If the VPN Server incoming connections doesn’t work, because the Remote Access protocols rasgreeng.dll & IKEv2 failed to initialize, continue reading below to fix the problem.
Problem in details. After setting up Windows 10 as a VPN server, clients cannot connect to the VPN server because after entering the credentials, the connection is dropped without any obvious reason. When this happens, the following two errors are logged on the VPN server.
- Remote Access Connection Manager failed to start because the Protocol engine [rasgreeng.dll] failed to initialize. The specified module could not be found. (Event ID: 20063)
-
Remote Access Connection Manager failed to start because the Protocol engine [IKEv2] failed to initialize. The request is not supported.(Event ID: 20063)
How to FIX: Remote Access Connection Manager failed to start: rasgreeng.dll & IKEv2 failed to initialize on Windows 10 (Event ID 20063).
To fix the Event ID 20063 in Remote Access Connection Manager, perform the below steps:
1. On the VPN Server, open the Windows Services control panel: To do that:
-
- Press Windows
+ R keys to open the run command box. - In the Search box, type: services.msc & click OK.
- Press Windows
+ R keys to open the run command box.
2. In Services, double click to open the Remote Access Auto Connection Manager service.
3. Set the Startup type to Automatic and click Apply.
4. Then Start the service and click OK or restart the PC.
5. Try to connect to the VPN server from the clients. The problem should be resolved.*
* Note: If the problem is not fixed, apply the following steps.
1. Ensure that the following services on the VPN server are up and running:
-
DCOM Server Process Launcher (DcomLaunch)
-
Plug and Play (PlugPlay)
-
Remote Access Connection Manager (RasMan)
-
Remote Procedure Call (RPC) (RpcSs)
-
RPC Endpoint Mapper (RpcEptMapper)
-
Secure Socket Tunneling Protocol Service (SstpSvc)
-
Telephony (TapiSrv)
2. Repair the Windows system files, by running the following commands (in order) in Admin Command Prompt and then reboot your PC:
-
DISM /Online /Cleanup-Image /StartComponentCleanup
- DISM.exe /Online /Cleanup-image /Restorehealth
- sfc /scannow
That’s all folks! Did it work for you?
Please leave a comment in the comment section below or even better: like and share this blog post in the social networks to help spread the word about this solution.
If this article was useful for you, please consider supporting us by making a donation. Even $1 can a make a huge difference for us.
Unable to start Routing and Remote Access Server (RRAS) (Event IDs: 7023, 20070, 20151, 20063) after uninstalling Symantec Antivirus/Symantec Endpoint Protection
calendar_today
Updated On:
Products
Endpoint Protection
Issue/Introduction
Why is this error produced after uninstalling Symantec Antivirus/Endpoint? «Unable to start RRAS (Event IDs: 7023, 20070, 20151, 20063)»
Symptoms
First Error:
Source: RemoteAccess
Event ID: 20070
Error: Point to Point Protocol engine was unable to load the C:\Program Files\Symantec\Symantec Endpoint Protection\SymRasMan.dll module. The specified module could not be found.
Second Error:
Source: RemoteAccess
Event ID: 20151
Error: The Control Protocol EAP in the Point to Point Protocol module C:\WINDOWS\System32\rasppp.dll returned an error while initializing. The specified module could not be found.
Third Error:
Source: Rasman
Event ID: 20063
Error: Remote Access Connection Manager failed to start because the Point to Point Protocol failed to initialize. The specified module could not be found.
Fourth Error:
Source: Service Control Manager
Event ID: 7023
Error: The Remote Access Connection Manager service terminated with the following error: The specified module could not be found.
Fifth Error:
If tried to restart the service from RRAS mmc, it gives the following Error: «Routing and Remote Access cannot be started because of the following error.» Please see event log for more information: The service has returned a service-specific error code. (8007042a)
Cause
The default location of the file SymRasMan.dll is %SystemRoot%\System32\rastls.dll. On installing Symantec Antivirus or Symantec Endpoint Protection the default location is then changed and edited in the registry to C:\Program Files\SAV\SymRasMan.dll. After uninstallation this location is not reversed for Windows Server 2003 SP2 because it does create a backup of the key during the change/installation unlike Windows Small Business Server 2003
In SEP 12.1 it can result from a known issue described in TECH164677 — Clients show «No Symantec protection technologies are installed» after migrating the SEPM from 11.x to 12.1
Resolution
To resolve this issue follow the steps below:
- Click Start
- Click Run
- Type regedit
- Navigate to:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\RasMan\PPP\EAP\13 - Select the folder 13
- Change the value for keys: “ConfigUiPath”, “IdentityPath”, “InteractiveUIPath” and “Path” to:
%SystemRoot%\System32\rastls.dll - Navigate to:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\RasMan\PPP\EAP\25 - Select the folder 25
- Change the value for keys: “ConfigUiPath”, “IdentityPath”, “InteractiveUIPath” and “Path” to:
%SystemRoot%\System32\rastls.dll - Restart the computer (recommended not required)
- Start the RRAS service
Feedback
thumb_up
Yes
thumb_down
No
If you see the rasman id 20063 error on your computer, check out these troubleshooting tips.
Approved: Fortect
Speed up your computer’s performance now with this simple download.
This issue requires space if both of the following conditions are encountered: You are upgrading a computer that is running Windows 2000 Service Pack 3 (SP3) to Windows 2000 Service Pack 4 (SP4). You have not configured a routing and then dial-up or dial-up connection on a computer that is performing a one-time upgrade to Windows 2000 SP4.
Keep track of an endless number of servers
Log events filter
Email to create web reports
Direct access to articles from Microsoft
Custom keywords for major search engines
Access to content coverage cost
Source
Microsoft ISA H.323 Firewall Filter
Description
An H.323 filter cannot be configured to register with an H.323 gatekeeper in order to detect the gatekeeper multicast discovery in use. Incoming H.323 calls will never succeed unless the filter is accredited by the gatekeeper. To set up a block to use opspecific gatekeeper, change some of the H.323 filter call control properties and enter the H.323 gatekeeper to register.
Description
The Remote Access Connection Manager was unable to start the specified point-to-point protocol, so it is initialized.
Description
The Remote Access Connection Manager error, so you start it because the point-to-point protocol could not be initialized. Currently, there is never a Connection Server to handle a connection request.
Splunk Windows Event Log Analysis Application
Build a great reporting interface with Splunk, especially for security and event management (SIEM) personnel who often associate collected Windows events with www.eventid.net.
More …
Splunk Application for Cisco ASA Log Analyzer
Approved: Fortect
Fortect is the world’s most popular and effective PC repair tool. It is trusted by millions of people to keep their systems running fast, smooth, and error-free. With its simple user interface and powerful scanning engine, Fortect quickly finds and fixes a broad range of Windows problems — from system instability and security issues to memory management and performance bottlenecks.
