Modular Block System: Emergency Stop Circuits
6-25
The acknowledgements
FbL1 and FbL2 are also monitored in the static
condition. If there are discrepancies between the set and true condition, an
error message will be issued (
ENBL = 0) and the contactors will be
switched off immediately (
K1 = 0 and K2 = 0). The error will need to be
reset.
It is possible to reset errors via the input parameter
RSET both when ON =
0 and when
ON = 1. However, a prerequisite for setting the enable and,
when
ON = 1, switching on the contactors, is that the signals from the
feedback loops are correct.
Error messages
Any fault that is detected will be stored in the corresponding error data
word (
SSNR) of the administration data block (1st data block), until the
fault has been fully dealt with.
• Error messages in the administration data block
— Bit 00:
Fault as the signal changes at input parameter
ON,
feedback loop 1 (
FbL1) remains open
Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter
TFbL and all conditions and
then reset (input parameter
RSET)
— Bit 01:
Fault as the signal changes at input parameter
ON,
feedback loop 1 (
FbL1) remains closed
Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter
TFbL and all conditions and
then reset (input parameter
RSET)
— Bit 02:
Fault as the signal changes at input parameter
ON,
feedback loop 2 (
FbL2) remains open
Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter
TFbL and all conditions and
then reset (input parameter
RSET)
List of Pilz PSS Series Guides:
Guidesimo.com webproject is not a service center of Pilz trademark and does not carries out works for diagnosis and repair of faulty Pilz PSS Series equipment. For quality services, please contact an official service center of Pilz company. On our website you can read and download documentation for your Pilz PSS Series device for free and familiarize yourself with the technical specifications of device.
More Adapter Devices:
-
Paradyne 6512
TSTLINEALMPWRETHERNETTMTM98-16014a-01TM 1SuperLine AdapterInstallation InstructionsDocument Number 6512-A2-GN10-20January 1999SuperLineAdapterContents: Important Safety Instructions What Your SuperLine Adapter Does Package Checklist Optional Hardware (Not Supplied) Front Panel Indicators SuperLine Adapter Rear Panel Installing Your SuperLine Adapter Troubleshooting Yo …
6512 Adapter, 28
-
Linksys WPC54G
F. The Setup Wizard will askyou to review your settingsbefore it starts to copy files.Click Next if you are satis-fied with your settings, orclick Back to change anysettings. G. After the files have beensuccessfully copied, youwill see Figure G. Click theExit button.Proceed to Step 2.WPC54GPackage Contents• One Wireless-G Notebook Adapter (1)• One Setup Wizard CD-ROM with UserGuide (2)• On …
WPC54G Adapter, 2
-
Mini Gadgets LMWiFiPower
Updated 06/30/2016 1 Version 1.0 POWER ADAPTER WITH HIDDEN CAMERA SKU: LMWiFiPower THANK YOU FOR PURCHASING THE LMWIFIPOWER Please read this manual before operating the LMWiFiPower and keep it handy. The most ubiquitous, unnoticeable devices nowadays are chargers. With the average Joe carrying at least two or three rechargeable electronic devices on their person every da …
LMWiFiPower Adapter, 5
-
D-Link DFE-530TX
Contents of Package: • DFE-530TX+ Ethernet PCI Adapter • Printed Quick Installation Guide • CD with Manual and Drivers If any of the above items are missing, please contact your reseller. Before you start, make sure to turn off your computer and unplug the power cord. Note: To avoid damage caused by static electricity, make sure to properly ground yourself by first touching a metal par …
DFE-530TX Adapter, 6
Recommended Documentation:
- 5 Янв 2007
Контроллер Pilz PSS3100 — коды сообщений.
Суть проблемы: листогиб AMADA. В состав входят ЧПУ на Ampro LittleBoard и контроллер Pilz. После простоя 4 дня в холоде включили — выскочила ошибка готовности контролера. Сервисные московсие фирмы на каникулах. У нас ни схем, ни документации, ни программ для контроллера.
Внешне проверяли релюшки, датчики, разъемы — все в порядке. Научный тык не прошел.
Вопрос может кто владеет информацией по расшифровке кодов, отображаемых на LED контроллера?
- 5 Янв 2007
Покопайся на ссылка скрыта от публикации в разделе Download. Может найдешь чего…
- 7 Янв 2007
Копался… и на ссылка скрыта от публикации / тоже… даже зарегился там и в техподдержке спросил, однако молчат.
- 8 Янв 2007
Кстати, станок подняли. Решение пришло элементарное. Раз станок от холода загнулся, надо его прогреть.
Взяли, да и прогрели тепловентилятором электрошкаф с контроллером и ЧПУ — ошибка исчезла.
НО вопрос по кодам не снимаю. Надо бы узнать, чему именно не нравиться холод. Почему-то другие станки нормально его перенесли.
Commissioning and Operation
If the module has not achieved the correct operating status, there are
several options available for error diagnostics:
• Evaluating the operating status LED
• Evaluating the output paramter ERR of SB 236
(see ST SB ControlNet — Software Manual)
• Evaluating the data block for status information DB_S
(see ST SB ControlNet — Software Manual)
• Bus diagnostics via the NAP-interface for the module
For this purpose an additional monitoring tool is required. Further
information can be found in the relevant operating mnaual for the
monitoring tool.
Operation
The module is operated on ControlNet using a software package from
Pilz. It contains the standard function block SB 236 which runs in the
standard section of the PSS. It is used for communication between the
PSS and other ControlNET subscribers (send/receive data).
More detailed information on SB 236 can be found in a separate operating
manual «ST SB ControlNet — Software Manual». This is supplied with the
software package.
