board are locked 264 Power communication error Check whether the screws of the control board are locked 267 Power watchdog protection Contact the technician in time 268 Power output over-current protection Check the ambient temperature, check the copper bar screw 269 Power input over-current protection Improve power supply conditions and input voltage 270 Power input over-voltage protection Inspection of input voltage in power grid 271 Power input under-voltage protection Inspection of input voltage in power grid 272 Warning of excessive power output of power supply Please check the environment temperature 273 Power input power too high warning Please check the environment temperature 274 Power fan warning Check if the power fan is blocked and may need to be replaced 275 Power over temperature warning Please check the environment temperature 300 SM0 temperature sensor detection error Check the connection of the hashboard 301 SM1 temperature sensor detection error Check the connection of the hashboard 302 SM2 temperature sensor detection error Check the connection of the hashboard 320 SM0 temperature reading error Check whether the control board screw is locked properly, check the connection board and the arrangement contact 321 SM1 temperature reading error Check whether the control board screw is locked properly, check the connection board and the arrangement contact 322 SM2 temperature reading error Check whether the control board screw is locked properly, check the connection board and the arrangement contact 329 Control board temperature sensor communication error Replace the power supply 350 SM0 temperature protecting Please check the environment temperature 351 SM1 temperature protecting Please check the environment temperature 352 SM2 temperature protecting Please check the environment temperature 410 SM0 detect eeprom error Check adapter board and wiring contact 411 SM1 detect eeprom error Check adapter board and wiring contact 412 SM2 detect eeprom error Check adapter board and wiring contact 420 SM0 parser eeprom error Contact the technician in time 421 SM1 parser eeprom error Contact the technician in time 422 SM2 parser eeprom error Contact the technician in time 430 SM0 chip bin type error Contact the technician in time 431 SM1 chip bin type error Contact the technician in time 432 SM2 chip bin type error Contact the technician in time 440 SM0 eeprom chip num X error Contact the technician in time 441 SM1 eeprom chip num X error Contact the technician in time 442 SM2 eeprom chip num X error Contact the technician in time 510 SM0 miner type error The version and type of hashboard are inconsistent, replace the correct hashboard 511 SM1 miner type error The version and type of hashboard are inconsistent, replace the correct hashboard 512 SM2 miner type error The version and type of hashboard are inconsistent, replace the correct hashboard 530 SM0 not found Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded 531 SM1 not found Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded 532 SM2 not found Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded 540 SM0 reading chip id error Check adapter board and wiring contact, Clean the dust on the hashboard 541 SM1 reading chip id error Check adapter board and wiring contact, Clean the dust on the hashboard 542 SM2 reading chip id error Check adapter board and wiring contact, Clean the dust on the hashboard 550 SM0 have bad chips Replacement of bad chips 551 SM1 have bad chips Replacement of bad chips 552 SM2 have bad chips Replacement of bad chips 560 SM0 loss balance Plug in the adapter plate, and then screw in the power connection hashboard again 561 SM1 loss balance Plug in the adapter plate, and then screw in the power connection hashboard again 562 SM2 loss balance Plug in the adapter plate, and then screw in the power connection hashboard again 600 Environment temperature is high Please check the environment temperature 610 If the ambient temperature is too high in high performance mode, return to normal mode Check the ambient temperature, high performance mode needs to be controlled below 30 ℃ 710 Control board rebooted as exception Updating the latest firmware.Check whether the control board screw is locked properly 800 cgminer checksum error Re-upgrade firmware 801 system-monitor checksum error Re-upgrade firmware 802 remote-daemon checksum error Re-upgrade firmware 2010 All pools are disable Please check the network or pools configure 2020 Pool0 connect failed Please check the network or pools configure 2021 Pool1 connect failed Please check the network or pools configure 2022 Pool2 connect failed Please check the network or pools configure 2030 High rejection rate of pool Please check the network or pools configure.Setting of mining currency 2040 The pool does not support the asicboost mode Check pool configuration 5110 SM0 Frequency Up Timeout reboot 5111 SM1 Frequency Up Timeout reboot 5112 SM2 Frequency Up Timeout reboot 8410 Software version error (M2x miner with M3x firmware, or M3x with M2x firmware). Upgrade to the correct firmware version PSU Error code Reason processing method 0x0001 Input undervoltage Check the power supply 0x0002 Temperature sampling over temperature protection of power radiator Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0004 Temperature sampling over temperature protection of power radiator Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0008 Over temperature protection of environmental temperature sampling in power supply Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0010 Primary side over current Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0020 Output undervoltage Check the power supply 0x0040 Output over current (continuous load 320A for more than 2S) Tighten the copper bar screw again 0x0080 Primary side over current Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0100 Single circuit overcurrent (protection point 120a) Check the PSU 0x0200 Single circuit overcurrent (protection point 120a) Check the PSU 0x0400 Single circuit overcurrent (protection point 120a) Check the PSU 0x0800 Fan failure Replace the PSU 0x1000 Output over current (continuous load of 310A for more than 5min) Check the PSU 0x2000 Output over current (continuous load 295A for more than 10min) Check the PS
Error code Reason Processing method Причина Способ устранения 110 Fanin detect speed error Check whether the fan connection is normal, or replace the power supply, or replace the
fan
Ошибка обнаружения скорости вращения вентилятора на входе Проверьте, правильно ли подключен вентилятор, исправен ли он. Замените источник питания, или замените вентилятор 111 Fanout detect speed error Check whether the fan connection is normal, or replace the power supply, or replace the
fan
Ошибка обнаружения скорости вращения вентилятора на выходе Проверьте, правильно ли подключен вентилятор, исправен ли он. Замените источник питания, или замените вентилятор 130 Fanin speed error Check whether the fan connection is normal, or replace the power supply, or replace the
fan
Ошибка скорости вращения вентилятора на входе Проверьте, правильно ли подключен вентилятор, исправен ли он. Замените источник питания, или замените вентилятор 131 Fanout speed error Check whether the fan connection is normal, or replace the power supply, or replace the
fan
Ошибка скорости вращения вентилятора на выходе Проверьте, правильно ли подключен вентилятор, исправен ли он. Замените источник питания, или замените вентилятор 140 Fan speed is too high Please check the environment temperature Слишком высокая скорость вращения вентилятора Пожалуйста, проверьте температуру окружающей среды или проверьте запыленность хэшплат 200 Power probing error, no power found Detecting power output wiring, updating the latest firmware, or replacing power supply Ошибка измерения мощности, питание не найдено Проверьте силовую проводку, обновите до последней версии встроенное программное обеспечение или замена источника питания 201 Power supply and configuration file mismatch Replace the correct PSU Несоответствие источника питания и конфигурационного файла Замените блок питания на оригинальный 203 Power protecting Please check the environment temperature Защита по питанию Пожалуйста, проверьте температуру окружающей среды 204 Power current protecting Please check the environment temperature Защита от тока питания Пожалуйста, проверьте температуру окружающей среды 205 Power current error Inspection of power supply in power grid Ошибка тока питания Проверка электроснабжения в электросети 206 Power input voltage is low Improve power supply conditions and input voltage Входное напряжение питания низкое Проверьте напряжение под нагрузкой. Улучшите условия подключения майнера 207 Power input current protecting Improve power supply conditions and input voltage Защита от входного тока питания Улучшите условия питания и входное напряжение 210 Power error status Check power failure code Состояние ошибки питания Проверьте код сбоя питания 213 Power input voltage and current do not match the power Replace the PSU Входное напряжение и ток питания не соответствуют мощности Проверьте напряжение под нагрузкой. Улучшите условия подключения майнера Замените блок питания 233 Power output over temperature protection Please check the environment temperature Защита выходной мощности от перегрева Пожалуйста, проверьте температуру окружающей среды 234 Power output over temperature protection Please check the environment temperature Защита выходной мощности от перегрева Пожалуйста, проверьте температуру окружающей среды 235 Power output over temperature protection Please check the environment temperature Защита выходной мощности от перегрева Пожалуйста, проверьте температуру окружающей среды 236 Overcurrent Protection of Power Output Please check the environment temperature, check copper row screw Защита выходной мощности от перегрузки по току Пожалуйста, проверьте температуру окружающей среды, проверьте винтовое соединение медной шины питания 237 Overcurrent Protection of Power Output Please check the environment temperature, check copper row screw Защита выходной мощности от перегрузки по току Пожалуйста, проверьте температуру окружающей среды, проверьте винтовое соединение медной шины питания 238 Overcurrent Protection of Power Output Please check the environment temperature, check copper row screw Защита выходной мощности от перегрузки по току Пожалуйста, проверьте температуру окружающей среды, проверьте винтовое соединение медной шины питания 239 Overvoltage Protection of Power Output Inspection of power supply in power grid Защита выходной мощности от перенапряжения Проверка электроснабжения в электросети 240 Low Voltage Protection for Power Output Inspection of power supply in power grid Защита выходной мощности от низкого напряжения Проверка электроснабжения в электросети 241 Power output current imbalance Replace the power Дисбаланс выходного тока Замените питание 243 Over-temperature Protection for Power Input Please check the environment temperature Перегрев. Защита вводной мощности Пожалуйста, проверьте температуру окружающей среды 244 Over-temperature Protection for Power Input Please check the environment temperature Перегрев. Защита вводной мощности Пожалуйста, проверьте температуру окружающей среды 245 Over-temperature Protection for Power Input Please check the environment temperature Перегрев. Защита вводной мощности Пожалуйста, проверьте температуру окружающей среды 246 Overcurrent Protection for Power Input Please check the environment temperature Защита от перегрузки по току вводной мощности Пожалуйста, проверьте температуру окружающей среды 247 Overcurrent Protection for Power Input Please check the environment temperature Защита от перегрузки по току вводной мощности Пожалуйста, проверьте температуру окружающей среды 248 Overvoltage Protection for Power Input Inspection of input voltage in power grid Защита от перенапряжения для вводной мощности Проверьте входное напряжение в электросети 249 Overvoltage Protection for Power Input
Inspection of input voltage in power grid
Защита от перенапряжения для вводной мощности Проверьте входное напряжение в электросети 250 Undervoltage Protection for Power Input Inspection of input voltage in power grid Защита от пониженного напряжения для вводной мощности Проверьте входное напряжение в электросети 251 Undervoltage Protection for Power Input Inspection of input voltage in power grid Защита от пониженного напряжения для потребляемой мощности Проверьте входное напряжение в электросети 253 Power Fan Error Replace the PSU Ошибка вентилятора питания Замените блок питания или вентилятор замените на аналогичный 254 Power Fan Error Replace the PSU Ошибка вентилятора питания Замените блок питания или вентилятор замените на аналогичный 255 Protection of over power output Please check the environment temperature Защита выходной мощности от перегрузки Пожалуйста, проверьте температуру окружающей среды 256 Protection of over power output Please check the environment temperature Защита выходной мощности от перегрузки Пожалуйста, проверьте температуру окружающей среды 257 Input over current protection of power supply primary side Try to power off and restart, no effect to replace the power supply Защита от перегрузки по току на входе первичной стороны источника питания Попробуйте выключить питание и перезапустить или замените источник питания 263 Power communication warning Check whether the screws of the control board are locked Предупреждение об отключении питания Проверьте, зафиксированы ли винты платы управления 264 Power communication error Check whether the screws of the control board are locked Ошибка связи с питанием Проверьте, зафиксированы ли винты платы управления 267 Power watchdog protection Contact the technician in time Защита от отключения питания Вовремя обратитесь к специалисту 268 Power output over-current protection Check the ambient temperature, check the copper bar screw Защита от перегрузки по току на выходной мощности Пожалуйста, проверьте температуру окружающей среды, проверьте винтовое соединение медной шины питания 269 Power input over-current protection Improve power supply conditions and input voltage Защита от перегрузки по току на входе питания Улучшите условия питания и входное напряжение 270 Power input over-voltage protection Inspection of input voltage in power grid Защита от перенапряжения на входе питания Проверка входного напряжения в электросети 271 Power input under-voltage protection Inspection of input voltage in power grid Защита от пониженного напряжения на входе питания Проверка входного напряжения в электросети 272 Warning of excessive power output of power supply Please check the environment temperature Предупреждение о чрезмерной выходной мощности источника питания Пожалуйста, проверьте температуру окружающей среды 273 Power input power too high warning Please check the environment temperature Потребляемая мощность слишком высокая предупреждение Пожалуйста, проверьте температуру окружающей среды 274 Power fan warning Check if the power fan is blocked and may need to be replaced Предупреждение о включении вентилятора Проверьте, не заблокирован ли вентилятор питания и не нуждается ли он в замене или очистке 275 Power over temperature warning Please check the environment temperature Предупреждение о превышении температуры питания Пожалуйста, проверьте температуру окружающей среды 300 SM0 temperature sensor detection error Check the connection of the hashboard Ошибка обнаружения датчика температуры SM0 Проверьте подключение хэш-платы 301 SM1 temperature sensor detection error Check the connection of the hashboard Ошибка обнаружения датчика температуры SM1 Проверьте подключение хэш-платы 302 SM2 temperature sensor detection error Check the connection of the hashboard Ошибка обнаружения датчика температуры SM2 Проверьте подключение хэш-платы 320 SM0 temperature reading error Check whether the control board screw is locked properly, check the connection board and the arrangement contact Ошибка считывания температуры SM0 Проверьте, правильно ли зафиксирован винты платы управления, проверьте соединительную плату и установочный контакт 321 SM1 temperature reading error Check whether the control board screw is locked properly, check the connection board and the arrangement contact Ошибка считывания температуры SM1 Проверьте, правильно ли зафиксирован винт платы управления, проверьте соединительную плату и установочный контакт 322 SM2 temperature reading error Check whether the control board screw is locked properly, check the connection board and the arrangement contact Ошибка считывания температуры SM2 Проверьте, правильно ли зафиксирован винт платы управления, проверьте соединительную плату и установочный контакт 329 Control board temperature sensor communication error Replace the power supply Ошибка связи с датчиком температуры контрольной платы Замените блок питания 350 SM0 temperature protecting Please check the environment temperature Защита от температуры SM0 Пожалуйста, проверьте температуру окружающей среды 351 SM1 temperature protecting Please check the environment temperature Защита от перегрева SM1 Пожалуйста, проверьте температуру окружающей среды 352 SM2 temperature protecting Please check the environment temperature Защита от температуры SM2 Пожалуйста, проверьте температуру окружающей среды 410 SM0 detect eeprom error Check adapter board and wiring contact SM0 обнаружение ошибки eeprom ( памяти) Проверьте плату адаптера и контакты проводки 411 SM1 detect eeprom error Check adapter board and wiring contact SM1 обнаруживает ошибку eeprom Проверьте плату адаптера и контакты проводки 412 SM2 detect eeprom error Check adapter board and wiring contact SM2 обнаруживает ошибку eeprom Проверьте плату адаптера и контакты проводки 420 SM0 parser eeprom error Contact the technician in time Ошибка eeprom анализатора SM0 Вовремя обратитесь к специалисту 421 SM1 parser eeprom error Contact the technician in time Ошибка eeprom анализатора SM1 Вовремя обратитесь к специалисту 422 SM2 parser eeprom error Contact the technician in time Ошибка eeprom анализатора SM2 Вовремя обратитесь к специалисту 430 SM0 chip bin type error Contact the technician in time Ошибка бинарного кода для микросхем SM0 Вовремя обратитесь к специалисту 431 SM1 chip bin type error Contact the technician in time Ошибка бинарного кода для микросхем SM1 Вовремя обратитесь к специалисту 432 SM2 chip bin type error Contact the technician in time Ошибка бинарного кода для микросхем SM2 Вовремя обратитесь к специалисту 440 SM0 eeprom chip num X error Contact the technician in time Ошибка SM0 ошибка внутренней памяти чипа X Вовремя обратитесь к специалисту 441 SM1 eeprom chip num X error Contact the technician in time Ошибка SM1 ошибка внутренней памяти чипа X Вовремя обратитесь к специалисту 442 SM2 eeprom chip num X error Contact the technician in time Ошибка SM2 ошибка внутренней памяти чипа X Вовремя обратитесь к специалисту 510 SM0 miner type error The version and type of hashboard are inconsistent, replace the correct hashboard Ошибка типа майнера SM0 Версия и тип хэш-плату несовместимы, замените на правильную хэш-плату 511 SM1 miner type error The version and type of hashboard are inconsistent, replace the correct hashboard Ошибка типа майнера SM1 Версия и тип хэш-плату несовместимы, замените на правильную хэш-плату 512 SM2 miner type error The version and type of hashboard are inconsistent, replace the correct hashboard Ошибка типа майнера SM2 Версия и тип хэш-плату несовместимы, замените на правильную хэш-плату 530 SM0 not found Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded SM0 не найден Проверьте подключение и расположение платы адаптера или замените плату управления, проверьте подключение разъема платы адаптера. 531 SM1 not found Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded SM1 не найден Проверьте подключение и расположение платы адаптера или замените плату управления, проверьте подключение разъема платы адаптера.. 532 SM2 not found Check the connection and arrangement of the adapter board, or replace the contro board, check whether the hash board connector is empty welded SM2 не найден Проверьте подключение и расположение платы адаптера или замените плату управления, проверьте подключение разъема платы адаптера. 540 SM0 reading chip id error Check adapter board and wiring contact, Clean the dust on the hashboard Ошибка считывания идентификатора микросхемы SM0 Проверьте плату адаптера и контакты проводки, Очистите от пыли хэш-плату 541 SM1 reading chip id error Check adapter board and wiring contact, Clean the dust on the hashboard Ошибка считывания идентификатора микросхемы SM1 Проверьте плату адаптера и контакты проводки, Очистите от пыли хэш-плату 542 SM2 reading chip id error Check adapter board and wiring contact, Clean the dust on the hashboard Ошибка считывания идентификатора микросхемы SM2 Проверьте плату адаптера и контакты проводки, Очистите от пыли хэш-плату 550 SM0 have bad chips Replacement of bad chips У SM0 плохие чипы Замена плохих чипов 551 SM1 have bad chips Replacement of bad chips У SM1 плохие чипы Замена плохих чипов 552 SM2 have bad chips Replacement of bad chips У SM2 плохие чипы Замена плохих чипов 560 SM0 loss balance Plug in the adapter plate, and then screw in the power connection hashboard again Баланс потерь SM0 Вставьте в розетку переходную пластину, а затем снова ввинтите разъем подключения питания 561 SM1 loss balance Plug in the adapter plate, and then screw in the power connection hashboard again Баланс потерь SM1 Вставьте в розетку переходную пластину, а затем снова ввинтите разъем подключения питания 562 SM2 loss balance Plug in the adapter plate, and then screw in the power connection hashboard again Баланс потерь SM2 Вставьте в розетку переходную пластину, а затем снова ввинтите разъем подключения питания 600 Environment temperature is high Please check the environment temperature Температура окружающей среды высокая Пожалуйста, проверьте температуру окружающей среды 610 If the ambient temperature is too high in high performance mode, return to normal mode Check the ambient temperature, high performance mode needs to be controlled below 30 ℃ Если температура окружающей среды слишком высока в режиме высокой производительности, вернитесь в нормальный режим Проверьте температуру окружающей среды, необходимо контролировать режим высокой производительности ниже 30 ℃ 710 Control board rebooted as exception Updating the latest firmware.Check whether the control board screw is locked properly Плата управления перезагружена как исключение Обновление последней версии прошивки. Проверьте, правильно ли зафиксирован винт платы управления 800 cgminer checksum error Re-upgrade firmware ошибка контрольной суммы cgminer Повторное обновление встроенного ПО 801 system-monitor checksum error Re-upgrade firmware ошибка контрольной суммы системного монитора Повторное обновление встроенного ПО 802 remote-daemon checksum error Re-upgrade firmware ошибка контрольной суммы удаленных служебных задач Повторное обновление встроенного ПО 2010 All pools are disable Please check the network or pools configure Все пулы отключены Пожалуйста, проверьте настройки сети или пулов 2020 Pool0 connect failed Please check the network or pools configure Ошибка подключения пулом0 Пожалуйста, проверьте настройки сети или пулов 2021 Pool1 connect failed Please check the network or pools configure Сбой соединения с пулом1 Пожалуйста, проверьте настройки сети или пулов 2022 Pool2 connect failed Please check the network or pools configure Сбой соединения с пулом2 Пожалуйста, проверьте настройки сети или пулов 2030 High rejection rate of pool Please check the network or pools configure.Setting of mining currency Высокий процент отбраковки пула Пожалуйста, проверьте настройки сети или пулов. Настройка валюты майнинга 2040 The pool does not support the asicboost mode Check pool configuration Пул не поддерживает режим asicboost Проверьте конфигурацию пула 5110 SM0 Frequency Up Timeout reboot Время ожидания увеличения частоты SM0 перезагрузка 5111 SM1 Frequency Up Timeout reboot Тайм-аут увеличения частоты SM1 перезагрузка 5112 SM2 Frequency Up Timeout reboot Время ожидания увеличения частоты SM2 перезагрузка 8410 Software version error (M2x miner with M3x firmware, or M3x with M2x firmware). Upgrade to the correct firmware version Ошибка версии программного обеспечения ((M2 x miner с прошивкой M3x или M3x с прошивкой 2x). Обновите прошивку до правильной версии PSU
Error code
Reason processing method Причина Способ устранения 0x0001 Input undervoltage Check the power supply Входное напряжение низкое Проверьте источник питания 0x0002 Temperature sampling over temperature protection of power radiator Power on again after 10 minutes of power failure. If it occurs again, replace the power supply Измерение температуры защита от перегрева силового радиатора Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания 0x0004 Temperature sampling over temperature protection of power radiator Power on again after 10 minutes of power failure. If it occurs again, replace the power supply Измерение температуры защита от перегрева силового радиатора Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания 0x0008 Over temperature protection of environmental temperature sampling in power supply Power on again after 10 minutes of power failure. If it occurs again, replace the power supply Защита от перегрева при отборе проб температуры окружающей среды в источнике питания Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания 0x0010 Primary side over current Power on again after 10 minutes of power failure. If it occurs again, replace the power supply Перегрузка по току на первичной стороне Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания 0x0020 Output undervoltage Check the power supply Пониженное выходное напряжение Проверьте источник питания 0x0040 Output over current (continuous load 320A for more than 2S) Tighten the copper bar screw again Перегрузка по току на выходе (непрерывная нагрузка 320A более 2 секунд) Снова затяните винт на медной шине 0x0080 Primary side over current Power on again after 10 minutes of power failure. If it occurs again, replace the power supply Перегрузка по току на первичной стороне Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания 0x0100 Single circuit overcurrent(protection point 120a) Check the PSU Перегрузка по току в одной цепи (точка защиты 120а) Проверьте блок питания 0x0200 Single circuit overcurrent(protection point 120a) Check the PSU Перегрузка по току в одной цепи (точка защиты 120а) Проверьте блок питания 0x0400 Single circuit overcurrent(protection point 120a) Check the PSU Перегрузка по току в одной цепи (точка защиты 120а) Проверьте блок питания 0x0800 Fan failure Replace the PSU Неисправность вентилятора Замените блок питания 0x1000 Output over current (continuous load of 310A for more than 5min) Check the PSU Перегрузка по току на выходе (непрерывная нагрузка 310 А более 5 мин) Проверьте блок питания 0x2000 Output over current (continuous load 295A for more than 10min) Check the PSU Перегрузка по току на выходе (непрерывная нагрузка 295 А более 10 мин) Проверьте блок питания
