Ошибка p0300 toyota highlander

Степень важности ремонта : 3

Степень сложности ремонта : 3

• Неисправная свеча зажигания (s)
• Неисправная катушка зажигания (s)
• Засорение или неисправность топливной форсунки (s)
• Утечка всасываемого воздуха
• Обрыв или замыкание жгута проводов топливных форсунок
• Некачественное электрическое соединение в цепи топливных форсунок
• Обрыв или замыкание жгута катушек зажигания
• Цепь катушек зажигания плохо подключена
• Недостаточная компрессия в цилиндрах
• Неправильное давление топлива.

Как исправить код p0300 2004 toyota highlander?

Начните с проверки ‘Возможных причин’, перечисленных выше. Визуально осмотрите жгут проводов и разъемы. Проверьте наличие поврежденных компонентов и поищите сломанные, погнутые, вытолкнутые или корродированные контакты разъема

Код p0300 2004 toyota highlander технические заметки

Код P0300 означает, что цилиндр(ы) дает осечку или случайную осечку. Начните с проверки утечек во впускном коллекторе, прокладки впускного коллектора являются распространенной причиной осечек в нескольких цилиндрах. Если утечек не обнаружено, следующим шагом будет замена свечей зажигания. Если проблема сохраняется, необходимо провести дополнительные тесты для диагностики проблемы, см. раздел ‘Возможные причины’

Сколько стоит диагностика кода p0300 2004 toyota highlander?

Трудозатраты: 1. 0

Стоимость диагностики кода P0300 2004 Toyota Highlander составляет 1,0 час труда. Время диагностики и трудозатраты автосервиса зависят от местоположения, марки и модели автомобиля и даже типа двигателя. Большинство авторемонтных мастерских берут от 75 до 150 долларов США в час

Когда обнаруживается код p0300 2004 toyota highlander?

Модуль управления контролирует частоту вращения коленчатого вала и обнаружил осечку

Каковы возможные симптомы кода p0300 2004 toyota highlander?

• Горит лампочка двигателя (или предупреждающая лампочка Service Engine Soon)
• Отсутствие/потеря мощности
• Затрудненный запуск
• Колебания двигателя.

Что означает код p0300 2004 toyota highlander?

Когда происходит осечка, обороты двигателя колеблются. Если обороты двигателя колеблются настолько, что сигнал датчика положения коленчатого вала (CKP) меняется, модуль управления двигателем (ECM) может определить, что происходит осечка

What Does Toyota Highlander Code P0300 Mean?

• Toyota Highlander P0300 definition: Random, Multiple Misfire Detected
• Issue Severity: SEVERE – Stop driving immediately
• Repair Urgency: Fix this code immediately (same-day if possible) to avoid ignition failure, catalytic converter damage, and dangerous conditions
• Diagnosis: A multiple misfire can be caused by anything from faulty spark plugs to low engine compression. You can take your car into a shop, or click here to save money by fixing P0300 yourself with FIXD!

Your vehicle moves when gasoline is burned and power is generated inside a chamber known as the cylinder. Most engines have a 4, 6, or 8-cylinder engine, where more cylinders typically mean more power. Power is generated by pistons that move up and down while fuel is ignited at very specific times. A misfire typically occurs when the timing of this ignition is off. Toyota Highlander P0300 indicates that two or more cylinders are experiencing misfires.

Most Likely Repair And Cost For Toyota Highlander P0300 By Year

The chart below shows the most likely repair and cost range for Highlanders for all of the years that FIXD has data on.

Year	Most Likely Repair	Cost Range
2015	Engine Valve(s) w/P0301, P11ec	$1538 – $2008
2013	Ignition Coil(s)	$51 – $173
2012	Ignition Coil(s)	$51 – $173
2010	Ignition Coil(s)	$51 – $173
2009	Ignition Coil(s)	$51 – $173
2008	Ignition Coil(s)	$51 – $173
2007	Cylinder Head Gasket(s)	$2226 – $3770
2006	Ignition Coil(s)	$51 – $173
2005	Spark Plug(s)	$58 – $167
2004	Ignition Coil(s)	$51 – $173
2003	Variable Camshaft Timing (VCT) Solenoid	$1016 – $1531
2002	Variable Camshaft Timing (VCT) Solenoid	$1016 – $1531
2001	Variable Camshaft Timing (VCT) Solenoid	$1016 – $1531

Toyota Highlander P0300 Causes

Multiple misfires can be caused by many reasons from a faulty ignition system, fuel system, or internal engine failure. The most common reason for this to happen is faulty or worn-out spark plug coil packs, especially if it’s been a while since you had a tune-up.

