Ошибка р1615 ниссан теана

Hi,
I have a problem programming a keyless for a Nissan Qashqai J10. First I try to program with MVP the programming sequence goes OK, but at end, neither customer key neither new key start the car.
Now I have IM608 also try to program key, but same problem.
DTC P1610 and P1615.
The programming sequence goes OK, immo light flashes 5 times, transponder block, but at end key don’t start the car.
Nissan Qashqai J10 VIN SJNFCAJ10U1125013
Year 2007
Bcm label 3 C4f1. Part number JD12CED.
284B2-JD12C.
Already looked at some posts, but can’t see a solution, or the only solution I found is new BCM and ECU from dealer. There is no other option?
New I-key :
https://drive.google.com/file/d/1545…w?usp=drivesdk
https://drive.google.com/file/d/1518…w?usp=drivesdk
Thanks in advance and happy new year.

[P1610]: LOCK MODE (dead lock mode)
[P1615]: DIFFERENCE OF KEY (BCM has received the ID signal of key and identified it
as the illegal）
NATS will enter into dead lock mode if using an unregistered or invalid key to start the
engine for more than five times, at this time, even though the correct car key also can not
normally start the engine. To unlock the mode, the system shall be initialized again. If the
detected DTCs are related to engine system, the related DTCs will also display on ECM.
Before clearing the DTCs memory on NATS, firstly check the DTCs on engine system
because while deleting the self-diagnostic codes of NATS, the memory on the «engine»
self-diagnosis system will also be cleared.
Perform «C/U INTIALIZATION again
X-431 or CONSULT-II will do job well

Last edited by lmqcatarino; 6th January, 2020 at 11:30 AM.

Originally Posted by rafal

[P1610]: LOCK MODE (dead lock mode)
[P1615]: DIFFERENCE OF KEY (BCM has received the ID signal of key and identified it
as the illegal）
NATS will enter into dead lock mode if using an unregistered or invalid key to start the
engine for more than five times, at this time, even though the correct car key also can not
normally start the engine. To unlock the mode, the system shall be initialized again. If the
detected DTCs are related to engine system, the related DTCs will also display on ECM.
Before clearing the DTCs memory on NATS, firstly check the DTCs on engine system
because while deleting the self-diagnostic codes of NATS, the memory on the «engine»
self-diagnosis system will also be cleared.
Perform «C/U INTIALIZATION again
X-431 or CONSULT-II will do job well

Hi,
I try to make the C/U initialization with x-431, but still don’t start the car.
I couldn’t clear DTC P1610 and P1615 after diagnosis.
Only way I could clear DTC was after key programing sequence don’t try start the car. Then I could clear DTC. Then y make C/U initialization,and key programming again, but no success.
On key programming, after programming transponder, it should registrate I-key function, but never could registrate, always error.
Just one question, when u make the C /U initialization, you program again just the exist I-key or a new one? Do you know if is possible to program just a spare pcf7936?

The only solution was take car to Nissan dealer.
I don’t know what they do to the car, but suppose it was just key reprogramming with Consult.
Old key and new key works now, so there wasn’t key problem.
Maybe just Consult can reprogram this I-key.

But I try with x-431 but I couldn’t make the C/U initialization.
Or I make some wrong step, or just Consult can do the job.

DRIVEL MODE:-

make sure drivers door open and closed when ignition off.

just you don’t get rid of key in chime/acc power until door open

DRIVEL MODE OFF:-

I have the same problem. It is impossible to add the keys, i.e. it is adding but it does not remember, the diode does not flash but goes out. The errors are also the same 1610,1612,1615. The dealer spreads his hands, says that the only option is to replace everything in the car. They claim that the consult does not program keys on-line. It is strange that it sometimes starts with a glowing immo indicator. Someone will help?