Error code
Reason
Processing method
Причина
Способ устранения
110
Fanin detect speed error
Check whether the fan connection is normal, or replace the power supply, or replace the
fan
Ошибка обнаружения скорости вращения вентилятора на входе
Проверьте, правильно ли подключен вентилятор, исправен ли он. Замените источник питания, или замените вентилятор
111
Fanout detect speed error
Check whether the fan connection is normal, or replace the power supply, or replace the
fan
Ошибка обнаружения скорости вращения вентилятора на выходе
Проверьте, правильно ли подключен вентилятор, исправен ли он. Замените источник питания, или замените вентилятор
130
Fanin speed error
Check whether the fan connection is normal, or replace the power supply, or replace the
fan
Ошибка скорости вращения вентилятора на входе
Проверьте, правильно ли подключен вентилятор, исправен ли он. Замените источник питания, или замените вентилятор
131
Fanout speed error
Check whether the fan connection is normal, or replace the power supply, or replace the
fan
Ошибка скорости вращения вентилятора на выходе
Проверьте, правильно ли подключен вентилятор, исправен ли он. Замените источник питания, или замените вентилятор
140
Fan speed is too high
Please check the environment temperature
Слишком высокая скорость вращения вентилятора
Пожалуйста, проверьте температуру окружающей среды или проверьте запыленность хэшплат
200
Power probing error, no power found
Detecting power output wiring, updating the latest firmware, or replacing power supply
Ошибка измерения мощности, питание не найдено
Проверьте силовую проводку, обновите до последней версии встроенное программное обеспечение или замена источника питания
201
Power supply and configuration file mismatch
Replace the correct PSU
Несоответствие источника питания и конфигурационного файла
Замените блок питания на оригинальный
203
Power protecting
Please check the environment temperature
Защита по питанию
Пожалуйста, проверьте температуру окружающей среды
204
Power current protecting
Please check the environment temperature
Защита от тока питания
Пожалуйста, проверьте температуру окружающей среды
205
Power current error
Inspection of power supply in power grid
Ошибка тока питания
Проверка электроснабжения в электросети
206
Power input voltage is low
Improve power supply conditions and input voltage
Входное напряжение питания низкое
Проверьте напряжение под нагрузкой. Улучшите условия подключения майнера
207
Power input current protecting
Improve power supply conditions and input voltage
Защита от входного тока питания
Улучшите условия питания и входное напряжение
210
Power error status
Check power failure code
Состояние ошибки питания
Проверьте код сбоя питания
213
Power input voltage and current do not match the power
Replace the PSU
Входное напряжение и ток питания не соответствуют мощности
Проверьте напряжение под нагрузкой. Улучшите условия подключения майнера Замените блок питания
233
Power output over temperature protection
Please check the environment temperature
Защита выходной мощности от перегрева
Пожалуйста, проверьте температуру окружающей среды
234
Power output over temperature protection
Please check the environment temperature
Защита выходной мощности от перегрева
Пожалуйста, проверьте температуру окружающей среды
235
Power output over temperature protection
Please check the environment temperature
Защита выходной мощности от перегрева
Пожалуйста, проверьте температуру окружающей среды
236
Overcurrent Protection of Power Output
Please check the environment temperature, check copper row screw
Защита выходной мощности от перегрузки по току
Пожалуйста, проверьте температуру окружающей среды, проверьте винтовое соединение медной шины питания
237
Overcurrent Protection of Power Output
Please check the environment temperature, check copper row screw
Защита выходной мощности от перегрузки по току
Пожалуйста, проверьте температуру окружающей среды, проверьте винтовое соединение медной шины питания
238
Overcurrent Protection of Power Output
Please check the environment temperature, check copper row screw
Защита выходной мощности от перегрузки по току
Пожалуйста, проверьте температуру окружающей среды, проверьте винтовое соединение медной шины питания
239
Overvoltage Protection of Power Output
Inspection of power supply in power grid
Защита выходной мощности от перенапряжения
Проверка электроснабжения в электросети
240
Low Voltage Protection for Power Output
Inspection of power supply in power grid
Защита выходной мощности от низкого напряжения
Проверка электроснабжения в электросети
241
Power output current imbalance
Replace the power
Дисбаланс выходного тока
Замените питание
243
Over-temperature Protection for Power Input
Please check the environment temperature
Перегрев. Защита вводной мощности
Пожалуйста, проверьте температуру окружающей среды
244
Over-temperature Protection for Power Input
Please check the environment temperature
Перегрев. Защита вводной мощности
Пожалуйста, проверьте температуру окружающей среды
245
Over-temperature Protection for Power Input
Please check the environment temperature
Перегрев. Защита вводной мощности
Пожалуйста, проверьте температуру окружающей среды
246
Overcurrent Protection for Power Input
Please check the environment temperature
Защита от перегрузки по току вводной мощности
Пожалуйста, проверьте температуру окружающей среды
247
Overcurrent Protection for Power Input
Please check the environment temperature
Защита от перегрузки по току вводной мощности
Пожалуйста, проверьте температуру окружающей среды
248
Overvoltage Protection for Power Input
Inspection of input voltage in power grid
Защита от перенапряжения для вводной мощности
Проверьте входное напряжение в электросети
249
Overvoltage Protection for Power Input
Inspection of input voltage in power grid
Защита от перенапряжения для вводной мощности
Проверьте входное напряжение в электросети
250
Undervoltage Protection for Power Input
Inspection of input voltage in power grid
Защита от пониженного напряжения для вводной мощности
Проверьте входное напряжение в электросети
251
Undervoltage Protection for Power Input
Inspection of input voltage in power grid
Защита от пониженного напряжения для потребляемой мощности
Проверьте входное напряжение в электросети
253
Power Fan Error
Replace the PSU
Ошибка вентилятора питания
Замените блок питания или вентилятор замените на аналогичный
254
Power Fan Error
Replace the PSU
Ошибка вентилятора питания
Замените блок питания или вентилятор замените на аналогичный
255
Protection of over power output
Please check the environment temperature
Защита выходной мощности от перегрузки
Пожалуйста, проверьте температуру окружающей среды
256
Protection of over power output
Please check the environment temperature
Защита выходной мощности от перегрузки
Пожалуйста, проверьте температуру окружающей среды
257
Input over current protection of power supply primary side
Try to power off and restart, no effect to replace the power supply
Защита от перегрузки по току на входе первичной стороны источника питания
Попробуйте выключить питание и перезапустить или замените источник питания
263
Power communication warning
Check whether the screws of the control board are locked
Предупреждение об отключении питания
Проверьте, зафиксированы ли винты платы управления
264
Power communication error
Check whether the screws of the control board are locked
Ошибка связи с питанием
Проверьте, зафиксированы ли винты платы управления
267
Power watchdog protection
Contact the technician in time
Защита от отключения питания
Вовремя обратитесь к специалисту
268
Power output over-current protection
Check the ambient temperature, check the copper bar screw
Защита от перегрузки по току на выходной мощности
Пожалуйста, проверьте температуру окружающей среды, проверьте винтовое соединение медной шины питания
269
Power input over-current protection
Improve power supply conditions and input voltage
Защита от перегрузки по току на входе питания
Улучшите условия питания и входное напряжение
270
Power input over-voltage protection
Inspection of input voltage in power grid
Защита от перенапряжения на входе питания
Проверка входного напряжения в электросети
271
Power input under-voltage protection
Inspection of input voltage in power grid
Защита от пониженного напряжения на входе питания
Проверка входного напряжения в электросети
272
Warning of excessive power output of power supply
Please check the environment temperature
Предупреждение о чрезмерной выходной мощности источника питания
Пожалуйста, проверьте температуру окружающей среды
273
Power input power too high warning
Please check the environment temperature
Потребляемая мощность слишком высокая предупреждение
Пожалуйста, проверьте температуру окружающей среды
274
Power fan warning
Check if the power fan is blocked and may need to be replaced
Предупреждение о включении вентилятора
Проверьте, не заблокирован ли вентилятор питания и не нуждается ли он в замене или очистке
275
Power over temperature warning
Please check the environment temperature
Предупреждение о превышении температуры питания
Пожалуйста, проверьте температуру окружающей среды
300
SM0 temperature sensor detection error
Check the connection of the hashboard
Ошибка обнаружения датчика температуры SM0
Проверьте подключение хэш-платы
301
SM1 temperature sensor detection error
Check the connection of the hashboard
Ошибка обнаружения датчика температуры SM1
Проверьте подключение хэш-платы
302
SM2 temperature sensor detection error
Check the connection of the hashboard
Ошибка обнаружения датчика температуры SM2
Проверьте подключение хэш-платы
320
SM0 temperature reading error
Check whether the control board screw is locked properly, check the connection board and the arrangement contact
Ошибка считывания температуры SM0
Проверьте, правильно ли зафиксирован винты платы управления, проверьте соединительную плату и установочный контакт
321
SM1 temperature reading error
Check whether the control board screw is locked properly, check the connection board and the arrangement contact
Ошибка считывания температуры SM1
Проверьте, правильно ли зафиксирован винт платы управления, проверьте соединительную плату и установочный контакт
322
SM2 temperature reading error
Check whether the control board screw is locked properly, check the connection board and the arrangement contact
Ошибка считывания температуры SM2
Проверьте, правильно ли зафиксирован винт платы управления, проверьте соединительную плату и установочный контакт
329
Control board temperature sensor communication error
Replace the power supply
Ошибка связи с датчиком температуры контрольной платы
Замените блок питания
350
SM0 temperature protecting
Please check the environment temperature
Защита от температуры SM0
Пожалуйста, проверьте температуру окружающей среды
351
SM1 temperature protecting
Please check the environment temperature
Защита от перегрева SM1
Пожалуйста, проверьте температуру окружающей среды
352
SM2 temperature protecting
Please check the environment temperature
Защита от температуры SM2
Пожалуйста, проверьте температуру окружающей среды
410
SM0 detect eeprom error
Check adapter board and wiring contact
SM0 обнаружение ошибки eeprom ( памяти)
Проверьте плату адаптера и контакты проводки
411
SM1 detect eeprom error
Check adapter board and wiring contact
SM1 обнаруживает ошибку eeprom
Проверьте плату адаптера и контакты проводки
412
SM2 detect eeprom error
Check adapter board and wiring contact
SM2 обнаруживает ошибку eeprom
Проверьте плату адаптера и контакты проводки
420
SM0 parser eeprom error
Contact the technician in time
Ошибка eeprom анализатора SM0
Вовремя обратитесь к специалисту
421
SM1 parser eeprom error
Contact the technician in time
Ошибка eeprom анализатора SM1
Вовремя обратитесь к специалисту
422
SM2 parser eeprom error
Contact the technician in time
Ошибка eeprom анализатора SM2
Вовремя обратитесь к специалисту
430
SM0 chip bin type error
Contact the technician in time
Ошибка бинарного кода для микросхем SM0
Вовремя обратитесь к специалисту
431
SM1 chip bin type error
Contact the technician in time
Ошибка бинарного кода для микросхем SM1
Вовремя обратитесь к специалисту
432
SM2 chip bin type error
Contact the technician in time
Ошибка бинарного кода для микросхем SM2
Вовремя обратитесь к специалисту
440
SM0 eeprom chip num X error
Contact the technician in time
Ошибка SM0 ошибка внутренней памяти чипа X
Вовремя обратитесь к специалисту
441
SM1 eeprom chip num X error
Contact the technician in time
Ошибка SM1 ошибка внутренней памяти чипа X
Вовремя обратитесь к специалисту
442
SM2 eeprom chip num X error
Contact the technician in time
Ошибка SM2 ошибка внутренней памяти чипа X
Вовремя обратитесь к специалисту
510
SM0 miner type error
The version and type of hashboard are inconsistent, replace the correct hashboard
Ошибка типа майнера SM0
Версия и тип хэш-плату несовместимы, замените на правильную хэш-плату
511
SM1 miner type error
The version and type of hashboard are inconsistent, replace the correct hashboard
Ошибка типа майнера SM1
Версия и тип хэш-плату несовместимы, замените на правильную хэш-плату
512
SM2 miner type error
The version and type of hashboard are inconsistent, replace the correct hashboard
Ошибка типа майнера SM2
Версия и тип хэш-плату несовместимы, замените на правильную хэш-плату
530
SM0 not found
Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded
SM0 не найден
Проверьте подключение и расположение платы адаптера или замените плату управления, проверьте подключение разъема платы адаптера.
531
SM1 not found
Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded
SM1 не найден
Проверьте подключение и расположение платы адаптера или замените плату управления, проверьте подключение разъема платы адаптера..
532
SM2 not found
Check the connection and arrangement of the adapter board, or replace the contro board, check whether the hash board connector is empty welded
SM2 не найден
Проверьте подключение и расположение платы адаптера или замените плату управления, проверьте подключение разъема платы адаптера.
540
SM0 reading chip id error
Check adapter board and wiring contact, Clean the dust on the hashboard
Ошибка считывания идентификатора микросхемы SM0
Проверьте плату адаптера и контакты проводки, Очистите от пыли хэш-плату
541
SM1 reading chip id error
Check adapter board and wiring contact, Clean the dust on the hashboard
Ошибка считывания идентификатора микросхемы SM1
Проверьте плату адаптера и контакты проводки, Очистите от пыли хэш-плату
542
SM2 reading chip id error
Check adapter board and wiring contact, Clean the dust on the hashboard
Ошибка считывания идентификатора микросхемы SM2
Проверьте плату адаптера и контакты проводки, Очистите от пыли хэш-плату
550
SM0 have bad chips
Replacement of bad chips
У SM0 плохие чипы
Замена плохих чипов
551
SM1 have bad chips
Replacement of bad chips
У SM1 плохие чипы
Замена плохих чипов
552
SM2 have bad chips
Replacement of bad chips
У SM2 плохие чипы
Замена плохих чипов
560
SM0 loss balance
Plug in the adapter plate, and then screw in the power connection hashboard again
Баланс потерь SM0
Вставьте в розетку переходную пластину, а затем снова ввинтите разъем подключения питания
561
SM1 loss balance
Plug in the adapter plate, and then screw in the power connection hashboard again
Баланс потерь SM1
Вставьте в розетку переходную пластину, а затем снова ввинтите разъем подключения питания
562
SM2 loss balance
Plug in the adapter plate, and then screw in the power connection hashboard again
Баланс потерь SM2
Вставьте в розетку переходную пластину, а затем снова ввинтите разъем подключения питания
600
Environment temperature is high
Please check the environment temperature
Температура окружающей среды высокая
Пожалуйста, проверьте температуру окружающей среды
610
If the ambient temperature is too high in high performance mode, return to normal mode
Check the ambient temperature, high performance mode needs to be controlled below 30 ℃
Если температура окружающей среды слишком высока в режиме высокой производительности, вернитесь в нормальный режим
Проверьте температуру окружающей среды, необходимо контролировать режим высокой производительности ниже 30 ℃
710
Control board rebooted as exception
Updating the latest firmware.Check whether the control board screw is locked properly
Плата управления перезагружена как исключение
Обновление последней версии прошивки. Проверьте, правильно ли зафиксирован винт платы управления
800
cgminer checksum error
Re-upgrade firmware
ошибка контрольной суммы cgminer
Повторное обновление встроенного ПО
801
system-monitor checksum error
Re-upgrade firmware
ошибка контрольной суммы системного монитора
Повторное обновление встроенного ПО
802
remote-daemon checksum error
Re-upgrade firmware
ошибка контрольной суммы удаленных служебных задач
Повторное обновление встроенного ПО
2010
All pools are disable
Please check the network or pools configure
Все пулы отключены
Пожалуйста, проверьте настройки сети или пулов
2020
Pool0 connect failed
Please check the network or pools configure
Ошибка подключения пулом0
Пожалуйста, проверьте настройки сети или пулов
2021
Pool1 connect failed
Please check the network or pools configure
Сбой соединения с пулом1
Пожалуйста, проверьте настройки сети или пулов
2022
Pool2 connect failed
Please check the network or pools configure
Сбой соединения с пулом2
Пожалуйста, проверьте настройки сети или пулов
2030
High rejection rate of pool
Please check the network or pools configure.Setting of mining currency
Высокий процент отбраковки пула
Пожалуйста, проверьте настройки сети или пулов. Настройка валюты майнинга
2040
The pool does not support the asicboost mode
Check pool configuration
Пул не поддерживает режим asicboost
Проверьте конфигурацию пула
5110
SM0 Frequency Up Timeout
reboot
Время ожидания увеличения частоты SM0
перезагрузка
5111
SM1 Frequency Up Timeout
reboot
Тайм-аут увеличения частоты SM1
перезагрузка
5112
SM2 Frequency Up Timeout
reboot
Время ожидания увеличения частоты SM2
перезагрузка
8410
Software version error (M2x miner with M3x firmware, or M3x with M2x firmware).
Upgrade to the correct firmware version
Ошибка версии программного обеспечения ((M2 x miner с прошивкой M3x или M3x с прошивкой 2x).
Обновите прошивку до правильной версии
PSU
Error code
Reason
processing method
Причина
Способ устранения
0x0001
Input undervoltage
Check the power supply
Входное напряжение низкое
Проверьте источник питания
0x0002
Temperature sampling over temperature protection of power radiator
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Измерение температуры защита от перегрева силового радиатора
Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания
0x0004
Temperature sampling over temperature protection of power radiator
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Измерение температуры защита от перегрева силового радиатора
Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания
0x0008
Over temperature protection of environmental temperature sampling in power supply
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Защита от перегрева при отборе проб температуры окружающей среды в источнике питания
Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания
0x0010
Primary side over current
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Перегрузка по току на первичной стороне
Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания
0x0020
Output undervoltage
Check the power supply
Пониженное выходное напряжение
Проверьте источник питания
0x0040
Output over current (continuous load 320A for more than 2S)
Tighten the copper bar screw again
Перегрузка по току на выходе (непрерывная нагрузка 320A более 2 секунд)
Снова затяните винт на медной шине
0x0080
Primary side over current
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Перегрузка по току на первичной стороне
Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания
0x0100
Single circuit overcurrent(protection point 120a)
Check the PSU
Перегрузка по току в одной цепи (точка защиты 120а)
Проверьте блок питания
0x0200
Single circuit overcurrent(protection point 120a)
Check the PSU
Перегрузка по току в одной цепи (точка защиты 120а)
Проверьте блок питания
0x0400
Single circuit overcurrent(protection point 120a)
Check the PSU
Перегрузка по току в одной цепи (точка защиты 120а)
Проверьте блок питания
0x0800
Fan failure
Replace the PSU
Неисправность вентилятора
Замените блок питания
0x1000
Output over current (continuous load of 310A for more than 5min)
Check the PSU
Перегрузка по току на выходе (непрерывная нагрузка 310 А более 5 мин)
Проверьте блок питания
0x2000
Output over current (continuous load 295A for more than 10min)
Check the PSU
Перегрузка по току на выходе (непрерывная нагрузка 295 А более 10 мин)
Проверьте блок питания
Коды ошибок асик майнера WhatsMiner
0 ErrSucc ОК ОК — обычный
21 ErrNotPlugged 1 или более хеш-плат не обнаружены Сигнал Hashboard PLUG не обнаружен Номер обнаруженной платы питания, если их более одной, разделенные пробелами 1. Проверьте правильность подключения кабеля SPI (по сравнению с обычной машиной) и снова подключите кабель. 2. Замените плату управления. 3. Замените проблемную доску хешрейта (переделайте доску головоломки).
22 ErrPsuI2cFail Аномальная связь по управлению питанием Неправильная связь I2C источника питания — 1. Заменить блок питания. 2. Замените плату управления.
23 ErrEncoreAllFail Все хэш-платы не могут быть включены SPI недоступен для всех плат хешрейта — 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Отремонтируйте всю машину.
24 ErrEncoreFail Некоторые платы не включаются SPI недоступен на некоторых хэш-досках Номер хэшборда, для которого произошел сбой связи по SPI, если их несколько, разделенных пробелами 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Замените проблемную хеш-доску (переделайте доску-головоломку).
25 ErrSetPllFail Не удалось поднять частоту хэш-платы Не удалось поднять частоту хэш-платы Номер хэшборда: частота ошибок 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Замените проблемную хеш-доску (переделайте доску-головоломку).
26 ErrSetVolFail Не удалось установить напряжение Не удалось установить напряжение Номер хэшборда: 1/2 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Заменить проблемную хеш-доску (присоединиться)
27 ErrBistFail Тест чипа BIST не пройден Тест чипа BIST не пройден Номер хэшборда: 1/2 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить проблемную хеш-доску (присоединиться к плате)
28 ErrSpiFail Ненормальная связь платы хешрейта не может быть автоматически восстановлена ??во время работы Ненормальное соединение SPI платы хешрейта не может быть автоматически восстановлено во время работы Номер хэшборда 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Замените проблемную хеш-доску (переделайте доску-головоломку)
29 ErrI2cFail Ненормальная связь по питанию во время работы не может быть восстановлена ??автоматически Связь I2C с ненормальным источником питания не может быть автоматически восстановлена ??во время работы — 1. Заменить блок питания. 2. Замените плату управления.
30 ErrNetwork Подключение к майнинговому пулу прервано Подключение к майнинговому пулу прервано — Если эта проблема возникает на большом количестве или на всех майнинговых машинах с одним и тем же коммутатором: 1. Проверьте правильность настроек пула для майнинга. 2. Проверьте конфигурацию сетевой среды (например, конфигурацию DHCP, конфигурацию DNS, порт и т. Д.). Если проблемы возникают только на одной или нескольких машинах для майнинга: 1. Проверьте правильность настроек пула для майнинга. 2. Проверить подключения к сетевому порту майнера. 3. Замените сетевой кабель на работающую майнинговую машину. 4. Замените плату управления.
31 ErrBadChip Повреждение отдельных микросхем, что приводит к искусственно завышенной вычислительной мощности Повреждение отдельных микросхем, что приводит к искусственно завышенной вычислительной мощности Номер поврежденной микросхемы: номер хеш-платы, если их более одной, разделенные пробелами В ремонт
32 ErrOverheat Hashboard перегрелся Hashboard перегрелся Номер хэшборда 1. Проверьте, вращаются ли передний и задний вентиляторы, если они не вращаются, сначала замените вентиляторы, а затем замените плату управления / блок питания. 2. Убедитесь, что направление ветра спереди и сзади согласовано, согласуется ли оно с другими машинами, если нет, измените направление вентилятора. 3. Если температура воздуха на входе горной машины превышает 40 градусов, необходимо улучшить температурную среду в шахте. 4. Если определенная плата хешрейта часто перегревается, вы можете заменить проблемную плату хешрейта (переделайте головоломку).