Get dramatically improved visibility of the Cisco ASA Firewall logs with a free app.Firegen Application for Cisco ASA Splunk. Use dashboards designed as a threat intelligence optimization process.
More … No Limits
Keep track of the number of servers
Log Event Filter
Create reports by email and on the web
Direct access to articles from Microsoft
Keywords suitable for major search engines
Access to quality content
The H.323 filter is not configured to register an H.323 gatekeeper trying to find a new one using gatekeeper multicast discovery. Incoming H.323 voice messages will not be successful until the filter is permanently registered by the gatekeeper. To tilt the filter to use a single gatekeeper, modify the call control components of the H.323 filter and enter the H.323 gatekeeper for which you want to register.
RAS connection failed during manager focus because point-to-point protocol initialization completed.
С Remote Access Connection An error occurred while starting the dispatcher because the point-to-point protocol could not be initialized. Of course, there are currently no platform connection servers available to request a connection.
Splunk Windows Event Log Analysis Application
Build a great reporting interface with Splunk, the leader in security information and event management (SIEM), and link collected Windows events to www.eventid.net.
Cisco ASA Log Analyzer Splunk Application
Get better visibility into the Cisco ASA Firewall logs with any free Cisco ASA Splunk Firegen app. Use dashboards designed to streamline your threat intelligence process.
Unable To Start Routing And Remote Access Server (RRAS) (event ID: 7023, 20070, 20151, 20063) After Uninstalling Symantec Antivirus / Symantec Endpoint Protection
Updated:
Products
Endpoint Security
Problem / Introduction
Why does this error usually appear after uninstalling Symantec Antivirus / Endpoint? “Unable to start RRAS (Event ID: 7023, 20070, 20151, 20063)”
Source: Remote Access
Event ID: 20070
Error: The Point-to-Point Protocol Subsystem was unable to load drive C: Program Files Symantec Symantec Endpoint Protection SymRasMan.dll. The specified module is not observed. Error:
Source:
second remote access
Event ID: 20151
Error: EAP control protocol in point-to-point protocol module C: WINDOWS System32 rasppp.dll also returned an error during initialization. The specified module could not be recognizednan.
Third error:
Source: Rasman
Event ID: Remote 20063
error: The Access Connection Manager could not be started because the point-to-point protocol could not be initialized. The specified module could not be found.
Fourth error:
Source: Service Control Manager
Event ID: 7023
Error: The Remote Access Connection Manager service was interrupted due to the following error: The specified module could not be found permanently.
Fifth error:
When you try to restart your computer using the mmc RRAS service, you receive the following error: “Remote Routing and Access could not be started due to a previous error.” For more information about the log, see Event: Service returned a large error code specific to the service. (8007042a)
Reason
In fact,% SystemRoot% System32 rastls.dll is the cause of the SymRasMan.dll file failure. When you install Symantec Antivirus or Symantec Endpoint Protection, the default path is modified and edited.I’m in the registry at C: Program Files SAV SymRasMan.dll. After uninstallation, this location does not really change to the opposite for Windows Server 2003 SP2, because unlike Windows Small Business Server 2003, the key is backed up during edit / installation
On September 1st, this idea may be the result of a known issue in TECH164677: After upgrading from sepm 11.x to 12.1, customers report “Symantec security technology not installed”
Resolution
- Click Start.
- Click Run.
- Enter regedit.
- Go to:
HKEY_LOCAL_MACHINE SYSTEM CurrentControlSet Services RasMan PPP EAP 13 - Select folder 13
- Change the key value: “ConfigUiPath”, “IdentityPath”, “InteractiveUIPath” and “Path” to:
% SystemRoot% System32 rastls.dll - Go to:
HKEY_LOCAL_MACHINE SYSTEM CurrentControlSet Services RasMan PPP EAP 25 - Select file 25
- Change the value to contain the keys: “ConfigUiPath”, “InteractiveUIPath”, “identitypath” and “Path” to:
% SystemRoot% System32 rastls.dll - R
Speed up your computer’s performance now with this simple download.
Unable to start Routing and Remote Access Server (RRAS) (Event IDs: 7023, 20070, 20151, 20063) after uninstalling Symantec Antivirus/Symantec Endpoint Protection
calendar_today
Updated On:
Products
Endpoint Protection
Issue/Introduction
Why is this error produced after uninstalling Symantec Antivirus/Endpoint? «Unable to start RRAS (Event IDs: 7023, 20070, 20151, 20063)»
Symptoms
First Error:
Source: RemoteAccess
Event ID: 20070
Error: Point to Point Protocol engine was unable to load the C:Program FilesSymantecSymantec Endpoint ProtectionSymRasMan.dll module. The specified module could not be found.
Second Error:
Source: RemoteAccess
Event ID: 20151
Error: The Control Protocol EAP in the Point to Point Protocol module C:WINDOWSSystem32rasppp.dll returned an error while initializing. The specified module could not be found.
Third Error:
Source: Rasman
Event ID: 20063
Error: Remote Access Connection Manager failed to start because the Point to Point Protocol failed to initialize. The specified module could not be found.
Fourth Error:
Source: Service Control Manager
Event ID: 7023
Error: The Remote Access Connection Manager service terminated with the following error: The specified module could not be found.
Fifth Error:
If tried to restart the service from RRAS mmc, it gives the following Error: «Routing and Remote Access cannot be started because of the following error.» Please see event log for more information: The service has returned a service-specific error code. (8007042a)
Cause
The default location of the file SymRasMan.dll is %SystemRoot%System32rastls.dll. On installing Symantec Antivirus or Symantec Endpoint Protection the default location is then changed and edited in the registry to C:Program FilesSAVSymRasMan.dll. After uninstallation this location is not reversed for Windows Server 2003 SP2 because it does create a backup of the key during the change/installation unlike Windows Small Business Server 2003
In SEP 12.1 it can result from a known issue described in TECH164677 — Clients show «No Symantec protection technologies are installed» after migrating the SEPM from 11.x to 12.1
Resolution
To resolve this issue follow the steps below:
- Click Start
- Click Run
- Type regedit
- Navigate to:
HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesRasManPPPEAP13 - Select the folder 13
- Change the value for keys: “ConfigUiPath”, “IdentityPath”, “InteractiveUIPath” and “Path” to:
%SystemRoot%System32rastls.dll - Navigate to:
HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesRasManPPPEAP25 - Select the folder 25
- Change the value for keys: “ConfigUiPath”, “IdentityPath”, “InteractiveUIPath” and “Path” to:
%SystemRoot%System32rastls.dll - Restart the computer (recommended not required)
- Start the RRAS service
Feedback
thumb_up
Yes
thumb_down
No
If the VPN Server incoming connections doesn’t work, because the Remote Access protocols rasgreeng.dll & IKEv2 failed to initialize, continue reading below to fix the problem.
