Volvo vehicles, like any other vehicles, also generate many unwarranted error codes. Error codes often occur in heavy duty vehicles due to high torque and high load. The error codes most frequently encountered by users are from from the Adblue system.
When we say Adblue systems, we often think about system that breaks very easily. These systems are often used in heavy loads and commercial vehicles. Lately, it has begun to be used in passenger cars. these systems are not used in most countries, even if they are mandatory in Europe. Because it is not structured correctly. Even the adblue liquid, that this system uses, is very difficult to find on the market. Like we said, the system is unstable and users are having trouble. It is a very difficult situation when the systems breaks in the middle of road . Repair of the system is very costly and you lose precious time. For this reason, users are often looking for solutions. One of the solution is an Adblue Emulator developed by SAIL TECHNOLOGY. It is a permanent solution and will be there right beside you in every situation. Adblue Emulators, which many users prefer, will not let you down.
So what do these emulators do and what information do they give? Below are the benefits and fault code information of the SAIL Technology Adblue Emulator we have listed for you.
The instructional models are designed for: Volvo B11R (3), Volvo B5LH (3), Volvo B5TL (3), Volvo B8R (3), Volvo FH (4).
Attention: Please visit https://canbusemulator.com for more detailed information about diagnostic trouble codes
DTC DTC
DTC Code Name
Type of malfunction
P001676
Crankshaft Position — Correlation with Camshaft Position
Incorrect installation position
P003A99
Turbocharger / turbocharger supercharging control position «A» has exceeded the training threshold
Parameter limit exceeded
P004513
Open in turbocharger / turbocharger supercharging control circuit «A»
Open circuit
P004519
Open in turbocharger / turbocharger supercharging control circuit «A»
Current in the circuit above the threshold
P004577
Open in turbocharger / turbocharger supercharging control circuit «A»
The required position is unattainable
P004591
Open in turbocharger / turbocharger supercharging control circuit «A»
Parametric
P004592
Open in turbocharger / turbocharger supercharging control circuit «A»
Characteristics or malfunctioning
P00459A
Open in turbocharger / turbocharger supercharging control circuit «A»
Working conditions of a component or system
P006964
Correlation of absolute pressure in the reservoir and barometric pressure
Violation of signal reliability
P006E16
Supply voltage control circuit turbocharger / turbocharger «A»
Voltage in the circuit below the threshold
P006E17
Supply voltage control circuit turbocharger / turbocharger «A»
Voltage in the circuit above the threshold
P007011
Outdoor temperature sensor «A»
Short to ground
P007015
Outdoor temperature sensor «A»
Circuit short to battery voltage or break
P008700
The pressure in the fuel distribution pipe / system is too low, row 1
No subtype information
P008800
The pressure in the fuel distribution pipe / system is too high, row 1
No subtype information
P008A00
The pressure in the low-pressure fuel system is too low
No subtype information
P008B00
The pressure in the low-pressure fuel system is too high
No subtype information
P008B97
The pressure in the low-pressure fuel system is too high
The operation of the component or system is difficult or blocked
P009011
Control of fuel pressure regulator 1
Short to ground
P009012
Control of fuel pressure regulator 1
Circuit Short to Battery Voltage
P009013
Control of fuel pressure regulator 1
Open circuit
P009400
A leak in the fuel system — a small leak
No subtype information
P009A00
Air temperature at engine intake — correlation
No subtype information
P009B11
Fuel Pressure Relief Control
Short to ground
P009B12
Fuel Pressure Relief Control
Circuit Short to Battery Voltage
P009B13
Fuel Pressure Relief Control
Open circuit
P009B73
Fuel Pressure Relief Control
The actuator jammed in the closed position
P00AF41
Performance characteristics of the turbocharger / turbocharger supercharger control module «A»
Total checksum error
P00C600
Too low pressure in the fuel distribution pipe — engine crankshaft rotation
No subtype information
P010501
Absolute pressure sensor in the manifold / barometric pressure
General electrical fault
P010512
Absolute pressure sensor in the manifold / barometric pressure
Circuit Short to Battery Voltage
P010513
Absolute pressure sensor in the manifold / barometric pressure
Open circuit
P010562
Absolute pressure sensor in the manifold / barometric pressure
Signal comparison error
P011001
Intake air temperature sensor 1, row 1
General electrical fault
P011011
Intake air temperature sensor 1, row 1
Short to ground
P011013
Intake air temperature sensor 1, row 1
Open circuit
P011501
Engine Coolant Temperature Sensor 1
General electrical fault
P011511
Engine Coolant Temperature Sensor 1
Short to ground
P011513
Engine Coolant Temperature Sensor 1
Open circuit
P01152A
Engine Coolant Temperature Sensor 1
Stuck signal in the range
P012011
Throttle / Pedal Position Sensor «A»
Short to ground
P012012
Throttle / Pedal Position Sensor «A»
Circuit Short to Battery Voltage
P012800
Coolant thermostat (coolant temperature below the thermostat control temperature)
No subtype information
P016800
Fuel temperature in engine too high
No subtype information
P016E00
Control of the fuel pressure in a closed loop at the limit is too high a pressure
No subtype information
P016F00
Controlling the fuel pressure in a closed loop at the limit is too low a pressure
No subtype information
P018501
Fuel temperature sensor «B»
General electrical fault
P018511
Fuel temperature sensor «B»
Short to ground
P018513
Fuel temperature sensor «B»
Open circuit
P018564
Fuel temperature sensor «B»
Violation of signal reliability
P019001
Pressure sensor in the fuel distributor pipe, row 1
General electrical fault
P019011
Pressure sensor in the fuel distributor pipe, row 1
Short to ground
P019013
Pressure sensor in the fuel distributor pipe, row 1
Open circuit
P019062
Pressure sensor in the fuel distributor pipe, row 1
Signal comparison error
P019064
Pressure sensor in the fuel distributor pipe, row 1
Violation of signal reliability
P019511
Engine oil temperature sensor «A»
Short to ground
P019513
Engine oil temperature sensor «A»
Open circuit
P019564
Engine oil temperature sensor «A»
Violation of signal reliability
P01B901
Engine oil temperature sensor «B»
General electrical fault
P01B911
Engine oil temperature sensor «B»
Short to ground
P01B913
Engine oil temperature sensor «B»
Open circuit
P020111
Cylinder 1 nozzle «A»
Short to ground
P020112
Cylinder 1 nozzle «A»
Circuit Short to Battery Voltage
P020113
Cylinder 1 nozzle «A»
Open circuit
P020156
Cylinder 1 nozzle «A»
Invalid / incompatible configuration
P020211
Cylinder 2 injector «A»
Short to ground
P020212
Cylinder 2 injector «A»
Circuit Short to Battery Voltage
P020213
Cylinder 2 injector «A»
Open circuit
P020256
Cylinder 2 injector «A»
Invalid / incompatible configuration
P020311
Cylinder 3 injector «A»
Short to ground
P020312
Cylinder 3 injector «A»
Circuit Short to Battery Voltage
P020313
Cylinder 3 injector «A»
Open circuit
P020356
Cylinder 3 injector «A»
Invalid / incompatible configuration
P020411
Cylinder 4 nozzle «A»
Short to ground
P020412
Cylinder 4 nozzle «A»
Circuit Short to Battery Voltage
P020413
Cylinder 4 nozzle «A»
Open circuit
P020456
Cylinder 4 nozzle «A»
Invalid / incompatible configuration
P020511
Cylinder 5 injector «A»
Short to ground
P020512
Cylinder 5 injector «A»
Circuit Short to Battery Voltage
P020513
Cylinder 5 injector «A»
Open circuit
P020556
Cylinder 5 injector «A»
Invalid / incompatible configuration
P020611
Cylinder 6 nozzle «A»
Short to ground
P020612
Cylinder 6 nozzle «A»
Circuit Short to Battery Voltage
P020613
Cylinder 6 nozzle «A»
Open circuit
P020656
Cylinder 6 nozzle «A»
Invalid / incompatible configuration
P021700
Engine coolant temperature exceeded status
No subtype information
P021800
The condition of the transmission oil temperature rise
No subtype information
P021900
State of excess of engine speed
No subtype information
P023400
Overcharging state of turbocharger / supercharger
No subtype information
P024311
Solenoid of the bypass damper «A» of the turbocharger / supercharger
Short to ground
P024312
Solenoid of the bypass damper «A» of the turbocharger / supercharger
Circuit Short to Battery Voltage
P024313
Solenoid of the bypass damper «A» of the turbocharger / supercharger
Open circuit
P025612
Fuel Injector Diesel Injector
Circuit Short to Battery Voltage
P025614
Fuel Injector Diesel Injector
Short to ground or open
P025692
Fuel Injector Diesel Injector
Characteristics or malfunctioning
P026A00
The efficiency of the charge air cooler is below the threshold
No subtype information
P029800
Excess temperature of engine oil
No subtype information
P029900
Insufficient supercharging of the turbocharger / supercharger
No subtype information
P02CC00
Fuel injector cylinder 1 — determination of the correction at the minimum limit
No subtype information
P02CD00
Fuel injector cylinder 1 — determination of the correction at the maximum limit
No subtype information
P02CE00
Fuel injector cylinder 2 — determination of the correction at the minimum limit
No subtype information
P02CF00
Fuel injector cylinder 2 — determination of the correction at the maximum limit
No subtype information
P02D000
Fuel injector cylinder 3 — determination of the correction at the minimum limit
No subtype information
P02D100
Fuel injector cylinder 3 — determination of the correction at the maximum limit
No subtype information
P02D200
Fuel injector of the cylinder 4 — determination of the correction at the minimum limit
No subtype information
P02D300
Fuel injector cylinder 4 — determination of the correction at the maximum limit
No subtype information
P02D400
Fuel injector cylinder 5 — determination of the correction at the minimum limit
No subtype information
P02D500
Fuel injector cylinder 5 — determination of the correction at the maximum limit
No subtype information
P02D600
Fuel injector of the cylinder 6 — determination of the correction at the minimum limit
No subtype information
P02D700
Fuel injector of the cylinder 6 — determination of the correction at the maximum limit
No subtype information
P02E011
Airflow control at the diesel engine inlet
Short to ground
P02E012
Airflow control at the diesel engine inlet
Circuit Short to Battery Voltage
P02E013
Airflow control at the diesel engine inlet
Open circuit
P02E07C
Airflow control at the diesel engine inlet
Slow reaction
P02E09B
Airflow control at the diesel engine inlet
High / excessive flow
P02E09C
Airflow control at the diesel engine inlet
Low / insufficient flow
P02E601
Diesel Engine Admission Regulator Position Sensor
General electrical fault
P02E612
Diesel Engine Admission Regulator Position Sensor
Circuit Short to Battery Voltage
P02E613
Diesel Engine Admission Regulator Position Sensor
Open circuit
P02E697
Diesel Engine Admission Regulator Position Sensor
The operation of the component or system is difficult or blocked
P02E699
Diesel Engine Admission Regulator Position Sensor
Parameter limit exceeded
P03351F
Crankshaft Position Sensor «A»
Intermittent signal in the circuit
P033531
Crankshaft Position Sensor «A»
Missing signal
P033538
Crankshaft Position Sensor «A»
Incorrect signal frequency
P034031
Camshaft position sensor «A» — row 1 or separate sensor
Missing signal
P034038
Camshaft position sensor «A» — row 1 or separate sensor
Incorrect signal frequency
P04007C
Exhaust gas recirculation flow «A»
Slow reaction
P04009B
Exhaust gas recirculation flow «A»
High / excessive flow
P04009C
Exhaust gas recirculation flow «A»
Low / insufficient flow
P040311
Control of EGR «A»
Short to ground
P040312
Control of EGR «A»
Circuit Short to Battery Voltage
P040313
Control of EGR «A»
Open circuit
P040341
Control of EGR «A»
Total checksum error
P040371
Control of EGR «A»
Driven drive
P040392
Control of EGR «A»
Characteristics or malfunctioning
P040901
The differential pressure sensor EGR
General electrical fault
P040912
The differential pressure sensor EGR
Circuit Short to Battery Voltage
P040913
The differential pressure sensor EGR
Open circuit
P040964
The differential pressure sensor EGR
Violation of signal reliability
P040A01
Temperature sensor «A» of the exhaust gas recirculation system
General electrical fault
P040A11
Temperature sensor «A» of the exhaust gas recirculation system
Short to ground
P040A13
Temperature sensor «A» of the exhaust gas recirculation system
Open circuit
P040A64
Temperature sensor «A» of the exhaust gas recirculation system
Violation of signal reliability
P041A11
Temperature sensor circuit «B» of the exhaust gas recirculation system
Short to ground
P041A12
Temperature sensor circuit «B» of the exhaust gas recirculation system
Circuit Short to Battery Voltage
P041A2A
Temperature sensor circuit «B» of the exhaust gas recirculation system
Stuck signal in the range
P042000
The efficiency of the catalyst system is below the threshold
No subtype information
P047001
The gauge of pressure of exhaust gases «A»
General electrical fault
P047012
The gauge of pressure of exhaust gases «A»
Circuit Short to Battery Voltage
P047013
The gauge of pressure of exhaust gases «A»
Open circuit
P047064
The gauge of pressure of exhaust gases «A»
Violation of signal reliability
P047511
Exhaust Pressure Control Valve «A»
Short to ground
P047512
Exhaust Pressure Control Valve «A»
Circuit Short to Battery Voltage
P047513
Exhaust Pressure Control Valve «A»
Open circuit
P047572
Exhaust Pressure Control Valve «A»
The actuator jammed in the open position
P048011
Fan control circuit 1
Short to ground
P048012
Fan control circuit 1
Circuit Short to Battery Voltage
P048013
Fan control circuit 1
Open circuit
P048613
Sensor «B» of the EGR system
Open circuit
P049D99
Control position «A» EGR exceeded the threshold of training
Parameter limit exceeded
P04D900
Control of the closed loop EGR system at the limit — the flow is too small
No subtype information
P04DA00
Control of the closed loop EGR system at the limit — the flow is too strong
No subtype information
P050011
Vehicle speed by wheel
Short to ground
P050013
Vehicle speed by wheel
Open circuit
P051A01
Crankcase Pressure Sensor
General electrical fault
P051A12
Crankcase Pressure Sensor
Circuit Short to Battery Voltage
P051A13
Crankcase Pressure Sensor
Open circuit
P051A64
Crankcase Pressure Sensor
Violation of signal reliability
P052001
Engine oil pressure switch / relay «A»
General electrical fault
P052012
Engine oil pressure switch / relay «A»
Circuit Short to Battery Voltage
P052013
Engine oil pressure switch / relay «A»
Open circuit
P052064
Engine oil pressure switch / relay «A»
Violation of signal reliability
P052400
Engine oil pressure too low
Engine oil pressure too low
P052607
Fan Speed Sensor Circuit
Mechanical faults
P052612
Fan Speed Sensor Circuit
Circuit Short to Battery Voltage
P053E00
Crankcase pressure — too high
No subtype information
P054001
Control of the inlet air heater «A»
General electrical fault
P054011
Control of the inlet air heater «A»
Short to ground
P054013
Control of the inlet air heater «A»
Open circuit
P054070
Control of the inlet air heater «A»
Drive stuck when on
P05407F
Control of the inlet air heater «A»
Drive stuck when turned off
P054464
Exhaust temperature sensor — Row 1 Sensor 1
Violation of signal reliability
P055A01
Engine oil pressure switch / relay «B»
General electrical fault
P055A12
Engine oil pressure switch / relay «B»
Circuit Short to Battery Voltage
P055A13
Engine oil pressure switch / relay «B»
Open circuit
P055A64
Engine oil pressure switch / relay «B»
Violation of signal reliability
P055F00
Engine oil pressure out of range
No subtype information
P05E311
Parking brake sensor / switch circuit
Short to ground
P05E362
Parking brake sensor / switch circuit
Signal comparison error
P05E364
Parking brake sensor / switch circuit
