Vsftpd listen yes ошибка

localadmin@it-1:~$ sudo service vsftpd status
● vsftpd.service - vsftpd FTP server
   Loaded: loaded (/lib/systemd/system/vsftpd.service; enabled; vendor preset: enabled)
   Active: failed (Result: exit-code) since Пт 2016-09-09 10:40:30 KRAT; 4s ago
  Process: 5971 ExecStart=/usr/sbin/vsftpd /etc/vsftpd.conf (code=exited, status=2)
  Process: 5967 ExecStartPre=/bin/mkdir -p /var/run/vsftpd/empty (code=exited, status=0/SUCCESS)
 Main PID: 5971 (code=exited, status=2)

localadmin@it-1:~$ ps -aux|grep ftp
localad+  6444  0.0  0.0  22960  1088 pts/0    S+   11:20   0:00 grep --color=auto ftp

localadmin@it-1:~$ nmap localhost 

Starting Nmap 7.01 ( https://nmap.org ) at 2016-09-09 11:20 KRAT
Nmap scan report for localhost (127.0.0.1)
Host is up (0.000099s latency).
Not shown: 996 closed ports
PORT    STATE SERVICE
22/tcp  open  ssh
25/tcp  open  smtp
139/tcp open  netbios-ssn
445/tcp open  microsoft-ds

Nmap done: 1 IP address (1 host up) scanned in 0.07 seconds
localadmin@it-1:~$ 

localadmin@it-1:~$ cat /etc/vsftpd.conf
# Example config file /etc/vsftpd.conf
#
# The default compiled in settings are fairly paranoid. This sample file
# loosens things up a bit, to make the ftp daemon more usable.
# Please see vsftpd.conf.5 for all compiled in defaults.
#
# READ THIS: This example file is NOT an exhaustive list of vsftpd options.
# Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's
# capabilities.
#
#
# Run standalone?  vsftpd can run either from an inetd or as a standalone
# daemon started from an initscript.
listen=YES
#
# This directive enables listening on IPv6 sockets. By default, listening
# on the IPv6 "any" address (::) will accept connections from both IPv6
# and IPv4 clients. It is not necessary to listen on *both* IPv4 and IPv6
# sockets. If you want that (perhaps because you want to listen on specific
# addresses) then you must run two copies of vsftpd with two configuration
# files.
listen_ipv6=YES
#
# Allow anonymous FTP? (Disabled by default).
anonymous_enable=NO
#
# Uncomment this to allow local users to log in.
local_enable=YES
#
# Uncomment this to enable any form of FTP write command.
write_enable=YES
#
# Default umask for local users is 077. You may wish to change this to 022,
# if your users expect that (022 is used by most other ftpd's)
local_umask=022
#
# Uncomment this to allow the anonymous FTP user to upload files. This only
# has an effect if the above global write enable is activated. Also, you will
# obviously need to create a directory writable by the FTP user.
#anon_upload_enable=YES
#
# Uncomment this if you want the anonymous FTP user to be able to create
# new directories.
#anon_mkdir_write_enable=YES
#
# Activate directory messages - messages given to remote users when they
# go into a certain directory.
dirmessage_enable=YES
#
# If enabled, vsftpd will display directory listings with the time
# in  your  local  time  zone.  The default is to display GMT. The
# times returned by the MDTM FTP command are also affected by this
# option.
use_localtime=YES
#
# Activate logging of uploads/downloads.
xferlog_enable=YES
#
# Make sure PORT transfer connections originate from port 20 (ftp-data).
connect_from_port_20=YES
#
# If you want, you can arrange for uploaded anonymous files to be owned by
# a different user. Note! Using "root" for uploaded files is not
# recommended!
#chown_uploads=YES
#chown_username=whoever
#
# You may override where the log file goes if you like. The default is shown
# below.
xferlog_file=/var/log/vsftpd.log
#
# If you want, you can have your log file in standard ftpd xferlog format.
# Note that the default log file location is /var/log/xferlog in this case.
#xferlog_std_format=YES
#
# You may change the default value for timing out an idle session.
#idle_session_timeout=600
#
# You may change the default value for timing out a data connection.
#data_connection_timeout=120
#
# It is recommended that you define on your system a unique user which the
# ftp server can use as a totally isolated and unprivileged user.
#nopriv_user=ftpsecure
#
# Enable this and the server will recognise asynchronous ABOR requests. Not
# recommended for security (the code is non-trivial). Not enabling it,
# however, may confuse older FTP clients.
#async_abor_enable=YES
#
# By default the server will pretend to allow ASCII mode but in fact ignore
# the request. Turn on the below options to have the server actually do ASCII
# mangling on files when in ASCII mode.
# Beware that on some FTP servers, ASCII support allows a denial of service
# attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd
# predicted this attack and has always been safe, reporting the size of the
# raw file.
# ASCII mangling is a horrible feature of the protocol.
#ascii_upload_enable=YES
#ascii_download_enable=YES
#
# You may fully customise the login banner string:
#ftpd_banner=Welcome to blah FTP service.
#
# You may specify a file of disallowed anonymous e-mail addresses. Apparently
# useful for combatting certain DoS attacks.
#deny_email_enable=YES
# (default follows)
#banned_email_file=/etc/vsftpd.banned_emails
#
# You may restrict local users to their home directories.  See the FAQ for
# the possible risks in this before using chroot_local_user or
# chroot_list_enable below.
#chroot_local_user=YES
#
# You may specify an explicit list of local users to chroot() to their home
# directory. If chroot_local_user is YES, then this list becomes a list of
# users to NOT chroot().
# (Warning! chroot'ing can be very dangerous. If using chroot, make sure that
# the user does not have write access to the top level directory within the
# chroot)
chroot_local_user=YES
chroot_list_enable=YES
# (default follows)
chroot_list_file=/etc/vsftpd.chroot_list
#
# You may activate the "-R" option to the builtin ls. This is disabled by
# default to avoid remote users being able to cause excessive I/O on large
# sites. However, some broken FTP clients such as "ncftp" and "mirror" assume
# the presence of the "-R" option, so there is a strong case for enabling it.
#ls_recurse_enable=YES
#
# Customization
#
# Some of vsftpd's settings don't fit the filesystem layout by
# default.
#
# This option should be the name of a directory which is empty.  Also, the
# directory should not be writable by the ftp user. This directory is used
# as a secure chroot() jail at times vsftpd does not require filesystem
# access.
secure_chroot_dir=/var/run/vsftpd/empty
#
# This string is the name of the PAM service vsftpd will use.
pam_service_name=vsftpd
#
# This option specifies the location of the RSA certificate to use for SSL
# encrypted connections.
rsa_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem
rsa_private_key_file=/etc/ssl/private/ssl-cert-snakeoil.key
ssl_enable=NO