7-2
PSS(1) ControlNet Adapter — Hardware Manual
Modular Block System: Emergency Stop Circuits
6-25
The acknowledgements
FbL1 and FbL2 are also monitored in the static
condition. If there are discrepancies between the set and true condition, an
error message will be issued (
ENBL = 0) and the contactors will be
switched off immediately (
K1 = 0 and K2 = 0). The error will need to be
reset.
It is possible to reset errors via the input parameter
RSET both when ON =
0 and when
ON = 1. However, a prerequisite for setting the enable and,
when
ON = 1, switching on the contactors, is that the signals from the
feedback loops are correct.
Error messages
Any fault that is detected will be stored in the corresponding error data
word (
SSNR) of the administration data block (1st data block), until the
fault has been fully dealt with.
• Error messages in the administration data block
— Bit 00:
Fault as the signal changes at input parameter
ON,
feedback loop 1 (
FbL1) remains open
Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter
TFbL and all conditions and
then reset (input parameter
RSET)
— Bit 01:
Fault as the signal changes at input parameter
ON,
feedback loop 1 (
FbL1) remains closed
Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter
TFbL and all conditions and
then reset (input parameter
RSET)
— Bit 02:
Fault as the signal changes at input parameter
ON,
feedback loop 2 (
FbL2) remains open
Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter
TFbL and all conditions and
then reset (input parameter
RSET)
+7 (495) 215-16-67
8 (800) 333-16-67
с 9:00-19:00 — ежедневно (МСК)
Заказать звонок
×
Обратный звонок
Представьтесь
Номер вашего телефона
Ваш вопрос
я даю согласие Shopozz на обработку персональных данных
в соответствии с Федеральным законом от 27.07.2006 года №152-ФЗ «О персональных данных», на условиях и для целей, определенных Политикой конфиденциальности.
Доставка товаров с аукциона eBay и интернет-магазинов США в
Россию (Москва, Санкт-Петербург, Новосибирск, Екатеринбург,
Казань, Нижний Новгород, Челябинск, Красноярск, Самара, Уфа,
Ростов-на-Дону, Омск, Краснодар, Воронеж, Волгоград, Пермь и
другие города).
© Shopozz — сервис покупок за рубежом
Guidesimo.com webproject is not a service center of Pilz trademark and does not carries out works for diagnosis and repair of faulty Pilz PSS Series equipment. For quality services, please contact an official service center of Pilz company. On our website you can read and download documentation for your Pilz PSS Series device for free and familiarize yourself with the technical specifications of device.
More Adapter Devices:
-
SIIG VV-CV0012-S1
1Introducing the DP ADD2 PCIe DVI AdapterThe DP ADD2 PCIe DVI Adapter is an economical way toadd a second monitor to PCs using select Intel PCIExpress based graphics controllers. Increase yourproductivity by using it as an extended desktop or as alarger/different display for your main screen.Features and Benefits• Adds a DVI-D port for an additional monitor• Multiple display functionality: pr …
VV-CV0012-S1 Adapter, 8
-
ZyXEL Communications G-220 V2
Copyright © 2008. All rights reservedZyXEL G-220 v2802.11g Wireless USB AdapterQuick Start GuideVersion 2.1.13/2008Edition 1CONTENTSENGLISH 2 DEUTSCH 14 ESPANOL 26 FRANCAIS 38 ITALIANO 50 РУССКИЙ 62 SVENSKA 74 繁體中文 86 …
G-220 V2 Adapter, 95
-
D-Link DG-102S
DG-102S Thank you for choosing the D-Link DG-102S, the value leader for VoIP products. The D-Link DG-102S VoIP Station Gateway links traditional telephony networks to IP networks with conventional telephony devices such as analog phones or fax machines. The DG-102S includes two loop start Foreign Exchange Subscriber (FXS) interfaces with normal RJ-11 telephone connectors that provide voice/fax c …
DG-102S Switch, 1
-
SanDisk Connect
Getting Startedfor Connect Wireless StickPlug the SanDisk Connect™ Wireless Stick into a computer or USB-AC adapter to ensure that it’s fully charged. A full charge can take up to 2 hours. Device cannot be connected using a USB cable.Download and install the SanDisk Connect app on your mobile device. SanDisk® has many apps available, so please ensure you select the correct application, matchi …
Connect Adapter, 1
-
Tripp Lite U437-001-C
11111 W. 35th Street, Chicago, IL 60609 USA tripplite.com/supportCopyright © 2020 Tripp Lite.USB-C to 3.5 mm Audio Adapter with PD ChargingModel: U437-001-COwner’s ManualEste manual esta disponible en español en la página de Tripp Lite: tripplite.comCe manuel est disponible en français sur le site Web de Tripp Lite : tripplite.comtРусскоязычная версия настоящего …
U437-001-C Adapter, 8
Recommended Documentation:
Please note:
• Safety-oriented input signals must operate in normally energised mode.
• Make sure that in the user program the «0»-Signal of the module will
switch-off the relevant outputs.
• Connecting one «0 V»-terminal is sufficient.
• Neighbouring inputs must not be assigned the same pulse.
• Copper wiring should be used that can withstand temperature of 75 °C.
• Torque setting on the screw terminals should be to 0.5 … 0.6 Nm.
Faults
If a fault in one of the modules or a wiring-error is detected, the controller
goes into a STOP condition, switches off all the outputs and sends a
message to the display. The display on the programmer’s error stack can
be used to locate the error.
Operating Manual
3
List of Pilz PSS Series Guides:
Guidesimo.com webproject is not a service center of Pilz trademark and does not carries out works for diagnosis and repair of faulty Pilz PSS Series equipment. For quality services, please contact an official service center of Pilz company. On our website you can read and download documentation for your Pilz PSS Series device for free and familiarize yourself with the technical specifications of device.
