Water circuit priming saeco ошибка

• 28 •

• 28 •

•  Switch the power button to “I” to turn 

the machine on.

Circuit Priming

•  To prime the water circuit, place a 

container under the steam wand 
(Pannarello, if supplied). 

•  Make sure the selector switch is in the  

“ ” position; if this is not the case, set 
it to that position.

•  To turn the machine on simply press the 

“  STAND-BY” button. 

•  The blinking icons (shown to the side) 

warn that the circuit must be primed.

Note: Before starting the 
machine for the first time, 

and after long periods of inactivity, 
prime the water circuit.

•  The “STAND-BY” button blinks.

Blinking

Blinking

Steady on

•  Turn the selector switch clockwise to 

set it to the“

” position. The machine 

starts the automatic priming of the 
circuit by letting out a preset quantity 
of water through the Pannarello.

  Once the circuit has been primed, the 

icon shown in the figure will start 
blinking on the display. 

  Turn the selection knob back to its 

central position “ ”.

• The 

buttons 

“

” and  “

” on the 

control panel blink slowly together 
to show that the machine is warming 
up.

When warm-up is complete, 
the machine performs a rinse 

cycle of the internal circuits.
During this phase the buttons “

”

and “

” blink alternately.

•  When the operations described above 

are completed, the buttons “

” and  

“

” are steady on and the aroma icon 

on the display turns on.

The displayed aroma is the 
factory setting when the 

machine is switched on for the fi rst 
time, or it is the same as the aroma 
that was selected for the last brewed 
coff ee.  

  The machine is then ready to brew 

beverages.

•  To brew coffee, dispense hot water or 

steam, and properly use the machine, ca-
refully follow the instructions provided.

Blinking

Steady on

Blinking

* Переведите кнопку 
включения в положение «I».

* Загорится кнопка 
«STAND-BY».

* Чтобы включить аппарат,
просто нажмите на кнопку
«STAND-BY».
(кнопка включения должна
быть в положении «I»)

* Загорится кнопка 
«STAND-BY».

* Иконки показывают, что
цикл должен быть запущен

Примечание: Перед началом
работы с аппаратом, а также
после долгого периода 
неактивности, запустите
цикл воды.

Запуск цикла

* Чтобы начать цикл воды, 
поместите контейнер под 
трубку подачи воды.

* Чтобы начать цикл воды, 
поместите контейнер под 
трубку подачи воды.

* Вращайте рукоять по часовой
стрелке, установите в позицию      .
Аппарат начнёт цикл, подаст 
установленное кол-во воды.

Когда цикл будет завершён,
иконка на дисплее начнёт
мигать.
Поверните рукоять обратно
в центральную позицию.

* Кнопки          и          на 
панели управления вместе
будут мигать, показывая, что
аппарат в стадии нагрева.

Когда стадии нагрева будет
завершена, аппарат запустит
цикл полоскания.
Во время этой фазы кнопки

                           мигают 
поочерёдно.

* Когда описанные операции
будут завершены, кнопки 

                        будут активны,
также активизируется кнопка 
Aroma.

Отображённая Aroma — 
настройка, которая 
сохраняется с момента 
первого включения 
аппарата или загружается
сохранённая Aroma с 
последнего приготовленного
кофе.

Аппарат готов к
приготовлению напитков

* Чтобы приготовить кофе,
горячую воду или пар, и чтобы
правильно использовать
аппарат, соблюдайте все
указания.