#
# Uncomment this to indicate that vsftpd use a utf8 filesystem.
#utf8_filesystem=YES

Решено: vsftpd

[gluk47@gluk47-desktop ~]$ ензу куищще
куищще is aliased to `reboot’

Re: Решено: vsftpd

Сообщение

rm_ » 26.05.2010 13:44

Re: Решено: vsftpd

Сообщение

gluk47 » 26.05.2010 15:21

# ls /var/log/vsftp*
ls: невозможно получить доступ к /var/log/vsftp*: Нет такого файла или каталога
# service vsftpd restart
Завершение работы vsftpd:                              [   ОК  ]
Запускается vsftpd для vsftpd:                         [   ОК  ]
Запускается vsftpd для vsftpd.ipv6:                    [ ОШИБКА ]
# # ls /var/log/vsftp*
ls: невозможно получить доступ к /var/log/vsftp*: Нет такого файла или каталога

$ netstat -nlp|grep ftp
(Not all processes could be identified, non-owned process info
 will not be shown, you would have to be root to see it all.)
# netstat -nlp|grep ftp
tcp        0      0 0.0.0.0:21                  0.0.0.0:*                   LISTEN      28934/vsftpd

[gluk47@gluk47-desktop ~]$ ензу куищще
куищще is aliased to `reboot’

Re: Решено: vsftpd

Сообщение

SLEDopit » 26.05.2010 15:52

 $ head -1 /etc/issue
Debian GNU/Linux squeeze/sid n l
 $ ls -l /var/log/vsftpd.log
-rw-r----- 1 root adm 7165 May 25 21:20 /var/log/vsftpd.log

syslog_enable
If  enabled,  then  any  log  output  which  would  have gone to
/var/log/vsftpd.log goes to the system log instead.  Logging  is
done under the FTPD facility.
Default: NO

UNIX is basically a simple operating system, but you have to be a genius to understand the simplicity. © Dennis Ritchie
The more you believe you don’t do mistakes, the more bugs are in your code.

Re: Решено: vsftpd

Сообщение

gluk47 » 26.05.2010 18:10

Да нет, логи туда создаются (/var/log/vsftpd.log), но там только записи о подключениях. А про ошибку там не было ни слова (и про успешный запуск демона).

[gluk47@gluk47-desktop ~]$ ензу куищще
куищще is aliased to `reboot’

Re: Решено: vsftpd

Сообщение

KiWi » 26.05.2010 20:59