Ошибка соединения 0x2202 kyocera при сканировании на почту

Good Morning all,

I have had a large influx of users with Kyocera copiers having a 0x2202 scan error on otherwise well working equipment. 0x2202 is typically a network error code. The equipment GUI’s will typically test OK, but users will have intermittent scan failures with the 2202 code. This has been going on/off since Monday, I’ve received 14 calls in total about it, and Kyocera didn’t have much information for fixes. It seems as if Google SMTP server / relay is having intermittent issues.

Edit: I have isolated this specific issue, at this specific point in time to Google only. I haven’t seen a 2202 code for an O365 smtp account this week.

Here’s what I’ve learned:

1. Raise the SMTP timeout on the machine to 120 seconds. This seems to be the fix

2. Have your technician do the latest firmware update on the machine, or at the least, open Device Security -> Network Security -> and enable all TLS and Hash (SHA) protocols for clientside and serverside

3. Login to the SMTP inbox and make sure «Allow less secure apps» is enabled, clear any security prompts, make sure the storage isn’t maxed out, etc.

4. Bonus tip: I haven’t found a correlation yet, but I’ve been removing google DNS from these machines and opting for comcast and cloudflare servers.

I wanted to create this post as there isn’t a ton of information on the web about this error code. I am a Kyocera specific vendor, but most copiers should have similar options to enable/configure.

Cheers… I’ll need one tonight!

Below is a long list of Kyocera error codes.  Some Kyocera printers can be reset by turning the machine power switch off and back on while some others activate “partial operation control” disabling the defective part/area of the machine (paper feed cassette, stapler, document processor etc). If a specific unit is not working, perform U906 after taking measures against the cause of trouble to reactivate the unit.

Error Code
Description

C0030
Fax PWB Problem. Processing with fax software is disabled due to software or hardware issues.

C0060
Main PWB Type Mismatch Error.

C0070
Fax PWB Incompatability Detection Problem. Fax software is not compatible with main PWB software.

C0130
Main PWB EEPROM Backup Memory Device Problem. EEPROM can not be written or read.

C0140
Main PWB EEPROM Backup Memory Data Problem. Abnormal reading data from EEPROM.

C0150
Engine PWB EEPROM Backup Memory Device Problem. EEPROM cannot be written or read.

C0160
Engine PWB EEPROM Backup Memory Data Problem. Abnormal reading data from EEPROM. Read & write data do not match five times consecutively.

C0170
Copy Counts Problem. A checksum error is detected in the main and engine backup memories for copy counters.

C0180
Machine Number Mismatch Error. Machine number does not match on main and engine PWBs

C0600
Main PWB DIMM Installed Incorrectly.

C0610
Main PWB DIMM error

C0630
DMA transmission of compressed, decompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time.

C0640
Hard Disk Drive cannot be accessed

C0700
Optional CF backup is not suitable.

C0800
Image processing problem. JAM05 is detected twice.

C0830
Fax Flash ROM program area checksum error

C0870
Fax PWB to Main PWB high capacity data transfer problem.

C0880
Fax PWB program archive problem.

C0920
Fax backup data is not retained.

C1010
Cassette #1 Lift Motor error. Exceeds 12 seconds of operation or 500ms of overcurrent.

C1020
Cassette #2 Lift Motor error. Exceeds 12 seconds of operation or 500ms of overcurrent.

C1030
PF-700 optional cassette #3 lift motor error.

C1040
PF-700 optional cassette #4 lift motor error.

C1100
PF-750 (Left) Lift Motor 1 error. Exceeds 1 second overcurrent.

C1110
PF-750 (Right) Lift Motor 2 error. Exceeds 1 second overcurrent.

C1120
PF-750 (Left) Lift Motor 1 position problem. PF switch 2 remains off after 30 seconds of motor operation.

C1130
PF-750 (Right) Lift Motor 2 position problem. PF switch 1 remains off after 30 seconds of motor operation.

C1800
PF-700/PF-750 Communication Problem.

C1900
PF-700 EEPROM error. Write data & Read data are not in agreement three times consecutively.

C2000
Drive Motor Problem. Stable Off is detected exceeding 1 sec after motor stability. Stabilization is not detected with 6 sec of activation.

C2250
Main Charge Cleaner Motor error. Lock error is detected three times in a row during cleaner motor operation.

C2500
Paper Feed Motor error. Stable Off is detected exceeding 1 sec after motor stability. Stabilization is not detected within 6 seconds of activation.

C2600
PF-700 Drive Motor error. Lock signal exceeds 500ms.

C2600
PF-750 Paper Conveying Motor error. Lock signal exceeds 450ms.

C3100
Scanner Carriage Problem. Scanner home position is not detected at initialization or start of copying from contact glass.

C3200
Exposure Lamp Problem. Exposure lamp does not reach the input value threshold within 5 sec of commencing reading.

C3210
Exposure Lamp Problem. Exposure lamp does not exceed the input threshold value within 5 sec of commencing reading.

C3300
CCD AGC Problem. After AGC correct input is not obtained at the CCD.

C3310
CIS AGC Problem. After AGC correct input is not obtained at the CIS.

C3500
Communication Error Between Scanner and SHD.

C3900
Scanner PWB Backup Memory Read/Write Problem. Read & Write data does not match.

C3910
Scanner PWB Backup Memory Data Problem. Data in a specified area of the backup memory does not match the specified values.

C4000
Polygon Motor Synchronization Problem. Polygon motor does not stabilize speed within 20 sec of activation.

C4010
Polygon Motor Steady-State Problem. Stable Off is detected for 20 sec continuously after polygon motor stabilization.

C4200
BD Steady-State Problem. ASIC detects a Beam Detect error A for 2 sec after polygon motor stabilization.

C5300
Cleaning Lamp Broken Wire. While the cleaning lamp is On, the broken wire detection signal is detected for 2 sec continuously.

C6000
Fuser Heater Break. Thermistor1 detected less than 70C/158F for 10 sec during warmup & ready. Thermistor2 detected less than 40C/104F for 10 sec during warmup & ready. Temp at thermistor 1or 2 does not rise by at least 1C/1.8F within 5 sec.

C6020
Abnormally High Thermistor Temperature. Thermistor 1 or 2 is detected 250C/482F for 40ms or more.

C6030
Fixing Thermistor Break Error. Thermistor break signal is detected for 1 sec.

C6050
Abnormally Low Thermistor Temperature. Thermistor 1 is detected 80C/176F or less for 1 sec continuously during copying.

C6400
Zero-Cross Signal Error. While fuser heater On/Off control is performed, the zero-cross signal is not input within 3 sec.

C6410
Fuser Unit Connection Insertion Problem. Absence of fuser unit is detected.

C6420
Fuser Unit Fuse Cut Problem. The fuse has been cut 33 sec after the fuse cut signal is turned on.

C7300
Toner Container Problem. Toner level is not detected when toner empty is detected.

C7400
Developing Unit Connection Insertion Problem. Absence of the developing unit is detected.

C7410
Drum Unit Connection Insertion Problem. Absence of the drum unit is detected.

C7800
Broken External Thermistor Wire. Thermistor on the environmental sensor outputs 4.5v or more.

C7810
Short-Circuited External Thermistor. Thermistor input value is 0.5v or less.

C7900
Drum EEPROM Error. Reading or writing to the EEPROM cannot be performed.

C7910
Developing EEPROM Error. Reading or writing to the EEPROM cannot be performed.

C8020
DF-710 Punch Motor Problem. Punch motor lock signal is detected for 500ms or more during activation.

C8030
DF-730 Tray Upper Limit Detection Problem. When tray elevation motor raises a tray, the upper limit switch detects On condition.

C8050
DF-710 Paper Conveying Belt Motor 1 Error. Paper conveying belt home position sensor 1 does not turn Off within 1.5 sec. Paper conveying belt home position sensor 1 does not turn On within 2.5 sec. Jam 88.

C8060
DF-710 Paper Conveying Belt Motor 2 Error. Paper conveying belt home position sensor 2 does not turn Off within 1.5 sec. Paper conveying belt home position sensor 2 does not turn On within 2.5 sec.

C8070
DF-710 Internal Tray Communication Error. The connection is detected, but communication is not possible with the internal tray.

C8140
DF-710 Main Tray Problem. Main tray is not detected in not detected by main tray top limit detection sensor or main tray capacity detection sensor within 20 sec of ascending. Main tray upper limit detection sensor or main tray load detection sensor is not detected as Off within 20 sec of main tray descending. Main tray lower limit detection sensor is not detected as On within 20 sec of main tray descending. Main tray upper limit detection sensor or main tray load detection sensor remain on for 2 sec or more during main tray ascent.

C8140
DF-730 Tray Elevation Motor Problem. Tray lower limit sensor or surface view sensor cannot be detected within 10 sec.

C8170
DF-710 Side Registration Motor 1 Problem. During initial rotations home position is not detected within 3 sec. Jam 88.

C8170
DF-720 Front Side Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the front side home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.

C8170
DF-730 Adjustment Motor Problem. Adjustment motor home position motor is not detected within a specific time during activation.

C8180
DF-710 Side Registration Motor 2 Problem. During initial rotations home position is not detected within 3 sec. Jam 88.

C8180
DF-720 Rear Side Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the rear side home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.

C8190
DF-720 Trailing Edge Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the trailing edge home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.

C8210
DF-710 Stapler Moving Motor 1 Error. During initial rotations home position is not detected within 1.5 sec.

C8210
DF-720 Finisher Stapler Problem. Stapler home position sensor does not change state from non-detect to detect within 200ms of forward (CCW) rotation. During initial rotations stapler home position detection does not change state from non-detect to detect within 600ms of reverse (CW) rotation.

C8210
DF-730 Stapler Problem. Home position is not detected within a specific time of activation.

C8220
DF-710 Stapler Moving Motor 2 Error. During initial rotations home position is not detected within 3.5 sec.

C8230
DF-710 Stapler Motor Problem. Jam 82 is indicated.

C8300
BF-710 Centerfold Unit Communiation Error. Although the connection is detected, communication is not possible with the centerfold unit.

C8310
BF-710 Centerfold Side Registration Motor 1 Problem. During initial rotations home position is not detected within 1000ms.

C8320
BF-710 Centerfold Paper Conveying Belt Motor Problem. During initial rotations home position is not detected within 2500ms.

C8330
BF-710 Blade Motor Problem. During initial rotations home position is not detected within 1500ms.

C8340
BF-710 Centerfold Staple Motor Problem. Jam 89.

C8350
BF-710 Centerfold Side Registration Motor 2 Problem. During initial rotations home position is not detected within 1000ms.

C8360
BF-710 Centerfold Main Motor Problem. The motor lock signal is detected for more than 1000ms during activation.

C8440
DF-730 Sensor Adjusting Problem. The paper entry sensor cannot be adjusted within the specified range.

C8460
DF-730 EEPROM Problem. Reading to or writing from EEPROM cannot be performed.

C8500
MT-710 Communication Error. The connection is detected, but communication is not possible with the mailbox.

C8510
MT-710 Drive Motor Problem. The motor lock signal is detected for more than 500ms during activation.

C8800
DF-710 Communication Problem. No communication: there is no reply after (5) tries. Abnormal communication: a parity or checksum error is detected (5) times in succession.