• Faulty or worn spark plugs and/or spark plug wires
• Ignition issues, including failing or damaged ignition coils
• Distributor failure
• Faulty fuel injector
• Vacuum leak
• Low fuel pressure
• Camshaft and/or crankshaft sensor defective
• Engine timing off
• Leaking head gasket
• Low engine compression
• Poor quality fuel that is old or contaminated
• P0300 is not one of the top 5 trouble codes for the Toyota Highlander but, it is still a common one.

Toyota Highlander P0300 Symptoms

• Check Engine Light is on or flashing
• Engine runs rough, hesitates, or jerks when accelerating
• Drivers may not notice any adverse conditions when driving
• In some cases, drivers may experience decreased fuel economy, fuel smell from exhaust, rough idling, or lack of power from the engine
• Commonly associated with error codes: P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308

How Do I Fix Toyota Highlander Code P0300?

With a misfire fault, the first step is to get it diagnosed to figure out what is causing the engine to misfire. We’ve created this 100% free step-by-step guide to show you how to diagnose and fix your P0300 code.

>Click here to download your FREE P0300 Fix-It Guide!

If your vehicle is misfiring and you’re not comfortable diagnosing this issue at home, we recommend finding a RepairPal certified shop nearby to pinpoint the problem and give an accurate estimate for repairs.

These shops can not only help you figure out what’s going wrong before you waste time and money on the wrong parts, but they also offer a minimum 12-month, 12,000-mile warranty and stand behind all their estimates with guaranteed fair pricing.

How Much Does It Cost to Fix Toyota Highlander Code P0300?

P0300 can be caused by anything from old spark plugs to vacuum leaks to poor engine compression. It’s impossible to give an accurate estimate without properly diagnosing the issue first.

If you take your car to a shop for diagnosis, most shops will start with an hour of “diag time” (the time spent in labor diagnosing your specific issue). Depending on the shop’s labor rate, this typically costs somewhere between $75-$150. Many, if not most, shops will apply this diagnosis fee to any required repairs if you have them perform the repairs for you. From there, a shop will be able to give you an accurate estimate for repairs to fix your P0300 code.

Possible Repair Costs for Toyota Highlander P0300

Once properly diagnosed, P0300 may require one or more of the following repairs to resolve the underlying issue. These prices are based on national averages and include parts and labor. Your cost may differ depending on your location and type of vehicle.

• Spark plugs: $66-$250
• Ignition Coils: $230-$640 (some cars require Intake manifold removal)
• Spark plug wires: $180-$240
• Fuel injectors: $1500-$1900
• Vacuum leak: $100-$200
• Fuel pump: $1300-$1700
• Fuel pressure regulator: $200-$400

DIY Steps to Diagnose Toyota Highlander Code P0300

Engine code P0300 could be caused by a number of things, including faulty spark plugs, faulty ignition system, distributor failure, and more. If you’d like to try to fix code P0300 at home without throwing money at parts, you’ll want to follow the steps below for proper diagnosis. Keep in mind this is an intermediate-level diagnosis and repair and not recommended for beginners. Diagnosis requires more specialized equipment beyond what the FIXD Sensor can provide, and it can be a time and labor-intensive process for inexperienced DIYers.

DIY difficulty level: Intermediate

This repair requires mechanical knowledge and is not recommended for beginners.

Tools/parts needed (our top picks from Amazon):

• Screwdrivers
• FIXD
• Digital multimeter
• 5/8in. Spark Plug Socket
• Ratchet, sockets, and extensions
• Fuel pressure gauge
• Compression tester
• Leakdown tester
• Spark plugs
• Spark plug wires

STEP 1: USE FIXD TO ENSURE NO OTHER ENGINE CODES ARE PRESENT

Use FIXD to scan your Toyota Highlander vehicle to verify P0300 is the only code present. If other codes are present, they must be addressed first.

STEP 2: CHECK FOR LOOSE CONNECTORS OR DAMAGED WIRING AT THE IGNITION COILS.

Look for loose engine ground wires as well. These can cause random misfire conditions. Tighten or connect where necessary.

STEP 3: CHECK THE CONDITION OF YOUR SPARK PLUGS AND SPARK PLUG WIRES.

Worn and old spark plug wires are common causes of random misfires. Replace spark plugs and wires if needed and recheck for misfires.

