Supply ink mimaki ошибка - Решение и исправление самых разных ошибок на TopOshibok.ru

Hi im frm india and …
I bought a Mimaki UV printer 5 months ago and since its install an error popping up «Supply ink :Y______» & sometimes «Supply ink :C______»
And the machine stops until i reboot it again,
an engineer frm mimaki kept trying to resolve this issue by changing its slider board, main board, sub tank n connectors and other settings like updating machine soft ver. & pump pressure settings etc.. for the past 5 months but the machine would work for a day or two and then same error pops up

Can someone help n guide me as to what to do to cure this error permanently? I will be very thankful to you.

It seems to me that your cartridges may be out of date, check the expiry date on them. (printed on the side of the cart) But I would really expect aMimakii engineer to spot that so could be wrong… Have your tried swapping cartridges out?

It seems to me that your cartridges may be out of date, check the expiry date on them. (printed on the side of the cart) But I would really expect aMimakii engineer to spot that so could be wrong… Have your tried swapping cartridges out?

thanks Martin for the reply
i checked the expiry date on the bottles and they’re not expired yet. i’ve swapped the ink bottles but the error still remains, like i said earlier the mimaki engineer couldn’t rectify this issue, so i thought that i’d post here and may be i can get some help. thanks again

I have a Mimaki, but it’s a different model.(JFX200-2513) I sometimes see this message, then I fill the subtank. I don’t know if this is an option for your machine or not, but I thought I would throw it out there anyways. I hit the Function button. Then scroll down to Maintenance, hit enter. Then scroll down to subtank, chose which one you want to fill up, hit enter. Then it says execute, hit enter, and that fills up the subtank and supplies the machine with ink.

Thanks Susan for the reply, yes i’ve tried filling up the subtank and it shows same error while filling up and after that it runs for sometime and the same error pos up and the thing is that only Cyan and Yellow show this error

We had same problem with UJF3042MKII. Tech replace something under the bottle and error disapears. I think it was something like damper.

We had same problem with our UJF with LUS120 inks in bottles. Tech change something like damper inside under the bottle. Error disapears.

Are you getting 61A and 61B errors? Have you tried running “Overflow” in the maintenance menu? Also, I would verify that the float sensors on the ink supply tanks are working properly. The sub tanks above the printheads have built in filters and sensors so verify they are not saturated with ink. You may want to verify negative and positive pressures are set to the recommended settings.

Thanks lubo1972 and L.D for your replies
As for the machine, Mimaki india took the machine to their warehouse (after i threatened them wth legal action) for further testing as to why this error keep popping up even after numerous tech visits failed to resolve it and meanwhile they installed another demo machine at my office so that i could continue my work until the error is 100% rectified on my machine and they’ve asked for a months time to find and resolve this error or else they’d have to replace my machine wth a new one.
And yes L.D i was getting 61A and 61B errors but i didn’t try running overflow in the maintenance menu but i did try to fill ink from menu & it’d give same error during filling up but would also run for sometime without any error after that.
I am also waiting for a in depth report from mimaki as to what was the reason behind this error..
and thanks again for your help guys.

Hi Jashanjeet

I am having the same issue , did you ever find out the problem?

any update abut the solution?

Hey! «Supply ink» mean in the subtank dont have ink. The question ist why… Maybe the machine had a overflow and this make damage the subtank.
Pleas check in the machine information which error the machine had at last days. You can check too the waste pump in test menu if all is correctly.
Check this two point pleas.

hand851

Roland Mutoh & Mimaki inks digiprint-parts.com

Is there any error message with the supply ink message?
Check your positive and negative air.

I’m in at work just now to do routine maintenance in times of covid. The printer was in a crashed state ‘pump sensor fail’. I restarted, did a nozzle check, and barely a single one fired. Turned machine off, back on, then I got this fill ink error. Trying the overflow now…. Fill ink only gives the same error (61b)

Overflow has finished and nothing’s changed. Still says’ supply ink: Y

Ucjv300-160

Try returnt this printer to dealer I mean you cant solve this problem and you need ask help from Service Mimaki. Last printer Mimaki not good I advice you see to Roland side.

The error went away after a restart, and then performed perfectly since… Maybe a brain fart? We’ll see. Otherwise, it’s an impeccable printer. We’ve had it too long to return now anyway

Please did anyone find a solution to ink overflow error??

I have similar issue in UCJV150-160 single head machine.

The positive and negative pressure are with in range and set properly.

The sub tank assy has been replaced.

The level sensor have been cross checked and working fine.

Please assist.

Dis

Please did anyone find a solution to ink overflow error??

I have similar issue in UCJV150-160 single head machine.

The positive and negative pressure are with in range and set properly.

The sub tank assy has been replaced.

The level sensor have been cross checked and working fine.

Please assist.

Did you manage to solve the problem?
Seems this is the common issue in ucjv

Please did anyone find a solution to ink overflow error??

I have similar issue in UCJV150-160 single head machine.

The positive and negative pressure are with in range and set properly.

The sub tank assy has been replaced.

The level sensor have been cross checked and working fine.

Please assist.

hi,
I encounter same issue which the tech change everything from the printhead there all the way to the ink value which is the last item he changed. So many parts all replaced till the ink value then fixed the issue! Actually the sequence should be change the HELL ink value as it contain the metal spring which is the main cause mostly. I made a video which i fix another overflow whichout replacing any new parts. just take out the spring and stretch it replace it back will fix the issue. This will happen in time as there is 8 of the ink value unless u stretch all 8 of the metal spring. The ink is flow out gravity and is stop by the value, once the damper detect overflow it will should close the value. if the spring wearout or not strong enough it will leak and overflow occurs thats my 2 cents view.

Youtube link — Mimaki Error 61A ink Overflow

regards
Ivan

Источник

r/CommercialPrinting

A community for prepress, designers, operators, and lovers of the commercial printing industry. This is not the place for questions about your home printer, local copy shop, or screen printing.
Feel free to discuss: file prep, techniques, opinions, design, and more.

**Spam will be blocked and users banned without warning.**

Members

Online

Источник

Catalog
Sign In
Contacts
Forum
Eng

Error Codes
Mimaki
JFX200-2513
All codes

Error Codes List page 16

Code: 61b
Display: ERROR 61b SUPPLY INK:12345678
Description: Ink filling into the sub-tank has failed.
Remedy: 1.With [#TEST SENSOR], check the detection status of the target liquid level detection sensor. (Also, visually check the float position in the sub-tank.) 2. From [#TEST AGEING] -> [PUMP MOTOR], discharge ink in the sub-tank to the bottom. From [#TEST AGEING] -> [INK SUPPLY], check that sending ink is performed. *If sending ink cannot be performed: The supply pump, the bottle valve and the UISS valve shall be replaced.

Code: 61c
Display: ERROR 61c NEGATIVE P.CONTROL
Description: Negative control was not performed normally.
Remedy: 1. From [#TEST AGEING] -> [AIR PUMP] -> [: Negative Pressure], check whether it is around — 5.0kPa at SPEED [188] and VALVE [_ _ _ _ _ _ _ _]. 2. Switch the valve one by one, with the pump speed [188] in [#TEST AGEING] -> [AIR PUMP] -> [:Negative Pressure], and check if there is a leak in the route where the pressure value has varied. 3. Check leakage of the chamber. 4. Replace the air filter.

Code: 61d
Display: ERROR 61d NEGATIVE P.NotEnough
Description: The negative pressure in the proper range cannot be maintained (at plus side).
Remedy: 1. From [#TEST AGEING] -> [AIR PUMP] -> [: Negative Pressure], check whether it is around — 5.4kPa at SPEED [188] and VALVE [_ _ _ _ _ _ _ _]. 2. Switch the valve one by one, with the pump speed [188] in [#TEST AGEING] -> [AIR PUMP] -> [:Negative Pressure], and check if there is a leak in the route where the pressure value has varied. 3. Check leakage of the chamber.

Code: 61e
Display: ERROR 61e NEGATIVE P.OVER
Description: The negative pressure in the proper range cannot be maintained (at minus side).
Remedy: 1. From [#TEST AGEING] -> [AIR PUMP] -> [: Negative Pressure], check whether it is around — 5.0kPa at SPEED [188] and VALVE [_ _ _ _ _ _ _ _]. 2. Switch the valve one by one, with the pump speed [188] in [#TEST AGEING] -> [AIR PUMP] -> [:Negative Pressure], and check if there is a leak in the route where the pressure value has varied.

Code: 61f
Display: ERROR 61f POSITIVE P.CONTROL
Description: Positive pressure control could not be performed normally.
Remedy: 1. From [#TEST AGEING] -> [AIR PUMP] -> [: Positive Pressure], check whether it is around — 5.0kPa at SPEED [188] and VALVE [_ _ _ _ _ _ _ _]. 2. Switch the valve one by one, with the pump speed [188] in [#TEST AGEING] -> [AIR PUMP] -> [:Negative Pressure], and check if there is a leak in the route where the pressure value has varied.

Code: 620
Display: ERROR 620 POSITIVE P.NotEnough
Description: The positive pressure in the proper range cannot be maintained (at minus side).
Remedy: 1. From [#TEST AGEING] -> [AIR PUMP] -> [: Positive Pressure], check whether it is around — 5.0kPa at SPEED [188] and VALVE [_ _ _ _ _ _ _ _]. 2. Switch the valve one by one, with the pump speed [188] in [#TEST AGEING] -> [AIR PUMP] -> [:Negative Pressure], and check if there is a leak in the route where the pressure value has varied.

	Error Code
	Service Mode, Troubleshooting
	Parts Catalog
	Compatibility
	Downloads Files
	Home

Источник

Catalog
Sign In
Contacts
Forum
Eng

Error Codes
Mimaki
JFX200-2513
All codes

Error Codes List page 16

Code: 61b
Display: ERROR 61b SUPPLY INK:12345678
Description: Ink filling into the sub-tank has failed.
Remedy: 1.With [#TEST SENSOR], check the detection status of the target liquid level detection sensor. (Also, visually check the float position in the sub-tank.) 2. From [#TEST AGEING] -> [PUMP MOTOR], discharge ink in the sub-tank to the bottom. From [#TEST AGEING] -> [INK SUPPLY], check that sending ink is performed. *If sending ink cannot be performed: The supply pump, the bottle valve and the UISS valve shall be replaced.

Code: 61c
Display: ERROR 61c NEGATIVE P.CONTROL
Description: Negative control was not performed normally.
Remedy: 1. From [#TEST AGEING] -> [AIR PUMP] -> [: Negative Pressure], check whether it is around — 5.0kPa at SPEED [188] and VALVE [_ _ _ _ _ _ _ _]. 2. Switch the valve one by one, with the pump speed [188] in [#TEST AGEING] -> [AIR PUMP] -> [:Negative Pressure], and check if there is a leak in the route where the pressure value has varied. 3. Check leakage of the chamber. 4. Replace the air filter.

Code: 61d
Display: ERROR 61d NEGATIVE P.NotEnough
Description: The negative pressure in the proper range cannot be maintained (at plus side).
Remedy: 1. From [#TEST AGEING] -> [AIR PUMP] -> [: Negative Pressure], check whether it is around — 5.4kPa at SPEED [188] and VALVE [_ _ _ _ _ _ _ _]. 2. Switch the valve one by one, with the pump speed [188] in [#TEST AGEING] -> [AIR PUMP] -> [:Negative Pressure], and check if there is a leak in the route where the pressure value has varied. 3. Check leakage of the chamber.

Code: 61e
Display: ERROR 61e NEGATIVE P.OVER
Description: The negative pressure in the proper range cannot be maintained (at minus side).
Remedy: 1. From [#TEST AGEING] -> [AIR PUMP] -> [: Negative Pressure], check whether it is around — 5.0kPa at SPEED [188] and VALVE [_ _ _ _ _ _ _ _]. 2. Switch the valve one by one, with the pump speed [188] in [#TEST AGEING] -> [AIR PUMP] -> [:Negative Pressure], and check if there is a leak in the route where the pressure value has varied.

Code: 61f
Display: ERROR 61f POSITIVE P.CONTROL
Description: Positive pressure control could not be performed normally.
Remedy: 1. From [#TEST AGEING] -> [AIR PUMP] -> [: Positive Pressure], check whether it is around — 5.0kPa at SPEED [188] and VALVE [_ _ _ _ _ _ _ _]. 2. Switch the valve one by one, with the pump speed [188] in [#TEST AGEING] -> [AIR PUMP] -> [:Negative Pressure], and check if there is a leak in the route where the pressure value has varied.

Code: 620
Display: ERROR 620 POSITIVE P.NotEnough
Description: The positive pressure in the proper range cannot be maintained (at minus side).
Remedy: 1. From [#TEST AGEING] -> [AIR PUMP] -> [: Positive Pressure], check whether it is around — 5.0kPa at SPEED [188] and VALVE [_ _ _ _ _ _ _ _]. 2. Switch the valve one by one, with the pump speed [188] in [#TEST AGEING] -> [AIR PUMP] -> [:Negative Pressure], and check if there is a leak in the route where the pressure value has varied.

	Error Code
	Service Mode, Troubleshooting
	Parts Catalog
	Compatibility
	Home

sprint33: Постоянный участник; Сообщения: 160; Зарегистрирован: 15 окт 2013 22:24; Последний визит: 27 янв 2023 22:55; Изменить репутацию:
Репутация:
Голосов: 1; Откуда: Владимир

Ошибка Mimaki JV33-160 BS

Подскажите что за ошибка?