C8900
DF-710 Backup Memory Data Problem. Read and write data does not match.

C8910
PH-5A Backup Memory Data Problem. Read and write data does not match.

C8920
MT-710 Backup Memory Data Problem. Read and write data does not match.

C8930
BF-710 Backup Memory Data Problem. Read and write data does not match.

C9000
DP-700 Communication Problem. A communication error is detected.

C9040
DP-700 Lift Motor Ascent Error. The DP lift upper limit switch is not detected within 10000 pulses. After a one time retry, the DP lift upper limit switch could not be turned On.

C9050
DP-700 Lift Motor Descent Error. The DP lift lower limit switch is not detected within 10000 pulses. After a one time retry, the DP lift lower limit switch could not be turned On.

C9060
DP-700 EEPROM Error. Read and write data does not match. Data in the specified area of the backup memory does not match the specified values.

C9070
DP-700 Communication Error between the DP and SHD. A communication error is detected.

C9080
DP-700 Communication Error between the DP and CIS. Reading cannot be performed correctly.

CF000
Operation Panel PWB Communication Error/System Error. Unknown error. Communication error between panel and main controller. (If CF620 occurred and is left, CF000 also occurred because of timeout control.

CF010
Main PWB Checksum Error/System Error. Communication error between panel and main controller.

CF020
Memory Checksum Error/Operation System Error.

CF030
Main PWB System Error.

CF040
Engine PWB Communication Error.

CF041
Scanner PWB Communication Error.

CF050
Engine ROM Checksum Error.

CF060
Engine RAM Error.

CF070
Flash ROM Error. Defective flash ROM (which?).

CF080
Flash ROM Error (during download). Defective flash ROM (which?).

CF090
Fax System M Communication Error.

CF14F
Power Source Secondary Side Error/Operation System Error. The operation decomes unstable after recovering the power supply fail (brownout or power drop). Wall voltage is unstable or the main power supply switch was turned OFF/ON within 1 sec.

CF256
Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation.

CF257
Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation.

CF26F
Print System Other Errors. Bug of v.2.03B has been fixed by v. 2.04A (Booklet > Booklet Print).

CF3xx
Undefined.

CF423
Fax System M Error. Wrong data or value detected when the following function is used. Or poor contact at fax card due to mis-installation.

CF423
Fax System M Error. The IF error detects during system authentication from ACT_Account_Manager. Or poor contact at fax card due to mis-installation.

CF433 CF434 CF437 CF43F CF441 CF444 CF445 CF451
HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.

CF45F CF453 CF454 CF45F CF460 CF463 CF46F CF470
HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.

CF473 CF47F CF484 CF487 CF48F CF490 CF493 CF494
HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.

CF5xx
Undefined.

CF610
System Start Error.

CF620
System Error. Error acquiring the event data. Panel detects CF000 as same error.

CF620
System Error. Error acquiring the event data. Panel detects CF000 as same error. Unable to Load Files To CF Card.

CF7D7
Readout Error of SSL (authentication data).

CFAxx
HDD Error.

CFB2C CFB30 CFB31
Panel Error. NetFont error. Communication error between panel and main controller during initialization or rejection of communication by controller during initialization. Blue Screen of Death.

CFB30
Incompatible Level Of Firmware on Main EEPROM.

CFB31
Corrupt Firmware on Main EEPROM.

CFB32
Panel Error. Timeout request for start up command. Start command hasn’t been received. Possible destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death.

CFB33
Panel Error. Detects disconnection with controller. Possible overdrive of control board or destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death.

F000
Operation Panel PWB Communication Error.

F010
Main PWB Checksum Error.

F020
Memory Checksum Error.

F030
Main PWB System Error.

F040
Engine PWB Communication Error.

F041
Scanner PWB Communication Error.

F050
Engine ROM Checksum Error.

F060
Engine RAM Error.

F070
Flash ROM Error.

F080
Flash ROM Error (during download).

F090
Fax Control PWB Communication Error.

F14F
Power Source PWB Second Side Error.

E00000 or U00000
Fax Communication Error: No response or line busy after the set number of redials.

E00100 or U00100
Fax Communication Error: Transmission was interruped by a press of the Stop/Clear key.

E00200 or U00200
Fax Communication Error: Reception was interrupted by a press of the Stop/Clear key.

E00300 or U00300
Fax Communication Error: Recording paper on the destination unit has run out during reception.

E00420 or U00420
Fax Communication Error: A relay request was received from the host center but interrupted because of a mismatch in permit ID or telephone number.

E00421 or U00421
Fax Communication Error: Subaddress-based relay reception was interrupted because of a mismatch in the specified subaddress relay box number.

E00430 or U00430
Fax Communication Error: Polling request (confidential or reverse polling) was received but interrupted because of a mismatch in the permit number.

E00430 or U00430
Fax Communication Error: Subaddress-based bulletin board transmission was interrupted because of a mismatch in the permit ID of the transmitting unit.

E00431 or U00431
Fax Communication Error: Confidential polling transmission was interrupted because the specified confidential box number was not registered.

E00431 or U00431
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because the specified subaddress confidential box was not registered.

E00432 or U00432
Fax Communication Error: Confidential polling transmission was interrupted because of a mismatch in the confidential box ID number.

E00432 or U00432
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because of a mismatch in the subaddress confidential box number.

E00433 or U00433
Fax Communication Error: Confidential polling request was received but data was not present in the confidential box.

E00433 or U00433
Fax Communication Error: Subaddress-based bulletin board transmission request was received but data was not present in the subaddress confidential box.

E00434 or U00434
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box number was intended for encryption.

E00435 or U00435
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box was being accessed.

E00435 or U00435
Fax Communication Error: Subaddress-based bulletin board transmission request was received but interrupted because the specific subaddress confidential box was being accessed.

E00440 or U00440
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was not registered.

E00440 or U00440
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay reception was interrupted because the specific subaddress box was not registered.

E00440 or U00440
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay command reception was interrupted because the specific subaddress box number was being accessed.

E00441 or U00441
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was intended for encryption.

E00450 or U00450
Fax Communication Error: The destination transmitter disconnected because the permit IDs did not agree while the destination transitter is in password-check transmission or restricted transmission.

E00460 or U00460
Fax Communication Error: Encrypted reception was interrupted because the specified encryption box number was not registered.

E00460 or U00460
Fax Communication Error: Ecrypted reception request was received but interrupted because the specified encryption box was being accessed.

E00462 or U00462
Fax Communication Error: Ecryption reception was interrupted because the encryption key for the specified encryption box was not registered.

E00500 or U00500
Fax Communication Error: Multiple communication was interrupted and the call was not made on destination units after interruption.

E00600 or U00600
Fax Communication Error: The document processor cover is open.

E00601 or U00601
Fax Communication Error: Document jam or the document length exceeds the maximum.

E00602 or U00602
Fax Communication Error: Image scanning section problem

E00603 or U00603
Fax Communication Error: No document feed.

E00604 or U00604
Fax Communication Error: Document length exceeded the limit of the bitmap memory capacity.

E00610 or U00610
Fax Communication Error: Recording section cover open.

E00611 or U00611
Fax Communication Error: Recording paper jam.

E00613 or U00613
Fax Communication Error: Image writing section problem.

E00614 or U00614
Fax Communication Error: Nearly empty of recording paper.

E00615 or U00615
Fax Communication Error: Empty of recording paper.

E00620 or U00620
Fax Communication Error: Copier fixing unit problem.

E00622 or U00622
Fax Communication Error: Copier drive motor problem.

E00655 or U00655
Fax Communication Error: CTS was not activated after RTS due to a modem error.

E00656 or U00656
Fax Communication Error: Data was not transmitted after CTS was activated due to a modem error.

E00670 or U00670
Fax Communication Error: Power was cut off during communication.

E00677 or U00677
Fax Communication Error: There was no file to transmit in the memory transmission mode.

E00690 or U00690
Fax Communication Error: System error.

E00700 or U00700
Fax Communication Error: Communication was interrupted because of a problem in the destination unit.

E00800 or U00800
Fax Communication Error: A page transmission error occurred in G3 mode, because of reception of a RTN or PIN signal.

E00810 or U00810
Fax Communication Error: A page transmission error re-occurred in G3 mode after retry of transmission in ECM mode.

E00900 or U00900
Fax Communication Error: A page reception error occurred in G3 mode. An RTN or PIN signal was transmitted because of a page reception error.

E00910 or U00910
Fax Communication Error: A page reception error occurred in G3 mode. A page reception error remained after retry of transmission in ECM mode.

E01000 or U01000
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An FTT signal was received for a set number of times after TCF signal transmissions at 2400bps.

E01000 or U01000
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An RTN signal was received in response to a Q signal (excluding EOP) after transmission at 2400bps.

E01001 or U01001
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The function of the unit differs from that indicated by a DIS signal.

E01010 or U01010
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset number of command retransfers was exceeded (between units of our make).

E01011 or U01011
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DCS, TCF signal, and the preset number of command retransfers was exceeded.

E01012 or U01012
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS1, NSS2 (TCF) signal, and the preset number of command retransfers was exceeded (between units of our make).

E01013 or U01013
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS3, TCF signal, and the preset number of command retransfers was exceeded (between units of our make).

E01014 or U01014
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an MPS signal, and the preset number of command retransfers was exceeded.

E01015 or U01015
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOM signal, and the preset number of command retransfers was exceeded.

E01016 or U01016
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An MCF signal was received but no DIS signal was received after transmission of an EOM signal, and T1 timeout was detected.

E01017 or U01017
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOP signal, and the preset number of command retransfers was exceeded.

E01018 or U01018
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PRI-EOP signal, and the preset number of command retransfers was exceeded.

E01019 or U01019
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CNC signal, and the preset number of command retransfers was exceeded (between units of our make).

E01020 or U01020
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CTC signal, and the preset number of command retransfers was exceeded (ECM).

E01021 or U01021
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOR.Q signal, and the preset number of command retransfers was exceeded (ECM).

E01022 or U01022
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a RR signal, and the preset number of command retransfers was exceeded (ECM).

E01023 or U01023
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PS.NULL signal, and the preset number of command retransfers was exceeded (ECM).

E01024 or U01024
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.MPS signal, and the preset number of command retransfers was exceeded (ECM).

E01025 or U01025
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of command retransfers was exceeded (ECM).

E01026 or U01026
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOP signal, and the preset number of command retransfers was exceeded (ECM).

E01027 or U01027
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.PRI-EOP signal, and the preset number of command retransfers was exceeded (ECM).

E01028 or U01028
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. T5 timeout was detected during ECM Transmission (ECM).

E01040 or U01040
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received during standby for DIS signal reception.

E01041 or U01041
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DNL (MPS or EOM) signal (between units of our make).

E01042 or U01042
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS, TCF signal.

E01043 or U01043
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS1, NSS2 (TCF) signal (between units of our make).

E01044 or U01044
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS3, TCF signal (between units of our make).

E01045 or U01045
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an MPS signal.

E01046 or U01046
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOM signal.

E01047 or U01047
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOP signal.

E01048 or U01048
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PRI-EOP signal.

E01049 or U01049
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CNC signal (between units of our make).

E01050 or U01050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTC signal (ECM).

E01051 or U01051
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an EOR.Q signal (ECM).

