Riso ошибка t11

Type
Point
Description
A01
201
Master-positioning sensor does not go ON even after the write pulse motor is activated during the master-positioning, master-cut, or master-loading operation.
A01
202
Master-positioning sensor does not go OFF even when the write pulse motor is reversed during the master-positioning or at start of master-making operation.
A01
206
Timeout error during master-making operation
A01
211
Master-positioning sensor is ON during standby.
A01
214
Master-positioning sensor is ON at the start of master making.
A01
215
Faulty gate-array control for the write pulse motor (motor does not stop within set time)
A02
509
Master-loading sensor was OFF when the master was checked at a specified drum angle during the master-loading operation.
A04
303
Master-disposal jam sensor was OFF at both 120 and 180 degrees drum angle.
A04
314
Master-disposal error (recovery error).
A05
304
Master-disposal jam sensor was ON at the completion of the master-disposal operation.
A05
312
The master-disposal jam sensor was ON at the start of master-making operation.
A05
315
The master-disposal jam sensor was ON when the master disposal box was set in the machine.
A06
403
Paper-feed-tray upper or lower safety switch is OFF.
A07
409
Paper-ejection sensor was OFF when the paper should have arrived, and the paper sensor was ON when the machine stopped (Paper misfeed).
A07
412
Paper sensor was OFF three times in succession when a paper misfeed was detected (paper misfeed).
A07
413
Paper sensor was ON when the paper should have left the paper sensor (long-length paper mode error).
A07
418
The paper sensor was ON at the start of machine operation when the START button was pressed.
A07
429
Paper feed error (recovery error).
A07
432
Paper sensor was ON when the machine went into paper feed retry movement after a paper misfeed.
A08
410
Paper-ejection sensor was OFF when paper should have arrived, and the paper sensor was OFF when the machine stopped (paper jam on the print drum).
A08
421
Paper sensor was ON when the paper should have left the paper sensor during feeding of long paper in long-length paper mode (paper longer than 555 mm).
A08
430
Paper jam on print drum (recovery error).
A09
411
Paper-ejection sensor was ON when the paper should have left the paper-ejection sensor.
A09
417
Paper-ejection sensor was ON at the start of machine operation when the START button was pressed.
A09
431
Paper-ejection error (recovery error).
A10
102
Original-registration-sensor remaining jam
A10
103
Original-IN-sensor remaining jam
A10
105
Original-registration-sensor non-arrival jam
A10
106
Original-IN-sensor non-arrival jam
A10
107
Original-OUT-sensor non-arrival jam
A10
109
An original feed error occurred, due to opening the AF.
A10
162
No original in AF during AF master making.
A16
525
Waiting for the master to be removed.
A17
209
Cutter home-position switch is OFF at the start of master-making or master-set operation.
A34
218
Request to resetting the master.
B01
730
Keycard counter: No card
B22
721
With the «Tape separation» function set ON, no power is supplied to the job separator when start key is pressed.
B22
727
After cluster-A signal turned ON, BUSY-signal stayed «L» more than 7 seconds (power to job separator was turned OFF while the tape is being ejected.
B23
722
With the «Tape separation» function set ON, no tape detected in the job separator when the start key is pressed.
B23
723
No tape remains in job separator upon completion of the tape-ejection operation.
B24
724
Tape jam detected when the start key is pressed with the «Tape separation» function set to ON.
B24
725
Job separator tape-jam detection signal is «H» within 1,200 milliseconds after the cluster-A signal turns ON (tape misfeed).
B24
726
Job separator tape-jam detection signal is «L» when the BUSY signal changes from «L» to «H» (or after 7 sec. at «L») after the cluster-A signal goes ON (tape misfeed).
B31
916
Network cable is not connected when the machine is powered ON.
B32
917
Communication error on the network.
B32
920
Error detected by Network Interface Card (NIC) — NAK (negative acknowledgement was received).
B33
931
DHCP server is not found with DHCP ON.
B34
919
Error detected on the locally connected printer.
C01
512
The ink sensor did not go ON even when inking was performed for the preset period.
C01
563
Ink remaining amount is zero.
