Ricoh printer error code J001 is a temperature-related error that indicates a problem with the fusing unit in the printer. The fusing unit is responsible for heating the toner particles and bonding them to the paper. Ricoh printer error J001 comes up by inaccurately configured system setups or irregular windows computer system registry entries, a repercussion of malware, or a virus assault. This error can also occur if the temperature sensor in the fusing unit is faulty or damaged. It can also appear due to improper system shutdown as an outcome of a power failure or a few other elements, in case of Paper Out or Failure, to Feed or additionally recognize the when it comes to late error. The late error can be referred to as the paper does not reach the sensing unit at the recommended time.
Causes J001 Error Ricoh Printer
The probable cause of Ricoh printer error j001:
- Paper out
- No feed due to slippage
- Tray 1 set incorrectly
How to fix Ricoh printer error j001?
It is extremely suggested that you need to carry out all the essential actions in a precise way to eliminate the issues.
Method 1: Pass compressed air
- Open the doors as well as blow some compressed air throughout the paper course (where the paper travels up).
- See to it to blow air into the sensing units, for the reason that paper dirt could layer them, triggering incorrect jams.
Method 2: Blow air onto the feed roller
- Every printer has a feed roller that feeds the paper up right into the machine; if you remove the paper tray you could see this roller– it is huge as well as grey and also has gouges throughout it– over where the paper rests towards the front of the printer.
- Blow air into this roller at the same time.
Note: Also make sure the paper is comfortably set in the tray and not bent, torn, or warped.
Method 3: Clean the roller
- If you have either D-ink or a rubber rejuvenator, tidy the roller with a lint-free towel.
Method 4: Scan Computer with Windows Registry Repair Tool
- Download and Install Windows Computer Registry Repair Device from the net. Save the file to your Desktop computer to ensure that we could access the file conveniently.
- After downloading and installing, browse to the file-specific location and also double-click it. It is going to begin the setup procedure. User Account Control is going to trigger if you wish to run the program, click Yes to proceed.
- On the initial launch of the program. it is going to show a welcome display. Leave the checkbox unmarked to enable the repair work device to begin an automated check and also click Install to begin the installation method.
- The software program is going to set up itself on the computer system currently. The tool is going to download and install the require updates, so a Net link needs at this moment.
- The device will immediately begin an initial check of the computer system to help identify the health and wellness of the computer.
- Once the scan is complete, the software program is going to inform you which locations of your computer system are harmed and also if repair work is essential. If it is, click the Begin Repair service switch on the bottom right edge.
- You might need to reboot the computer system to finish the procedure.
For further support or any queries related to Ricoh printer error j001, feel free to dial the Ricoh printer Customer Support Number to avail of online assistance.
- Technical support via live chat
- Certified experts
FAQ’S
Ques 1. Why does my Printer keep saying Printer Error j001?
Ans. The error code “J001” on a printer usually indicates a problem with the printer’s internal temperature sensor. This error occurs when the printer’s temperature exceeds a certain limit or when the printer is unable to detect the correct temperature.
Thanks: 0
Dislikes: 0
-
02-04-2012
#1
Senior Tech
100+ Posts
- Rep Power
- 30
Ricoh MPC 7500 J001 with no signs where to remove paper
Hiya
I have a Ricoh MPC 7500 J001 with no signs where to remove paper.
I have changed the door switches, both sets, updated the firmware, swapped the duplex unit, and whole transport section with the fuser unit in it from another machine.
When I open the door the message does not disapear and door open does not show but the lights on the Printer/Scanner go off and on with the door so it knows the door is opening. Drastically reset the memory and still no joy. Reset the SC and swithched the machine off and on several times and at the plug.
Starts up straight away after a few whirs saying J001, Paper Misfeed, please remove paper from the following points, showing the copier but nothing is high lighted just a picture of the machine with blue lines on it. Disconnected the ADF and Sorter as well.
Never had this. Any help would be FAB as I am lost and knackard after hours of looking.
Tim
-
02-04-2012
#2
Re: Ricoh MPC 7500 J001 with no signs where to remove paper
Hi
Had a simular problem last year and had to remove the power supply..strange, but it helped…try first with a used one….they are not cheap..
-
02-04-2012
#3
Senior Tech
100+ Posts
- Rep Power
- 30
Re: Ricoh MPC 7500 J001 with no signs where to remove paper
Originally Posted by Besserwisser
Hi
Had a simular problem last year and had to remove the power supply..strange, but it helped…try first with a used one….they are not cheap..Hiya Besserwisser. I was thinking that as just took some main board connectors off to see if I have any change but no joy. I will have a go with a spare machine I have and let you know. Thanks for coming back so quickly.