E01052 or U01052
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RR signal (ECM).

E01053 or U01053
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.NULL signal (ECM).

E01054 or U01054
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.MPS signal (ECM).

E01055 or U01055
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOM signal (ECM).

E01056 or U01056
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOP signal (ECM).

E01057 or U01057
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.PRI-EOP signal (ECM).

E01070 or U01070
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during handshake.

E01071 or U01071
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during message transmission.

E01072 or U01072
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A break in loop current was detected during transmission.

E01073 or U01073
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the receiver unit, a CM signal was not detected when transmitting after reception.

E01080 or U01080
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A PIP signal was received after transmission of a PPS.NULL signal.

E01091 or U01091
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because a PPR signal was received over (10) times even after reducing the communication speed to the minimum with the symbol speed maintained at the level of connection.

E01092 or U01092
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because of an impossible combination of the symbol speed and communication speed.

E01100 or U01100
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit differs from that indicated by a DCS signal.

E01101 or U01101
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit (excl. communication mode select) differs from that indicated by an NSS signal.

E01102 or U01102
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DTC (NSC) signal was received when no transmission data was in the unit.

E01110 or U01110
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DIS signal.

E01111 or U01111
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DTC (NSC) signal.

E01112 or U01112
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No training reception after reception of a DCS or NSS signal.

E01113 or U01113
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an FTT signal.

E01114 or U01114
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CFR signal.

E01115 or U01115
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an MCF signal.

E01116 or U01116
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a PPR signal.

E01117 or U01117
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CTR signal.

E01118 or U01118
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an ERR signal.

E01119 or U01119
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No further signals were received after reception of a message.

E01120 or U01120
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an MCF signal.

E01121 or U01121
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTP signal.

E01122 or U01122
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTN signal.

E01123 or U01123
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIP signal.

E01124 or U01124
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIN signal.

E01125 or U01125
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a CNS signal (between units of our make).

E01126 or U01126
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PPR signal (ECM).

E01127 or U01127
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an ERR signal (ECM).

E01128 or U01128
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RNR signal (ECM).

E01129 or U01129
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an SPA signal (short protocol).

E01140 or U01140
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DIS signal.

E01141 or U01141
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DTC signal.

E01142 or U01142
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS or NSS signal.

E01143 or U01143
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an FTT signal.

E01144 or U01144
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CFR signal.

E01145 or U01145
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after reception of a message.

E01146 or U01146
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an MCF signal (interoffice communication after reception of an MPS, EOM signal or confidential interoffice communication).

E01147 or U01147
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTP signal.

E01148 or U01148
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTN signal.

E01149 or U01149
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIPsignal.

E01150 or U01150
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIN signal.

E01151 or U01151
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPR signal (ECM).

E01152 or U01152
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTR signal (ECM).

E01153 or U01153
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an ERR signal (ECM).

E01154 or U01154
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an PNP signal (ECM).

E01155 or U01155
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an SPA signal (short protocol).

E01160 or U01160
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During message reception, transmission time exceeded the maximum transmission time per line.

E01161 or U01161
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Number of error lines exceeded limits during message reception.

E01162 or U01162
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A break in loop current was detected during message reception.

E01163 or U01163
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Polarity reversal was detected during message reception.

E01164 or U01164
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. One page length exceeded the specified length during message reception.

E01170 or U01170
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A decoding error occurred during MMR message reception.

E01172 or U01172
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the transmitting unit, a JM signal was not detected after transmission of a CM signal when receiving after transmission.

E01191 or U01191
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Communication was interrupted because an error occurred during an image data reception sequence in the V.34 mode.

E01199 or U01199
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DIS signal with different FIF was received after transmission of a DIS signal.

E01400 or U01400
Fax Communication Error: An invalid one-touch key was specified during communication.

E01500 or U01500
Fax Communication Error: A communication error occurred when calling in V.8 mode.

E01600 or U01600
Fax Communication Error: A communication error occurred when called in V.8 mode.

E01700 or U01700
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol, during transmission in V.34 mode. For example: INFO0/A/Abar (B/Bbar, for polling transmission)/INFOh was not detected.

E01720 or U01720
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol, during transmission in V.34 mode. For example: PPh/ALT/MPh/E was not detected.

E01721 or U01721
Fax Communication Error: A communication error occurred before starting T.30 protocol during transmission in V.34 mode. Operation was interrupted due to the absence of a common communication speed between the units. 1) A DCN signal was received from the destination unit and the line was cut, or 2) a DIS (NSF, CSI) signal was received from the destination unit and in response to the signal, the unit transmitted a DCN signal and the line was cut.

E01800 or U01800
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: INFO0/B/Bbar (A/Abar, for polling reception)/probing tone was not detected.

E01810 or U01810
Fax Communication Error: A communication error occurred in phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: S/Sbar/PP/TRN was not detected.

E01820 or U01820
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol during reception in V.34 mode. For example: PPh/ALT/MPh/E was not detected.

E02000 or U02000
Fax Communication Error: Relay broadcast was refused by a relay station because of a mismatch in permit ID number and permit telephone number when a relay command was used.

E02100 or U02100
Fax Communication Error: A relay command failed because the destination unit (relay station) had no relay broadcast capability.

E02200 or U02200
Fax Communication Error: A relay command from a command station failed because a telephone number was not registered in the relay station was specified.

E02200 or U02200
Fax Communication Error: Relay broadcast was requested to a relay station but failed because a telephone number was not registered in the relay station was specified.

E02200 or U02200
Fax Communication Error: Subaddress-based relay broadcast transmission failed because the data registered in the subaddress relay box was deleted.

E02303 or U02303
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. Timeout was detected before a correct DNL signal was received.

E02304 or U02304
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. A signal other than MPS or EOM signal was received after a DNL signal was received.

E02400 or U02400
Fax Communication Error: An interoffice subaddress-based relay transmission was interrupted because of a mismatch in the specified relay box number.

E03000 or U03000
Fax Communication Error: No document was present in the destination unit when polling reception started.

E03100 or U03100
Fax Communication Error: In reverse polling, although no original was set in the destination unit, transmission was complete.

E03200 or U03200
Fax Communication Error: In confidential polling reception, data was not accumulated in the specified box in the destination unit.

E03200 or U03200
Fax Communication Error: In interoffice subaddress-based bulletin board reception, data was not stored in the box specified by the destination unit.

E03300 or U03300
Fax Communication Error: In polling reception from a unit of our make, operation was interrupted due to a mismatch in permit ID number or telephone number.

E03300 or U03300
Fax Communication Error: In interoffice subaddress-based bulletin board reception, operation was interrupted due to a mismatch in permit ID number or telephone number.

E03400 or U03400
Fax Communication Error: Polling reception was interupted because of a mismatch in individual numbers.

E03500 or U03500
Fax Communication Error: In confidential polling reception, the specified confidential box number was not registered in the destination.

E03500 or U03500
Fax Communication Error: In interoffice subaddress-based bulletin board reception, the specified subaddress confidential box number was not registered in the destination unit.

E03500 or U03500
Fax Communication Error: The destination was being accessed.

E03600 or U03600
Fax Communication Error: Confidential polling reception was interrupted because of a mismatch in specified confidential box numbers.

E03600 or U03600
Fax Communication Error: An interoffice subaddress-based bulletin board reception was interrupted because of a mismatch in the specified subaddress confidential box number.

E03700 or U03700
Fax Communication Error: Confidential polling reception failed because the destination unit had no confidential polling transmission capability or data was not accumulated in any box in the destination unit.

E03700 or U03700
Fax Communication Error: Interoffice subaddress-based bulletin board reception failed because the destination unit had no subaddress-based bulletin board transmission capability, or data was not stored in any subaddress confidental box in the destination unit.

E04000 or U04000
Fax Communication Error: The confidential box specified for confidential transmission was not registered in the destination unit.

E04000 or U04000
Fax Communication Error: In interoffice subaddress-based transmission mode, the specified subaddress box number was not registered in the destination unit.

E04000 or U04000
Fax Communication Error: The destination was being accessed.

E04100 or U04100
Fax Communication Error: Confidential transmission failed because the destination unit had no confidential capability.

E04100 or U04100
Fax Communication Error: Subaddress-based transmission failed because the destination unit had no subaddress-based reception capability.

E04200 or U04200
Fax Communication Error: In encrypted tranmission, the specified encryption box was not registered in the destination unit.

E04300 or U04300
Fax Communication Error: Encrypted transmission failed because the destination unit had no encrypted communication capability.

E04400 or U04400
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted transmission. Encryption keys did not agree.

E04401 or U04401
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted trasmission. The encryption key was not registered.

E04500 or U04500
Fax Communication Error: Encrypted reception was interrupted because of a mismatch in ecryption keys.

E05000 or U05000
Fax Communication Error: In transmission with a specified number, the set number of originals was different from the number of transmitted originals.

E05100 or U05100
Fax Communication Error: Password check transmission or restricted transmission was interrupted because the permit ID numbers did not match.

E05200 or U05200
Fax Communication Error: Password check reception or restricted reception was interrupted because the permit ID numbers did not match, the rejected fax numbers did match, or the destination receiver did not return its phone number.

E05300 or U05300
Fax Communication Error: Password check reception or restricted reception was interrupted because the permitted numbers did not match, the rejected numbers did match, or the machine in question did not acknowledge its phone number.

E09000 or U09000
Fax Communication Error: G3 communication was attempted but failed because the destination unit was a G2 machine.

E12000 or U12000
Fax Communication Error: Relay broadcast was requested from a command station but memory overflowed during reception.

E12000 or U12000
Fax Communication Error: In subaddress-based relay reception memory overflowed.

E12100 or U12100
Fax Communication Error: Relay was commanded but memory overflowed in the destination unit (relay station).

E14000 or U14000
Fax Communication Error: Memory overflowed during confidential reception.

E14000 or U14000
Fax Communication Error: Memory overflowed in subaddress-based confidential reception.

E14100 or U14100
Fax Communication Error: Memory overflowed in the destination unit during confidential transmission.

E14100 or U14100
Fax Communication Error: Memory overflowed in the destination unit during interoffice subaddress-based transmission.

E19000 or U19000
Fax Communication Error: Memory overflowed during memory reception.

E19100 or U19100
Fax Communication Error: Memory overflowed in the destination unit during transmission.

E19200 or U19200
Fax Communication Error: Memory transmission failed because a decoding error occurred.

E19300 or U19300
Fax Communication Error: Transmission failed because an error occurred during JBIG encoding.

E19400 or U19400
Fax Communication Error: Reception failed because an error occurred during JBIG encoding.

Send SMB Error 1102
Error: Username/Password or Shared Name/Folder Name. Domain name is not entered.

Send SMB Error 1102
Error: Username/Password or Shared Name/Folder Name. Assign disable user/password.

Send SMB Error 1102
Error: Username/Password or Shared Name/Folder Name. Assign the user who is not allowed to access the folder.

Send SMB Error 1102
Error: Username/Password or Shared Name/Folder Name. Assign disable shared name.

Send SMB Error 1102
Error: Username/Password or Shared Name/Folder Name. Host name error.

Send SMB Error 1103
Error: Pathname or File Name. Domain name is not entered.

Send SMB Error 1103
Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.