More Safety Equipment Devices:
-
Ansell MICROGARD 701 PAPR
MICROGARD LimitedHead Office9 Saltmarsh CourtPriory Park · HessleKingston upon Hull United Kingdom HU4 7DZTel +44 (0) 1482 625444 Fax +44 (0) 1482 630400Email [email protected] 701 Instructions for UseVersion 11.02.19EC Type Examination conducted by SGS Fimko Oy, P.O. Box 30 (Särkiniementie 3), 00211 HELSINKI, Finland. Notified Body CE 0598 …
MICROGARD 701 PAPR Safety Equipment, 90
-
BGS technic 3620
BGS technic KGBandwirkerstr. 342929 WermelskirchenTel.: 02196 720480Fax.: 02196 [email protected]© BGS technic KG, Vervielfältigung und Weiterverwendung verbotenArt. 3620 Atemschutzmasken ACHTUNG Lesen und verstehen Sie alle Anweisungen und Informationen in dieser Bedienungsanleitung. Die Nichtbeachtung der unten aufgeführten Anweisungen und Informationen kann zu sch …
3620 Safety Equipment, 9
-
Lumiance INSAVER 225
INSAVER 225 HE EMERGENCY CONE3111-447 (190308)min. Amin. B100min. C A B CInsaver 225 2×18 500 980 150Insaver 225 2×26 500 980 150Ø 228 +/-2Min 1 — Max 25min. 4 x 0,75 mm 2min. 4 x 1,5 mm 2840N L LUNSWITCHEDMAINSSWITCHEDMAINS2x Fuse F2H 250V SandfilledN L LNL L2311325 64b4a4c21Insaver 225 2x18WTC-D 18W G24-q2Insaver 225 2x26WTC-D 26W G24-q3213Click (3x) …
INSAVER 225 Safety Equipment, 2
-
Fbt LIGHT
VAIE 5500FBT ELETTRONICA S.p.A. — Via Paolo Soprani, 1 — ZONA IND. SQUARTABUE — 62019 RECANATI (MC) — ITALYTEL. 071750591 r.a. — FAX 0717505920 — P.O. BOX 104 — E-mail: [email protected] — www.fbt.it INSTRUCTIONS FOR USEVAIE 5502500W / 2 ZONES“LIGHT” Wall-mounted voice evacuation system …
LIGHT Safety Equipment, 44
Recommended Documentation:
Я не понял, про какую батарейку Вы имели ввиду.
Теперь все ясно.
У Вас их две.
Одна находится в главном компьютере — DELEM 65TW. Она питает BIOS материнской платы. Если эта батарейка садится, то сбрасывается CMOS, и параметры BIOS возвращаются к заводским настройкам.
Я разбирал DELEM 65W, там стоит ноутбучная материнская плата для процессора CELERON с пассивным охлаждением. Поэтому, если села эта батарейка, ничего страшного не произойдет.
А вот со второй сложнее. Она питает программируемое защитное реле PILZ. Когда напряжение на батарейке станет 2.5, появляется предупреждение S04. Заменить батарейку требуется за 2 мин., иначе все данные будут уничтожены.
Покупайте новую батарейку, и замените ее при выключенном питание не более, чем за 2 мин.
Удачи.
Войти или зарегистрироваться
Тема в разделе «WASM.HARDWARE», создана пользователем 4ygynOK, 30 окт 2011.
-
4ygynOK
New Member
- Публикаций:
-
0
- Регистрация:
- 2 апр 2010
- Сообщения:
- 5
Форумчане требуется документация по этому устройству, желательно конечно на русском, но на любых других языках тоже приветствуется. Особенно буду рад по документации об ошибках, их расшифровка и т.п.
Может кто с ними уже работал, какие могут возникать проблемы и как их устранять. В общем любая информация приветствуется.
P.S. Заранее спасибо.
(Вы должны войти или зарегистрироваться, чтобы ответить.)
Показать игнорируемое содержимое
- Ваше имя или e-mail:
- У Вас уже есть учётная запись?
-
- Нет, зарегистрироваться сейчас.
- Да, мой пароль:
-
Забыли пароль?
-
Запомнить меня
Поиск
-
- Искать только в заголовках
- Сообщения пользователя:
-
Имена участников (разделяйте запятой).
- Новее чем:
-
- Искать только в этой теме
- Искать только в этом разделе
- Отображать результаты в виде тем
-
Быстрый поиск
- Последние сообщения
Больше…
Modular Block System: Emergency Stop Circuits
6-25
The acknowledgements
FbL1 and FbL2 are also monitored in the static
condition. If there are discrepancies between the set and true condition, an
error message will be issued (
ENBL = 0) and the contactors will be
switched off immediately (
K1 = 0 and K2 = 0). The error will need to be
reset.
It is possible to reset errors via the input parameter
RSET both when ON =
0 and when
ON = 1. However, a prerequisite for setting the enable and,
when
ON = 1, switching on the contactors, is that the signals from the
feedback loops are correct.
Error messages
Any fault that is detected will be stored in the corresponding error data
word (
SSNR) of the administration data block (1st data block), until the
fault has been fully dealt with.
• Error messages in the administration data block
— Bit 00:
Fault as the signal changes at input parameter
ON,
feedback loop 1 (
FbL1) remains open
Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter
TFbL and all conditions and
then reset (input parameter
RSET)
— Bit 01:
Fault as the signal changes at input parameter
ON,
feedback loop 1 (
FbL1) remains closed
Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter
TFbL and all conditions and
then reset (input parameter
RSET)
— Bit 02:
Fault as the signal changes at input parameter
ON,
feedback loop 2 (
FbL2) remains open
Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter
TFbL and all conditions and
then reset (input parameter
RSET)
Please note:
• Safety-oriented input signals must operate in normally energised mode.