Как устранить?

Вложения

: 1644351933.jpg (25.48 КБ) 2830 просмотров

Sokell: Старожил; Сообщения: 6703; Зарегистрирован: 20 июл 2010 13:33; Последний визит: 26 янв 2023 11:48; Изменить репутацию:
Репутация:
Голосов: 165; Откуда: Рязань

Сообщение Sokell » 17 май 2015 17:55

Выбрать нужный Вам тип чернил если Вы работаете на оригинале… Или тот тип чернил который у Вас «зашит» в чипах — если принтер расчипован…

Спаси меня господь от тех кому я верю,
от тех кому не – верю уберегусь я сам

sprint33: Постоянный участник; Сообщения: 160; Зарегистрирован: 15 окт 2013 22:24; Последний визит: 27 янв 2023 22:55; Изменить репутацию:
Репутация:
Голосов: 1; Откуда: Владимир

Сообщение sprint33 » 19 май 2015 08:30

ок.

Спасибо.

Вернёмся к этой теме через неделю, когда прибудет оборудование.

plotterhelp: Старожил; Сообщения: 2227; Зарегистрирован: 13 июн 2013 06:02; Последний визит: 26 янв 2020 14:26; Изменить репутацию:
Репутация:
Голосов: 66; Откуда: Москва

Сообщение plotterhelp » 19 май 2015 10:07

Аппарат новый? При запуске такое сообщение возникает. Или после дисчарджа. Когда приедет аппарат? Владимир — интересный регион :wink:

Александр Яковлевич: Активный участник; Сообщения: 467; Зарегистрирован: 20 мар 2009 10:46; Последний визит: 04 авг 2022 16:14; Изменить репутацию:
Репутация:
Голосов: 17; Откуда: Москва

Сообщение Александр Яковлевич » 20 май 2015 11:40

sprint33

Принтер либо промыт и просит выбрать заново тип чернил, либо на нем слетели (были сброшены) параметры. В первом случае — просто заправить, во втором — все заново настроить и откалибровать.

Тщательней надо, братцы, тщательней…, но без фанатизма!

sprint33: Постоянный участник; Сообщения: 160; Зарегистрирован: 15 окт 2013 22:24; Последний визит: 27 янв 2023 22:55; Изменить репутацию:
Репутация:
Голосов: 1; Откуда: Владимир

Сообщение sprint33 » 27 июн 2015 16:52

Александр Яковлевич писал(а): (→)sprint33
Принтер либо промыт и просит выбрать заново тип чернил, либо на нем слетели (были сброшены) параметры. В первом случае — просто заправить, во втором — все заново настроить и откалибровать.

Вот теперь всем привет…. :-)

Принтер приехал…..

Стоит СНЧП.

Очевидно он не видит или не распознаёт чипы.

Даёт только выбрать BS 1-2-3 ,выводит на экран Close an ink tupe.

И всё…. больше не реагирует ни на какие кнопки ….и вообще не даёт входить ни в какие менюшки.

Над картриджами горят все красные индикаторы.

Попробовали отключить СНЧП и воткнули обычные картриджы, РЕЗУЛЬТАТ ТОТ-ЖЕ.

Подскажите куда копать дальше?

Версия аппарата 3.80

Vovan72: Завсегдатай; Сообщения: 511; Зарегистрирован: 01 окт 2011 14:03; Последний визит: 24 янв 2023 21:49; Изменить репутацию:
Репутация:
Голосов: 20; Откуда: Санкт-Петербург

Сообщение Vovan72 » 27 июн 2015 20:35

Вероятно «Close an ink type». Машина BS, значит СНПЧ с чипами ВS3 как правило, но как кто расчиповывает.

AndreyT.: Старожил; Сообщения: 1516; Зарегистрирован: 17 авг 2012 11:38; Последний визит: 27 янв 2023 21:47; Изменить репутацию:
Репутация:
Голосов: 56; Откуда: Москва

Сообщение AndreyT. » 27 июн 2015 21:13

Вставляйте чипы ВС3 и все.

sprint33: Постоянный участник; Сообщения: 160; Зарегистрирован: 15 окт 2013 22:24; Последний визит: 27 янв 2023 22:55; Изменить репутацию:
Репутация:
Голосов: 1; Откуда: Владимир

Сообщение sprint33 » 27 июн 2015 23:20

Vovan72 писал(а): (→)Вероятно «Close an ink type». Машина BS, значит СНПЧ с чипами ВS3 как правило, но как кто расчиповывает.

Утверждают что расчиповывали в Смарт-т

Добавлено спустя 1 минуту 31 секунду:

AndreyT. писал(а): (→)Вставляйте чипы ВС3 и все.

Чипы то стоят и работали.
Потом появилась такая беда.

Добавлено спустя 15 минут 16 секунд:

plotterhelp писал(а): (→)Аппарат новый? При запуске такое сообщение возникает. Или после дисчарджа. Когда приедет аппарат? Владимир — интересный регион

Эта надпись появляется сразу после включения.

Даёт выбрать BS 1-2-3

И на этом всё. Больше ничего невозможно сделать.

Все 8 индикаторов горят красным.

Vovan72: Завсегдатай; Сообщения: 511; Зарегистрирован: 01 окт 2011 14:03; Последний визит: 24 янв 2023 21:49; Изменить репутацию:
Репутация:
Голосов: 20; Откуда: Санкт-Петербург

Сообщение Vovan72 » 28 июн 2015 09:54

Choose ink type — очевидно

стрелки вверх/вниз работают?

Выбираем BS3 — Enter

Выбираем цветовую схему.

А Вот тут нужны 8 картриджей промывки — вставляем.

Вставляем чернильницы — 8 шт (можно 4)

Лампочки зелененьким загораются.

Плоттер готов.

sprint33: Постоянный участник; Сообщения: 160; Зарегистрирован: 15 окт 2013 22:24; Последний визит: 27 янв 2023 22:55; Изменить репутацию:
Репутация:
Голосов: 1; Откуда: Владимир

Сообщение sprint33 » 28 июн 2015 12:05

Vovan72 писал(а): (→)Choose ink type — очевидно
стрелки вверх/вниз работают?
Выбираем BS3 — Enter
Выбираем цветовую схему.
А Вот тут нужны 8 картриджей промывки — вставляем.
Вставляем чернильницы — 8 шт (можно 4)
Лампочки зелененьким загораются.
Плоттер готов.

Всё так, но…

Картриджи стоят, принтер их видит.

Цветовая схема выводиться только одна (MMCCYYKK), и после ввода, светодиоды по-кругу помаргивают и остаются красными….. больше никакие кнопки не работают ….кроме ЕND , которая возвращает Close an ink type и даёт снова выбрать BS 1-2-3.

Больше ничего не дает делать.

Vovan72: Завсегдатай; Сообщения: 511; Зарегистрирован: 01 окт 2011 14:03; Последний визит: 24 янв 2023 21:49; Изменить репутацию:
Репутация:
Голосов: 20; Откуда: Санкт-Петербург

Сообщение Vovan72 » 28 июн 2015 13:24

чипы просроченные надо новые покупать если машина в локале а индикаторы мигают красным.

sprint33: Постоянный участник; Сообщения: 160; Зарегистрирован: 15 окт 2013 22:24; Последний визит: 27 янв 2023 22:55; Изменить репутацию:
Репутация:
Голосов: 1; Откуда: Владимир

Сообщение sprint33 » 28 июн 2015 13:44

Vovan72 писал(а): (→)чипы просроченные надо новые покупать если машина в локале а индикаторы мигают красным.

Что значит в локале?

Утверждают что расчиповывали в Смарт-т.

У них что, то- же срок использования есть?

Горят постоянно , не моргают.

Vovan72: Завсегдатай; Сообщения: 511; Зарегистрирован: 01 окт 2011 14:03; Последний визит: 24 янв 2023 21:49; Изменить репутацию:
Репутация:
Голосов: 20; Откуда: Санкт-Петербург

Сообщение Vovan72 » 28 июн 2015 14:04

вечный двигатель еще не изобрели, если горят, то выбран не тот чип чернил, бу у другого клиента покупалась?

sprint33: Постоянный участник; Сообщения: 160; Зарегистрирован: 15 окт 2013 22:24; Последний визит: 27 янв 2023 22:55; Изменить репутацию:
Репутация:
Голосов: 1; Откуда: Владимир

Сообщение sprint33 » 28 июн 2015 14:43

Vovan72 писал(а): (→)вечный двигатель еще не изобрели, если горят, то выбран не тот чип чернил, бу у другого клиента покупалась?

Да, взяли бу в таком состоянии.

До локала не доходит.

При включении после версии сразу выводит : «Choose an ink type»

Даёт выбрать BS 1-2-3.

Без разницы что ввести предлагает цветовую схему MMCCYYKK.

Распознаёт что картриджы стоят.

После ввода всё….. больше ничего нельзя сделать….кроме ЕND.

Ни в какие другие меню вообще не входит.

Индикаторы горят непрерывно красным.

Вот такая беда…..

Последний раз редактировалось sprint33 28 июн 2015 14:56, всего редактировалось 7 раз.

Вернуться в «Принтеры MIMAKI»

Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и 1 гость

Take out the 1 liter ink bottle, and slowly shake it twenty times and more.

• To prevent ink from leaking when you shake it, wear gloves and cover the ink bottle cap with a paper

towel etc. Being in that status, slowly shake it twenty times and more by flowing ink.

Remove the cap of the ink bottle set in the external

• First, cover the cap with a waste cloth etc. to prevent your

hands from getting dirty and then remove it.

While checking the ink remaining amount

indicator, add ink.

• Depending on the ink type, aluminum sheet adheres to the

bottle top surface. In such a case, remove it with a cutter.

• While checking the ink remaining amount indicator above

the ink bottle, add ink. For details, refer to P.1-25 «Rough

standard for adding ink».

1-14

• Before shaking it, check that the cap is firmly closed.

• If you shake it too strong, it may cause ink leakage. Therefore, perform this carefully.

• If the remaining amount of ink is less, ink in the bottle cannot be beaten enough. Tilt the

ink bottle until it becomes vertical.

Repeat this

Cover with paper towel firmly and shake ink slowly

Cap

TS330-1600 Блок подачи чернил 10 кг

Руководство по эксплуатации

Меры предосторожности

Символы
В этом документе символы используются для пояснения содержания предостережений по эксплуатации. Отображаемый символ зависит от содержания предупреждения. Поймите значение каждого символа и используйте эту машину безопасно и правильно.

Exampфайлы символов

Смысл
	ПРЕДУПРЕЖДЕНИЕ	Несоблюдение инструкций, отмеченных этим символом, может привести к смерти или серьезным травмам персонала. Внимательно прочтите его и используйте принтер надлежащим образом.
	ВНИМАНИЕ!	Несоблюдение указаний, обозначенных этим символом, может привести к травмам легкой или средней степени тяжести.
	ОБЩЕЕ ПРЕДУПРЕЖДЕНИЕ	Этот символ указывает на то, что показанные элементы необходимо отметить. Конкретные примечания нарисованы на рисунке.
	ОБЩЕЕ ОБЯЗАТЕЛЬНОЕ ДЕЙСТВИЯ	Этот символ указывает на то, что указанное действие должно быть выполнено. Конкретная инструкция показана на иллюстрации.
	ОБЩИЙ ЗАПРЕТ	Этот символ указывает на то, что показанное действие запрещено. Конкретное запрещенное действие показано на рисунке.
	ВАЖНАЯ ИНФОРМАЦИЯ	Важные примечания по использованию данного устройства отмечены этим символом. Обратитесь к операции.
	СОВЕТ	Полезная информация дается с этим символом. Обратитесь к операции.
	СПРАВКА	Этот символ указывает на справочную страницу для соответствующего контента. Щелкните текст, чтобы отобразить соответствующую страницу.

Предостережения по установке

Предупреждение об использовании

Предупреждение
Как обращаться с чернилами

При эксплуатации в плохо проветриваемом помещении или закрытом помещении обязательно установите систему вентиляции.
Если вы по ошибке проглотили чернила или чистящий раствор для ухода, отдохните и немедленно обратитесь к врачу. Никогда не глотайте рвотные массы.
Если вам неприятно вдохнуть большое количество пара, немедленно переместитесь в место со свежим воздухом и отдохните в тепле. Кроме того, немедленно обратитесь к врачу.
Если чернила прилипли к коже и одежде, немедленно промойте их водой с мылом.
При попадании чернил в глаза немедленно промойте их большим количеством чистой проточной воды в течение более 15 минут, тщательно промойте даже заднюю часть век. Как можно скорее обратитесь к врачу.
Держите чернильницы и емкости для отработанных чернил в недоступном для детей месте.
Предотвратите утечку чернил и их попадание в систему естественного водоснабжения и бытовые сточные воды.
Утилизируйте отработанные чернила в соответствии с местным законодательством.
Попросите компанию по утилизации промышленных отходов утилизировать пустые емкости для чернил и отработанные чернила.
Обязательно прочтите Паспорт безопасности (SDS) перед работой с чернилами.