Violation of signal reliability
P061511
Starter relay
Short to ground
P061512
Starter relay
Circuit Short to Battery Voltage
P061513
Starter relay
Open circuit
P06279C
Fuel pump control «A»
Low / insufficient flow
P064111
Sensor reference voltage «A»
Short to ground
P064112
Sensor reference voltage «A»
Circuit Short to Battery Voltage
P06411C
Sensor reference voltage «A»
Output from the voltage range in the circuit
P065111
Sensor reference voltage «V»
Short to ground
P066601
Internal temperature sensor for control module «A»
General electrical fault
P066611
Internal temperature sensor for control module «A»
Short to ground
P06B016
Sensor supply voltage «A»
Voltage in the circuit below the threshold
P06B017
Sensor supply voltage «A»
Voltage in the circuit above the threshold
P06B316
Sensor supply «B»
Voltage in the circuit below the threshold
P06B317
Sensor supply «B»
Voltage in the circuit above the threshold
P06DA71
Engine Oil Pressure Adjustment
Driven drive
P06E616
Sensor supply voltage «C»
Voltage in the circuit below the threshold
P06E617
Sensor supply voltage «C»
Voltage in the circuit above the threshold
P073021
Recommended transfer
The amplitude of the signal is less than the minimum
P073022
Recommended transfer
The amplitude of the signal above the maximum value
P07307C
Recommended transfer
Slow reaction
P100101
Engine stop switch
General electrical fault
P100111
Engine stop switch
Short to ground
P100112
Engine stop switch
Circuit Short to Battery Voltage
P100190
Engine stop switch
Clogged in the open position
P100192
Engine stop switch
Characteristics or malfunctioning
P100211
Pre-heater heater relay
Short to ground
P100212
Pre-heater heater relay
Circuit Short to Battery Voltage
P100213
Pre-heater heater relay
Open circuit
P100701
Air filter indicator
General electrical fault
P100711
Air filter indicator
Short to ground
P100712
Air filter indicator
Circuit Short to Battery Voltage
P100713
Air filter indicator
Open circuit
P101711
Valve for draining water from fuel
Short to ground
P101E11
The valve of full blocking of the channel of a transmission
Short to ground
P101E12
The valve of full blocking of the channel of a transmission
Circuit Short to Battery Voltage
P101E13
The valve of full blocking of the channel of a transmission
Open circuit
P102111
Volvo Compression Brake Control Circuit (VCB)
Short to ground
P102112
Volvo Compression Brake Control Circuit (VCB)
Circuit Short to Battery Voltage
P102113
Volvo Compression Brake Control Circuit (VCB)
Open circuit
P108600
The oil level is moderately low
No subtype information
P109300
Engine oil pressure is moderately low
No subtype information
P10C011
Volvo Compression Brake Control Circuit (VCB) «2»
Short to ground
P10C012
Volvo Compression Brake Control Circuit (VCB) «2»
Circuit Short to Battery Voltage
P10C013
Volvo Compression Brake Control Circuit (VCB) «2»
Open circuit
P10E100
Differential pressure in particulate filter is critical
No subtype information
P10E200
Differential pressure on particulate filter moderately high
No subtype information
P10F800
Air filter clogged
No subtype information
P10FE00
Clogging of particulate filter — soot accumulation moderately high — row 1
No subtype information
P110400
Factory setting
No subtype information
P110501
Back-up switch circuit «A» of the engine
General electrical fault
P110511
Back-up switch circuit «A» of the engine
Short to ground
P110512
Back-up switch circuit «A» of the engine
Circuit Short to Battery Voltage
P110573
Back-up switch circuit «A» of the engine
The actuator jammed in the closed position
P111600
Absolute pressure sensor in the reservoir is a moderate excess
No subtype information
P111800
Absolute pressure sensor in the collector — a strong excess
No subtype information
P111945
The intake manifold temperature is too high at a moderate level
Failure of program memory
P111A00
Intake manifold temperature too high
No subtype information
P111D00
The engine coolant level is moderately low
No subtype information
P111E00
Engine coolant temperature is moderately high
No subtype information
P112500
Engine oil temperature — moderately high
No subtype information
P112800
The oil pressure for cooling the pistons is moderately low
No subtype information
P112900
Transmission oil temperature moderately high
No subtype information
P112B00
The turbocharger / turbocharger drive temperature «A»
No subtype information
P112E00
Exhaust gas temperature moderately high — row 1
No subtype information
P113411
Air purge valve for fuel injection into the exhaust aftertreatment system
Short to ground
P113413
Air purge valve for fuel injection into the exhaust aftertreatment system
Open circuit
P113472
Air purge valve for fuel injection into the exhaust aftertreatment system
The actuator jammed in the open position
P113473
Air purge valve for fuel injection into the exhaust aftertreatment system
The actuator jammed in the closed position
P113500
Crankcase pressure too high relative to atmospheric pressure
No subtype information
P113600
Error of calibration of the correlation of NOx 1/2 sensors — row 1
No subtype information
P113711
Oil thermostat
Short to ground
P113712
Oil thermostat
Circuit Short to Battery Voltage
P113713
Oil thermostat
Open circuit
P113F11
Idling switch confirmation cable with buffering — VECU side
Short to ground
P113F12
Idling switch confirmation cable with buffering — VECU side
Circuit Short to Battery Voltage
P114000
Volvo Compression Brake Control (VCB) — too low oil temperature
No subtype information
P114101
Idling switch confirmation cable with buffering — ECM side
General electrical fault
P114113
Idling switch confirmation cable with buffering — ECM side
Open circuit
P114123
Idling switch confirmation cable with buffering — ECM side
Constantly low signal level
P114124
Idling switch confirmation cable with buffering — ECM side
Constantly high signal level
P114411
High voltage side of the starter relay
Short to ground
P114412
High voltage side of the starter relay
Circuit Short to Battery Voltage
P114413
High voltage side of the starter relay
Open circuit
P114500
The level of the reducing agent is moderately low
No subtype information
P114700
Pressure in the fuel distribution pipe / system, row 1 — moderately too high
No subtype information
P114B00
The turbocharger / turbocharger drive temperature «A» is too low
No subtype information
P114E00
EGR drive temperature outside the operating range
No subtype information
P115000
Correlation of Sensor / Switch Voltage «A» / «D» Throttle Position / Pedal Position
No subtype information
P115100
Excess temperature of the post-treatment system
No subtype information
P115211
Starting fuel pump
Short to ground
P115212
Starting fuel pump
Circuit Short to Battery Voltage
P115213
Starting fuel pump
Open circuit
P115400
The connection between the bodywork control module «A» and the instrument cluster control module (IPC)
No subtype information
P117311
Low Transmission Range Authorization Valve
Short to ground
P117312
Low Transmission Range Authorization Valve
Circuit Short to Battery Voltage
P117313
Low Transmission Range Authorization Valve
Open circuit
P117401
Transmission range inquiry
General electrical fault
P117411
Transmission range inquiry
Short to ground
P117412
Transmission range inquiry
Circuit Short to Battery Voltage
P117600
Starter motor is deactivated — temperature rise
No subtype information
P117700
Starter motor is deactivated — gearbox is not in neutral position
No subtype information
P117800
The starter motor is deactivated — the gear of the electric motor of the starter motor is stuck
No subtype information
P117900
Starter motor is deactivated — power take-off is active
No subtype information
P117B01
Temperature sensor switch in engine compartment
General electrical fault
P117B11
Temperature sensor switch in engine compartment
Short to ground
P117B12
Temperature sensor switch in engine compartment
Circuit Short to Battery Voltage
P117C00
The requested range of gears is too high
No subtype information
P117D00
Requested driver transfer too low
No subtype information
P117E00
Driver’s request is too high
No subtype information
P117F11
Bypass valve of the hydraulic valve
Short to ground
P117F12
Bypass valve of the hydraulic valve
Circuit Short to Battery Voltage
P117F13
Bypass valve of the hydraulic valve
Open circuit
P203164
Exhaust temperature sensor — Row 1 Sensor 2
Violation of signal reliability
P203A86
Reagent level sensor «A»
Invalid signal
P203F00
Reducer level is low
No subtype information
P204F93
Characteristics of the SCR system — dosing failure
Does not work
P207F9A
Quality of the reducing agent
Working conditions of a component or system
P20D711
Controlling the fuel supply to the exhaust aftertreatment system
Short to ground
P20D713
Controlling the fuel supply to the exhaust aftertreatment system
Open circuit
P20D773
Controlling the fuel supply to the exhaust aftertreatment system
The actuator jammed in the closed position
P20DD01
Fuel pressure sensor for exhaust gas aftertreatment
General electrical fault
P20DD12
Fuel pressure sensor for exhaust gas aftertreatment
Circuit Short to Battery Voltage
P20DD13
Fuel pressure sensor for exhaust gas aftertreatment
Open circuit
P20EE00
The efficiency of the SCR NOx catalyst is below the threshold (row 1)
No subtype information
P20F400
AdBlue consumption is too low
No subtype information
P20F500
Reducer consumption too high
No subtype information
P210900
Performance characteristics of the «A» minimum limiter of the throttle / pedal position
No subtype information
P213600
Correlation of Sensor / Switch Voltage «A» / «C» Throttle Position / Pedal Position
No subtype information
P215A62
Correlation of vehicle speed with wheel speed
Signal comparison error
P215A64
Correlation of vehicle speed with wheel speed
Violation of signal reliability
P216300
Performance characteristics of the maximum limit sensor «A» of the throttle / pedal position
No subtype information
P220012
NOx sensor — series 1 sensor 1
Circuit Short to Battery Voltage
P220013
NOx sensor — series 1 sensor 1
Open circuit
P22001C
NOx sensor — series 1 sensor 1
Output from the voltage range in the circuit
P220064
NOx sensor — series 1 sensor 1
Violation of signal reliability
P220093
NOx sensor — series 1 sensor 1
Does not work
P222601
Barometric pressure circuit
General electrical fault
P222612
Barometric pressure circuit
Circuit Short to Battery Voltage
P222613
Barometric pressure circuit
Open circuit
P222664
Barometric pressure circuit
Violation of signal reliability
P225C00
Characteristics of the NOx sensor — high level signaling — row 1 sensor 1
No subtype information
P225D00
Characteristics of the NOx sensor — low level of the signal — row 1 sensor 1
No subtype information
P225E67
Characteristics of the NOx sensor — high level signaling — row 1 sensor 2
Wrong signal after event
P225F00
Characteristics of the NOx sensor — low level of the signal — row 1 sensor 2
No subtype information
P226401
Water sensor in fuel
General electrical fault
P226411
Water sensor in fuel
Short to ground
P226413
Water sensor in fuel
Open circuit
P228D72
The fuel pressure regulator 1 has exceeded the control limits — too high a pressure
The actuator jammed in the open position
P228E00
The fuel pressure regulator 1 has exceeded the training limits — too low a pressure
No subtype information
P228F00
The fuel pressure regulator 1 has exceeded the training limits — too high a pressure
No subtype information
P229E12
NOx sensor — row 1 sensor 2
Circuit Short to Battery Voltage
P229E13
NOx sensor — row 1 sensor 2
Open circuit
P229E1C
NOx sensor — row 1 sensor 2
Output from the voltage range in the circuit
P229E64
NOx sensor — row 1 sensor 2
Violation of signal reliability
P229E93
NOx sensor — row 1 sensor 2
Does not work
P22FB92
Sensor Specifications NOx — Sensor — Row 1 Sensor 1
Characteristics or malfunctioning
P22FE00
Sensor Specifications NOx — Sensor — Row 1 Sensor 2
No subtype information
P242800
Exhaust gas temperature too high
No subtype information
P242A64
Exhaust temperature sensor — Row 1 Sensor 3
Violation of signal reliability
P244A00
Differential pressure on the diesel particulate filter after-treatment 1 is too small (row 1)
No subtype information
P244B00
The differential pressure on the diesel particulate filter after-treatment 1 is too large (row 1)
No subtype information
P244C00
The exhaust gas temperature is too low to regenerate the particulate filter (row 1)
No subtype information
P245264
Particulate filter pressure sensor «A»
Violation of signal reliability
P245700
Coolant efficiency of the exhaust gas recirculation system is below the threshold value
No subtype information
P246300
Clogged particulate filter — soot accumulation — row 1
No subtype information
P249D00
Control of the injection of the reducing agent in a closed loop at the limit — the flow is too small
No subtype information
P249E00
Injection of the reducing agent in a closed loop at the limit — the flow is too high
No subtype information
P249F92
Excessive time for switching to the closed-loop diesel particulate filter regeneration control mode
Characteristics or malfunctioning
P24A000
Control of DPF regeneration in a closed loop at the limit — the temperature is too low
No subtype information
P24A100
Control of DPF regeneration in a closed loop at the limit — the temperature is too high
No subtype information
P24A200
The regeneration of the diesel particulate filter is not complete (row 1)
No subtype information
P24A400
Clogging of the diesel particulate filter — soot accumulation too large (row 1)
No subtype information
P250A11
Engine oil level sensor
Short to ground
P250A13
Engine oil level sensor
Open circuit
P250F00
Engine oil level too low
No subtype information
P253901
Low Fuel Pressure Sensor Circuit
General electrical fault
P253912
Low Fuel Pressure Sensor Circuit
Circuit Short to Battery Voltage
P253913
Low Fuel Pressure Sensor Circuit
Open circuit
P255601
Engine Coolant Level Sensor / Relay
General electrical fault
P255611
Engine Coolant Level Sensor / Relay
Short to ground
P255612
Engine Coolant Level Sensor / Relay
Circuit Short to Battery Voltage
P255613
Engine Coolant Level Sensor / Relay
Open circuit
P256000
Engine Coolant Level — Low
No subtype information
P256214
Sensor «A» turbocharger supercharging control position
Short to ground or open
P256214
Sensor «A» turbocharger supercharging control position
Short to ground or open
P259C00
Excessive time for entering the supercharging control of the turbocharger «A» in a closed loop
No subtype information
P25A911
Control oil supply for cooling pistons
Short to ground
P25A912
Control oil supply for cooling pistons
Circuit Short to Battery Voltage
P25A913
Control oil supply for cooling pistons
Open circuit
P25A971
Control oil supply for cooling pistons
Driven drive
P25AE00
The oil pressure for cooling the pistons is too low
No subtype information
P260011
Coolant Pump Control Circuit / Break
Short to ground
P260012
Coolant Pump Control Circuit / Break
Circuit Short to Battery Voltage
P260013
Coolant Pump Control Circuit / Break
Open circuit
P268111
Control of the bypass valve «A» of the engine coolant
Short to ground
P268112
Control of the bypass valve «A» of the engine coolant
Circuit Short to Battery Voltage
P268113
Control of the bypass valve «A» of the engine coolant
Open circuit
P269711
Injection Fuel Injector «A»
Short to ground
P269713
Injection Fuel Injector «A»
Open circuit
P269773
Injection Fuel Injector «A»
The actuator jammed in the closed position
P26977A
Injection Fuel Injector «A»
Fluid leakage or seal failure
P2A1612
Control unit «D» fuel flow meter injection pump (cam / rotor / nozzle)
Circuit Short to Battery Voltage
P2A1614
Control unit «D» fuel flow meter injection pump (cam / rotor / nozzle)
Short to ground or open
P2A1692
Control unit «D» fuel flow meter injection pump (cam / rotor / nozzle)
Characteristics or malfunctioning
P2A1E12
Control unit «F» fuel flow meter injection pump (cam / rotor / injector)
Circuit Short to Battery Voltage
P2A1E14