• Make sure that in the user program the «0»-Signal of the module will
switch-off the relevant outputs.
• Connecting one «0 V»-terminal is sufficient.
• Neighbouring inputs must not be assigned the same pulse.
• Copper wiring should be used that can withstand temperature of 75 °C.
• Torque setting on the screw terminals should be to 0.5 … 0.6 Nm.
Faults
If a fault in one of the modules or a wiring-error is detected, the controller
goes into a STOP condition, switches off all the outputs and sends a
message to the display. The display on the programmer’s error stack can
be used to locate the error.
Operating Manual
3
Pilz PSS Series: Manuals, Instructions
-
TDK-Lambda
G10-500
Series Programmable DC Power Supplies 5kW in 1U 0-600V/ 0-500A Built in LAN, USB, RS-232 & RS-485 Interface Optional Interface: IEEE488.2 (GPIB) SAFETY & INSTALLATION MANUAL This Manual Covers Models: G10-500 G80-65 GB10-500 GB80-65 G20-250 G100-50 GB20-250 GB100-50 G30-170 G150-34 GB30-170 GB150-34 G40-125 G300-17 GB40-125 GB300-17 G60-85 G600-8.5 GB60-85 GB600-8.5 Manual Supplements …
G10-500 Power Supply, 56
-
KEPCO
BOP 2X-DE Series
©2019, KEPCO, INC 1Data subject to change without notice 228-1921 KEPCO, INC. 131-38 SANFORD AVENUE FLUSHING, NY. 11355 U.S.A. TEL (718) 461-7000 FAX (718) 767-1102www.kepcopower.com email: [email protected] START GUIDEKEPCOAn ISO 9001 Company.BOP2X-DE SERIESBIPOLAR 2X-DE SERIESDUAL CHANNEL OPERATIONAL POWER SUPPLYI — INTRODUCTION1.1. SCOPE OF …
BOP 2X-DE Series Power Supply, 8
-
Corsair
TX850M
Professional Series GoldATX Cable EPS Cable PCI-E Cable SATA Cable 4-Pin Peripheral Cable Floppy CableAX6501x 600mm (m) 1x 650mm (m) 4x 600mm (m) 2x 400mm, 550mm, 700mm, 850mm (m) 2x 400mm, 550mm, 700mm, 850mm (m) (no floppy) 2x 101mm2x 400mm, 550mm (m)2x 400mm, 550mm, 700mm, 850mm (m)2x 400mm, 550mm (m)2x 400mm, 550mm, 700mm, 850mm (m)2x 400mm, 500mm (m)3x 450mm, 550mm, 650mm, 750mm (m)Profession …
TX850M Power Supply, 3
-
Altronix
eFlow102NV
Rev. 102NVRP052213More than just power.TMPower Supply/ChargersInstallation GuideModels Include:Installing Company: ________________ Service Rep. Name: ______________________________________ Address: ___________________________________________________ Phone #: _____________________eFlow102NV/eFlow102NXV — 10A @ 12VDCeFlow102N8V/eFlow102NX8V — 10A @ 12VDC — Eight (8) Fused OutputseFlow102N …
eFlow102NV Power Supply, 16
Recommended Documentation:
Modular Block System: Emergency Stop Circuits
6-25
The acknowledgements
FbL1 and FbL2 are also monitored in the static
condition. If there are discrepancies between the set and true condition, an
error message will be issued (
ENBL = 0) and the contactors will be
switched off immediately (
K1 = 0 and K2 = 0). The error will need to be
reset.
It is possible to reset errors via the input parameter
RSET both when ON =
0 and when
ON = 1. However, a prerequisite for setting the enable and,
when
ON = 1, switching on the contactors, is that the signals from the
feedback loops are correct.
Error messages
Any fault that is detected will be stored in the corresponding error data
word (
SSNR) of the administration data block (1st data block), until the
fault has been fully dealt with.
• Error messages in the administration data block
— Bit 00:
Fault as the signal changes at input parameter
ON,
feedback loop 1 (
FbL1) remains open
Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter
TFbL and all conditions and
then reset (input parameter
RSET)
— Bit 01:
Fault as the signal changes at input parameter
ON,
feedback loop 1 (
FbL1) remains closed
Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter
TFbL and all conditions and
then reset (input parameter
RSET)
— Bit 02:
Fault as the signal changes at input parameter
ON,
feedback loop 2 (
FbL2) remains open
Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter
TFbL and all conditions and
then reset (input parameter
RSET)
Table of Contents for Pilz PSS Series:
-
PSS PS230 4 Bedienungsanleitung Technische Daten Elektrische Daten Versorgungsspannung 120 V AC/230 V AC, automatische Umschaltung Toleranzbereich -15 … +10 % Frequenzbereich 48 … 62 Hz Ausgangsspannung 5,0 V DC/max. Dauerbelastung: 10 A 12 V DC/ 0,25 A kurzschlusssicher, strombegrenzt Anschlussleistung 80 VA Einschaltstrom 10 A (15 A im warmen Zustand) Arbeitsweise primärgetaktet Batterie Typ: Lithium 3,6 V, Größe AA Lebensdauer ca. 2
-
PSS PS230 2 Handleiding Inleiding Deze handleiding geldt voor de voeding PSS PS230 vanaf versie 1.3. Kort samengevat De voedingsmodule PS230 levert de interne spanning voor de werking van een moduuldrager en 12 V DC voedingsspanning voor de programme- ring van het gebruikersgeheugen. De module kan naar keuze met 230 of 120 V AC gevoed worden. De ingebouwde batterij dient als buffer van de realtime klok en de geheugenbouwstenen van het standaardonderdeel,
-
PSS PS230 4 Manuel d’utilisation Exigences pour la batterie en cas d’installations pour lesquelles l’homologation UL est importante : — Batterie BBCV2 — Max. abnormal charging current: 5 mA or better Caractéristique techniques Données électriques Tension d’alimentation 120 V AC/230 V AC, commutation automatique Plage de tolérances -15 à +10 % Plage de fréquences 48 à 62 Hz Tension de sortie 5,0 V DC/max. Charge permanente : 10 A