Запрет на разборку или модификацию
Запрет на использование в рекламеamp охрана окружающей среды

Меры предосторожности

Предупреждение
Используйте специальные чернила

Блок подачи чернил Mimaki TS330 1600 10 кг — значок 2

Используйте специальные чернила Поймите, что если он поврежден из-за использования неспециализированных чернил, ремонт будет бременем для клиента.
При использовании чернил, отличных от специальных чернил, защитное устройство не работает.
Специальные чернила нельзя использовать для других принтеров. Принтер сломается.
Не заправляйте резервуар чернилами, кроме указанных нами. Пожалуйста, поймите, что мы не можем взять на себя всю ответственность за проблемы, вызванные использованием повторно заправленных чернил.

чернильница

• Храните чернильницу на высоте 1 м и ниже. Если вы храните его на высоте 1 м и выше, в случае падения чернильницы крышка может оторваться, и чернила могут рассыпаться.
• Переместив чернильницу из холодного места в теплое, оставьте ее на 3 часа и более при комнатной температуре.
• Откройте чернильницу непосредственно перед установкой. Если чернильный контейнер оставить на долгое время после его открытия, он может не печатать нормально.
• Израсходуйте емкость для чернил в течение 3 месяцев после ее открытия. После длительного периода открытия качество чернил ухудшается.
• Храните чернильницу в темном прохладном месте.
• Используйте специальный чернильный контейнер для этого аппарата. Этот аппарат распознает специальный резервуар для чернил и работает. В случае выхода из строя из-за переделки чернильного контейнера и т. д., даже в течение гарантийного срока, гарантия не распространяется.

Блок подачи чернил Mimaki TS330 1600 10 кг — значок 3

• Не прикасайтесь к контактной части печатной платы микросхемы с чернилами руками и не загрязняйте ее. Это может привести к повреждению печатных плат.
• Не стучите сильно по чернильнице и не трясите ее сильно. Чернила могут вытекать из резервуара.

Гибка трубы

• Будьте осторожны, чтобы не погнуть выступающую трубку в следующей ситуации.
При перегибе трубки требуется замена. Обратитесь к дилеру или в наш сервисный центр.
1. При перемещении к задней части машины для настройки носителя и т. д.
2. Замените чернильницу

Предупреждающие надписи

На машину наклеены предупреждающие этикетки. Обязательно полностью уясните предупреждение, данное на этикетках.
Если предупредительная этикетка неразборчива из-за пятен или оторвалась, приобретите новую у дистрибьютора или в нашем офисе продаж.

Нет.	№ заказа.	этикетка	Описание
1	M903330		Обязательно наденьте прилагаемые защитные очки и перчатки.

Название каждой части

Замените 10-килограммовый чернильный контейнер (если подсоединена трубка подачи)
Когда на вспомогательном дисплее отображается [ЧЕРНИЛА ЗАКОНЧИЛИСЬ] или [ЧЕРНИЛА ЗАКОНЧИЛИСЬ], выполните следующие действия.

Когда отображается [ЧЕРНИЛА КОНЕЦ]

Нажмите клавишу [ENTER], чтобы отменить отображение сообщения.
• Отобразится сообщение с предложением заменить чернила.
Снимите подающую трубку с чернильницы.
• Зацепите снятую подводящую трубу за ручку блока подачи.
Извлеките использованный контейнер для чернил.
• Если вы хотите использовать чернила, оставшиеся в контейнере для чернил, обратитесь к разделу «Пополнение оставшихся чернил» на стр. 10, а затем перейдите к следующему процессу.
Установите чернильницу на 10 кг на чернильный блок.
• Никогда не перемещайте контейнер после установки чернильницы. Это может привести к утечке чернил.
Снимите крышку чернильницы.
Удалите использованный чип Ink IC.
• Замените микросхему чернил после установки новой емкости для чернил на 10 кг.
Прикрепите микросхему чернил.
• После того, как ИС для чернил вставлена, блок подачи чернил подается автоматически.
• Автоматическая подача занимает не более 3 минут. Другие операции подачи и печать не могут выполняться, пока выполняется автоматическая подача.

Микросхема ИС для чернил имеет информацию о цвете чернил, оставшемся количестве чернил, сроке годности и т.п.
Чтобы установить чернильницу, вставьте микросхему чернил, упакованную вместе с чернильницей, в гнездо ИС для чернил.
Будьте осторожны, чтобы не установить микросхему чернил, которая не является парой чернильницы. Это может привести к ухудшению качества изображения или аналогичным проблемам.
Символ, указывающий информацию о цвете, прикреплен к микросхеме чернил.

Цвет чернил	Знак индикации
Черный (K)	(один черный круг)
Синий (БЛ)	(один синий круг/красный круг)
Пурпурный (М)	(один красный круг)
Желтый (Y)	(один желтый кружок)
Голубой (Lbl)	(два синих круга/красный круг)
Светло-пурпурный (лм)	(два красных круга)
Светло-черный (Lk)	(два черных круга)
Флуоресцентный желтый (FY)	(два желтых круга)
Флуоресцентный розовый (FP)	(два оранжевых круга)

Расположение чернильного бака каждого набора чернил и расположение микросхемы чернил
• В зависимости от набора чернил, ИС с четными номерами маршрутных чернил могут не использоваться.
Будьте осторожны, чтобы не вставить его по ошибке.

Устранить КОНЕЦ ЧЕРНИЛ
Если [INK (NEAR) END] появляется после замены чернильницы и автоматической подачи, сделайте следующее.

Обратитесь к P.7 «Замена 10-килограммового контейнера для чернил (при присоединенной подающей трубке)» и установите чернильный контейнер и подающую трубку.
Чтобы решить проблему [ЧЕРНИЛА (ПРЯМО) ЗАКОНЧИЛИСЬ], убедитесь, что емкость для чернил и трубка подачи чернил установлены правильно.
Выберите [ПРОБНАЯ ПЕЧАТЬ / ОЧИСТКА] > [Решение окончания чернил] и нажмите клавишу [ВВОД].
Нажмите клавишу [ENTER] на экране запуска подачи чернил 10 кг, чтобы начать подачу.
• Эта функция может устранить только маршрут с использованием 10-килограммовой емкости для чернил.

Когда отображается [ЧЕРНИЛА ЗАКОНЧИЛИСЬ]
Во флаконе остается очень мало чернил. Хотя операция печати может продолжаться без замены емкости с чернилами, чернила могут закончиться во время печати. Мы рекомендуем вам заменить чернильницу на новую вскоре после того, как это будет показано.
Если вы нажмете клавишу в локальном режиме, вы можете проверить замену бака у местных гидов.

Остаток пополнения чернил

Откройте новые чернила и установите воронку в носик.
• Накройте резервуар и встряхните его перед добавлением.
• Если чернила вытекут во время пополнения, пол может стать грязным.
Добавьте оставшиеся чернила.
• Будьте осторожны, чтобы не пролить.
Если чернила добавлены не полностью, напечатайте их в новом резервуаре на некоторое время, а после того, как чернила закончатся, добавьте их снова.
• При необходимости выполните
«О коррекции уровня чернил» на стр. 11.

О коррекции уровня чернил

Если разница между уровнем чернил IC и фактическим уровнем чернил в 10-килограммовом контейнере для чернил велика, исправьте ее с помощью [Коррекция остатка чернил].

Выполните коррекцию уровня чернил

Выберите [МЕНЮ] > [ОБСЛУЖИВАНИЕ] > [Коррекция оставшихся чернил] и нажмите клавишу [ВВОД].
Выберите слот, для которого вы хотите скорректировать оставшуюся сумму, с помощью клавиши и нажмите клавишу [ENTER].
Измените оставшийся заряд клавишей и нажмите клавишу [ENTER].
• Уровень оставшихся чернил скорректирован.
• Используйте шкалу на передней части резервуара в качестве ориентира для корректировки значения коррекции.

Обслуживание

Техническое обслуживание 10-килограммовой емкости для чернил
Раз в три дня перемешивайте чернила в баке, чтобы предотвратить осаждение компонентов чернил.
Появится сообщение с предложением перемешать чернильницу.

Снимите подающую трубку с чернильницы.
Перемешайте чернила с помощью подающей трубки.
• Энергично перемешайте каждый бак около 5 раз в вертикальном направлении.
Установите подающую трубку в чернильницу.
Нажмите клавишу [FUNC2], чтобы отменить отображение сообщения.

Если возникает аномалия

Если в 10-килограммовом чернильном контейнере или 2-литровом чернильном пакете возникает неисправность, появится предупреждающее сообщение.
Все операции, связанные со сливом чернил, такие как печать и очистка, не могут быть выполнены.
При возникновении ошибки сделайте следующее.

Убедитесь, что микросхема ИС для чернил правильно установлена в гнездо ИС.
Немедленно замените чернильницу на новую.
Не оставляйте его на долгое время, пока отображается неисправность чернильницы. Функция предотвращения засорения форсунок не работает.
При засорении форсунки требуется ремонт сервисным инженером.

Отображение сведений о неисправности чернильницы
Детали проблемы с чернильницей можно проверить, выполнив следующую операцию.

Нажмите клавишу [ENTER] в локальном режиме.
Нажмите клавишу [ВВОД].
• При возникновении сбоев в работе нескольких чернильниц нажатие клавиши [ENTER] отобразит их по порядку.

• Здесь отображается предупреждающее сообщение о блоке чернил. Информацию о других предупреждающих ошибках см. в руководстве по эксплуатации принтера.
• Подробную информацию о том, как отображать сведения об ошибках-предупреждениях, см. в руководстве по эксплуатации принтера.

Монитор	Вызывать	меры
НЕТ ЧЕРНИЛ IC	Микросхема чернил не вставлена в слот.	• Вставьте микросхему чернил в гнездо, где отображается предупреждение. •Убедитесь, что микросхема с чернилами вставлена правильно. • Если предупреждение остается даже после того, как микросхема с чернилами вставлена в гнездо, перезапустите аппарат. • Если снова отображается, обратитесь к местному дистрибьютору, в наш офис продаж или в сервисный центр.
ЧЕРНИЛА ИС ОШИБКА	Микросхема Ink IC не может быть правильно прочитана.	• Повторно вставьте микросхему с чернилами, показывающую предупреждение. • Если предупреждение не устраняется, обратитесь к местному дистрибьютору, в наш офис продаж или в сервисный центр.
Расход чернил превышен	Поскольку микросхема с чернилами не была заменена вместе с заменой упаковки, количество использованных микросхем с чернилами превысило указанное количество.	• Замените чернильный пакет слота или 10-килограммовый чернильный контейнер, в котором появилось предупреждение, и его чернильную ИС.
Тип чернил	Тип чернил чернильной ИС отличается от чернил, которые были повторно заправлены.	• Проверьте тип чернил слота, в котором указано предупреждение.
Цвет чернил	Цвет чернил на ИС с чернилами отличается от цвета чернил, которые были повторно заправлены.	•Проверьте цвет чернил слота, в котором указано предупреждение.
Чернила почти закончились	Чернила в чернильном пакете или 10-килограммовом чернильном контейнере немного остались.	•Чернила скоро закончатся. Будь осторожен.
Конец чернил	Закончились чернила в чернильном пакете или емкости для чернил емкостью 10 кг.	• Замените чернильный пакет слота или 10-килограммовый чернильный контейнер, в котором появилось предупреждение, и его чернильную ИС.
До истечения дней	Срок действия ссылки истек (менее 2 месяцев до истечения срока действия).	• Замените чернильный пакет слота или 10-килограммовый чернильный контейнер, в котором появилось предупреждение, и его чернильную ИС.
Срок годности превышен.	Срок действия ссылки истек (с момента истечения срока действия прошло более 2 месяцев).	• Замените чернильный пакет (или чернильный контейнер на 10 кг) слота, в котором появляется предупреждение, и чернильную ИС.
Датчик дополнительного бака	Значение датчика вспомогательного резервуара не может быть определено нормально.	• Перезапустите машину. • Если снова отображается, обратитесь к местному дистрибьютору, в наш офис продаж или в сервисный центр.

Остаток бака H	Даже когда чернила израсходованы, количество чернил во вспомогательном резервуаре не уменьшается. ・Сбой всасывания чернил. ・Произошло сильное засорение форсунок.	• Перезапустите машину. • Если снова появится, обратитесь к местному дистрибьютору, в наш офис продаж или в сервисный центр.
Остаток бака л

предисловие
Поздравляем с приобретением чернильного блока на 10 кг.

Это руководство по эксплуатации

В этом руководстве объясняется, как работать с 10-килограммовым чернильным блоком.
Прочтите и полностью уясните это руководство по эксплуатации перед использованием этой машины. Также необходимо иметь под рукой данное руководство по эксплуатации.
Примите меры для передачи данного руководства по эксплуатации лицу, отвечающему за эксплуатацию 10-килограммового блока чернил.
Несмотря на то, что это руководство по эксплуатации было тщательно подготовлено для облегчения понимания, пожалуйста, не стесняйтесь обращаться к местному дистрибьютору, если у вас есть какие-либо вопросы.
Содержание данного руководства по эксплуатации может быть изменено без предварительного уведомления. Пожалуйста, обрати внимание.
Если это руководство стало неразборчивым из-за повреждения или уничтожено из-за пожара или по аналогичной причине, приобретите еще один экземпляр руководства по эксплуатации в нашем офисе продаж.