33 ErrInvTemp Невозможно прочитать температуру чипа Невозможно прочитать температуру чипа Номер хэшборда 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Замените проблемную хеш-доску (переделайте доску-головоломку).
34 ErrMisPlugged Неправильное подключение кабеля связи платы управления Ненормальное подключение кабеля SPI платы управления Номер хэшборда 1. Проверьте, совместим ли метод (последовательность) подключения кабеля SPI хэш-платы с другими машинами той же модели. 2. Замените плату управления.
35 ErrPsuFail Аномальный источник питания Аномальный источник питания 1. Обратите внимание на то, что если нет явного отклонения от нормы вычислительной мощности всей машины (не отключается плата), то перезагрузить 2. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 3. Заменить блок питания.
36 ErrInvCorenum Некоторые чипы не работают должным образом Количество хороших фишек ненормальное Номер хэшборда: номер чипа 1. Обратите внимание на то, что если нет явного отклонения от нормы вычислительной мощности всей машины (не отключается плата), то перезагрузить 2. Перезапустите майнер, чтобы увидеть, появляется ли по-прежнему та же ошибка. 3. Замените проблемную хеш-плату.
37 ErrInvVidtype Тип платы управления / версия прошивки / количество микросхем не совпадает Тип платы управления / версия прошивки / количество микросхем не совпадает vidtype, minertype, subtype, chipnum После накопления нескольких единиц (> 10) обратитесь в ремонт.
38 ErrBadRearChips Наконец, у некоторых чипов низкая вычислительная мощность. Последние несколько уровней чипов имеют низкую вычислительную мощность В ремонт
39 ErrInvTuneParam Аномальные параметры старения Напряжение начальной частоты старения неверно В ремонт
Errcode | Scope of application | Explanation | Troubleshooting steps |
0 | Whole miner | Normal | Normal |
21 | hashboard | one or more hashboards can’t be detected | 1. check and see whether the SPI cables are firmly and correctly connected (compared the connection of cables with working miners), reconnect the SPI cables, don’t change sequence of connection 2. replace control board with other well functional one 3. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
22 | Whole miner | PSU communication is abnormal | 1. replace PSU with other well functional one 2. replace control board with other well functional one |
23 | Whole miner | All hashboards can’t be powered up | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. whole miner should be returned for repair |
24 | hashboard | one or more hashboards can’t be powered up | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
25 | hashboard | frequency increase of hashboards fails | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check and see whether screws on the PSU side and SPI connection are loose 3. replace PSU with other well functional one 4. replace control board with other well functional one 5. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
26 | hashboard | voltage setting fails | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
27 | hashboard | chip BIST test fails | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
28 | hashboard | abnormal communication of hashboard, it can’t be automatically recovered when running | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
29 | Whole miner | abnormal communication of PSU can’t be automatically recovered when running | 1. replace PSU with other well functional one 2. replace control board with other well functional one |
30 | Whole miner | pool disconnect | If the problem occurs in a large number of miners or all of the mines under the same switch: 1. please first check whether pool setting is correct 2. then check network configuration (such as DHCP configuration, DNS configuration, ports, etc.) If the problem occurs in only one or just a small number of miners under the same switch: 1. please first check whether pool setting is correct 2. then check whether network cable is firmly connected 3. replace network cable with other one from other well working miner 4. replace control board with other well functional one |
31 | hashboard | damage of some individual chip causes inflated high hashrate of the miner | no action should be taken |
32 | hashboard | hashboard overheat | 1. check and see whether both fans are spinning, if not, replace fan with other functional one, if still not, then replace control board or PSU 2. check and see whether wind direction of both fans are the same, whether wind direction are the same with other miners, if not, exchange fans 3. meter the inlet temperature of the miner, if above 40 °C, cooling system of the mining farm should be improved 4. if some hashboard is overheated frequently, that hashboard should be replaced (returned for repair) |
33 | hashboard | chip temperature can’t be read | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
34 | cables of control board is connected incorrectly | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check whether hashboard SPI cables are conneted in the same way (sequence) as other miners of same model 3. replace control board with other well functional one |
|
35 | hashboard | PSU voltage is too low | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2.check and see whether screws on the PSU side and SPI connection is loose 3. replace PSU with other well functional one |
36 | hashboard | working or some chips is abnormal | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. reboot the miner to see whether the same error is given 3. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
37 | Whole miner | mismatch of control board version/firmware version/quantity of chips | if there are more than 10 miners with same error, please contact engineers |
38 | hashboard | low hashrate of last few chips | no action should be taken |
39 | hashboard | testing parameter is abnormal | no action should be taken |
40 | hashboard | PSU load is insufficient | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
41 | hashboard | startup voltage of PSU is too low | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check and see whether screws on the PSU side and SPI connection are loose 3. replace PSU with other well functional one 4. replace control board with other well functional one |
42 | hashboard | implementation of plan B fails when hashboard frequency increases | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check and see whether screws on the PSU side and SPI connection are loose 3. replace PSU with other well functional one 4. replace control board with other well functional one 5. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
Attention: 1. The miner should be powered up again to see whether it is back to normal after every step is taken 2. If the problem is not solve after replacement the part, the part should go back to its original unit 3. Error code and brief description of the problem should be attached to the hashboard that is confirmed defective and that will be returned for repair |
Error
code
Reason Processing method
110 Fanin detect speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
fan
111 Fanout detect speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
fan
130 Fanin speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
fan
131 Fanout speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
fan
140 Fan speed is too high Please check the environment temperature
200
Power probing error, no
power found
Detecting power output wiring, updating the
latest firmware, or replacing power supply
201
Power supply and
configuration file
mismatch
Replace the correct PSU
203 Power protecting Please check the environment temperature
204 Power current protecting Please check the environment temperature
205 Power current error Inspection of power supply in power grid
206 Power input voltage is low
Improve power supply conditions and input
voltage
207
Power input current
protecting
Improve power supply conditions and input
voltage
210 Power error status Check power failure code
213
Power input voltage and
current do not match the
power
Replace the PSU
233
Power output over
temperature protection
Please check the environment temperature
234
Power output over
temperature protection
Please check the environment temperature
235
Power output over
temperature protection
Please check the environment temperature
236
Overcurrent Protection of
Power Output
Please check the environment temperature,
check copper row screw
237
Overcurrent Protection of
Power Output
Please check the environment temperature,
check copper row screw
238
Overcurrent Protection of
Power Output
Please check the environment temperature,
check copper row screw
239
Overvoltage Protection of
Power Output
Inspection of power supply in power grid
240
Low Voltage Protection for
Power Output
Inspection of power supply in power grid
241
Power output current
imbalance
Replace the power
243
Over-temperature
Protection for Power Input
Please check the environment temperature
244
Over-temperature
Protection for Power Input
Please check the environment temperature
245
Over-temperature
Protection for Power Input
Please check the environment temperature
246
Overcurrent Protection for
Power Input
Please check the environment temperature
247
Overcurrent Protection for
Power Input
Please check the environment temperature
248
Overvoltage Protection for
Power Input
Inspection of input voltage in power grid
249
Overvoltage Protection for
Power Input
Inspection of input voltage in power grid
250
Undervoltage Protection
for Power Input
Inspection of input voltage in power grid
251
Undervoltage Protection
for Power Input
Inspection of input voltage in power grid
253 Power Fan Error Replace the PSU
254 Power Fan Error Replace the PSU
255
Protection of over power
output
Please check the environment temperature
256
Protection of over power
output
Please check the environment temperature
257
Input over current
protection of power supply
primary side
Try to power off and restart, no effect to
replace the power supply
263
Power communication
warning
Check whether the screws of the control
board are locked
264 Power communication error
Check whether the screws of the control
board are locked
267 Power watchdog protection Contact the technician in time
268
Power output over-current
protection
Check the ambient temperature, check the
copper bar screw
269
Power input over-current
protection
Improve power supply conditions and input
voltage
270
Power input over-voltage
protection
Inspection of input voltage in power grid
271
Power input under-voltage
protection
Inspection of input voltage in power grid
272
Warning of excessive power
output of power supply
Please check the environment temperature
273
Power input power too high
warning
Please check the environment temperature
274 Power fan warning
Check if the power fan is blocked and may
need to be replaced
275
Power over temperature
warning
Please check the environment temperature
300
SM0 temperature sensor
detection error
Check the connection of the hashboard
301
SM1 temperature sensor
detection error
Check the connection of the hashboard
302
SM2 temperature sensor
detection error
Check the connection of the hashboard
320
SM0 temperature reading
error
Check whether the control board screw is
locked properly, check the connection board
and the arrangement contact
321
SM1 temperature reading
error
Check whether the control board screw is
locked properly, check the connection board
and the arrangement contact
322
SM2 temperature reading
error
Check whether the control board screw is
locked properly, check the connection board
and the arrangement contact
329
Control board temperature
sensor communication error
Replace the power supply
350 SM0 temperature protecting Please check the environment temperature
351 SM1 temperature protecting Please check the environment temperature
352 SM2 temperature protecting Please check the environment temperature
410 SM0 detect eeprom error Check adapter board and wiring contact
411 SM1 detect eeprom error Check adapter board and wiring contact
412 SM2 detect eeprom error Check adapter board and wiring contact
420 SM0 parser eeprom error Contact the technician in time
421 SM1 parser eeprom error Contact the technician in time
422 SM2 parser eeprom error Contact the technician in time
430 SM0 chip bin type error Contact the technician in time
431 SM1 chip bin type error Contact the technician in time
432 SM2 chip bin type error Contact the technician in time
440
SM0 eeprom chip num X
error
Contact the technician in time
441
SM1 eeprom chip num X
error
Contact the technician in time
442
SM2 eeprom chip num X
error
Contact the technician in time
510 SM0 miner type error
The version and type of hashboard are
inconsistent, replace the correct hashboard
511 SM1 miner type error
The version and type of hashboard are
inconsistent, replace the correct hashboard
512 SM2 miner type error
The version and type of hashboard are
inconsistent, replace the correct hashboard
530 SM0 not found
Check the connection and arrangement of the
adapter board, or replace the control
board, check whether the hash board
connector is empty welded
531 SM1 not found
Check the connection and arrangement of the
adapter board, or replace the control
board, check whether the hash board
connector is empty welded
532 SM2 not found
Check the connection and arrangement of the
adapter board, or replace the control
board, check whether the hash board
connector is empty welded
540 SM0 reading chip id error
Check adapter board and wiring contact,
Clean the dust on the hashboard
541 SM1 reading chip id error
Check adapter board and wiring contact,
Clean the dust on the hashboard
542 SM2 reading chip id error
Check adapter board and wiring contact,
Clean the dust on the hashboard
550 SM0 have bad chips Replacement of bad chips
551 SM1 have bad chips Replacement of bad chips
552 SM2 have bad chips Replacement of bad chips
560 SM0 loss balance
Plug in the adapter plate, and then screw
in the power connection hashboard again
561 SM1 loss balance
Plug in the adapter plate, and then screw
in the power connection hashboard again
562 SM2 loss balance
Plug in the adapter plate, and then screw
in the power connection hashboard again
600
Environment temperature is
high
Please check the environment temperature
610
If the ambient temperature
is too high in high
performance mode, return
to normal mode
Check the ambient temperature, high
performance mode needs to be controlled
below 30 ?
710
Control board rebooted as
exception
Updating the latest firmware.Check whether
the control board screw is locked properly
800 cgminer checksum error Re-upgrade firmware
801
system-monitor checksum
error
Re-upgrade firmware
802
remote-daemon checksum
error
Re-upgrade firmware
2010 All pools are disable Please check the network or pools configure
2020 Pool0 connect failed Please check the network or pools configure
2021 Pool1 connect failed Please check the network or pools configure
2022 Pool2 connect failed Please check the network or pools configure
2030
High rejection rate of
pool
Please check the network or pools
configure.Setting of mining currency
2040
The pool does not support
the asicboost mode
Check pool configuration
5110 SM0 Frequency Up Timeout reboot
5111 SM1 Frequency Up Timeout reboot
5112 SM2 Frequency Up Timeout reboot
8410
Software version error
(M2x miner with M3x
firmware, or M3x with M2x
firmware).
Upgrade to the correct firmware version
PSU
Error
code
Reason processing method
0x0001 Input undervoltage Check the power supply
0x0002
Temperature sampling over
temperature protection of
power radiator
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0004
Temperature sampling over
temperature protection of
power radiator
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0008
Over temperature
protection of
environmental temperature
sampling in power supply
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0010 Primary side over current
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0020 Output undervoltage Check the power supply
0x0040
Output over current
(continuous load 320A for
more than 2S)
Tighten the copper bar screw again
0x0080 Primary side over current
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0100
Single circuit overcurrent
(protection point 120a)
Check the PSU
0x0200
Single circuit overcurrent
(protection point 120a)
Check the PSU
0x0400
Single circuit overcurrent
(protection point 120a)
Check the PSU
0x0800 Fan failure Replace the PSU
0x1000
Output over current
(continuous load of 310A
for more than 5min)
Check the PSU
0x2000
Output over current
(continuous load 295A for
more than 10min)
Check the PS
Error code Reason Processing method 110 Fanin detect speed error Check whether the fan connection is normal, or replace the power supply, or replace the fan 111 Fanout detect speed error Check whether the fan connection is normal, or replace the power supply, or replace the fan 130 Fanin speed error Check whether the fan connection is normal, or replace the power supply, or replace the fan 131 Fanout speed error Check whether the fan connection is normal, or replace the power supply, or replace the fan 140 Fan speed is too high Please check the environment temperature 200 Power probing error, no power found Detecting power output wiring, updating the latest firmware, or replacing power supply 201 Power supply and configuration file mismatch Replace the correct PSU 203 Power protecting Please check the environment temperature 204 Power current protecting Please check the environment temperature 205 Power current error Inspection of power supply in power grid 206 Power input voltage is low Improve power supply conditions and input voltage 207 Power input current protecting Improve power supply conditions and input voltage 210 Power error status Check power failure code 213 Power input voltage and current do not match the power Replace the PSU 233 Power output over temperature protection Please check the environment temperature 234 Power output over temperature protection Please check the environment temperature 235 Power output over temperature protection Please check the environment temperature 236 Overcurrent Protection of Power Output Please check the environment temperature, check copper row screw 237 Overcurrent Protection of Power Output Please check the environment temperature, check copper row screw 238 Overcurrent Protection of Power Output Please check the environment temperature, check copper row screw 239 Overvoltage Protection of Power Output Inspection of power supply in power grid 240 Low Voltage Protection for Power Output Inspection of power supply in power grid 241 Power output current imbalance Replace the power 243 Over-temperature Protection for Power Input Please check the environment temperature 244 Over-temperature Protection for Power Input Please check the environment temperature 245 Over-temperature Protection for Power Input Please check the environment temperature 246 Overcurrent Protection for Power Input Please check the environment temperature 247 Overcurrent Protection for Power Input Please check the environment temperature 248 Overvoltage Protection for Power Input Inspection of input voltage in power grid 249 Overvoltage Protection for Power Input Inspection of input voltage in power grid 250 Undervoltage Protection for Power Input Inspection of input voltage in power grid 251 Undervoltage Protection for Power Input Inspection of input voltage in power grid 253 Power Fan Error Replace the PSU 254 Power Fan Error Replace the PSU 255 Protection of over power output Please check the environment temperature 256 Protection of over power output Please check the environment temperature 257 Input over current protection of power supply primary side Try to power off and restart, no effect to replace the power supply 263 Power communication warning Check whether the screws of the control board are locked 264 Power communication error Check whether the screws of the control board are locked 267 Power watchdog protection Contact the technician in time 268 Power output over-current protection Check the ambient temperature, check the copper bar screw 269 Power input over-current protection Improve power supply conditions and input voltage 270 Power input over-voltage protection Inspection of input voltage in power grid 271 Power input under-voltage protection Inspection of input voltage in power grid 272 Warning of excessive power output of power supply Please check the environment temperature 273 Power input power too high warning Please check the environment temperature 274 Power fan warning Check if the power fan is blocked and may need to be replaced 275 Power over temperature warning Please check the environment temperature 300 SM0 temperature sensor detection error Check the connection of the hashboard 301 SM1 temperature sensor detection error Check the connection of the hashboard 302 SM2 temperature sensor detection error Check the connection of the hashboard 320 SM0 temperature reading error Check whether the control board screw is locked properly, check the connection board and the arrangement contact 321 SM1 temperature reading error Check whether the control board screw is locked properly, check the connection board and the arrangement contact 322 SM2 temperature reading error Check whether the control board screw is locked properly, check the connection board and the arrangement contact 329 Control board temperature sensor communication error Replace the power supply 350 SM0 temperature protecting Please check the environment temperature 351 SM1 temperature protecting Please check the environment temperature 352 SM2 temperature protecting Please check the environment temperature 410 SM0 detect eeprom error Check adapter board and wiring contact 411 SM1 detect eeprom error Check adapter board and wiring contact 412 SM2 detect eeprom error Check adapter board and wiring contact 420 SM0 parser eeprom error Contact the technician in time 421 SM1 parser eeprom error Contact the technician in time 422 SM2 parser eeprom error Contact the technician in time 430 SM0 chip bin type error Contact the technician in time 431 SM1 chip bin type error Contact the technician in time 432 SM2 chip bin type error Contact the technician in time 440 SM0 eeprom chip num X error Contact the technician in time 441 SM1 eeprom chip num X error Contact the technician in time 442 SM2 eeprom chip num X error Contact the technician in time 510 SM0 miner type error The version and type of hashboard are inconsistent, replace the correct hashboard 511 SM1 miner type error The version and type of hashboard are inconsistent, replace the correct hashboard 512 SM2 miner type error The version and type of hashboard are inconsistent, replace the correct hashboard 530 SM0 not found Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded 531 SM1 not found Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded 532 SM2 not found Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded 540 SM0 reading chip id error Check adapter board and wiring contact, Clean the dust on the hashboard 541 SM1 reading chip id error Check adapter board and wiring contact, Clean the dust on the hashboard 542 SM2 reading chip id error Check adapter board and wiring contact, Clean the dust on the hashboard 550 SM0 have bad chips Replacement of bad chips 551 SM1 have bad chips Replacement of bad chips 552 SM2 have bad chips Replacement of bad chips 560 SM0 loss balance Plug in the adapter plate, and then screw in the power connection hashboard again 561 SM1 loss balance Plug in the adapter plate, and then screw in the power connection hashboard again 562 SM2 loss balance Plug in the adapter plate, and then screw in the power connection hashboard again 600 Environment temperature is high Please check the environment temperature 610 If the ambient temperature is too high in high performance mode, return to normal mode Check the ambient temperature, high performance mode needs to be controlled below 30 ℃ 710 Control board rebooted as exception Updating the latest firmware.Check whether the control board screw is locked properly 800 cgminer checksum error Re-upgrade firmware 801 system-monitor checksum error Re-upgrade firmware 802 remote-daemon checksum error Re-upgrade firmware 2010 All pools are disable Please check the network or pools configure 2020 Pool0 connect failed Please check the network or pools configure 2021 Pool1 connect failed Please check the network or pools configure 2022 Pool2 connect failed Please check the network or pools configure 2030 High rejection rate of pool Please check the network or pools configure.Setting of mining currency 2040 The pool does not support the asicboost mode Check pool configuration 5110 SM0 Frequency Up Timeout reboot 5111 SM1 Frequency Up Timeout reboot 5112 SM2 Frequency Up Timeout reboot 8410 Software version error (M2x miner with M3x firmware, or M3x with M2x firmware). Upgrade to the correct firmware version PSU Error code Reason processing method 0x0001 Input undervoltage Check the power supply 0x0002 Temperature sampling over temperature protection of power radiator Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0004 Temperature sampling over temperature protection of power radiator Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0008 Over temperature protection of environmental temperature sampling in power supply Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0010 Primary side over current Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0020 Output undervoltage Check the power supply 0x0040 Output over current (continuous load 320A for more than 2S) Tighten the copper bar screw again 0x0080 Primary side over current Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0100 Single circuit overcurrent (protection point 120a) Check the PSU 0x0200 Single circuit overcurrent (protection point 120a) Check the PSU 0x0400 Single circuit overcurrent (protection point 120a) Check the PSU 0x0800 Fan failure Replace the PSU 0x1000 Output over current (continuous load of 310A for more than 5min) Check the PSU 0x2000 Output over current (continuous load 295A for more than 10min) Check the PS
300
Ошибка обнаружения датчика температуры SM0
Проверьте подключение хэш-платы
301
Ошибка обнаружения датчика температуры SM1
302
Ошибка обнаружения датчика температуры SM2
320
Ошибка связи с датчиком температуры платы SM0
Проверьте, заблокированы ли винты панели управления, проверьте переходную пластину и контакты кабеля
321
Ошибка связи с датчиком температуры платы SM1
322
Ошибка связи с датчиком температуры платы SM2
329
Температура платы управления ошибка связи с датчиком
Замените источник питания
350
Защита от перегрева SM0
Проверьте температуру окружающей среды (рекомендуется использовать инфракрасный термометр GS320).
351
SM1 защита от перегрева
352
SM2 защита от перегрева
360
Температура хэш-платы перегревается
410
SMO обнаружило ошибку eeprom
Проверьте переходную пластину и контакт кабеля
411
SM1 обнаружило ошибку eeprom
412
SM2 обнаружило ошибку eeprom
420
SM0 ошибка синтаксического анализатора eeprom
Обновить прошивку
421
SM1 ошибка синтаксического анализатора eeprom
422
M2 ошибка eeprom синтаксического анализатора
430
Ошибка типа бина микросхемы SM0
431
Ошибка типа бина микросхемы SM1
432
Ошибка типа буфера микросхемы SM2
440
Ошибка SM0 eeprom chip num X
441
Ошибка SM1 eeprom chip num X
442
SM2 номер микросхемы eeprom X ошибка
450
SM0 eeprom xfer error
Проверьте плату адаптера и контакты проводки.Обновите прошивку
451
SM1 eeprom xfer error
452
SM2 eeprom xfer error
510
SM0 ошибка типа майнера
Версия и тип хэшборда несовместимы, замените правильный хэшборд
511
SM1 ошибка типа майнера
512
Ошибка типа майнера SM2
520
Ошибка типа бина SM0
Если тип чипа хэш-платы несовместим, замените правильную хэш-плату
521
Ошибка типа бина SM1
522
Ошибка типа бина SM2
530
Плата SM0 не обнаружена
Проверьте проводку платы адаптера и кабель, или замените плату управления, чтобы проверить, припаян
ли
разъем хэш-платы.