-
Bedienungsanleitung 3 DEUTSCH Nach korrekter Inbetriebnahme muss die LED «POWER» leuchten. Bitte beachten Sie: • Leitungsmaterial aus Kupferdraht verwenden, dessen Isolation eine Temperaturbeständigkeit von 75 °C hat. • Das Anzugsdrehmoment der Schrauben auf den Anschlussklemmen muss 0,5 … 0,6 Nm betragen. WARNUNG! Vor dem Stecken und Ziehen eines Steckverbinders alle Spannungen ab- schalten! Durch Berühren leitender Teile können Sie sonst bei angelegter Spannung durch einen Stromschlag schwer verletzt oder getö
-
1Handleiding NEDERLANDS Inhoud Inleiding 2 Kort samengevat 2 Ingebruikname 2 Stekkerbezetting 3 Batterie 3 Technische gegevens 4 PSS PS230
-
The spirit of safety. Sicherheitssteuerungen Systemfamilie PSS Programmable Safety Control PSS-Range Automates de sécurité Gamme PSS Veiligheidsbesturingen Systeemfamilie PSS PSS PS230 Bedienungsanleitung/Operating Manual/Manuel d’utilisation/Handleiding Sach-Nr./Item No./Référence/Artikelnr. 18559-4NL-04
-
3Operating Manual ENGLISH Please note: • Copper wiring used must be able to withstand a temperature of 75 °C. • Torque setting of the screw terminals must be to 0.5 … 0.6 Nm. WARNING! Switch off all voltages before inserting or removing a connector. If you touch conductive components while voltage is applied, you could suffer serious injury or death due to electric shock. Pin Assignment The power supply has a 5-pin screw connector for connecting up the supply vo
-
PSS PS230 2 Operating Manual Introduction This operating manual is valid for the power supply PSS PS230 from Version 1.3. Overview The PS230 Power Supply provides the internal voltage required to operate the module rack, and the 12 V DC required to program the user memory. It can be operated with either 230 or 120 V AC. The built-in battery is used to buffer the real-time clock and the standard section memory components and is monitored by the CPU. There is a switch to turn the supply volt
-
PSS PS230 2 Bedienungsanleitung Einleitung Diese Bedienungsanleitung gilt für das Netzteil PSS PS230 ab Version 1.3. Übersicht Das Netzteil PS230 stellt die interne Spannung zum Betrieb eines Baugruppenträgers und 12 V DC Versorgungsspannung für die Program- mierung des Anwenderprogrammspeichers zur Verfügung. Es kann wahl- weise mit 230 oder 120 V AC betrieben werden. Die eingebaute Batterie dient zur Pufferung der Echtzeituhr und der Speicherbausteine de
-
PSS PS230 2 Manuel d’utilisation Introduction Ce manuel d’utilisation est valable pour l’alimentation PSS PS230, à partir de la version 1.3. Vue d’ensemble L’alimentation PS230 fournit la tension interne nécessaire au fonctionnement du fond de panier ainsi que la tension d’alimentation 12 V DC pour la programmation de la mémoire du programme utilisateur. Elle peut être utilisée en 230 ou 120 V AC. La batterie installée sert
Questions, Opinions and Exploitation Impressions:
You can ask a question, express your opinion or share our experience of Pilz PSS Series device using right now.
Step 1 – Solve Pilz Pss Error List
Is Pilz Pss Error List appearing? Would you like to safely and quickly eliminate pilz pss 3000 which additionally can lead to a blue screen of death?
When you manually edit your Windows Registry trying to take away the invalid pilz pss 4000 keys you’re taking a authentic chance. Unless you’ve got been adequately trained and experienced you’re in danger of disabling your computer system from working at all. You could bring about irreversible injury to your whole operating system. As very little as just 1 misplaced comma can preserve your Pc from even booting every one of the way by!
Troubleshooting pilz pss 3000 Windows XP, Vista, 7, 8 & 10
Simply because this chance is so higher, we hugely suggest that you make use of a trusted registry cleaner plan like CCleaner (Microsoft Gold Partner Licensed). This system will scan and then fix any Pilz Pss Error List complications.
Registry cleaners automate the entire procedure of finding invalid registry entries and missing file references (including the Pilz error) likewise as any broken hyperlinks inside of your registry.
Issue with pilz pss 3000 handbuch
Backups are made immediately prior to each and every scan providing you with the choice of undoing any changes with just one click. This protects you against doable damaging your pc. Another advantage to these registry cleaners is that repaired registry errors will strengthen the speed and performance of one’s procedure drastically.
- https://www.pilz.com/en-AU/eshop/0010200207700880H2/PSS-3075
- http://www.niwoita.com/pdf/1/pilz-safety-plc-fault-codes.html
- https://www.pilz.com/en-US/eshop/0010200207700880H1/PSS-3047-with-SafetyBUS-p
- https://www.pilz.com/en-GB/eshop/0010200207701280HA/PSS-3000-central-processing-units-with-SafetyBUS-p
Cautionary Note: Yet again, for those who are not an state-of-the-art consumer it’s very encouraged that you simply refrain from editing your Windows Registry manually. If you make even the smallest error within the Registry Editor it can result in you some serious issues that may even call for a brand new set up of Windows. Not all difficulties attributable to incorrect Registry Editor use are solvable.