Problem in details. After setting up Windows 10 as a VPN server, clients cannot connect to the VPN server because after entering the credentials, the connection is dropped without any obvious reason. When this happens, the following two errors are logged on the VPN server.
- Remote Access Connection Manager failed to start because the Protocol engine [rasgreeng.dll] failed to initialize. The specified module could not be found. (Event ID: 20063)
-
Remote Access Connection Manager failed to start because the Protocol engine [IKEv2] failed to initialize. The request is not supported.(Event ID: 20063)
How to FIX: Remote Access Connection Manager failed to start: rasgreeng.dll & IKEv2 failed to initialize on Windows 10 (Event ID 20063).
To fix the Event ID 20063 in Remote Access Connection Manager, perform the below steps:
1. On the VPN Server, open the Windows Services control panel: To do that:
-
- Press Windows + R keys to open the run command box.
- In the Search box, type: services.msc & click OK.
- Press Windows
2. In Services, double click to open the Remote Access Auto Connection Manager service.
3. Set the Startup type to Automatic and click Apply.
4. Then Start the service and click OK or restart the PC.
5. Try to connect to the VPN server from the clients. The problem should be resolved.*
* Note: If the problem is not fixed, apply the following steps.
1. Ensure that the following services on the VPN server are up and running:
-
DCOM Server Process Launcher (DcomLaunch)
-
Plug and Play (PlugPlay)
-
Remote Access Connection Manager (RasMan)
-
Remote Procedure Call (RPC) (RpcSs)
-
RPC Endpoint Mapper (RpcEptMapper)
-
Secure Socket Tunneling Protocol Service (SstpSvc)
-
Telephony (TapiSrv)
2. Repair the Windows system files, by running the following commands (in order) in Admin Command Prompt and then reboot your PC:
-
DISM /Online /Cleanup-Image /StartComponentCleanup
- DISM.exe /Online /Cleanup-image /Restorehealth
- sfc /scannow
That’s all folks! Did it work for you?
Please leave a comment in the comment section below or even better: like and share this blog post in the social networks to help spread the word about this solution.
If this article was useful for you, please consider supporting us by making a donation. Even $1 can a make a huge difference for us.
Здравствуйте перестал работать VPN в журнале следующие ошибки:
Код:20063 Источник: RemoteAccess
Произошел сбой при запуске диспетчера подключений удаленного доступа, так как не удалось инициализировать модуль протоколов [IKEv2]. The request is not supported.
Код:24 Источник:WMI
Поставщик событий попытался зарегистрировать запрос «select * from RemoteAccessError», целевой класс «RemoteAccessError» которого не существует в пространстве имен //./ROOT/Microsoft/Windows/RemoteAccess/Server. Запрос будет
пропущен
Код:24 Источник:WMI
Поставщик событий RAServerPSProvider попытался зарегистрировать запрос «select * from RemoteAccessError», целевой класс «RemoteAccessError» которого не существует в пространстве имен //./ROOT/Microsoft/Windows/RemoteAccess/Server.
Запрос будет пропущен
Код:18 Источник:RasSstp
Службе SSTP не удалось прочитать из реестра хеш сертификата SHA256, либо эти данные недопустимы. Допустимый хеш сертификата SHA256 должен иметь тип REG_BINARY и длину в 32 байта. Возможно, SSTP не удалось извлечь значение из реестра
из-за другой системной ошибки. Подробное сообщение об ошибке приведено ниже. Подключения SSTP не будут приняты на этом сервере. Исправьте ошибку и повторите попытку.
The system cannot find the file specified.
Event ID: 20063 Description: Remote Access Connection Manager failed to start because the Point to Point Protocol failed to initialize. %1 is not a valid Win32 application..
Full
Answer
Why is my event viewer displaying event ID 20063 error?
Event viewer is displaying Event ID: 20063 error «Remote Access Connection Manager failed to start because the Protocol engine [rasgreeng.dll] failed to initialize. The specified module could not be found.»
What is the remote access connection manager service?
The service is a dependency service to Remote Access Connection Manager and has been «disabled» on all the Windows 10 systems after the latest update. If this service is «started», the following errors are displayed in Event Viewer: Remote Access Connection Manager failed to start because the Protocol engine [IKEv2] failed to initialize.
What is the default run status of the routing and remote access?
What is the default run status of the «Routing and Remote Access» service? The service is a dependency service to Remote Access Connection Manager and has been «disabled» on all the Windows 10 systems after the latest update. If this service is «started», the following errors are displayed in Event Viewer:
How to run services.msc?
1. Press Windows + R for Run and then type Services.msc and then Enter.
How to check if a service has been stopped?
Follow the below methods and check if it helps, Method 1: 1. Press Windows + R for Run and then type Services.msc and then Enter . 2. Select Remote access connection manager and then right click and select Start if the service has been stopped. 3.
Why is Remote Access Connection Manager not starting?
Remote Access Connection Manager failed to start because it could not load one or more communication DLLs. Ensure that your communication hardware is installed and then restart the Remote Access Connection Manager service. If the problem persists, contact the system administrator. There was an unknown error.
Popular Posts:
If you see the rasman id 20063 error on your computer, check out these troubleshooting tips.
Approved: ASR Pro
Speed up your computer’s performance now with this simple download.
This issue requires space if both of the following conditions are encountered: You are upgrading a computer that is running Windows 2000 Service Pack 3 (SP3) to Windows 2000 Service Pack 4 (SP4). You have not configured a routing and then dial-up or dial-up connection on a computer that is performing a one-time upgrade to Windows 2000 SP4.
Keep track of an endless number of servers
Log events filter
Email to create web reports
Direct access to articles from Microsoft
Custom keywords for major search engines
Access to content coverage cost
Source
Microsoft ISA H.323 Firewall Filter
Description
An H.323 filter cannot be configured to register with an H.323 gatekeeper in order to detect the gatekeeper multicast discovery in use. Incoming H.323 calls will never succeed unless the filter is accredited by the gatekeeper. To set up a block to use opspecific gatekeeper, change some of the H.323 filter call control properties and enter the H.323 gatekeeper to register.
Description
The Remote Access Connection Manager was unable to start the specified point-to-point protocol, so it is initialized.
Description
The Remote Access Connection Manager error, so you start it because the point-to-point protocol could not be initialized. Currently, there is never a Connection Server to handle a connection request.
Splunk Windows Event Log Analysis Application
Build a great reporting interface with Splunk, especially for security and event management (SIEM) personnel who often associate collected Windows events with www.eventid.net.
More …
Splunk Application for Cisco ASA Log Analyzer
Approved: ASR Pro
ASR Pro is the world’s most popular and effective PC repair tool. It is trusted by millions of people to keep their systems running fast, smooth, and error-free. With its simple user interface and powerful scanning engine, ASR Pro quickly finds and fixes a broad range of Windows problems — from system instability and security issues to memory management and performance bottlenecks.