531
Плата SM1 не обнаружена
532
Плата SM2 не обнаружена
540
Количество микросхем SM0 неполное
Проверьте переходную пластину и контакт кабеля
541
Количество микросхем SM1 неполное
542
Количество микросхем SM2 неполное
550
SM0 имеет плохие чипы
Замените плохую микросхему в позиции печати
551
SM1 имеет плохие чипы
552
SM2 имеет плохие чипы
560
SM0 потеря баланса
Подключите переходную пластину, а затем снова прикрутите хэш-плату для подключения питания
561
SM1 потеря баланса
562
SM2 потеря баланса
590
Частота SM0 слишком низкая
Замените хэш-плату и поместите вместе хэш-платы, которые сообщили об одной и той же ошибке
591
Частота SM1 слишком низкая
592
Частота SM2 слишком низкая
600
Слишком высокая температура окружающей среды
Проверьте температуру окружающей среды
610
Если температура окружающей среды слишком высока в режиме высокой производительности, вернитесь в
нормальный
режим
Проверьте температуру окружающей среды, в режиме высокой производительности должна быть ниже 30 ℃.
701
На плате управления отсутствует микросхема поддержки
Обновление соответствующего типа микропрограммы
710
Ошибка платы управления
Обновите до последней версии прошивки
712
Плата управления перезагрузилась как исключение
Обновление последней версии прошивки. Проверьте, правильно ли зафиксирован винт платы управления
800
Ошибка контрольной суммы cgminer
Обновление микропрограммы
801
Ошибка контрольной суммы системного монитора
802
Ошибка контрольной суммы системного монитора
2000
Не настроена информация о пуле
Проверьте конфигурацию пула
2010
Все подключения к пулам майнинга не удались
Проверьте настройки сети или пулов майнинга
2020
Не удалось установить соединение с пулом майнинга
2021
Не удалось установить соединение с пулом майнинга
2022
Не удалось установить соединение с пулом майнинга
2030
Скорость повторного срабатывания пула майнинга слишком высока
Проверьте настройки сети или пула майнинга, а также настройки майнинга криптовалюты
2040
Пул не поддерживает режим asicboost
Проверьте конфигурацию пула
2310
Хэшрейт слишком низкий
Проверьте входное напряжение, сетевое окружение и температуру окружающей среды.
2320
Скорость хэширования слишком низкая
2340
Потеря хэшрейта слишком высока
2350
Потеря скорости хэширования слишком высока
5070
Скорость потока воды SM0 ненормальная
Проверьте, нормальный ли поток воды
5071
SM1 Скорость течения воды ненормальная
5072
SM2 Скорость потока воды ненормальная
5110
SM0 Таймаут повышения частоты
Перезагрузите
5111
SM1 Таймаут повышения частоты
5112
SM2 Таймаут повышения частоты
8410
Ошибка версии программного обеспечения (miner M2x с прошивкой M3x или M3x с прошивкой M2x)
Обновление до правильной версии прошивки
100001
/antiv/signature illegal
Обновление до последней версии микропрограммы или запись карты
100002
/antiv/dig/initd.dig illegal
Обновление до последней версии микропрограммы или запись карты
100003
/antiv/dig/pf_partial.dig illegal
Обновление до последней версии микропрограммы или запись карты
Содержание
- Fan detect speed error #8
- Comments
- Whatsminer m21s fan in detect speed error
- Коды ошибок асик майнера WhatsMiner
Fan detect speed error #8
I’ve done everything as described, rooted the system, (running on latest firmware). using the init.d
I get this
110 | Fan in detect speed error | 2021-06-06 15:51:32
111 | Fan out detect speed error | 2021-06-06 15:51:32
130 | Fan in speed error, percent: 0, speed: 6000 | 2021-06-06 15:51:14
131 | Fan out speed error, percent: 0, speed: 6000 | 2021-06-06 15:51:14
The text was updated successfully, but these errors were encountered:
Most probably they’re had changed fan behavior for newest models, which one you’re trying to emulate fans?
Most probably they’re had changed fan behavior for newest models, which one you’re trying to emulate fans?
Hello and thank you so much for replying!
I’m trying to do this on a whatsminer m3v1
110 | Fan in detect speed error | 2021-12-03 20:16:21 |
111 | Fan out detect speed error | 2021-12-03 20:16:21 |
130 | Fan in speed error, percent: 0, speed: 6000 | 2021-12-03 20:16:03 |
131 | Fan out speed error, percent: 0, speed: 6000 | 2021-12-03 20:16:03 |
@CoCEmu which model of asic do you use? m3 or m3x?
You can also play around with FAN_PWM at
Also make sure the path is mounted running mount | grep fake_fan .
i’ll check it and tell you
i use m3v1
and i change /etc/config/fans
and set fan count = 1;
the i delete detail about fan1(becuse fan0 to first fan = fan0).
we need to use fan pwm for replace miner fan as power fan and we dont have to use maximum speed of fan.
do you know how can i set a fixed fan speed for fan1?
@CoCEmu which model of asic do you use? m3 or m3x? You can also play around with FAN_PWM at
try setting values from 5 and above it (5,10,15, etc.)
Also make sure the path is mounted running mount | grep fake_fan .
hello,
i changed FAN_PWM=5 and i got same response.after 30 second cgminer restarted.
110 | Fan in detect speed error | 2021-12-04 21:41:23
130 | Fan in speed error, percent: 0, speed: 6000 | 2021-12-04 21:41:05
Источник
Whatsminer m21s fan in detect speed error
Создано 03.10.2021 11:22
Коды ошибок асик майнера WhatsMiner
0 ErrSucc ОК ОК — обычный
21 ErrNotPlugged 1 или более хеш-плат не обнаружены Сигнал Hashboard PLUG не обнаружен Номер обнаруженной платы питания, если их более одной, разделенные пробелами 1. Проверьте правильность подключения кабеля SPI (по сравнению с обычной машиной) и снова подключите кабель. 2. Замените плату управления. 3. Замените проблемную доску хешрейта (переделайте доску головоломки).
22 ErrPsuI2cFail Аномальная связь по управлению питанием Неправильная связь I2C источника питания — 1. Заменить блок питания. 2. Замените плату управления.
23 ErrEncoreAllFail Все хэш-платы не могут быть включены SPI недоступен для всех плат хешрейта — 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Отремонтируйте всю машину.
24 ErrEncoreFail Некоторые платы не включаются SPI недоступен на некоторых хэш-досках Номер хэшборда, для которого произошел сбой связи по SPI, если их несколько, разделенных пробелами 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Замените проблемную хеш-доску (переделайте доску-головоломку).
25 ErrSetPllFail Не удалось поднять частоту хэш-платы Не удалось поднять частоту хэш-платы Номер хэшборда: частота ошибок 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Замените проблемную хеш-доску (переделайте доску-головоломку).
26 ErrSetVolFail Не удалось установить напряжение Не удалось установить напряжение Номер хэшборда: 1/2 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Заменить проблемную хеш-доску (присоединиться)
27 ErrBistFail Тест чипа BIST не пройден Тест чипа BIST не пройден Номер хэшборда: 1/2 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить проблемную хеш-доску (присоединиться к плате)
28 ErrSpiFail Ненормальная связь платы хешрейта не может быть автоматически восстановлена ??во время работы Ненормальное соединение SPI платы хешрейта не может быть автоматически восстановлено во время работы Номер хэшборда 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Замените проблемную хеш-доску (переделайте доску-головоломку)
29 ErrI2cFail Ненормальная связь по питанию во время работы не может быть восстановлена ??автоматически Связь I2C с ненормальным источником питания не может быть автоматически восстановлена ??во время работы — 1. Заменить блок питания. 2. Замените плату управления.
30 ErrNetwork Подключение к майнинговому пулу прервано Подключение к майнинговому пулу прервано — Если эта проблема возникает на большом количестве или на всех майнинговых машинах с одним и тем же коммутатором: 1. Проверьте правильность настроек пула для майнинга. 2. Проверьте конфигурацию сетевой среды (например, конфигурацию DHCP, конфигурацию DNS, порт и т. Д.). Если проблемы возникают только на одной или нескольких машинах для майнинга: 1. Проверьте правильность настроек пула для майнинга. 2. Проверить подключения к сетевому порту майнера. 3. Замените сетевой кабель на работающую майнинговую машину. 4. Замените плату управления.
31 ErrBadChip Повреждение отдельных микросхем, что приводит к искусственно завышенной вычислительной мощности Повреждение отдельных микросхем, что приводит к искусственно завышенной вычислительной мощности Номер поврежденной микросхемы: номер хеш-платы, если их более одной, разделенные пробелами В ремонт
32 ErrOverheat Hashboard перегрелся Hashboard перегрелся Номер хэшборда 1. Проверьте, вращаются ли передний и задний вентиляторы, если они не вращаются, сначала замените вентиляторы, а затем замените плату управления / блок питания. 2. Убедитесь, что направление ветра спереди и сзади согласовано, согласуется ли оно с другими машинами, если нет, измените направление вентилятора. 3. Если температура воздуха на входе горной машины превышает 40 градусов, необходимо улучшить температурную среду в шахте. 4. Если определенная плата хешрейта часто перегревается, вы можете заменить проблемную плату хешрейта (переделайте головоломку).
33 ErrInvTemp Невозможно прочитать температуру чипа Невозможно прочитать температуру чипа Номер хэшборда 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Замените проблемную хеш-доску (переделайте доску-головоломку).
34 ErrMisPlugged Неправильное подключение кабеля связи платы управления Ненормальное подключение кабеля SPI платы управления Номер хэшборда 1. Проверьте, совместим ли метод (последовательность) подключения кабеля SPI хэш-платы с другими машинами той же модели. 2. Замените плату управления.
35 ErrPsuFail Аномальный источник питания Аномальный источник питания 1. Обратите внимание на то, что если нет явного отклонения от нормы вычислительной мощности всей машины (не отключается плата), то перезагрузить 2. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 3. Заменить блок питания.
36 ErrInvCorenum Некоторые чипы не работают должным образом Количество хороших фишек ненормальное Номер хэшборда: номер чипа 1. Обратите внимание на то, что если нет явного отклонения от нормы вычислительной мощности всей машины (не отключается плата), то перезагрузить 2. Перезапустите майнер, чтобы увидеть, появляется ли по-прежнему та же ошибка. 3. Замените проблемную хеш-плату.
37 ErrInvVidtype Тип платы управления / версия прошивки / количество микросхем не совпадает Тип платы управления / версия прошивки / количество микросхем не совпадает vidtype, minertype, subtype, chipnum После накопления нескольких единиц (> 10) обратитесь в ремонт.
38 ErrBadRearChips Наконец, у некоторых чипов низкая вычислительная мощность. Последние несколько уровней чипов имеют низкую вычислительную мощность В ремонт
39 ErrInvTuneParam Аномальные параметры старения Напряжение начальной частоты старения неверно В ремонт
Errcode | Scope of application | Explanation | Troubleshooting steps |
Whole miner | Normal | Normal | |
21 | hashboard | one or more hashboards can’t be detected | 1. check and see whether the SPI cables are firmly and correctly connected (compared the connection of cables with working miners), reconnect the SPI cables, don’t change sequence of connection 2. replace control board with other well functional one 3. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
22 | Whole miner | PSU communication is abnormal | 1. replace PSU with other well functional one 2. replace control board with other well functional one |
23 | Whole miner | All hashboards can’t be powered up | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. whole miner should be returned for repair |
24 | hashboard | one or more hashboards can’t be powered up | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
25 | hashboard | frequency increase of hashboards fails | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check and see whether screws on the PSU side and SPI connection are loose 3. replace PSU with other well functional one 4. replace control board with other well functional one 5. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
26 | hashboard | voltage setting fails | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
27 | hashboard | chip BIST test fails | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
28 | hashboard | abnormal communication of hashboard, it can’t be automatically recovered when running | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
29 | Whole miner | abnormal communication of PSU can’t be automatically recovered when running | 1. replace PSU with other well functional one 2. replace control board with other well functional one |
30 | Whole miner | pool disconnect | If the problem occurs in a large number of miners or all of the mines under the same switch: 1. please first check whether pool setting is correct 2. then check network configuration (such as DHCP configuration, DNS configuration, ports, etc.) If the problem occurs in only one or just a small number of miners under the same switch: 1. please first check whether pool setting is correct 2. then check whether network cable is firmly connected 3. replace network cable with other one from other well working miner 4. replace control board with other well functional one |
31 | hashboard | damage of some individual chip causes inflated high hashrate of the miner | no action should be taken |
32 | hashboard | hashboard overheat | 1. check and see whether both fans are spinning, if not, replace fan with other functional one, if still not, then replace control board or PSU 2. check and see whether wind direction of both fans are the same, whether wind direction are the same with other miners, if not, exchange fans 3. meter the inlet temperature of the miner, if above 40 °C, cooling system of the mining farm should be improved 4. if some hashboard is overheated frequently, that hashboard should be replaced (returned for repair) |
33 | hashboard | chip temperature can’t be read | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
34 | cables of control board is connected incorrectly | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check whether hashboard SPI cables are conneted in the same way (sequence) as other miners of same model 3. replace control board with other well functional one |
|
35 | hashboard | PSU voltage is too low | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2.check and see whether screws on the PSU side and SPI connection is loose 3. replace PSU with other well functional one |
36 | hashboard | working or some chips is abnormal | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. reboot the miner to see whether the same error is given 3. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
37 | Whole miner | mismatch of control board version/firmware version/quantity of chips | if there are more than 10 miners with same error, please contact engineers |
38 | hashboard | low hashrate of last few chips | no action should be taken |
39 | hashboard | testing parameter is abnormal | no action should be taken |
40 | hashboard | PSU load is insufficient | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
41 | hashboard | startup voltage of PSU is too low | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check and see whether screws on the PSU side and SPI connection are loose 3. replace PSU with other well functional one 4. replace control board with other well functional one |
42 | hashboard | implementation of plan B fails when hashboard frequency increases | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check and see whether screws on the PSU side and SPI connection are loose 3. replace PSU with other well functional one 4. replace control board with other well functional one 5. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
Attention: 1. The miner should be powered up again to see whether it is back to normal after every step is taken 2. If the problem is not solve after replacement the part, the part should go back to its original unit 3. Error code and brief description of the problem should be attached to the hashboard that is confirmed defective and that will be returned for repair |
Reason Processing method
110 Fanin detect speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
111 Fanout detect speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
130 Fanin speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
Источник
Here is the WhatsMiner checklist of error code and we strongly recommend every WhatsMiner user to keep it because almost 80% of the problems can be solved by corresponding solutions.
We hope it is helpful for all WhatsMiner users. For rest of the problems, Kindly reach us and we’re willing to help.
Meaning of Error Code and Corresponding Solutions on WhatsM liner Tool 1 |
||
Error Code |
Meaning |
Corresponding Solutions |
110 |
Inlet fan detcction speed error |
Check whether the fan connction is normal, or replace the power supply, or replace the fan |
111 |
Outlet fan detection speed error |
|
120 | Inlet fan speed error(Deviation 2000+) | |
121 | Outlet fan speed error(Deviation 2000+) | |
130 |
Inlet fan speed error |
|
131 |
Outlet fan spced error |
|
140 |
Fan speed is too high |
Please check the environment temperature |
200 |
Power detection error |
Detecting the power output cable, or updating the latest firmware, or replacing the power supply |
201 |
Power does not match the configuration file |
Updating to the latest software |
202 |
Power output voltage error |
Updating to the latest software or check the power supply |
203 |
Power supply protection |
Please check the environment temperature |
204 |
Power supply current protection |
|
205 |
Power current error |
Inspection of power supply in power grid |
206 |
Power input voltage is low |
Improve power supply conditions and input voltage |
207 |
Power input current protecting |
|
210 |
Power status error |
Check the power failure code |
213 |
Power input voltage and current do not match the power |
Replace the PSU |
216 | Power remained unchanged for a long time | |
217 | Power set enable error | |
218 | Power input voltage is lower than 230V for high power mode | Increase input voltage,replace power supply |
233 |
Overtemperature Protection of Power Output |
Plcase check the environment temperature |
234 |
Overtemperature Protection of Power Output |
|
235 |
Overtemperature Protection of Power Output |
|
236 |
Overcurrent Protection of Power Output |
Please check the environment temperature and the copper wire screw(Recommend to use the protable electric screwdriver) |
237 |
Overcurrent Protection of Power Output |
|
238 |
Overcurrent Protection of Power Output |
|
239 |
Overvoltage Protection of Power Output |
Check grid power |
240 |
Low Voltage Protection for Power Output |
|
241 |
Power output current imbalance |
Replace the power |
243 |
Over-tempcrature Protection for Power Input |
Please check the environment temperature |
244 |
Over-temperature Protection for Power Input |
|
245 |
Over-tempcrature Protection for Power Input |
|
246 |
Overcurrent Protection for Power Input |
|
247 |
Overcurrent Protection for Power Input |
|
248 |
Overvoltage Protection for Power Input |
Check grid power |
249 |
Overvoltage Protection for Power Input |
|
250 |
Undervoltage Protection for Power Input |
|
251 |
Undervoltage Protection for Power Input |
|
253 |
Power Fan Error |
Replace the power supply |
254 |
Power Fan Error |
|
255 |
Protection of over power output |
Please check the environment temperature |
256 |
Protection of over power output |
|
257 |
Input over current protection of power supply primary side |
Try to power off and restart, no effect to replace the power supply |
263 |
Power communication warning |
Check whether the screws of the control board are locked |
264 |
Power communication error |
|
267 |
Power watchdog protection |
Contact the technician in time |
268 |
Power output over-current protection |
Check the ambient temperature, check the copper bar screw |
269 |
Power input over-current protection |
Improve power supply conditions and input voltage |
270 |
Power input over-voltage protection |
Inspection of input voltage in power grid |
271 |
Power input under-voltage protection |
|
272 |
Warning of excessive power output of power supply |
Please check the environment temperature |
273 |
Power input power too high warning |
|
274 |
Power fan warning |
Check if the power fan is blocked and may need to be replaced |
275 |
Power over temperature warning |
Please check the environment temperature |
Meaning of Error Code and Corresponding Solutions on WhatsMiner Tool 2 |
||
Error Code |
Meaning |
Corresponding Solutions |
300 |
SM0 temperature sensor detection error |
Check the connection of the hash board |
301 |
SM1 temperature sensor detection error |
|
302 |
SM2 temperature sensor detection error |
|
320 |
SM0 board temperature sensor communication error |
Check if the control panel screws are locked, check the adapter plate and the cable contacts |
321 |
SM1 board temperature sensor communication error |
|
322 |
SM2 board temperature sensor communication error |
|
329 |
Control board temperature sensor communication error |
Replace the power supply |
350 |
SM0 tempcrature protection |
Check the environment temperature (Recommend to use the GS320 infrared thermometer) |
351 |
M1 tempcrature protection |
|
352 |
SM2 tempcrature protection |
|
360 | The temperature of the hash board is overheating | |
410 |
SMO detect eeprom error |
Check adapter plate and cable contact |
411 |
SM1 detect eeprom error |
|
412 |
SM2 detect eeprom error |
|
420 |
SM0 parser eeprom error |
Upgrade firmware |
421 |
SM1 parser eeprom error |
|
422 |
SM2 parser eeprom error |
|
430 |
SM0 chip bin type error |
|
431 |
SM1 chip bin type error |
|
432 |
SM2 chip bin type error |
|
440 |
SM0 eeprom chip num X error |
|
441 |
SM1 eeprom chip num X error |
|
442 |
SM2 eeprom chip num X error |
|
450 | SM0 eeprom xfer error | Check adapter board and wiring contacts.Upgrade firmware |
451 | SM1 eeprom xfer error | |
452 | SM2 eeprom xfer error | |
510 |
SM0 miner type error |
The version and type of hashboard are inconsistent, replace the correct hashboard |
511 |
SM1 miner type error |
|
512 |
SM2 miner type error |
|
520 | SM0 bin type error | If the chip type of the hash board is inconsistent, replace the correct hash board. |
521 | SM1 bin type error | |
522 | SM2 bin type error | |
530 |
SM0 board is not detected |
Check the adapter board wiring and cablc, or replace the control board to check whether the hash board connector is soldered |
531 |
SM1 board is not detected |
|
532 |
SM2 board is not detected |
|
540 |
The number of SM0 chips is incomplete |
Check adapter plate and cable contact |
541 |
The number of SM1 chips is incomplete |
|
542 |
The number of SM2 chips is incomplete |
|
550 |
SM0 has bad chips |
Replace the bad chip in the print position |
551 |
SM1 has bad chips |
|
552 |
SM2 has bad chips |
|
560 |
SM0 loss balance |
Plug in the adapter plate, and then screw in the power connection hash board again |
561 |
SM1 loss balance |
|
562 |
SM2 loss balance |
|
590 |
SM0 frequency is too low |
Replace the hash board and place the hash boards which reported the same error together |
591 |
SM1 frequency is too low |
|
592 |
SM2 frequency is too low |
|
600 |
Environment temperature is too high |
Check the environment temperature |
610 |
If the ambient temperature is too high in high performance mode, return to normal mode |
Check the ambient temperature, high performance mode needs to be ontrolled below 30 ℃ |
701 | Control board no support chip | Upgrade the corresponding type of firmware |
710 |
Control board error |
Update to the latest firmware |
712 | Control board rebooted as exception | Updating the latest firmware.Check whether the control board screw is locked properly |
800 |
cgminer checksum error |
Re-upgrade firmware |
801 |
system-monitor checksum error |
|
802 |
system-monitor checksum error |
|
2000 | No pool information configured | Check pool configuration |
2010 |
All mining pool connections failed |
Check the network or mining pools setting |
2020 |
Mining pool0 connection failed |
|
2021 |
Mining pool1 connection failed |
|
2022 |
Mining pool2 connection failed |
|
2030 |
Mining pool rejcction rate is too high |
Check the network or mining pool setting, and the mining setting of the cryptocurrency |
2040 |
The pool does not support the asicboost mode |
Check pool configuration |
2310 | Hash rate is too low | Check input voltage, network environment, and ambient temperature |
2320 | Hash rate is too low | |
2340 | The loss of hash rate is too high | |
2350 | The loss of hash rate is too high | |
5070 | SM0 water velocity is abnormal | Check if the water flow is normal |
5071 | SM1 water velocity is abnormal | |
5072 | SM2 water velocity is abnormal | |
5110 |
SM0 Frequency Up Timeout |
reboot |
5111 |
SM1 Frequency Up Timeout |
|
5112 |
SM2 Frequency Up Timeout |
|
8410 | Software version error (M2x miner with M3x firmware, or M3x with M2x firmware) | Upgrade to the correct firmware version |
100001 | /antiv/signature Illegal | Upgrade the latest firmware or burn the card |
100002 | /antiv/dig/initd.dig Illegal | |
100003 |
/antiv/dig/pf_partial.dig Illegal |
PSU Error code |
Reason |
processing method |
0x0001 |
Input undervoltage |
Check the power supply |
0x0002 |
Temperature sampling over temperature protection of power radiator |
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply |
0x0004 |
Temperature sampling over temperature protection of power radiator |
|
0x0008 |
Over temperature protection of environmental emperature sampling in power supply |
|
0x0010 |
Primary side over current |
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply |
0x0020 |
Output undervoltage |
Check the power supply |
0x0040 |
Output over current (continuous load 320A for more than 2S) |
Tighten the copper bar screw again |
0x0080 |
Primary side over current |
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply |
0x0100 |
Single circuit overcurrent (protection point 120a) |
Check the PSU |
0x0200 |
Single circuit overcurrent (protection point 120a) |
|
0x0400 |
Single circuit overcurrent (protection point 120a) |
|
0x0800 |
Fan failure |
Replace the PSU |
0x1000 |
Output over current (continuous load of 310A for more than 5min) |
Check the PSU |
0x2000 |
Output over current (continuous load 295A for more than 10min) |
We hope it is helpful for all WhatsMiner users. For rest of the problems, Kindly reach us and we’re willing to help.