8

Главная   Статьи про кофе   Форум   Новое на сайте

Форумы Модераторы: morbid, latterus Автор Добавил Aerio Пн фев 11 2013, 05:51 Aerio пишет : priming circuit please wait и льется вода мимо заварника Наверх 1234567890? Пн фев 11 2013, 06:43 1234567890? Инструкция -[ссылка]- Вообщем контур водой не может заполнить….не мерзла?? [ Редактирование Пн фев 11 2013, 09:53 ] Наверх Aerio Вт фев 12 2013, 02:02 Aerio В инете нарыл : priming circuit — Первоначальная загрузка водяного контура И т.к. датчик холла не работает вода льется Вопрос где находиться датчик холла ? как до него лучше добраться? Наверх 1234567890? Вт фев 12 2013, 07:36 1234567890? куда вода льется то????с этого надо начинать……пока всю машину не разобрали….. Наверх 1234567890? Вт фев 12 2013, 07:37 1234567890? водомерка ваш датчик холла Наверх Espresso Doktor Сб фев 16 2013, 02:49 Espresso-Doktor ADM написал(а) … В инете нарыл : priming circuit — Первоначальная загрузка водяного контура И т.к. датчик холла не работает вода льется Вопрос где находиться датчик холла ? как до него лучше добраться? Укажите точную модель,и серийный номер, и где купили. Постараюсь помочь Наверх Дмитро Сб фев 16 2013, 03:02 Кофемашина:Dalla Corte Evolution (V2/V3), Dalla Corte Mini (V1,V2,V3) Кофемолка:Mahlkonig K30ES, Mazzer Major, Mazzer Mini Electronic (V1/V2) Ростер:Toper Cafemino Electric / Probat Probatino Gas Др. оборудованиевсякое… Сообщений: 479 Спасибо сказали 21 раз в 20 постах Налейте в бункер воды очень теплой воды и запускайте пока не сбросит ошибку сама, если не захочет — в СЦ вам дорога Наверх Aerio Чт фев 28 2013, 01:26 Aerio Дело оказалось в датчике холла Наверх Powered by Prokofe.Ru Forum System Привет, кто ты? Пользователи: 19056 Новые пользователи: aleksas Стань спонсором прокофе! Получи бейдж в профиль форума «спонсор сайта»! Спасибо!»

Copyright © 2004-2023 Прокофе.ру

The display indicates that the circuit must be primed.

In order to avoid that any water is left in the circuit for a long time, before

starting the machine for the fi rst time, and after long periods of inactivity,

the water circuit needs to be primed. This is because we want to off er you a

perfect and fresh product.

1

Select «START» by pressing the «

automatic priming of the circuit and the bar under the icon shows the

operation progress.

When the process is complete, the machine stops dispensing automa-

tically.

The display might show the machine warm-up icon, as shown in the

fi gure.

2

Place a container under the dispensing spout.

3

Once the warm-up is complete, the machine performs a rinse cycle of

the internal circuits.

During this phase, the icon indicated in the fi gure will be displayed.

4

When the operations described above are complete, the icon is displa-

yed.

The machine is ready to brew beverages.

5

To brew coff ee or dispense hot water or steam, and for a proper use of

the machine, carefully follow the instructions provided.

Note: If the machine is being used for the fi rst time or after a long period of

inactivity, follow the procedures described in the following section.

ENGLISH

» button. The machine starts the

9

• 41 •

English

• 

The machine is performing the rinse cycle.

  Wait until the machine stops the opera-

tion.

• 

The machine needs a descaling cycle.

• 

The machine needs water circuit priming.

Warning Signals

• 

The machine is warming up to brew coff ee 
and dispense hot water or steam.

•  No coff ee beans in the coff ee bean hopper.

  After refi lling the hopper, the cycle can be 

restarted.

• 

Empty the coff ee grounds drawer.

• 

Insert the coff ee grounds drawer.

• 

Fill the water tank.

Alarm Signals

•  Return the hot water / steam knob to its 

correct position.

•  Insert the brew group in the machine.

•  Close the service door.

Steady on

Blinking

Slow Blinking

Steady on

Blinking

Steady on

Steady on

Blinking

Blinking

• 

Brew group overstressed

The coff ee cycle will be interrupted. Perform 
a coff ee cycle again.

• 

OUT OF SERVICE

Turn off  the machine using the power button 
on its back and turn it on again. If the error 
persists, contact the service centre.

Fast Blinking

Blinking

Сигналы 
предупреждения

Сигналы тревоги

Аппарат в стадии разогрева,
готовится к приготовлению 
кофе, горячей воды или пара

Аппарат осуществляет цикл
полоскания.
Подождите, пока аппарат
завершит этот цикл.