Get dramatically improved visibility of the Cisco ASA Firewall logs with a free app.Firegen Application for Cisco ASA Splunk. Use dashboards designed as a threat intelligence optimization process.
More … No Limits
Keep track of the number of servers
Log Event Filter
Create reports by email and on the web
Direct access to articles from Microsoft
Keywords suitable for major search engines
Access to quality content
The H.323 filter is not configured to register an H.323 gatekeeper trying to find a new one using gatekeeper multicast discovery. Incoming H.323 voice messages will not be successful until the filter is permanently registered by the gatekeeper. To tilt the filter to use a single gatekeeper, modify the call control components of the H.323 filter and enter the H.323 gatekeeper for which you want to register.
RAS connection failed during manager focus because point-to-point protocol initialization completed.
С Remote Access Connection An error occurred while starting the dispatcher because the point-to-point protocol could not be initialized. Of course, there are currently no platform connection servers available to request a connection.
Splunk Windows Event Log Analysis Application
Build a great reporting interface with Splunk, the leader in security information and event management (SIEM), and link collected Windows events to www.eventid.net.
Cisco ASA Log Analyzer Splunk Application
Get better visibility into the Cisco ASA Firewall logs with any free Cisco ASA Splunk Firegen app. Use dashboards designed to streamline your threat intelligence process.
Unable To Start Routing And Remote Access Server (RRAS) (event ID: 7023, 20070, 20151, 20063) After Uninstalling Symantec Antivirus / Symantec Endpoint Protection
Updated:
Products
Endpoint Security
Problem / Introduction
Why does this error usually appear after uninstalling Symantec Antivirus / Endpoint? “Unable to start RRAS (Event ID: 7023, 20070, 20151, 20063)”
Source: Remote Access
Event ID: 20070
Error: The Point-to-Point Protocol Subsystem was unable to load drive C: Program Files Symantec Symantec Endpoint Protection SymRasMan.dll. The specified module is not observed. Error:
Source:
second remote access
Event ID: 20151
Error: EAP control protocol in point-to-point protocol module C: WINDOWS System32 rasppp.dll also returned an error during initialization. The specified module could not be recognizednan.
Third error:
Source: Rasman
Event ID: Remote 20063
error: The Access Connection Manager could not be started because the point-to-point protocol could not be initialized. The specified module could not be found.
Fourth error:
Source: Service Control Manager
Event ID: 7023
Error: The Remote Access Connection Manager service was interrupted due to the following error: The specified module could not be found permanently.
Fifth error:
When you try to restart your computer using the mmc RRAS service, you receive the following error: “Remote Routing and Access could not be started due to a previous error.” For more information about the log, see Event: Service returned a large error code specific to the service. (8007042a)
Reason
In fact,% SystemRoot% System32 rastls.dll is the cause of the SymRasMan.dll file failure. When you install Symantec Antivirus or Symantec Endpoint Protection, the default path is modified and edited.I’m in the registry at C: Program Files SAV SymRasMan.dll. After uninstallation, this location does not really change to the opposite for Windows Server 2003 SP2, because unlike Windows Small Business Server 2003, the key is backed up during edit / installation
On September 1st, this idea may be the result of a known issue in TECH164677: After upgrading from sepm 11.x to 12.1, customers report “Symantec security technology not installed”
Resolution
- Click Start.
- Click Run.
- Enter regedit.
- Go to:
HKEY_LOCAL_MACHINE SYSTEM CurrentControlSet Services RasMan PPP EAP 13 - Select folder 13
- Change the key value: “ConfigUiPath”, “IdentityPath”, “InteractiveUIPath” and “Path” to:
% SystemRoot% System32 rastls.dll - Go to:
HKEY_LOCAL_MACHINE SYSTEM CurrentControlSet Services RasMan PPP EAP 25 - Select file 25
- Change the value to contain the keys: “ConfigUiPath”, “InteractiveUIPath”, “identitypath” and “Path” to:
% SystemRoot% System32 rastls.dll - R
Speed up your computer’s performance now with this simple download.
Today I experienced another issue with Windows 10 upgrade (to the Fall Creators Update) and the VPN server functionality. After quick research, it turned out that errors are written to the event log after each client’s attempt to connect:
- Remote Access Connection Manager failed to start because the Protocol engine [rasgreeng.dll] failed to initialize. The specified module could not be found.
- Remote Access Connection Manager failed to start because the Protocol engine [IKEv2] failed to initialize. The request is not supported.
Looking for mentioned .dll led to dead end — no such .dll exists on any my Windows 10 machines. However, then I checked the services and noticed that one of them related to remote access — Remote Access Auto Connection Manager (RasAuto) is not running. So I changed the startup type option from Manual to Automatic, restarted PC, and everything worked like a charm.
I am experiencing a problem with Windows VPN on my Lenovo Ideapad, running Windows 10 1909. The problem makes a lot of network-related settings pages work very slowly. For example, it takes a long time for the list of WiFi networks to load when I click on the icon in the taskbar (and it leaves out the VPN networks). The network pages in the Settings app also work very slowly. Finally, when I try to connect to a VPN (after getting to the page), it gets stuck saying “Connecting”. The VPN I use is L2TP/IPSec with PSK, using the built-in VPN provider.
I found the following errors in Event Viewer (System):
- RasMan – 20027 – Remote Access Connection Manager failed to start because NDISWAN could not be opened.
- RasMan – 20063 – Remote Access Connection Manager failed to start because the Protocol engine [C:WINDOWSsystem32vpnike.dll] failed to initialize. The system cannot find the device specified.
- Service Control Manager – 7023 – The Remote Access Connection Manager service terminated with the following error:
The system cannot find the device specified.
These errors occur in this order whenever I try to use those network settings pages or connect to a VPN.
My problem is just about identical to the one discussed on this SpiceWorks thread. However, I have tried everything there and it did not work. I’m honestly not sure how removing vpnike.dll fixed the problem for the person on SpiceWorks, considering that there wouldn’t be anything to handle IKE…
Things I have tried:
sfc /scannow- Registering vpnike.dll using
regsvr32 netsh int ip reset c:resetlog.txtand rebootingdism /Online /Cleanup-Image /ScanHealth(No component store corruption detected)- Comparing vpnike.dll and ndiswan.sys to files on other computers – I took a SHA256 hash and it matched other Windows 10 1909 computers.
- Renaming vpnike.dll
- Renaming vpnike.dll and then running
sfc /scannow– This allows the settings pages to work, but when I try to connect to a VPN, it says “A device of that type does not exist.” No error in the event log. - Restarting, renaming vpnike.dll, running
sfc /scannow, and renaming vpnike.dll again… (Still says “A device type was specified that does not exist.”) - Renaming ndiswan.sys
- Renaming ndiswan.sys and running
sfc /scannow
Unable to start Routing and Remote Access Server (RRAS) (Event IDs: 7023, 20070, 20151, 20063) after uninstalling Symantec Antivirus/Symantec Endpoint Protection
calendar_today
Updated On:
Products
Endpoint Protection
Issue/Introduction
Why is this error produced after uninstalling Symantec Antivirus/Endpoint? «Unable to start RRAS (Event IDs: 7023, 20070, 20151, 20063)»
Symptoms
First Error:
Source: RemoteAccess
Event ID: 20070
Error: Point to Point Protocol engine was unable to load the C:Program FilesSymantecSymantec Endpoint ProtectionSymRasMan.dll module. The specified module could not be found.