300
Ошибка обнаружения датчика температуры SM0
Проверьте подключение хэш-платы
301
Ошибка обнаружения датчика температуры SM1
302
Ошибка обнаружения датчика температуры SM2
320
Ошибка связи с датчиком температуры платы SM0
Проверьте, заблокированы ли винты панели управления, проверьте переходную пластину и контакты кабеля
321
Ошибка связи с датчиком температуры платы SM1
322
Ошибка связи с датчиком температуры платы SM2
329
Температура платы управления ошибка связи с датчиком
Замените источник питания
350
Защита от перегрева SM0
Проверьте температуру окружающей среды (рекомендуется использовать инфракрасный термометр GS320).
351
SM1 защита от перегрева
352
SM2 защита от перегрева
360
Температура хэш-платы перегревается
410
SMO обнаружило ошибку eeprom
Проверьте переходную пластину и контакт кабеля
411
SM1 обнаружило ошибку eeprom
412
SM2 обнаружило ошибку eeprom
420
SM0 ошибка синтаксического анализатора eeprom
Обновить прошивку
421
SM1 ошибка синтаксического анализатора eeprom
422
M2 ошибка eeprom синтаксического анализатора
430
Ошибка типа бина микросхемы SM0
431
Ошибка типа бина микросхемы SM1
432
Ошибка типа буфера микросхемы SM2
440
Ошибка SM0 eeprom chip num X
441
Ошибка SM1 eeprom chip num X
442
SM2 номер микросхемы eeprom X ошибка
450
SM0 eeprom xfer error
Проверьте плату адаптера и контакты проводки.Обновите прошивку
451
SM1 eeprom xfer error
452
SM2 eeprom xfer error
510
SM0 ошибка типа майнера
Версия и тип хэшборда несовместимы, замените правильный хэшборд
511
SM1 ошибка типа майнера
512
Ошибка типа майнера SM2
520
Ошибка типа бина SM0
Если тип чипа хэш-платы несовместим, замените правильную хэш-плату
521
Ошибка типа бина SM1
522
Ошибка типа бина SM2
530
Плата SM0 не обнаружена
Проверьте проводку платы адаптера и кабель, или замените плату управления, чтобы проверить, припаян
ли
разъем хэш-платы.
531
Плата SM1 не обнаружена
532
Плата SM2 не обнаружена
540
Количество микросхем SM0 неполное
Проверьте переходную пластину и контакт кабеля
541
Количество микросхем SM1 неполное
542
Количество микросхем SM2 неполное
550
SM0 имеет плохие чипы
Замените плохую микросхему в позиции печати
551
SM1 имеет плохие чипы
552
SM2 имеет плохие чипы
560
SM0 потеря баланса
Подключите переходную пластину, а затем снова прикрутите хэш-плату для подключения питания
561
SM1 потеря баланса
562
SM2 потеря баланса
590
Частота SM0 слишком низкая
Замените хэш-плату и поместите вместе хэш-платы, которые сообщили об одной и той же ошибке
591
Частота SM1 слишком низкая
592
Частота SM2 слишком низкая
600
Слишком высокая температура окружающей среды
Проверьте температуру окружающей среды
610
Если температура окружающей среды слишком высока в режиме высокой производительности, вернитесь в
нормальный
режим
Проверьте температуру окружающей среды, в режиме высокой производительности должна быть ниже 30 ℃.
701
На плате управления отсутствует микросхема поддержки
Обновление соответствующего типа микропрограммы
710
Ошибка платы управления
Обновите до последней версии прошивки
712
Плата управления перезагрузилась как исключение
Обновление последней версии прошивки. Проверьте, правильно ли зафиксирован винт платы управления
800
Ошибка контрольной суммы cgminer
Обновление микропрограммы
801
Ошибка контрольной суммы системного монитора
802
Ошибка контрольной суммы системного монитора
2000
Не настроена информация о пуле
Проверьте конфигурацию пула
2010
Все подключения к пулам майнинга не удались
Проверьте настройки сети или пулов майнинга
2020
Не удалось установить соединение с пулом майнинга
2021
Не удалось установить соединение с пулом майнинга
2022
Не удалось установить соединение с пулом майнинга
2030
Скорость повторного срабатывания пула майнинга слишком высока
Проверьте настройки сети или пула майнинга, а также настройки майнинга криптовалюты
2040
Пул не поддерживает режим asicboost
Проверьте конфигурацию пула
2310
Хэшрейт слишком низкий
Проверьте входное напряжение, сетевое окружение и температуру окружающей среды.
2320
Скорость хэширования слишком низкая
2340
Потеря хэшрейта слишком высока
2350
Потеря скорости хэширования слишком высока
5070
Скорость потока воды SM0 ненормальная
Проверьте, нормальный ли поток воды
5071
SM1 Скорость течения воды ненормальная
5072
SM2 Скорость потока воды ненормальная
5110
SM0 Таймаут повышения частоты
Перезагрузите
5111
SM1 Таймаут повышения частоты
5112
SM2 Таймаут повышения частоты
8410
Ошибка версии программного обеспечения (miner M2x с прошивкой M3x или M3x с прошивкой M2x)
Обновление до правильной версии прошивки
100001
/antiv/signature illegal
Обновление до последней версии микропрограммы или запись карты
100002
/antiv/dig/initd.dig illegal
Обновление до последней версии микропрограммы или запись карты
100003
/antiv/dig/pf_partial.dig illegal
Обновление до последней версии микропрограммы или запись карты
Error code
Reason
Processing method
Причина
Способ устранения
110
Fanin detect speed error
Check whether the fan connection is normal, or replace the power supply, or replace the
fan
Ошибка обнаружения скорости вращения вентилятора на входе
Проверьте, правильно ли подключен вентилятор, исправен ли он. Замените источник питания, или замените вентилятор
111
Fanout detect speed error
Check whether the fan connection is normal, or replace the power supply, or replace the
fan
Ошибка обнаружения скорости вращения вентилятора на выходе
Проверьте, правильно ли подключен вентилятор, исправен ли он. Замените источник питания, или замените вентилятор
130
Fanin speed error
Check whether the fan connection is normal, or replace the power supply, or replace the
fan
Ошибка скорости вращения вентилятора на входе
Проверьте, правильно ли подключен вентилятор, исправен ли он. Замените источник питания, или замените вентилятор
131
Fanout speed error
Check whether the fan connection is normal, or replace the power supply, or replace the
fan
Ошибка скорости вращения вентилятора на выходе
Проверьте, правильно ли подключен вентилятор, исправен ли он. Замените источник питания, или замените вентилятор
140
Fan speed is too high
Please check the environment temperature
Слишком высокая скорость вращения вентилятора
Пожалуйста, проверьте температуру окружающей среды или проверьте запыленность хэшплат
200
Power probing error, no power found
Detecting power output wiring, updating the latest firmware, or replacing power supply
Ошибка измерения мощности, питание не найдено
Проверьте силовую проводку, обновите до последней версии встроенное программное обеспечение или замена источника питания
201
Power supply and configuration file mismatch
Replace the correct PSU
Несоответствие источника питания и конфигурационного файла
Замените блок питания на оригинальный
203
Power protecting
Please check the environment temperature
Защита по питанию
Пожалуйста, проверьте температуру окружающей среды
204
Power current protecting
Please check the environment temperature
Защита от тока питания
Пожалуйста, проверьте температуру окружающей среды
205
Power current error
Inspection of power supply in power grid
Ошибка тока питания
Проверка электроснабжения в электросети
206
Power input voltage is low
Improve power supply conditions and input voltage
Входное напряжение питания низкое
Проверьте напряжение под нагрузкой. Улучшите условия подключения майнера
207
Power input current protecting
Improve power supply conditions and input voltage
Защита от входного тока питания
Улучшите условия питания и входное напряжение
210
Power error status
Check power failure code
Состояние ошибки питания
Проверьте код сбоя питания
213
Power input voltage and current do not match the power
Replace the PSU
Входное напряжение и ток питания не соответствуют мощности
Проверьте напряжение под нагрузкой. Улучшите условия подключения майнера Замените блок питания
233
Power output over temperature protection
Please check the environment temperature
Защита выходной мощности от перегрева
Пожалуйста, проверьте температуру окружающей среды
234
Power output over temperature protection
Please check the environment temperature
Защита выходной мощности от перегрева
Пожалуйста, проверьте температуру окружающей среды
235
Power output over temperature protection
Please check the environment temperature
Защита выходной мощности от перегрева
Пожалуйста, проверьте температуру окружающей среды
236
Overcurrent Protection of Power Output
Please check the environment temperature, check copper row screw
Защита выходной мощности от перегрузки по току
Пожалуйста, проверьте температуру окружающей среды, проверьте винтовое соединение медной шины питания
237
Overcurrent Protection of Power Output
Please check the environment temperature, check copper row screw
Защита выходной мощности от перегрузки по току
Пожалуйста, проверьте температуру окружающей среды, проверьте винтовое соединение медной шины питания
238
Overcurrent Protection of Power Output
Please check the environment temperature, check copper row screw
Защита выходной мощности от перегрузки по току
Пожалуйста, проверьте температуру окружающей среды, проверьте винтовое соединение медной шины питания
239
Overvoltage Protection of Power Output
Inspection of power supply in power grid
Защита выходной мощности от перенапряжения
Проверка электроснабжения в электросети
240
Low Voltage Protection for Power Output
Inspection of power supply in power grid
Защита выходной мощности от низкого напряжения
Проверка электроснабжения в электросети
241
Power output current imbalance
Replace the power
Дисбаланс выходного тока
Замените питание
243
Over-temperature Protection for Power Input
Please check the environment temperature
Перегрев. Защита вводной мощности
Пожалуйста, проверьте температуру окружающей среды
244
Over-temperature Protection for Power Input
Please check the environment temperature
Перегрев. Защита вводной мощности
Пожалуйста, проверьте температуру окружающей среды
245
Over-temperature Protection for Power Input
Please check the environment temperature
Перегрев. Защита вводной мощности
Пожалуйста, проверьте температуру окружающей среды
246
Overcurrent Protection for Power Input
Please check the environment temperature
Защита от перегрузки по току вводной мощности
Пожалуйста, проверьте температуру окружающей среды
247
Overcurrent Protection for Power Input
Please check the environment temperature
Защита от перегрузки по току вводной мощности
Пожалуйста, проверьте температуру окружающей среды
248
Overvoltage Protection for Power Input
Inspection of input voltage in power grid
Защита от перенапряжения для вводной мощности
Проверьте входное напряжение в электросети
249
Overvoltage Protection for Power Input
Inspection of input voltage in power grid
Защита от перенапряжения для вводной мощности
Проверьте входное напряжение в электросети
250
Undervoltage Protection for Power Input
Inspection of input voltage in power grid
Защита от пониженного напряжения для вводной мощности
Проверьте входное напряжение в электросети
251
Undervoltage Protection for Power Input
Inspection of input voltage in power grid
Защита от пониженного напряжения для потребляемой мощности
Проверьте входное напряжение в электросети
253
Power Fan Error
Replace the PSU
Ошибка вентилятора питания
Замените блок питания или вентилятор замените на аналогичный
254
Power Fan Error
Replace the PSU
Ошибка вентилятора питания
Замените блок питания или вентилятор замените на аналогичный
255
Protection of over power output
Please check the environment temperature
Защита выходной мощности от перегрузки
Пожалуйста, проверьте температуру окружающей среды
256
Protection of over power output
Please check the environment temperature
Защита выходной мощности от перегрузки
Пожалуйста, проверьте температуру окружающей среды
257
Input over current protection of power supply primary side
Try to power off and restart, no effect to replace the power supply
Защита от перегрузки по току на входе первичной стороны источника питания
Попробуйте выключить питание и перезапустить или замените источник питания
263
Power communication warning
Check whether the screws of the control board are locked
Предупреждение об отключении питания
Проверьте, зафиксированы ли винты платы управления
264
Power communication error
Check whether the screws of the control board are locked
Ошибка связи с питанием
Проверьте, зафиксированы ли винты платы управления
267
Power watchdog protection
Contact the technician in time
Защита от отключения питания
Вовремя обратитесь к специалисту
268
Power output over-current protection
Check the ambient temperature, check the copper bar screw
Защита от перегрузки по току на выходной мощности
Пожалуйста, проверьте температуру окружающей среды, проверьте винтовое соединение медной шины питания
269
Power input over-current protection
Improve power supply conditions and input voltage
Защита от перегрузки по току на входе питания
Улучшите условия питания и входное напряжение
270
Power input over-voltage protection
Inspection of input voltage in power grid
Защита от перенапряжения на входе питания
Проверка входного напряжения в электросети
271
Power input under-voltage protection
Inspection of input voltage in power grid
Защита от пониженного напряжения на входе питания
Проверка входного напряжения в электросети
272
Warning of excessive power output of power supply
Please check the environment temperature
Предупреждение о чрезмерной выходной мощности источника питания
Пожалуйста, проверьте температуру окружающей среды
273
Power input power too high warning
Please check the environment temperature
Потребляемая мощность слишком высокая предупреждение
Пожалуйста, проверьте температуру окружающей среды
274
Power fan warning
Check if the power fan is blocked and may need to be replaced
Предупреждение о включении вентилятора
Проверьте, не заблокирован ли вентилятор питания и не нуждается ли он в замене или очистке
275
Power over temperature warning
Please check the environment temperature
Предупреждение о превышении температуры питания
Пожалуйста, проверьте температуру окружающей среды
300
SM0 temperature sensor detection error
Check the connection of the hashboard
Ошибка обнаружения датчика температуры SM0
Проверьте подключение хэш-платы
301
SM1 temperature sensor detection error
Check the connection of the hashboard
Ошибка обнаружения датчика температуры SM1
Проверьте подключение хэш-платы
302
SM2 temperature sensor detection error
Check the connection of the hashboard
Ошибка обнаружения датчика температуры SM2
Проверьте подключение хэш-платы
320
SM0 temperature reading error
Check whether the control board screw is locked properly, check the connection board and the arrangement contact
Ошибка считывания температуры SM0
Проверьте, правильно ли зафиксирован винты платы управления, проверьте соединительную плату и установочный контакт
321
SM1 temperature reading error
Check whether the control board screw is locked properly, check the connection board and the arrangement contact
Ошибка считывания температуры SM1
Проверьте, правильно ли зафиксирован винт платы управления, проверьте соединительную плату и установочный контакт
322
SM2 temperature reading error
Check whether the control board screw is locked properly, check the connection board and the arrangement contact
Ошибка считывания температуры SM2
Проверьте, правильно ли зафиксирован винт платы управления, проверьте соединительную плату и установочный контакт
329
Control board temperature sensor communication error
Replace the power supply
Ошибка связи с датчиком температуры контрольной платы
Замените блок питания
350
SM0 temperature protecting
Please check the environment temperature
Защита от температуры SM0
Пожалуйста, проверьте температуру окружающей среды
351
SM1 temperature protecting
Please check the environment temperature
Защита от перегрева SM1
Пожалуйста, проверьте температуру окружающей среды
352
SM2 temperature protecting
Please check the environment temperature
Защита от температуры SM2
Пожалуйста, проверьте температуру окружающей среды
410
SM0 detect eeprom error
Check adapter board and wiring contact
SM0 обнаружение ошибки eeprom ( памяти)
Проверьте плату адаптера и контакты проводки
411
SM1 detect eeprom error
Check adapter board and wiring contact
SM1 обнаруживает ошибку eeprom
Проверьте плату адаптера и контакты проводки
412
SM2 detect eeprom error
Check adapter board and wiring contact
SM2 обнаруживает ошибку eeprom
Проверьте плату адаптера и контакты проводки
420
SM0 parser eeprom error
Contact the technician in time
Ошибка eeprom анализатора SM0
Вовремя обратитесь к специалисту
421
SM1 parser eeprom error
Contact the technician in time
Ошибка eeprom анализатора SM1
Вовремя обратитесь к специалисту
422
SM2 parser eeprom error
Contact the technician in time
Ошибка eeprom анализатора SM2
Вовремя обратитесь к специалисту
430
SM0 chip bin type error
Contact the technician in time
Ошибка бинарного кода для микросхем SM0
Вовремя обратитесь к специалисту
431
SM1 chip bin type error
Contact the technician in time
Ошибка бинарного кода для микросхем SM1
Вовремя обратитесь к специалисту
432
SM2 chip bin type error
Contact the technician in time
Ошибка бинарного кода для микросхем SM2
Вовремя обратитесь к специалисту
440
SM0 eeprom chip num X error
Contact the technician in time
Ошибка SM0 ошибка внутренней памяти чипа X
Вовремя обратитесь к специалисту
441
SM1 eeprom chip num X error
Contact the technician in time
Ошибка SM1 ошибка внутренней памяти чипа X
Вовремя обратитесь к специалисту
442
SM2 eeprom chip num X error
Contact the technician in time
Ошибка SM2 ошибка внутренней памяти чипа X
Вовремя обратитесь к специалисту
510
SM0 miner type error
The version and type of hashboard are inconsistent, replace the correct hashboard
Ошибка типа майнера SM0
Версия и тип хэш-плату несовместимы, замените на правильную хэш-плату
511
SM1 miner type error
The version and type of hashboard are inconsistent, replace the correct hashboard
Ошибка типа майнера SM1
Версия и тип хэш-плату несовместимы, замените на правильную хэш-плату
512
SM2 miner type error
The version and type of hashboard are inconsistent, replace the correct hashboard
Ошибка типа майнера SM2
Версия и тип хэш-плату несовместимы, замените на правильную хэш-плату
530
SM0 not found
Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded
SM0 не найден
Проверьте подключение и расположение платы адаптера или замените плату управления, проверьте подключение разъема платы адаптера.
531
SM1 not found
Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded
SM1 не найден
Проверьте подключение и расположение платы адаптера или замените плату управления, проверьте подключение разъема платы адаптера..
532
SM2 not found
Check the connection and arrangement of the adapter board, or replace the contro board, check whether the hash board connector is empty welded
SM2 не найден
Проверьте подключение и расположение платы адаптера или замените плату управления, проверьте подключение разъема платы адаптера.
540
SM0 reading chip id error
Check adapter board and wiring contact, Clean the dust on the hashboard
Ошибка считывания идентификатора микросхемы SM0
Проверьте плату адаптера и контакты проводки, Очистите от пыли хэш-плату
541
SM1 reading chip id error
Check adapter board and wiring contact, Clean the dust on the hashboard
Ошибка считывания идентификатора микросхемы SM1
Проверьте плату адаптера и контакты проводки, Очистите от пыли хэш-плату
542
SM2 reading chip id error
Check adapter board and wiring contact, Clean the dust on the hashboard
Ошибка считывания идентификатора микросхемы SM2
Проверьте плату адаптера и контакты проводки, Очистите от пыли хэш-плату
550
SM0 have bad chips
Replacement of bad chips
У SM0 плохие чипы
Замена плохих чипов
551
SM1 have bad chips
Replacement of bad chips
У SM1 плохие чипы
Замена плохих чипов
552
SM2 have bad chips
Replacement of bad chips
У SM2 плохие чипы
Замена плохих чипов
560
SM0 loss balance
Plug in the adapter plate, and then screw in the power connection hashboard again
Баланс потерь SM0
Вставьте в розетку переходную пластину, а затем снова ввинтите разъем подключения питания
561
SM1 loss balance
Plug in the adapter plate, and then screw in the power connection hashboard again
Баланс потерь SM1
Вставьте в розетку переходную пластину, а затем снова ввинтите разъем подключения питания
562
SM2 loss balance
Plug in the adapter plate, and then screw in the power connection hashboard again
Баланс потерь SM2
Вставьте в розетку переходную пластину, а затем снова ввинтите разъем подключения питания
600
Environment temperature is high
Please check the environment temperature
Температура окружающей среды высокая
Пожалуйста, проверьте температуру окружающей среды
610
If the ambient temperature is too high in high performance mode, return to normal mode
Check the ambient temperature, high performance mode needs to be controlled below 30 ℃
Если температура окружающей среды слишком высока в режиме высокой производительности, вернитесь в нормальный режим
Проверьте температуру окружающей среды, необходимо контролировать режим высокой производительности ниже 30 ℃
710
Control board rebooted as exception
Updating the latest firmware.Check whether the control board screw is locked properly
Плата управления перезагружена как исключение
Обновление последней версии прошивки. Проверьте, правильно ли зафиксирован винт платы управления
800
cgminer checksum error
Re-upgrade firmware
ошибка контрольной суммы cgminer
Повторное обновление встроенного ПО
801
system-monitor checksum error
Re-upgrade firmware
ошибка контрольной суммы системного монитора
Повторное обновление встроенного ПО
802
remote-daemon checksum error
Re-upgrade firmware
ошибка контрольной суммы удаленных служебных задач
Повторное обновление встроенного ПО
2010
All pools are disable
Please check the network or pools configure
Все пулы отключены
Пожалуйста, проверьте настройки сети или пулов
2020
Pool0 connect failed
Please check the network or pools configure
Ошибка подключения пулом0
Пожалуйста, проверьте настройки сети или пулов
2021
Pool1 connect failed
Please check the network or pools configure
Сбой соединения с пулом1
Пожалуйста, проверьте настройки сети или пулов
2022
Pool2 connect failed
Please check the network or pools configure
Сбой соединения с пулом2
Пожалуйста, проверьте настройки сети или пулов
2030
High rejection rate of pool
Please check the network or pools configure.Setting of mining currency
Высокий процент отбраковки пула
Пожалуйста, проверьте настройки сети или пулов. Настройка валюты майнинга
2040
The pool does not support the asicboost mode
Check pool configuration
Пул не поддерживает режим asicboost
Проверьте конфигурацию пула
5110
SM0 Frequency Up Timeout
reboot
Время ожидания увеличения частоты SM0
перезагрузка
5111
SM1 Frequency Up Timeout
reboot
Тайм-аут увеличения частоты SM1
перезагрузка
5112
SM2 Frequency Up Timeout
reboot
Время ожидания увеличения частоты SM2
перезагрузка
8410
Software version error (M2x miner with M3x firmware, or M3x with M2x firmware).