Send SMB Error 1103
Error: Pathname or File Name. Assign disable folder path.

Send SMB Error 1105
Error: Not Supported Protocol. SMB protocol is set to OFF.

Send SMB Error 2101
Error: Can Not Connect. Enter the disable host name/IP address.

Send SMB Error 2101
Error: Can Not Connect. Assign the wrong port number.

Send SMB Error 2101
Error: Can Not Connect. Network is not connected.

Send SMB Error 2103
Error: Response Wait With Timeout. The server is unable to communicate.

Send SMB Error 2201
Error: Network Transfer. Error occurs on the network.

Send SMB Error 2203
Error: Response Wait With Timeout. Response is not returned from the server, above specified time.

Send SMB Error 9181
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.

Send FTP Error 1101
Error: Host Name. Enter the disable host name/IP address.

Send FTP Error 1102
Error: Username/Password. Domain name is not entered.

Send FTP Error 1102
Error: Username/Password. Assign disable user/password.

Send FTP Error 1103
Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.

Send FTP Error 1103
Error: Pathname or File Name. Assign disable folder path.

Send FTP Error 1105
Error: Not Supported Protocol. FTP protocol is set to OFF.

Send FTP Error 2101
Error: Can Not Connect. Enter the disable host name/IP address.

Send FTP Error 2101
Error: Can Not Connect. Assign the wrong port number.

Send FTP Error 2101
Error: Can Not Connect. Network is not connected.

Send FTP Error 2102
Error: Cannot Connect With Timeout. The server is unable to communicate.

Send FTP Error 2102
Error: Cannot Connect With Timeout. Send the server which does not support FTP server.

Send FTP Error 2103
Error: Response Wait With Timeout. The server is unable to communicate.

Send FTP Error 2201
Error: Network Transfer. Error occurs on the network.

Send FTP Error 2202
Error: Network Transfer With Timeout. Error occurs on the network.

Send FTP Error 2203
Error: Response Wait With Timeout. Response is not returned from the server, above specified time.

Send FTP Error 3101
Error: Server Response. The server is error status.

Send FTP Error 9181
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.

Send email Error 1101
Error: Host Name. SMTP server name is not set. Error SMTP server name.

Send email Error 1102
Error: Username/Password. User ID for the authentication is not entered or entered wrongly. Wrong authentication password is entered.

Send email Error 1104
Error: No Recipient Address. The destination address is not specified.

Send email Error 1105
Error: Not Supported Protocol. SMTP protocol is set to OFF.

Send email Error 1106
Error: No Sender Info. Sender address is not entered.

Send email Error 2101
Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP.

Send email Error 2101
Error: Can Not Connect. The specified server is not SMTP server.

Send email Error 2101
Error: Can Not Connect. Network is not connected.

Send email Error 2102
Error: Cannot Connect With Timeout. The server is unable to communicate.

Send email Error 2103
Error: Response Wait With Timeout. The server is unable to communicate.

Send email Error 2201
Error: Network Transfer. Error occurs on the network.

Send email Error 2202
Error: Network Transfer With Timeout. Error occurs on the network.

Send email Error 2203
Error: Response Wait With Timeout. Response is not returned from the server, above specified time.

Send email Error 2204
Error: Email Size Limit. The size of the email attachment exceeds its limit.

Send email Error 3101
Error: Server Response. The server is error status.

Send email Error 3101
Error: Server Response. Server setting is not authenticated normally.

Send email Error 3201
Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism is found.

Send email Error 9181
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.

TWAIN Error 2202
Error: Network Transfer With Timeout. Response is not returned from the server, above the specified time.

TWAIN Error 9181
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.

Software Error 5101
Error: Not Yet Connected. Operation handle error. Error for stored status in the operation handle.

Software Error 5102
Error: Already Connected. Operation handle error. Error for stored status in the operation handle.

Software Error 5103
Error: Not Yet Opened. Error for storage status in the operation handle.

Software Error 5104
Error: Already Opened. Error for storage status in the operation handle.

Software Error 7101
Error: Memory Allocation. Insufficient memory space.

Software Error 7102
Error: Socket Create. Unable to create a communication socket.

Software Error 720f
Error: Unknown Error. Unable to determine the cause.

Send error. Job is cancelled. Press [End]. 1101
Send Email Error: Host Name. SMTP server name is not set. Error SMTP server name.

Send error. Job is cancelled. Press [End]. 1101
Send FTP Error: Host Name. Enter the disable host name/IP address.

Send error. Job is cancelled. Press [End]. 1102
Send Email Error: Username/Password. User ID for the authentication is not entered or entered wrongly. Wrong authentication password is entered.

Send error. Job is cancelled. Press [End]. 1102
Send SMB/FTP Error: Username/Password or Shared Name/Folder Name. Domain name is not entered.

Send error. Job is cancelled. Press [End]. 1102
Send SMB/FTP Error: Username/Password or Shared Name/Folder Name. Assign disable user/password.

Send error. Job is cancelled. Press [End]. 1102
Send SMB Error: Username/Password or Shared Name/Folder Name. Assign disable shared name.

Send error. Job is cancelled. Press [End]. 1102
Send SMB Error: Username/Password or Shared Name/Folder Name. Host name error.

Send error. Job is cancelled. Press [End]. 1103
Send SMB/FTP Error: Pathname or File Name. Domain name is not entered.

Send error. Job is cancelled. Press [End]. 1103
Send SMB/FTP Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.

Send error. Job is cancelled. Press [End]. 1103
Send SMB/FTP Error: Pathname or File Name. Assign disable folder path.

Send error. Job is cancelled. Press [End]. 1104
Send Email Error: No Recipient Address. The destination address is not specified.

Send error. Job is cancelled. Press [End]. 1105
Send Email Error: Not Supported Protocol. SMTP protocol is set to OFF.

Send error. Job is cancelled. Press [End]. 1105
Send SMB Error: Not Supported Protocol. SMB protocol is set to OFF.

Send error. Job is cancelled. Press [End]. 1105
Send FTP Error: Not Supported Protocol. FTP protocol is set to OFF.

Send error. Job is cancelled. Press [End]. 1106
Send Email Error: No Sender Info. Sender address is not entered.

Send error. Job is cancelled. Press [End]. 2101
Send Email Error: Can Not Connect. Network is not connected.

Send error. Job is cancelled. Press [End]. 2101
Send Email Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP.

Send error. Job is cancelled. Press [End]. 2101
Send Email Error: Can Not Connect. The specified server is not SMTP server.

Send error. Job is cancelled. Press [End]. 2101
Send SMB/FTP Error: Can Not Connect. Enter the disable host name/IP address.

Send error. Job is cancelled. Press [End]. 2101
Send SMB/FTP Error: Can Not Connect. Assign the wrong port number.

Send error. Job is cancelled. Press [End]. 2101
Send SMB/FTP Error: Can Not Connect. Network is not connected.

Send error. Job is cancelled. Press [End]. 2102
Send Email/ FTP Error: Cannot Connect With Timeout. The server is unable to communicate.

Send error. Job is cancelled. Press [End]. 2102
Send FTP Error: Cannot Connect With Timeout. Send the server which does not support FTP server.

Send error. Job is cancelled. Press [End]. 2103
Send Email/ SMB/ FTP Error: Response Wait With Timeout. The server is unable to communicate.

Send error. Job is cancelled. Press [End]. 2201
Send Email/ SMB/ FTP Error: Network Transfer. Error occurs on the network.

Send error. Job is cancelled. Press [End]. 2202
Send Email/FTP Error: Network Transfer With Timeout. Error occurs on the network.

Send error. Job is cancelled. Press [End]. 2202
Send TWAIN Error: Network Transfer With Timeout. Response is not returned from the server, above the specified time.

Send error. Job is cancelled. Press [End]. 2203
Send Email/FTP Error: Response Wait With Timeout. Response is not returned from the server, above specified time.

Send error. Job is cancelled. Press [End]. 2204
Send Email Error: Email Size Limit. The size of the email attachment exceeds its limit.

Send error. Job is cancelled. Press [End]. 3101
Send Email/FTP Error: Server Response. The server is error status.

Send error. Job is cancelled. Press [End]. 3101
Send Email Error: Server Response. Server setting is not authenticated normally.

Send error. Job is cancelled. Press [End]. 3201
Send Email Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism is found.

Send error. Job is cancelled. Press [End]. 5101
Send Software Error: Not Yet Connected. Operation handle error. Error for stored status in the operation handle.

Send error. Job is cancelled. Press [End]. 5102
Send Software Error: Already Connected. Operation handle error. Error for stored status in the operation handle.

Send error. Job is cancelled. Press [End]. 5103
Send SoftwareError: Not Yet Opened. Error for storage status in the operation handle.

Send error. Job is cancelled. Press [End]. 5104
Send Software Error: Already Opened. Error for storage status in the operation handle.

Send error. Job is cancelled. Press [End]. 7102
Send Software Error: Socket Create. Unable to create a communication socket.

Send error. Job is cancelled. Press [End]. 720f
Send Software Error: Unknown Error. Unable to determine the cause.

Send error. Job is cancelled. Press [End]. 9181
Send Email/ SMB/ FTP/ TWAIN Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.

«Acceptable staple count exceeded.»
Is the acceptable staple count exceeded?

«Add paper in cassette #.»
Is the indicated cassette out of paper?

«Add paper in MP tray.»
Is the paper of the specified size loaded in the multipurpose tray?

«Add staples.»
Has the document finisher run out of staples?

«Add toner.»
 

«An error has occurred.»
An internal error has occurred.Make a note of the error code number displayed on the panel. See above.

«Box Limit Exceeded.»
Document Box is full, and no further storage is available; Job is cancelled. Repeat Copy Box is full, and no further repeat copy is available.

«Cannot connect to Authentication Server.»
 

«Cannot duplex print on this paper.»
Did you select a paper size/type that cannot be duplex printed?

«Cannot execute this job.»
Job is restricted by Job Accounting.

«Cannot offset this paper.»
Did you select a paper size that cannot be offset (A3, B4, A5R, B6R, Folio, Ledger, Statement, & 8K)?

«Cannot punch this paper type.»
Did you select a paper size/type that cannot be punched?

«Cannot staple this paper.»
Did you select a paper size/type that cannot be stapled?

«Check the cover.»
Are any covers open? Does the message indicate which cover is open?

«Check the document processor.»
Is the document processor open? Is the top cover of the document processor open?

«Check the finisher.»
Is the document finisher set correctly?»

«Clean the slit glass.»
Dirt has been identified on the slit glass.

«Empty the punch waste box.»
The punch waste box of the 3,000 sheet finisher is full.

«Failed to specify Job Accounting.»
Job accounting is not specified in the print driver.

«Failed to store job retention data.»
 

«Fax box limit exceeded.»
Fax box is full, and no further storage is available.

«Finisher tray is full of paper.»
Is the acceptable storage capacity exceeded for the document finisher tray?»

«Folding tray is full of paper.»
Is the acceptable storage capacity exceeded for the folding tray of the 3,000 sheet document finisher?»

«Hard Disk error. Job is cancelled. Press [End] ##»
An error has occurred on the hard disk.

«Incorrect Login User Name or Password.»
 

«Job Accounting restriction exceeded.»
The print count exceeded the acceptable count restricted by Job Accounting.