STEP 4: CHECK TO ENSURE YOUR ENGINE IS GETTING THE PROPER AMOUNT OF FUEL.

If you have determined that your ignition system is operating correctly, there may be a problem within your fuel system that is causing the random misfires. The following should be checked to ensure the engine is getting the proper amount of fuel.

• Check fuel pressure: Low fuel pressure can cause intermittent misfires on multiple cylinders. When the pressure is below the specification, the engine does not receive the proper amount of fuel and will start to lean misfire. The fuel pump or fuel pressure regulator could be the source of the low fuel pressure.
• Check fuel injectors: Make sure the fuel injectors are functioning properly and activating. Random misfires can be a sign of faulty or clogged fuel injectors that need to be replaced. Also, check that the fuel injector wiring is not damaged and is connected properly.

STEP 5: PERFORM ENGINE COMPRESSION AND LEAKDOWN TEST.

If the ignition system and fuel system checks out, you may want to perform an engine compression test and leakdown test to see if there are any mechanical problems causing your misfire.

Common mechanical problems that can cause misfires:

• Leaking head gasket
• Broken valve spring
• Broken piston ring
• Worn valve guides
• Burned valve
• Timing chain or belt skipped tooth and engine is off time

Common Toyota Highlander P0300 Diagnosis Mistakes

Loose fitting electrical connectors and broken or disconnected vacuum hoses are often overlooked. Oxygen sensor(s) are another common misdiagnosis for P0300.

Still Need Help Fixing Toyota Highlander Code P0300?

If you’ve followed the steps above and are still experiencing Toyota Highlander check engine code P0300, please contact the FIXD Mechanic Hotline if you’re a FIXD Premium subscriber or find a RepairPal certified shop near you to get the right repairs at a fair price.

Fixed It But The Check Engine Light Is Still On?

Check engine light sometimes need to be reset manually, check out our article:

How to Reset Your Check Engine Light | 4 Ways To Clear It (With or Without a Scanner)

P0300 is a generic OBDII code that can occur with the Toyota Highlander. This code indicates that your vehicle’s engine is misfiring and can be a drivability threat.

P0300 is often accompanied by cylinder-specific misfire codes (P030X, where the X indicates the cylinder number that is misfiring). If you have P0300 and a cylinder-specific misfire, the cylinder indicated by the specific codes would be where to start looking for your problem.

Worn spark plugs, coil packs, or plug wires are the most common cause of P0300.

Table of Contents

• P0300 Meaning
• Symptoms
• Causes + Diagnosis
• Fixing P0300
• Common Questions

Definition	P0300: Random Multiple Misfire Detected.
Symptoms	Rough idle, jerks when accelerating, decreased MPG.
Common Causes	Ignition components or it’s a symptom of another problem.
Breakdown Risk?	Yes.
Repair Cost (Parts)	Typically less than $250 for the common issues.
Repair Difficulty	Easy, if it’s ignition related.

---

P0300 is a general diagnostic trouble code. Specifically, it indicates that there is a:

Random, Multiple Cylinder Misfire Detected

P0300 is a random misfire code, which means that it is not going to tell you which cylinder is causing the misfire.

Since something is causing cylinders to misfire randomly, figuring out the cause is less cut and dry than a cylinder-specific misfire code. This code can indicate an issue with the ignition system, but it is often a symptom of another problem.

How you approach P0300 depends on if there were any other codes present.

---

P0300 Symptoms: Toyota Highlander

There are almost always noticeable symptoms associated with P0300 other than the check engine light.

• Check engine light (it may be flashing, which indicates you should stop driving your vehicle ASAP).
• Your vehicle will likely have a noticeable misfire sound to it.
• Your Highlander will jerk while accelerating.
• Excess vibration, especially at lower RPM.
• Decreased fuel economy.

If your Highlander’s engine is misfiring enough to damage the catalytic converter, the check engine light may flash on and off as a warning to stop running the engine until you can fix it.

---

P0300 Trouble Code Causes + Diagnosis

When diagnosing the cause of P0300 in your Toyota Highlander the problem can be broken down into two main categories.

1. Something related to the ignition system caused the random misfire.
2. P0300 is a symptom of another engine problem.  

Important to pull and weigh all the codes together.  The misfiring could just be a symptom of the real problem.

For example, if you got a fuel pressure-related code, that indicates your Highlander’s fuel rail isn’t getting enough fuel pressure for the fuel injectors to work properly, which would cause a random misfire.