ВНИМАНИЕ!
НАСТОЯЩАЯ ОГРАНИЧЕННАЯ ГАРАНТИЯ MIMAKI БУДЕТ ЕДИНСТВЕННОЙ И ИСКЛЮЧИТЕЛЬНОЙ ГАРАНТИЕЙ И ЗАМЕНЯЕТ ВСЕ ДРУГИЕ ГАРАНТИИ, ЯВНЫЕ ИЛИ ПОДРАЗУМЕВАЕМЫЕ, ВКЛЮЧАЯ, ПОМИМО ПРОЧЕГО, ЛЮБЫЕ ПОДРАЗУМЕВАЕМЫЕ ГАРАНТИИ КОММЕРЧЕСКОЙ ПРИГОДНОСТИ ИЛИ ПРИГОДНОСТИ, ЭТО ЛЮБЫЕ ДРУГИЕ ОБЯЗАТЕЛЬСТВА ИЛИ ОТВЕТСТВЕННОСТЬ, ИЛИ ПРЕДОСТАВЛЕНИЕ ЛЮБОЙ ДРУГОЙ ГАРАНТИИ, ИЛИ ПРЕДОСТАВЛЕНИЕ ЛЮБОЙ ДРУГОЙ ГАРАНТИИ В СВЯЗИ С ЛЮБЫМ ПРОДУКТОМ БЕЗ ПРЕДВАРИТЕЛЬНОГО ПИСЬМЕННОГО СОГЛАСИЯ MIMAKI.
НИ ПРИ КАКИХ ОБСТОЯТЕЛЬСТВАХ КОМПАНИЯ MIMAKI НЕ НЕСЕТ ОТВЕТСТВЕННОСТИ ЗА ОСОБЫЕ, СЛУЧАЙНЫЕ ИЛИ КОСВЕННЫЕ УБЫТКИ ИЛИ ЗА ПОТЕРЮ ПРИБЫЛИ ПРОДАВЦА ИЛИ ПОКУПАТЕЛЕЙ ЛЮБОГО ПРОДУКТА.

Воспроизведение данного руководства строго запрещено.
© Mimaki Engineering Co., Ltd.
Все права защищены. Авторские права
МИМАКИ ИНЖИНИРИНГ КО., ЛТД.
https://mimaki.com/
https://japan.mimaki.com/

Документы / Ресурсы

Fixing Mimaki UJF6042 Error Codes list

– Compatible Printer model: Mimaki UJF6042
– Mimaki UJF6042 Error Code description:

Code: 000
Display: SYSTEM HALT (*) 000 : IOC1/ADC
Description: System error (STC3 A/D start error)
Troubleshooting Guides: 1. Confirm the neighboring temperature of the Station III PCB. In addition, confirm whether and it is an error by the heat reckless driving of FPGA. 2. Confirm whether there is not a device generating powerful electromagnetic waves to circumference. 3. Replace the Slider PCB with a new one. 4. Replace the Main PCB with a new one. 5. Replace the Power Supply PCB with a new one.

Code: 000
Display: SYSTEM HALT (*) 000 : IOC2/ADC
Description: System error (SPC A/D start error)
Troubleshooting Guides: 1. Confirm the neighboring temperature of the SL-Relay PCB. In addition, confirm whether and it is an error by the heat reckless driving of FPGA. 2. Confirm whether there is not a device generating powerful electromagnetic waves to circumference. 3. Replace the Slider PCB with a new one. 4. Replace the Main PCB with a new one. 5. Replace the Power Supply PCB with a new one.

Code: 000
Display: SYSTEM HALT (*) 000 : HDC/ADC
Description: System error (HDC A/D start error)
Troubleshooting Guides: 1. Confirm the neighboring temperature of the Slider PCB. In addition, confirm whether and it is an error by the heat reckless driving of FPGA. 2. Confirm whether there is not a device generating powerful electromagnetic waves to circumference. 3. Replace the Slider PCB with a new one. 4. Replace the Main PCB with a new one. 5. Replace the Power Supply PCB with a new one.

Code: 000
Display: SYSTEM HALT (*) 000 : UNNOWN ERR
Description: Unnown error
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Replace the Main PCB with a new one.

Code: 04
Display: ERROR 04 PARAM ROM
Description: Access Error of the PARAMETER ROM 1.The state that cannot access “ROM” on the SL-Relay PCB. 2.The state that cannot access “EEPROM” on the HEAD2.
Troubleshooting Guides: (If “PCB SLRY” is displayed for a few seconds while a version is displayed at startup before displaying errors) 1. Disconnect and connect the FFC located between the SL-Relay PCB and the Main PCB. 2. Disconnect and connect the FFC located between the Slider PCB and the SL-Relay PCB. 3. Replace the FFC located between the SL-Relay PCB and the Main PCB. 4. Replace the FFC located between the Slider PCB and the SL-Relay PCB. 5. Replace the SL-Relay PCB. 6. Replace the Slider PCB. 7. Replace the Main PCB. ( If ‘Area:_H__’ is displayed on the second line without ‘PCB SLRY’ displayed at startup by pressing [FUNC] key while an error is displayed.) 1. Disconnect and connect the FFC of the HEAD2. 2. Replace the Slider PCB. 3. Replace the HEAD2.

Code: 104
Display: SYSTEM HALT (*) 104 : +35V RECVR
Description: 35 V Power recovery error
Troubleshooting Guides: 1.Replace the Power Supply PCB with a new one. 2. Replace the Main PCB with a new one.

Code: 108
Display: ERROR 108 HD CONNECT[12345678]
Description: Head connection error (Head connection can not be confirmed)
Troubleshooting Guides: 1. Check the setting of loading number of the head in the parameter. (System parameter No.41 HEAD NO=3) 2. Disconnect and connect the FFC located between the Slider PCB and the SL-Relay PCB. 3. Check connection between the Slider PCB from the Print Head 4. Replace the Slider PCB with a new one. 5. Replace the Print Head with a new one.

Code: 108
Display: ERROR 108 HD THERMIS[12345678]
Description: Head thermistor (Head temperature can not be measured)
Troubleshooting Guides: 1. Check the setting of loading number of the head in the parameter. (System parameter No.41 HEAD NO=3) 2. Disconnect and connect the FFC located between the Slider PCB and the SL-Relay PCB. 3. Check connection between the Slider PCB from the Print Head 4. Replace the Slider PCB with a new one. 5. Replace the Print Head with a new one.

Code: 10a
Display: SYSTEM HALT (*) 10a : HDC INIT
Description: Initialization error of the Slider PCB (FPGA)
Troubleshooting Guides: 1. Check the connections between the SL-Relay PCB and the Slider PCB, and then disconnect and connect the FFCs or the like. 2. Check the connections between the SL-Relay PCB and the Main PCB, and then disconnect and connect the FFCs or the like. 3. Replace the FFCs and the cabeles of the above routes. 4. Replace the Slider PCB with a new one. 5. Replace the SL-Relay PCB with a new one. 6. Replace the Main PCB with a new one.

Code: 10b
Display: SYSTEM HALT (*) 10b : PCB SLRY-F3
Description: Initialization error of the SL-Relay PCB (FPGA)
Troubleshooting Guides: 1. Check the connections between the SL-Relay PCB and the Main PCB, and then disconnect and connect the FFCs or the like. 2. Replace the FFCs of the above routes. 3. Replace the SL-Relay PCB with a new one. 4. Replace the Main PCB with a new one.

Code: 10e
Display: SYSTEM HALT (*) 10e :FROM CLEAR
Description: F-ROM CLEAR error (F-ROM clear unable) F-ROM is not clearable on Parameter writing, FW down loading and Log clearing. (fls_secclr)
Troubleshooting Guides: 1. Execute the memory check (F-ROM) of [#TEST]. 2. Upload the parameter and initialize all parameters with [#PARAMETER]. 3. Replace the Main PCB with a new one.

Code: 10f
Display: SYSTEM HALT (*) 10f : FROM WRITE
Description: FROM WRITE error (F-ROM writing unable) F-ROM is not clearable on Parameter writing, FW down loading and Log clearing. (fls_secclr)
Troubleshooting Guides: 1. Execute the memory check (F-ROM) of [#TEST]. 2. Upload the parameter and initialize all parameters with [#PARAMETER]. 3. Replace the Main PCB with a new one.

– Mimaki UJF6042 Error codes and solution steps to solve problems:

Code: 110
Display: SYSTEM HALT (*) 110 : PCB KEY
Description: No Keyboard PCB
Troubleshooting Guides: 1. Check the connections between the Keyboard PCB and the Main PCB and then disconnect and connect the FFCs. 2. Replace the FFCs of the above routes. 3. Replace the Keyboard PCB with a new one. 4. Replace the Main PCB with a new one. (Refer to 3.3.1

Code: 114
Display: SYSTEM HALT (*) 114 : PCB PUMP
Description: No Pump III PCB
Troubleshooting Guides: 1.Check the connections between the Pump PCB and the Main PCB, and then disconnect and connect the FFCs . 2. Replace the FFCs of the above routes. 3. Replace the Pump III PCB with a new one. 4. Replace the Main PCB with a new one. 5. Replace the SL-Relay PCB with a new one.

Code: 115
Display: SYSTEM HALT (*) 115 : PCB MAIN-F1
Description: Main PCB fuse (F1) disconnected.
Troubleshooting Guides: Replace the Main PCB with a new one. Before Main PCB replace, do the following checks. 1. Check the connections between the SL-Relay PCB and the Main PCB, and then disconnect and connect the FFCs or the like. 2. Check short between 1 pin and 12 pin, and between 3 pin and 12 pin of CN6 of the SL-Relay PCB. (If shorted out, replace also the SL-Relay PCB.) 3. Check the connections between the SL-Relay PCB and the Slider PCB and then disconnect and connect the FFCs or the like. 4. Check short between 1 pin and 16 pin, and between 3 pin and 16 pin of CN1 of the Slider PCB. (If shorted out, replace also the Slider PCB.)

Code: 116
Display: SYSTEM HALT (*) 116 : PCB MAIN-F2
Description: Main PCB fuse (F2) disconnected.
Troubleshooting Guides: Replace the Main PCB with a new one. Before Main PCB replace, do the following checks. 1. Check the connections between the SL-Relay PCB and the Main PCB, and then disconnect and connect the FFCs or the like. 2. Check short between 1 pin and 12 pin, and between 3 pin and 12 pin of CN6 of the SL-Relay PCB. (If shorted out, replace also the SL-Relay PCB.) 3. Check the connections between the SL-Relay PCB and the Slider PCB and then disconnect and connect the FFCs or the like. 4. Check short between 1 pin and 16 pin, and between 3 pin and 16 pin of CN1 of the Slider PCB. (If shorted out, replace also the Slider PCB.)

Code: 117
Display: SYSTEM HALT (*) 117 : PCB MAIN-F3
Description: Main PCB fuse (F3) disconnected.
Troubleshooting Guides: Replace the Main PCB with a new one. Before Main PCB replace, do the following checks. 1. Check the connections between the SL-Relay PCB and the Main PCB, and then disconnect and connect the FFCs or the like. 2. Check short between 1 pin and 12 pin, and between 3 pin and 12 pin of CN6 of the SL-Relay PCB. (If shorted out, replace also the SL-Relay PCB.) 3. Check the connections between the SL-Relay PCB and the Slider PCB and then disconnect and connect the FFCs or the like. 4. Check short between 1 pin and 16 pin, and between 3 pin and 16 pin of CN1 of the Slider PCB. (If shorted out, replace also the Slider PCB.)

Code: 11b
Display: SYSTEM HALT (*) 11b : SLDR FPC L
Description: Connection check error of FPC cable between SL-Relay PCB and Slider PCB
Troubleshooting Guides: 1. Check whether FPC cable connection connector of the Slider PCB (CN2, 4, 6) and the SL-Relay PCB (CN3, 7, is proper. 2. Disconnect and connect the FFC and Twist pair Cable located between the Slider PCB and the SL-Relay PCB. 3. Disconnect and connect the FFC and Twist pair Cable located between the Main PCB and the SL-Relay PCB. 4. Replace the FFC(or Twist pair Cable) located between the Slider PCB and the SL-Relay PCB. 5. Replace the FFC(or Twist pair Cable) located between the Main PCB and the SL-Relay PCB. 6. Replace the Slider PCB with a new one. 7. Replace the SL-Relay PCB with a new one. 8. Replace the Main PCB with a new one.

Code: 11d
Display: SYSTEM HALT (*) 11d : PCB SLRY-F1
Description: SL-Relay PCB fuse (F1) disconnected.
Troubleshooting Guides: Replace the SL-Relay PCB with a new one. Before SL-Relay PCB replace, do the following checks. 1. Check the connections between the Slider PCB and the SL-Relay PCB, and then disconnect and connect the FFCs. 2. Check short between 1 pin and 4 pin of CN1, and between 1 pin and 9 pin of CN11 of the Slider PCB. (If shorted out, replace also the Slider PCB.)

Code: 11e
Display: SYSTEM HALT (*) 11e : PCB SLRY-F4
Description: No SL-Relay PCB.
Troubleshooting Guides: 1. Check the connections between the SL-Relay PCB and the Main PCB, and then disconnect and connect the FFCs or the like. 2. Replace the FFCs of the above routes. 3. Replace the SL-Relay PCB with a new one. 4. Replace the Main PCB with a new one.