Control unit «F» fuel flow meter injection pump (cam / rotor / injector)
Short to ground or open
P2A1E92
Control unit «F» fuel flow meter injection pump (cam / rotor / injector)
Characteristics or malfunctioning
U000188
CAN Backbone bus 2 communication network
Bus Off
U001088
CAN Backbone bus 1 of the communication network
Bus Off
U008088
Communication Subnet of the car engine
Bus Off
U010100
Lost Communication With TECU
No subtype information
U010A00
Lost communication with the A module of the exhaust gas recirculation system
No subtype information
U010C00
The communication with the turbocharger / supercharger control module is broken
No subtype information
U012100
The communication with the anti-lock braking system (ABS)
No subtype information
U012900
Lost Communication With Brake Control Module
No subtype information
U014100
Lost connection with VMCU
No subtype information
U014200
Lost connection with the body control module «B»
No subtype information
U015500
Communication with the instrument cluster control module (IPC) is broken
No subtype information
U016700
Lost communication with the car immobilizer control module
No subtype information
U029D00
Communication with NOx sensor «A» is broken
No subtype information
U029E00
The communication with the NOx sensor «B» is broken
No subtype information
U032300
Software incompatibility with the dashboard control module
No subtype information
U033100
Incompatibility of software with the bodywork control module «A»
No subtype information
U042600
From the immobilizer control module of the car, unreliable data
No subtype information
U116600
Lost communication with CIOM
No subtype information
U116900
Lost connection with DACU
No subtype information
U116B00
Communication with TCM on the high-speed communication bus CAN
No subtype information
U116C00
Communication with TCM on the CAN bus of the power plant is broken
No subtype information
U116F00
Communication with the control module of the supply of the reducing agent via the engine subnetwork is broken
No subtype information
U117100
The communication with the control unit of the body equipment via the high-speed communication bus CAN
No subtype information
U117300
The communication with the IPC control unit via the high-speed communication CAN
No subtype information
U117888
CAN bus communication system bus
Bus Off
U1FFF68
Factory mode active
Event details
U300001
Electronic control module
General electrical fault
U300041
Electronic control module
Total checksum error
U300044
Electronic control module
Data memory failure
U300045
Electronic control module
Failure of program memory
U300049
Electronic control module
Internal failure of electronics
U300257
Vehicle Identification Number
Invalid / incompatible software component
TECU, диагностические коды неисправности
| Диагностический код неисправности | Название кода DTC | Тип неисправности |
|---|---|---|
| P105017 | Датчик положения демультипликатора (SEPoR) | Напряжение в цепи выше порога |
| P105018 | Датчик положения демультипликатора (SEPoR) | Ток в цепи ниже пороговой величины |
| P105019 | Датчик положения демультипликатора (SEPoR) | Ток в цепи выше порога |
| P105054 | Датчик положения демультипликатора (SEPoR) | Отсутствует калибровка |
| P105117 | Датчик положения делителя (SEPoS) | Напряжение в цепи выше порога |
| P105118 | Датчик положения делителя (SEPoS) | Ток в цепи ниже пороговой величины |
| P105119 | Датчик положения делителя (SEPoS) | Ток в цепи выше порога |
| P105154 | Датчик положения делителя (SEPoS) | Отсутствует калибровка |
| P105217 | Положение цилиндра сцепления | Напряжение в цепи выше порога |
| P105218 | Положение цилиндра сцепления | Ток в цепи ниже пороговой величины |
| P105229 | Положение цилиндра сцепления | Недопустимый сигнал |
| P105254 | Положение цилиндра сцепления | Отсутствует калибровка |
| P105262 | Положение цилиндра сцепления | Ошибка сравнения сигнала |
| P105378 | Износ диска сцепления | Неверная юстировка или регулировка |
| P105417 | Датчик давления воздуха в баке (SEPrSA) | Напряжение в цепи выше порога |
| P105418 | Датчик давления воздуха в баке (SEPrSA) | Ток в цепи ниже пороговой величины |
| P105421 | Датчик давления воздуха в баке (SEPrSA) | Амплитуда сигнала меньше минимума |
| P105422 | Датчик давления воздуха в баке (SEPrSA) | Амплитуда сигнала выше максимальной величины |
| P105594 | Выключатель тормоза, состояние | Неожиданная операция |
| P105716 | Датчик скорости главного вала (SESM) | Напряжение в цепи ниже порога |
| P105717 | Датчик скорости главного вала (SESM) | Напряжение в цепи выше порога |
| P105718 | Датчик скорости главного вала (SESM) | Ток в цепи ниже пороговой величины |
| P105721 | Датчик скорости главного вала (SESM) | Амплитуда сигнала меньше минимума |
| P105729 | Датчик скорости главного вала (SESM) | Недопустимый сигнал |
| P105816 | Датчик скорости промежуточного вала (SESC) | Напряжение в цепи ниже порога |
| P105817 | Датчик скорости промежуточного вала (SESC) | Напряжение в цепи выше порога |
| P105818 | Датчик скорости промежуточного вала (SESC) | Ток в цепи ниже пороговой величины |
| P105821 | Датчик скорости промежуточного вала (SESC) | Амплитуда сигнала меньше минимума |
| P105916 | Датчик температуры масла в коробке передач (SETeGO) | Напряжение в цепи ниже порога |
| P105918 | Датчик температуры масла в коробке передач (SETeGO) | Ток в цепи ниже пороговой величины |
| P105922 | Датчик температуры масла в коробке передач (SETeGO) | Амплитуда сигнала выше максимальной величины |
| P105992 | Датчик температуры масла в коробке передач (SETeGO) | Характеристики или неправильное функционирование |
| P105998 | Датчик температуры масла в коробке передач (SETeGO) | Перегрев компонента или системы |
| P105A17 | Клапан повышенного ряда (VAHR) | Напряжение в цепи выше порога |
| P105A18 | Клапан повышенного ряда (VAHR) | Ток в цепи ниже пороговой величины |
| P105A19 | Клапан повышенного ряда (VAHR) | Ток в цепи выше порога |
| P105B17 | Клапан пониженного ряда (VALR) | Напряжение в цепи выше порога |
| P105B18 | Клапан пониженного ряда (VALR) | Ток в цепи ниже пороговой величины |
| P105B19 | Клапан пониженного ряда (VALR) | Ток в цепи выше порога |
| P105C17 | Клапан прямого делителя (VADS) | Напряжение в цепи выше порога |
| P105C18 | Клапан прямого делителя (VADS) | Ток в цепи ниже пороговой величины |
| P105C19 | Клапан прямого делителя (VADS) | Ток в цепи выше порога |
| P105D17 | Клапан непрямого делителя (VAIDS) | Напряжение в цепи выше порога |
| P105D18 | Клапан непрямого делителя (VAIDS) | Ток в цепи ниже пороговой величины |
| P105D19 | Клапан непрямого делителя (VAIDS) | Ток в цепи выше порога |
| P105E17 | Датчик положения переключателя 1 (SEPo1R) | Напряжение в цепи выше порога |
| P105E18 | Датчик положения переключателя 1 (SEPo1R) | Ток в цепи ниже пороговой величины |
| P105E19 | Датчик положения переключателя 1 (SEPo1R) | Ток в цепи выше порога |
| P105E54 | Датчик положения переключателя 1 (SEPo1R) | Отсутствует калибровка |
| P105F17 | Датчик положения переключателя 2 (SEPo23) | Напряжение в цепи выше порога |
| P105F18 | Датчик положения переключателя 2 (SEPo23) | Ток в цепи ниже пороговой величины |
| P105F19 | Датчик положения переключателя 2 (SEPo23) | Ток в цепи выше порога |
| P105F54 | Датчик положения переключателя 2 (SEPo23) | Отсутствует калибровка |
| P106063 | Нагрузка диска сцепления | Тайм-аут защиты цепи/компонента |
| P106074 | Нагрузка диска сцепления | Проскальзывание исполнительного механизма |
| P106093 | Нагрузка диска сцепления | Не функционирует |
| P106094 | Нагрузка диска сцепления | Неожиданная операция |
| P106154 | Положение точки проскальзывания цилиндра сцепления | Отсутствует калибровка |
| P106216 | Питание датчика положения сцепления (SEPoC5V) | Напряжение в цепи ниже порога |
| P106218 | Питание датчика положения сцепления (SEPoC5V) | Ток в цепи ниже пороговой величины |
| P106329 | Датчик наклона коробки передач (SEIG) | Недопустимый сигнал |
| P106417 | Клапан быстрого включения сцепления (VAFE) | Напряжение в цепи выше порога |
| P106418 | Клапан быстрого включения сцепления (VAFE) | Ток в цепи ниже пороговой величины |
| P106419 | Клапан быстрого включения сцепления (VAFE) | Ток в цепи выше порога |
| P106517 | Клапан медленного включения сцепления (VASE) | Напряжение в цепи выше порога |
| P106518 | Клапан медленного включения сцепления (VASE) | Ток в цепи ниже пороговой величины |
| P106519 | Клапан медленного включения сцепления (VASE) | Ток в цепи выше порога |
| P106617 | Клапан быстрого выключения сцепления (VAFD) | Напряжение в цепи выше порога |
| P106618 | Клапан быстрого выключения сцепления (VAFD) | Ток в цепи ниже пороговой величины |
| P106619 | Клапан быстрого выключения сцепления (VAFD) | Ток в цепи выше порога |
| P106717 | Клапан медленного выключения сцепления (VASD) | Напряжение в цепи выше порога |
| P106718 | Клапан медленного выключения сцепления (VASD) | Ток в цепи ниже пороговой величины |
| P106719 | Клапан медленного выключения сцепления (VASD) | Ток в цепи выше порога |
| P106A17 | Клапан 1 передачи (VAG1) | Напряжение в цепи выше порога |
| P106A18 | Клапан 1 передачи (VAG1) | Ток в цепи ниже пороговой величины |
| P106A19 | Клапан 1 передачи (VAG1) | Ток в цепи выше порога |
| P106B17 | Клапан задней передачи (VAGR) | Напряжение в цепи выше порога |
| P106B18 | Клапан задней передачи (VAGR) | Ток в цепи ниже пороговой величины |
| P106B19 | Клапан задней передачи (VAGR) | Ток в цепи выше порога |
| P106C17 | Клапан 2 передачи (VAG2) | Напряжение в цепи выше порога |
| P106C18 | Клапан 2 передачи (VAG2) | Ток в цепи ниже пороговой величины |
| P106C19 | Клапан 2 передачи (VAG2) | Ток в цепи выше порога |
| P106D17 | Клапан 3 передачи (VAG3) | Напряжение в цепи выше порога |
| P106D18 | Клапан 3 передачи (VAG3) | Ток в цепи ниже пороговой величины |
| P106D19 | Клапан 3 передачи (VAG3) | Ток в цепи выше порога |
| P107017 | Клапан тормоза коробки передач (VAGB) | Напряжение в цепи выше порога |
| P107018 | Клапан тормоза коробки передач (VAGB) | Ток в цепи ниже пороговой величины |
| P107019 | Клапан тормоза коробки передач (VAGB) | Ток в цепи выше порога |
| P107177 | Система включения делителя | Требуемое положение недостижимо |
| P107179 | Система включения делителя | Неисправность механического рычажного механизма |
| P107192 | Система включения делителя | Характеристики или неправильное функционирование |
| P107194 | Система включения делителя | Неожиданная операция |
| P107196 | Система включения делителя | Внутренний отказ компонента |
| P107197 | Система включения делителя | Функционирование компонента или системы затруднено или заблокировано |
| P107277 | Система включения демультипликатора | Требуемое положение недостижимо |
| P107292 | Система включения демультипликатора | Характеристики или неправильное функционирование |
| P107294 | Система включения демультипликатора | Неожиданная операция |
| P107297 | Система включения демультипликатора | Функционирование компонента или системы затруднено или заблокировано |
| P107371 | Система включения 1 и задней передач | Заело привод |
| P107377 | Система включения 1 и задней передач | Требуемое положение недостижимо |
| P107392 | Система включения 1 и задней передач | Характеристики или неправильное функционирование |
| P107394 | Система включения 1 и задней передач | Неожиданная операция |
| P107396 | Система включения 1 и задней передач | Внутренний отказ компонента |
| P107397 | Система включения 1 и задней передач | Функционирование компонента или системы затруднено или заблокировано |
| P107471 | Система включения 2 и 3 передач | Заело привод |
| P107477 | Система включения 2 и 3 передач | Требуемое положение недостижимо |
| P107492 | Система включения 2 и 3 передач | Характеристики или неправильное функционирование |
| P107494 | Система включения 2 и 3 передач | Неожиданная операция |
| P107496 | Система включения 2 и 3 передач | Внутренний отказ компонента |
| P107497 | Система включения 2 и 3 передач | Функционирование компонента или системы затруднено или заблокировано |
| P107538 | Система сцепления | Неверная частота сигнала |
| P107554 | Система сцепления | Отсутствует калибровка |
| P107571 | Система сцепления | Заело привод |
| P107572 | Система сцепления | Исполнительный механизм заклинил в открытом положении |
| P107574 | Система сцепления | Проскальзывание исполнительного механизма |
| P107575 | Система сцепления | Аварийное положение недостижимо |
| P107577 | Система сцепления | Требуемое положение недостижимо |
| P107586 | Система сцепления | Недопустимый сигнал |
| P107592 | Система сцепления | Характеристики или неправильное функционирование |
| P107594 | Система сцепления | Неожиданная операция |
| P107694 | Тормоз коробки передач | Неожиданная операция |
| P107B86 | Положение педали акселератора / характеристики сигнала выключателя тормозов | Недопустимый сигнал |
| P109317 | Цепь стороны высокого уровня клапана передачи 1 (VAG1HS) | Напряжение в цепи выше порога |
| P109319 | Цепь стороны высокого уровня клапана передачи 1 (VAG1HS) | Ток в цепи выше порога |
| P109417 | Цепь стороны высокого уровня клапана задней передачи | Напряжение в цепи выше порога |
| P109419 | Цепь стороны высокого уровня клапана задней передачи | Ток в цепи выше порога |
| P109517 | Цепь стороны высокого уровня внутреннего клапана 1 (VAIN1HS) | Напряжение в цепи выше порога |
| P109519 | Цепь стороны высокого уровня внутреннего клапана 1 (VAIN1HS) | Ток в цепи выше порога |
| P109617 | Цепь стороны высокого уровня внутреннего клапана 2 (VAIN2HS) | Напряжение в цепи выше порога |
| P109619 | Цепь стороны высокого уровня внутреннего клапана 2 (VAIN2HS) | Ток в цепи выше порога |
| P10A017 | Цепь стороны высокого уровня медленных клапанов сцепления (VASHS) | Напряжение в цепи выше порога |
| P10A019 | Цепь стороны высокого уровня медленных клапанов сцепления (VASHS) | Ток в цепи выше порога |
| P10A117 | Цепь стороны высокого уровня быстрых клапанов сцепления (VAFHS) | Напряжение в цепи выше порога |
| P10A119 | Цепь стороны высокого уровня быстрых клапанов сцепления (VAFHS) | Ток в цепи выше порога |
| P10AE81 | Включена передача в нейтральном положении | Получены недопустимые данные по последовательному каналу |
| U000188 | CAN Магистральная шина 2 коммуникационной сети | Шина отключена |
| U001088 | CAN Магистральная шина 1 коммуникационной сети | Шина отключена |
| U007387 | CAN Коммуникационная подсеть силовой установки | Отсутствует сообщение |
| U007388 | CAN Коммуникационная подсеть силовой установки | Шина отключена |
| U010000 | Потеряна связь с EMS | Информация о подтипе отсутствует |
| U012900 | Потеряна связь с модулем управления тормозной системой | Информация о подтипе отсутствует |
| U014000 | Потеряна связь с VMCU | Информация о подтипе отсутствует |
| U030055 | Программирование памяти ЭППЗУ ПО разработки | Не сконфигурировано |
| U030081 | Программирование памяти ЭППЗУ ПО разработки | Получены недопустимые данные по последовательному каналу |
| U114100 | Потеряна связь с HMIIOM | Информация о подтипе отсутствует |
| U114286 | Скорость автомобиля по колесу | Недопустимый сигнал |
| U300017 | Электронный модуль управления | Напряжение в цепи выше порога |
| U300041 | Электронный модуль управления | Ошибка общей контрольной суммы |
| U300044 | Электронный модуль управления | Отказ памяти данных |
| U300046 | Электронный модуль управления | Отказ памяти калибровки/параметров |
| U30004B | Электронный модуль управления | Перегрев |
| U300055 | Электронный модуль управления | Не сконфигурировано |
| U300316 | Питание от аккумулятора | Напряжение в цепи ниже порога |
| U300317 | Питание от аккумулятора | Напряжение в цепи выше порога |
and ru
- Регистрация
- 6 Май 2023
- Сообщения
- 3
- Марка машины
- Volvo
- Модель Volvo
- S60 II
- Город
- Москва
- Регион
- Москва
- #1
Появились такие ошибки.
ECM-P042000
ECM-P001500
ECM-U012900
ECM-P001568
Kertman
Клубная СТО «Инавто»
- Регистрация
- 19 февраля 2012
- Сообщения
- 4,485
- Город
- Санкт-Петербург
- Регион
- Санкт-Петербург
- Имя
- Игорь
- #2
Появились такие ошибки.