Upgrade to the correct firmware version
Ошибка версии программного обеспечения ((M2 x miner с прошивкой M3x или M3x с прошивкой 2x).
Обновите прошивку до правильной версии
PSU
Error code
Reason
processing method
Причина
Способ устранения
0x0001
Input undervoltage
Check the power supply
Входное напряжение низкое
Проверьте источник питания
0x0002
Temperature sampling over temperature protection of power radiator
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Измерение температуры защита от перегрева силового радиатора
Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания
0x0004
Temperature sampling over temperature protection of power radiator
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Измерение температуры защита от перегрева силового радиатора
Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания
0x0008
Over temperature protection of environmental temperature sampling in power supply
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Защита от перегрева при отборе проб температуры окружающей среды в источнике питания
Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания
0x0010
Primary side over current
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Перегрузка по току на первичной стороне
Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания
0x0020
Output undervoltage
Check the power supply
Пониженное выходное напряжение
Проверьте источник питания
0x0040
Output over current (continuous load 320A for more than 2S)
Tighten the copper bar screw again
Перегрузка по току на выходе (непрерывная нагрузка 320A более 2 секунд)
Снова затяните винт на медной шине
0x0080
Primary side over current
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Перегрузка по току на первичной стороне
Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания
0x0100
Single circuit overcurrent(protection point 120a)
Check the PSU
Перегрузка по току в одной цепи (точка защиты 120а)
Проверьте блок питания
0x0200
Single circuit overcurrent(protection point 120a)
Check the PSU
Перегрузка по току в одной цепи (точка защиты 120а)
Проверьте блок питания
0x0400
Single circuit overcurrent(protection point 120a)
Check the PSU
Перегрузка по току в одной цепи (точка защиты 120а)
Проверьте блок питания
0x0800
Fan failure
Replace the PSU
Неисправность вентилятора
Замените блок питания
0x1000
Output over current (continuous load of 310A for more than 5min)
Check the PSU
Перегрузка по току на выходе (непрерывная нагрузка 310 А более 5 мин)
Проверьте блок питания
0x2000
Output over current (continuous load 295A for more than 10min)
Check the PSU
Перегрузка по току на выходе (непрерывная нагрузка 295 А более 10 мин)
Проверьте блок питания
Коды ошибок асик майнера WhatsMiner
0 ErrSucc ОК ОК — обычный
21 ErrNotPlugged 1 или более хеш-плат не обнаружены Сигнал Hashboard PLUG не обнаружен Номер обнаруженной платы питания, если их более одной, разделенные пробелами 1. Проверьте правильность подключения кабеля SPI (по сравнению с обычной машиной) и снова подключите кабель. 2. Замените плату управления. 3. Замените проблемную доску хешрейта (переделайте доску головоломки).
22 ErrPsuI2cFail Аномальная связь по управлению питанием Неправильная связь I2C источника питания — 1. Заменить блок питания. 2. Замените плату управления.
23 ErrEncoreAllFail Все хэш-платы не могут быть включены SPI недоступен для всех плат хешрейта — 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Отремонтируйте всю машину.
24 ErrEncoreFail Некоторые платы не включаются SPI недоступен на некоторых хэш-досках Номер хэшборда, для которого произошел сбой связи по SPI, если их несколько, разделенных пробелами 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Замените проблемную хеш-доску (переделайте доску-головоломку).
25 ErrSetPllFail Не удалось поднять частоту хэш-платы Не удалось поднять частоту хэш-платы Номер хэшборда: частота ошибок 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Замените проблемную хеш-доску (переделайте доску-головоломку).
26 ErrSetVolFail Не удалось установить напряжение Не удалось установить напряжение Номер хэшборда: 1/2 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Заменить проблемную хеш-доску (присоединиться)
27 ErrBistFail Тест чипа BIST не пройден Тест чипа BIST не пройден Номер хэшборда: 1/2 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить проблемную хеш-доску (присоединиться к плате)
28 ErrSpiFail Ненормальная связь платы хешрейта не может быть автоматически восстановлена ??во время работы Ненормальное соединение SPI платы хешрейта не может быть автоматически восстановлено во время работы Номер хэшборда 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Замените проблемную хеш-доску (переделайте доску-головоломку)
29 ErrI2cFail Ненормальная связь по питанию во время работы не может быть восстановлена ??автоматически Связь I2C с ненормальным источником питания не может быть автоматически восстановлена ??во время работы — 1. Заменить блок питания. 2. Замените плату управления.
30 ErrNetwork Подключение к майнинговому пулу прервано Подключение к майнинговому пулу прервано — Если эта проблема возникает на большом количестве или на всех майнинговых машинах с одним и тем же коммутатором: 1. Проверьте правильность настроек пула для майнинга. 2. Проверьте конфигурацию сетевой среды (например, конфигурацию DHCP, конфигурацию DNS, порт и т. Д.). Если проблемы возникают только на одной или нескольких машинах для майнинга: 1. Проверьте правильность настроек пула для майнинга. 2. Проверить подключения к сетевому порту майнера. 3. Замените сетевой кабель на работающую майнинговую машину. 4. Замените плату управления.
31 ErrBadChip Повреждение отдельных микросхем, что приводит к искусственно завышенной вычислительной мощности Повреждение отдельных микросхем, что приводит к искусственно завышенной вычислительной мощности Номер поврежденной микросхемы: номер хеш-платы, если их более одной, разделенные пробелами В ремонт
32 ErrOverheat Hashboard перегрелся Hashboard перегрелся Номер хэшборда 1. Проверьте, вращаются ли передний и задний вентиляторы, если они не вращаются, сначала замените вентиляторы, а затем замените плату управления / блок питания. 2. Убедитесь, что направление ветра спереди и сзади согласовано, согласуется ли оно с другими машинами, если нет, измените направление вентилятора. 3. Если температура воздуха на входе горной машины превышает 40 градусов, необходимо улучшить температурную среду в шахте. 4. Если определенная плата хешрейта часто перегревается, вы можете заменить проблемную плату хешрейта (переделайте головоломку).
33 ErrInvTemp Невозможно прочитать температуру чипа Невозможно прочитать температуру чипа Номер хэшборда 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Замените проблемную хеш-доску (переделайте доску-головоломку).
34 ErrMisPlugged Неправильное подключение кабеля связи платы управления Ненормальное подключение кабеля SPI платы управления Номер хэшборда 1. Проверьте, совместим ли метод (последовательность) подключения кабеля SPI хэш-платы с другими машинами той же модели. 2. Замените плату управления.
35 ErrPsuFail Аномальный источник питания Аномальный источник питания 1. Обратите внимание на то, что если нет явного отклонения от нормы вычислительной мощности всей машины (не отключается плата), то перезагрузить 2. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 3. Заменить блок питания.
36 ErrInvCorenum Некоторые чипы не работают должным образом Количество хороших фишек ненормальное Номер хэшборда: номер чипа 1. Обратите внимание на то, что если нет явного отклонения от нормы вычислительной мощности всей машины (не отключается плата), то перезагрузить 2. Перезапустите майнер, чтобы увидеть, появляется ли по-прежнему та же ошибка. 3. Замените проблемную хеш-плату.
37 ErrInvVidtype Тип платы управления / версия прошивки / количество микросхем не совпадает Тип платы управления / версия прошивки / количество микросхем не совпадает vidtype, minertype, subtype, chipnum После накопления нескольких единиц (> 10) обратитесь в ремонт.
38 ErrBadRearChips Наконец, у некоторых чипов низкая вычислительная мощность. Последние несколько уровней чипов имеют низкую вычислительную мощность В ремонт
39 ErrInvTuneParam Аномальные параметры старения Напряжение начальной частоты старения неверно В ремонт
Errcode | Scope of application | Explanation | Troubleshooting steps |
0 | Whole miner | Normal | Normal |
21 | hashboard | one or more hashboards can’t be detected | 1. check and see whether the SPI cables are firmly and correctly connected (compared the connection of cables with working miners), reconnect the SPI cables, don’t change sequence of connection 2. replace control board with other well functional one 3. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
22 | Whole miner | PSU communication is abnormal | 1. replace PSU with other well functional one 2. replace control board with other well functional one |
23 | Whole miner | All hashboards can’t be powered up | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. whole miner should be returned for repair |
24 | hashboard | one or more hashboards can’t be powered up | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
25 | hashboard | frequency increase of hashboards fails | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check and see whether screws on the PSU side and SPI connection are loose 3. replace PSU with other well functional one 4. replace control board with other well functional one 5. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
26 | hashboard | voltage setting fails | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
27 | hashboard | chip BIST test fails | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
28 | hashboard | abnormal communication of hashboard, it can’t be automatically recovered when running | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
29 | Whole miner | abnormal communication of PSU can’t be automatically recovered when running | 1. replace PSU with other well functional one 2. replace control board with other well functional one |
30 | Whole miner | pool disconnect | If the problem occurs in a large number of miners or all of the mines under the same switch: 1. please first check whether pool setting is correct 2. then check network configuration (such as DHCP configuration, DNS configuration, ports, etc.) If the problem occurs in only one or just a small number of miners under the same switch: 1. please first check whether pool setting is correct 2. then check whether network cable is firmly connected 3. replace network cable with other one from other well working miner 4. replace control board with other well functional one |
31 | hashboard | damage of some individual chip causes inflated high hashrate of the miner | no action should be taken |
32 | hashboard | hashboard overheat | 1. check and see whether both fans are spinning, if not, replace fan with other functional one, if still not, then replace control board or PSU 2. check and see whether wind direction of both fans are the same, whether wind direction are the same with other miners, if not, exchange fans 3. meter the inlet temperature of the miner, if above 40 °C, cooling system of the mining farm should be improved 4. if some hashboard is overheated frequently, that hashboard should be replaced (returned for repair) |
33 | hashboard | chip temperature can’t be read | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
34 | cables of control board is connected incorrectly | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check whether hashboard SPI cables are conneted in the same way (sequence) as other miners of same model 3. replace control board with other well functional one |
|
35 | hashboard | PSU voltage is too low | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2.check and see whether screws on the PSU side and SPI connection is loose 3. replace PSU with other well functional one |
36 | hashboard | working or some chips is abnormal | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. reboot the miner to see whether the same error is given 3. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
37 | Whole miner | mismatch of control board version/firmware version/quantity of chips | if there are more than 10 miners with same error, please contact engineers |
38 | hashboard | low hashrate of last few chips | no action should be taken |
39 | hashboard | testing parameter is abnormal | no action should be taken |
40 | hashboard | PSU load is insufficient | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
41 | hashboard | startup voltage of PSU is too low | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check and see whether screws on the PSU side and SPI connection are loose 3. replace PSU with other well functional one 4. replace control board with other well functional one |
42 | hashboard | implementation of plan B fails when hashboard frequency increases | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check and see whether screws on the PSU side and SPI connection are loose 3. replace PSU with other well functional one 4. replace control board with other well functional one 5. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
Attention: 1. The miner should be powered up again to see whether it is back to normal after every step is taken 2. If the problem is not solve after replacement the part, the part should go back to its original unit 3. Error code and brief description of the problem should be attached to the hashboard that is confirmed defective and that will be returned for repair |
Error
code
Reason Processing method
110 Fanin detect speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
fan
111 Fanout detect speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
fan
130 Fanin speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
fan
131 Fanout speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
fan
140 Fan speed is too high Please check the environment temperature
200
Power probing error, no
power found
Detecting power output wiring, updating the
latest firmware, or replacing power supply
201
Power supply and
configuration file
mismatch
Replace the correct PSU
203 Power protecting Please check the environment temperature
204 Power current protecting Please check the environment temperature
205 Power current error Inspection of power supply in power grid
206 Power input voltage is low
Improve power supply conditions and input
voltage
207
Power input current
protecting
Improve power supply conditions and input
voltage
210 Power error status Check power failure code
213
Power input voltage and
current do not match the
power
Replace the PSU
233
Power output over
temperature protection
Please check the environment temperature
234
Power output over
temperature protection
Please check the environment temperature
235
Power output over
temperature protection
Please check the environment temperature
236
Overcurrent Protection of
Power Output
Please check the environment temperature,
check copper row screw
237
Overcurrent Protection of
Power Output
Please check the environment temperature,
check copper row screw
238
Overcurrent Protection of
Power Output
Please check the environment temperature,
check copper row screw
239
Overvoltage Protection of
Power Output
Inspection of power supply in power grid
240
Low Voltage Protection for
Power Output
Inspection of power supply in power grid
241
Power output current
imbalance
Replace the power
243
Over-temperature
Protection for Power Input
Please check the environment temperature
244
Over-temperature
Protection for Power Input
Please check the environment temperature
245
Over-temperature
Protection for Power Input
Please check the environment temperature
246
Overcurrent Protection for
Power Input
Please check the environment temperature
247
Overcurrent Protection for
Power Input
Please check the environment temperature
248
Overvoltage Protection for
Power Input
Inspection of input voltage in power grid
249
Overvoltage Protection for
Power Input
Inspection of input voltage in power grid
250
Undervoltage Protection
for Power Input
Inspection of input voltage in power grid
251
Undervoltage Protection
for Power Input
Inspection of input voltage in power grid
253 Power Fan Error Replace the PSU
254 Power Fan Error Replace the PSU
255
Protection of over power
output
Please check the environment temperature
256
Protection of over power
output
Please check the environment temperature
257
Input over current
protection of power supply
primary side
Try to power off and restart, no effect to
replace the power supply
263
Power communication
warning
Check whether the screws of the control
board are locked
264 Power communication error
Check whether the screws of the control
board are locked
267 Power watchdog protection Contact the technician in time
268
Power output over-current
protection
Check the ambient temperature, check the
copper bar screw
269
Power input over-current
protection
Improve power supply conditions and input
voltage
270
Power input over-voltage
protection
Inspection of input voltage in power grid
271
Power input under-voltage
protection
Inspection of input voltage in power grid
272
Warning of excessive power
output of power supply
Please check the environment temperature
273
Power input power too high
warning
Please check the environment temperature
274 Power fan warning
Check if the power fan is blocked and may
need to be replaced
275
Power over temperature
warning
Please check the environment temperature
300
SM0 temperature sensor
detection error
Check the connection of the hashboard
301
SM1 temperature sensor
detection error
Check the connection of the hashboard
302
SM2 temperature sensor
detection error
Check the connection of the hashboard
320
SM0 temperature reading
error
Check whether the control board screw is
locked properly, check the connection board
and the arrangement contact
321
SM1 temperature reading
error
Check whether the control board screw is
locked properly, check the connection board
and the arrangement contact
322
SM2 temperature reading
error
Check whether the control board screw is
locked properly, check the connection board
and the arrangement contact
329
Control board temperature
sensor communication error
Replace the power supply
350 SM0 temperature protecting Please check the environment temperature
351 SM1 temperature protecting Please check the environment temperature
352 SM2 temperature protecting Please check the environment temperature
410 SM0 detect eeprom error Check adapter board and wiring contact
411 SM1 detect eeprom error Check adapter board and wiring contact
412 SM2 detect eeprom error Check adapter board and wiring contact
420 SM0 parser eeprom error Contact the technician in time
421 SM1 parser eeprom error Contact the technician in time
422 SM2 parser eeprom error Contact the technician in time
430 SM0 chip bin type error Contact the technician in time
431 SM1 chip bin type error Contact the technician in time
432 SM2 chip bin type error Contact the technician in time
440
SM0 eeprom chip num X
error
Contact the technician in time
441
SM1 eeprom chip num X
error
Contact the technician in time
442
SM2 eeprom chip num X
error
Contact the technician in time
510 SM0 miner type error
The version and type of hashboard are
inconsistent, replace the correct hashboard
511 SM1 miner type error
The version and type of hashboard are
inconsistent, replace the correct hashboard
512 SM2 miner type error
The version and type of hashboard are
inconsistent, replace the correct hashboard
530 SM0 not found
Check the connection and arrangement of the
adapter board, or replace the control
board, check whether the hash board
connector is empty welded
531 SM1 not found
Check the connection and arrangement of the
adapter board, or replace the control
board, check whether the hash board
connector is empty welded
532 SM2 not found
Check the connection and arrangement of the
adapter board, or replace the control
board, check whether the hash board
connector is empty welded
540 SM0 reading chip id error
Check adapter board and wiring contact,
Clean the dust on the hashboard
541 SM1 reading chip id error
Check adapter board and wiring contact,
Clean the dust on the hashboard
542 SM2 reading chip id error
Check adapter board and wiring contact,
Clean the dust on the hashboard
550 SM0 have bad chips Replacement of bad chips
551 SM1 have bad chips Replacement of bad chips
552 SM2 have bad chips Replacement of bad chips
560 SM0 loss balance
Plug in the adapter plate, and then screw
in the power connection hashboard again
561 SM1 loss balance
Plug in the adapter plate, and then screw
in the power connection hashboard again
562 SM2 loss balance
Plug in the adapter plate, and then screw
in the power connection hashboard again
600
Environment temperature is
high
Please check the environment temperature
610
If the ambient temperature
is too high in high
performance mode, return
to normal mode
Check the ambient temperature, high
performance mode needs to be controlled
below 30 ?
710
Control board rebooted as
exception
Updating the latest firmware.Check whether
the control board screw is locked properly
800 cgminer checksum error Re-upgrade firmware
801
system-monitor checksum
error
Re-upgrade firmware
802
remote-daemon checksum
error
Re-upgrade firmware
2010 All pools are disable Please check the network or pools configure
2020 Pool0 connect failed Please check the network or pools configure
2021 Pool1 connect failed Please check the network or pools configure
2022 Pool2 connect failed Please check the network or pools configure
2030
High rejection rate of
pool
Please check the network or pools
configure.Setting of mining currency
2040
The pool does not support
the asicboost mode
Check pool configuration
5110 SM0 Frequency Up Timeout reboot
5111 SM1 Frequency Up Timeout reboot
5112 SM2 Frequency Up Timeout reboot
8410
Software version error
(M2x miner with M3x
firmware, or M3x with M2x
firmware).