C01
574
Inkless error was detected 5 times consecutively on one same ink bottle.
C02
200
The master end was detected twice in succession at 10-milliseconds intervals during master transport.
C02
240
Master remaining amount is zero
C02
253
Masterless error was detected twice consecutively on one same master-roll.
C03
308
Compression detection position was reached before the master-compression-motor encoder-sensor count reached the specified level, after the master compression motor turned ON in the compression direction.
C03
313
Master removal box full detected by the master removal count.
C04
402
Paper detection sensor is OFF (no paper on the feed tray).
D01
526
Print drum is not set in the machine (drum connection signal, drum safety switch, and drum-lock sensor is OFF.
D01
527
Print drum connection signal is OFF when the print drum was inserted in the machine.
D01
528
Print drum safety switch is OFF when the print drum was inserted in the machine.
D01
529
Print drum lock sensor is OFF when the print drum was inserted in the machine (time-out: 5 seconds).
D01
530
Print drum connection signal does not go OFF within 5 seconds after the print drum safety switch went OFF when the print drum was pulled out.
D02
532
Incorrect print drum is used.
D03
533
Ink cartridge set sensor is OFF.
D04
534
Incorrect ink cartridge is used.
D04
560
Ink TAG is not detected on ink bottle.
D04
561
Ink cartridge communication error (communication with the ink cartridge was interfered by noise).
D04
562
Wrong ink cartridge information.
D04
564
Detected a mismatch in ink cartridge information
D05
210
Master detection sensor is OFF (not detecting master).
D07
310
Disposal-box safety switch is OFF.
D08
224
Master making unit is not set (both the safety switch and lock sensor are OFF).
D08
226
Master making unit safety switch is still OFF when the master making unit is set in position.
D08
227
Master making unit lock sensor is still OFF when the master making unit is set in position (timeout: 5 seconds).
D08
228
Master making unit lock sensor is still ON even after the master making unit safety switch went OFF, when the master making unit was pulled out of the machine.
D09
212
Master-making-unit set sensor is OFF (sensor light path is free).
D11
535
Front cover set switch is OFF.
D13
9
The rear cover is opened (serviceman safety switch is OFF).
D17
236
Incorrect master roll.
D17
237
Master roll undetected.
D17
238
Master roll communication error.
D17
239
Wrong master roll detected.
D17
241
Detected a mismatch in master roll information.
D18
522
Print drum ready for release (solenoid is ON).
D19
223
Master making unit ready for release (solenoid is ON).
D22
540
Error in access to the Drum PCB (unable to read from or write on the Drum PCB).
D22
542
Abnormal data on Drum PCB.
E01
10
Battery voltage was less than 2.5 V when the power was switched ON (weak battery: time to replace battery).
E02
11
Master counter reached the value set for the maintenance call (value set by test mode). [The message appears when either the power is turned ON, the unit is reset, or when the machine operation ended.]
E02
12
Copy counter reached the value set for the maintenance call (value by set test mode). [The message appears when either the power is turned ON, the unit is reset, or when the machine operation ended.]
E02
22
Maintenance counter inside the print drum reached the value set for the maintenance call (value set by test mode). [The message appears when either the power is turned ON, the unit is reset, or when the machine operation ended.]
F01
15
There is no master on the print drum at the start of printing.
F02
18
Paper size does not match with the image size on the print drum at the start of printing.
F03
16
Multi-up was selected using custom size paper.
F05
19
In master making, the print quantity selected is less than the minimum print quantity.
F10
21
Paper size does not match with the size of image on the print drum when test print is selected and activated.
F21
32
Next original is not in placed on AF for multi-up operation.
F22
33
Next original is not placed on flatbed for multi-up operation.
F37
50
Original was set on the AF with book mode selected, when master making is activated.
F50
910
Auto-printer-selection is disabled due to error on linked printer.
F54
923
Auto-printer-selection is disabled due to no paper in the linked printer.
F55
924
Auto-printer-selection is disabled while receiving print data from PC.
F58
927
Cannot print from linked printer (Initializing NET-C).
H1
566
Requesting ink color information input (Ink-TAG related).
H2
567
Requesting print density information input (Ink-TAG related).