Аппарат осуществляет цикл
чистки

Аппарат нуждается в 
циркуляции

Группа приготовления 
перегружена.
Приготовление кофе будет
приостановлено.
Начните цикл приготовления
кофе сначала.

Верните рукоять горячей воды /
пара в правильную позицию
Вставьте группу приготовления
в аппарат
Закройте сервисную дверцу.

Опустошите отсек для кофейных
зёрен.

Вставьте отсек для кофейных
зёрен.

Отсек для кофейных зёрен пуст.
После заполнения отсека цикл
может быть перезапущен.

Заполните резервуар для воды.

СБОЙ В РАБОТЕ
Выключите аппарат, используя
кнопку выключения и затем
включите снова. Если
проблема возникнет снова,
обратитесь в сервисный центр.

21

• 30 •

• 30 •

Red

Orange

Orange

Green

• Turn the machine ON by pressing the

power switch to “I”.

Priming the Water Circuit

• To prime the water circuit, place a

container under the steam/hot water
wand(Pannarello, if supplied).

• The display shows the ON/OFF icon.

• Make sure the ON/OFF button is set to

the “ ” position; if this is not the case,
set it to that position.

• Press the ON/OFF button to turn the

machine on.

• The display indicates that the circuit

must be primed.

Note: Before starting the
machine after long periods

of inactivity, the water circuit must
be primed.

Black

Red

• Turn the selector dial clockwise to set

it to the “

” position. The machine

starts the automatic priming of the
circuit by letting out a preset quantity
of water through the steam/hot water
wand (Pannarello, if supplied). The bar
under the icon shows the operation
progress.

At the end of the priming process,

the display shows an icon (see fig-
ure) indicating that the selection dial
must be brought back to the central
“ ” position.

• The display then shows the machine

warm-up icon, as shown in the fi gure.

When warm-up is complete,
the machine performs a rinse

cycle of the internal circuits.
In this phase, this icon will be dis-
played:

• When the operations described above

are complete, this icon will be dis-
played:

The machine is then ready to brew

beverages.

• To brew coff ee, dispense hot water or

steam, and for a proper use of the ma-
chine, carefully follow the instructions
provided.

If the machine is being used
for the fi rst time or after a

long period of inactivity, follow the
operations described in the follow-
ing section.

Главная   Статьи про кофе   Форум   Новое на сайте

Форумы Модераторы: morbid, latterus Автор Добавил Aerio Пн фев 11 2013, 05:51 Aerio пишет : priming circuit please wait и льется вода мимо заварника Наверх 1234567890? Пн фев 11 2013, 06:43 1234567890? Инструкция -[ссылка]- Вообщем контур водой не может заполнить….не мерзла?? [ Редактирование Пн фев 11 2013, 09:53 ] Наверх Aerio Вт фев 12 2013, 02:02 Aerio В инете нарыл : priming circuit — Первоначальная загрузка водяного контура И т.к. датчик холла не работает вода льется Вопрос где находиться датчик холла ? как до него лучше добраться? Наверх 1234567890? Вт фев 12 2013, 07:36 1234567890? куда вода льется то????с этого надо начинать……пока всю машину не разобрали….. Наверх 1234567890? Вт фев 12 2013, 07:37 1234567890? водомерка ваш датчик холла Наверх Espresso Doktor Сб фев 16 2013, 02:49 Espresso-Doktor ADM написал(а) … В инете нарыл : priming circuit — Первоначальная загрузка водяного контура И т.к. датчик холла не работает вода льется Вопрос где находиться датчик холла ? как до него лучше добраться? Укажите точную модель,и серийный номер, и где купили. Постараюсь помочь Наверх Дмитро Сб фев 16 2013, 03:02 Кофемашина:Dalla Corte Evolution (V2/V3), Dalla Corte Mini (V1,V2,V3) Кофемолка:Mahlkonig K30ES, Mazzer Major, Mazzer Mini Electronic (V1/V2) Ростер:Toper Cafemino Electric / Probat Probatino Gas Др. оборудованиевсякое… Сообщений: 479 Спасибо сказали 21 раз в 20 постах Налейте в бункер воды очень теплой воды и запускайте пока не сбросит ошибку сама, если не захочет — в СЦ вам дорога Наверх Aerio Чт фев 28 2013, 01:26 Aerio Дело оказалось в датчике холла Наверх Powered by Prokofe.Ru Forum System Привет, кто ты? Пользователи: 19118 Новые пользователи: Олег163 Стань спонсором прокофе! Получи бейдж в профиль форума «спонсор сайта»! Спасибо!»