Upgrade to the correct firmware version
PSU
Error
code
Reason processing method
0x0001 Input undervoltage Check the power supply
0x0002
Temperature sampling over
temperature protection of
power radiator
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0004
Temperature sampling over
temperature protection of
power radiator
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0008
Over temperature
protection of
environmental temperature
sampling in power supply
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0010 Primary side over current
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0020 Output undervoltage Check the power supply
0x0040
Output over current
(continuous load 320A for
more than 2S)
Tighten the copper bar screw again
0x0080 Primary side over current
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0100
Single circuit overcurrent
(protection point 120a)
Check the PSU
0x0200
Single circuit overcurrent
(protection point 120a)
Check the PSU
0x0400
Single circuit overcurrent
(protection point 120a)
Check the PSU
0x0800 Fan failure Replace the PSU
0x1000
Output over current
(continuous load of 310A
for more than 5min)
Check the PSU
0x2000
Output over current
(continuous load 295A for
more than 10min)
Check the PS
Error code Reason Processing method 110 Fanin detect speed error Check whether the fan connection is normal, or replace the power supply, or replace the fan 111 Fanout detect speed error Check whether the fan connection is normal, or replace the power supply, or replace the fan 130 Fanin speed error Check whether the fan connection is normal, or replace the power supply, or replace the fan 131 Fanout speed error Check whether the fan connection is normal, or replace the power supply, or replace the fan 140 Fan speed is too high Please check the environment temperature 200 Power probing error, no power found Detecting power output wiring, updating the latest firmware, or replacing power supply 201 Power supply and configuration file mismatch Replace the correct PSU 203 Power protecting Please check the environment temperature 204 Power current protecting Please check the environment temperature 205 Power current error Inspection of power supply in power grid 206 Power input voltage is low Improve power supply conditions and input voltage 207 Power input current protecting Improve power supply conditions and input voltage 210 Power error status Check power failure code 213 Power input voltage and current do not match the power Replace the PSU 233 Power output over temperature protection Please check the environment temperature 234 Power output over temperature protection Please check the environment temperature 235 Power output over temperature protection Please check the environment temperature 236 Overcurrent Protection of Power Output Please check the environment temperature, check copper row screw 237 Overcurrent Protection of Power Output Please check the environment temperature, check copper row screw 238 Overcurrent Protection of Power Output Please check the environment temperature, check copper row screw 239 Overvoltage Protection of Power Output Inspection of power supply in power grid 240 Low Voltage Protection for Power Output Inspection of power supply in power grid 241 Power output current imbalance Replace the power 243 Over-temperature Protection for Power Input Please check the environment temperature 244 Over-temperature Protection for Power Input Please check the environment temperature 245 Over-temperature Protection for Power Input Please check the environment temperature 246 Overcurrent Protection for Power Input Please check the environment temperature 247 Overcurrent Protection for Power Input Please check the environment temperature 248 Overvoltage Protection for Power Input Inspection of input voltage in power grid 249 Overvoltage Protection for Power Input Inspection of input voltage in power grid 250 Undervoltage Protection for Power Input Inspection of input voltage in power grid 251 Undervoltage Protection for Power Input Inspection of input voltage in power grid 253 Power Fan Error Replace the PSU 254 Power Fan Error Replace the PSU 255 Protection of over power output Please check the environment temperature 256 Protection of over power output Please check the environment temperature 257 Input over current protection of power supply primary side Try to power off and restart, no effect to replace the power supply 263 Power communication warning Check whether the screws of the control board are locked 264 Power communication error Check whether the screws of the control board are locked 267 Power watchdog protection Contact the technician in time 268 Power output over-current protection Check the ambient temperature, check the copper bar screw 269 Power input over-current protection Improve power supply conditions and input voltage 270 Power input over-voltage protection Inspection of input voltage in power grid 271 Power input under-voltage protection Inspection of input voltage in power grid 272 Warning of excessive power output of power supply Please check the environment temperature 273 Power input power too high warning Please check the environment temperature 274 Power fan warning Check if the power fan is blocked and may need to be replaced 275 Power over temperature warning Please check the environment temperature 300 SM0 temperature sensor detection error Check the connection of the hashboard 301 SM1 temperature sensor detection error Check the connection of the hashboard 302 SM2 temperature sensor detection error Check the connection of the hashboard 320 SM0 temperature reading error Check whether the control board screw is locked properly, check the connection board and the arrangement contact 321 SM1 temperature reading error Check whether the control board screw is locked properly, check the connection board and the arrangement contact 322 SM2 temperature reading error Check whether the control board screw is locked properly, check the connection board and the arrangement contact 329 Control board temperature sensor communication error Replace the power supply 350 SM0 temperature protecting Please check the environment temperature 351 SM1 temperature protecting Please check the environment temperature 352 SM2 temperature protecting Please check the environment temperature 410 SM0 detect eeprom error Check adapter board and wiring contact 411 SM1 detect eeprom error Check adapter board and wiring contact 412 SM2 detect eeprom error Check adapter board and wiring contact 420 SM0 parser eeprom error Contact the technician in time 421 SM1 parser eeprom error Contact the technician in time 422 SM2 parser eeprom error Contact the technician in time 430 SM0 chip bin type error Contact the technician in time 431 SM1 chip bin type error Contact the technician in time 432 SM2 chip bin type error Contact the technician in time 440 SM0 eeprom chip num X error Contact the technician in time 441 SM1 eeprom chip num X error Contact the technician in time 442 SM2 eeprom chip num X error Contact the technician in time 510 SM0 miner type error The version and type of hashboard are inconsistent, replace the correct hashboard 511 SM1 miner type error The version and type of hashboard are inconsistent, replace the correct hashboard 512 SM2 miner type error The version and type of hashboard are inconsistent, replace the correct hashboard 530 SM0 not found Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded 531 SM1 not found Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded 532 SM2 not found Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded 540 SM0 reading chip id error Check adapter board and wiring contact, Clean the dust on the hashboard 541 SM1 reading chip id error Check adapter board and wiring contact, Clean the dust on the hashboard 542 SM2 reading chip id error Check adapter board and wiring contact, Clean the dust on the hashboard 550 SM0 have bad chips Replacement of bad chips 551 SM1 have bad chips Replacement of bad chips 552 SM2 have bad chips Replacement of bad chips 560 SM0 loss balance Plug in the adapter plate, and then screw in the power connection hashboard again 561 SM1 loss balance Plug in the adapter plate, and then screw in the power connection hashboard again 562 SM2 loss balance Plug in the adapter plate, and then screw in the power connection hashboard again 600 Environment temperature is high Please check the environment temperature 610 If the ambient temperature is too high in high performance mode, return to normal mode Check the ambient temperature, high performance mode needs to be controlled below 30 ℃ 710 Control board rebooted as exception Updating the latest firmware.Check whether the control board screw is locked properly 800 cgminer checksum error Re-upgrade firmware 801 system-monitor checksum error Re-upgrade firmware 802 remote-daemon checksum error Re-upgrade firmware 2010 All pools are disable Please check the network or pools configure 2020 Pool0 connect failed Please check the network or pools configure 2021 Pool1 connect failed Please check the network or pools configure 2022 Pool2 connect failed Please check the network or pools configure 2030 High rejection rate of pool Please check the network or pools configure.Setting of mining currency 2040 The pool does not support the asicboost mode Check pool configuration 5110 SM0 Frequency Up Timeout reboot 5111 SM1 Frequency Up Timeout reboot 5112 SM2 Frequency Up Timeout reboot 8410 Software version error (M2x miner with M3x firmware, or M3x with M2x firmware). Upgrade to the correct firmware version PSU Error code Reason processing method 0x0001 Input undervoltage Check the power supply 0x0002 Temperature sampling over temperature protection of power radiator Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0004 Temperature sampling over temperature protection of power radiator Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0008 Over temperature protection of environmental temperature sampling in power supply Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0010 Primary side over current Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0020 Output undervoltage Check the power supply 0x0040 Output over current (continuous load 320A for more than 2S) Tighten the copper bar screw again 0x0080 Primary side over current Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0100 Single circuit overcurrent (protection point 120a) Check the PSU 0x0200 Single circuit overcurrent (protection point 120a) Check the PSU 0x0400 Single circuit overcurrent (protection point 120a) Check the PSU 0x0800 Fan failure Replace the PSU 0x1000 Output over current (continuous load of 310A for more than 5min) Check the PSU 0x2000 Output over current (continuous load 295A for more than 10min) Check the PS
Error code
Reason
Processing method
Причина
Способ устранения
110
Fanin detect speed error
Check whether the fan connection is normal, or replace the power supply, or replace the
fan
Ошибка обнаружения скорости вращения вентилятора на входе
Проверьте, правильно ли подключен вентилятор, исправен ли он. Замените источник питания, или замените вентилятор
111
Fanout detect speed error
Check whether the fan connection is normal, or replace the power supply, or replace the
fan
Ошибка обнаружения скорости вращения вентилятора на выходе
Проверьте, правильно ли подключен вентилятор, исправен ли он. Замените источник питания, или замените вентилятор
130
Fanin speed error
Check whether the fan connection is normal, or replace the power supply, or replace the
fan
Ошибка скорости вращения вентилятора на входе
Проверьте, правильно ли подключен вентилятор, исправен ли он. Замените источник питания, или замените вентилятор
131
Fanout speed error
Check whether the fan connection is normal, or replace the power supply, or replace the
fan
Ошибка скорости вращения вентилятора на выходе
Проверьте, правильно ли подключен вентилятор, исправен ли он. Замените источник питания, или замените вентилятор
140
Fan speed is too high
Please check the environment temperature
Слишком высокая скорость вращения вентилятора
Пожалуйста, проверьте температуру окружающей среды или проверьте запыленность хэшплат
200
Power probing error, no power found
Detecting power output wiring, updating the latest firmware, or replacing power supply
Ошибка измерения мощности, питание не найдено
Проверьте силовую проводку, обновите до последней версии встроенное программное обеспечение или замена источника питания
201
Power supply and configuration file mismatch
Replace the correct PSU
Несоответствие источника питания и конфигурационного файла
Замените блок питания на оригинальный
203
Power protecting
Please check the environment temperature
Защита по питанию
Пожалуйста, проверьте температуру окружающей среды
204
Power current protecting
Please check the environment temperature
Защита от тока питания
Пожалуйста, проверьте температуру окружающей среды
205
Power current error
Inspection of power supply in power grid
Ошибка тока питания
Проверка электроснабжения в электросети
206
Power input voltage is low
Improve power supply conditions and input voltage
Входное напряжение питания низкое
Проверьте напряжение под нагрузкой. Улучшите условия подключения майнера
207
Power input current protecting
Improve power supply conditions and input voltage
Защита от входного тока питания
Улучшите условия питания и входное напряжение
210
Power error status
Check power failure code
Состояние ошибки питания
Проверьте код сбоя питания
213
Power input voltage and current do not match the power
Replace the PSU
Входное напряжение и ток питания не соответствуют мощности
Проверьте напряжение под нагрузкой. Улучшите условия подключения майнера Замените блок питания
233
Power output over temperature protection
Please check the environment temperature
Защита выходной мощности от перегрева
Пожалуйста, проверьте температуру окружающей среды
234
Power output over temperature protection
Please check the environment temperature
Защита выходной мощности от перегрева
Пожалуйста, проверьте температуру окружающей среды
235
Power output over temperature protection
Please check the environment temperature
Защита выходной мощности от перегрева
Пожалуйста, проверьте температуру окружающей среды
236
Overcurrent Protection of Power Output
Please check the environment temperature, check copper row screw
Защита выходной мощности от перегрузки по току
Пожалуйста, проверьте температуру окружающей среды, проверьте винтовое соединение медной шины питания
237
Overcurrent Protection of Power Output
Please check the environment temperature, check copper row screw
Защита выходной мощности от перегрузки по току
Пожалуйста, проверьте температуру окружающей среды, проверьте винтовое соединение медной шины питания
238
Overcurrent Protection of Power Output
Please check the environment temperature, check copper row screw
Защита выходной мощности от перегрузки по току
Пожалуйста, проверьте температуру окружающей среды, проверьте винтовое соединение медной шины питания
239
Overvoltage Protection of Power Output
Inspection of power supply in power grid
Защита выходной мощности от перенапряжения
Проверка электроснабжения в электросети
240
Low Voltage Protection for Power Output
Inspection of power supply in power grid
Защита выходной мощности от низкого напряжения
Проверка электроснабжения в электросети
241
Power output current imbalance
Replace the power
Дисбаланс выходного тока
Замените питание
243
Over-temperature Protection for Power Input
Please check the environment temperature
Перегрев. Защита вводной мощности
Пожалуйста, проверьте температуру окружающей среды
244
Over-temperature Protection for Power Input
Please check the environment temperature
Перегрев. Защита вводной мощности
Пожалуйста, проверьте температуру окружающей среды
245
Over-temperature Protection for Power Input
Please check the environment temperature
Перегрев. Защита вводной мощности
Пожалуйста, проверьте температуру окружающей среды
246
Overcurrent Protection for Power Input
Please check the environment temperature
Защита от перегрузки по току вводной мощности
Пожалуйста, проверьте температуру окружающей среды
247
Overcurrent Protection for Power Input
Please check the environment temperature
Защита от перегрузки по току вводной мощности
Пожалуйста, проверьте температуру окружающей среды
248
Overvoltage Protection for Power Input
Inspection of input voltage in power grid
Защита от перенапряжения для вводной мощности
Проверьте входное напряжение в электросети
249
Overvoltage Protection for Power Input
Inspection of input voltage in power grid
Защита от перенапряжения для вводной мощности
Проверьте входное напряжение в электросети
250
Undervoltage Protection for Power Input
Inspection of input voltage in power grid
Защита от пониженного напряжения для вводной мощности
Проверьте входное напряжение в электросети
251
Undervoltage Protection for Power Input
Inspection of input voltage in power grid
Защита от пониженного напряжения для потребляемой мощности
Проверьте входное напряжение в электросети
253
Power Fan Error
Replace the PSU
Ошибка вентилятора питания
Замените блок питания или вентилятор замените на аналогичный
254
Power Fan Error
Replace the PSU
Ошибка вентилятора питания
Замените блок питания или вентилятор замените на аналогичный
255
Protection of over power output
Please check the environment temperature
Защита выходной мощности от перегрузки
Пожалуйста, проверьте температуру окружающей среды
256
Protection of over power output
Please check the environment temperature
Защита выходной мощности от перегрузки
Пожалуйста, проверьте температуру окружающей среды
257
Input over current protection of power supply primary side
Try to power off and restart, no effect to replace the power supply
Защита от перегрузки по току на входе первичной стороны источника питания
Попробуйте выключить питание и перезапустить или замените источник питания
263
Power communication warning
Check whether the screws of the control board are locked
Предупреждение об отключении питания
Проверьте, зафиксированы ли винты платы управления
264
Power communication error
Check whether the screws of the control board are locked
Ошибка связи с питанием
Проверьте, зафиксированы ли винты платы управления
267
Power watchdog protection
Contact the technician in time
Защита от отключения питания
Вовремя обратитесь к специалисту
268
Power output over-current protection
Check the ambient temperature, check the copper bar screw
Защита от перегрузки по току на выходной мощности
Пожалуйста, проверьте температуру окружающей среды, проверьте винтовое соединение медной шины питания
269
Power input over-current protection
Improve power supply conditions and input voltage
Защита от перегрузки по току на входе питания
Улучшите условия питания и входное напряжение
270
Power input over-voltage protection
Inspection of input voltage in power grid
Защита от перенапряжения на входе питания
Проверка входного напряжения в электросети
271
Power input under-voltage protection
Inspection of input voltage in power grid
Защита от пониженного напряжения на входе питания
Проверка входного напряжения в электросети
272
Warning of excessive power output of power supply
Please check the environment temperature
Предупреждение о чрезмерной выходной мощности источника питания
Пожалуйста, проверьте температуру окружающей среды
273
Power input power too high warning
Please check the environment temperature
Потребляемая мощность слишком высокая предупреждение
Пожалуйста, проверьте температуру окружающей среды
274
Power fan warning
Check if the power fan is blocked and may need to be replaced
Предупреждение о включении вентилятора
Проверьте, не заблокирован ли вентилятор питания и не нуждается ли он в замене или очистке
275
Power over temperature warning
Please check the environment temperature
Предупреждение о превышении температуры питания
Пожалуйста, проверьте температуру окружающей среды
300
SM0 temperature sensor detection error
Check the connection of the hashboard
Ошибка обнаружения датчика температуры SM0
Проверьте подключение хэш-платы
301
SM1 temperature sensor detection error
Check the connection of the hashboard
Ошибка обнаружения датчика температуры SM1
Проверьте подключение хэш-платы
302
SM2 temperature sensor detection error
Check the connection of the hashboard
Ошибка обнаружения датчика температуры SM2
Проверьте подключение хэш-платы
320
SM0 temperature reading error
Check whether the control board screw is locked properly, check the connection board and the arrangement contact
Ошибка считывания температуры SM0
Проверьте, правильно ли зафиксирован винты платы управления, проверьте соединительную плату и установочный контакт
321
SM1 temperature reading error
Check whether the control board screw is locked properly, check the connection board and the arrangement contact
Ошибка считывания температуры SM1
Проверьте, правильно ли зафиксирован винт платы управления, проверьте соединительную плату и установочный контакт
322
SM2 temperature reading error
Check whether the control board screw is locked properly, check the connection board and the arrangement contact
Ошибка считывания температуры SM2
Проверьте, правильно ли зафиксирован винт платы управления, проверьте соединительную плату и установочный контакт
329
Control board temperature sensor communication error
Replace the power supply
Ошибка связи с датчиком температуры контрольной платы
Замените блок питания
350
SM0 temperature protecting
Please check the environment temperature
Защита от температуры SM0
Пожалуйста, проверьте температуру окружающей среды
351
SM1 temperature protecting
Please check the environment temperature
Защита от перегрева SM1
Пожалуйста, проверьте температуру окружающей среды
352
SM2 temperature protecting
Please check the environment temperature
Защита от температуры SM2
Пожалуйста, проверьте температуру окружающей среды
410
SM0 detect eeprom error
Check adapter board and wiring contact
SM0 обнаружение ошибки eeprom ( памяти)
Проверьте плату адаптера и контакты проводки
411
SM1 detect eeprom error
Check adapter board and wiring contact
SM1 обнаруживает ошибку eeprom
Проверьте плату адаптера и контакты проводки
412
SM2 detect eeprom error
Check adapter board and wiring contact
SM2 обнаруживает ошибку eeprom
Проверьте плату адаптера и контакты проводки
420
SM0 parser eeprom error
Contact the technician in time
Ошибка eeprom анализатора SM0
Вовремя обратитесь к специалисту
421
SM1 parser eeprom error
Contact the technician in time
Ошибка eeprom анализатора SM1
Вовремя обратитесь к специалисту
422
SM2 parser eeprom error
Contact the technician in time
Ошибка eeprom анализатора SM2
Вовремя обратитесь к специалисту
430
SM0 chip bin type error
Contact the technician in time
Ошибка бинарного кода для микросхем SM0
Вовремя обратитесь к специалисту
431
SM1 chip bin type error
Contact the technician in time
Ошибка бинарного кода для микросхем SM1
Вовремя обратитесь к специалисту
432
SM2 chip bin type error
Contact the technician in time
Ошибка бинарного кода для микросхем SM2
Вовремя обратитесь к специалисту
440
SM0 eeprom chip num X error
Contact the technician in time
Ошибка SM0 ошибка внутренней памяти чипа X
Вовремя обратитесь к специалисту
441
SM1 eeprom chip num X error
Contact the technician in time
Ошибка SM1 ошибка внутренней памяти чипа X
Вовремя обратитесь к специалисту
442
SM2 eeprom chip num X error
Contact the technician in time
Ошибка SM2 ошибка внутренней памяти чипа X
Вовремя обратитесь к специалисту
510
SM0 miner type error
The version and type of hashboard are inconsistent, replace the correct hashboard
Ошибка типа майнера SM0
Версия и тип хэш-плату несовместимы, замените на правильную хэш-плату
511
SM1 miner type error
The version and type of hashboard are inconsistent, replace the correct hashboard
Ошибка типа майнера SM1
Версия и тип хэш-плату несовместимы, замените на правильную хэш-плату
512
SM2 miner type error
The version and type of hashboard are inconsistent, replace the correct hashboard
Ошибка типа майнера SM2
Версия и тип хэш-плату несовместимы, замените на правильную хэш-плату
530
SM0 not found
Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded
SM0 не найден
Проверьте подключение и расположение платы адаптера или замените плату управления, проверьте подключение разъема платы адаптера.
531
SM1 not found
Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded
SM1 не найден
Проверьте подключение и расположение платы адаптера или замените плату управления, проверьте подключение разъема платы адаптера..
532
SM2 not found
Check the connection and arrangement of the adapter board, or replace the contro board, check whether the hash board connector is empty welded
SM2 не найден
Проверьте подключение и расположение платы адаптера или замените плату управления, проверьте подключение разъема платы адаптера.
540
SM0 reading chip id error
Check adapter board and wiring contact, Clean the dust on the hashboard
Ошибка считывания идентификатора микросхемы SM0
Проверьте плату адаптера и контакты проводки, Очистите от пыли хэш-плату
541
SM1 reading chip id error
Check adapter board and wiring contact, Clean the dust on the hashboard
Ошибка считывания идентификатора микросхемы SM1
Проверьте плату адаптера и контакты проводки, Очистите от пыли хэш-плату
542
SM2 reading chip id error
Check adapter board and wiring contact, Clean the dust on the hashboard
Ошибка считывания идентификатора микросхемы SM2
Проверьте плату адаптера и контакты проводки, Очистите от пыли хэш-плату
550
SM0 have bad chips
Replacement of bad chips
У SM0 плохие чипы
Замена плохих чипов
551
SM1 have bad chips
Replacement of bad chips
У SM1 плохие чипы
Замена плохих чипов
552
SM2 have bad chips
Replacement of bad chips
У SM2 плохие чипы
Замена плохих чипов
560
SM0 loss balance
Plug in the adapter plate, and then screw in the power connection hashboard again
Баланс потерь SM0
Вставьте в розетку переходную пластину, а затем снова ввинтите разъем подключения питания
561
SM1 loss balance
Plug in the adapter plate, and then screw in the power connection hashboard again
Баланс потерь SM1
Вставьте в розетку переходную пластину, а затем снова ввинтите разъем подключения питания
562
SM2 loss balance
Plug in the adapter plate, and then screw in the power connection hashboard again
Баланс потерь SM2
Вставьте в розетку переходную пластину, а затем снова ввинтите разъем подключения питания
600
Environment temperature is high
Please check the environment temperature
Температура окружающей среды высокая
Пожалуйста, проверьте температуру окружающей среды
610
If the ambient temperature is too high in high performance mode, return to normal mode
Check the ambient temperature, high performance mode needs to be controlled below 30 ℃
Если температура окружающей среды слишком высока в режиме высокой производительности, вернитесь в нормальный режим
Проверьте температуру окружающей среды, необходимо контролировать режим высокой производительности ниже 30 ℃
710
Control board rebooted as exception
Updating the latest firmware.Check whether the control board screw is locked properly
Плата управления перезагружена как исключение
Обновление последней версии прошивки. Проверьте, правильно ли зафиксирован винт платы управления
800
cgminer checksum error
Re-upgrade firmware
ошибка контрольной суммы cgminer
Повторное обновление встроенного ПО
801
system-monitor checksum error
Re-upgrade firmware
ошибка контрольной суммы системного монитора
Повторное обновление встроенного ПО
802
remote-daemon checksum error
Re-upgrade firmware
ошибка контрольной суммы удаленных служебных задач
Повторное обновление встроенного ПО
2010
All pools are disable
Please check the network or pools configure
Все пулы отключены
Пожалуйста, проверьте настройки сети или пулов
2020
Pool0 connect failed
Please check the network or pools configure
Ошибка подключения пулом0
Пожалуйста, проверьте настройки сети или пулов
2021
Pool1 connect failed
Please check the network or pools configure
Сбой соединения с пулом1
Пожалуйста, проверьте настройки сети или пулов
2022
Pool2 connect failed
Please check the network or pools configure
Сбой соединения с пулом2
Пожалуйста, проверьте настройки сети или пулов
2030
High rejection rate of pool
Please check the network or pools configure.Setting of mining currency
Высокий процент отбраковки пула
Пожалуйста, проверьте настройки сети или пулов. Настройка валюты майнинга
2040
The pool does not support the asicboost mode
Check pool configuration
Пул не поддерживает режим asicboost
Проверьте конфигурацию пула
5110
SM0 Frequency Up Timeout
reboot
Время ожидания увеличения частоты SM0
перезагрузка
5111
SM1 Frequency Up Timeout
reboot
Тайм-аут увеличения частоты SM1
перезагрузка
5112
SM2 Frequency Up Timeout
reboot
Время ожидания увеличения частоты SM2
перезагрузка
8410
Software version error (M2x miner with M3x firmware, or M3x with M2x firmware).
Upgrade to the correct firmware version
Ошибка версии программного обеспечения ((M2 x miner с прошивкой M3x или M3x с прошивкой 2x).
Обновите прошивку до правильной версии
PSU
Error code
Reason
processing method
Причина
Способ устранения
0x0001
Input undervoltage
Check the power supply
Входное напряжение низкое
Проверьте источник питания
0x0002
Temperature sampling over temperature protection of power radiator
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Измерение температуры защита от перегрева силового радиатора
Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания
0x0004
Temperature sampling over temperature protection of power radiator
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Измерение температуры защита от перегрева силового радиатора
Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания
0x0008
Over temperature protection of environmental temperature sampling in power supply
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Защита от перегрева при отборе проб температуры окружающей среды в источнике питания
Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания
0x0010
Primary side over current
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Перегрузка по току на первичной стороне
Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания
0x0020
Output undervoltage
Check the power supply
Пониженное выходное напряжение
Проверьте источник питания
0x0040
Output over current (continuous load 320A for more than 2S)
Tighten the copper bar screw again
Перегрузка по току на выходе (непрерывная нагрузка 320A более 2 секунд)
Снова затяните винт на медной шине
0x0080
Primary side over current
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply
Перегрузка по току на первичной стороне
Снова включите питание через 10 минут после отключения питания. Если это произойдет снова, замените источник питания
0x0100
Single circuit overcurrent(protection point 120a)
Check the PSU
Перегрузка по току в одной цепи (точка защиты 120а)
Проверьте блок питания
0x0200
Single circuit overcurrent(protection point 120a)
Check the PSU
Перегрузка по току в одной цепи (точка защиты 120а)
Проверьте блок питания
0x0400
Single circuit overcurrent(protection point 120a)
Check the PSU
Перегрузка по току в одной цепи (точка защиты 120а)
Проверьте блок питания
0x0800
Fan failure
Replace the PSU
Неисправность вентилятора
Замените блок питания
0x1000
Output over current (continuous load of 310A for more than 5min)
Check the PSU
Перегрузка по току на выходе (непрерывная нагрузка 310 А более 5 мин)
Проверьте блок питания
0x2000
Output over current (continuous load 295A for more than 10min)
Check the PSU
Перегрузка по току на выходе (непрерывная нагрузка 295 А более 10 мин)
Проверьте блок питания
-
#1
Сорян, в теме не ту ошибку написал. В whatsminer tool выдаёт ошибку 100003. По кодам она описана так — 100003 /antiv/dig/pf_partial.dig Illegal. Но по вебморде ошибок нету. Гуглил — тишина. Может кто в курсе что это значит? Асик работает вполне себе исправно, единственно — задний вентилятор как-то странно короткими волнами меняет скорость. Вжжж-Вжжж-Вжжж.