ECM-P042000
ECM-P001500
ECM-U012900
ECM-P001568
Вин авто ?
and ru
- Регистрация
- 6 Май 2023
- Сообщения
- 3
- Марка машины
- Volvo
- Модель Volvo
- S60 II
- Город
- Москва
- Регион
- Москва
- #3
YV1PS61H0D2197445
добавлено сообщение
-
IMG-20230506-WA0020.jpg
84.6 KB · Просмотры: 13
Kertman
Клубная СТО «Инавто»
- Регистрация
- 19 февраля 2012
- Сообщения
- 4,485
- Город
- Санкт-Петербург
- Регион
- Санкт-Петербург
- Имя
- Игорь
and ru
- Регистрация
- 6 Май 2023
- Сообщения
- 3
- Марка машины
- Volvo
- Модель Volvo
- S60 II
- Город
- Москва
- Регион
- Москва
- #5
YV1FS61H0D2197445
Неправильно написал первый раз.
Kertman
Клубная СТО «Инавто»
- Регистрация
- 19 февраля 2012
- Сообщения
- 4,485
- Город
- Санкт-Петербург
- Регион
- Санкт-Петербург
- Имя
- Игорь
- #6
284: ECM-P001500 Синхронизация положения распредвала на выпуске (В) — слишком позднее положение (ряд 1). Информация об общей ошибке. Нет информации о типе переходника, B5254T12
|
||||
|
Volvo vehicles, like any other vehicles, also generate many unwarranted error codes. Error codes often occur in heavy duty vehicles due to high torque and high load. The error codes most frequently encountered by users are from from the Adblue system.
When we say Adblue systems, we often think about system that breaks very easily. These systems are often used in heavy loads and commercial vehicles. Lately, it has begun to be used in passenger cars. these systems are not used in most countries, even if they are mandatory in Europe. Because it is not structured correctly. Even the adblue liquid, that this system uses, is very difficult to find on the market. Like we said, the system is unstable and users are having trouble. It is a very difficult situation when the systems breaks in the middle of road . Repair of the system is very costly and you lose precious time. For this reason, users are often looking for solutions. One of the solution is an Adblue Emulator developed by SAIL TECHNOLOGY. It is a permanent solution and will be there right beside you in every situation. Adblue Emulators, which many users prefer, will not let you down.
So what do these emulators do and what information do they give? Below are the benefits and fault code information of the SAIL Technology Adblue Emulator we have listed for you.
The instructional models are designed for: Volvo B11R (3), Volvo B5LH (3), Volvo B5TL (3), Volvo B8R (3), Volvo FH (4).
Attention: Please visit https://www.canbusemulator.com/en for more detailed information about diagnostic trouble codes
|
DTC |
DTC Code Name |
Type of malfunction |
|
P01951F |
Engine Oil Temperature Sensor «A» |
Circuit Intermittent |
|
B150413 |
Vision Camera 1 Heater Circuit |
Circuit Open |
|
P001676 |
Crankshaft Position — Correlation with Camshaft Position |
Incorrect installation position |
|
P003A99 |
Turbocharger / turbocharger supercharging control position «A» has exceeded the training threshold |
Parameter limit exceeded |
|
P004513 |
Open in turbocharger / turbocharger supercharging control circuit «A» |
Open circuit |
|
P004519 |
Open in turbocharger / turbocharger supercharging control circuit «A» |
Current in the circuit above the threshold |
|
P004577 |
Open in turbocharger / turbocharger supercharging control circuit «A» |
The required position is unattainable |
|
P004591 |
Open in turbocharger / turbocharger supercharging control circuit «A» |
Parametric |
|
P004592 |
Open in turbocharger / turbocharger supercharging control circuit «A» |
Characteristics or malfunctioning |
|
P00459A |
Open in turbocharger / turbocharger supercharging control circuit «A» |
Working conditions of a component or system |
|
P006964 |
Correlation of absolute pressure in the reservoir and barometric pressure |
Violation of signal reliability |
|
P006E16 |
Supply voltage control circuit turbocharger / turbocharger «A» |
Voltage in the circuit below the threshold |
|
P006E17 |
Supply voltage control circuit turbocharger / turbocharger «A» |
Voltage in the circuit above the threshold |
|
P007011 |
Outdoor temperature sensor «A» |
Short to ground |
|
P007015 |
Outdoor temperature sensor «A» |
Circuit short to battery voltage or break |
|
P008700 |
The pressure in the fuel distribution pipe / system is too low, row 1 |
No subtype information |
|
P008800 |
The pressure in the fuel distribution pipe / system is too high, row 1 |
No subtype information |
|
P008A00 |
The pressure in the low-pressure fuel system is too low |
No subtype information |
|
P008B00 |
The pressure in the low-pressure fuel system is too high |
No subtype information |
|
P008B97 |
The pressure in the low-pressure fuel system is too high |
The operation of the component or system is difficult or blocked |
|
P009011 |
Control of fuel pressure regulator 1 |
Short to ground |
|
P009012 |
Control of fuel pressure regulator 1 |
Circuit Short to Battery Voltage |
|
P009013 |
Control of fuel pressure regulator 1 |
Open circuit |
|
P009400 |
A leak in the fuel system — a small leak |
No subtype information |
|
P009A00 |
Air temperature at engine intake — correlation |
No subtype information |
|
P009B11 |
Fuel Pressure Relief Control |
Short to ground |
|
P009B12 |
Fuel Pressure Relief Control |
Circuit Short to Battery Voltage |
|
P009B13 |
Fuel Pressure Relief Control |
Open circuit |
|
P009B73 |
Fuel Pressure Relief Control |
The actuator jammed in the closed position |
|
P00AF41 |
Performance characteristics of the turbocharger / turbocharger supercharger control module «A» |
Total checksum error |
|
P00C600 |
Too low pressure in the fuel distribution pipe — engine crankshaft rotation |
No subtype information |
|
P010501 |
Absolute pressure sensor in the manifold / barometric pressure |
General electrical fault |
|
P010512 |
Absolute pressure sensor in the manifold / barometric pressure |
Circuit Short to Battery Voltage |
|
P010513 |
Absolute pressure sensor in the manifold / barometric pressure |
Open circuit |
|
P010562 |
Absolute pressure sensor in the manifold / barometric pressure |
Signal comparison error |
|
P011001 |
Intake air temperature sensor 1, row 1 |
General electrical fault |
|
P011011 |
Intake air temperature sensor 1, row 1 |
Short to ground |
|
P011013 |
Intake air temperature sensor 1, row 1 |
Open circuit |
|
P011501 |
Engine Coolant Temperature Sensor 1 |
General electrical fault |
|
P011511 |
Engine Coolant Temperature Sensor 1 |
Short to ground |
|
P011513 |
Engine Coolant Temperature Sensor 1 |
Open circuit |
|
P01152A |
Engine Coolant Temperature Sensor 1 |
Stuck signal in the range |
|
P012011 |
Throttle / Pedal Position Sensor «A» |
Short to ground |
|
P012012 |
Throttle / Pedal Position Sensor «A» |
Circuit Short to Battery Voltage |
|
P012800 |
Coolant thermostat (coolant temperature below the thermostat control temperature) |
No subtype information |
|
P016800 |
Fuel temperature in engine too high |
No subtype information |
|
P016E00 |
Control of the fuel pressure in a closed loop at the limit is too high a pressure |
No subtype information |
|
P016F00 |
Controlling the fuel pressure in a closed loop at the limit is too low a pressure |
No subtype information |
|
P018501 |
Fuel temperature sensor «B» |
General electrical fault |
|
P018511 |
Fuel temperature sensor «B» |
Short to ground |
|
P018513 |
Fuel temperature sensor «B» |
Open circuit |
|
P018564 |
Fuel temperature sensor «B» |
Violation of signal reliability |
|
P019001 |
Pressure sensor in the fuel distributor pipe, row 1 |
General electrical fault |
|
P019011 |
Pressure sensor in the fuel distributor pipe, row 1 |
Short to ground |
|
P019013 |
Pressure sensor in the fuel distributor pipe, row 1 |
Open circuit |
|
P019062 |
Pressure sensor in the fuel distributor pipe, row 1 |
Signal comparison error |
|
P019064 |
Pressure sensor in the fuel distributor pipe, row 1 |
Violation of signal reliability |
|
P019511 |
Engine oil temperature sensor «A» |
Short to ground |
|
P019513 |
Engine oil temperature sensor «A» |
Open circuit |
|
P019564 |
Engine oil temperature sensor «A» |
Violation of signal reliability |
|
P01B901 |
Engine oil temperature sensor «B» |
General electrical fault |
|
P01B911 |
Engine oil temperature sensor «B» |
Short to ground |
|
P01B913 |
Engine oil temperature sensor «B» |
Open circuit |
|
P020111 |
Cylinder 1 nozzle «A» |
Short to ground |
|
P020112 |
Cylinder 1 nozzle «A» |
Circuit Short to Battery Voltage |
|
P020113 |
Cylinder 1 nozzle «A» |
Open circuit |
|
P020156 |
Cylinder 1 nozzle «A» |
Invalid / incompatible configuration |
|
P020211 |
Cylinder 2 injector «A» |
Short to ground |
|
P020212 |
Cylinder 2 injector «A» |
Circuit Short to Battery Voltage |
|
P020213 |
Cylinder 2 injector «A» |
Open circuit |
|
P020256 |
Cylinder 2 injector «A» |
Invalid / incompatible configuration |
|
P020311 |
Cylinder 3 injector «A» |
Short to ground |
|
P020312 |
Cylinder 3 injector «A» |
Circuit Short to Battery Voltage |
|
P020313 |
Cylinder 3 injector «A» |
Open circuit |
|
P020356 |
Cylinder 3 injector «A» |
Invalid / incompatible configuration |
|
P020411 |
Cylinder 4 nozzle «A» |
Short to ground |
|
P020412 |
Cylinder 4 nozzle «A» |
Circuit Short to Battery Voltage |
|
P020413 |
Cylinder 4 nozzle «A» |
Open circuit |
|
P020456 |
Cylinder 4 nozzle «A» |
Invalid / incompatible configuration |
|
P020511 |
Cylinder 5 injector «A» |
Short to ground |
|
P020512 |
Cylinder 5 injector «A» |
Circuit Short to Battery Voltage |
|
P020513 |
Cylinder 5 injector «A» |
Open circuit |
|
P020556 |
Cylinder 5 injector «A» |
Invalid / incompatible configuration |
|
P020611 |
Cylinder 6 nozzle «A» |
Short to ground |
|
P020612 |
Cylinder 6 nozzle «A» |
Circuit Short to Battery Voltage |
|
P020613 |
Cylinder 6 nozzle «A» |
Open circuit |
|
P020656 |
Cylinder 6 nozzle «A» |
Invalid / incompatible configuration |
|
P021700 |
Engine coolant temperature exceeded status |
No subtype information |
|
P021800 |
The condition of the transmission oil temperature rise |
No subtype information |
|
P021900 |
State of excess of engine speed |
No subtype information |
|
P023400 |
Overcharging state of turbocharger / supercharger |
No subtype information |
|
P024311 |
Solenoid of the bypass damper «A» of the turbocharger / supercharger |
Short to ground |
|
P024312 |
Solenoid of the bypass damper «A» of the turbocharger / supercharger |
Circuit Short to Battery Voltage |
|
P024313 |
Solenoid of the bypass damper «A» of the turbocharger / supercharger |
Open circuit |
|
P025612 |
Fuel Injector Diesel Injector |
Circuit Short to Battery Voltage |
|
P025614 |
Fuel Injector Diesel Injector |
Short to ground or open |
|
P025692 |
Fuel Injector Diesel Injector |
Characteristics or malfunctioning |
|
P026A00 |
The efficiency of the charge air cooler is below the threshold |
No subtype information |
|
P029800 |
Excess temperature of engine oil |
No subtype information |
|
P029900 |
Insufficient supercharging of the turbocharger / supercharger |
No subtype information |
|
P02CC00 |
Fuel injector cylinder 1 — determination of the correction at the minimum limit |
No subtype information |
|
P02CD00 |
Fuel injector cylinder 1 — determination of the correction at the maximum limit |
No subtype information |
|
P02CE00 |
Fuel injector cylinder 2 — determination of the correction at the minimum limit |
No subtype information |
|
P02CF00 |
Fuel injector cylinder 2 — determination of the correction at the maximum limit |
No subtype information |
|
P02D000 |
Fuel injector cylinder 3 — determination of the correction at the minimum limit |
No subtype information |
|
P02D100 |
Fuel injector cylinder 3 — determination of the correction at the maximum limit |
No subtype information |
|
P02D200 |
Fuel injector of the cylinder 4 — determination of the correction at the minimum limit |
No subtype information |
|
P02D300 |
Fuel injector cylinder 4 — determination of the correction at the maximum limit |
No subtype information |
|
P02D400 |
Fuel injector cylinder 5 — determination of the correction at the minimum limit |
No subtype information |
|
P02D500 |
Fuel injector cylinder 5 — determination of the correction at the maximum limit |
No subtype information |
|
P02D600 |
Fuel injector of the cylinder 6 — determination of the correction at the minimum limit |
No subtype information |
|
P02D700 |
Fuel injector of the cylinder 6 — determination of the correction at the maximum limit |
No subtype information |
|
P02E011 |
Airflow control at the diesel engine inlet |
Short to ground |
|
P02E012 |
Airflow control at the diesel engine inlet |
Circuit Short to Battery Voltage |
|
P02E013 |
Airflow control at the diesel engine inlet |
Open circuit |
|
P02E07C |
Airflow control at the diesel engine inlet |
Slow reaction |
|
P02E09B |
Airflow control at the diesel engine inlet |
High / excessive flow |
|
P02E09C |
Airflow control at the diesel engine inlet |
Low / insufficient flow |
|
P02E601 |
Diesel Engine Admission Regulator Position Sensor |
General electrical fault |
|
P02E612 |
Diesel Engine Admission Regulator Position Sensor |
Circuit Short to Battery Voltage |
|
P02E613 |
Diesel Engine Admission Regulator Position Sensor |
Open circuit |
|
P02E697 |
Diesel Engine Admission Regulator Position Sensor |
The operation of the component or system is difficult or blocked |
|
P02E699 |
Diesel Engine Admission Regulator Position Sensor |
Parameter limit exceeded |
|
P03351F |
Crankshaft Position Sensor «A» |
Intermittent signal in the circuit |
|
P033531 |
Crankshaft Position Sensor «A» |
Missing signal |
|
P033538 |
Crankshaft Position Sensor «A» |
Incorrect signal frequency |
|
P034031 |
Camshaft position sensor «A» — row 1 or separate sensor |
Missing signal |
|
P034038 |
Camshaft position sensor «A» — row 1 or separate sensor |
Incorrect signal frequency |
|
P04007C |
Exhaust gas recirculation flow «A» |
Slow reaction |
|
P04009B |
Exhaust gas recirculation flow «A» |
High / excessive flow |
|
P04009C |
Exhaust gas recirculation flow «A» |
Low / insufficient flow |
|
P040311 |
Control of EGR «A» |
Short to ground |
|
P040312 |
Control of EGR «A» |
Circuit Short to Battery Voltage |
|
P040313 |
Control of EGR «A» |
Open circuit |
|
P040341 |
Control of EGR «A» |
Total checksum error |
|
P040371 |
Control of EGR «A» |
Driven drive |
|
P040392 |
Control of EGR «A» |
Characteristics or malfunctioning |
|
P040901 |
The differential pressure sensor EGR |
General electrical fault |
|
P040912 |
The differential pressure sensor EGR |
Circuit Short to Battery Voltage |
|
P040913 |
The differential pressure sensor EGR |
Open circuit |
|
P040964 |
The differential pressure sensor EGR |
Violation of signal reliability |
|
P040A01 |
Temperature sensor «A» of the exhaust gas recirculation system |
General electrical fault |
|
P040A11 |
Temperature sensor «A» of the exhaust gas recirculation system |
Short to ground |
|
P040A13 |
Temperature sensor «A» of the exhaust gas recirculation system |
Open circuit |
|
P040A64 |
Temperature sensor «A» of the exhaust gas recirculation system |
Violation of signal reliability |
|
P041A11 |
Temperature sensor circuit «B» of the exhaust gas recirculation system |
Short to ground |
|
P041A12 |
Temperature sensor circuit «B» of the exhaust gas recirculation system |
Circuit Short to Battery Voltage |
|
P041A2A |
Temperature sensor circuit «B» of the exhaust gas recirculation system |
Stuck signal in the range |
|
P042000 |
The efficiency of the catalyst system is below the threshold |
No subtype information |
|
P047001 |
The gauge of pressure of exhaust gases «A» |
General electrical fault |
|
P047012 |
The gauge of pressure of exhaust gases «A» |
Circuit Short to Battery Voltage |
|
P047013 |
The gauge of pressure of exhaust gases «A» |
Open circuit |
|
P047064 |
The gauge of pressure of exhaust gases «A» |
Violation of signal reliability |
|
P047511 |
Exhaust Pressure Control Valve «A» |
Short to ground |
|
P047512 |
Exhaust Pressure Control Valve «A» |
Circuit Short to Battery Voltage |
|
P047513 |
Exhaust Pressure Control Valve «A» |
Open circuit |
|
P047572 |
Exhaust Pressure Control Valve «A» |
The actuator jammed in the open position |
|
P048011 |
Fan control circuit 1 |