Copyright © 2004-2023 Прокофе.ру

Are you in doubt whether you should try fixing your coffee maker on your own? Of course, it may seem a much easier solution just to throw out the machine or call a professional repairer for help. Yet, you may be surprised to discover that coffee maker troubleshooting is often very simple and doesn’t require much time.

Try the solutions suggested for the Saeco coffee makers in the tables below and see for yourself!

How to reset saeco coffee machine

A Saeco coffee maker has a reset button. To get to it, open the top using a screwdriver. There you will see three thermostats and a button on the middle one. If you hear a metallic sound when pushing the button, there is a problem occurring due to air getting into the heating element. To prevent this, monitor the water supply process and be sure that no air is getting into the system. Take steps to drain air from the system from time to time.

Saeco Odea Giro Plus coffee maker troubleshooting

Problems	Causes	Solutions
The machine does not turn on.	The machine is not connected to the power source.	Connect the machine to the power source.
	The plug has not been plugged into the back of the machine.	Insert the plug into the machine’s power socket.
	Machine in stand-by.	Press the brew button to start the machine.
Coffee is not hot enough.	The cups are cold.	Warm the cups with hot water.
Hot water or steam is not dispensed.	The hole of the steam wand is clogged.	Clean the hole of the steam wand using a pin.
Coffee has little crema.	The coffee blend is unsuitable or coffee is not freshly roasted.	Change coffee blend.
The machine takes a long time to warm up or the amount of water dispensed from the wand is too little.	The machine’s water circuit is obstructed by limescale build-up.	Descale the machine.
The brew group does not come out.	The brew group is out of place.	Turn the machine on. Close the service door. The brew group is automatically placed in the correct position.
	Dregdrawer is inserted.	Remove the dregdrawer first, then the brew group.
The machine grinds the coffee beans but no coffee comes out.	Water tank is empty.	Fill the water tank and prime the water circuit again.
	Brew group is dirty.	Clean the brew group.
	The water circuit is not primed.	Prime the circuit again by dispensing water from the hot water wand.
	Rare event that occurs when the machine is automatically adjusting the dose.	Brew a few coffees as described in the manual.
	The coffee volume knob is turned to the left.	Turn the knob clockwise.
The coffee is too weak.	Rare event that occurs when the machine is automatically adjusting the dose.	Brew a few coffees as described in the manual.
Coffee is brewed slowly	Coffee is too fine.	Adjust the grinder to a coarse grind.
	Circuit is not primed.	Prime the circuit again by dispensing water from the steam wand.
	The brew group is dirty.	Clean the brew group.
Coffee leaks out of the dispensing head.	Dispensing head is clogged.	Clean the dispensing holes with a soft doth.
Brewing does not start.	Coffee bean lid is not dosed properly.	Correctly place the lid on the coffee bean hopper and press it firmly.
The machine grinds the coffee, but coffee does not brew.	The opti-dose adjustment is not at the optimal setting.	Change the opti-dose adjustment.