-
02-04-2012
#4
Senior Tech
100+ Posts
- Rep Power
- 30
Re: Ricoh MPC 7500 J001 with no signs where to remove paper
Originally Posted by Timmytronic
Hiya Besserwisser. I was thinking that as just took some main board connectors off to see if I have any change but no joy. I will have a go with a spare machine I have and let you know. Thanks for coming back so quickly.
Hiya
I have swapped the Power supply boards/unit, both, and still no good, always checking to see if the units I took off work on the donor machine and all fine with that. The last resort is now the Main Boards….if anyone has any other ideas that would be gratefully received
Tim
-
02-04-2012
#5
Re: Ricoh MPC 7500 J001 with no signs where to remove paper
Have you tried disconnecting / swapping the feed stations? Could be there’s a sensor out in one of them. Also, take out the LCT and all paper trays before you start it up, may be a trapped wire.
It’s 106 miles to Chicago. We’ve got a full tank of gas, half a pack of cigarettes, it’s dark and we’re wearing sunglasses.
Hit it.
-
02-04-2012
#6
Senior Tech
100+ Posts
- Rep Power
- 30
Re: Ricoh MPC 7500 J001 with no signs where to remove paper
Originally Posted by TonerMunkeh
Have you tried disconnecting / swapping the feed stations? Could be there’s a sensor out in one of them. Also, take out the LCT and all paper trays before you start it up, may be a trapped wire.
Hiya….it does not have an LCT but I will try with all the draws open tomorrow. It’s funny tho as it just does not show anything to say where any paper is. I have taken a picture of the display but not sure how to put it in here with my iphone but will do. I have replaced the paper trays supply board as well. Appreciate your time.
Tim.
-
02-04-2012
#7
-
02-05-2012
#8
Re: Ricoh MPC 7500 J001 with no signs where to remove paper
J001 is a ‘power on’ jam, you may have a flaked out sensor. I would suggest doing an Input Check to determine if any sensors exhibit paper present.
-
02-05-2012
#9
Senior Tech
100+ Posts
- Rep Power
- 30
Re: Ricoh MPC 7500 J001 with no signs where to remove paper
Originally Posted by teebee1234
J001 is a ‘power on’ jam, you may have a flaked out sensor. I would suggest doing an Input Check to determine if any sensors exhibit paper present.
Hi Teebee. Thanks for the advice. I will be putting back the boards today which I swapped to see if that was the issue and get straight on it before I continue with the main board.
I will let you know. Really appreciate it.
Tim.
-
02-05-2012
#10
Senior Tech
100+ Posts
- Rep Power
- 30
Re: Ricoh MPC 7500 J001 with no signs where to remove paper
Originally Posted by Timmytronic
Hi Teebee. Thanks for the advice. I will be putting back the boards today which I swapped to see if that was the issue and get straight on it before I continue with the main board.
I will let you know. Really appreciate it.
Tim.
Hiya. Well found the problem and it was because of a combined help from the messages. I checked the draws and no paper stuck anywhere but as it was a power on jam as mentioned and as I had swapped the transport and fusee section it must of been a draw error…as someone had said. So I just air blasted all the area and sensors and it worked. There is or was alot of paper dust from cheap paper so if it happens again I will do a proper industrial blast and clean.
Hope this has helped anyone. Thanks for all your help. If I can help at all or any MPC Firmware as I have just had the latest which cured a scanner issue please ask.
Tim.
Originally Posted by Besserwisser
Bookmarks
Bookmarks
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
- BB code is On
- Smilies are On
- [IMG] code is On
- [VIDEO] code is On
- HTML code is Off
Forum Rules
If you have a Ricoh printer that is showing the above error, then you can follow the below methods for resolving the Ricoh Printer Error J001.
Method 1- Cleaning the printer
Because a tiny piece of paper can cause this error, therefore, this step aims at cleaning the printer. The steps involved in this method are-
- Switch off the printer by clicking on the power button
- Unplug the power cord of the printer
- Disconnect other cables attached to the printer
- Get a bright flashlight
- Open every tray, lid, paper feed and others and using the flashlight see for any object present.
- If any dust and debris is detected then softly clean all of them
- Connect the cables
- Plug the power cord of the printer
- Switch on the printer by clicking on the power button
- See if the printer is printing or not.
If the above method is unable to solve the issue then you can practice the next method.
Method 2- Blow compressed air
This method aims at passing compressed air with the aim of cleaning dirt. Steps to be taken are-
- Open the doors of the printer and blow compressed air over the paper course.
- Try to blow air into sensing units for cleaning dirt collected over them because of paper dirt.