-
#3
У меня была такая ошибка, при этом аппарат перестал майнить, удаленная перезагрузка не помогала. Пришлось обесточить. После не появлялась
-
#4
У меня была такая ошибка, при этом аппарат перестал майнить, удаленная перезагрузка не помогала. Пришлось обесточить. После не появлялась
Помогла перепрошивка.
Код ошибки | Значение | Соответствующие решения |
---|---|---|
110 | Ошибка скорости детектирования впускного вентилятора | Проверьте, нормально ли подключен вентилятор, или замените источник питания, или замените вентилятор. |
111 | Ошибка скорости обнаружения выходного вентилятора | |
120 | Ошибка скорости входного вентилятора(отклонение 2000+) | |
121 | Ошибка скорости выходного вентилятора(отклонение 2000+) | |
130 | Ошибка скорости вращения впускного вентилятора | |
131 | Ошибка скорости вращения выходного вентилятора | |
140 | Скорость вращения вентилятора слишком высокая | Проверьте температуру окружающей среды |
200 | Ошибка обнаружения питания | Обнаружение выходного кабеля питания, или обновление последней версии микропрограммы, или замена блока питания |
210 | Питание не соответствует файлу конфигурации | Обновление до последней версии программного обеспечения |
202 | Ошибка выходного напряжения питания | Обновление до последней версии программного обеспечения или проверка источника питания |
203 | Защита источника питания | Проверьте температуру окружающей среды |
204 | Защита по току источника питания | |
205 | Ошибка тока питания | Проверка электропитания в электросети |
206 | Низкое входное напряжение питания | Улучшение условий электропитания и входного напряжения |
207 | Входной ток питания защищает | |
210 | Ошибка состояния питания | Проверьте код сбоя питания |
213 | Входное напряжение и ток питания не соответствуют мощности | Замените БП |
216 | Питание остается неизменным в течение длительного времени | |
217 | Ошибка разрешения набора мощности | |
218 | Входное напряжение питания ниже 230 В для режима высокой мощности Увеличьте входное напряжение, замените блок питания | |
233 | Защита выхода питания от перегрева | Проверьте температуру окружающей среды |
234 | Защита выхода питания от перегрева | |
235 | Защита выхода питания от перегрева | |
236 | Защита от перегрузки по току силового выхода | Пожалуйста, проверьте температуру окружающей среды и винт медного провода (рекомендуется использовать защищенную электрическую отвертку) |
237 | Защита от перегрузки по току выхода питания | |
238 | Защита от перегрузки по току выхода питания | |
239 | Защита от перенапряжения на выходе питания | Проверьте питание от сети |
240 | Защита от низкого напряжения на силовом выходе | |
241 | Дисбаланс тока на выходе питания | Замените питание |
243 | Защита от перегрева для входа питания | Проверьте температуру окружающей среды |
244 | Защита от перегрева для входа питания | |
245 | Защита от перегрева для входа питания | |
246 | Защита от перегрузки по току для входа питания | |
247 | Защита от перегрузки по току для входа питания | |
248 | Защита от перенапряжения на входе питания | Проверьте питание от сети |
249 | Защита от перенапряжения для входа питания | |
250 | Защита от пониженного напряжения на входе питания | |
251 | Защита от пониженного напряжения на входе питания | |
253 | Ошибка вентилятора питания | Замените блок питания |
254 | Ошибка вентилятора питания | |
255 | Защита от превышения выходной мощности | Проверьте температуру окружающей среды |
256 | Защита от превышения выходной мощности | |
257 | Защита от перегрузки по току первичной стороны источника питания | Попробуйте выключить и перезапустить питание, замена блока питания не дает эффекта |
263 | Предупреждение о связи по питанию | Проверьте, заблокированы ли винты платы управления |
264 | Ошибка связи по питанию | |
267 | Сторожевая защита питания | Своевременно свяжитесь с техническим специалистом |
268 | Защита от перегрузки по току силового выхода | Проверьте температуру окружающей среды, проверьте винт медной шины |
269 | Защита от перегрузки по току на входе питания | Улучшите условия электропитания и входное напряжение |
270 | Защита от перенапряжения на входе питания | Проверка входного напряжения в электросети |
271 | Защита от пониженного напряжения на входе электросети | |
272 | Предупреждение о чрезмерной мощности источника питания | Проверьте температуру окружающей среды |
273 | Предупреждение о слишком высокой входной мощности источника питания | |
274 | Предупреждение вентилятора питания | Проверьте, не заблокирован ли вентилятор питания и, возможно, его необходимо заменить |
275 | Предупреждение о превышении температуры питания | Проверьте температуру окружающей среды |
0x0001 | Пониженное напряжение на входе | Проверьте блок питания |
0x0002 | Выборка температуры превышение температурной защиты силового радиатора | Снова включите питание через 10 минут после отключения питания. Если это происходит снова, замените блок питания |
0x0004 | Превышение температурной выборки | Температурная защита радиатора питания |
0x0008 | Защита от перегрева при отборе проб температуры окружающей среды в источнике питания | Снова включите питание через 10 минут после отключения питания. Если это происходит снова, замените источник питания |
0x0010 | Перегрузка по току на первичной стороне | Снова включите питание через 10 минут после отключения питания. Если это происходит снова, замените источник питания |
0x0020 | Пониженное напряжение на выходе | Проверьте источник питания |
0x0040 | Превышение выходного тока (непрерывная нагрузка 320A в течение более 2S) | Снова затяните винт медной шины |
0x0080 | Перегрузка по току на первичной стороне | Снова включите питание через 10 минут после отключения питания. Если это происходит снова, замените источник питания |
0x0100 | Перегрузка по току в одной цепи (точка защиты 120a) | Проверьте блок питания |
0x0200 | Одноконтурная перегрузка по току (точка защиты 120a) | |
0x0400 | Одноконтурная перегрузка по току (точка защиты 120a) | |
0x0800 | Отказ вентилятора | Замените блок питания |
0x1000 | Превышение выходного тока (непрерывная нагрузка 310A более 5 минут) | Проверьте БП |
0x2000 | Превышение выходного тока (непрерывная нагрузка 295А в течение более 10 мин) | |
300 | Ошибка обнаружения датчика температуры SM0 | Проверьте подключение хэш-платы |
301 | Ошибка обнаружения датчика температуры SM1 | |
302 | Ошибка обнаружения датчика температуры SM2 | |
320 | Ошибка связи с датчиком температуры платы SM0 | Проверьте, заблокированы ли винты панели управления, проверьте переходную пластину и контакты кабеля |
321 | Ошибка связи с датчиком температуры платы SM1 | |
322 | Ошибка связи с датчиком температуры платы SM2 | |
329 | Температура платы управления ошибка связи с датчиком | Замените источник питания |
350 | Защита от перегрева SM0 | Проверьте температуру окружающей среды (рекомендуется использовать инфракрасный термометр GS320). |
351 | SM1 защита от перегрева | |
352 | SM2 защита от перегрева | |
360 | Температура хэш-платы перегревается | |
410 | SMO обнаружило ошибку eeprom | Проверьте переходную пластину и контакт кабеля |
411 | SM1 обнаружило ошибку eeprom | |
412 | SM2 обнаружило ошибку eeprom | |
420 | SM0 ошибка синтаксического анализатора eeprom | Обновить прошивку |
421 | SM1 ошибка синтаксического анализатора eeprom | |
422 | M2 ошибка eeprom синтаксического анализатора | |
430 | Ошибка типа бина микросхемы SM0 | |
431 | Ошибка типа бина микросхемы SM1 | |
432 | Ошибка типа буфера микросхемы SM2 | |
440 | Ошибка SM0 eeprom chip num X | |
441 | Ошибка SM1 eeprom chip num X | |
442 | SM2 номер микросхемы eeprom X ошибка | |
450 | SM0 eeprom xfer error | Проверьте плату адаптера и контакты проводки.Обновите прошивку |
451 | SM1 eeprom xfer error | |
452 | SM2 eeprom xfer error | |
510 | SM0 ошибка типа майнера | Версия и тип хэшборда несовместимы, замените правильный хэшборд |
511 | SM1 ошибка типа майнера | |
512 | Ошибка типа майнера SM2 | |
520 | Ошибка типа бина SM0 | Если тип чипа хэш-платы несовместим, замените правильную хэш-плату |
521 | Ошибка типа бина SM1 | |
522 | Ошибка типа бина SM2 | |
530 | Плата SM0 не обнаружена | Проверьте проводку платы адаптера и кабель, или замените плату управления, чтобы проверить, припаян ли разъем хэш-платы. |
531 | Плата SM1 не обнаружена | |
532 | Плата SM2 не обнаружена | |
540 | Количество микросхем SM0 неполное | Проверьте переходную пластину и контакт кабеля |
541 | Количество микросхем SM1 неполное | |
542 | Количество микросхем SM2 неполное | |
550 | SM0 имеет плохие чипы | Замените плохую микросхему в позиции печати |
551 | SM1 имеет плохие чипы | |
552 | SM2 имеет плохие чипы | |
560 | SM0 потеря баланса | Подключите переходную пластину, а затем снова прикрутите хэш-плату для подключения питания |
561 | SM1 потеря баланса | |
562 | SM2 потеря баланса | |
590 | Частота SM0 слишком низкая | Замените хэш-плату и поместите вместе хэш-платы, которые сообщили об одной и той же ошибке |
591 | Частота SM1 слишком низкая | |
592 | Частота SM2 слишком низкая | |
600 | Слишком высокая температура окружающей среды | Проверьте температуру окружающей среды |
610 | Если температура окружающей среды слишком высока в режиме высокой производительности, вернитесь в нормальный режим | Проверьте температуру окружающей среды, в режиме высокой производительности должна быть ниже 30 ℃. |
701 | На плате управления отсутствует микросхема поддержки | Обновление соответствующего типа микропрограммы |
710 | Ошибка платы управления | Обновите до последней версии прошивки |
712 | Плата управления перезагрузилась как исключение | Обновление последней версии прошивки. Проверьте, правильно ли зафиксирован винт платы управления |
800 | Ошибка контрольной суммы cgminer | Обновление микропрограммы |
801 | Ошибка контрольной суммы системного монитора | |
802 | Ошибка контрольной суммы системного монитора | |
2000 | Не настроена информация о пуле | Проверьте конфигурацию пула |
2010 | Все подключения к пулам майнинга не удались | Проверьте настройки сети или пулов майнинга |
2020 | Не удалось установить соединение с пулом майнинга | |
2021 | Не удалось установить соединение с пулом майнинга | |
2022 | Не удалось установить соединение с пулом майнинга | |
2030 | Скорость повторного срабатывания пула майнинга слишком высока | Проверьте настройки сети или пула майнинга, а также настройки майнинга криптовалюты |
2040 | Пул не поддерживает режим asicboost | Проверьте конфигурацию пула |
2310 | Хэшрейт слишком низкий | Проверьте входное напряжение, сетевое окружение и температуру окружающей среды. |
2320 | Скорость хэширования слишком низкая | |
2340 | Потеря хэшрейта слишком высока | |
2350 | Потеря скорости хэширования слишком высока | |
5070 | Скорость потока воды SM0 ненормальная | Проверьте, нормальный ли поток воды |
5071 | SM1 Скорость течения воды ненормальная | |
5072 | SM2 Скорость потока воды ненормальная | |
5110 | SM0 Таймаут повышения частоты | Перезагрузите |
5111 | SM1 Таймаут повышения частоты | |
5112 | SM2 Таймаут повышения частоты | |
8410 | Ошибка версии программного обеспечения (miner M2x с прошивкой M3x или M3x с прошивкой M2x) | Обновление до правильной версии прошивки |
100001 | /antiv/signature illegal | Обновление до последней версии микропрограммы или запись карты |
100002 | /antiv/dig/initd.dig illegal | Обновление до последней версии микропрограммы или запись карты |
100003 | /antiv/dig/pf_partial.dig illegal | Обновление до последней версии микропрограммы или запись карты |
Attached is the list of Whatsminer M20s, Whatsminer M30s series error code description for your reference.
Error code | Reason | Processing Method |
110 | Fanin detect speed error | Check whether the fan connection is normal, or replace the power supply, or replace the fan |
111 | Fanout detect speed error | Check whether the fan connection is normal, or replace the power supply, or replace the fan |
120 | Fanin speed error(Deviation 2000+) | Check whether the fan connection is normal, or replace the power supply, or replace the fan |
121 | Fanout speed error(Deviation 2000+) | Check whether the fan connection is normal, or replace the power supply, or replace the fan |
130 | Fanin speed error(Deviation 3000+) | Check whether the fan connection is normal, or replace the power supply, or replace the fan |
131 | Fanout speed error(Deviation 3000+) | Check whether the fan connection is normal, or replace the power supply, or replace the fan |
140 | Fan speed is too high | Please check the environment temperature |
200 | Power probing error, no power found | Detecting power output wiring, updating the latest firmware, or replacing power supply |
201 | Power supply and configuration file mismatch | Replace the correct power supply |
202 | Power output voltage error | Upgrade the latest firmware or check the power supply |
203 | Power protecting | Please check the environment temperature |
204 | Power current protecting | Please check the environment temperature |
205 | Power current error | Inspection of power supply in power grid |
206 | Power input voltage is low | Improve power supply conditions and input voltage |
207 | Power input current protecting | Improve power supply conditions and input voltage |
210 | Power error status | Check power failure code |
213 | Power input voltage and current do not match the power | Replace the power |
216 | Power remained unchanged for a long time | Replace the power |
217 | Power set enable error | Replace the power |
218 | Power input voltage is lower than 230V for high power mode | Increase input voltage,replace power supply |
233 | Power output over temperature protection | Please check the environment temperature |
234 | Power output over temperature protection | Please check the environment temperature |
235 | Power output over temperature protection | Please check the environment temperature |
236 | Overcurrent Protection of Power Output | Please check the environment temperature,check copper row screw |
237 | Overcurrent Protection of Power Output | Please check the environment temperature,check copper row screw |
238 | Overcurrent Protection of Power Output | Please check the environment temperature,check copper row screw |
239 | Overvoltage Protection of Power Output | Inspection of power supply in power grid |
240 | Low Voltage Protection for Power Output | Inspection of power supply in power grid |
241 | Power output current imbalance | Replace the power |
243 | Over-temperature Protection for Power Input | Please check the environment temperature |
244 | Over-temperature Protection for Power Input | Please check the environment temperature |
245 | Over-temperature Protection for Power Input | Please check the environment temperature |
246 | Overcurrent Protection for Power Input | Please check the environment temperature |
247 | Overcurrent Protection for Power Input | Please check the environment temperature |
248 | Overvoltage Protection for Power Input | Inspection of power supply in power grid |
249 | Overvoltage Protection for Power Input | Inspection of power supply in power grid |
250 | Undervoltage Protection for Power Input | Inspection of power supply in power grid |
251 | Undervoltage Protection for Power Input | Inspection of power supply in power grid |
253 | Power Fan Error | Replacing power |
254 | Power Fan Error | Replacing power |
255 | Protection of over power output | Please check the environment temperature |
256 | Protection of over power output | Please check the environment temperature |
257 | Input over current protection of power supply primary side | Try to power off and restart, no effect to replace the power supply |
263 | Power communication warning | Check whether the screws of the control board are locked |
264 | Power communication error | Check whether the screws of the control board are locked |
267 | Power watchdog protection | Contact the technician in time |
268 | Power output over-current protection | Check the ambient temperature, check the copper bar screw |
269 | Power input over-current protection | Improve power supply conditions and input voltage |
270 | Power input over-voltage protection | Inspection of power supply in power grid |
271 | Power input under-voltage protection | Inspection of power supply in power grid |
272 | Warning of excessive power output of power supply | Please check the environment temperature |
273 | Power input power too high warning | Please check the environment temperature |
274 | Power fan warning | Check if the power fan is blocked and may need to be replaced |
275 | Power over temperature warning | Please check the environment temperature |
300 | SM0 temperature sensor detection error | Check the connection of the hashboard |
301 | SM1 temperature sensor detection error | Check the connection of the hashboard |
302 | SM2 temperature sensor detection error | Check the connection of the hashboard |
320 | SM0 temperature reading error | Check whether the control board screw is locked properly, check the connection board and the arrangement contact |
321 | SM1 temperature reading error | Check whether the control board screw is locked properly, check the connection board and the arrangement contact |
322 | SM2 temperature reading error | Check whether the control board screw is locked properly, check the connection board and the arrangement contact |
329 | Control board temperature sensor communication error | Replace the power supply |
350 | SM0 temperature protecting | Please check the environment temperature |
351 | SM1 temperature protecting | Please check the environment temperature |
352 | SM2 temperature protecting | Please check the environment temperature |
360 | The temperature of the hashboard is overheating | Please check the environment temperature |
410 | SM0 detect eeprom error | Check adapter board and wiring contact |
411 | SM1 detect eeprom error | Check adapter board and wiring contact |
412 | SM2 detect eeprom error | Check adapter board and wiring contact |
420 | SM0 parser eeprom error | Upgrade firmware |
421 | SM1 parser eeprom error | Upgrade firmware |
422 | SM2 parser eeprom error | Upgrade firmware |
430 | SM0 chip bin type error | Upgrade firmware |
431 | SM1 chip bin type error | Upgrade firmware |
432 | SM2 chip bin type error | Upgrade firmware |
440 | SM0 eeprom chip num X error | Upgrade firmware |
441 | SM1 eeprom chip num X error | Upgrade firmware |
442 | SM2 eeprom chip num X error | Upgrade firmware |
450 | SM0 eeprom xfer error | Check adapter board and wiring contact.Upgrade firmware |
451 | SM1 eeprom xfer error | Check adapter board and wiring contact.Upgrade firmware |
452 | SM2 eeprom xfer error | Check adapter board and wiring contact.Upgrade firmware |
510 | SM0 miner type error | The version and type of hashboard are inconsistent, replace the correct hashboard |
511 | SM1 miner type error | The version and type of hashboard are inconsistent, replace the correct hashboard |
512 | SM2 miner type error | The version and type of hashboard are inconsistent, replace the correct hashboard |
530 | SM0 not found | Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded |
520 | SM0 bin type error | The chip type of the hashrate board is inconsistent, replace the correct hashrate board |
521 | SM1 bin type error | The chip type of the hashrate board is inconsistent, replace the correct hashrate board |
522 | SM2 bin type error | The chip type of the hashrate board is inconsistent, replace the correct hashrate board |
531 | SM1 not found | Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded |
532 | SM2 not found | Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded |
540 | SM0 reading chip id error | Check adapter board and wiring contact,Clean the dust on the hashboard |
541 | SM1 reading chip id error | Check adapter board and wiring contact,Clean the dust on the hashboard |
542 | SM2 reading chip id error | Check adapter board and wiring contact,Clean the dust on the hashboard |
550 | SM0 have bad chips | Replacement of bad chips |
551 | SM1 have bad chips | Replacement of bad chips |
552 | SM2 have bad chips | Replacement of bad chips |
560 | SM0 loss balance | Plug in the adapter plate, and then screw in the power connection hashboard again |
561 | SM1 loss balance | Plug in the adapter plate, and then screw in the power connection hashboard again |
562 | SM2 loss balance | Plug in the adapter plate, and then screw in the power connection hashboard again |
600 | Environment temperature is high | Please check the environment temperature |
610 | If the ambient temperature is too high in high performance mode, return to normal mode | Check the ambient temperature, high performance mode needs to be controlled below 30 ℃ |
701 | Control board no support chip | Upgrade the corresponding type of firmware |
710 | Control board rebooted as exception | Updating the latest firmware.Check whether the control board screw is locked properly |
712 | Control board rebooted as exception | Updating the latest firmware.Check whether the control board screw is locked properly |
800 | Cgminer checksum error | Re upgrade firmware |
801 | System-monitor checksum error | Re upgrade firmware |
802 | Remote-daemon checksum error | Re upgrade firmware |
810 | Air to liquid PCBSN does not match | Re upgrade the liquid cooling firmware |
2000 | No pool information configured | Check pool configuration |
2010 | All pools are disable | Please check the network or pools configure |
2020 | Pool0 connect failed | Please check the network or pools configure |
2021 | Pool1 connect failed | Please check the network or pools configure |
2022 | Pool2 connect failed | Please check the network or pools configure |
2030 | High rejection rate of pool | Please check the network or pools configure.Setting of mining currency |
2040 | The pool does not support the asicboost mode | Check pool configuration |
2310 | Hash rate is too low | Check input voltage, network environment, and ambient temperature |
2320 | Hash rate is too low | Check input voltage, network environment, and ambient temperature |
2340 | The loss of hash rate is too high | Check input voltage, network environment, and ambient temperature |
2350 | The loss of hash rate is too high | Check input voltage, network environment, and ambient temperature |
5110 | SM0 Frequency Up Timeout | Reboot |
5111 | SM1 Frequency Up Timeout | Reboot |
5112 | SM2 Frequency Up Timeout | Reboot |
5070 | SM0 water velocity is abnormal | Check if the water flow is normal |
5071 | SM1 water velocity is abnormal | Check if the water flow is normal |
5072 | SM2 water velocity is abnormal | Check if the water flow is normal |
8000 | Whatsminertool version is too low | Use the latest Whatsminertool version |
8410 | Software version error (M2x miner with M3x firmware, or M3x with M2x firmware). | Upgrade to the correct firmware version |
100001 | /antiv/signature Illegal | Upgrade the latest firmware or burn the card |
100002 | /antiv/dig/initd.dig Illegal | Upgrade the latest firmware or burn the card |
100003 | /antiv/dig/pf_partial.dig Illegal | Upgrade the latest firmware or burn the card |
PSU Error code | Reason | Processing Method |
0x0001 | Input voltage is too low,need improvement | Check the power supply |
0x0002 | Temperature sampling over temperature protection of power radiator | Power on again after 10 minutes of power failure. If it occurs again, replace the power supply |
0x0004 | Temperature sampling over temperature protection of power radiator | Power on again after 10 minutes of power failure. If it occurs again, replace the power supply |
0x0008 | Over temperature protection of environmental temperature sampling in power supply | Power on again after 10 minutes of power failure. If it occurs again, replace the power supply |
0x0010 | Primary side over current | Power on again after 10 minutes of power failure. If it occurs again, replace the power supply |
0x0020 | Output undervoltage | Check the power supply |
0x0040 | Output over current (continuous load 320A for more than 2S) | Tighten the copper bar screw again |
0x0080 | Primary side over current | Power on again after 10 minutes of power failure. If it occurs again, replace the power supply |
0x0100 | Single circuit overcurrent (protection point 120a) | Check the power supply |
0x0200 | Single circuit overcurrent (protection point 120a) | Check the power supply |
0x0400 | Single circuit overcurrent (protection point 120a) | Check the power supply |
0x0800 | Fan failure | Replace the power supply |
0x1000 | Output over current (continuous load of 310A for more than 5min) | Check the power supply |
0x2000 | Output over current (continuous load 295A for more than 10min) | Check the power supply |