Saeco Vienna plus sup 018M coffee maker troubleshooting

Problems	Causes	Solutions
The machine does not turn on	The machine is not connected to the power supply.	Connect the machine to the power supply.
	The service door is open.	Close the service door.
Coffee is not hot enough	The cups are cold.	Warm the cups.
No hot water or steam is dispensed	The hole of the steam spout is clogged.	Clean the hole of the steam spout using a pin.
Coffee has little foam	The coffee blend is unsuitable, the coffee is not freshly roasted or the grind is too coarse.	Change coffee blend or adjust the grind. Increase the dose.
The machine takes a long time to warm up or the amount of water dispensed from the spout is too little.	The machine’s circuit is obstructed by limescale.	Descale the machine.
The Brew Group does not come out.	The Brew Group is out of place.	Turn on the machine. Close the service door. The Brew Group is automatically placed in the correct position.
	The grounds drawer is inserted.	Remove the grounds drawer before removing the Brew Group.
Coffee is not brewed	There is no water.	Fill the water tank and prime the circuit again.
	The Brew Group is dirty.	Clean the Brew Group.
	The dose setting is high.	Decrease the dose setting.
	The circuit is not primed.	Prime the circuit again.
Coffee is brewed slowly	The dose setting is high.	Decrease the dose setting.
	The coffee is too fine.	Change coffee blend or adjust the grind. Decrease the dose setting.
	The circuit is not primed.	Prime the circuit again.
	The Brew Group is dirty.	Clean the Brew Group.
Coffee leaks out of the dispensing spout	The dispensing spout is in a wrong position.	Replace the dispensing spout in its correct position.
	The dispensing spout is clogged.	Clean the dispensing spout and its holes.

Saeco V’spresso coffee maker troubleshooting

PROBLEMS	CAUSES	REMEDIES
The brewing cycle does not start	No coffee beans / “Cof Beans Empty”.	Refill bean hopper and press desired coffee button.
	No water / “Fill watertank».	Fill water tank. Make sure float is in position and held in place by the cap. Message will clear.
	Dredge drawer / waste box is full / “Dredgedrawer full”.	Remove waste box while machine is on. Leave out for 5-10 seconds and put back in machine. Message will clear.
	Brew group missing / Brew Unit Miss.	Remove drip tray, waste box and brew group. Put brew group back in machine until securely locks in place, put waste box in, shut service door and put drip tray back in place.
Coffee flows too quickly.	Grind is too coarse.	Adjust the grinder to a finer grind, ex. from 5 to 3. Adjust only while grinder is grinding and only a maximum of 2 settings at a time. It will take 3-4 cups to see results.
	Dose needs to be increased.	Turn doser towards + sign.
Coffee flows too slowly.	Grind is too fine.	Adjust the grinder to a coarser grind, ex. from 5 to 7. Adjust only while grinder is grinding and only a maximum of 2 settings at a time. It will take 34 cups to see results.
	Dose needs to be decreased.	Turn doser towards — sign.
	Filter screen in brew group is clogged.	Clean the filter screen using the key provided.
The machine does not turn on.	The machine is not connected to the power supply.	Move the main switch to ON (T position). Check the plug and the power outlet.
The coffee is not hot enough.	The cups are cold.	Warm up the cups on cup warmer or by dispensing a little hot water into the cup and letting it sit for a few seconds.
	A low temperature has been set.	Set the machine to a higher temperature.
Only water is dispensed when you select “pre-ground coffee’.	No pre-ground coffee has been put into the pre-ground chute.	Select Pre-ground coffee button, put pre-ground coffee into the chute and press the desired coffee button.
	Too much pre-ground coffee put in chute.	Put one level scoop of espresso coffee. Max. 1 cup at a time.
No hot water or steam is dispensed.	The steam wand is dogged.	Clear it with a thin needle or pin. During this operation, the must be closed and the machine must be off. Then run water through steam wand to make sure unclogged.
Reduced amount of coffee, water and steam coming out of the machine; the machine takes longer to heat.	Lime scale / mineral build up in machine.	Descale the machine. If not done for a long period of time, we recommend doing 2 cycles.
Unable to dear Descale message.	Need to reset message.	Go into programming mode, ‘Sign. Decal.» and reset message.
The brew group cannot be removed.	The brew group is out of alignment.	Put waste box in position, close door and put drip tray in position. Switch machine on; the brew group will reset into original position.
Ventilate	Machine needs to be primed.	Dispense 3-4 oz of water through the steam wand.
	Steam wand clogged.	Clear steam wand and prime machine.
	Limescale / mineral build up in machine.	Descale the machine. If not done for a long period of time, we recommend doing 2 cycles.