Second Error:
Source: RemoteAccess
Event ID: 20151
Error: The Control Protocol EAP in the Point to Point Protocol module C:WINDOWSSystem32rasppp.dll returned an error while initializing. The specified module could not be found.
Third Error:
Source: Rasman
Event ID: 20063
Error: Remote Access Connection Manager failed to start because the Point to Point Protocol failed to initialize. The specified module could not be found.
Fourth Error:
Source: Service Control Manager
Event ID: 7023
Error: The Remote Access Connection Manager service terminated with the following error: The specified module could not be found.
Fifth Error:
If tried to restart the service from RRAS mmc, it gives the following Error: «Routing and Remote Access cannot be started because of the following error.» Please see event log for more information: The service has returned a service-specific error code. (8007042a)
Cause
The default location of the file SymRasMan.dll is %SystemRoot%System32rastls.dll. On installing Symantec Antivirus or Symantec Endpoint Protection the default location is then changed and edited in the registry to C:Program FilesSAVSymRasMan.dll. After uninstallation this location is not reversed for Windows Server 2003 SP2 because it does create a backup of the key during the change/installation unlike Windows Small Business Server 2003
In SEP 12.1 it can result from a known issue described in TECH164677 — Clients show «No Symantec protection technologies are installed» after migrating the SEPM from 11.x to 12.1
Resolution
To resolve this issue follow the steps below:
- Click Start
- Click Run
- Type regedit
- Navigate to:
HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesRasManPPPEAP13 - Select the folder 13
- Change the value for keys: “ConfigUiPath”, “IdentityPath”, “InteractiveUIPath” and “Path” to:
%SystemRoot%System32rastls.dll - Navigate to:
HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesRasManPPPEAP25 - Select the folder 25
- Change the value for keys: “ConfigUiPath”, “IdentityPath”, “InteractiveUIPath” and “Path” to:
%SystemRoot%System32rastls.dll - Restart the computer (recommended not required)
- Start the RRAS service
Feedback
thumb_up
Yes
thumb_down
No
If the VPN Server incoming connections doesn’t work, because the Remote Access protocols rasgreeng.dll & IKEv2 failed to initialize, continue reading below to fix the problem.
Problem in details. After setting up Windows 10 as a VPN server, clients cannot connect to the VPN server because after entering the credentials, the connection is dropped without any obvious reason. When this happens, the following two errors are logged on the VPN server.
- Remote Access Connection Manager failed to start because the Protocol engine [rasgreeng.dll] failed to initialize. The specified module could not be found. (Event ID: 20063)
-
Remote Access Connection Manager failed to start because the Protocol engine [IKEv2] failed to initialize. The request is not supported.(Event ID: 20063)
How to FIX: Remote Access Connection Manager failed to start: rasgreeng.dll & IKEv2 failed to initialize on Windows 10 (Event ID 20063).
To fix the Event ID 20063 in Remote Access Connection Manager, perform the below steps:
1. On the VPN Server, open the Windows Services control panel: To do that:
-
- Press Windows + R keys to open the run command box.
- In the Search box, type: services.msc & click OK.
- Press Windows
2. In Services, double click to open the Remote Access Auto Connection Manager service.
3. Set the Startup type to Automatic and click Apply.
4. Then Start the service and click OK or restart the PC.
5. Try to connect to the VPN server from the clients. The problem should be resolved.*
* Note: If the problem is not fixed, apply the following steps.
1. Ensure that the following services on the VPN server are up and running:
-
DCOM Server Process Launcher (DcomLaunch)
-
Plug and Play (PlugPlay)
-
Remote Access Connection Manager (RasMan)
-
Remote Procedure Call (RPC) (RpcSs)
-
RPC Endpoint Mapper (RpcEptMapper)
-
Secure Socket Tunneling Protocol Service (SstpSvc)
-
Telephony (TapiSrv)
2. Repair the Windows system files, by running the following commands (in order) in Admin Command Prompt and then reboot your PC:
-
DISM /Online /Cleanup-Image /StartComponentCleanup
- DISM.exe /Online /Cleanup-image /Restorehealth
- sfc /scannow
That’s all folks! Did it work for you?
Please leave a comment in the comment section below or even better: like and share this blog post in the social networks to help spread the word about this solution.
If this article was useful for you, please consider supporting us by making a donation. Even $1 can a make a huge difference for us.
Unable to start Routing and Remote Access Server (RRAS) (Event IDs: 7023, 20070, 20151, 20063) after uninstalling Symantec Antivirus/Symantec Endpoint Protection
calendar_today
Updated On:
Products
Endpoint Protection
Issue/Introduction
Why is this error produced after uninstalling Symantec Antivirus/Endpoint? «Unable to start RRAS (Event IDs: 7023, 20070, 20151, 20063)»
Symptoms
First Error:
Source: RemoteAccess
Event ID: 20070
Error: Point to Point Protocol engine was unable to load the C:Program FilesSymantecSymantec Endpoint ProtectionSymRasMan.dll module. The specified module could not be found.
Second Error:
Source: RemoteAccess
Event ID: 20151
Error: The Control Protocol EAP in the Point to Point Protocol module C:WINDOWSSystem32rasppp.dll returned an error while initializing. The specified module could not be found.
Third Error:
Source: Rasman
Event ID: 20063
Error: Remote Access Connection Manager failed to start because the Point to Point Protocol failed to initialize. The specified module could not be found.
Fourth Error:
Source: Service Control Manager
Event ID: 7023
Error: The Remote Access Connection Manager service terminated with the following error: The specified module could not be found.
Fifth Error:
If tried to restart the service from RRAS mmc, it gives the following Error: «Routing and Remote Access cannot be started because of the following error.» Please see event log for more information: The service has returned a service-specific error code. (8007042a)
Cause
The default location of the file SymRasMan.dll is %SystemRoot%System32rastls.dll. On installing Symantec Antivirus or Symantec Endpoint Protection the default location is then changed and edited in the registry to C:Program FilesSAVSymRasMan.dll. After uninstallation this location is not reversed for Windows Server 2003 SP2 because it does create a backup of the key during the change/installation unlike Windows Small Business Server 2003
In SEP 12.1 it can result from a known issue described in TECH164677 — Clients show «No Symantec protection technologies are installed» after migrating the SEPM from 11.x to 12.1
Resolution
To resolve this issue follow the steps below:
- Click Start
- Click Run
- Type regedit
- Navigate to:
HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesRasManPPPEAP13 - Select the folder 13
- Change the value for keys: “ConfigUiPath”, “IdentityPath”, “InteractiveUIPath” and “Path” to:
%SystemRoot%System32rastls.dll - Navigate to:
HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesRasManPPPEAP25 - Select the folder 25
- Change the value for keys: “ConfigUiPath”, “IdentityPath”, “InteractiveUIPath” and “Path” to:
%SystemRoot%System32rastls.dll - Restart the computer (recommended not required)
- Start the RRAS service
Feedback
thumb_up
Yes
thumb_down
No
If the VPN Server incoming connections doesn’t work, because the Remote Access protocols rasgreeng.dll & IKEv2 failed to initialize, continue reading below to fix the problem.