H3
568
Requesting test printing print density information input (Ink-TAG related).
H4
242
Requesting master-making density information input (Master-TAG related).
H5
243
Requesting Print density information input (Master-TAG related).
H6
244
Requesting test printing print density information input (Master-TAG related).
P01
520
Main encoder sensor does not go ON/OFF within 10 milliseconds after the main motor activates.
P01
521
B-positioning sensor status does not change even after 3,033 pulses after the main motor activates.
P01
524
Clamp unit is not at the home position while the print drum is in operation (except during master disposal).
P01
537
Print drum failed to stop at position B. (over-run)
P01
538
Print drum is not locked during operation. (Print-drum lock position sensor: OFF)
P02
400
Both the upper and lower limit sensors were ON at the same time.
P02
401
Overload current was detected in the elevator motor.
P02
404
The lower-limit sensor does not go OFF within 2 seconds after the elevator motor operates in the raising direction from the lower-limit position.
P02
405
The upper-limit sensor does not go ON within 12 seconds after the elevator motor operates in the raising direction.
P02
406
The upper-limit sensor does not go OFF within 2 seconds after the elevator motor operates in the lower direction from the upper-limit position.
P02
407
The lower-limit sensor does not go ON within 12 seconds after the elevator motor operates in the lowering direction.
P02
408
The upper-limit sensor is OFF continuously for over 2 seconds during operation of the elevator servo action to raise the feed tray.
P03
500
Clamp sensor A is OFF after the completion of the clamp unit initialization or home positioning movement.
P03
501
Clamp sensor B does not change within 1 second from the time the clamp motor operates in the correct direction.
P03
502
Clamp sensor B does not change within 1 second from the time the clamp motor operates in the reverse direction.
P03
503
Clamp sensor A does not go ON within 3 seconds when the clamp unit makes initialization movement.
P03
504
At the start of Clamp plate open/close action, the the detection sequence of clamp-sensors A & B is abnormal.
P03
505
At the start of print drum Positon-A compensation movement, the detection sequence of clamp-sensors A & B is abnormal.
P03
506
At the start of Clamp unit Home-positioning movement, the detection sequence of clamp-sensors A & B is abnormal.
P03
507
Clamp sensor A is ON after the clamp release action is completed.
P03
508
Clamp sensor A is ON after the A-position compensating movement is completed.
P03
545
Clamp unit is not in the home position while the print drum is in movement (cause due to the clamp motor).
P04
513
The overflow sensor was ON for a set number of times in succession during the 10-millisecond-interval overflow-sensor check.
P05
603
The vertical-centering sensor does not switch ON even when the vertical-positioning pulse motor activated in the image-down direction for 5 seconds during vertical home positioning movement.
P05
604
The vertical-centering sensor does not switch OFF even when the vertical-positioning pulse motor activated in the image-up direction for 5 seconds during vertical home positioning movement.
P05
605
Even though the vertical positioning motor stopped according to the vertical centering sensor detection, the stopping position does not correspond with the programmed position. (GA control error).
P05
612
The one-step-positioning key was pressed with vertical-print-position information undefined.
P08
951
Print job executed was not in correct RisoRinc format.
P11
600
Print pressure HP sensor does not switch ON within 3.9 seconds after the print pressure pulse motor activated towards higher pressure during home positioning operation.
P11
601
Print pressure HP sensor does not switch OFF within 4.6 seconds after the print pressure pulse motor activated towards lower pressure during home positioning operation.
P11
602
Even though the print pressure control pulse motor stopped according to the print pressure HP sensor detection, the stopping position does not correspond with the programmed position. (GA control error).
P12
301
Master compression motor lock when moving compression plate up.
P12
305
Master compression sensor does not go ON within 6.5 seconds after the master compression motor operates in the return direction.
P12
306
Master compression sensor does not go OFF within 2 seconds after the master compression motor operates in the compress direction.
P12
307
Master compression plate maximum position is not detected within 6.5 seconds after the master compression motor operates in the compress direction.
P12
309
Master-compression-motor encoder sensor count did not change as the master compression motor activated in the compress direction and moved out from the home position.