Saeco EXPRELIA HD8854 coffee maker troubleshooting

Machine actions	Causes	Solutions
The machine does not switch on.	The machine is not connected to the electric network.	Connect the machine to the electric network.
	The power button is set to»0″.	Check that the power button is set to
The drip tray gets filled although no water is drained.	Sometimes water is drained automatically by the machine into the drip tray to manage the rinsing of the circuits and ensure optimum machine performance.	This is seen as normal machine behavior.
Coffee is not hot enough.	The cups are cold.	Preheat the cups with hot water or use the hot water dispenser.
	Beverage temperature in the programming menu is set to low.	Ensure that the temperature is set to Normal or High in the beverage programming menu.
	Cold milk is being added to the coffee.	Cold milk will reduce the temperature of the end product. Therefore please preheat the milk before adding it.
No hot water is dispensed.	The hot water/steam wand is clogged or dirty.	Clean the hot water/steam wand.
		Check if it is clogged by looking into the spout. Use a pin or needle to make a hole through the limestone.
The machine is not filling the cup.	The machine has not been programmed.	Enter the beverage programming menu and adjust the coffee length setting to your liking for every beverage.
Coffee has not enough crema.	The blend is unsuitable, coffee is not freshly roasted or the grind is too coarse.	Change coffee blend
	The coffee beans or the preground coffee are too old.	Ensure that fresh coffee beans or preground coffee are being used.
The milk was not frothed.	The Carafe is dirty or not inserted correctly.	Verify the correct cleaning of the carafe and its insertion.
The machine takes a long time to warm up or the amount of water dispensed from the wand is too little.	The machine circuit is clogged by limescale.	Descale the machine.
The brew group cannot be removed.	The brew group is out of place.	Turn the machine on. Close the service door. The brew group automatically returns to the initial position.
	The coffee grounds drawer is inserted.	Remove the coffee grounds drawer before removing the brew group.
The brew group cannot be inserted.	The brew group is not in rest position.	Ensure that the brew group is in rest position. Both arrows must look towards each other.
	Gear is not in initial position.	Insert the drip tray with the coffee grounds drawer and then close the service door. Turn the machine on. The gear automatically returns to the initial position so the Brew Group can be inserted.
There is a lot of coffee ground under or on the brew group.	The coffee you are using may not be suitable for automatic machines.	It may be necessary to change the type of coffee or the coffee grinder settings.
	The machine is adjusting the grinder due to new coffee beans or preground coffee.	The machine automatically adjusts itself after brewing several cups of coffee to optimize the extraction of the coffee to the compactness of the ground coffee. It may take to up to 2-3 products until the grinder is adjusted. This is not a failure of your machine.
The machine produces coffee grounds that are either too wet or too dry.	The grinder needs to be adjusted.	By adjusting the ceramic coffee grinder, the quality of the puck can be adjusted. When the pucks are too wet, make the grind coarser. When the pucks are too dry, make the grind finer.
The machine grinds the coffee beans but no coffee comes out.	There is no water.	Fill the water tank and prime the circuit.
	The brew group is dirty.	Clean the brew group.
	This might occur when the machine is automatically adjusting the dose.	Brew a few coffees
	The dispensing spout is dirty.	Clean the dispensing spout.
Coffee is too weak.	This might occur when the machine is automatically adjusting the dose.	Brew a few coffees
	The coffee is too coarse.	Change coffee blend or adjust the grind
Coffee is brewed slowly.	The coffee grind is too fine.
	Circuits are clogged.	Perform a descaling cycle.
	The brew group is dirty.	Clean the brew group.
Coffee leaks out of the dispensing spout.	The dispensing spout is clogged.	Clean the dispensing spout and its holes.