Problem in details. After setting up Windows 10 as a VPN server, clients cannot connect to the VPN server because after entering the credentials, the connection is dropped without any obvious reason. When this happens, the following two errors are logged on the VPN server.
- Remote Access Connection Manager failed to start because the Protocol engine [rasgreeng.dll] failed to initialize. The specified module could not be found. (Event ID: 20063)
-
Remote Access Connection Manager failed to start because the Protocol engine [IKEv2] failed to initialize. The request is not supported.(Event ID: 20063)
How to FIX: Remote Access Connection Manager failed to start: rasgreeng.dll & IKEv2 failed to initialize on Windows 10 (Event ID 20063).
To fix the Event ID 20063 in Remote Access Connection Manager, perform the below steps:
1. On the VPN Server, open the Windows Services control panel: To do that:
-
- Press Windows + R keys to open the run command box.
- In the Search box, type: services.msc & click OK.
- Press Windows
2. In Services, double click to open the Remote Access Auto Connection Manager service.
3. Set the Startup type to Automatic and click Apply.
4. Then Start the service and click OK or restart the PC.
5. Try to connect to the VPN server from the clients. The problem should be resolved.*
* Note: If the problem is not fixed, apply the following steps.
1. Ensure that the following services on the VPN server are up and running:
-
DCOM Server Process Launcher (DcomLaunch)
-
Plug and Play (PlugPlay)
-
Remote Access Connection Manager (RasMan)
-
Remote Procedure Call (RPC) (RpcSs)
-
RPC Endpoint Mapper (RpcEptMapper)
-
Secure Socket Tunneling Protocol Service (SstpSvc)
-
Telephony (TapiSrv)
2. Repair the Windows system files, by running the following commands (in order) in Admin Command Prompt and then reboot your PC:
-
DISM /Online /Cleanup-Image /StartComponentCleanup
- DISM.exe /Online /Cleanup-image /Restorehealth
- sfc /scannow
That’s all folks! Did it work for you?
Please leave a comment in the comment section below or even better: like and share this blog post in the social networks to help spread the word about this solution.
If this article was useful for you, please consider supporting us by making a donation. Even $1 can a make a huge difference for us.
Здравствуйте перестал работать VPN в журнале следующие ошибки:
Код:20063 Источник: RemoteAccess
Произошел сбой при запуске диспетчера подключений удаленного доступа, так как не удалось инициализировать модуль протоколов [IKEv2]. The request is not supported.
Код:24 Источник:WMI
Поставщик событий попытался зарегистрировать запрос «select * from RemoteAccessError», целевой класс «RemoteAccessError» которого не существует в пространстве имен //./ROOT/Microsoft/Windows/RemoteAccess/Server. Запрос будет
пропущен
Код:24 Источник:WMI
Поставщик событий RAServerPSProvider попытался зарегистрировать запрос «select * from RemoteAccessError», целевой класс «RemoteAccessError» которого не существует в пространстве имен //./ROOT/Microsoft/Windows/RemoteAccess/Server.
Запрос будет пропущен
Код:18 Источник:RasSstp
Службе SSTP не удалось прочитать из реестра хеш сертификата SHA256, либо эти данные недопустимы. Допустимый хеш сертификата SHA256 должен иметь тип REG_BINARY и длину в 32 байта. Возможно, SSTP не удалось извлечь значение из реестра
из-за другой системной ошибки. Подробное сообщение об ошибке приведено ниже. Подключения SSTP не будут приняты на этом сервере. Исправьте ошибку и повторите попытку.
The system cannot find the file specified.
Event ID: 20063 Description: Remote Access Connection Manager failed to start because the Point to Point Protocol failed to initialize. %1 is not a valid Win32 application..
Full
Answer
Why is my event viewer displaying event ID 20063 error?
Event viewer is displaying Event ID: 20063 error «Remote Access Connection Manager failed to start because the Protocol engine [rasgreeng.dll] failed to initialize. The specified module could not be found.»
What is the remote access connection manager service?
The service is a dependency service to Remote Access Connection Manager and has been «disabled» on all the Windows 10 systems after the latest update. If this service is «started», the following errors are displayed in Event Viewer: Remote Access Connection Manager failed to start because the Protocol engine [IKEv2] failed to initialize.
What is the default run status of the routing and remote access?
What is the default run status of the «Routing and Remote Access» service? The service is a dependency service to Remote Access Connection Manager and has been «disabled» on all the Windows 10 systems after the latest update. If this service is «started», the following errors are displayed in Event Viewer:
How to run services.msc?
1. Press Windows + R for Run and then type Services.msc and then Enter.
How to check if a service has been stopped?
Follow the below methods and check if it helps, Method 1: 1. Press Windows + R for Run and then type Services.msc and then Enter . 2. Select Remote access connection manager and then right click and select Start if the service has been stopped. 3.
Why is Remote Access Connection Manager not starting?
Remote Access Connection Manager failed to start because it could not load one or more communication DLLs. Ensure that your communication hardware is installed and then restart the Remote Access Connection Manager service. If the problem persists, contact the system administrator. There was an unknown error.
Popular Posts:
If you see the rasman id 20063 error on your computer, check out these troubleshooting tips.
Approved: ASR Pro
Speed up your computer’s performance now with this simple download.
This issue requires space if both of the following conditions are encountered: You are upgrading a computer that is running Windows 2000 Service Pack 3 (SP3) to Windows 2000 Service Pack 4 (SP4). You have not configured a routing and then dial-up or dial-up connection on a computer that is performing a one-time upgrade to Windows 2000 SP4.
Keep track of an endless number of servers
Log events filter
Email to create web reports
Direct access to articles from Microsoft
Custom keywords for major search engines
Access to content coverage cost
Source
Microsoft ISA H.323 Firewall Filter
Description
An H.323 filter cannot be configured to register with an H.323 gatekeeper in order to detect the gatekeeper multicast discovery in use. Incoming H.323 calls will never succeed unless the filter is accredited by the gatekeeper. To set up a block to use opspecific gatekeeper, change some of the H.323 filter call control properties and enter the H.323 gatekeeper to register.