«Job Separator is full of paper.»
Is the maximum capacity of the job separator tray exceeded?

«KPDL error.»
A PostScript error has occurred.

«Mailbox tray is full of paper.»
 

«Memory card error.»
Was the memory card (Compact Flash) removed while being accessed? Was a valid memory card inserted?

«Memory card error. Job is cancelled. Press [End]. Code: 01
Memory Card Error: Format error.

«Memory card error. Job is cancelled. Press [End]. Code: 04
Memory Card Error: Insufficient memory card space to complete this operation.

«Memory is full.»
Unable to continue the job, as the memory is used up.»

«Memory Is Low»
Logic Lockup

«Paper Jam. ###»
Make a note of the jam location number displayed on the panel. Leave the machine On.

«Print overrun.»
Warning. Low printer memory.

«Removable memory error.»
An error has occurred on the USB stick memory or Compact Flash memory.

«Removable memory was removed.»
 

«Replace all originals and press [Continue].»
 

«Replace the waste toner box.»
The waste toner box is full.

«Reset all originals in the document processor.»
Are there any originals left in the document processor?

«Scanner memory is full.»
Scanning cannot be performed due to insufficient memory for the scanner. Is the acceptable scanning count exceeded?

«Scanner Paused»
DMA transmission of compressed, ecompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time.

«Set the folding tray.»
Is the folding tray correctly installed to the 3,000 sheet capacity document finisher?

«Set the folding unit.»
Is the folding tray correctly installed to the 3,000 sheet capacity document finisher?

«Set the punch waste box.»
The waste toner box is not installed correctly.

«Set the waste toner box.»
The waste toner box is not installed correctly.

«Staple error.»
The location of the jam will be indicated on the panel. Leave the machine On.

«Staple jam.»
The location of the jam will be indicated on the panel. Leave the machine On.

«The ID is not registered.»
The account ID# does not match.

«The memory card is not formatted.»
Is the removable memory formatted by this machine?

«The phone receiver is off the hook.»
 

«The removable memory is not formatted.»
Is the removable memory formatted by this machine?

«The source file is not found.»
The specified file is not found.

«Top tray of the machine is full of paper.»
The exit tray at the top of the machine is full.

«Tray # is full of paper.»
Is the acceptable storage capacity exceeded for any of the output trays A, B, or C of the 3,000 sheet capacity document finisher?

«Warning low memory.»
Further scanning cannot be performed due to insufficient memory.

Error Code
Description

0xF330
Component: RIP. Category: RIP. Recovery impossible error (CreatePrint and return back value of API is indirect).

0xF331
Component: RIP. Category: RIP. Fail to initialize.

0xF333
Component: RIP. Category: RIP. Access failure to ME.

0xF335
Component: RIP. Category: RIP. Failure to switch TASK.

0xF336
Component: RIP. Category: RIP. IOBL process failure.

0xFB30
Component: Panel. Category: KI-Panel. Failed to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode.

0xFB31
Component: Panel. Category: KI-Panel. Refused to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode.

0xFB32
Component: Panel. Category: KI-Panel. Time to start up request command (start up request command could not be received). Blue back screen. Cannot enter maintenance mode.

0xFB33
Component: Panel. Category: KI-Panel. Cut off of the communication with the controller is detected — waiting to receive: select () OK return, recv() RX data length 0. Blue back screen. Cannot enter maintenance mode.

0xFB34
Component: Panel. Category: KI-Panel. Time out for Response telegraphic message (could not receive response telegraphic message within a fixed time). In case on not through httpd, this error occurs (in case it does not become CGI time out).

0xFB35
Component: Panel. Category: KI-Panel. Received abusive command from controller. At this moment, only the case that unexpected command comes in when wating for the startup request command.

0xFB36
Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. select () function returned the error (other than EINTR).

0xFB37
Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. rcv () function returned the error.

0xFB38
Component: Panel. Category: KI-Panel. Communication error is detected when transferring (using UNIX domain) response telegraphic message in the panel. send() function returned the error (other than EINTR).

0xFB39
Component: Panel. Category: KI-Panel. Crucial error is detected when processing receive/transfer of the response telegraphic message from controller. Failed to acquire semafo???

0xFB3A
Component: Panel. Category: KI-Panel. Communication error is detected when sending required response telegraphic message from panel. send() function returned the error (other than EINTR).

CF000
Component: HDD. Failure to initialize with «dbinit, hostif_stat_chg» comand.

CF000
Operation panel PWB comunication error.

CF010
ROM Checksum Error.

CF010
Main PWB Checksum Error/System Error. Communication error between panel and main controller.

CF012
ROM Checksum Error.

CF020
Memory Checksum Error/Operation System Error.

CF030
Main PWB System Error.

CF040
Engine PWB Communication Error.

CF040
Engine PWB Communication Error.

CF041
Scanner PWB Communication Error.

CF050
Engine ROM Checksum Error.

CF060
Engine RAM Error.

CF070
Flash ROM Error. Defective flash ROM (which?).

CF080
Flash ROM Error (during download). Defective flash ROM (which?).

CF090
Fax System M Communication Error.

CF125
Scanner Unit Error

CF131
Component: PCM. Category: OS. Failure to initialize with «dbinit, hostif_stat_chg» comand.

CF131
Component: PCM. Category: OS. Failure to acquire Entity data with «dbinit, hostif_stat_chg» comand.

CF145
Fax Unit Error.

CF14F
Power Source Secondary Side Error/Operation System Error. The operation decomes unstable after recovering the power supply fail (brownout or power drop). Wall voltage is unstable or the main power supply switch was turned OFF/ON within 1 sec.

CF14F
Component: OS. Category: OS. Primary supply voltage dropped off temporarily and recovery operation was not stable. If the input power supply voltage is not stable of the Main SW is turned Off/On quickly (about 1 second), this problem occurs.

CF186
Print Unit: DVU_PRT_SYSERR_F226_ERROR (Video data flushing error)

CF18A
Engine Firmware Incompatible.

CF18C
Document BOX error.

CF1FF
Component: ScanSys. Category: ScanSys. When the scanner scanning parameter from the topside is in error.

CF1FF
Component: IPLogical. Category: PrintSystem. Could not obtain instance of Config, SystemStatus. Use below mentioned class: ipl_search_output.cpp, ipl_feeder_spec.cpp, outputcheck.cpp.

CF1FF
Component: Machine Configuration. Category: PrintSystem. Could not obtain instance of Config, SystemStatus. Use below mentioned class: machine_status_engine.cpp.

CF1FF
Component: OutputMission. Category: PrintSystem. Increasing and decreasing «Lib», in case that even if there is no original available, tried to process increasing & decreasing.

CF1FF
Component: OutputMission. Category: PrintSystem. In case to specify some other value (indirect value) other than single sided/duplex/forced duplex for increasing & decreasing «Lib».

CF1FF
Component: OutputMission. Category: PrintSystem. In case of the address for Job setting value structure is NULL.

CF1FF
Component: OutputMission. Category: PrintSystem. In case of the code for output completion notice is indirect.

CF1FF
Component: OutputMission. Category: PrintSystem. When writing the original information to the storage, in case to get the reply back as [Other Error].

CF1FF
Component: OutputMission. Category: PrintSystem. In case to get the reply as [Finisher out of order Error], [No Feeder available in search] from Paper feed/eject «Lib».

CF1FF
Component: OutputMission. Category: PrintSystem. In case to get the reply as failure from rotation calculation «Lib».

CF1FF
Component: PrintSystem. Category: PrintSystem. Could not obtain instance of Config, SystemStatus. Use below mentioned class: print_startup.cpp.

CF1FF
Component: SVI. Category: LioPanel. Logical Error (In case of given parameter is NULL).

CF214
Codec: GICL_CDC_ERR_FACTOR_JPEG (several hardware error, software error).

CF215
Codec: GICL_CDC_ERR_FACTOR_SRLE (several hardware error, software error).

CF234
Data conversion error.

CF235
Error code when receiving/printing email.

CF245
Process Manager: SYS_PRCM_ERR_FACTOR_SVC_PROC_DOWN (Device process down).

CF246
Process Manager: SYS_PRCM_ERR_FACTOR_DEV_PROC_DOWN (Device process down).

CF247
Process Manager: SYS_PRCM_ERR_FACTOR_JOBIMG_PROC_DOWN (Job image process down).

CF247
Component: ScanSys. Category: ScanSys. Library Error inside of ScanSys.

CF248
Component: UNKNOWN. Category: UNKNOWN.

CF248
Component: UNKNOWN. Category: UNKNOWN. Code present on with Kyocera Barfode Font CF card installed.

CF248
Process Manager: SYS_PRCM_ERR_FACTOR_PRN_PROC_DOWN (Printer process down).

CF256
Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation.

CF257
Component: LFM. Category: FaxSys. KUIOLIB error. Poor contact at the fax card card due to mis-installation.

CF257
Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation.

CF25E
Network Manager:

CF25F
Component: LFM. Category: FaxSys. Instance Check Error, Paramemter Error from topside.

CF26F
Component: PrintSys. Category: PrintSys. It occurs when the error noticed from VideoDriver. Use by Video_Driver class: Function name, factor can be found by the detail code.

CF26F
Print System Other Errors. Bug of v.2.03B has been fixed by v. 2.04A (Booklet > Booklet Print).

CF26F
System State Manager:

CF278
Energy Saving Manager:

CF320
Component: LioFax. Category: FaxSys. An Observer Deletion Error occurred during salvage process. Error received from the method on EventManager or message Tx.

CF321
Component: LioFax. Category: FaxSys. Segment code for LioFax initialization is different from «03KH».

CF323
Component: LioFax. Category: FaxSys. Return address of Page class when doing FAX Tx/Rx is other abnormal error. Entity (Config, BOX, etc.) access error.

CF324
Component: LioFax. Category: FaxSys. Entity parameter error.

CF325
Component: LioFax. Category: FaxSys. In case that the time when Error came back from LFM.

CF326
Component: LioFax. Category: FaxSys. IOBL error.

CF327
Component: LioFax. Category: FaxSys. At the time of KUIOLIB error, CodeChange error, FaxLib error (Sender recorde, Entity related error).

CF32F
Component: LioFax. Category: FaxSys. Instance Check Error. Parameter Error from topside.

CF337
Device Error (scan control):

CF3FF
Component: RIP. Category: RIP. Other/System Crucial Error.

CF423
Component: FaxJOB. Category: FaxSys. As the error came back at IF for DocumentBox, JobInfo, Config Entity.

CF423
Component: FaxJob. Category: FaxSys. The error came back when accessing (obtaining data, setting data) to below Entity related: job_ent(JobModel,JobInfo), config_ent, reservation, account(certificate), document_box.

CF423
Fax System M Error. Wrong data or value detected when the following function is used. Or poor contact at fax card due to mis-installation.

CF423
Fax System M Error. The IF error detects during system authentication from ACT_Account_Manager. Or poor contact at fax card due to mis-installation.

CF424
Component: FaxJob. Category: FaxSys. As the error came back when obtaining IF for system authentication from ACT_Account_Manager.

CF424
Component: FaxJob. Category: FaxSys. The date obtained from the below Entity related is unexpected data: job_ent(JobInfo).