P12
316
Master-compression-motor encoder sensor count did not change within 10 milliseconds after the master compression motor activated.
P12
300
Overload current was detected in the master removal motor.
P13
203
Cutter HP switch does not go OFF within 100 milliseconds after the cutter motor is activated.
P13
204
Cutter HP switch does not go ON within 300 milliseconds after the cutter motor is activated.
P13
205
Master-positioning sensor is ON when the print drum rotates through the preset angle following master cutting.
P13
221
Both the cutter HP switch and cutter stop position switch are ON at the same time.
P13
222
Cutter HP switch does not go ON within 450 milliseconds after the cutter home positioning operation started.
P13
231
Cutter HP switch does not go OFF within 500 milliseconds after the cutter moved out from the home position.
P13
232
Cutter stop position switch does not go ON within 2 seconds after the cutting operation started.
P13
233
Cutter stop position switch does not go OFF within 500 milliseconds after the cutter activates to move from the stop position to the home position.
P13
234
Cutter HP switch does not go ON within 2 seconds after the cutter home positioning operation started.
P14
114
Incorrect main-unit data.
P14
115
The scanner operation is not completed within the set time.
P14
116
Timeout error for black shading compensation. (RZ3 series only)
P14
117
Timeout error for white shading compensation. (RZ3 series only)
P14
123
Offset adjustment not completed within set time. (RZ3 series only)
P14
124
Gain adjustment not completed within set time. (RZ3 series only)
P14
125
Offset adjustment not completed.
P14
126
Gain adjustment not completed.
P14
135
Malfunction detected during offset adjustment. (RZ3 series only)
P14
136
Malfunction detected during offset adjustment. (RZ3 series only)
P14
137
Malfunction detected during black shading compensation. (RZ3 series only)
P14
138
Malfunction detected during white shading compensation. (RZ3 series only)
P14
170
Even though the read pulse motor stopped according to the sensor detection, the stopping position does not correspond with the programmed position. (GA control error).
P15
4
Communication error with AF-CPU.
P15
110
ABC (auto-base-control) timeout. The original does not move from the ABC scanning position on the AF unit.
P15
111
Operation command was made to the AF unit without 24 volts supplied to the AF unit.
P15
130
Timeout error in receiving reply from the AF unit after command signal was sent from the Riso printer to the AF unit.
P15
131
Riso printer received an undefined command from the AF unit.
P15
132
Riso printer detected communication sequence error from the AF unit.
P15
133
Communication error with AF unit (ACK or NAK error).
P15
134
Riso printer could not send command to the AF unit within the set time.
P15
160
AF unit detection signal went OFF while the AF unit is in operation.
P17
20
Solenoid counter is not connected.
P18
531
Print drum lock sensor is still ON even after 100 milliseconds after the print drum lock solenoid is activated.
P19
207
TPH pressure sensor does not go OFF within 2 seconds after the thermal-pressure motor activates in the decompressing direction, or during home positioning operation.
P19
208
TPH pressure sensor does not go ON within 2 seconds after the thermal-pressure motor activates in the decompressing direction.
P19
216
TPH pressure sensor does not go OFF within 500 millisecond after the thermal-pressure motor activates in the compressing direction.
P19
217
TPH pressure sensor does not go ON within 2 seconds after the thermal-pressure motor activates in the compressing direction.
P20
415
Paper-ejection-wing home sensor does not go OFF within 7,000 milliseconds after the paper ejection wing motor activates in the counterclockwise direction from the home position.
P20
416
Overload current was detected in the paper-ejection motor.
P20
437
Paper-ejection encoder sensor status does not change within 10 milliseconds after the paper-ejection motor is activated.
P24
539
Inking-motor encoder sensor status does not change within 20 milliseconds after the inking-motor is activated.
P25
26
Battery voltage was below 2.3 volts (too low) when the power is turned ON.
P92
570
EEPROM on the print drum PCB was being accessed while the print drum was in releasing action from the machine.
P93
932
No reply from the NET-C network interface card while accessing to the network interface card.
P93
933
No response from NET-C for 90 seconds during NET-C initialization.