Code: 11f
Display: SYSTEM HALT (*) 11f : PCB SLIDER
Description: No Slider PCB.
Troubleshooting Guides: 1. Check the connections between the SL-Relay PCB and the Slider PCB, and then disconnect and connect the FFCs or the like. 2. Check the connections between the SL-Relay PCB and the Main PCB, and then disconnect and connect the FFCs or the like. 3. Replace the FFCs and the cabeles of the above routes. 4. Replace the Slider PCB with a new one. 5. Replace the SL-Relay PCB with a new one. 6. Replace the Main PCB with a new one.

Code: 120
Display: SYSTEM HALT (*) 120 : LCD THERM.
Description: LCD thermistor IC RW error
Troubleshooting Guides: 1.Check the connections between the Keyboard PCB and the Main PCB, and then disconnect and connect the FFCs. 2. Replace the FFCs and the cabeles of the above routes. 3. Replace the Keyboard PCB with a new one. 4. Replace the Main PCB with a new one. 5. Replace the Power Supply PCB with a new one.

Code: 122
Display: SYSTEM HALT (*) 122 : PRAM NONE
Description: No PRAM
Troubleshooting Guides: 1. Update F/W. 2. Replace the Main PCB with a new one.

Code: 122
Display: ERROR 122 CHECK:SDRAM
Description: PRAM size is not sufficient at FW upgrading (fw_updmsg).
Troubleshooting Guides: 1. Update F/W. 2. Replace the Main PCB with a new one.

Code: 123
Display: SYSTEM HALT (*) 123 : PRAM DATA
Description: PRAM data error
Troubleshooting Guides: 1. Update F/W. 2. Replace the Main PCB with a new one.

Code: 124
Display: SYSTEM HALT (*) 124 : PRAM ADDR
Description: PRAM address error
Troubleshooting Guides: 1. Update F/W. 2. Replace the Main PCB with a new one.

Code: 125
Display: SYSTEM HALT (*) 125 : EEPROM READ
Description: EEPROM read trouble
Troubleshooting Guides: 1.Update F/W. 2. Upload the parameter and initialize parameter with #PARAMETER. 3. Check the connection state between Main PCB ~ SLRelay PCB. 4. Replace the Main PCB with a new one. 5. Replace the SL-Relay PCB with a new one.

Code: 126
Display: SYSTEM HALT (*) 126 : EEPROM WR
Description: EEPROM write trouble
Troubleshooting Guides: 1.Update F/W. 2. Upload the parameter and initialize parameter with #PARAMETER. 3. Check the connection state between Main PCB ~ SLRelay PCB. 4. Replace the Main PCB with a new one. 5. Replace the SL-Relay PCB with a new one.

Code: 127
Display: SYSTEM HALT (*) 127 : POWER OFF
Description: Power OFF detection error (Not to OFF) Power OFF process is conducted in the Power ON/OFF control without pushing down the sub-power SW.
Troubleshooting Guides: 1. Check the connection state between sub-power SW and Keyboard PCB. 2. Check the connections between the Keyboard PCB and the Main PCB, and then disconnect and connect the FFCs. 3. Check the connector connection of Power Supply PCB. 4. Check if there is no error on the power path from the AC Inlet. 5. Replace the Power Supply PCB with a new one. ( ) 6. Replace the Keyboard PCB with a new one. 7. Replace the Main PCB with a new one. 8. Replace the Station III PCB with a new one. 9. Replace the SL-Relay PCB with a new one. 10. Replace the Slider PCB with a new one.

Code: 128
Display: ERROR 128 HDC FIFO OVER
Description: HDC FIFO OVER error (Data transmission speed is too fast Control PCB trouble) HDC FIFO OVERRUN is detected at the scan slider process (ScanSlider)
Troubleshooting Guides: 1. Check the parameter. (Is the scan parameter the default value?) 2. Update F/W. 3. Check if there is no data error from RIP. 4. To make sure, repeat RIP. 5. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 6. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 7. Replace the FFC located between the Main PCB and the SL-Relay PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Slider PCB with a new one. 10. Replace the SL-Relay PCB with a new one. 11.Replace the Main PCB with a new one.

Code: 128
Display: ERROR 128 HDC FIFO UNDER
Description: HDC FIFO UNDER error (Data transmission speed is too slow Control PCB trouble) HDC FIFO UNDERRUN is detected at the scan slider process (ScanSlider)
Troubleshooting Guides: 1. Check the parameter. (Is the scan parameter the default value?) 2. Update F/W. 3. Check if there is no data error from RIP. 4. To make sure, repeat RIP. 5. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 6. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 7. Replace the FFC located between the Main PCB and the SL-Relay PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Slider PCB with a new one. 10. Replace the SL-Relay PCB with a new one. 11.Replace the Main PCB with a new one.

Code: 129
Display: ERROR 129 BATTERY EXCHANGE
Description: Battery dead (RTC battery dead is detected.) Proper information of Printer or Time (Dedicated IC) unusable on Printer initializing process (opinit).
Troubleshooting Guides: 1. Replace a battery equipped on the Main PCB with new one. (CR2032) * The new battery should be the same product or the equivalent. * Discard the old battery according to the instruction from the maker.

Code: 12d
Display: SYSTEM HALT (*) 12d : PCB MAIN-F4
Description: Main PCB fuse (F4) disconnected.
Troubleshooting Guides: Replace the Main PCB with a new one. Before Main PCB replace, do the following checks. 1. Check the connections between the SL-Relay PCB and the Main PCB, and then disconnect and connect the FFCs or the like. 2. Check short between 1 pin and 12 pin, and between 3 pin and 12 pin of CN6 of the SL-Relay PCB. (If shorted out, replace also the SL-Relay PCB.) 3. Check the connections between the SL-Relay PCB and the Slider PCB and then disconnect and connect the FFCs or the like. 4. Check short between 1 pin and 16 pin, and between 3 pin and 16 pin of CN1 of the Slider PCB. (If shorted out, replace also the Slider PCB.)

Code: 12e
Display: ERROR 12e Head Faild[xxxx] (The details of [xxxx] are explained below this list.)
Description: Abnormality of the Print head. Abnormality of the Driver of the Print head.
Troubleshooting Guides: 1. Update F/W. 2. Initialize a parameter. 3. Disconnect and connect the FFC located between the Slider PCB and the SL-Relay PCB. 4. Replace the FFC located between the Slider PCB and the SL-Relay PCB. 5. Replace the Print Head with a new one. 6. Replace the Slider PCB with a new one. 7. Replace the SL-Relay PCB with a new one.

Code: 130
Display: ERROR 130 HD DATA SEQ
Description: Head data transferring sequence error
Troubleshooting Guides: 1. Disconnect and connect the FFC located between the Slider PCB and the SL-Relay PCB. 2. Disconnect and connect the FFC located between the SL-Relay PCB and the Main PCB. 3. Replace the FFC located between the Slider PCB and the SL-Relay PCB. 4. Replace the FFC located between the SL-Relay PCB and the Main PCB. 5. Replace the Slider PCB with a new one. 6. Replace the SL-Relay PCB with a new one. 7. Replace the Main PCB with a new one.

Code: 13c
Display: SYSTEM HALT (*) 13c : PCB SLRY-F2
Description: SL-Relay PCB fuse (F2) disconnected.
Troubleshooting Guides: Replace the SL-Relay PCB with a new one. Before SL-Relay PCB replace, do the following checks. 1. Check the connections between the Slider PCB and the SL-Relay PCB, and then disconnect and connect the FFCs. 2. Check short between 1 pin and 4 pin of CN1, and between 1 pin and 9 pin of CN11 of the Slider PCB. (If shorted out, replace also the Slider PCB.)

Code: 13d
Display: SYSTEM HALT (*) 13d : PCB SLRY-F3
Description: SL-Relay PCB fuse (F3) disconnected.
Troubleshooting Guides: Replace the SL-Relay PCB with a new one. Before SL-Relay PCB replace, do the following checks. 1. Check the connections between the Pump III PCB and the SL-Relay PCB, and then disconnect and connect the FFCs. 2. Check short between 1 pin and 4 pin of CN1, and between 1 pin and 9 pin of CN6 of the Pump III PCB. (If shorted out, replace also the Pump III PCB.)

Code: 13e
Display: SYSTEM HALT (*) 13e : PCB STATION-F1
Description: Station PCB fuse (F1) disconnected.
Troubleshooting Guides: 1. Replace the Station III PCB with a new one.

Code: 13f
Display: SYSTEM HALT (*) 13f : PCB STATION-F2
Description: Station PCB fuse (F2) disconnected.
Troubleshooting Guides: 1. Replace the Station III PCB with a new one.

Code: 140
Display: SYSTEM HALT (*) 140 : PCB STATION-F3
Description: Station PCB fuse (F3) disconnected.
Troubleshooting Guides: 1. Replace the Station III PCB with a new one.

Code: 146
Display: ERROR 146 E-LOG SEQ
Description: Sequential number abnormality of the event log
Troubleshooting Guides: 1. Initialize a Event log. 2. Replace the Main PCB with a new one.

Code: 147
Display: SYSTEM HALT (*) 147 : DS-IC BUSY
Description: DALLAS IC BUSY error
Troubleshooting Guides: 1. Check connection of the ID Contact PCB connection cable and damage of the cable. 2. Try to use a different cartridge. 3. Replace the ID Contact PCB Assy. with a new one. 4. Replace the SL-Relay PCB with a new one.

Code: 149
Display: SYSTEM HALT (*) 149 : PCB SLRY-F4
Description: SL-Relay PCB fuse (F4) disconnected.
Troubleshooting Guides: Replace the SL-Relay PCB with a new one. Before SL-Relay PCB replace, do the following checks. 1. Check the connections between the Pump III PCB and the SL-Relay PCB, and then disconnect and connect the FFCs. 2. Check short between 1 pin and 4 pin of CN1, and between 1 pin and 9 pin of CN6 of the Pump III PCB. (If shorted out, replace also the Pump III PCB.)

Code: 151
Display: ERROR 151 Main PCB V1R2
Description: Main board 1.2V power supply is abnormal.
Troubleshooting Guides: 1. Replace the Main PCB with a new one.

Code: 152
Display: ERROR 152 Main PCB V2R5
Description: Main board 2.5V power supply is abnormal.
Troubleshooting Guides: 1. Replace the Main PCB with a new one.

Code: 153
Display: ERROR 153 Main PCB V3R3
Description: Main board 3.3V power supply is abnormal.
Troubleshooting Guides: 1. The output voltage check of the Power supply PCB. 2. Replace the Power supply PCB with a new one. 3.Replace the Main PCB with a new one.

Code: 154
Display: ERROR 154 Main PCB V05
Description: Main board 5V power supply is abnormal.
Troubleshooting Guides: 1. The output voltage check of the Power supply PCB. 2. Replace the Power supply PCB with a new one. 3.Replace the Main PCB with a new one.

Code: 155
Display: ERROR 155 Main PCB V35-1
Description: Main board 35-1V power supply is abnormal.
Troubleshooting Guides: 1. The output voltage check of the Power supply PCB. 2. Replace the Power supply PCB with a new one. 3.Replace the Main PCB with a new one.

Code: 156
Display: ERROR 156 Main PCB V5B
Description: Main board 5VB power supply is abnormal.
Troubleshooting Guides: 1. The output voltage check of the Power supply PCB. 2. Replace the Power supply PCB with a new one. 3.Replace the Main PCB with a new one.

Code: 157
Display: ERROR 157 Main PCB VTT
Description: Main board VTT power supply is abnormal.
Troubleshooting Guides: 1. Replace the Main PCB with a new one.

Code: 158
Display: ERROR 158 Main PCB V352
Description: Main board 35-2V power supply is abnormal.
Troubleshooting Guides: 1. Replace the Main PCB with a new one.

Code: 159
Display: SYSTEM HALT (*) 159 : PCB SLDR-F1
Description: Slider PCB fuse (F1) disconnected
Troubleshooting Guides: 1. Replace the Slider PCB with a new one.

Code: 15a
Display: SYSTEM HALT (*) 15a : PCB STA3
Description: No Station III PCB
Troubleshooting Guides: 1.Check the connections between the Station III PCB and the Main PCB, and then disconnect and connect the FFCs. 2. Replace the FFCs of the above routes. 3. Replace the Station III PCB with a new one. 4. Replace the Main PCB with a new one.

Code: 15a
Display: SYSTEM HALT (*) 15a : MAIN FPC-1
Description: 30pinFPC1 of Main PCB connect error
Troubleshooting Guides: 1. Check the connections between the SL-Relay PCB and the Main PCB, and then disconnect and connect the FFCs. 2. Replace the FFCs of the above routes. 3. Replace the SL-Relay PCB with a new one. 4. Replace the Main PCB with a new one.

Code: 15f
Display: ERROR 15f HEAD DRIVE HOT
Description: COM driver becomes the high temperature.
Troubleshooting Guides: 1. Confirm movement of Slider Relay Cooling Fan. 2. Disconnect and connect the FFC located between the Slider PCB and the SL-Relay PCB. 3. Replace the SL-Relay PCB with a new one. 4. Replace the FFC located between the Slider PCB and the SL-Relay PCB 5. Replace the Print Head with a new one. 6. Replace the Slider PCB with a new one.

Code: 160
Display: SYSTEM HALT (*) 160 : PCB MAIN-F5
Description: Main PCB fuse (F5) disconnected.
Troubleshooting Guides: Replace the Main PCB with a new one. Before Main PCB replace, do the following checks. 1. Check the connections between the Station III PCB and the Main PCB, and then disconnect and connect the FFCs. 2. Check short between 1 pin and 4 pin of CN1, and between 1 pin and 9 pin of CN11 of the Station III PCB. (If shorted out, replace also the Station III PCB.)