CF427
Component: FaxJob. Category: FaxSys. The error came back for the IF of LioFax observer addition/deletion.

CF42F
Component: FaxJob. Category: FaxSys. As handing over of the NULL pointer in the class occurred. As memory reservation with new in heap domain is failed: Assert for preventing from segment drop off.

CF42F
Component: FaxJob. Category: FaxSys. When generating the class, fail new at obtaining data domain, soft logic error (software bug).

CF433
Component: NetClient. Category: ImageProcess. Entity Error.

CF434
Component: NetClient. Category: ImageProcess. Entity Data Invalid.

CF437
Component: NetClient. Category: ImageProcess. Other Library Error (ImageLibrary, PageData, EventManager).

CF43F
Component: NetClient. Category: ImageProcess. Crucial (no memory, invalid parameter, etc.).

CF441
Component: CreateScan. Category: ImageProcess. Initialize Error.

CF444
Component: CreateScan. Category: ImageProcess. Entity Data Invalid.

CF445
Component: CreateScan. Category: ImageProcess. Middleware Error (LioScanner error).

CF451
Component: CreatePrint. Category: ImageProcess. Initialization Error.

CF433 CF434 CF437 CF43F CF441 CF444 CF445 CF451
HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.

CF453
Component: CreatePrint. Category: ImageProcess. Entity Error.

CF454
Component: CreatePrint. Category: ImageProcess. Entity Data Mismatch.

CF45F
Component: CreatePrint. Category: ImageProcess. Other Error.

CF460
Component: CreateBox (Memory Tx). Category: ImageProcess. Unrecoverable Error.

CF463
Component: CreateBox (Memory Tx). Category: ImageProcess. Entity Error.

CF46F
Component: CreateBox (Memory Tx). Category: ImageProcess. Crucial (no memory, invalid parameter, etc.).

CF46F
PDL Interpreter: REN_INT_ERR_FACTOR_GENERAL (other general error).

CF470
Component: CreateFax. Category: ImageProcess. Unrecoverable Error.

CF473
Component: CreateFax. Category: ImageProcess. Entity Error.

CF47F
Component: CreateFax. Category: ImageProcess. Crucial (no memory, invalid parameter, etc.).

CF484
Component: Edit. Category: ImageProcess. Data Invalid (PageData).

CF487
Component: Edit. Category: ImageProcess. Other Library Error (ImageLibrary).

CF48F
Component: Edit. Category: ImageProcess. Crucial.

CF490
Component: Output(Fax). Category: ImageProcess. Unrecoverable Error.

CF493
Component: Output(Fax). Category: ImageProcess. Entity Error.

CF494
Component: Output(Fax). Category: ImageProcess. Entity Data Invalid.

CF45F CF453 CF454 CF45F CF460 CF463 CF46F CF470 CF473 CF47F CF484 CF487 CF48F CF490 CF493 CF494
HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.

CF515
 

CF526
System Error:

CF528
Component: SVI. Category: LioPanel. Panel data abusion error.

CF530
Component: PJL. Category: RIP. Recovery impossible error: Thread Create failed.

CF530
Component: ReportEventService. Category: RIP. Recovery impossible error: Thread Create failed.

CF530
Component: SVCTL_FaxRx_Event_Control. Category: KI Sc. As failed to obtain EM_FaxRx_Ec_Event_Fax_Enable.

CF530
Component: SVCTL_Reservation_Event_Control. Category: KI Sc. As failed to notice the event for EM_Rsv_EC_op_Event_FaxJob_Ready.

CF530
Component: SVCTL_Job_Start_Command. As JobInfo giving to JSM_JobServiceManager is NULL.

CF533
Component: PJL. Category: RIP. Entity error: when CLITICAL ERROR occurred at ME access.

CF533
Component: ReportEventService. Category: RIP. Entity error: when CLITICAL ERROR occurred at ME access.

CF551
Component: MLPRN. Category: NetAppl. Task generation error.

CF551
Component: MLPRT. Category: NetAppl. Task generation error.

CF551
Component: EVR_LGS. Category: NetAppl. Task generation error.

CF610
Component: SSTUP. Category: OS. Error in the SystemStartUp (Thread generation, Entity data acquisition, DiskManager operation).

CF610
Undefined.

CF610
System Start Error.

CF615
Report Page Generator: USV_RPG_ERR_FACTOR_STREAM (Stream access error).

CF620
Component: EventManager. Category: KM-Entity. Failed to obtain/receive event from framework.

CF620
Unable to Print.

CF620
System Error. Error acquiring the event data. Panel detects CF000 as same error.

CF620
System Error. Error acquiring the event data. Panel detects CF000 as same error. Unable to Load Files To CF Card.

CF630
Component: PowerManagement. Category: OS. Failed to mount or unmount during transition of the condition.

CF710
Component: IIS. Category: NetApl. Network file written error (inetd).

CF713
Component: IIS. Category: NetApl. Entity error (inetd).

CF720
Component: IIS. Category: NetApl. Network file written error (services).

CF723
Component: IIS. Category: NetApl. Entity error (services).

CF730
Component: IIS. Category: NetApl. Network file written error (snmpd).

CF733
Component: IIS. Category: NetApl. Entity error (snmpd).

CF743
Component: IIS. Category: NetApl. Entity error (hosts allow).

CF750
Component: IIS. Category: NetApl. Network file written error (hostname).

CF753
Component: IIS. Category: NetApl. Entity error (hostname).

CF760
Component: IIS. Category: NetApl. Network file written error (papd).

CF763
Component: IIS. Category: NetApl. Entity error (papd).

CF770
Component: IIS. Category: NetApl. Network file written error (cups).

CF773
Component: IIS. Category: NetApl. Entity error (cups).

CF780
Component: IIS. Category: NetApl. Network file written error (dhcclient).

CF783
Component: IIS. Category: NetApl. Entity error (dhcclient).

CF790
Component: IIS. Category: NetApl. Network file written error (smb).

CF793
Component: IIS. Category: NetApl. Entity error (smb).

CF7A0
Component: IIS. Category: NetApl. Network file written error (netware).

CF7A3
Component: IIS. Category: NetApl. Entity error (netware).

CF7B0
Component: IIS. Category: NetApl. Network file written error (ipfilter).

CF7B3
Component: IIS. Category: NetApl. Entity error (ipfilter).

CF7C0
Component: IIS. Category: NetApl. Network file written error (ethermode).

CF7C3
Component: IIS. Category: NetApl. Entity error (ethermode).

CF7D0
Component: IIS. Category: NetApl. Network file written error (other).

CF7D3
Component: IIS. Category: NetApl. Entity error (other).

CF7D7
Readout Error of SSL (authentication data).

CFAxx
HDD Error.

CFAxx
HDD Error.

CFA10
Component: OS_TOOLS. Category: OS. Error inside of hot plug detection thread, overwritten thread (failed to issue the event, failed to operate signal handler).

CFA20
Component: OS_TOOLS. Category: OS. Failed to obtain memory size.

CFA23
Component: OS_TOOLS. Category: OS. Access error to the Entity at master data stored area component.

CFA30
Component: OS_TOOLS. Category: OS. CF-DETECT OPEN error <0x07>.

CFA30
Component: OS_TOOLS. Category: OS. CF-DETECT IOCTL error <0x08>.

CFA30
Component: OS_TOOLS. Category: OS. CF-DETECT CLOSE error <0x09>.

CFA30
Component: OS_TOOLS. Category: OS. AES conversion OPEN error <0x0a>.

CFA30
Component: OS_TOOLS. Category: OS. AES conversion IOCTL error <0x0b>.

CFA30
Component: OS_TOOLS. Category: OS. AES conversion CLOSE error <0x0c>.

CFA30
Component: OS_TOOLS. Category: OS. AES conversion command return value error <0x0d>.

CFA30
Component: OS_TOOLS. Category: OS. Message queue creation error <0x15>.

CFA30
Component: OS_TOOLS. Category: OS. Message queue Tx error <0x16>.

CFA30
Component: OS_TOOLS. Category: OS. Message queue Rx error <0x17>.

CFA30
Component: OS_TOOLS. Category: OS. Message queue deletion error <0x18>.

CFA37
Component: OS_TOOLS. Category: OS. Event Tx error <0x19>.

CFA43
Component: OS_TOOLS. Category: OS. Access error to the Entity at USB activation component.

CFB00
Component: Panel. Category: KI-Panel. Netfront error (SLIM_E_GENERIC).

CFB01
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_INVAL).

CFB02
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_NOSERVER).

CFB03
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_TIMEDOUT).

CFB04
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_NOTFOUND).

CFB05
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_OPEN).

CFB06
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_CONNECT).

CFB07
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_READ).

CFB08
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_WRITE).

CFB09
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_CONNECT).

CFB0A
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_HANDSHAKE).

CFB0B
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_READ).

CFB0C
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_WRITE).

CFB0D
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQTIMEDOUT).

CFB0E
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_RSPTIMEDOUT).

CFB0F
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_CACHE_NONE).

CFB10
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_CACHE_EXPIRE).

CFB11
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_AUTH_UNKNOWN).

CFB12
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_AUTH_NOHEADER).

CFB13
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_AUTH_FORMAT).

CFB14
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REDIRECT_FORMAT).

CFB15
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REDIRECT_CANCELLED).

CFB16
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQ_HEADER_SIZEOVER).

CFB17
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQ_BODY_SIZEOVER).

CFB18
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_RSP_HEADER_SIZEOVER).

CFB19
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQ_TOOMANYCONTINUE).

CFB1A
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TLS_INTOLERANT).

CFB1B
Component: Panel. Category: KI-Panel. Netfront error (SLIM_FILEP_E_OPEN).

CFB1C
Component: Panel. Category: KI-Panel. Netfront error (SLIM_FILEP_E_READ).

CFB1D
Component: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_SIZEOVER).

CFB1E
Component: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_NO_CONTENT).

CFB1F
Component: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_TOOMANYREDIRECT).

CFB20
Component: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_TOOMANYAUTH).

CFB21
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_NOMEMORY).

CFB22
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_NOMEMORY_IMAGE).

CFB23
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_TOTAL_SIZEOVER).

CFB24
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_BADURL).

CFB25
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_BADMIMETYPE).

CFB26
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_MIXEDSECURETYPE).

CFB27
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_INPUTHISTORY_SIZEOVER).

CFB28
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_INPUT_REQUIRED).

CFB29
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_NOTIFYMAXWINDOW).

CFB2A
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_SWKOVERFLOW).

CFB2B
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_FILEDOWNLOAD).

CFB2C
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_SEGFAULT).

CFB2C CFB30 CFB31
Panel Error. NetFont error. Communication error between panel and main controller during initialization or rejection of communication by controller during initialization. Blue Screen of Death.

CFB30
Component: Panel. Category: KI-Panel. Failed to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode.

CFB30
Incompatible Level Of Firmware on Main EEPROM.

CFB30
Incompatible Level Of Firmware on Main EEPROM.

CFB31
Component: Panel. Category: KI-Panel. Refused to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode.

CFB31
Corrupt Firmware on Main EEPROM.

CFB31
Corrupt Firmware on Main EEPROM.

CFB32
Component: Panel. Category: KI-Panel. Time to start up request command (start up request command could not be received). Blue back screen. Cannot enter maintenance mode.