Description
The Remote Access Connection Manager was unable to start the specified point-to-point protocol, so it is initialized.
Description
The Remote Access Connection Manager error, so you start it because the point-to-point protocol could not be initialized. Currently, there is never a Connection Server to handle a connection request.
Splunk Windows Event Log Analysis Application
Build a great reporting interface with Splunk, especially for security and event management (SIEM) personnel who often associate collected Windows events with www.eventid.net.
More …
Splunk Application for Cisco ASA Log Analyzer
Approved: ASR Pro
ASR Pro is the world’s most popular and effective PC repair tool. It is trusted by millions of people to keep their systems running fast, smooth, and error-free. With its simple user interface and powerful scanning engine, ASR Pro quickly finds and fixes a broad range of Windows problems — from system instability and security issues to memory management and performance bottlenecks.
Get dramatically improved visibility of the Cisco ASA Firewall logs with a free app.Firegen Application for Cisco ASA Splunk. Use dashboards designed as a threat intelligence optimization process.
More … No Limits
Keep track of the number of servers
Log Event Filter
Create reports by email and on the web
Direct access to articles from Microsoft
Keywords suitable for major search engines
Access to quality content
The H.323 filter is not configured to register an H.323 gatekeeper trying to find a new one using gatekeeper multicast discovery. Incoming H.323 voice messages will not be successful until the filter is permanently registered by the gatekeeper. To tilt the filter to use a single gatekeeper, modify the call control components of the H.323 filter and enter the H.323 gatekeeper for which you want to register.
RAS connection failed during manager focus because point-to-point protocol initialization completed.
С Remote Access Connection An error occurred while starting the dispatcher because the point-to-point protocol could not be initialized. Of course, there are currently no platform connection servers available to request a connection.
Splunk Windows Event Log Analysis Application
Build a great reporting interface with Splunk, the leader in security information and event management (SIEM), and link collected Windows events to www.eventid.net.
Cisco ASA Log Analyzer Splunk Application
Get better visibility into the Cisco ASA Firewall logs with any free Cisco ASA Splunk Firegen app. Use dashboards designed to streamline your threat intelligence process.
Unable To Start Routing And Remote Access Server (RRAS) (event ID: 7023, 20070, 20151, 20063) After Uninstalling Symantec Antivirus / Symantec Endpoint Protection
Updated:
Products
Endpoint Security
Problem / Introduction
Why does this error usually appear after uninstalling Symantec Antivirus / Endpoint? “Unable to start RRAS (Event ID: 7023, 20070, 20151, 20063)”
Source: Remote Access
Event ID: 20070
Error: The Point-to-Point Protocol Subsystem was unable to load drive C: Program Files Symantec Symantec Endpoint Protection SymRasMan.dll. The specified module is not observed. Error:
Source:
second remote access
Event ID: 20151
Error: EAP control protocol in point-to-point protocol module C: WINDOWS System32 rasppp.dll also returned an error during initialization. The specified module could not be recognizednan.
Third error:
Source: Rasman
Event ID: Remote 20063
error: The Access Connection Manager could not be started because the point-to-point protocol could not be initialized. The specified module could not be found.
Fourth error:
Source: Service Control Manager
Event ID: 7023
Error: The Remote Access Connection Manager service was interrupted due to the following error: The specified module could not be found permanently.
Fifth error:
When you try to restart your computer using the mmc RRAS service, you receive the following error: “Remote Routing and Access could not be started due to a previous error.” For more information about the log, see Event: Service returned a large error code specific to the service. (8007042a)
Reason
In fact,% SystemRoot% System32 rastls.dll is the cause of the SymRasMan.dll file failure. When you install Symantec Antivirus or Symantec Endpoint Protection, the default path is modified and edited.I’m in the registry at C: Program Files SAV SymRasMan.dll. After uninstallation, this location does not really change to the opposite for Windows Server 2003 SP2, because unlike Windows Small Business Server 2003, the key is backed up during edit / installation
On September 1st, this idea may be the result of a known issue in TECH164677: After upgrading from sepm 11.x to 12.1, customers report “Symantec security technology not installed”
Resolution
- Click Start.
- Click Run.
- Enter regedit.
- Go to:
HKEY_LOCAL_MACHINE SYSTEM CurrentControlSet Services RasMan PPP EAP 13 - Select folder 13
- Change the key value: “ConfigUiPath”, “IdentityPath”, “InteractiveUIPath” and “Path” to:
% SystemRoot% System32 rastls.dll - Go to:
HKEY_LOCAL_MACHINE SYSTEM CurrentControlSet Services RasMan PPP EAP 25 - Select file 25
- Change the value to contain the keys: “ConfigUiPath”, “InteractiveUIPath”, “identitypath” and “Path” to:
% SystemRoot% System32 rastls.dll - R
Speed up your computer’s performance now with this simple download.
Today I experienced another issue with Windows 10 upgrade (to the Fall Creators Update) and the VPN server functionality. After quick research, it turned out that errors are written to the event log after each client’s attempt to connect:
- Remote Access Connection Manager failed to start because the Protocol engine [rasgreeng.dll] failed to initialize. The specified module could not be found.
- Remote Access Connection Manager failed to start because the Protocol engine [IKEv2] failed to initialize. The request is not supported.
Looking for mentioned .dll led to dead end — no such .dll exists on any my Windows 10 machines. However, then I checked the services and noticed that one of them related to remote access — Remote Access Auto Connection Manager (RasAuto) is not running. So I changed the startup type option from Manual to Automatic, restarted PC, and everything worked like a charm.
I am experiencing a problem with Windows VPN on my Lenovo Ideapad, running Windows 10 1909. The problem makes a lot of network-related settings pages work very slowly. For example, it takes a long time for the list of WiFi networks to load when I click on the icon in the taskbar (and it leaves out the VPN networks). The network pages in the Settings app also work very slowly. Finally, when I try to connect to a VPN (after getting to the page), it gets stuck saying “Connecting”. The VPN I use is L2TP/IPSec with PSK, using the built-in VPN provider.
I found the following errors in Event Viewer (System):
- RasMan – 20027 – Remote Access Connection Manager failed to start because NDISWAN could not be opened.
- RasMan – 20063 – Remote Access Connection Manager failed to start because the Protocol engine [C:WINDOWSsystem32vpnike.dll] failed to initialize. The system cannot find the device specified.
- Service Control Manager – 7023 – The Remote Access Connection Manager service terminated with the following error:
The system cannot find the device specified.
These errors occur in this order whenever I try to use those network settings pages or connect to a VPN.
My problem is just about identical to the one discussed on this SpiceWorks thread. However, I have tried everything there and it did not work. I’m honestly not sure how removing vpnike.dll fixed the problem for the person on SpiceWorks, considering that there wouldn’t be anything to handle IKE…
Things I have tried:
sfc /scannow- Registering vpnike.dll using
regsvr32 netsh int ip reset c:resetlog.txtand rebootingdism /Online /Cleanup-Image /ScanHealth(No component store corruption detected)- Comparing vpnike.dll and ndiswan.sys to files on other computers – I took a SHA256 hash and it matched other Windows 10 1909 computers.