Short to ground |
|
P048012 |
Fan control circuit 1 |
Circuit Short to Battery Voltage |
|
P048013 |
Fan control circuit 1 |
Open circuit |
|
P048613 |
Sensor «B» of the EGR system |
Open circuit |
|
P049D99 |
Control position «A» EGR exceeded the threshold of training |
Parameter limit exceeded |
|
P04D900 |
Control of the closed loop EGR system at the limit — the flow is too small |
No subtype information |
|
P04DA00 |
Control of the closed loop EGR system at the limit — the flow is too strong |
No subtype information |
|
P050011 |
Vehicle speed by wheel |
Short to ground |
|
P050013 |
Vehicle speed by wheel |
Open circuit |
|
P051A01 |
Crankcase Pressure Sensor |
General electrical fault |
|
P051A12 |
Crankcase Pressure Sensor |
Circuit Short to Battery Voltage |
|
P051A13 |
Crankcase Pressure Sensor |
Open circuit |
|
P051A64 |
Crankcase Pressure Sensor |
Violation of signal reliability |
|
P052001 |
Engine oil pressure switch / relay «A» |
General electrical fault |
|
P052012 |
Engine oil pressure switch / relay «A» |
Circuit Short to Battery Voltage |
|
P052013 |
Engine oil pressure switch / relay «A» |
Open circuit |
|
P052064 |
Engine oil pressure switch / relay «A» |
Violation of signal reliability |
|
P052400 |
Engine oil pressure too low |
Engine oil pressure too low |
|
P052607 |
Fan Speed Sensor Circuit |
Mechanical faults |
|
P052612 |
Fan Speed Sensor Circuit |
Circuit Short to Battery Voltage |
|
P053E00 |
Crankcase pressure — too high |
No subtype information |
|
P054001 |
Control of the inlet air heater «A» |
General electrical fault |
|
P054011 |
Control of the inlet air heater «A» |
Short to ground |
|
P054013 |
Control of the inlet air heater «A» |
Open circuit |
|
P054070 |
Control of the inlet air heater «A» |
Drive stuck when on |
|
P05407F |
Control of the inlet air heater «A» |
Drive stuck when turned off |
|
P054464 |
Exhaust temperature sensor — Row 1 Sensor 1 |
Violation of signal reliability |
|
P055A01 |
Engine oil pressure switch / relay «B» |
General electrical fault |
|
P055A12 |
Engine oil pressure switch / relay «B» |
Circuit Short to Battery Voltage |
|
P055A13 |
Engine oil pressure switch / relay «B» |
Open circuit |
|
P055A64 |
Engine oil pressure switch / relay «B» |
Violation of signal reliability |
|
P055F00 |
Engine oil pressure out of range |
No subtype information |
|
P05E311 |
Parking brake sensor / switch circuit |
Short to ground |
|
P05E362 |
Parking brake sensor / switch circuit |
Signal comparison error |
|
P05E364 |
Parking brake sensor / switch circuit |
Violation of signal reliability |
|
P061511 |
Starter relay |
Short to ground |
|
P061512 |
Starter relay |
Circuit Short to Battery Voltage |
|
P061513 |
Starter relay |
Open circuit |
|
P06279C |
Fuel pump control «A» |
Low / insufficient flow |
|
P064111 |
Sensor reference voltage «A» |
Short to ground |
|
P064112 |
Sensor reference voltage «A» |
Circuit Short to Battery Voltage |
|
P06411C |
Sensor reference voltage «A» |
Output from the voltage range in the circuit |
|
P065111 |
Sensor reference voltage «V» |
Short to ground |
|
P066601 |
Internal temperature sensor for control module «A» |
General electrical fault |
|
P066611 |
Internal temperature sensor for control module «A» |
Short to ground |
|
P06B016 |
Sensor supply voltage «A» |
Voltage in the circuit below the threshold |
|
P06B017 |
Sensor supply voltage «A» |
Voltage in the circuit above the threshold |
|
P06B316 |
Sensor supply «B» |
Voltage in the circuit below the threshold |
|
P06B317 |
Sensor supply «B» |
Voltage in the circuit above the threshold |
|
P06DA71 |
Engine Oil Pressure Adjustment |
Driven drive |
|
P06E616 |
Sensor supply voltage «C» |
Voltage in the circuit below the threshold |
|
P06E617 |
Sensor supply voltage «C» |
Voltage in the circuit above the threshold |
|
P073021 |
Recommended transfer |
The amplitude of the signal is less than the minimum |
|
P073022 |
Recommended transfer |
The amplitude of the signal above the maximum value |
|
P07307C |
Recommended transfer |
Slow reaction |
|
P100101 |
Engine stop switch |
General electrical fault |
|
P100111 |
Engine stop switch |
Short to ground |
|
P100112 |
Engine stop switch |
Circuit Short to Battery Voltage |
|
P100190 |
Engine stop switch |
Clogged in the open position |
|
P100192 |
Engine stop switch |
Characteristics or malfunctioning |
|
P100211 |
Pre-heater heater relay |
Short to ground |
|
P100212 |
Pre-heater heater relay |
Circuit Short to Battery Voltage |
|
P100213 |
Pre-heater heater relay |
Open circuit |
|
P100701 |
Air filter indicator |
General electrical fault |
|
P100711 |
Air filter indicator |
Short to ground |
|
P100712 |
Air filter indicator |
Circuit Short to Battery Voltage |
|
P100713 |
Air filter indicator |
Open circuit |
|
P101711 |
Valve for draining water from fuel |
Short to ground |
|
P101E11 |
The valve of full blocking of the channel of a transmission |
Short to ground |
|
P101E12 |
The valve of full blocking of the channel of a transmission |
Circuit Short to Battery Voltage |
|
P101E13 |
The valve of full blocking of the channel of a transmission |
Open circuit |
|
P102111 |
Volvo Compression Brake Control Circuit (VCB) |
Short to ground |
|
P102112 |
Volvo Compression Brake Control Circuit (VCB) |
Circuit Short to Battery Voltage |
|
P102113 |
Volvo Compression Brake Control Circuit (VCB) |
Open circuit |
|
P108600 |
The oil level is moderately low |
No subtype information |
|
P109300 |
Engine oil pressure is moderately low |
No subtype information |
|
P10C011 |
Volvo Compression Brake Control Circuit (VCB) «2» |
Short to ground |
|
P10C012 |
Volvo Compression Brake Control Circuit (VCB) «2» |
Circuit Short to Battery Voltage |
|
P10C013 |
Volvo Compression Brake Control Circuit (VCB) «2» |
Open circuit |
|
P10E100 |
Differential pressure in particulate filter is critical |
No subtype information |
|
P10E200 |
Differential pressure on particulate filter moderately high |
No subtype information |
|
P10F800 |
Air filter clogged |
No subtype information |
|
P10FE00 |
Clogging of particulate filter — soot accumulation moderately high — row 1 |
No subtype information |
|
P110400 |
Factory setting |
No subtype information |
|
P110501 |
Back-up switch circuit «A» of the engine |
General electrical fault |
|
P110511 |
Back-up switch circuit «A» of the engine |
Short to ground |
|
P110512 |
Back-up switch circuit «A» of the engine |
Circuit Short to Battery Voltage |
|
P110573 |
Back-up switch circuit «A» of the engine |
The actuator jammed in the closed position |
|
P111600 |
Absolute pressure sensor in the reservoir is a moderate excess |
No subtype information |
|
P111800 |
Absolute pressure sensor in the collector — a strong excess |
No subtype information |
|
P111945 |
The intake manifold temperature is too high at a moderate level |
Failure of program memory |
|
P111A00 |
Intake manifold temperature too high |
No subtype information |
|
P111D00 |
The engine coolant level is moderately low |
No subtype information |
|
P111E00 |
Engine coolant temperature is moderately high |
No subtype information |
|
P112500 |
Engine oil temperature — moderately high |
No subtype information |
|
P112800 |
The oil pressure for cooling the pistons is moderately low |
No subtype information |
|
P112900 |
Transmission oil temperature moderately high |
No subtype information |
|
P112B00 |
The turbocharger / turbocharger drive temperature «A» |
No subtype information |
|
P112E00 |
Exhaust gas temperature moderately high — row 1 |
No subtype information |
|
P113411 |
Air purge valve for fuel injection into the exhaust aftertreatment system |
Short to ground |
|
P113413 |
Air purge valve for fuel injection into the exhaust aftertreatment system |
Open circuit |
|
P113472 |
Air purge valve for fuel injection into the exhaust aftertreatment system |
The actuator jammed in the open position |
|
P113473 |
Air purge valve for fuel injection into the exhaust aftertreatment system |
The actuator jammed in the closed position |
|
P113500 |
Crankcase pressure too high relative to atmospheric pressure |
No subtype information |
|
P113600 |
Error of calibration of the correlation of NOx 1/2 sensors — row 1 |
No subtype information |
|
P113711 |
Oil thermostat |
Short to ground |
|
P113712 |
Oil thermostat |
Circuit Short to Battery Voltage |
|
P113713 |
Oil thermostat |
Open circuit |
|
P113F11 |
Idling switch confirmation cable with buffering — VECU side |
Short to ground |
|
P113F12 |
Idling switch confirmation cable with buffering — VECU side |
Circuit Short to Battery Voltage |
|
P114000 |
Volvo Compression Brake Control (VCB) — too low oil temperature |
No subtype information |
|
P114101 |
Idling switch confirmation cable with buffering — ECM side |
General electrical fault |
|
P114113 |
Idling switch confirmation cable with buffering — ECM side |
Open circuit |
|
P114123 |
Idling switch confirmation cable with buffering — ECM side |
Constantly low signal level |
|
P114124 |
Idling switch confirmation cable with buffering — ECM side |
Constantly high signal level |
|
P114411 |
High voltage side of the starter relay |
Short to ground |
|
P114412 |
High voltage side of the starter relay |
Circuit Short to Battery Voltage |
|
P114413 |
High voltage side of the starter relay |
Open circuit |
|
P114500 |
The level of the reducing agent is moderately low |
No subtype information |
|
P114700 |
Pressure in the fuel distribution pipe / system, row 1 — moderately too high |
No subtype information |
|
P114B00 |
The turbocharger / turbocharger drive temperature «A» is too low |
No subtype information |
|
P114E00 |
EGR drive temperature outside the operating range |
No subtype information |
|
P115000 |
Correlation of Sensor / Switch Voltage «A» / «D» Throttle Position / Pedal Position |
No subtype information |
|
P115100 |
Excess temperature of the post-treatment system |
No subtype information |
|
P115211 |
Starting fuel pump |
Short to ground |
|
P115212 |
Starting fuel pump |
Circuit Short to Battery Voltage |
|
P115213 |
Starting fuel pump |
Open circuit |
|
P115400 |
The connection between the bodywork control module «A» and the instrument cluster control module (IPC) |
No subtype information |
|
P117311 |
Low Transmission Range Authorization Valve |
Short to ground |
|
P117312 |
Low Transmission Range Authorization Valve |
Circuit Short to Battery Voltage |
|
P117313 |
Low Transmission Range Authorization Valve |
Open circuit |
|
P117401 |
Transmission range inquiry |
General electrical fault |
|
P117411 |
Transmission range inquiry |
Short to ground |
|
P117412 |
Transmission range inquiry |
Circuit Short to Battery Voltage |
|
P117600 |
Starter motor is deactivated — temperature rise |
No subtype information |
|
P117700 |
Starter motor is deactivated — gearbox is not in neutral position |
No subtype information |
|
P117800 |
The starter motor is deactivated — the gear of the electric motor of the starter motor is stuck |
No subtype information |
|
P117900 |
Starter motor is deactivated — power take-off is active |
No subtype information |
|
P117B01 |
Temperature sensor switch in engine compartment |
General electrical fault |
|
P117B11 |
Temperature sensor switch in engine compartment |
Short to ground |
|
P117B12 |
Temperature sensor switch in engine compartment |
Circuit Short to Battery Voltage |
|
P117C00 |
The requested range of gears is too high |
No subtype information |
|
P117D00 |
Requested driver transfer too low |
No subtype information |
|
P117E00 |
Driver’s request is too high |
No subtype information |
|
P117F11 |
Bypass valve of the hydraulic valve |
Short to ground |
|
P117F12 |
Bypass valve of the hydraulic valve |
Circuit Short to Battery Voltage |
|
P117F13 |
Bypass valve of the hydraulic valve |
Open circuit |
|
P203164 |
Exhaust temperature sensor — Row 1 Sensor 2 |
Violation of signal reliability |
|
P203A86 |
Reagent level sensor «A» |
Invalid signal |
|
P203F00 |
Reducer level is low |
No subtype information |
|
P204F93 |
Characteristics of the SCR system — dosing failure |
Does not work |
|
P207F9A |
Quality of the reducing agent |
Working conditions of a component or system |
|
P20D711 |
Controlling the fuel supply to the exhaust aftertreatment system |
Short to ground |
|
P20D713 |
Controlling the fuel supply to the exhaust aftertreatment system |
Open circuit |
|
P20D773 |
Controlling the fuel supply to the exhaust aftertreatment system |
The actuator jammed in the closed position |
|
P20DD01 |
Fuel pressure sensor for exhaust gas aftertreatment |
General electrical fault |
|
P20DD12 |
Fuel pressure sensor for exhaust gas aftertreatment |
Circuit Short to Battery Voltage |
|
P20DD13 |
Fuel pressure sensor for exhaust gas aftertreatment |
Open circuit |
|
P20EE00 |
The efficiency of the SCR NOx catalyst is below the threshold (row 1) |
No subtype information |
|
P20F400 |
AdBlue consumption is too low |
No subtype information |
|
P20F500 |
Reducer consumption too high |
No subtype information |
|
P210900 |
Performance characteristics of the «A» minimum limiter of the throttle / pedal position |
No subtype information |
|
P213600 |
Correlation of Sensor / Switch Voltage «A» / «C» Throttle Position / Pedal Position |
No subtype information |
|
P215A62 |
Correlation of vehicle speed with wheel speed |
Signal comparison error |
|
P215A64 |
Correlation of vehicle speed with wheel speed |
Violation of signal reliability |
|
P216300 |
Performance characteristics of the maximum limit sensor «A» of the throttle / pedal position |
No subtype information |
|
P220012 |
NOx sensor — series 1 sensor 1 |
Circuit Short to Battery Voltage |
|
P220013 |
NOx sensor — series 1 sensor 1 |
Open circuit |
|
P22001C |
NOx sensor — series 1 sensor 1 |
Output from the voltage range in the circuit |
|
P220064 |
NOx sensor — series 1 sensor 1 |
Violation of signal reliability |
|
P220093 |
NOx sensor — series 1 sensor 1 |
Does not work |
|
P222601 |
Barometric pressure circuit |
General electrical fault |
|
P222612 |
Barometric pressure circuit |
Circuit Short to Battery Voltage |
|
P222613 |
Barometric pressure circuit |
Open circuit |
|
P222664 |
Barometric pressure circuit |
Violation of signal reliability |
|
P225C00 |
Characteristics of the NOx sensor — high level signaling — row 1 sensor 1 |
No subtype information |
|
P225D00 |
Characteristics of the NOx sensor — low level of the signal — row 1 sensor 1 |
No subtype information |
|
P225E67 |
Characteristics of the NOx sensor — high level signaling — row 1 sensor 2 |
Wrong signal after event |
|
P225F00 |
Characteristics of the NOx sensor — low level of the signal — row 1 sensor 2 |
No subtype information |
|
P226401 |
Water sensor in fuel |
General electrical fault |
|
P226411 |
Water sensor in fuel |
Short to ground |
|
P226413 |
Water sensor in fuel |
Open circuit |
|
P228D72 |
The fuel pressure regulator 1 has exceeded the control limits — too high a pressure |
The actuator jammed in the open position |
|
P228E00 |
The fuel pressure regulator 1 has exceeded the training limits — too low a pressure |
No subtype information |
|
P228F00 |
The fuel pressure regulator 1 has exceeded the training limits — too high a pressure |
No subtype information |
|
P229E12 |
NOx sensor — row 1 sensor 2 |
Circuit Short to Battery Voltage |
|
P229E13 |
NOx sensor — row 1 sensor 2 |
Open circuit |
|
P229E1C |
NOx sensor — row 1 sensor 2 |
Output from the voltage range in the circuit |
|
P229E64 |
NOx sensor — row 1 sensor 2 |
Violation of signal reliability |
|
P229E93 |
NOx sensor — row 1 sensor 2 |
Does not work |
|
P22FB92 |
Sensor Specifications NOx — Sensor — Row 1 Sensor 1 |
Characteristics or malfunctioning |
|
P22FE00 |
Sensor Specifications NOx — Sensor — Row 1 Sensor 2 |
No subtype information |
|
P242800 |
Exhaust gas temperature too high |
No subtype information |
|
P242A64 |
Exhaust temperature sensor — Row 1 Sensor 3 |
Violation of signal reliability |
|
P244A00 |
Differential pressure on the diesel particulate filter after-treatment 1 is too small (row 1) |
No subtype information |
|
P244B00 |
The differential pressure on the diesel particulate filter after-treatment 1 is too large (row 1) |