Fixed: pilz pss 3000 manual
Symptoms of Pilz Pss Error List
“Pilz Pss Error List” appears and crashes the energetic method window.
Your Personal computer routinely crashes with Pilz Pss Error List when running the exact same system.
“Pilz Pss Error List” is shown.
Windows operates sluggishly and responds little by little to mouse or keyboard input.
Your computer periodically “freezes” for the number of seconds in a time.
Will cause of Pilz Pss Error List
Corrupt obtain or incomplete set up of Windows Operating System software program.
Corruption in Windows registry from a new Windows Operating System-related application adjust (install or uninstall).
Virus or malware infection which has corrupted Windows method documents or Windows Operating System-related application data files.
Another method maliciously or mistakenly deleted Windows Operating System-related files.
Mistakes this sort of as “Pilz Pss Error List” can be brought about by several different elements, so it really is important that you troubleshoot every of the achievable brings about to forestall it from recurring.
Simply click the beginning button.
Variety “command” inside the lookup box… Will not hit ENTER nonetheless!
Although keeping CTRL-Shift in your keyboard, hit ENTER.
You’re going to be prompted that has a authorization dialog box.
Click on Of course.
A black box will open having a blinking cursor.
Variety “regedit” and hit ENTER.
Within the Registry Editor, choose the pilz pss 4000 connected key (eg. Windows Operating System) you wish to back again up.
Within the File menu, choose Export.
Inside the Preserve In list, pick out the folder in which you wish to save the Windows Operating System backup key.
Inside the File Title box, sort a reputation for the backup file, these types of as “Windows Operating System Backup”.
From the Export Vary box, ensure that “Selected branch” is selected.
Click on Help you save.
The file is then saved by using a .reg file extension.
You now use a backup within your pilz pss 3000 related registry entry.
Solution to your pilz fault codes problem
There are actually some manual registry editing measures that can not be talked about in this article due to the high chance involved for your laptop or computer method. If you want to understand more then check out the links below.
Additional Measures:
One. Conduct a Thorough Malware Scan
There’s a probability the List Error Pilz Pss error is relevant to some variety of walware infection. These infections are malicious and ready to corrupt or damage and possibly even delete your ActiveX Control Error files. Also, it’s attainable that your Pilz Pss Error List is actually connected to some element of that malicious plan itself.
2. Clean pilz pss 3000 error codes Disk Cleanup
The a lot more you employ your computer the extra it accumulates junk files. This comes from surfing, downloading packages, and any sort of usual computer system use. When you don’t clean the junk out occasionally and keep your program clean, it could turn into clogged and respond slowly. That is when you can encounter an List error because of possible conflicts or from overloading your hard drive.
Once you clean up these types of files using Disk Cleanup it could not just remedy Pilz Pss Error List, but could also create a dramatic change in the computer’s efficiency.
Tip: While ‘Disk Cleanup’ is definitely an excellent built-in tool, it even now will not completely clean up Pilz Pss discovered on your PC. There are numerous programs like Chrome, Firefox, Microsoft Office and more, that cannot be cleaned with ‘Disk Cleanup’.
Since the Disk Cleanup on Windows has its shortcomings it is extremely encouraged that you use a specialized sort of challenging drive cleanup and privacy safety application like CCleaner. This system can clean up your full pc. If you run this plan after each day (it could be set up to run instantly) you are able to be assured that your Pc is generally clean, often operating speedy, and always absolutely free of any List error associated with your temporary files.
How Disk Cleanup can help pilz pss 3056 f-06
1. Click your ‘Start’ Button.
2. Style ‘Command’ into your search box. (no ‘enter’ yet)
3. When holding down in your ‘CTRL-SHIFT’ important go ahead and hit ‘Enter’.
4. You will see a ‘permission dialogue’ box.
5. Click ‘Yes’
6. You will see a black box open up plus a blinking cursor.
7. Variety in ‘cleanmgr’. Hit ‘Enter’.
8. Now Disk Cleanup will start calculating the amount of occupied disk space you will be able to reclaim.
9. Now a ‘Disk Cleanup dialogue box’ seems. There will be a series of checkboxes for you personally to pick. Generally it will likely be the ‘Temporary Files’ that consider up the vast majority of your disk area.
10. Verify the boxes that you want cleaned. Click ‘OK’.
How to repair pss win pro
3. System Restore can also be a worthwhile device if you ever get stuck and just desire to get back to a time when your computer system was working ideal. It will work without affecting your pics, paperwork, or other crucial information. You can discover this option with your User interface.
Pilz Pss
Manufacturer
Device
Operating System
Pilz Pss Error List
4.5 out of
5
based on
39 ratings.
Modular Block System: Emergency Stop Circuits
6-25
The acknowledgements
FbL1 and FbL2 are also monitored in the static
condition. If there are discrepancies between the set and true condition, an
error message will be issued (
ENBL = 0) and the contactors will be
switched off immediately (
K1 = 0 and K2 = 0). The error will need to be
reset.
It is possible to reset errors via the input parameter
RSET both when ON =
0 and when
ON = 1. However, a prerequisite for setting the enable and,
when
ON = 1, switching on the contactors, is that the signals from the
feedback loops are correct.
Error messages
Any fault that is detected will be stored in the corresponding error data
word (
SSNR) of the administration data block (1st data block), until the
fault has been fully dealt with.