- Renaming vpnike.dll
- Renaming vpnike.dll and then running
sfc /scannow– This allows the settings pages to work, but when I try to connect to a VPN, it says “A device of that type does not exist.” No error in the event log. - Restarting, renaming vpnike.dll, running
sfc /scannow, and renaming vpnike.dll again… (Still says “A device type was specified that does not exist.”) - Renaming ndiswan.sys
- Renaming ndiswan.sys and running
sfc /scannow
Если вы подтвердили ошибку rasman id 20063 на своем мобильном компьютере, ознакомьтесь с этими советами по устранению неполадок.
Для данной публикации требуется место, если обнаружены оба следующих нарушения: Вы обновляете компьютер, на котором работает Windows 2000 с пакетом обновления SP3 или выше, до Windows 2000 с пакетом обновления 4 (SP4). Вы не настроили маршрутизацию и не сопровождались коммутируемым или коммутируемым подключением на компьютере, который, несомненно, выполняет одноразовое обновление до Windows 2000 SP4.
<раздел>
Следите за количеством компьютеров
Фильтр событий журнала
Создавайте отчеты по электронной почте и в Интернете
Прямой доступ к статьям из Microsoft
Ключевые слова, подходящие для основных поисковых систем
Доступ, если вы хотите качественный контент
Фильтр H.323 не настроен таким образом, чтобы вы могли зарегистрировать привратник H.323, пытающийся найти новый, используя обнаружение многоадресной рассылки привратника. Входящие голосовые сообщения H.323 не будут успешными до тех пор, пока фильтр не будет постоянно зарегистрирован привратником. Чтобы наклонить фильтр для использования только одного привратника, измените компоненты управления вызовом фильтра H.323 и введите привратник H.323, для которого вы хотите зарегистрироваться.
Соединение RAS не удалось во время работы босса группы, так как инициализация протокола точка-точка завершена. <Описание ошибки>
С Подключение удаленного доступа Произошла ошибка при установке диспетчера, потому что протокол точка-точка не может быть просто инициализирован. Конечно, в настоящее время нет доступных серверов подключения платформы для запроса нового подключения.
Приложение для анализа журнала событий Windows Splunk
Создайте отличный интерфейс отчетности с помощью Splunk, директора по безопасности информации и управления событиями (SIEM), в дополнение к связыванию собранных событий Windows с www.eventid.net.
Приложение Splunk для анализатора журналов Cisco ASA
Получите лучшую наглядность в записях межсетевого экрана Cisco ASA с помощью любого бесплатного практического приложения Cisco ASA Splunk Firegen. Используйте информационные панели, предназначенные для оптимизации процесса анализа угроз.
Невозможно запустить сервер маршрутизации и удаленного доступа (RRAS) (идентификатор события: 7023, 20070, 20151, 20063) после удаления Symantec Antivirus / Symantec Endpoint Protection
Обновлено:
Продукты
Endpoint Security
Проблема / Введение
Почему после удаления Symantec Antivirus и Endpoint обычно появляется ошибка элемента? «Невозможно запустить RRAS (идентификатор события: 7023, 20070, 20151, 20063)»
Источник: удаленный доступ
Идентификатор события: 20070
Ошибка: подсистеме протокола точка-точка не удалось загрузить диск C: Program Files Symantec Symantec Endpoint Protection SymRasMan.dll. Указанный модуль не наблюдается. Ошибка:
Источник:
второй удаленный доступ
Идентификатор события: 20151
Ошибка: протокол управления EAP в модуле протокола точка-точка C: WINDOWS System32 rasppp.dll также вернул 1 ошибку во время инициализации. Указанный модуль не обязательно может быть распознан.
Третья ошибка:
Источник: Расман
Идентификатор события: Remote 20063
ошибка: диспетчер подключений доступа, скорее всего, не запустится, потому что протокол точка-точка не может быть инициализирован. Указанный модуль точно не найден.
Четвертая ошибка:
Источник: диспетчер управления службами
Идентификатор события: 7023
Ошибка: служба диспетчера подключений удаленного доступа была прервана из-за ошибки при отслеживании: указанный модуль не может быть обнаружен навсегда.
Пятая ошибка:
Когда вы пытаетесь повторно активировать компьютер с помощью службы mmc RRAS, покупатели получают следующую ошибку: «Не удалось запустить удаленную маршрутизацию и доступ из-за предыдущей ошибки». Дополнительные сведения о журнале см. В разделе Событие: служба вернула большой код ошибки, специально предназначенный для службы. (8007042a)
Причина
Фактически,% SystemRoot% System32 rastls.dll является причиной сбоя файла SymRasMan.dll. Когда вы и ваша семья устанавливаете Symantec Antivirus или Symantec Endpoint Protection, весь путь по умолчанию изменяется и редактируется. Я бы сказал, что реестр находится в C: Program Files SAV SymRasMan.dll. После удаления это расположение не меняется на противоположное только для Windows Server 2003 SP2, потому что, в отличие от Windows Small Business Server 2003, резервная копия ключа создается во время изменения / установки
1 сентября эта мысль может быть результатом известной ситуации в TECH164677: после обновления с sepm 11.x до 12.1 клиенты сообщают, что «технология безопасности Symantec никогда не устанавливалась»
Разрешение
Здравствуйте перестал работать VPN в журнале следующие ошибки:
Код:20063 Источник: RemoteAccess
Произошел сбой при запуске диспетчера подключений удаленного доступа, так как не удалось инициализировать модуль протоколов [IKEv2]. The request is not supported.
Код:24 Источник:WMI
Поставщик событий попытался зарегистрировать запрос «select * from RemoteAccessError», целевой класс «RemoteAccessError» которого не существует в пространстве имен //./ROOT/Microsoft/Windows/RemoteAccess/Server. Запрос будет
пропущен
Код:24 Источник:WMI
Поставщик событий RAServerPSProvider попытался зарегистрировать запрос «select * from RemoteAccessError», целевой класс «RemoteAccessError» которого не существует в пространстве имен //./ROOT/Microsoft/Windows/RemoteAccess/Server.
Запрос будет пропущен
Код:18 Источник:RasSstp
Службе SSTP не удалось прочитать из реестра хеш сертификата SHA256, либо эти данные недопустимы. Допустимый хеш сертификата SHA256 должен иметь тип REG_BINARY и длину в 32 байта. Возможно, SSTP не удалось извлечь значение из реестра
из-за другой системной ошибки. Подробное сообщение об ошибке приведено ниже. Подключения SSTP не будут приняты на этом сервере. Исправьте ошибку и повторите попытку.
The system cannot find the file specified.