Saeco Nina, Aroma, Armonia, Via Veneto, Via Venezia, ABC coffee maker troubleshooting

FAULT	POSSIBLE CAUSES	SOLUTION
The machine does not switch on	No power supply	Check the electrical circuit
The machine does not warm up	The thermostats have intervened The power supply does not reach the boiler	Replace the thermostats (if of the One shot type) If they are manual, reset them If they are automatic, they are reset automatically Check the electrical connections
The pump is very noisy	There is no water in the tank The pump has disengaged from the supports The silicone pipe that carries the water from the tank to the pump is pinched or blocked	Fill the tank Insert the pump into the supports once again Check the water circuit
The coffee is too cold	The filter holder is not inserted for the pre-heating process The cups are cold	Run hot water through the filter holder Pre-heat the cups with hot water
The milk does not froth	The milk is not suitable (powdered or skimmed milk) Dirty nozzle or Cappuccino maker	Use whole milk Carefully clean the nozzle or the cappuccino maker with water
The coffee flows too quickly and does not form the cream	Little coffee in the filter holder Grinding level too coarse There is a missing component in the filter holder	Increase the quantity Use a different mixture Verify that all the components are in place and installed correctly
The coffee does not flow or it flows in drops	Grinding level too fine The coffee is pressed too much in the filter holder Too much coffee in the filter holder Blocked water channels Blocked filter in the filter holder	Use a different mixture Agitate the coffee Reduce the amount of coffee Descale the machine Carefully clean the filter
The coffee does not flow from the edges	The filter holder has been inserted incorrectly into the coffee dispensing unit The upper border of the filter holder is dirty The seal of the boiler is dirty or worn Too much coffee in the filter holder	Insert the filter holder correctly Clean the edges of the fiter holder Clean or replace the seal Reduce the amount of coffee

Saeco XSMALL HD coffee maker troubleshooting

Problem	Possible Cause	Solution
The machine does not turn on.	The machine is not connected to the power source	Connect the machine to the power source.
Coffee is not hot enough.	The cups are cold.	Preheat the cups with hot water.
No hot water or steam is dispensed	The hole of the steam/hot water wand is clogged	Clean the hole of the steam/hot water wand using a pin. Make sure that the machine is off and has cooled down before performing this operation.
	Pannarello is dirty (if supplied).	Clean the Pannarello.
Espresso does not have enough crema	The coffee blend is unsuitable, the coffee is not freshly roasted or the grind is too coarse.	Change coffee blend or adjust the ceramic coffee grinder
The machine takes a long time to warm up or the amount of water dispensed from the hot steam/hot water wand is too small.	The machine water circuit is obstructed by limescale build-up.	Descale the machine
The brew group cannot be removed.	The brew group is out of place.	Turn on the machine. Close the service door. The brew group automatically returns to the correct position.
	The coffee grounds drawer is inserted.	Remove the coffee grounds drawer before removing the brew group.
The brew group cannot be inserted.	The brew group is not in the off position.	Make sure that the brew group in the off position.
	The gearbox is not in the correct position.	Insert the drip tray and the coffee grounds drawer. Close the service door. Turn on the machine without inserting the brew group. The gearbox returns to the correct position. Turn off the machine and reinsert the brew group.
The descaling cycle cannot be finished.	Most probably you have used not enough water for rinsing.	Unplug the power cord and follow the instructions described in the sector » Interruption of the descaling cycle» (Look under the table)
The machine grinds the coffee beans but no coffee is brewed.	1) The brew group is dirty. 2) The water circuit is not primed. 3) This might occur when the ma- chine is automatically adjusting the dose. 4) The coffee dispensing spout is dirty.	1) Clean the brew group. 2) Fill the water tank with fresh water and dispense hot water. 3) Brew a few cups of espresso coffee. (Coffee is a natural product and its characteristics may change according to its origin, blend and roast. The machine is equipped with a self-adjusting system that allows the use of all types of coff ee beans available on the market except for raw, caramelized and fl avoured coff ee beans. The machine automatically adjusts itself after brewing a certain number of cups of coff ee to optimise the extraction.) 4) Clean the coffee dispensing spout.
The coffee is too weak	1) This might occur when the machine is automatically adjusting the dose. 2) The ceramic coffee grinder is set to a coarse grind.	1) Brew a few cups of espresso coffee. (Coffee is a natural product and its characteristics may change according to its origin, blend and roast. The machine is equipped with a self-adjusting system that allows the use of all types of coff ee beans available on the market except for raw, caramelized and fl avoured coff ee beans. The machine automatically adjusts itself after brewing a certain number of cups of coff ee to optimise the extraction.) 2) Adjust the ceramic coffee grinder to a finer setting.
Coffee is brewed slowly	1) The coffee grind is too fine. 2) The water circuit is not primed. 3) The brew group is dirty.	1) Change coffee blend or adjust the grind setting. 2) Fill the water tank with fresh water and dispense hot water. 3) Clean the brew group.
The drip tray gets filled although no water is drained.	Water is drained automatically by the machine into the drip tray to manage the rinsing of the circuits	This is a standard operating procedure.