No subtype information |
|
P244C00 |
The exhaust gas temperature is too low to regenerate the particulate filter (row 1) |
No subtype information |
|
P245264 |
Particulate filter pressure sensor «A» |
Violation of signal reliability |
|
P245700 |
Coolant efficiency of the exhaust gas recirculation system is below the threshold value |
No subtype information |
|
P246300 |
Clogged particulate filter — soot accumulation — row 1 |
No subtype information |
|
P249D00 |
Control of the injection of the reducing agent in a closed loop at the limit — the flow is too small |
No subtype information |
|
P249E00 |
Injection of the reducing agent in a closed loop at the limit — the flow is too high |
No subtype information |
|
P249F92 |
Excessive time for switching to the closed-loop diesel particulate filter regeneration control mode |
Characteristics or malfunctioning |
|
P24A000 |
Control of DPF regeneration in a closed loop at the limit — the temperature is too low |
No subtype information |
|
P24A100 |
Control of DPF regeneration in a closed loop at the limit — the temperature is too high |
No subtype information |
|
P24A200 |
The regeneration of the diesel particulate filter is not complete (row 1) |
No subtype information |
|
P24A400 |
Clogging of the diesel particulate filter — soot accumulation too large (row 1) |
No subtype information |
|
P250A11 |
Engine oil level sensor |
Short to ground |
|
P250A13 |
Engine oil level sensor |
Open circuit |
|
P250F00 |
Engine oil level too low |
No subtype information |
|
P253901 |
Low Fuel Pressure Sensor Circuit |
General electrical fault |
|
P253912 |
Low Fuel Pressure Sensor Circuit |
Circuit Short to Battery Voltage |
|
P253913 |
Low Fuel Pressure Sensor Circuit |
Open circuit |
|
P255601 |
Engine Coolant Level Sensor / Relay |
General electrical fault |
|
P255611 |
Engine Coolant Level Sensor / Relay |
Short to ground |
|
P255612 |
Engine Coolant Level Sensor / Relay |
Circuit Short to Battery Voltage |
|
P255613 |
Engine Coolant Level Sensor / Relay |
Open circuit |
|
P256000 |
Engine Coolant Level — Low |
No subtype information |
|
P256214 |
Sensor «A» turbocharger supercharging control position |
Short to ground or open |
|
P256214 |
Sensor «A» turbocharger supercharging control position |
Short to ground or open |
|
P259C00 |
Excessive time for entering the supercharging control of the turbocharger «A» in a closed loop |
No subtype information |
|
P25A911 |
Control oil supply for cooling pistons |
Short to ground |
|
P25A912 |
Control oil supply for cooling pistons |
Circuit Short to Battery Voltage |
|
P25A913 |
Control oil supply for cooling pistons |
Open circuit |
|
P25A971 |
Control oil supply for cooling pistons |
Driven drive |
|
P25AE00 |
The oil pressure for cooling the pistons is too low |
No subtype information |
|
P260011 |
Coolant Pump Control Circuit / Break |
Short to ground |
|
P260012 |
Coolant Pump Control Circuit / Break |
Circuit Short to Battery Voltage |
|
P260013 |
Coolant Pump Control Circuit / Break |
Open circuit |
|
P268111 |
Control of the bypass valve «A» of the engine coolant |
Short to ground |
|
P268112 |
Control of the bypass valve «A» of the engine coolant |
Circuit Short to Battery Voltage |
|
P268113 |
Control of the bypass valve «A» of the engine coolant |
Open circuit |
|
P269711 |
Injection Fuel Injector «A» |
Short to ground |
|
P269713 |
Injection Fuel Injector «A» |
Open circuit |
|
P269773 |
Injection Fuel Injector «A» |
The actuator jammed in the closed position |
|
P26977A |
Injection Fuel Injector «A» |
Fluid leakage or seal failure |
|
P2A1612 |
Control unit «D» fuel flow meter injection pump (cam / rotor / nozzle) |
Circuit Short to Battery Voltage |
|
P2A1614 |
Control unit «D» fuel flow meter injection pump (cam / rotor / nozzle) |
Short to ground or open |
|
P2A1692 |
Control unit «D» fuel flow meter injection pump (cam / rotor / nozzle) |
Characteristics or malfunctioning |
|
P2A1E12 |
Control unit «F» fuel flow meter injection pump (cam / rotor / injector) |
Circuit Short to Battery Voltage |
|
P2A1E14 |
Control unit «F» fuel flow meter injection pump (cam / rotor / injector) |
Short to ground or open |
|
P2A1E92 |
Control unit «F» fuel flow meter injection pump (cam / rotor / injector) |
Characteristics or malfunctioning |
|
U000188 |
CAN Backbone bus 2 communication network |
Bus Off |
|
U001088 |
CAN Backbone bus 1 of the communication network |
Bus Off |
|
U008088 |
Communication Subnet of the car engine |
Bus Off |
|
U010100 |
Lost Communication With TECU |
No subtype information |
|
U010A00 |
Lost communication with the A module of the exhaust gas recirculation system |
No subtype information |
|
U010C00 |
The communication with the turbocharger / supercharger control module is broken |
No subtype information |
|
U012100 |
The communication with the anti-lock braking system (ABS) |
No subtype information |
|
U012900 |
Lost Communication With Brake Control Module |
No subtype information |
|
U014100 |
Lost connection with VMCU |
No subtype information |
|
U014200 |
Lost connection with the body control module «B» |
No subtype information |
|
U015500 |
Communication with the instrument cluster control module (IPC) is broken |
No subtype information |
|
U016700 |
Lost communication with the car immobilizer control module |
No subtype information |
|
U029D00 |
Communication with NOx sensor «A» is broken |
No subtype information |
|
U029E00 |
The communication with the NOx sensor «B» is broken |
No subtype information |
|
U032300 |
Software incompatibility with the dashboard control module |
No subtype information |
|
U033100 |
Incompatibility of software with the bodywork control module «A» |
No subtype information |
|
U042600 |
From the immobilizer control module of the car, unreliable data |
No subtype information |
|
U116600 |
Lost communication with CIOM |
No subtype information |
|
U116900 |
Lost connection with DACU |
No subtype information |
|
U116B00 |
Communication with TCM on the high-speed communication bus CAN |
No subtype information |
|
U116C00 |
Communication with TCM on the CAN bus of the power plant is broken |
No subtype information |
|
U116F00 |
Communication with the control module of the supply of the reducing agent via the engine subnetwork is broken |
No subtype information |
|
U117100 |
The communication with the control unit of the body equipment via the high-speed communication bus CAN |
No subtype information |
|
U117300 |
The communication with the IPC control unit via the high-speed communication CAN |
No subtype information |
|
U117888 |
CAN bus communication system bus |
Bus Off |
|
U1FFF68 |
Factory mode active |
Event details |
|
U300001 |
Electronic control module |
General electrical fault |
|
U300041 |
Electronic control module |
Total checksum error |
|
U300044 |
Electronic control module |
Data memory failure |
|
U300045 |
Electronic control module |
Failure of program memory |
|
U300049 |
Electronic control module |
Internal failure of electronics |
|
U300257 |
Vehicle Identification Number |
Invalid / incompatible software component |
————————————————————————————————————————————————————————————
U000188
CAN bus off
Bus off
CAN communication interrupted.
Communication bus is short circuited to ground or battery, or there are connector or harness
problems.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and other ECUs on Backbone 2.
CAN Communication Backbone 2 Net
————————————————————————————————————————————————————————————
U001088
CAN bus off
Bus off
CAN communication interrupted.
Communication bus is short circuited to ground or battery, or there are connector or harness
problems.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and other ECUs on Backbone 1.
CAN Communication Backbone 1 Net
————————————————————————————————————————————————————————————
U004688
CAN bus off
Bus off
CAN communication interrupted.
Communication bus is short circuited to ground or battery, or there are connector or harness
problems.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and other ECUs on Infotainment Net.
CAN Communication Infotainment Net
————————————————————————————————————————————————————————————
U200A88
CAN bus off
Bus off
CAN communication interrupted.
Communication bus is short circuited to ground or battery, or there are connector or harness
problems.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and other ECUs on Display Net.
CAN Communication Display Net
————————————————————————————————————————————————————————————
U300041
CRC checksum occured
General Checksum Failure
Reset of Electronic Control Unit, HMIIOM
Multiple possible root causes e.g. flash error, EMC
problem
Diagnostic Service 14. No additional action is needed.
1. Reprogram ECU.
2. Replace ECU.
Electronic control unit
————————————————————————————————————————————————————————————
U300044
RAM check failed
Data Memory Failure
Reset of Electronic Control
Unit, HMIIOM
ECU hardware error
Diagnostic Service 14. No additional
action is needed.
1. Reprogram ECU.
2. Replace ECU.
Electronic control unit
————————————————————————————————————————————————————————————
U300045
NVRAM/ROM check failed
Program Memory Failure
Reset of Electronic Control Unit, HMIIOM
ECU hardware error
Diagnostic Service 14. No additional action is needed.
1. Reprogram ECU.
2. Replace ECU.
Electronic control unit
————————————————————————————————————————————————————————————
U300046
EEPROM check failed
Calibration / Parameter Memory Failure
Reset of Electronic Control Unit, HMIIOM
ECU hardware error
Diagnostic Service 14. No additional action is needed.
1. Reprogram ECU.
2. Replace ECU.
Electronic control unit
————————————————————————————————————————————————————————————
U300049
ECU Internal failure
Internal Electronic
Failure
Reset of Electronic Control
Unit, HMIIOM
ECU hardware error
Diagnostic Service 14. No additional
action is needed.
1. Reprogram ECU.
2. Replace ECU.
Electronic control unit
————————————————————————————————————————————————————————————
U30004A
Slave Module on wrong LIN channel
Incorrect Component Installed
Reset of Electronic Control Unit, HMIIOM
Wrong LIN slave Module or not correct connected
Diagnostic Service 14. No additional action is needed.
Check that the correct LIN-slaves are connected and that they are connected on the correct channels.
Electronic control unit
————————————————————————————————————————————————————————————
U30004B
ECU temperature is above 85ºC
Over Temperature
Reset of Electronic Control Unit, HMIIOM
1. Environment temperature above normal operating range (-40 °C – 85
°C)
2. ECU damaged
Diagnostic Service 14. No additional action is needed.
1. Check ECU environment
2. Replace ECU if fault is still present when environment temperature is in nomral range
Electronic control unit
————————————————————————————————————————————————————————————
U300094
Unexpected operation detected
Unexpected Operation
Reset of Electronic Control Unit, HMIIOM
SW Application error ( Watch dog failure et.c)
Diagnostic Service 14. No additional action is needed.
1. Reprogram ECU.
2. Replace ECU.
Electronic control unit
————————————————————————————————————————————————————————————
U300316
Voltage < 8 V +- 10%
Circuit Voltage Below Threshold
None
1. Drained battery
2. Power supply system failure
Diagnostic Service 14. No additional action is needed.
Check battery status.
Battery Power
————————————————————————————————————————————————————————————
U300317
Voltage > 32V +- 10%
Circuit Voltage Above Threshold
None
1. Drained battery
2. Power supply system failure
Diagnostic Service 14. No additional action is needed.
Check battery status.
Battery Power
————————————————————————————————————————————————————————————
U1FFF68
Truck is in Factory
Mode
Event Information
None
Truck is in Factory Mode
Diagnostic Service 14. No additional
action is needed.
Set P1C54 to FALSE
Factory Mode Active
————————————————————————————————————————————————————————————
U1FE049
LIN related HW fault detected.
Internal Electronic Failure
LIN communication interrupted.
ECU hardware error.
Diagnostic Service 14. No additional action is needed.
Replace ECU.
ECU LIN Hardware
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U114300
Signal from BBM missing
No Sub Type Information
BBM diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and BBM. If this is the only lost communication DTC then fault is more probable to be close to the BBM.
This fault can also appear by incorrect calibration.
Lost Communication With BBM
————————————————————————————————————————————————————————————
U114400
Signal from RCIOM missing
No Sub Type Information
RCIOM diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 911 and D-950. It can be triggered at the same time as: U014000, U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and RCIOM. If this is the only lost communication DTC then fault is more probable to be close to the RCIOM.
This fault can also appear by incorrect calibration.
Lost Communication With RCIOM
————————————————————————————————————————————————————————————
U114500
Signal from CCIOM missing
No Sub Type Information
CCIOM diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 911 and D-950. It can be triggered at the same time as: U014000, U300316 and 300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and CCIOM. If this is the only lost communication DTC then fault is more probable to be close to the CCIOM.
This fault can also appear by incorrect calibration.
Lost Communication With CCIOM
————————————————————————————————————————————————————————————
U114600
Signal from DACU missing
No Sub Type Information
DACU diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and DACU. If this is the only lost communication DTC then fault is more probable to be close to the DACU.
This fault can also appear by incorrect calibration.
Lost Communication With DACU
————————————————————————————————————————————————————————————
U010000
Signal from EMS missing
No Sub Type Information
EMS diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and EMS. If this is the only lost communication DTC then fault is more probable to be close to the EMS.
This fault can also appear by incorrect calibration.
Lost Communication with EMS
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U010100
Signal from TECU missing
No Sub Type Information
TECU diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and TECU. If this is the only lost communication DTC then fault is more probable to be close to the TECU.
This fault can also appear by incorrect calibration.
Lost Communication with TECU
————————————————————————————————————————————————————————————
U014000
Signal from VMCU missing
No Sub Type Information
VMCU diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and VMCU. If this is the only lost communication DTC then fault is more probable to be close to the VMCU.
This fault can also appear by incorrect calibration.
Lost Communication With VMCU
————————————————————————————————————————————————————————————
U114000
Signal from APM missing
No Sub Type Information
APM diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 911 and D-950. It can be triggered at the same time as: U014000, U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and APM. If this is the only lost communication DTC then fault is more probable to be close to the APM.
This fault can also appear by incorrect calibration.
Lost Communication With APM
————————————————————————————————————————————————————————————
U109F00
Signal from IC missing
No Sub Type Information
IC diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and IC. If this is the only lost communication DTC then fault is more probable to be close to the IC.
This fault can also appear by incorrect calibration.
Lost Communication With IC
————————————————————————————————————————————————————————————
U10A500
Signal from SID missing
No Sub Type Information
SIDH diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and SIDH. If this is the only lost communication DTC then fault is more probable to be close to the SIDH.
This fault can also appear by incorrect calibration.