Code: 161
Display: SYSTEM HALT (*) 161 : PCB MAIN-F6
Description: Main PCB fuse (F6) disconnected.
Troubleshooting Guides: Replace the Main PCB with a new one. Before Main PCB replace, do the following checks. 1. Check the connections between the Station III PCB and the Main PCB, and then disconnect and connect the FFCs. 2. Check short between 1 pin and 4 pin of CN1, and between 1 pin and 9 pin of CN11 of the Station III PCB. (If shorted out, replace also the Station III PCB.)

Code: 16e
Display: ERROR 16e Main PCB V3R3B
Description: Main board 3.3VÇa power supply is abnormal.
Troubleshooting Guides: 1. Replace the Main PCB with a new one.

Code: 170
Display: SYSTEM HALT (*) 170 : PCB UVLEDDRV
Description: No Driver PCB of LED UV UNIT?
Troubleshooting Guides: 1. Check the connections between the Slider PCB and the LED UV Unit, and then disconnect and connect the cables. 2. Replace the FFC and the cabele located between the Slider PCB and the SL-Relay PCB. 3. Replace the cabele located between the Slider PCB and the LED UV Unit. 4. Replace the SL-Relay PCB with a new one. 5. Replace the LED UV UNIT Assy with a new one.

Code: 171
Display: ERROR 171 NEW HEAD CONNECT
Description: New Print Head was recognized.
Troubleshooting Guides: It is normal that an error occurs only at the time of the first start after having connected a new head. It is abnormal that an error occurs at the time of start every time.. 1. Check connection between the Slider PCB from the Print Head 2. Replace the Slider PCB with a new one. 3. Replace the Print Head with a new one.

Code: 172
Display: ERROR 172 Main PCB Q6 Check
Description: The main PCB Q6 is disabled (short mode). (Displayed only at startup in the maintenance open mode or other than SUPPORT=0.)
Troubleshooting Guides: 1. Replace the Main PCB with a new one.

Code: 201
Display: ERROR 201 COMMAND
Description: Command error Other data than commands is received
Troubleshooting Guides: 1. Check if the output set of the PC matches the set of the machine side? 2. Change the profile. 3. Check if there is no parameter error? 4. Check if there is no trouble on the USB Cable? 5. Replace the USB Cable. 6. Replace the Main PCB with a new one.

Code: 202
Display: ERROR 202 PARAMETER
Description: Parameter error Parameter out of the numeral value range is received
Troubleshooting Guides: 1. Check if the output set of the PC matches the set of the machine side? 2. Change the profile. 3. Check if there is no parameter error? 4. Check if there is no trouble on the USB Cable? 5. Replace the USB Cable. 6. Replace the Main PCB with a new one.

Code: 203
Display: ERROR 203 Ment Command
Description: Maintenance command Operation of a maintenance command fails *Non-disclosed command Parameter Up/Download and time setting (LcAeMent [M0xfe])
Troubleshooting Guides: 1. Check the PRM file. 2. Check the number of each parameter. (if PRM matches up to the machine.)

Code: 303
Display: SYSTEM HALT (*) 303 : PCB MAIN ET
Description: Main PCB Ethernet IC trouble
Troubleshooting Guides: 1.Replace the Main PCB with a new one.

Code: 304
Display: ERROR 304 USB INIT ERR
Description: USB initialization error (Failures in initializing USB device)
Troubleshooting Guides: 1. Check if there is no parameter error? 2. Replace the USB Cable. 3. Replace the Main PCB with a new one.

Code: 305
Display: ERROR 305 USB TIME OUT
Description: USB time-out (Occurrence of time-out error on USB device)
Troubleshooting Guides: 1. Check if there is no parameter error? 2. Replace the USB Cable. 3. Replace the Main PCB with a new one.

Code: 401
Display: ERROR 401 MOTOR X
Description: X Servo error (Excessive load to the X-motor)
Troubleshooting Guides: 1. Check if there is no error on the print data. (Check if the same error occurs on other data?) 2. Check if it moves to the X-direction smoothly in the power-off condition. 3. Make sure no torsion on the X-bar or Y-bar. 4. Check if there is no trouble on the Timing Belt. 5. Check if there is no trouble on the Motor Cable. (disconnecting, burnout, or the like) 6. Check the FFC between each PCB and Shortconnectors connected on the PCB. 7. Replace the X-axis Motor with a new one.

Code: 402
Display: ERROR 402 MOTOR Y
Description: Y Servo error (Excessive load to the Y-motor)
Troubleshooting Guides: 1. Check if there is no error on the print data. (Check if the same error occurs on other data?) 2. Check if it moves to the Y-direction smoothly in the power-off condition. 3. Check if there is no trouble on the Timing Belt. 4. Check if there is no trouble on the Motor Cable. (disconnecting, burnout, or the like) 5. Check the FFC between each PCB and Shortconnectors connected on the PCB. 6. Replace the Y-axis motor with a new one.

Code: 403
Display: ERROR 403 X CURRENT
Description: X-motor current (Over current error of X-motor is detected.)
Troubleshooting Guides: 1. Check if there is no error on the print data. (Check if the same error occurs on other data?) 2. Check if it moves to the X-direction smoothly in the power-off condition. 3. Make sure no torsion on the X-bar or Y-bar. 4. Check if there is no trouble on the Timing Belt. 5. Check if there is no trouble on the Motor Cable. (disconnecting, burnout, or the like) 6. Check the FFC between each PCB and Shortconnectors connected on the PCB. 7. Replace the X-axis Motor with a new one.

Code: 404
Display: ERROR 404 Y CURRENT
Description: Y-motor current (Over current error of Y-motor is detected.)
Troubleshooting Guides: 1. Check if there is no error on the print data. (Check if the same error occurs on other data?) 2. Check if it moves to the Y-direction smoothly in the power-off condition. 3. Check if there is no trouble on the Timing Belt. 4. Check if there is no trouble on the Motor Cable. (disconnecting, burnout, or the like) 5. Check the FFC between each PCB and Shortconnectors connected on the PCB. 6. Replace the Y-axis motor with a new one.

Code: 406
Display: SYSTEM HALT (*) 406 : WIPER ORG
Description: Wiper origin undetectable
Troubleshooting Guides: 1. Execute and confirm [#TEST]->[SENSOR TEST] -> [WIPER-ORG]. (Confirm that the ON/OFF display is switched by moving the wiper back and forth.) 2. Check that the wiper moves back and forth smoothly in manual. 3. Check the assembly and connector connection of Wiper Origin Sensor. 4. Check the connector connection of Y-origin Sensor 5. Check the connections between the Pump III PCB and the SL-Relay PCB, and then disconnect and connect the FFCs. 6. Replace the Wiper Back/Forth Origin Sensor with a new one. 7. Replace the Wiper Motor with a new one. 8. Replace the FFC located between the Pump III PCB and the SL-Relay PCB. 9. Replace the Pump III PCB with a new one. 10. Replace the SL-Relay PCB with a new one.

Code: 40b
Display: SYSTEM HALT (*) 40b : UN MAGNETIC
Description: DC motor is driving without excited
Troubleshooting Guides: 1.Update F/W. 2. Upload the parameter and initialize parameter with #PARAMETER. 3. Replace the Main PCB with a new one.

Code: 420
Display: ERROR 420 Z POSITION
Description: Z-axis of coordinate is misaligned.
Troubleshooting Guides: 1. Check the weight of a work on the table. 2. Check the parameters. 3. Check the Tabel mechanism. (including rattling, loosening of screws, or smooth motion) 4. Check if there is no trouble on the Z Origin Sensor. 5. Replace the Z Origin sensor with a new one. 6. Replace the 3042 Station3 PCB with a new one.

Code: 421
Display: ERROR 421 !CHECK FILTER
Description: Gives warning of filter blot. • Mist absorption filter • UV mist filter
Troubleshooting Guides: 1. Perform [MAINTENANCE] -> [STATION MENT: CHECK FILTER] and replace the “Mist absorption filter” and the “UV mist filter”.

Code: 502
Display: SYSTEM HALT (*) 502 : Y ORGIN
Description: Y Origin Sensor error
Troubleshooting Guides: 1. Execute and confirm [#TEST]->[SENSOR TEST] -> [Y-ORG]. (Confirm that the ON/OFF display is switched by moving the carriage left and right.) 2. Check in manual if the carriage moves left and right smoothly. 3. Check the connector connection of Y-origin Sensor and then disconnect and connect the cabel. 4. Replace the Y Origin Sensor with a new one. 5. Check if there is no trouble on theY Motor Cable. (disconnecting, burnout, or the like) 6. Replace the Y-axis motor with a new one. 7. Replace the Slider PCB with a new one. 8. Replace the SL-Relay PCB with a new one. 9. Replace the Main PCB with a new one.

Code: 505
Display: ERROR 505 !WORK High
Description: The Work Area Sensor detected an obstacle that can hit the head.
Troubleshooting Guides: Lower the table until this warning disappears. If this warning does not disappear when the table is lowered to the bottom. 1. Execute and confirm [#TEST]->[SENSOR TEST] – >[HEIGHT-SES]. 2. Readjust the Work Area Sensor. 3. Readjust the height of the carriage. 4. Check the Connectors of Work Area Sensor connected on the PCB 5. Replace the Work Area Sensor with a new one. 6. Replace the SL-Relay PCB with a new one. 7. Replace the Pump 3 PCB with a new one.

Code: 509
Display: ERROR 509 HDC POSCNT
Description: HDC position counter error
Troubleshooting Guides: 1. Execute and confirm [#TEST]->[SENSOR TEST] – >[Y-ORG].(Confirm that the ON/OFF display is switched by moving the carriage left and right.) 2. [Execute [#TEST]->[CHECK ENCODER]. 3. Check the assembly of Y-scale, and confirm that there is neither dirt nor scratch. 4. Check in manual if the Head Assy. (carriage) moves left and right smoothly. 5. Check the connector connection of Y-origin Sensor and Linear Encoder. 6. Replace the Y-origin Sensor or Linear Encoder with a new one. 7. Check the assembly and connector connection of Yaxis Motor. 8. Replace the Y-axis Motor with a new one. 9. Replace the Slider PCB with a new one. 10. Replace the SL-Relay PCB with a new one. 11.Replace the Main PCB with a new one.

Code: 509
Display: SYSTEM HALT (*) 509 : HDC POSCNT
Description: HDC position counter error
Troubleshooting Guides: 1. [Execute and confirm [#TEST]->[SENSOR TEST] – >[Y-ORG].(Confirm that the ON/OFF display is switched by moving the carriage left and right.) 2. [Execute [#TEST]->[CHECK ENCODER]. 3. Check the assembly of Y-scale, and confirm that there is neither dirt nor scratch. 4. Check in manual if the Head Assy. (carriage) moves left and right smoothly. 5. Check the connector connection of Y-origin Sensor and Linear Encoder. 6. Replace the Y-origin Sensor or Linear Encoder with a new one. 7. Check the assembly and connector connection of Yaxis Motor. 8. Replace the Y-axis Motor with a new one. 9. Replace the Slider PCB with a new one. 10. Replace the SL-Relay PCB with a new one. 11.Replace the Main PCB with a new one.

Code: 50a
Display: ERROR 50a Y ORIGIN
Description: Y-origin error (Origin of Y-axis can not be detected)
Troubleshooting Guides: 1. Execute and confirm [#TEST]->[SENSOR TEST] – >[Y-ORG].(Confirm that the ON/OFF display is switched by moving the carriage left and right.) 2. [Execute [#TEST]->[CHECK ENCODER]. 3. Check in manual if the Head Assy. (carriage) moves left and right smoothly. 4. Check the connector connection of Y-origin Sensor and Linear Encoder. 5. Replace the Y-origin Sensor or Linear Encoder with a new one. 6. Check the assembly and connector connection of Yaxis Motor. 7. Replace the Y-axis Motor with a new one. 8. Replace the Slider PCB with a new one. 9. Replace the SL-Relay PCB with a new one. 10. Replace the Main PCB with a new one.

Code: 50f
Display: ERROR 50f L-SCALE BLACK
Description: Liner Scale error
Troubleshooting Guides: 1. Check the assembly position of Linear Scale and Encoder PCB Assy.. 2. Check Linear Scale (scratches or dirtiness or so.) 3. Replace the Linear Scale with a new one. 4. Replace the Encoder PCB Assy. with a new one.

Code: 510
Display: ERROR 510 X ORIGIN
Description: X-origin error (Origin of X-axis can not be detected)
Troubleshooting Guides: 1. Execute and confirm [#TEST]->[SENSOR TEST]-> [X-ORG]. 2. Check the connection of connector of the X-origin Sensor. 3. Replace the X-origin Sensor with a new one. 4. Check the assembly and connector connection of Xaxis Motor.B. 5. Replace the X-axis Motor with a new one. 6. Replace the Main PCB with a new one.

Code: 510
Display: SYSTEM HALT (*) 510 : X ORGIN
Description: X-origin error (Origin of X-axis can not be detected)
Troubleshooting Guides: 1. Execute and confirm [#TEST]->[SENSOR TEST]-> [X-ORG]. 2. Check the connection of connector of the X-origin Sensor. 3. Replace the X-origin Sensor with a new one. 4. Check the assembly and connector connection of Xaxis Motor.B. 5. Replace the X-axis Motor with a new one. 6. Replace the Main PCB with a new one.