CFB32
Panel Error. Timeout request for start up command. Start command hasn’t been received. Possible destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death.

CFB33
Component: Panel. Category: KI-Panel. Cut off of the communication with the controller is detected — waiting to receive: select () OK return, recv() RX data length 0. Blue back screen. Cannot enter maintenance mode.

CFB33
Panel Error. Detects disconnection with controller. Possible overdrive of control board or destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death.

CFB34
Component: Panel. Category: KI-Panel. Time out for Response telegraphic message (could not receive response telegraphic message within a fixed time). In case on not through httpd, this error occurs (in case it does not become CGI time out).

CFB35
Component: Panel. Category: KI-Panel. Received abusive command from controller. At this moment, only the case that unexpected command comes in when wating for the startup request command.

CFB36
Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. select () function returned the error (other than EINTR).

CFB37
Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. rcv () function returned the error.

CFB38
Component: Panel. Category: KI-Panel. Communication error is detected when transferring (using UNIX domain) response telegraphic message in the panel. send() function returned the error (other than EINTR).

CFB39
Component: Panel. Category: KI-Panel. Crucial error is detected when processing receive/transfer of the response telegraphic message from controller. Failed to acquire semafo???

CFB3A
Component: Panel. Category: KI-Panel. Communication error is detected when sending required response telegraphic message from panel. send() function returned the error (other than EINTR).

При попытке сканирования документов с принтеров Kyocera на электронную почту пользователи иногда сталкиваются с ошибкой соединения 0x2202. Эта ошибка указывает на проблему в установке или конфигурации сетевых настроек принтера или сервера электронной почты.

Ошибки соединения могут возникать по разным причинам, например, неправильно введенные настройки SMTP-сервера, проблемы с сетевым соединением или ограничениями на отправку электронной почты с принтера.

Для решения проблемы с ошибкой соединения 0x2202 при сканировании на почту с принтеров Kyocera необходимо выполнить несколько шагов. Во-первых, убедитесь, что настройки сетевого подключения принтера и сервера электронной почты корректны. Проверьте правильность ввода адреса SMTP-сервера, порта, имени пользователя и пароля.

Если настройки сети верны, попробуйте изменить настройки SSL и авторизации на принтере. Некоторые SMTP-серверы требуют наличие SSL-соединения или авторизации для отправки электронной почты. При необходимости уточните требования вашего почтового провайдера и настройте принтер соответственно.

В случае, если все настройки правильны и ошибка соединения 0x2202 kyocera при сканировании на почту все еще появляется, свяжитесь с технической поддержкой Kyocera или вашего почтового провайдера. Провайдер может предоставить дополнительную информацию о настройках или проверить наличие каких-либо ограничений, которые могут препятствовать отправке почты с принтера.

Ошибки соединения 0x2202 на устройствах Kyocera

Ошибка соединения 0x2202 является наиболее частой проблемой при сканировании на почту на устройствах Kyocera. Она указывает на проблемы с подключением к серверу электронной почты и может быть вызвана несколькими причинами.

Возможные причины ошибки 0x2202:

1. Неправильно настроенные параметры соединения с почтовым сервером.
2. Неправильно указанное имя пользователя или пароль.
3. Проблемы с сетевым подключением, такие как низкая скорость соединения или неполадки в сети.
4. Ограничения безопасности на стороне сервера, которые блокируют соединение с устройством Kyocera.
5. Проблемы с SSL-сертификатом, который используется для защищенного соединения.

Как решить проблему:

1. Проверьте настройки соединения с почтовым сервером в меню устройства Kyocera. Убедитесь, что правильно указаны адрес сервера, порт, имя пользователя и пароль.
2. Убедитесь, что имя пользователя и пароль корректны, и они имеют доступ к почтовому серверу.
3. Проверьте сетевое подключение устройства Kyocera. Убедитесь, что скорость соединения достаточна для передачи данных.
4. Обратитесь к администратору почтового сервера, чтобы узнать о возможных ограничениях безопасности, которые могут блокировать соединение с устройством Kyocera. Попросите администратора разрешить соединение.
5. Если используется SSL-соединение, проверьте SSL-сертификат на устройстве Kyocera. Убедитесь, что сертификат действителен и соответствует серверу.

Если после выполнения этих шагов проблема не устраняется, рекомендуется обратиться в службу поддержки Kyocera для получения дополнительной помощи. Техническая поддержка сможет провести диагностику и предложить наиболее подходящее решение для ваших конкретных условий.

Причины ошибки 0x2202

Ошибка соединения 0x2202 является распространенной проблемой при сканировании документов и отправке их на электронную почту с использованием устройств Kyocera. Возможные причины этой ошибки могут включать следующее:

1. Неправильные параметры настроек SMTP сервера: Неправильно указанные параметры сервера и аутентификации могут привести к ошибке соединения 0x2202. Убедитесь, что вы правильно ввели настройки сервера, включая адрес сервера, порт, имя пользователя и пароль.
2. Проблемы с сетевым подключением: Ошибка 0x2202 может возникнуть, если устройство не может установить соединение с SMTP сервером из-за проблем с сетевым подключением. Убедитесь, что устройство имеет стабильное сетевое подключение и что нет проблем с маршрутизацией или фаерволом.
3. Неподдерживаемый протокол шифрования: Если настройки сервера указывают на использование протокола шифрования, который не поддерживается устройством Kyocera, возникнет ошибка 0x2202. Проверьте настройки сервера и убедитесь, что выбранный протокол поддерживается устройством.
4. Проблемы с идентификацией пользователя: Если у вас есть требование к аутентификации пользователя на SMTP сервере, убедитесь, что вы правильно ввели имя пользователя и пароль. Неправильные учетные данные могут вызвать ошибку соединения 0x2202.
5. Проблемы с указанием пути сохранения сканированных документов: Если в настройках устройства указан неправильный путь для сохранения сканированных документов перед отправкой на почту, это может привести к ошибке 0x2202. Убедитесь, что путь сохранения указан правильно и устройство имеет доступ к этому пути.

Если вы столкнулись с ошибкой 0x2202 при сканировании на почту с помощью устройства Kyocera, рекомендуется проверить указанные выше причины и соответствующим образом устранить возможные проблемы. В случае необходимости, обратитесь к документации или службе поддержки Kyocera для получения дополнительной помощи и решения проблемы.

Неверные настройки сетевого соединения

Ошибка соединения 0x2202 kyocera при сканировании на почту может возникать из-за неверных настроек сетевого соединения. В этом случае, проблема может быть связана с некорректным конфигурированием SMTP-сервера, неправильными учетными данными или проблемами с доступом к сети.

Для решения данной проблемы, рекомендуется выполнить следующие шаги:

1. Убедитесь, что у вас есть корректные настройки SMTP-сервера. Проверьте правильность имени сервера, порта, типа шифрования и требованиями аутентификации.
2. Проверьте правильность введенных учетных данных. Убедитесь, что вы ввели правильный адрес электронной почты и пароль.
3. Убедитесь, что устройство имеет достаточные права доступа к сети. Если у вас есть фаервол или другие сетевые настройки, проверьте, что устройство может связываться с SMTP-сервером.

Если после выполнения этих шагов проблема не решается, рекомендуется обратиться к специалистам технической поддержки для дальнейшей помощи и диагностики проблемы.

Проблемы с почтовым сервером

При использовании сканирования на почту на устройствах Kyocera может возникнуть ошибка соединения 0x2202. Эта ошибка указывает на проблемы с подключением к почтовому серверу.

Существует несколько причин, по которым возникают проблемы с почтовым сервером:

• Неверные настройки сервера: проверьте правильность введенных параметров для подключения к почтовому серверу, таких как адрес сервера, порт и тип подключения (например, POP3 или IMAP).
• Неправильные учетные данные: убедитесь, что вы вводите правильный адрес электронной почты и пароль для вашей учетной записи на почтовом сервере.
• Ограничения безопасности: некоторые почтовые серверы имеют дополнительные ограничения безопасности, которые могут блокировать подключение с устройства Kyocera. Уведомите администратора почтового сервера о проблеме и попросите проверить настройки безопасности.
• Сетевые проблемы: проверьте, что ваше устройство Kyocera правильно подключено к сети и имеет доступ к интернету. Если у вас постоянно возникают проблемы с подключением к почтовому серверу, свяжитесь с вашим системным администратором или поставщиком услуг интернета для проверки сетевых настроек и проблем.

Если вы все еще испытываете проблемы с подключением к почтовому серверу при сканировании на почту на устройствах Kyocera, рекомендуется обратиться к специалисту по поддержке Kyocera или вашему системному администратору для получения дальнейшей помощи и настройки.

Решение проблемы ошибки 0x2202

Одной из распространенных проблем, с которой часто сталкиваются пользователи принтеров Kyocera при сканировании на почту, является ошибка соединения 0x2202. Эта ошибка указывает на то, что принтер не может установить соединение с почтовым сервером для отправки отсканированных документов.

Существует несколько возможных причин этой ошибки, а также несколько способов ее решения. Вот некоторые из них:

Проверьте настройки сети

Возможно, проблема связана с неправильными настройками сети на вашем принтере. Убедитесь, что все настройки сети, такие как IP-адрес и шлюз по умолчанию, правильно введены и соответствуют настройкам вашей локальной сети.

Проверьте настройки почтового сервера

Если вы уверены в правильности настроек сети, возможно, проблема заключается в настройках вашего почтового сервера. Убедитесь, что вы правильно указали адрес сервера, порт, имя пользователя и пароль для отправки почты.

Проверьте соединение с сервером

Если у вас есть доступ к почтовому серверу, попробуйте проверить, может ли ваш принтер установить соединение с ним. Для этого можно использовать команду «telnet» в командной строке вашего компьютера. Если соединение не устанавливается или вы получаете ошибку, возможно, проблема связана с настройками сети или с самим сервером.

Обратитесь к специалисту

Если вы не можете самостоятельно решить проблему, рекомендуется обратиться к специалисту или службе поддержки Kyocera. Они смогут помочь вам найти и исправить причину ошибки 0x2202.

В завершение, хотелось бы отметить, что ошибка соединения 0x2202 является довольно распространенной проблемой при сканировании на почту с принтеров Kyocera. Однако с правильной настройкой сети и почтового сервера, а также с помощью специалистов, вы сможете успешно ее решить и наслаждаться безупречной работой вашего принтера Kyocera.

Проверка настроек сетевого соединения

Если возникает ошибка соединения 0x2202 при сканировании на почту на принтере Kyocera, первым шагом необходимо проверить настройки сетевого соединения. Ниже приведены несколько шагов, которые помогут вам в этом процессе:

1. Проверьте подключение к Интернету:

Убедитесь, что ваш принтер Kyocera имеет активное подключение к Интернету. Вы можете проверить это, попробовав открыть любой веб-сайт на принтере.

2. Проверьте правильность настроек сети:

Убедитесь, что у вас правильно настроены параметры сетевого соединения на принтере. Откройте настройки принтера и найдите раздел «Сетевые настройки». Убедитесь, что вы правильно указали IP-адрес, подмаску, шлюз и DNS-сервер.