---

Spark Plugs, Plug Wires, or Coil Packs (Ignition)

Start here if your Highlander has only misfire/ignition-related codes.

The most likely cause of P0300 in most vehicles is a bad ignition component (particularly the spark plugs).

While most modern vehicles use iridium spark plugs that can last a long time, they still should be changed at Toyota’s recommended maintenance intervals.

If your Highlander has a few cylinder-specific trouble codes, it may be a good idea to check and see if there is any wiring damage around the wiring harness connecting the PCM to the coil packs.

Here’s how to test a coil pack, how to tell if a spark plug is bad (video), and how to test plug wires (video).

---

Low Fuel Pressure

If your Highlander’s fuel pressure is low, you may also encounter P0171 (fuel trim lean) or P0087 (fuel rail pressure too low).

If there isn’t enough fuel getting to the engine, it will keep leaning out the air-fuel mixture. 

If your vehicle’s fuel pressure is really low, it’ll cause noticeable misfiring as there won’t be enough fuel pressure to atomize the gasoline as it enters the combustion chamber.

Typically, if your Highlander has low fuel pressure, it’ll act fine when it doesn’t need a lot of fuel. But it’ll sputter and act like it will die at speed or under heavy acceleration.

As the fuel pressure decreases, it’ll start happening when you give it less and less gas. Or, your Highlander will shut down when driving but then turn back on.

It’s really easy to check the fuel pressure at the rail.  Autozone or any other parts store will usually have a loaner fuel pressure testing kit. 

The two most prevalent causes of low fuel pressure are an issue with the fuel pump or fuel regulation.

Here’s some information on how to tell if you have a bad fuel filter. Here’s how to test fuel pressure with a fuel pressure tester.

---

Vacuum Leak

P0171 is the most common code to see with a vacuum leak

If your Highlander has a vacuum leak, unmetered air is entering the combustion chamber, which usually leans out the air-fuel mixture.

A lean air/fuel ratio will cause the cylinders to misfire, and it’ll throw the P0300.

Since a vacuum leak almost always affects each cylinder the same, you’ll typically get P0300 with it and not any cylinder-specific misfire codes.

Here’s a great article from Popular Mechanics on how to detect a vacuum leak. Chasing one down is pretty easy. Popular Mechanics: How to find a vacuum leak.

---

Mechanical

Most mechanical issues won’t throw other codes.

Mechanical issues can cause misfiring. Here are the most common mechanical issues that can cause P0300:

• Blown or leaking head gasket– A compression test will confirm whether or not the head gasket is leaking.
• Engine timing– The timing chain could have jumped, or there could be an issue with the crank or cam sensor.
• Burned Valve or Broken Valve Spring– A burned valve will reduce the compression rate and cause a misfire.
• Clogged Catalytic Converter– A clogged cat can increase backpressure and cause misfiring.

---

Bad Gas

Old gas can cause misfiring.

If your misfire started a minute or two after filling up, it could be that your Highlander has some bad gas. The same goes if it’s been sitting for over 90 days.

---

How to Fix P0300 in the Toyota Highlander

P0300 will often be fixed by something obvious. When it’s not glaringly obvious what is wrong, a tune-up is a great place to start. Here’s a good order to approach fixing P0300 in the Toyota Highlander.

1. Check for other codes. Use them to eliminate as many of the causes listed above as you can.
2. Check the wiring harness going to the coil packs. Verify that it isn’t burnt, frayed, or otherwise damaged. If it’s wintertime, look for signs of rodent damage.
3. Pull a few random plugs. Replace them if needed.
4. Test the coil packs.
5. If your Highlander has plug wires. Run the engine in the dark and see if you see any spark “leaking”.
6. Check for a vacuum leak.
7. Test the fuel pressure.
8. Do a compression test.

---

Q & A

Q: Is P0300 a serious concern?

A: P0300 is cause for concern, and left unfixed can get worse. Left ignored, a misfire will eventually get bad enough that your Highlander may not start.

Q: Can a bad catalytic converter cause P0300?

A: Yes. A clogged converter will increase backpressure. An engine is a pump. When there’s too much backpressure, air can’t quickly move through the combustion chambers and will misfire.

Q: How do you clear P0300?

A: You can use an OBD II scanner to clear P0300 in the Toyota Highlander. You have to fix the root cause of P0300 in your vehicle. Otherwise, when you clear the code, it’ll come right back.