Lost Communication With SID
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U10A700
Signal from FCIOM missing
No Sub Type Information
FCIOM diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 911 and D-950. It can be triggered at the same time as: U014000, U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and FCIOM. If this is the only lost communication DTC then fault is more probable to be close to the FCIOM.
This fault can also appear by incorrect calibration.
Lost Communication With FCIOM
————————————————————————————————————————————————————————————
U10AB00
Signal from CCM missing
No Sub Type Information
CCM diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 911 and D-950. It can be triggered at the same time as: U10B200, U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and CCM. If this is the only lost communication DTC then fault is more probable to be close to the CCM.
This fault can also appear by incorrect calibration.
Lost Communication With CCM
————————————————————————————————————————————————————————————
U10AC00
Signal from DDM missing
No Sub Type Information
DDM diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 911 and D-950. It can be triggered at the same time as: U10B200, U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and DDM. If this is the only lost communication DTC then fault is more probable to be close to the DDM.
This fault can also appear by incorrect calibration.
Lost Communication With DDM
————————————————————————————————————————————————————————————
U10AD00
Signal from FAS missing
No Sub Type Information
FAS diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 911 and D-950. It can be triggered at the same time as: U014000, U300316 and 300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and FAS. If this is the only lost communication DTC then fault is more probable to be close to the FAS.
This fault can also appear by incorrect calibration.
Lost Communication With FAS
————————————————————————————————————————————————————————————
U10AE00
Signal from Alarm missing
No Sub Type Information
Alarm diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 911 and D-950. It can be triggered at the same time as: U10B200, U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and Alarm. If this is the only lost communication DTC then fault is more probable to be close to the Alarm.
This fault can also appear by incorrect calibration.
Lost Communication With Alarm
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U10AF00
Signal from PDM missing
No Sub Type Information
PDM diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 911 and D-950. It can be triggered at the same time as: U10B200, U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and PDM. If this is the only lost communication DTC then fault is more probable to be close to the PDM.
This fault can also appear by incorrect calibration.
Lost Communication With PDM
————————————————————————————————————————————————————————————
U10B000
Signal from SRS missing
No Sub Type Information
SRS diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 911 and D-950. It can be triggered at the same time as: U10B200, U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and SRS. If this is the only lost communication DTC then fault is more probable to be close to the SRS.
This fault can also appear by incorrect calibration.
Lost Communication With SRS
————————————————————————————————————————————————————————————
U10B100
Signal from TPM missing
No Sub Type Information
TPM diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and TPM. If this is the only lost communication DTC then fault is more probable to be close to the TPM.
This fault can also appear by incorrect calibration.
Lost Communication With TPM
————————————————————————————————————————————————————————————
U10B200
Signal from CIOM missing
No Sub Type Information
CIOM diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and CIOM. If this is the only lost communication DTC then fault is more probable to be close to the CIOM.
This fault can also appear by incorrect calibration.
Lost Communication With CIOM
————————————————————————————————————————————————————————————
U10B400
Signal from LECM missing
No Sub Type Information
LECM diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 911 and D-950. It can be triggered at the same time as: U10B200 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and LECM. If this is the only lost communication DTC then fault is more probable to be close to the LECM.
This fault can also appear by incorrect calibration.
Lost Communication With LECM
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U10B600
Signal from Audio missing
No Sub Type Information
Audio diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and Audio. If this is the only lost communication DTC then fault is more probable to be close to the Audio.
This fault can also appear by incorrect calibration.
Lost Communication With Audio
————————————————————————————————————————————————————————————
U10B800
Signal from VS missing
No Sub Type Information
VS diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and VS. If this is the only lost communication DTC then fault is more probable to be close to the VS.
This fault can also appear by incorrect calibration.
Lost Communication With VS
————————————————————————————————————————————————————————————
U114200
Signal from TGW2 missing
No Sub Type Information
TGW2 diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and TGW2. If this is the only lost communication DTC then fault is more probable to be close to the TGW2.
This fault can also appear by incorrect calibration.
Lost Communication With TGW2
————————————————————————————————————————————————————————————
U115900
Signal from EAS missing
No Sub Type Information
EAS diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and EAS. If this is the only lost communication DTC then fault is more probable to be close to the EAS.
This fault can also appear by incorrect calibration.
Lost Communication With EAS – Extra Axle Steering
————————————————————————————————————————————————————————————
U010E00
Signal from ACM missing
No Sub Type Information
Aftertreatment Control Module diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and ACM. If this is the only lost communication DTC then fault is more probable to be close to the ACM.
This fault can also appear by incorrect calibration.
Lost Communication With Reductant Control Module
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U114E00
Signal from Tachograph missing
No Sub Type Information
Tachograph diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and Tachograph. If this is the only lost communication DTC then fault is more probable to be close to the Tachograph.
This fault can also appear by incorrect calibration.
Lost Communication With Tachograph
————————————————————————————————————————————————————————————
U012900
Signal from Brake system control module missing
No Sub Type Information
Wire Brake System diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and Brake system. If this is the only lost communication DTC then fault is more probable to be close to the Brake system.
This fault can also appear by incorrect calibration.
Lost Communication With Brake System Control Module
————————————————————————————————————————————————————————————
U114F00
Signal from BLECU missing
No Sub Type Information
Bending Light diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 911 and D-950. It can be triggered at the same time as: U014000, U10A700, U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and BLECU. If this is the only lost communication DTC then fault is more probable to be close to the BLECU.
This fault can also appear by incorrect calibration.
Lost Communication With Bending Light ECU
————————————————————————————————————————————————————————————
U115000
Signal from FLS missing
No Sub Type Information
Forward Looking Sensor diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 911 and D-950. It can be triggered at the same time as: U114600, U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and FLS. If this is the only lost communication DTC then fault is more probable to be close to the FLS.
This fault can also appear by incorrect calibration.
Lost Communication With Forward Looking Sensor
————————————————————————————————————————————————————————————
U115100
Signal from LPOS missing
No Sub Type Information
Lane Position diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 911 and D-950. It can be triggered at the same time as: U114600, U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and LPOS. If this is the only lost communication DTC then fault is more probable to be close to the LPOS.
This fault can also appear by incorrect calibration.
Lost Communication With Lane Position Object Control Unit
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U115200
Signal from WRC missing
No Sub Type Information
Wireless Remote Control diagnostic warnings and functional messages affected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 911 and D-950. It can be triggered at the same time as: U10B200, U300316 and U300317.
Connector or harness problems.
Problem with sending ECU.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and WRC. If this is the only lost communication DTC then fault is more probable to be close to the WRC.
This fault can also appear by incorrect calibration.
Lost Communication With Wireless Remote Control System
————————————————————————————————————————————————————————————
U115500
Max number of DTC:s within the
system reached.
No Sub Type Information
No more DTC can be set after this DTC is set.
Reception of 29 DTCs will trigger the setting of this
DTC.
Diagnostic Service 14. No additional action is needed.
Control other set DTCs. When they are erased this DTC should also be erased.
DTC Notification Max Limit Reached
————————————————————————————————————————————————————————————
U115600
TIPSI (The
Astonishing Tribe (TAT) Inter Process Software Interface
) hearbeat signalling is missing or other TIPSI related transport errors occur.
No Sub Type Information
Driver Information Display will stop working.
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
Software error, software mismatch between HMIIOM and IC or communication problems.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between HMIIOM and IC. Also check that the software versions match.
Driver Information Display
————————————————————————————————————————————————————————————
U115694
TIPSI (The
Astonishing Tribe (TAT) Inter Process Software Interface
) memory allocation error occur.
Unexpected Operation
Driver Information Display resets
Software Error
Diagnostic Service 14. No additional action is needed.
Reprogram HMIIOM or IC.
Driver Information Display
————————————————————————————————————————————————————————————
U115700
TIPSI (The
Astonishing Tribe (TAT) Inter Process Software Interface) hearbeat signalling is missing or other TIPSI related transport errors occur.
No Sub Type Information
Secondary Information Display will stop working.
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
Software error, software mismatch between HMIIOM and IC or communication problems.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between HMIIOM and IC. Also check that the software versions match.
Secondary Information Display
————————————————————————————————————————————————————————————
U115794
TIPSI (The
Astonishing Tribe (TAT) Inter Process Software Interface) memory allocation error occur.
Unexpected Operation
Secondary Information Display resets
Software Error
Diagnostic Service 14. No additional action is needed.
Reprogram HMIIOM or IC.
Secondary Information Display
————————————————————————————————————————————————————————————
U114D11
LIN transceiver has detected too many transmit or receive errors and pin is short circuited to ground.
Circuit Short To Ground
LIN communication interrupted.
Connector or harness problems
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and LIN nodes on LIN 15.
LIN15 Communication Bus
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U114D12
LIN transceiver has detected too many transmit or receive errors and pin is short circuited to battery.
Circuit Short To Battery
LIN communication interrupted.
Connector or harness problems
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and LIN nodes on LIN 15.
LIN15 Communication Bus
————————————————————————————————————————————————————————————
U114D88
LIN transceiver has detected too many transmit or receive errors.
Bus off
LIN communication interrupted.
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 854. It can be triggered at the same time as: U114D11 and U114D12.
Connector or harness problems
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and LIN nodes on LIN 15.
LIN15 Communication Bus
————————————————————————————————————————————————————————————
U114786
Gear Lever LIN slave Module Invalid Signal
Signal Invalid
GearShift function will be effected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 798. It can be triggered at the same time as:
U114B11, U114B12 and
U114B88.
LIN Slave Module error
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors on between ECU and GLU/DashGSU.
2. Check GLU/DashGSU functionality. If faulty then replace GLU/DashGSU.
Gear Lever LIN Module
————————————————————————————————————————————————————————————
U114787
Gear Lever LIN Module slave not responding
Missing Message
GearShift function will be effected
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 798. It can be triggered at the same time as:
U114B11, U114B12 and
U114B88.
LIN Slave Module error
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors on between ECU and GLU/DashGSU.
2. Check GLU/DashGSU functionality. If faulty then replace GLU/DashGSU.
Gear Lever LIN Module
————————————————————————————————————————————————————————————
U114886
Stalk Module LIN slave Module Invalid
Signal
Signal Invalid
Functions controlled by the Stalk module will be
effected
LIN Slave Module error
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors on between ECU and SM.
2. Check SM functionality. If faulty then replace SM.
Stalk Module LIN Module
————————————————————————————————————————————————————————————
U114887
Stalk Module LIN slave Module not
responding
Missing Message
Functions controlled by the Stalk module will be
effected
LIN Slave Module error
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors on between ECU and SM.
2. Check SM functionality. If faulty then replace SM.
Stalk Module LIN Module
————————————————————————————————————————————————————————————
U114986
Steering Wheel Switch LIN slave Module Invalid
Signal
Signal Invalid
Functions controlled by the Steering Wheel Switch module will be effected
LIN Slave Module error
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors on between ECU and SWS.
2. Check SWS functionality. If faulty then replace SWS.
Steering Wheel Switch LIN Module
————————————————————————————————————————————————————————————
U114987
Steering Wheel Switch LIN slave Module not
responding
Missing Message
Functions controlled by the Steering Wheel Switch module will be effected.
LIN Slave Module error
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors on between ECU and SWS.
2. Check SWS functionality. If faulty then replace SWS.
Steering Wheel Switch LIN Module
————————————————————————————————————————————————————————————
U114A86
Secondary Information Display Control Panel LIN slave Module Invalid Signal
Signal Invalid
Functions related to Display Control Panel will be effected.
LIN Slave Module error
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors on between ECU and SIDCP.
2. Check SIDCP functionality. If faulty then replace SIDCP.
Secondary Information Display Control Panel LIN Module
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U114A87
Secondary Information Display Control Panel LIN slave Module not responding
Missing Message
Functions related to Display Control Panel will be effected
LIN Slave Module error
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors on between ECU and SIDCP.
2. Check SIDCP functionality. If faulty then replace SIDCP.
Secondary Information Display Control Panel LIN Module
————————————————————————————————————————————————————————————
U114B11
LIN transceiver has detected too many transmit or receive errors and pin is short circuited to ground.
Circuit Short To Ground
LIN communication interrupted.
Connector or harness problems
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and LIN nodes on LIN 13.
LIN13 Communication Bus
————————————————————————————————————————————————————————————
U114B12
LIN transceiver has detected too many transmit or receive errors and pin is short circuited to battery.
Circuit Short To Battery
LIN communication interrupted.
Connector or harness problems
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and LIN nodes on LIN 13.
LIN13 Communication Bus
————————————————————————————————————————————————————————————
U114B88
LIN transceiver has detected too many transmit or receive errors.
Bus off
LIN communication interrupted.
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 854. It can be triggered at the same time as: U114B11 and U114B12.
Connector or harness problems
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors between ECU and LIN nodes on LIN 13.
2. Replace HMIIOM ECU.
LIN13 Communication Bus
————————————————————————————————————————————————————————————
U114C11
LIN transceiver has detected too many transmit or receive errors and pin is short circuited to ground.
Circuit Short To Ground
LIN communication interrupted.
Connector or harness problems
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and LIN nodes on LIN 14.
LIN14 Communication Bus
————————————————————————————————————————————————————————————
U114C12
LIN transceiver has detected too many transmit or receive errors and pin is short circuited to battery.
Circuit Short To Battery
LIN communication interrupted.
Connector or harness problems
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and LIN nodes on LIN 14.
LIN14 Communication Bus
————————————————————————————————————————————————————————————
U114C88
LIN transceiver has detected too many transmit or receive errors.
Bus off
LIN communication interrupted.
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 854. It can be triggered at the same time as: U114C11 and U114C12.
Connector or harness problems
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and LIN nodes on LIN 14.
LIN14 Communication Bus
————————————————————————————————————————————————————————————
B150216
Voltage < 8V
Circuit Voltage Below Threshold
Gear shifting functionality stops to work.
1. Connecter or harness problems.
2. GLU or HMIIOM
damaged.
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors between ECU and GLU.
2. Check output voltage from ECU to GLU.
Gear Lever Unit
————————————————————————————————————————————————————————————
B150217
Voltage > 18V
Circuit Voltage Above Threshold
Gear shifting functionality stops to work.
1. Connecter or harness problems.
2. GLU or HMIIOM
damaged.
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors between ECU and GLU.
2. Check output voltage from ECU to GLU.
Gear Lever Unit
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
B150249
Sensor fault
detected.
Internal Electronic
Failure
Gear position will be set to
last reliable position.
Faulty sensors or lever stuck
Diagnostic Service 14. No additional
action is needed.
Replace GLU.
Gear Lever Unit
————————————————————————————————————————————————————————————
B150294
Both up and down shift button activation simultaneously
Unexpected Operation
Gear position will be set to last reliable position.
Unexpected Operation
Diagnostic Service 14. No additional action is needed.
Replace GLU.
Gear Lever Unit
————————————————————————————————————————————————————————————
B150716
Voltage < 7 V
Circuit Voltage Below Threshold
LIN is switched off. SIDCP will not work.
1. Connecter or harness problems.
2. SIDCP or HMIIOM
damaged.
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors between ECU and SIDCP.
2. Check output voltage from ECU to SIDCP.
Secondary Information Display Control Panel
————————————————————————————————————————————————————————————
B150717
Voltage > 20 V
Circuit Voltage Above Threshold
LIN is switched off. SIDCP will not work.
1. Connecter or harness problems.
2. SIDCP or HMIIOM
damaged.
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors between ECU and SIDCP.
2. Check output voltage from ECU to SIDCP.
Secondary Information Display Control Panel
————————————————————————————————————————————————————————————
B150744
RAM error, read compare failure after write
operation.
Data Memory Failure
ECU resets continuously. DTC will never be set.
Memory failure
Diagnostic Service 14. No additional action is needed.
Replace SIDCP
Secondary Information Display Control Panel
————————————————————————————————————————————————————————————
B150745
ROM error, 16 bit checksum incorrect
Program Memory Failure
ECU resets continuously. DTC will never be set.
Memory failure
Diagnostic Service 14. No additional action is needed.
Replace SIDCP
Secondary Information Display Control Panel
————————————————————————————————————————————————————————————
B150746
EEPROM checksum error
Calibration / Parameter Memory Failure
ECU resets continuously. DTC will never be set.
Memory failure
Diagnostic Service 14. No additional action is needed.