P94
225
TPH code does not match with the machine code when the power is turned ON with the master-making unit in operating position or when the master-making unit is inserted in operating position while the power is ON.
P95
59
Machine serial-number information sent from SH-PCB does not match with the machine serial number information in the MCTL PCB.
P96
171
TPH resistance value not input.
P96
172
Scanner adjustment not completed.
P96
433
Paper size width potentiometer test-mode setting is not completed.
P96
569
Either the print drum color information or ink category information is still not input.
P96
613
Print pressure data missing.
P98
2
No reply from Mini-Rosa PCB when the machine power is turned ON even though the Rosa connection signal is ON.
P98
5
Hardware error.
P98
6
FRAM checksum error.
P98
7
Mini Rosa PCB not connected.
P98
38
Machine data on EEPROM does not match with that on the SH-PCB.
P98
39
Improper EEPROM on the SH-PCB.
P98
46
The DIMM capacity does not match.
P98
51
Touch-panel communication error
P98
53
Failure in calling out the saved Memory settings (program, mode, user paper information).
P98
54
Failure in saving the Memory settings (program, mode, user paper information).
P98
55
Machine type code from SH-PCB does not match with the machine information on the H8-PCB.
P98
63
The test-mode memory data stored was outside the adjustment range.
P98
64
An undefined command was sent in communication between SH-PCB and MCTL PCB.
P98
65
Communication error 01 between SH-PCB and MCTL PCB (MCTL PCB side).
P98
67
Communication error 03 between SH-PCB and MCTL PCB (MCTL PCB side).
P98
68
Communication error 04 between SH-PCB and MCTL PCB (MCTL PCB side).
P98
69
Communication error 05 between SH-PCB and MCTL PCB (MCTL PCB side).
P98
70
Communication error 06 between SH-PCB and MCTL PCB (MCTL PCB side).
P98
71
Communication error 07 between SH-PCB and MCTL PCB (MCTL PCB side).
P98
72
Communication error 08 between SH-PCB and MCTL PCB (MCTL PCB side).
P98
73
Communication error 09 between SH-PCB and MCTL PCB (MCTL PCB side).
P98
74
Communication error 10 between SH-PCB and MCTL PCB (SH-PCB side)
P98
75
Communication error 11 between SH-PCB and MCTL PCB (SH-PCB side)
P98
76
Communication error 12 between SH-PCB and MCTL PCB (SH-PCB side)
P98
77
Communication error 13 between SH-PCB and MCTL PCB (SH-PCB side)
P98
78
Communication error 14 between SH-PCB and MCTL PCB (SH-PCB side)
P98
79
Communication error 15 between SH-PCB and MCTL PCB (SH-PCB side)
P98
80
Communication error 16 between SH-PCB and MCTL PCB (SH-PCB side)
P98
81
Communication error 17 between SH-PCB and MCTL PCB (SH-PCB side)
P98
82
Communication error 18 between SH-PCB and MCTL PCB (SH-PCB side)
P98
83
Communication error 19 between SH-PCB and MCTL PCB (SH-PCB side)
P98
84
Communication error 20 between SH-PCB and MCTL PCB (SH-PCB side)
P98
98
Machine serial number information on the SH-PCB EEPROM does not match with that in the FRAM.
P98
119
Image processing PCB trouble.
P98
120
Scanner communication problem. (RZ3 series only)
P98
129
Faulty Scanner GA PCB. (RZ3 series only)
P98
245
Master transfer time-out error during master making (Write pulse motor error).
P98
246
Master transfer time-out error during master making (Load pulse motor error).
P98
614
Vertical print position data missing.
P98
934
Main read/write communication error (detected by read/write side).
P98
935
Main read/write communication error (detected by machine side).
P98
937
Serial number data missing.
P98
938
FRAM version-down.
P98
947
24V-A does not go ON (a possible burnt 24-volt group-A fuse).
P98
948
24V-B does not go ON (a possible burnt 24-volt group-B fuse).
P98
949
24V-A does not go OFF.
P98
950
24V-B does not fo OFF.
P98
952
Checksum error on the ROSA flash-memory.
P98
953
Unsuccessful writing on the ROSA flash-memory.
P99
936
Software error