View details: Interruption of the descaling cycle

• Turn the machine ON by pressing the

power switch to «I».

• The display shows the ON/OFF icon.

Black

• Make sure the ON/OFF button is set to

the » » position; if this is not the case,

set it to that position.

• Press the ON/OFF button to turn the

machine on.

• The display indicates that the circuit

must be primed.

Red

Note: Before starting the

machine after long periods

of inactivity, the water circuit must

be primed.

• 6 •

• 6 •

• To prime the water circuit, place a

container under the steam/hot water

wand(Pannarello, if supplied).

• Turn the selector dial clockwise to set

it to the «

starts the automatic priming of the

circuit by letting out a preset quantity

of water through the steam/hot water

wand (Pannarello, if supplied). The bar

under the icon shows the operation

progress.

At the end of the priming process,

the display shows an icon (see fig-

ure) indicating that the selection dial

must be brought back to the central

» » position.

Red

• The display then shows the machine

warm-up icon, as shown in the fi gure.

Orange

When warm-up is complete,

the machine performs a rinse

cycle of the internal circuits.

In this phase, this icon will be dis-

Orange

played:

• When the operations described above

are complete, this icon will be dis-

played:

The machine is then ready to brew

Green

beverages.

• To brew coff ee, dispense hot water or

steam, and for a proper use of the ma-

chine, carefully follow the instructions

provided.

If the machine is being used

for the fi rst time or after a

long period of inactivity, follow the

operations described in the follow-

ing section.

» position. The machine

• 41 •

English

• 

The machine is performing the rinse cycle.

  Wait until the machine stops the opera-

tion.

• 

The machine needs a descaling cycle.

• 

The machine needs water circuit priming.

Warning Signals

• 

The machine is warming up to brew coff ee 
and dispense hot water or steam.

•  No coff ee beans in the coff ee bean hopper.

  After refi lling the hopper, the cycle can be 

restarted.

• 

Empty the coff ee grounds drawer.

• 

Insert the coff ee grounds drawer.

• 

Fill the water tank.

Alarm Signals

•  Return the hot water / steam knob to its 

correct position.

•  Insert the brew group in the machine.

•  Close the service door.

Steady on

Blinking

Slow Blinking

Steady on

Blinking

Steady on

Steady on

Blinking

Blinking

• 

Brew group overstressed

The coff ee cycle will be interrupted. Perform 
a coff ee cycle again.

• 

OUT OF SERVICE

Turn off  the machine using the power button 
on its back and turn it on again. If the error 
persists, contact the service centre.

Fast Blinking

Blinking

Сигналы 
предупреждения

Сигналы тревоги

Аппарат в стадии разогрева,
готовится к приготовлению 
кофе, горячей воды или пара

Аппарат осуществляет цикл
полоскания.
Подождите, пока аппарат
завершит этот цикл.

Аппарат осуществляет цикл
чистки

Аппарат нуждается в 
циркуляции

Группа приготовления 
перегружена.
Приготовление кофе будет
приостановлено.
Начните цикл приготовления
кофе сначала.

Верните рукоять горячей воды /
пара в правильную позицию
Вставьте группу приготовления
в аппарат
Закройте сервисную дверцу.

Опустошите отсек для кофейных
зёрен.

Вставьте отсек для кофейных
зёрен.

Отсек для кофейных зёрен пуст.
После заполнения отсека цикл
может быть перезапущен.

Заполните резервуар для воды.

СБОЙ В РАБОТЕ
Выключите аппарат, используя
кнопку выключения и затем
включите снова. Если
проблема возникнет снова,
обратитесь в сервисный центр.

21