Replace SIDCP
Secondary Information Display Control Panel
————————————————————————————————————————————————————————————
B150794
Watchdog error read from reset register
Unexpected Operation
ECU resets continuously. DTC will never be set.
Watchdog failure
Diagnostic Service 14. No additional action is needed.
Replace SIDCP
Secondary Information Display Control Panel
————————————————————————————————————————————————————————————
B150311
Input Signals of Brake Program Button <= 2,44 V OR Rain Sensor Button
<= 0,88 V OR Scroll Wheel <= 0,88 V
Circuit Short To Ground
It will not be possible to activate on or more of the following functions: Brake Program, Rain Sensor and/or use wipers.
Brake program button, rain sensor button or scroll wheel short circuit to ground.
Diagnostic Service 14. No additional action is needed.
Manual Check of Brake Program Button, Rainsensor Button and Scroll Wheel. Replace Stalk with erroneous function.
Stalk Module Variant 1
————————————————————————————————————————————————————————————
B150312
Input Signals of Brake Program Button >= 4,5 V OR Rain Sensor Button
>= 4,78 V OR Scroll Wheel >= 4,88 V
Circuit Short To Battery
It will not be possible to activate on or more of the following functions: Brake Program, Rain Sensor and/or use wipers.
Brake program button, rain sensor button or scroll wheel short circuit to battery.
Diagnostic Service 14. No additional action is needed.
Manual Check of Brake Program Button, Rainsensor Button and Scroll Wheel. Replace Stalk with erroneous function.
Stalk Module Variant 1
————————————————————————————————————————————————————————————
B150313
Open circuit conditions detected on Rain Sensor button OR Scroll
Wheel.
Circuit Open
It will not be possible to activate on or more of the following functions: Rain Sensor and/or use wipers.
Rain sensor button or scroll wheel has an open circuit.
Diagnostic Service 14. No additional action is needed.
Manual Check of Rainsensor Button and Scroll Wheel. Replace Stalk with erroneous function.
Stalk Module Variant 1
————————————————————————————————————————————————————————————
B150316
Voltage < 8V
Circuit Voltage Below Threshold
LIN communicastion Interface shut down.
1. Connecter or harness problems.
2. SM1 or HMIIOM
damaged.
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors between ECU and SM1.
2. Check output voltage from ECU to SM1.
Stalk Module Variant 1
————————————————————————————————————————————————————————————
B150317
Voltage > 18V
Circuit Voltage Above Threshold
LIN communicastion Interface shut down.
1. Connecter or harness problems.
2. SM1 or HMIIOM
damaged.
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors between ECU and SM1.
2. Check output voltage from ECU to SM1.
Stalk Module Variant 1
————————————————————————————————————————————————————————————
B15031C
Voltage < 2.1 V
Circuit Voltage Out of Range
None
1. Connecter or harness problems.
2. SM1 or HMIIOM
damaged.
Diagnostic Service 14. No additional action is needed.
No action required.
Stalk Module Variant 1
————————————————————————————————————————————————————————————
B150344
RAM Failure
Data Memory Failure
LIN communication
Interface shut down.
Memory failure
Diagnostic Service 14. No additional
action is needed.
Replace base plate of SM1.
Stalk Module Variant 1
————————————————————————————————————————————————————————————
B150345
ROM Failure
Program Memory
Failure
LIN communication
Interface shut down.
Memory failure
Diagnostic Service 14. No additional
action is needed.
Replace base plate of SM1.
Stalk Module Variant 1
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
B150346
EEPROM failure
Calibration / Parameter Memory Failure
LIN communication Interface shut down.
Memory failure
Diagnostic Service 14. No additional action is needed.
Replace base plate of SM1.
Stalk Module Variant 1
————————————————————————————————————————————————————————————
B15034A
Incorrect Component detected
Incorrect Component Installed
It will not be possible to activate on or more of the following functions: Direction Indicators, Main Beam, Washers and Wipers and/or Retarder.
Direction Indicator stalk, washer wiper stalk or auxiliary stalk incorrectly mounted or damaged.
Diagnostic Service 14. No additional action is needed.
Check correct mountig of each Stalk.
Stalk Module Variant 1
————————————————————————————————————————————————————————————
B150364
Scroll Wheel Unplausible Signal
Signal Plausibility Failure
It will not be possible to activate the wipers
manually.
Scroll Wheel damaged.
Diagnostic Service 14. No additional action is needed.
Replace washer wiper stalk.
Stalk Module Variant 1
————————————————————————————————————————————————————————————
B150394
Watchdog Reset
Unexpected Operation
None
Watchdog failure
Diagnostic Service 14. No additional
action is needed.
Replace base plate of SM1.
Stalk Module Variant 1
————————————————————————————————————————————————————————————
B150395
Detected to low input voltage from direction indicator stalk, washer wiper stalk or auxiliary stalk.
Incorrect Assembly
It will not be possible to activate on or more of the following functions: Direction Indicators, Main Beam, Washers and Wipers and/or Retarder.
Direction Indicator stalk, washer wiper stalk or auxiliary stalk dismounted.
Diagnostic Service 14. No additional action is needed.
Check correct mountig of each Stalk. Replace uncorrect mounted or damaged Stalk.
Stalk Module Variant 1
————————————————————————————————————————————————————————————
B150416
Voltage < 7 volts +- 8%
Circuit Voltage Below Threshold
None
1. Connecter or harness problems.
2. SM2 or HMIIOM
damaged.
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors between ECU and SM2.
2. Check output voltage from ECU to SM2.
Stalk Module Variant 2
————————————————————————————————————————————————————————————
B150417
Voltage > 18 volts +- 8%
Circuit Voltage Above Threshold
None
1. Connecter or harness problems.
2. SM2 or HMIIOM
damaged.
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors between ECU and SM2.
2. Check output voltage from ECU to SM2.
Stalk Module Variant 2
————————————————————————————————————————————————————————————
B150444
RAM Error. read compare failure after write operation.
Data Memory Failure
RAM DATA is untrustable, may affect functionality related to SM2. What it affects depends on where in RAM error occured.
Memory failure
Diagnostic Service 14. No additional action is needed.
Replace SM2.
Stalk Module Variant 2
————————————————————————————————————————————————————————————
B150446
EEPROM checksum error.
Calibration / Parameter Memory Failure
EEPROM DATA is
untrustable, may affect functionality related to SM2. What it affects depends on where in EEPROM error occured.
Memory failure
Diagnostic Service 14. No additional action is needed.
Replace SM2.
Stalk Module Variant 2
————————————————————————————————————————————————————————————
B150494
Watchdog error read from reset register
Unexpected Operation
Functionality related to SM2 will not work.
Watchdog failure
Diagnostic Service 14. No additional action is needed.
Replace SM2.
Stalk Module Variant 2
————————————————————————————————————————————————————————————
B150516
Voltage < 7 volts
Circuit Voltage Below Threshold
LIN is switched off
1. Connecter or harness problems.
2. SWS1 or HMIIOM
damaged.
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors between ECU and SWS1.
2. Check output voltage from ECU to SWS1.
Steering Wheel Switch Variant 1
————————————————————————————————————————————————————————————
B150517
Voltage > 20 volts
Circuit Voltage Above Threshold
LIN is switched off LEDs are switched off
1. Connecter or harness problems.
2. SWS1 or HMIIOM
damaged.
Diagnostic Service 14. No additional action is needed.
1. Check wires and connectors between ECU and SWS1.
2. Check output voltage from ECU to SWS1.
Steering Wheel Switch Variant 1
————————————————————————————————————————————————————————————
B150544
RAM error, read compare failure after write
operation.
Data Memory Failure
ECU resets continuously. DTC will never be set.
Memory failure
Diagnostic Service 14. No additional action is needed.
Replace SWS1.
Steering Wheel Switch Variant 1
————————————————————————————————————————————————————————————
B150545
ROM error, 16 bit checksum incorrect.
Program Memory Failure
ECU resets continuously. DTC will never be set.
Memory failure
Diagnostic Service 14. No additional action is needed.
Replace SWS1.
Steering Wheel Switch Variant 1
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
B150546
EEPROM checksum error.
Calibration / Parameter Memory Failure
ECU resets continuously. DTC will never be set.
Memory failure
Diagnostic Service 14. No additional action is needed.
Replace SWS1.
Steering Wheel Switch Variant 1
————————————————————————————————————————————————————————————
B150584
One or several SWS buttons or scroll wheels short circuit to ground.
Signal Below Allowable Range
Reduced functionality for the right steering wheel switch. Possible that switches are not useable.
Short to ground
Diagnostic Service 14. No additional action is needed.
1. Check connection to left SWS1
2. Replace SWS1 if fault is still present
Steering Wheel Switch Variant 1
————————————————————————————————————————————————————————————
B150585
One or several SWS buttons or scroll wheels short circuit to battery or open circuit.
Signal Above Allowable Range
Reduced functionality for the right steering wheel switch. Possible that switches are not useable.
Short to battery or open circuit
Diagnostic Service 14. No additional action is needed.
1. Check connection to left SWS1
2. Replace SWS1 if fault is still present
Steering Wheel Switch Variant 1
————————————————————————————————————————————————————————————
B150594
Watchdog error read from reset register
Unexpected Operation
ECU resets continuously. DTC will never be set.
Watchdog failure
Diagnostic Service 14. No additional action is needed.
Replace SWS1.
Steering Wheel Switch Variant 1
————————————————————————————————————————————————————————————
B150611
Voltage = 0V
Circuit Short To Ground
Cruise Control functionality will be effected
Connection between right SWS buttons and left SWS buttons short circuited to
ground.
Diagnostic Service 14. No additional action is needed.
1. Check connection between left hand side and right hand side of SWS2.
2. Replace SWS2.
Steering Wheel Switch Variant 2
————————————————————————————————————————————————————————————
B150616
Voltage < 7V +- 10%
Circuit Voltage Below Threshold
SWS buttons may not work.
1. Connecter or harness problems.
2. SWS2 or HMIIOM
damaged.
Diagnostic Service 14. No additional action is needed.
1. Check output voltage from HMIIOM to SWS2.
2. Replace SWS2
Steering Wheel Switch Variant 2
————————————————————————————————————————————————————————————
B150617
Voltage > 19V +- 10%
Circuit Voltage Above Threshold
SWS buttons may not work.
1. Connecter or harness problems.
2. SWS2 or HMIIOM
damaged.
Diagnostic Service 14. No additional action is needed.
1. Check output voltage from HMIIOM to SWS2.
2. Replace SWS2
Steering Wheel Switch Variant 2
————————————————————————————————————————————————————————————
B150694
MCU watchdog reset
Unexpected Operation
SWS2 resets
Watchdog failure
Diagnostic Service 14. No additional action is needed.
Replace SWS2.
Steering Wheel Switch Variant 2
————————————————————————————————————————————————————————————
B15084A
Incorrect Gearbox Stalk detected
Incorrect Component Installed
Gearshifting functionality will be effected
Incorrect Gearbox Stalk installed or wrong
configuration
Diagnostic Service 14. No additional action is needed.
Control that the correct gearbox stalk is installed if the truck should have a gearbox stalk.
Gearbox Stalk
————————————————————————————————————————————————————————————
B15094A
Incorrect Radio Satelite Stalk
detected
Incorrect Component Installed
Audio functionality will be effected
Incorrect Radio Satelite Stalk installed or wrong
configuration
Diagnostic Service 14. No additional action is needed.
Control that the correct radio satellite stalk is installed if the truck should have a radio satellite stalk.
Radio Satelite Stalk
————————————————————————————————————————————————————————————
B150A4A
Incorrect Retarder Stalk detected
Incorrect Component Installed
Auxiliary brakes will be effected
Incorrect Retarder Stalk installed or wrong
configuration
Diagnostic Service 14. No additional action is needed.
Control that the correct retarder stalk is installed if the truck should have a retarder stalk.
Retarder Stalk
————————————————————————————————————————————————————————————
B150B4A
Incorrect cruise
control switch detected
Incorrect Component Installed
Cruise Control functionality will be effected
Incorrect cruise control
switch installed or wrong configuration
Diagnostic Service 14. No additional action is needed.
Control that the correct speed control switches are installed if the truck should have speed control switches.
Cruise Control Switches
————————————————————————————————————————————————————————————
B150C4A
Incorrect phone control switch detected
Incorrect Component Installed
Will not be possible to naviage in menus and phone functionality will be
effected
Incorrect phone control switch installed or wrong configuration
Diagnostic Service 14. No additional action is needed.
Control that the correct phone control switches are installed if the truck should have phone control switches.
Phone Control Switches
————————————————————————————————————————————————————————————
B150D11
Voltage = 0V
Circuit Short To Ground
LIN communication
interrupted.
-Main connector pin 8 short
circuit to ground.
Diagnostic Service 14. No additional
action is needed.
Check wires and connectors between ECU and other ECUs on LIN 13.
LIN13 Power Supply
Circuit
————————————————————————————————————————————————————————————
B150D17
VP_LINA > 14V (VP_LINA_MON <
2,54)
Circuit Voltage Above Threshold
LIN communication interrupted.
Connector or harness problems
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and other ECUs on LIN 13.
LIN13 Power Supply Circuit
————————————————————————————————————————————————————————————
B150E11
Voltage = 0V
Circuit Short To Ground
LIN communication
interrupted.
-Main connector pin 9 short
circuit to ground.
Diagnostic Service 14. No additional
action is needed.
Check wires and connectors between ECU and other ECUs on LIN 14.
LIN14 Power Supply
Circuit
————————————————————————————————————————————————————————————
B150E17
VP_LINB > 14V (VP_LINB_MON < 2,54)
Circuit Voltage Above Threshold
LIN communication interrupted.
Connector or harness problems
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and other ECUs on LIN 14.
LIN14 Power Supply Circuit
————————————————————————————————————————————————————————————
B150F11
Voltage = 0V
Circuit Short To Ground
LIN communication interrupted.
-Main connector pin 10 short circuit to ground.
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and other ECUs on LIN 15.
LIN15 Power Supply Circuit
————————————————————————————————————————————————————————————
B150F17
VP_LINC > 14V (VP_LINC_MON <
2,54)
Circuit Voltage Above Threshold
LIN communication interrupted.
Connector or harness problems
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and other ECUs on LIN 15.
LIN15 Power Supply Circuit
Node
DTC ISO
FailureEvent
FTB_Name
FunctBehaviorDesc
PossibleRootCause
ProcedureEraseConfirmedDtc
ProposedWorkshopAction
ProprietaryName
————————————————————————————————————————————————————————————
U115371
Detection that there is a button that is stuck. Button is stuck after 1-4095s, depending on which button is stuck.
Actuator Stuck
Functions will be effected
Button stuck or driver has held button pressed longer than the allowed time
Diagnostic Service 14. No additional action is needed.
Control that GLU, SM, SWS and SIDCP buttons are working as they should.
Softkey and Rocker Buttons
————————————————————————————————————————————————————————————
C100054
Input parameter is missing.
Missing Calibration
Will not be possible to calibrate load for front axle.
Wrong calibration.
Diagnostic Service 14. No additional action is needed.
Correct calibration parameters.
Leaf Calculation Failure
————————————————————————————————————————————————————————————
U200B93
No response from Real Time Clock
No Operation
Clock may show incorrect time. Alarm clock, parking heater and refrigerator timer will not work.
Internal HW fault
Diagnostic Service 14. No additional action is needed.
Replace HMIIOM.
Real Time Clock (RTC)
————————————————————————————————————————————————————————————
U115A00
Signal from EMS missing
No Sub Type Information
Engine Malfunction Indication telltale will be activated “On steady” at least during current drive cycle
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
“Connector or harness problems.
Data link EMC problems. Problem with sending ECU.”
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and EMS. This fault can also appear by incorrect calibration.
Lost Communication with EMS
————————————————————————————————————————————————————————————
U115B00
Signal from EMS missing
No Sub Type Information
Engine Malfunction Indication telltale will be activated “On steady” at least during current drive cycle
Note: This DTC can be set as a secondary DTC which has been agreed in deviation D- 950. It can be triggered at the same time as: U300316 and U300317.
“Connector or harness problems.
Data link EMC problems. Problem with sending ECU.”
Diagnostic Service 14. No additional action is needed.
Check wires and connectors between ECU and EMS. This fault can also appear by incorrect calibration.
Lost Communication with EMS