3. Проверьте настройки безопасности:

Некоторые сети имеют ограничения для исходящего трафика. Убедитесь, что на вашем принтере разрешены сканирование и отправка электронной почты. Если вам необходимо включить эти функции, обратитесь к администратору сети.

4. Проверьте правильность данных учетной записи:

Убедитесь, что у вас правильно указаны данные учетной записи электронной почты на принтере. Проверьте адрес электронной почты отправителя, адрес электронной почты получателя и параметры сервера электронной почты (SMTP-сервер, порт, метод авторизации).

5. Проверьте настройки фаервола:

Фаервол может блокировать исходящий трафик с принтера. Убедитесь, что настройки фаервола разрешают исходящий трафик для принтера Kyocera.

6. Перезагрузите принтер:

Иногда перезагрузка принтера может помочь восстановить сетевое соединение. Выключите принтер, подождите несколько секунд и затем снова включите его.

Если после выполнения всех указанных выше шагов проблема все еще не решена, рекомендуется обратиться к специалисту технической поддержки Kyocera для дальнейшей помощи.

Проверка настроек почтового сервера

Если у вас возникла ошибка соединения 0x2202 при сканировании на почту на принтере Kyocera, проблема может быть связана с неправильными настройками почтового сервера. Для решения этой проблемы важно проверить следующие настройки:

1. SMTP-сервер: Проверьте правильность введенного SMTP-сервера. Убедитесь, что адрес сервера указан без ошибок и полностью соответствует требованиям провайдера. Обратите внимание на использование порта SMTP, который может быть указан вместе с адресом сервера.
2. Порт SMTP: Убедитесь, что указанный порт SMTP соответствует настройкам провайдера. Обычно порт SMTP равен 25 или 587, но возможны и другие варианты.
3. Аутентификация: Проверьте, правильно ли настроена аутентификация на почтовом сервере. Если ваш провайдер требует аутентификации, убедитесь, что вы указали правильное имя пользователя и пароль.
4. Шифрование: Проверьте, требуется ли на почтовом сервере шифрование. Если да, убедитесь, что правильно указан тип шифрования (например, SSL или TLS).
5. Проверка сертификата: Если на почтовом сервере используется самоподписанный сертификат, убедитесь, что в настройках принтера указано разрешение на подключение к серверу с недоверенным сертификатом.

После проверки настроек почтового сервера сохраните изменения и выполните повторное сканирование на почту на принтере Kyocera. Если проблема не устранена, рекомендуется обратиться в службу поддержки производителя для получения дополнительной помощи.

Ошибка соединения 0x2202 kyocera при сканировании на почту является довольно распространенной проблемой, с которой могут столкнуться пользователи устройств Kyocera при использовании их функции сканирования. Уведомление об этой ошибке означает, что устройство не может установить соединение с сервером электронной почты и не может отправить отсканированный документ на указанный адрес.

Существует несколько возможных причин этой ошибки. Одной из них может быть неправильно настроенный сервер электронной почты. Возможно, адрес сервера, порт или другие настройки указаны неверно. Еще одной возможной причиной может быть проблема с интернет-соединением на устройстве Kyocera. Проверьте подключение к сети и убедитесь, что устройство имеет доступ к Интернету.

Исправление ошибки соединения 0x2202 kyocera при сканировании на почту может потребовать нескольких действий. Первым шагом рекомендуется проверить настройки сервера электронной почты на устройстве Kyocera и убедиться, что они введены правильно. Если вы не уверены, какие значения должны быть указаны, обратитесь к администратору почтового сервера или поставщику услуг электронной почты для получения дополнительной помощи.

Если проблема с соединением все еще не решена, можно попробовать перезагрузить устройство Kyocera и проверить, корректно ли установлено и функционирует интернет-соединение. Если все остальные аспекты работы устройства функционируют правильно, возможно, проблема связана именно с функцией сканирования на почту, и требуется дальнейшее техническое обслуживание или консультация со службой поддержки Kyocera.

Ошибка соединения 0x2202 kyocera при сканировании на почту

Ошибка соединения 0x2202 kyocera при сканировании на почту может возникать по разным причинам. Эта ошибка указывает на проблемы с соединением и предотвращает отправку отсканированных документов на почту. В данной статье мы рассмотрим возможные причины ошибки и способы ее исправления.

Причины ошибки 0x2202 при сканировании на почту:

1. Неправильные настройки почтового сервера: Неправильно настроенный почтовый сервер может быть одной из причин ошибки. Убедитесь, что вы указали правильные адреса сервера и порт для отправки электронной почты.
2. Проблемы с сетевым подключением: Перебои или проблемы с сетевым подключением могут вызывать ошибку соединения. Убедитесь, что ваше устройство имеет стабильное сетевое соединение.
3. Неправильные учетные данные: Неправильно указанные данные для аутентификации на почтовом сервере могут привести к ошибке. Убедитесь, что вы указали правильные учетные данные для доступа к вашей почте.
4. Проблемы с безопасностью: Некоторые почтовые серверы могут блокировать попытки отправки электронной почты с устройств, которые не аутентифицируются с помощью SSL или TLS. Убедитесь, что вы правильно настроили безопасность соединения.

Способы исправления ошибки 0x2202 при сканировании на почту:

• Проверьте настройки почтового сервера: Убедитесь, что вы правильно настроили адрес сервера и порт для отправки электронной почты. Проверьте эти настройки в меню устройства и сравните их с настройками вашего почтового провайдера.
• Проверьте сетевое подключение: Если у вас возникают проблемы с сетевым подключением, попробуйте перезагрузить маршрутизатор или проверить уровень сигнала Wi-Fi. Убедитесь, что ваше устройство имеет стабильное подключение к интернету.
• Проверьте правильность учетных данных: Проверьте, правильно ли вы указали учетные данные для аутентификации на почтовом сервере. Убедитесь, что вы правильно ввели адрес электронной почты и пароль.
• Настройте безопасность соединения: Если ваш почтовый сервер требует безопасного соединения, убедитесь, что вы правильно настроили SSL или TLS. В некоторых случаях может потребоваться обратиться к вашему почтовому провайдеру для получения подробной информации о настройке безопасности.

После применения этих способов проверьте, работает ли отправка сканированных документов на почту. Если проблема по-прежнему возникает, рекомендуется обратиться к службе поддержки производителя устройства для получения дополнительной помощи.

Возможные причины ошибки

Ошибка соединения 0x2202 kyocera при сканировании на почту может возникать по разным причинам. Рассмотрим основные из них:

• Неправильные настройки сетевого подключения: проверьте правильность настроек сетевого подключения на принтере Kyocera. Убедитесь, что принтер правильно подключен к сети и настройки IP-адреса, подсети, шлюза и DNS указаны корректно.
• Проблемы с доступом к почтовому серверу: убедитесь, что у вас есть правильные настройки сервера электронной почты, такие как имя сервера, порт, тип безопасного подключения (SSL/TLS) и учетные данные для доступа.
• Ограничения брандмауэра или антивирусной программы: проверьте настройки брандмауэра и антивирусной программы на компьютере, к которому подключен принтер. Убедитесь, что сканирование на почту не блокируется и нет ограничений для работы принтера.
• Проблемы с почтовым сервисом: возможно, причина ошибки связана с проблемами на стороне почтового сервиса. Убедитесь, что сервис работает исправно и нет временных сбоев или ограничений в работе.
• Неправильная настройка принтера: проверьте все настройки принтера, связанные с отправкой сканированных документов на почту. Убедитесь, что указан правильный адрес электронной почты назначения, а также другие необходимые параметры.

Если вы исключите все вышеперечисленные причины и ошибка соединения 0x2202 kyocera при сканировании на почту все еще остается, рекомендуется обратиться в службу поддержки Kyocera или к специалисту по настройке и обслуживанию принтеров. Они смогут помочь вам диагностировать и исправить проблему.

Способы исправления ошибки

Ошибки соединения 0x2202 при сканировании на почту на принтерах Kyocera могут возникать по разным причинам. В данной статье рассмотрим несколько наиболее распространенных проблем и способы их исправления.

1. Проверьте настройки сетевого соединения

   Убедитесь, что принтер правильно подключен к сети и имеет доступ к Интернету. Проверьте правильность настроек IP-адреса, подсети, шлюза и DNS-серверов. Если настройки неверные, отредактируйте их в соответствии с требованиями вашей сети.

2. Проверьте правильность настроек электронной почты

   Убедитесь, что вы ввели правильные параметры SMTP-сервера и учетные данные для доступа к почтовому ящику. Проверьте, что принтер имеет права на отправку электронных писем через указанный почтовый сервер.

3. Проверьте наличие проблем с SSL-сертификатом

   Если настройка принтера требует использования SSL-сертификата для защищенного соединения, убедитесь, что сертификат установлен и действителен. Если проблема возникает при попытке подключения к самоподписанному или недействительному сертификату, следует обратиться к системному администратору для получения правильного сертификата.

4. Проверьте наличие блокировки портов или брандмауэра

   Возможно, ваш компьютер или сетевое устройство блокирует доступ принтера к интернет-сервисам. Проверьте настройки брандмауэра, а также доступность и наличие блокировки портов, необходимых для работы принтера.

5. Обновите прошивку принтера

   Иногда проблема может быть связана с устаревшей прошивкой принтера. Посетите официальный сайт производителя и загрузите последнюю версию прошивки для вашей модели принтера. Обратите внимание, что обновление прошивки несет определенные риски, поэтому перед выполнением данной процедуры ознакомьтесь с инструкцией по обновлению прошивки.

Если ни один из перечисленных выше способов не помог вам решить проблему, рекомендуется обратиться за помощью к специалистам технической поддержки Kyocera или к системному администратору вашей сети.

Как избежать ошибки в будущем

Чтобы избежать ошибки соединения 0x2202 при сканировании на почту на принтере Kyocera, следует учесть несколько важных моментов:

1. Проверьте настройки сети: убедитесь, что ваш принтер Kyocera правильно настроен для подключения к сети. Проверьте подключение кабелей, установите правильные IP-адреса и проверьте настройки протокола.

2. Обновите программное обеспечение: регулярно проверяйте, что на принтере Kyocera установлена последняя версия прошивки и драйверов. Обновление программного обеспечения может исправить известные ошибки и проблемы с сетью.

3. Проверьте настройки почтового сервера: убедитесь, что вы правильно настроили почтовый сервер на принтере Kyocera. Проверьте правильность указания адреса сервера, порта и учетных данных.

4. Используйте надежные и актуальные учетные данные: убедитесь, что вы используете правильные учетные данные для сканирования на почту. Проверьте, что ваш логин и пароль работают корректно и что у вас есть необходимые разрешения для отправки электронной почты через сервер.

5. Проверьте наличие ошибок в адресе получателя: убедитесь, что вы правильно указали адрес электронной почты получателя. Проверьте наличие опечаток или неправильных символов в адресе.

6. Обратитесь за помощью: если вы продолжаете испытывать проблемы даже после выполнения вышеуказанных действий, рекомендуется обратиться за помощью к специалистам. У них есть необходимые знания и опыт работы с принтерами Kyocera для решения проблемы и предоставления дополнительной поддержки.

Соблюдение этих рекомендаций поможет вам избежать ошибки соединения 0x2202 при сканировании на почту на принтере Kyocera и гарантировать бесперебойную работу вашего устройства.