• Error messages in the administration data block
— Bit 00:
Fault as the signal changes at input parameter
ON,
feedback loop 1 (
FbL1) remains open
Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter
TFbL and all conditions and
then reset (input parameter
RSET)
— Bit 01:
Fault as the signal changes at input parameter
ON,
feedback loop 1 (
FbL1) remains closed
Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter
TFbL and all conditions and
then reset (input parameter
RSET)
— Bit 02:
Fault as the signal changes at input parameter
ON,
feedback loop 2 (
FbL2) remains open
Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter
TFbL and all conditions and
then reset (input parameter
RSET)
Внимание! Ниже расположена инструкция по умолчанию с возможными решениями проблем, которые могут помочь.
В связи с геополитической ситуацией, для перехода на некоторые сайты может потребоваться VPN.
Запуск от имени администратора и в режиме совместимости
Для начала попробуйте запустить игру от имени администратора. Если игре более 5 лет, попробуйте запустить её в режиме совместимости с более старой версией windows, например windows 7 (для очень старых игр можно попробовать Windows XP SP3).
Правой кнопкой мыши по ярлыку игры → свойства → совместимость → ставим флажки «Запустить программу в режиме совместимости с…» и «Запускать эту программу от имени администратора».
Эти два действия очень часто решают проблему запуска и стабильного ФПС.
Если вы играете через Steam или другой лаунчер, попробуйте запускать игру через него (после того, как выполнили действия выше).
Отключение XMP профиля в Bios
Если вы не знаете, что это такое, то можете переходить к следующему пункту.
Не запускается игра в Steam
Для начала просто перезапустите Steam. Если не помогло, то перейдите в свойства игры → расположение файлов → запуск от имени администратора (смотри самый первый пункт).
Если вы используете пиратку
Есть вероятность, что репак неисправный, подробнее читать тут. Но для начала рекомендуем ознакомиться с пунктами ниже.
Проверка / установка драйверов
Проверьте все драйверы:
- бесплатная утилита Driver Pack (если у вас пустая страница, попробуйте войти через вкладку инкогнито или отключите AdBlock)
- аналог Driver Booster
- зайти на сайт производителя вашего ноутбука или мат. платы и скачать драйвера там
Вы так же можете отдельно установить драйвера на видеокарты и сопутствующее ПО на сайтах разработчиков видеокарт, там драйвера появляются быстрее, чем в автоапдейтерах:
- AMD
- Nvidia
- IntelHD
Обновление DirectX
Все ошибки, которые имеют в себе приставку D3D, X3D, xinput *** .dll скорее всего сообщают об отсутствии нужных библиотек DirectX
- Скачать веб установщик можно здесь
Может помочь установка библиотек NET Framework
- Скачать Microsoft .NET Framework 3.5
- Скачать Microsoft .NET Framework 4
Обновление библиотек Microsoft Visual C++
Если в названии упоминается приставка MSVC, и если не упоминается, обновление этих библиотек для игр чрезвычайно важно. К тому же даже после установки вы можете заметить, что ошибка повторяется, причина в том, что необходимо скачивать все версии, как х64, так и х86, некоторые игры требуют обе.
Распространяемые библиотеки Microsoft Visual C++ скачать
Очистка системы с помощью Advanced SystemCare Free
Скачиваем программу
Запускаем, включаем анализ на основе Искусственного Интеллекта. Программа, вероятно, найдет огромное количество мусорных файлов, битых записей в реестре и прочего.
После завершения анализа примените автоматическое исправление
Системные требования Pillars of Eternity (2015)
Убедитесь, что ваш железный конь соответствует минимальным характеристикам, необходимым для этой игры:
Минимум
Операционная система: Windows Vista или выше (64-bit)
Процессор: Intel Core i3-2100T 2.50 ГГц / AMD Phenom II X3 B73
Видеокарта: ATI Radeon HD 4850 / NVIDIA GeForce 9600 GT
Оперативная память: 4 ГБ
Звуковая карта: совместимая с DirectX
Место на диске: 14 ГБ
Рекомендуется
Операционная система: Windows Vista или выше (64-bit)
Процессор: Intel Core i5-2400 3.10 ГГц / AMD Phenom II X6 1100T
Видеокарта: Radeon HD 7700 / NVIDIA GeForce GTX 570
Оперативная память: 8 ГБ
Звуковая карта: совместимая с DirectX
Место на диске: 14 ГБ
Наличие вирусов
Проверьте ваш компьютер на наличие вирусов, можно использовать бесплатные и пробные версии, например:
- Avast Free Antivirus
- Dr. WEB CureIT
Усердный антивирус блокирует запуск Pillars of Eternity (2015)
Ситуация обратная предыдущей, установленный или встроенный (защитник windows) антивирус блокируют запуск игры, необходимо либо отключить их на время, либо добавить в исключения папку с игрой. Однако, если защитник успел поместить какие-либо файлы в карантин, игру придется переустановить.
Как временно отключить защитник Windows 10
Пуск → Параметры → Обновление и безопасность → Безопасность Windows → Защита от вирусов и угроз → Крутим вниз до пункта «Параметры защиты от вирусов и угроз», кликаем «Управление настройками» → отключаем «Защита в режиме реального времени».
Как добавить файлы и папки в исключения защитника Windows
Пуск → Параметры → Обновление и безопасность → Безопасность Windows → Защита от вирусов и угроз → Крутим вниз до пункта «Исключения», кликаем «Добавление или удаление исключений» → нажимаем «Добавить исключение» → выбираем нужный файл или папку
Pillars of Eternity (2015) изображение выходит за края, изображение не разворачивается на весь экран, неправильное расположение окна игры, проблемы с разрешением экрана
Разумеется, вы уже проверили в настройках игры пункты «разрешение экрана» и «на весь экран».