Code: 511
Display: ERROR 511 Z ORIGIN
Description: Z-origin error (Origin of Z-axis can not be detected)
Troubleshooting Guides: 1. Execute and confirm [#TEST]->[SENSOR TEST]-> [TBL-ORG]. 2. Check the connection of connector of the Z-origin Sensor. 3. Replace the Z-origin Sensor with a new one. 4. Disconnect and connect the connector of the ZMotor( Stepping motor). 5. Replace the Station III PCB with a new one.

Code: 511
Display: SYSTEM HALT (*) 511 : Z ORGIN
Description: Z-origin error (Origin of Z-axis can not be detected)
Troubleshooting Guides: 1. Execute and confirm [#TEST]->[SENSOR TEST]-> [TBL-ORG]. 2. Check the connection of connector of the Z-origin Sensor. 3. Replace the Z-origin Sensor with a new one. 4. Disconnect and connect the connector of the ZMotor( Stepping motor). 5. Replace the Station III PCB with a new one.

Code: 601
Display: ERROR 601 INK NEAREND
Description: Ink near end (A small amount of ink left)
Troubleshooting Guides: (When the message is still displayed even after a new Ink Cartridge or an empty Ink Cartridge is charged;) 1. Execute and confirm [#TEST]->[SENSOR TEST]-> [INK NEND1](The number meets the cartridge No.). 2. Check the peripheral and the assembly of the End Sensor. 3. Check the connection of the Presence Sensor and the Near End Sensor. 4. Replace the Cartridge with a new one 5. Replace the Presence/Near End Sensor with a new one. 6. Replace the SL-Relay PCB with a new one. 7. Replace the Main PCB with a new one.

Code: 602
Display: ERROR 602 INK END
Description: Ink end (No ink left)
Troubleshooting Guides: (If this message appears when a new cartridge or a cartridge with enough ink is set) 1. Execute and confirm [#TEST]->[SENSOR TEST]-> [INK NEND1](The number meets the cartridge No.). 2. Check the peripheral and the assembly of the End Sensor. 3. Check the connection of the Presence Sensor and the End Sensor. 4. Replace the Cartridge with a new one. 5. Replace the Presence / Near End Sensor with a new one. 6. Replace the SL-Relay PCB with a new one. 7. Replace the Main PCB with a new one.

Code: 603
Display: ERROR 603 NO CARTRDG
Description: No cartridge (Cartridge is not installed)
Troubleshooting Guides: (When the message is still displayed even after a Ink Cartridge is charged;) 1. Execute and confirm [#TEST]->[SENSOR TEST]-> [INK1](The number meets the cartridge No.).. 2. Check the peripheral and the assembly of the Presence Sensor. 3. Check the connection of the Presence Sensor and the End Sensor 4. .Replace the Cartridge with a new one 5. Replace the Presence/Near End Sensor with a new one. 6. Replace the SL-Relay PCB with a new one. 7. Replace the Main PCB with a new one. (Refer to 3.3.

Code: 605
Display: ERROR 605 !CLEANING WIPER
Description: Wiper lifetime (Wiping times exceeding the specified number.) 1),Wiping times (Ink parameter 1 No45 WipeCnt) Wiping time is cleared when the following is executed: [FUNCTION MAINTENANCE]- >[STATION]->[MENT:WIPER EXCHG] 2),Specified number :Wiper life (Ink parameter 2 No58 WIPElmt) x Wiper replacement level
Troubleshooting Guides: 1. Execute [FUNCTION MAINTENANCE]- >[STATION]->[MENT:WIPER CLEANING] to clean the wiper. 2. Replace the Main PCB with a new one.

Code: 606
Display: ERROR 606 WRONG CARTRIDGE
Description: The IC chip of the ink cartridge is not read properly.
Troubleshooting Guides: (If this message appears when a correct cartridge is set) 1. Check the assembly of the ID Contact PCB and the shape of the contact plate, and execute the cleaning. 2. Check the connection of the ID Contact PCB. 3. Replace the Cartridge with a new one 4. Replace the ID Contact PCB Assy. with a new one. 5. Replace the SL-

Code: 607
Display: ERROR 607 CAP CLEANING
Description: Warning for cleaning around the cap (A specified number of flushing on the cap exceeded.) 1),Capcleaning counter (Ink parameter 1 No04 CapClean) Counter is cleared when the following is executed: [FUNCTION MAINTENANCE]- >[STATION]->[MENT:CARRIAGE OUT] 2),Specified number of the Capcleaning : warning level 100×2^(Ink parameter 2 No.66 Cap.LM -1)
Troubleshooting Guides: 1. Clean the cap. (If this message appears after cleaning the cap) 2. Replace the Main PCB with a new one.

Code: 608
Display: ERROR 608 CARTRIDGE
Description: Ink is tried to fill with unusable cartridge installed.
Troubleshooting Guides: 1. Check the type of the ink cartridge. Execute the followings if the type of the ink cartridge is correct. 2. Check the assembly of the ID Contact PCB and the shape of the contact plate, and execute the cleaning. 3. Check the connection of the ID Contact PCB. 4. Replace the Cartridge with a new one 5. Replace the ID Contact PCB Assy. with a new one. 6. Replace the SL-Relay PCB with a new one.

Code: 60b
Display: ERROR 60b WIPER BOTTLE
Description: Wiper bottle warning A great deal of ink is in the Wiper Bottle. Displayed when the Wiper Nozzle Suction Pump exceeds the 2,500 times [Fixed]. Wiper Pump suction times: Ink parameter 1 No47 [Wipe Pump ]
Troubleshooting Guides: 1. Select [FUNCTION MAINTENANCE]->[STATION]- >[MENT:WIPER BOTTLE] and dispose of ink in the Wiper Bottle.

Code: 60c
Display: ERROR 60c INK TYPE
Description: Type of inserted Ink Cartridge is different.
Troubleshooting Guides: 1. Check the type of the ink cartridge. Execute the followings if the type of the ink cartridge is correct. 2. Check the assembly of the ID Contact PCB and the shape of the contact plate, and execute the cleaning. 3. Check the connection of the ID Contact PCB. 4. Replace the Cartridge with a new one 5. Replace the ID Contact PCB Assy. with a new one. 6. Replace the SL-Relay PCB with a new one.

Code: 60d
Display: ERROR 60d REMAIN INK
Description: Remaining ink is not enough to execute cleaning or to fill ink.
Troubleshooting Guides: Replace the Cartridge with a new one

Code: 60e
Display: ERROR 60e NOT COMPLETE FUP
Description: Ink is not filled into some heads.
Troubleshooting Guides: Fill ink into unfilled heads.

Code: 60f
Display: ERROR 60f Expiration
Description: Some ink cartridges are expired.
Troubleshooting Guides: 1. Check the expiration date of the ink. (If this message appears when a correct cartridge is set) 2. Check the assembly of the ID Contact PCB and the shape of the contact plate, and execute the cleaning. 3. Check the connection of the ID Contact PCB. 4. Replace the Cartridge with a new one. 5. Replace the ID Contact PCB Assy. with a new one. 6. Replace the SL-Relay PCB with a new one.

Code: 610
Display: ERROR 610 NOT FILLUP
Description: Ink is not filled into all the heads.
Troubleshooting Guides: Fill ink to all the heads.

Code: 611
Display: ERROR 611 Case Weight
Description: ‘CASE WEIGHT’ of 600ml cartridge is not set.
Troubleshooting Guides: Set ‘CASE WEIGHT’ for ‘600ml CARTRIDGE’ of ‘MACHINE SET’.

Code: 612
Display: ERROR 612 INK LVL LOW
Description: Remaining amount of ink became less.
Troubleshooting Guides: Enter the cartridge weight from ‘CART WEIGHT’ menu of ‘SET UP’.

Code: 613
Display: ERROR 613 INK LVL END
Description: Remaining amount of ink became none.
Troubleshooting Guides: • If ink remains, enter the cartridge weight from ‘CART WEIGHT’ menu of ‘SET UP’. • If ink does not remain, replace it with a new cartridge.

Code: 614
Display: ERROR 614 Preservation Failure
Description: Remaining amount of ink was failed to be written.
Troubleshooting Guides: 1. Pull the cartridge out and then insert it to write it again. 2. If the error cannot be solved, replace it with a new cartridge.

Code: 615
Display: ERROR 615 Cartridge Weight
Description: The cartridge weight was not entered.
Troubleshooting Guides: Enter the cartridge weight.

Code: 702
Display: ERROR 702 THERMISTOR
Description: Defective of the thermistor (disconnection or short)
Troubleshooting Guides: 1. Check each thermistor. 2. Replace the Main PCB with a new one.

Code: 705
Display: ERROR 705 WATER LACK
Description: Water in the cooling water buffer tank is low.
Troubleshooting Guides: 1. Check amount of water in the cooling water buffer tank, and replace the Nonfreezing fluid mixture water if lacking. 2. If water decreases quickly, check water leakage from the cooling water path (a tube or a radiator). • Execute [#TEST SENSOR TEST]->[CoolFloat] to check the sensor operation. 3. Check the assembly of the Float Sensor and the connector connection. 4. Replace the Float Sensor and the Cable with a new one. 5. Replace the SL-Relay PCB with a new one.

Code: 706
Display: ERROR 706 UV UNIT OVER HEAT
Description: Temperature in the UV unit is above its specification.
Troubleshooting Guides: 1. Check connection and operation of the radiator fan and the UV unit fan. 2. Check the operation of the water cooling pump. 3. Check water level of the cooling water buffer tank and a path of the cooling water. 4. Check the connection of connector of the LED UV UNIT Assy and the Slider PCB. 5. Replace the LED UV UNIT Assy with a new one. 6. Replace the Slider PCB with a new one. 7. Replace the SL-Relay PCB with a new one.

Code: 707
Display: ERROR 707 !HD HEATER BRK
Description: Is the heater of the head disconnected? (The temperature does not rise after heating for over a certain period of time.)
Troubleshooting Guides: 1. Check the room temperature is not too low. 2. Replace the Print Head with a new one. 3. Replace the Slider PCB with a new one.

Code: 708
Display: ERROR 708 UV THERMISTOR BRK
Description: The thermistor in the UV unit (Temperature sensor) is disconnected.
Troubleshooting Guides: 1. Check the connection of connector of the LED UV UNIT Assy and the Slider PCB. 2. Replace the LED UV UNIT Assy with a new one. 3. Replace the Slider PCB with a new one.

Code: 70a
Display: ERROR 70a LED UV CURRENT
Description: The LED UV unit has been broken. Or, the detected current is abnormal.
Troubleshooting Guides: 1. Replace the LEDUVx2-DRIVE PDB Assy with a new one. 2. Replace the LEDUV Irradiation Assy with a new one.

Code: 801
Display: SYSTEM HALT (*) 801 : (C)OPCODE
Description: System error (CPU exception: OP code error)
Troubleshooting Guides: 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one.

Code: 802
Display: SYSTEM HALT (*) 802 : (C)SLOT
Description: System error (CPU exception: Slot instruction error)
Troubleshooting Guides: 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one.

Code: 803
Display: SYSTEM HALT (*) 803 : (C)CPU ADDR
Description: System error (CPU exception: CPU address error)
Troubleshooting Guides: 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one.

Code: 804
Display: SYSTEM HALT (*) 804 : (C)DMA ADDR
Description: System error (CPU exception: DMA address error)
Troubleshooting Guides: 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one.

Code: 805
Display: SYSTEM HALT (*) 805 : (C)ZERO DIV
Description: System error (CPU exception: Division by 0)
Troubleshooting Guides: 1. Check the peripheral temperature of Main PCB, and then check if the error is caused by the thermo runaway of CPU. 2. Make sure that there is no device generating strong radio wave in the vicinity. 3. Replace the Main PCB with a new one. 4. Replace the Power Supply PCB with a new one.