This method might work if your sensing unit has not been working because of paper dirt.
Method 3- Passing air inside feed roller
This method blows air onto feed roller. Steps to be done under this method are-
- Locate the Feed roller- Feed roller is responsible for feeding paper into the machine and is visible when the paper tray is removed. The first step, therefore, is of locating the feed roller by removing the paper tray. This roller is big and grey with gouges over it. It is on this roller that the paper rest.
- Blowing air- Once when the roller is located the aim is to blow air into the same.
Method 4- Cleaning the roller
In this method, the roller is cleaned as one of the possible reasons for this problem to appear could be the dust inside the roller. If you have D-ink or rubber rejuvenator then lint-free towel could be used for cleaning the roller.
Method 5- Scanning Computer
Within this method, the computer is scanned along the Windows Registry Repair tool. Also, it is a possibility that one might require to boot the computers for completing the scanning activity.
Method 6- Talk to the experts
If you are unable to solve the error even after following all the above steps then you should talk to the experts. You need to dial Ricoh printer customer support number for best assistance.
So practice the methods and print without any error using your high-quality Ricoh printer. There’s your query on how to fix Ricoh printer error j001 answered.
-
dvrussu
Ricoh Aficio MP W2400 (error J001)
Всем доброго !
Имеется данный зверь, привезли из Японии, при перевозке походу уронили, на боковой крышке сколы и трещина.
При запуске показывает замятие бумаг в печке, и выдает ошибку (Paper Misfeed J001).
Если у кого есть сервис-мануал на этот аппарат, буду очень признателен.
Не хочется разбирать его без подготовки.
И еще, поделитесь пожалуйста ссылками, где на него можно запчасти заказать, типа датчиков, флажков, валов и пр… (есть подозрение, что датчик на печке потерял флажок).
Заранее спасибо.
-
dialogserv
Сообщение dialogserv » 18 фев 2010 11:37
Important: Obey these guidelines to avoid problems such as misfeeds, damage to
originals, loss of valuable data and to prevent damage to the machine.
NOTE: This information provides tips and advice about how to best service the
machine.
Может быть это:
• When the machine comes back to normal operation from an energy save mode.
Code Meaning Location Comments
DJ01 Original Set Sensor (A4:81/2, 9″) The original set sensor (A4: 81/2, 9″) is ON.
Вернуться в «Прочие принтеры и копиры»
Кто сейчас на конференции
Сейчас этот форум просматривают: нет зарегистрированных пользователей и 0 гостей
Ricoh Printer Error J001 Quick Fix 2022.Printers have become an important device as it allows you to print, fax, scan and do much more with it. That is why it is important to get a printer that works properly and offers amazing quality.
That is where Ricoh printers come into the picture. These printers are designed to provide you with the best features and results at the same time. They offer a reliable solution for all of the printing needs.
If you are looking for an affordable range of printers then getting a Ricoh printer model is the best solution. However, you need to understand that just like any other device these printers are prone to errors and it is common to experience Ricoh Printer Error J001. If you are facing this error code while using the printer then getting in touch with the technical support team for a solution is the best thing to do.
In this blog, we are also going to cover the steps that you can follow to resolve the error code J001. So, if you are facing any confusion while following the steps then get in touch with the Ricoh printer technicians for help and assistance.
If you are facing this error while using the Ricoh printer then here are the solutions that you need to take. However, if there is any confusion or you need assistance while following the steps then get in touch with the technicians for help and support.
You can follow these steps to fix the error code J001 in the printer immediately:
- The first thing that you need to do is to clean the printer properly. You can turn off the printer by pressing the power button and take out the power cord of the printer. Also, take out the cable connections that are attached to the printer.
- Take out the paper tray and clean the dust or the debris that is preset with a clean cloth or tissue very carefully. Now, connect back the cable connections, plug in the power cord and switch on the printer. Then, check if the printer is resolved or not.
- Pass the compressed air to clean the dust and the dirt. The compressed air will help in removing the dust or the dirt that may be blocking and causing an issue.
- Pass the air inside the feed roller. Make sure to clean the roller with a clean paper or cloth.
- Use the repair tool in the Windows for scanning. Then reboot the computer and the printer to resolve the error code.
In this blog, we have covered in detail the steps that you need to take to fix the Ricoh Printer Error J001. However, if you are having any issue while resolving the error code by following these steps or if the problem persists then get help from the technical support team. The experts will guide and assist you in resolving the issue with the printer. Contact the Ricoh printer technicians for help and support.
Is your Printer is Offline? Visit Now Printer Offline Support or Call Now +1 (828) 490-7310.