Проблема может крыться в неправильном масштабировании. Необходимо перейти в свойства ярлыка → изменить параметры высокого DPI → поставить флажок в самом низу и нажать ОК
Pillars of Eternity (2015) неправильно определяет монитор, запускается не на том мониторе
Если вы пытаетесь вывести игру на другой монитор, вам может помочь статья 5 способов вывести игру на второй монитор.
Pillars of Eternity (2015), скачанная с торрента, не работает
Пиратские версии вообще не гарантируют стабильной работы, их разработчики не отвечают перед вами за качество продукта, жаловаться некуда. Есть вероятность, что репак окажется нерабочим, или недоработанным именно под ваши характеристики. В любом случае мы рекомендуем пользоваться лицензионными версиями игр, это убережет ваш компьютер от всевозможных программ-шпионов, майнеров и прочей нечисти, так же обеспечив стабильную поддержку и выход новых патчей от разработчиков.
Pillars of Eternity (2015) не скачивается или скачивается долго. Лагает, высокий пинг, задержка при игре
В первую очередь проверьте скорость своего интернет-соединения на speedtest.net, если заявленная скорость в порядке, проверьте, не загружен ли ваш канал, возможно у вас подключено несколько устройств к вай-фаю, идет обновление операционной системы, скачивается что-то в браузере, или запущен фильм. Посмотрите нагрузку на сеть в диспетчере устройств. Проверьте целостность кабеля, идущего к вашему устройству. Если вы все же пользуетесь торрентом, возможно, скорость раздачи ограничена из-за нехватки раздающих. В крайнем случае вы всегда можете позвонить своему провайдеру и узнать, все ли в порядке с вашей линией.
Pillars of Eternity (2015) выдает ошибку об отсутствии DLL-файла
Запишите название DLL файла и скачайте его, используя интернет поиск, там же должно быть описание, что именно это за файл и где он должен лежать, если никакого описания нет, рекомендуем поискать альтеративные сайты для скачивания. Или воспользуйтесь утилитой DLL-Fixer
Pillars of Eternity (2015) не устанавливается. Установка прекращена, прервана
Проверьте наличие свободного места на вашем диске. Если с местом все в порядке, рекомендуем так же проверить диск на наличие битых секторов с помощью бесплатных программ VictoriaHDD или CrystalDiskInfo
Pillars of Eternity (2015) зависает, застывает изображение
Проблема вполне может быть вызвана самой игрой, это хороший вариант. Но такое поведение может свидетельствовать о неполадках в работе процессора и видеокарты. Проверьте температуры CPU и GPU, нормальный уровень можно узнать на сайте разработчика по модели устройства. Если температура завышена, устройство уже не на гарантии и его давно не чистили, сделайте это сами (если понимаете как) или отнесите в сервисный центр на чистку и замену термопасты, если проблема не устранена, есть вероятность сбоя других компонентов: материнской платы, оперативной памяти или блока питания.
Pillars of Eternity (2015) тормозит. Просадки частоты кадров. Низкий FPS (ФПС)
Вероятно вашему ПК не хватает мощности для стабильной работы Pillars of Eternity (2015). Для начала включите вертикальную синхронизацию, если она выключена и проверьте результат. Затем попробуйте понизить все графические настройки до минимума, кроме разрешения экрана. После повышайте до тех пор, пока картинка остаётся комфортной. Если же понижение не помогло, остаётся только понижать разрешение.
В Pillars of Eternity (2015) нет звука. Ничего не слышно
Проверяем звук в настройках игры. Проверяем звук на самом ПК, например музыку в браузере. Если ничего нет:
- проверьте уровень звука в windows (вашей ОС), возможно уровень звука установлен в 0
- проверьте правильность подключения колонок, наушников
- если устройство нестандартное, ему могут потребоваться свои драйвера от разработчика
- возможно нет драйверов на звук в системе вообще (обновляем, смотри первый пункт)
- в крайнем случае есть вероятность, что вышла из строя звуковая карта
Pillars of Eternity (2015) не видит мышь, клавиатуру или геймпад. Не работает управление
Первым делом перейдите в настройки игры и проверьте, переключено ли у вас устройство управления на геймпад (если проблема в нем). Плотно ли подключены провода? Работают ли устройства вне игры? Решением может быть проверка драйверов с помощью утилит (смотри первый пункт) или банальное отключение → подключение.
Pillars of Eternity (2015) ошибка 0xc0000142
Если Pillars of Eternity (2015) выдает ошибку 0xc0000142, устранить проблему можно одним из способов, указанных ниже. Лучше всего пробуйте один за другим, пока проблема не решится.
- При загрузке игры отлючите все антивирусные программы.
- Проверьте путь к папке игры, все должно быть записано латинскими буквами (английскими). Например C:\Games\Game Folder.
- Имя пользователя Windows тоже должно быть указано латиницей. Нажмите Win+R → наберите команду netplwiz → выделите имя пользователя → Свойства.
- Зайти в свойства игры, кликнув правой кнопкой мыши по ярлыку. Совместимость → Режим совместимости → Выберите режим совместимости отличный от вашей ОС → Поставьте галочку «Запускать от имени администратора«.
Если эти советы не помогли, значит надо искать проблему в стабильности работы ОС и в файлах игры.
- С помощью Advanced SystemCare Free проведите стандартную очистку.
- Замените значение реестра: Поиск → Редактор Реестра → HKEY_LOCAL_MACHINE → SOFTWARE → Microsoft → Windows NT → CurrentVersion → Windows → LoadAppInit_DLLs → в строке Значение замените 1 на 0.
- Проверьте компьютер на наличие вредоносных программ и вирусов. После проверки и чистки перезагрузите ПК и снова загрузите игру.
- Проверьте, чтобы у вас были установленные все необходимые версии компонентов, а именно Microsoft Visual C++, DirectX, Драйвера (смотри пункты в начале).