Code: 806
Display: SYSTEM HALT (*) 806 : FW/SIO bit
Description: FW error (Serial control F/W error (bit control))
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 807
Display: SYSTEM HALT (*) 807 : FW/SIO wbsy
Description: FW error (Serial control F/W error (WR BUSY))
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 808
Display: SYSTEM HALT (*) 808 : FW/STP-MTR
Description: FW error (Step Motor stop waiting)
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 809
Display: SYSTEM HALT (*) 809 : FW/XY param
Description: FW error (XY-axis Motor resolution conversion parameter error)
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 80a
Display: SYSTEM HALT (*) 80a : FW/Y RANGE
Description: FW error (Y movable range error)
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 80b
Display: SYSTEM HALT (*) 80b : FW/ctrltsk
Description: FW error (Motor control task error)
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 80c
Display: SYSTEM HALT (*) 80c : FW/PUMP W
Description: FW error (Suction Pump stop waiting time over at capping)
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 80d
Display: SYSTEM HALT (*) 80d : FW/SERVO IT
Description: FW error (Servo interruption error)
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 80e
Display: SYSTEM HALT (*) 80e : FW/FROM prm
Description: FW error (FROM PARAM error (F/W BUG))
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 80f
Display: SYSTEM HALT (*) 80f : FW/SIO vch FW error (Virtual serial CH setting error)
Description: FW error (Virtual serial CH setting error)
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 810
Display: SYSTEM HALT (*) 810 : FW/KEY RDI
Description: FW error (No keyboard RDI)
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 811
Display: SYSTEM HALT (*) 811 : FW/SIO read
Description: FW error (Serial control F/W error (RD BUSY))
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 812
Display: SYSTEM HALT (*) 812 : FW/CRTRG NO
Description: FW error (Cartridge number error)
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 813
Display: SYSTEM HALT (*) 813 : FW/WIPER RN
Description: FW error (Wiper operation range error)
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 814
Display: SYSTEM HALT (*) 814 : FW/drivinfm
Description: FW error (drivinfm() information obtaining error
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 815
Display: SYSTEM HALT (*) 815 : FW/SIO rsrc
Description: FW error (Serial control F/W error (material control))
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 816
Display: SYSTEM HALT (*) 816 : FW/FROM WRC
Description: FW error (FROM write control error)
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 817
Display: SYSTEM HALT (*) 817 : FW/SaveArea
Description: FW error (Save area error (size over))
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 818
Display: SYSTEM HALT (*) 818 : FW/EEP SIZE
Description: FW error (EEPROM size over)
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 819
Display: SYSTEM HALT (*) 819 : FW/HROM SIZ
Description: FW error (HDROM size over)
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 81a
Display: SYSTEM HALT (*) 81a : FW/FROM SIZ
Description: FW error (FROM size over)
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 81b
Display: SYSTEM HALT (*) 81b : FW/STACK OV
Description: FW error (STACK OVER)
Troubleshooting Guides: 1. Update F/W. 2. Check and clear the parameter. 3. Disconnect and connect the FFC located between the Main PCB and the SL-Relay PCB. 4. Disconnect and connect the FFC located between the Main PCB and the Station III PCB. 5. Disconnect and connect the FFC located between the SL-Relay PCB and the Slider PCB. 6. Replace the FFC located between the Main PCB and the SL-Relay PCB. 7. Replace the FFC located between the Main PCB and the Station III PCB. 8. Replace the FFC located between the SL-Relay PCB and the Slider PCB. 9. Replace the Main PCB with a new one.

Code: 901
Display: ERROR 901 OPERATION
Description: The operation panel is incorrectly operated. (Example: Test drawing was executed without ink filled.)
Troubleshooting Guides: Explain a user the operation method. (Carry out the followings if the error still occurs) 1. Execute and confirm [#TEST]->[KEYBOARD]. (Check that there is no hang-up nor subduction on Key Tops at the same time.) 2. Disconnect and connect the FFC located between the Keyboard PCB and the Main PCB. 3. Replace the Keyboard FFC (Keyboard PCB ~ the Main PCB). 4. Replace the Keyboard PCB with a new one. 5. Replace the Main PCB with a new one.

Code: 902
Display: ERROR 902 DATA REMAIN
Description: Drawing data is remaining.
Troubleshooting Guides: (Carry out the followings if the error still occurs when data is cleared.) 1. Check errors in the parameter. 2. Remove USB cable from the printer and execute data clear. -> If solved, it is a problem on USB cable or PC. 3. Replace the USB Cable with a new one. 4. Replace the Main PCB with a new one.

Code: 90d
Display: ERROR 90d NO HEAD SELECT
Description: Loaded number of the head is assumed zero.
Troubleshooting Guides: Check the setting of loading number of the head in the parameter. (System parameter No.41 HEAD NO=3)

Code: n01
Display: <LOCAL> NO CARTRDG MCYKWR
Description: No cartridge (Cartridge is not installed)
Troubleshooting Guides: (When the message is still displayed even after a Ink Cartridge is charged;) 1. Execute and confirm [#TEST]->[SENSOR TEST]-> [INK1](The number meets the cartridge No.). 2. Check the peripheral and the assembly of the Presence Sensor. 3. Check the connection of the Presence Sensor and the End Sensor 4. .Replace the Cartridge with a new one 5. Replace the Presence/Near End Sensor with a new one. 6. Replace the SL-Relay PCB with a new one. 7. Replace the Main PCB with a new one.

Code: n02
Display: <LOCAL> INK NEAREND MCYKWR
Description: Ink near end (A small amount of ink left)
Troubleshooting Guides: (When the message is still displayed even after a new Ink Cartridge or an empty Ink Cartridge is charged;) 1. Execute and confirm [#TEST]->[SENSOR TEST]-> [INK NEND1](The number meets the cartridge No.). 2. Check the peripheral and the assembly of the End Sensor. 3. Check the connection of the Presence Sensor and the Near End Sensor. 4. Replace the Cartridge with a new one 5. Replace the Presence/Near End Sensor with a new one. 6. Replace the SL-Relay PCB with a new one. 7. Replace the Main PCB with a new one.

Code: n02
Display: <LOCAL> INK END MCYKWR
Description: Ink end (No ink left)
Troubleshooting Guides: (If this message appears when a new cartridge or a cartridge with enough ink is set) 1. Execute and confirm [#TEST]->[SENSOR TEST]-> [INK NEND1](The number meets the cartridge No.). 2. Check the peripheral and the assembly of the End Sensor. 3. Check the connection of the Presence Sensor and the End Sensor. 4. Replace the Cartridge with a new one. 5. Replace the Presence / Near End Sensor with a new one. 6. Replace the SL-Relay PCB with a new one. 7. Replace the Main PCB with a new one.

Code: n03
Display: <LOCAL> Expiration MCYKWR
Description: Some ink cartridges are expired.
Troubleshooting Guides: 1. 1. Check the expiration date of the ink. (If this message appears when a correct cartridge is set) 2. Check the assembly of the ID Contact PCB and the shape of the contact plate, and execute the cleaning. 3. Check the connection of the ID Contact PCB. 4.Replace the Cartridge with a new one. 5. Replace the ID Contact PCB Assy. with a new one. 6. Replace the SL-Relay PCB with a new one.

Code: n04
Display: <LOCAL> INK TYPE MCYKWR
Description: Type of inserted Ink Cartridge is different.
Troubleshooting Guides: 1. Check the type of the ink cartridge. Execute the followings if the type of the ink cartridge is correct. 2. Check the assembly of the ID Contact PCB and the shape of the contact plate, and execute the cleaning. 3. Check the connection of the ID Contact PCB. 4.Replace the Cartridge with a new one 5. Replace the ID Contact PCB Assy. with a new one. 6. Replace the SL-Relay PCB with a new one.

Code: n05
Display: <LOCAL> ColorofINK MCYKWR
Description: The color of Ink Cartridge inserted is different from the color to be set.
Troubleshooting Guides: 1. Check the type of the ink cartridge. Execute the followings if the type of the ink cartridge is correct. 2. Check the assembly of the ID Contact PCB and the shape of the contact plate, and execute the cleaning. 3. Check the connection of the ID Contact PCB. 4.Replace the Cartridge with a new one 5. Replace the ID Contact PCB Assy. with a new one. 6. Replace the SL-Relay PCB with a new one.

Code: n06
Display: <LOCAL> NON-ORIGNL MCYKWR
Description: Non-MIMAKI genuine Ink Cartridge charged
Troubleshooting Guides: 1. Check the type of the ink cartridge. Execute the followings if the type of the ink cartridge is correct. 2. Check the assembly of the ID Contact PCB and the shape of the contact plate, and execute the cleaning. 3. Check the connection of the ID Contact PCB. 4.Replace the Cartridge with a new one 5. Replace the ID Contact PCB Assy. with a new one. 6. Replace the SL-Relay PCB with a new one.

Code: n07
Display: <LOCAL> WRONG INK IC MCYKWR
Description: IC chip of Ink Cartridge unreadable properly
Troubleshooting Guides: 1. Check the type of the ink cartridge. Execute the followings if the type of the ink cartridge is correct. 2. Check the assembly of the ID Contact PCB and the shape of the contact plate, and execute the cleaning. 3. Check the connection of the ID Contact PCB. 4.Replace the Cartridge with a new one 5. Replace the ID Contact PCB Assy. with a new one. 6. Replace the SL-Relay PCB with a new one.

Code: n08
Display: <LOCAL> !WORK High
Description: The Work Area Sensor detected an obstacle that can hit the head.
Troubleshooting Guides: Lower the table until this warning disappears. If this warning does not disappear when the table is lowered to the bottom. 1. Execute and confirm [#TEST]->[SENSOR TEST] ->[HEIGHTSES]. 2. Readjust the Work Area Sensor. 3. Readjust the height of the carriage. 4. Check the Connectors of Work Area Sensor connected on the PCB 5. Replace the Work Area Sensor with a new one. 6. Replace the SL-Relay PCB with a new one. 7. Replace the Pump 3 PCB with a new one.

Code: n09
Display: <LOCAL> WATER LACK
Description: Water in the cooling water buffer tank is low.
Troubleshooting Guides: 1. Check amount of water in the cooling water buffer tank, and replace the Nonfreezing fluid mixture water if lacking. 2. If water decreases quickly, check water leakage from the cooling water path (a tube or a radiator). •Execute [#TEST SENSOR TEST]->[CoolFloat] to check the sensor operation. 3. Check the assembly of the Float Sensor and the connector connection. 4. Replace the Float Sensor and the Cable with a new one. 5. Replace the SL-Relay PCB with a new one.

Code: n10
Display: <LOCAL> !WS INKTANK CHK
Description: A great deal of ink is in the Wast ink tank
Troubleshooting Guides: 1. Check the Wast ink tank. 2. Select [FUNCTION MAINTENANCE]->[STATION]- >[MENT:WASTE TANK] and dispose of ink in the Wast ink tank.

Code: n11
Display: <LOCAL> WIPER BOTTLE
Description: A great deal of ink is in the Wiper Bottle.
Troubleshooting Guides: 1. Check the Wiper Bottle. 2. Select [FUNCTION MAINTENANCE]->[STATION]- >[MENT:WIPER BOTTLE] and dispose of ink in the Wiper Bottle.

Code: n12
Display: <LOCAL> CLEANING WIPER
Description: Wiping times exceeding the specified number.
Troubleshooting Guides: 1. Execute [FUNCTION MAINTENANCE]->[STATION]- >[MENT:WIPER CLEANING] to clean the wiper.

Code: n13
Display: <LOCAL> !CHECK FILTER
Description: A filter may be stained.
Troubleshooting Guides: 1. Check the filter. 1. Execute [FUNCTION MAINTENANCE]->[STATION]- >[MENT:CHECK FILTER] to replace the filter..

Code: n14
Display: <LOCAL> CAP CLEANING
Description: Warning for cleaning around cap (Flushing times on the cap exceeded the specified number.)
Troubleshooting Guides: 1. Execute [STATION] -> [MENT: CARRIAGE OUT] to clean the cap.

Code: n15
Display: <LOCAL> Case Weight
Description: [CASE WEIGHT] of 600ml CARTRIDGE was not set.
Troubleshooting Guides: 1. Set [CASE WEIGHT] from [MACHINE SET] -> [600ml CARTRIDGE].

Code: n16
Display: <LOCAL> INK LVL LOW
Description: The remaining amount of ink became less.
Troubleshooting Guides: 1. Enter the cartridge weight from [CART WEIGHT] menu of [SET UP].

Code: n17
Display: <LOCAL> INK LVL END
Description: Remaining amount of ink became none.
Troubleshooting Guides: • If ink remains, enter the cartridge weight from ‘CART WEIGHT’ menu of ‘SET UP’. ¡E If ink does not remain, replace it with a new cartridge.

Code: n18
Display: <LOCAL> !CHECK LED UV LEVEL
Description:
Troubleshooting Guides: 1. Check the illuminance of the LED UV lamp. If it is less than the specified value, replace the lamp.

Code: n19
Display: <LOCAL> Preservation Failure
Description: Remaining amount of ink was failed to be written.
Troubleshooting Guides: 1. Pull the cartridge out and then insert it to write it again. 2. If the error cannot be solved, replace it with a new cartridge.

Code: n20
Display: <LOCAL> Cartridge Weight
Description: The cartridge weight was not entered.
Troubleshooting Guides: 1. Enter the cartridge weight.

Waste Ink Pad Counter Utility Functions:

– Cleaning printhead.
– Ink charge.
– Fix Epson red lights blinking Error

– Fix Epson Service Required Error: A printer’s ink pad at the end of its service life Please contact Epson Support.

– Check the current value of waste ink counters and ink level counters.
– Clear Waste Ink Counters.
– Read and write serial number.
– Read and write USB ID.
– Read and write HEAD ID.
– Make EEPROM dump, backup.
– Paper feed test.
– Nozzle check.
– Color check pattern.
– Initialize (disable) PF deterioration offset.
– Retrieve device information

Contact us to get support with Mimaki UJF6042 Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/

Источник

hand851

Roland Mutoh & Mimaki inks digiprint-parts.com

Error Codes List page 16

Error Codes List page 16

Ошибка Mimaki JV33-160 BS

Кто сейчас на конференции

TS330-1600 Блок подачи чернил 10 кг

Меры предосторожности

Предупреждение об использовании

Меры предосторожности

Предупреждающие надписи

Название каждой части

О коррекции уровня чернил

Обслуживание

Если возникает аномалия

Документы / Ресурсы

Рекомендации

Fixing Mimaki UJF6042 Error Codes list

Waste Ink Pad Counter Utility Functions:

Contact us to get support with Mimaki UJF6042 Error case