Ошибка p1481 04 опель

Начав разбираться в чем может быть проблема, выяснили, либо проблема в блоке управления на насосе, либо проблема в управляющих проводах, либо проблема в блоке управления на вентиляторе. Решили действовать методом исключения, раз у меня такой ошибки нет, поставить блок управления вентилятором в мою машину. Поставив его в мою машину , ошибка не выскочила. Далее начали прозванивать провода и обнаружили обрыв провода между блоком управления вентилятором и блоком предохранителя. Прокинув поверх провод, ошибка ушла, так мы побороли ошибку P1481-04 — Обрыв цепи вентилятора 1 скорости. В видео все показано как это было, так что всем приятного просмотра и до новых встреч.

https://youtu.be/S-NPkj4LQ50

• 
• Forum
• Technical
• Vectra C / Signum Troubleshooting
• Engine & Drivetrain
• P1481 fault code

Thanks:  0

Likes:  1

1. 11th May 2009, 06:17

   
   

   #31

   
   

   Originally Posted by ed taylor
   

   What did you do to solve it??.

   I had similar issues , found to be dirty connections on the Engine ecu itself .
   To get to mine properly (2.0 DTI) I had to take the egr valve off — good excuse for a clean. Then you can get to both connectors on the Engine ecu , gave mine a good clean , and it appears to have fixed the problem.
   I did this about 6 weeks ago.

   ---

2. 11th May 2009, 12:39

   
   

   #32

   

   
   Regular Member
   

   

   ---

   
   

   Update on mine.

   After having my service and changing my filters, cleaning the connections. it hasn’t come on in nealry 2 weeks now.
   I had a rely from my friends brither who works at VX and he says sometimes the fan sticks which gives this error, i did spin my fan when i cleaned my EGR so maybee that was it. fingers crossed atm .

   ---

3. 12th May 2009, 16:33

   
   

   #33

   

   
   Regular Member
   

   

   ---

   
   

   Hello all, i’ve got the same issue too.

   Order in which i’ll check it from all the advice, is 1st connections:

   Originally Posted by newtovectra
   

   check the two connectors in the front of the battery box. they connect to the top and bottom of the unit. this caused problems on my car.

   then fuses:

   Originally Posted by rob
   

   you might want to check out fuse 35 and 36 in underhood fuse box as these are the only fuses that control this cooling module.

   and then ECM from Rookie and stevedee3’s troubleshooting, the ECM (speaking with VX part number 24418358, �59.23 incl VAT):

   Originally Posted by stevedee3
   

   Well a couple of months ago, a dealer replaced my «cooling fan control module», and the problem hasn’t recurred, so I think I can say the problem is now fixed.

   ---

4. 15th May 2009, 15:03

   
   

   #34

   

   
   Regular Member
   

   

   ---

   
   

   Part changed, and now no spanner light for the first time in a year!

   it’s like driving a new car cheers Big Rich and Vectra-C for your help!

   ---

5. 15th May 2009, 17:48

   
   

   #35

   

   
   Regular Member
   

   

   ---

   
   

   Greta news Pete

   same here for me so far

   ---

6. 16th June 2009, 20:27

   
   

   #36

   Spanner is gone!
   

   My lucky day
   After mounting a new horn and relay the other day, I had to disconnect the battery, fuseboxes etc surrounding the battery. After that I got a constantly lit car/spanner, and I was afraid I had mounted something wrong, dismantled the fusebox and checked everything I could think of, but still the lit. Everything worked fine, but in one of these moments when standing at the engine and meditating of what this could be, I found the fans not to run when engine and AC was on. Hmm, it must be something at that circuit. Searced this forum, found this tread who gave me some hints, and started the seek again. After a few minutes, I found a loose connector at a box mounted to the batterybox, between the batterybox and the engine:
   

   Actually, it was not the connector who was loose, it was the complete plastic lid in the bottom, included the connector! I glued it together with some «super plastic», a dual component glue, just to be 110% sure this ******* will never ever loose again

   

   Here I have scribbled at the drawing of the batterybox

   newtovectra uploaded to this tread previously, to show where it is placed:
   
   So now it’s 1 more happy Vectra-owner

   ---

7. 13th January 2016, 23:09

   
   

   #37

   

   
   New Member
   

   

   ---

   
   

   Hi all. I have this dreaded code P1481-04 I’ve swapped the ecm checked the fuses, swapped the relays around by the fuse board and still have an issue with fan relay 1 open circuit.
   Running the fan tests from op com yield nothing from fan test 1 unsurprisingly.
   Test 2 works perfectly both fans spin up at full speed
   I’ve also got an issue where the fans don’t start up when starting the Ac but the car has always had that issue despite being regassed. Its only recently it has developed the spanner on the dash.

   I’m guessing it may be a ground issue, but I’m struggling to find the best place to look next.

   My car is a 2.0 DTI

   ---

8. Post Thanks / Like — 0 Thanks, 1 Likes

   

   evmav liked this post

Thread Information

Visitors found this page by searching for: