Rexroth f8022 ошибка

The Indradrive is a generational jump for Rexroth Electric Drives and Controls, and there are distinct differences between Indradrive and Indramat. One of the differences is the much greater number of error messages available to Indradrive, and the corresponding higher granularity of initial troubleshooting available.

While the older series drives had a 4 digit (or less) alphanumeric error code that would show up on the H1 display, the Indradrive series has a 5 digit display. Some of the old favorites are still here (bb still means Drive Healthy), but there are a whole wealth of new error codes available.

New codes

F9xxx – Fatal System Errors

Watchdog triggers, Processor crash, firmware corruption are all in F9xxx. If you get an F9xxx, it’s probably about to be a bad day

F8xxx – Fatal Errors

Errors that preclude continued operation of the drive, but which might not signify a major hardware fault. Our old friend F822 falls into this category, but is now sporting a new 0 to move up to 5 digits (F8022 now).

F7xxx – Safety Technology Errors

These errors have to do with the new Safety Tech available on the drives. In systems that have been operating for a long period (not in startup), these may point to a problem in the wiring, not in the drive. Care should be taken in troubleshooting.

F6xxx – Travel Range Errors

Trying to run off the end of the rails. These errors have to do with either hitting a physical End of Travel limit switch or ordering a move that goes outside of the parameterized range of travel. Typically these are an easy fix, although there can be some wrinkles.

F4xxx – Interface Errors

A better title for these errors would be Control Interface Errors. With one exception, these errors all have to do with external control signals not meeting the requirements of the drives (double MDT or MST failures, Communication buss failures). The exception is not really a failure, but a state, F4034, which the experienced user will note is the old Emergency Stop (F434) with an additional 0.

F3xxx – Non-Fatal Safety Technology Errors

Again, not the best title. These errors will stop the drives, but allow you a different reaction to be set up than the F7xxx. Several of these errors will require replacement of the control section, but further reference to individual errors is required.

F2xxx – Non Fatal Errors

These are all of the errors that don’t directly have to do with the drive operation. Motor overtemp, Drive overtemp, problems with accel/decal and most other general problems fall into this group.

Having the proper manual is always the first step of good troubleshooting. You can use the “Manual Request” button to get one emailed to you. You can also call for assistance. We will do everything we can to get you up and running again without delay.

Rexroth error messages are made up of a diagnostic code and a diagnostic text. For error F2028, “F2” and “28” alternate on the H1 display. In the diagnostic message, it shows as F2028. F2028 is one of the “excessive” — error codes that tell you there’s too much of something. In this case, it’s too much deviation.

There are lots of error codes for various conditions and various components.

One group of error codes includes the word “excessive.” Sometimes too much of a good thing is just too much.

Excessives error codes

• F2027 Excessive oscillation in DC bus

The DC bus voltage fluctuates too much. The oscillation might not be visible in the machine, so be sure to check the command torque. Check the settings on the velocity control loop and the position control loop.

• F2028 Excessive deviation

When the actual position exceeds the expected parameters, this error is generated. This can be caused by errors in the parameters, if the axis is blocked, or when the power supply was turned off while the controller enable signal was applied. Check both the mechanical system to correct axis jamming, and the parameters to make sure they’re correct.

• F2036 Excessive position feedback difference

This error code means that the difference between actual position value 1 and position value 2 is greater than the monitoring window.

• F2037 Excessive position command difference

F2037 is the error shown when the position difference between two successive position command values is the same as the value in the  bipolar velocity limit value — or larger.

Can we help?

Error codes can be caused by too much, too little, or just the wrong things. But any error code is more error codes than you really want to deal with.

Call us at 479-422-0390 for any Rexroth electric motion control issues. We specialize in Rexroth electric industrial motion control. We offer phone support, field support, and factory repair and reman. We also maintain the nation’s largest inventory of Rexroth electric drive and control components.