Jungheinrich System Error Codes list.pdf
Adobe Acrobat Document
168.2 KB
Jungheinrich Fault Codes.pdf
Adobe Acrobat Document
720.8 KB
Jungheinrich Error Codes List PDF.pdf
Adobe Acrobat Document
191.8 KB
Jungheinrich EJC112 & E1202 Event Messag
Adobe Acrobat Document
582.8 KB
Event Messages
Z This display units shows a four-digit event message for every
event. Trucks that only use one luminous display (e.g. LED) show
the event through a flashing code (see «Display System”).
Each event message is also stored in the master logbook. The
master logbook describes the event in more detail through the sub
index behind the event message (FEXX).
Event numbering display
F E XX S
F Function group; E Event group
XX Event number S Sub index
The first two characters “F, E” refer to the category. The middle
two digits “XX” refer to the event. From these two digits the range:
• 1 to 50 describes standard events (uniform basic events)
which can occur in any function group.
• 51 to 99 describes specific events.
The event is described in further detail through the last characters
“S” (single digit / multi-digit).
This process ensures that a unique number is assigned to each
event. Example:
0 Fault reset or
no fault
1 General fault / additional functions
Example:
Logic error, e.g. both directions selected simultaneously
2 Current
(input interface, device-internal, output interface)
3 Voltage
(input interface, device-internal, output interface)
4 Temperature
5 Hardware
Example: Output transformer short circuit, EEPROM not
responding, …
6 Software
(internal software, application software, data record /
parameters)
Example: EEPROM data error
7 Additional modules
8 CAN monitoring
9 External fault
Example: ISM
Jungheinrich System Error Codes list.pdf
Adobe Acrobat Document
168.2 KB
Jungheinrich Fault Codes.pdf
Adobe Acrobat Document
720.8 KB
Jungheinrich Error Codes List PDF.pdf
Adobe Acrobat Document
191.8 KB
Jungheinrich EJC112 & E1202 Event Messag
Adobe Acrobat Document
582.8 KB
Event Messages
Z This display units shows a four-digit event message for every
event. Trucks that only use one luminous display (e.g. LED) show
the event through a flashing code (see «Display System”).
Each event message is also stored in the master logbook. The
master logbook describes the event in more detail through the sub
index behind the event message (FEXX).
Event numbering display
F E XX S
F Function group; E Event group
XX Event number S Sub index
The first two characters “F, E” refer to the category. The middle
two digits “XX” refer to the event. From these two digits the range:
• 1 to 50 describes standard events (uniform basic events)
which can occur in any function group.
• 51 to 99 describes specific events.
The event is described in further detail through the last characters
“S” (single digit / multi-digit).
This process ensures that a unique number is assigned to each
event. Example:
0 Fault reset or
no fault
1 General fault / additional functions
Example:
Logic error, e.g. both directions selected simultaneously
2 Current
(input interface, device-internal, output interface)
3 Voltage
(input interface, device-internal, output interface)
4 Temperature
5 Hardware
Example: Output transformer short circuit, EEPROM not
responding, …
6 Software
(internal software, application software, data record /
parameters)
Example: EEPROM data error
7 Additional modules
8 CAN monitoring
9 External fault
Example: ISM
Some JUNGHEINRICH Forklift Trucks Error Codes
Sub-division of function group F
0 Dystem: Overlappingfunction that cannot be assigned to any other function group
1 Travel
2 Hydraulics (load handling)
3 Steering and travel
4 Displays / controls, interface
5 Charger (either on-board or external charger)
6 Reserved
7 Reserved
8 Reserved
9 Special Functions
Sub-division of event group E
0 Fault reset or no fault
1 General fault /additional functions
2 Current
3 Voltage
4 Temperature
5 Hardware
6 Software
7 CAN motitoring
8 External fault
See also: Jungheinrich Service Repair Manuals PDF
Jungheinrich Error Codes Manual PDF
Password: https://truckmanualshub.com/
Title | File Size | Download Links |
Jungheinrich EJC112 / E1202 Event Messages Codes List PDF [PDF] | 616.6kb | Download |
Jungheinrich Error Codes List PDF [PDF] | 198.4kb | Download |
Jungheinrich Fault Codes [PDF] | 769kb | Download |
Jungheinrich LISTADO ERRORES [PDF] | 198.4kb | Download |
Jungheinrich System Error Codes list [PDF] | 162.3kb | Download |
Jungheinrich system error table
Error | Description | Component | Display text | Cause / Action | Effect |
1 | Low voltage during system start | F, H, L,
F-AC, H-AC |
Low voltage ELECTRICAL SYSTEM | Check battery voltage, charge battery; Check wire connection to controller; check main current fuse; check main contactor; replace control part; Replace component;
(Limit VN = 80V: VBatt < 64V or VCap. < 56V Limit VN = 48V: VBatt < 34V or VCap. < 34V Limit VN = 24V: VBatt <17V) |
Travel is inhibited.
Reduced power for travel and lifting. Warning symbol flashing (Else-Check). |
2 | Over voltage | F, H, L,
F-AC, H-AC |
Over voltage BATTERY CONTROLLER | Check battery voltage; replace controller part; replace component; (Limit VN = 80V: VBatt > 92 V
Limit VN = 48V: VBatt > 62 V Limit VN = 24V: VBatt > 28 V) |
No travel or hydraulic functions Warning symbol
flashing (Else-Check). |
3 | Temperature limit for controllers
> 80°C (>70°C MP1510C) or ACS only: Info at > 85°C Err at > 115°C Err at < -20°C |
F, H, L,
F-AC, H-AC |
TEMPERATURE CONTROLLER | Check sensor and wire connections Allow controllers to cool down; check fan operation, improve cooling.
Warm up the controller and operate at reduced level until the controller has warmed up. |
Reduced power for travel and lifting.
Warning symbol flashing (Else-Check). |
4 | Emergency Disconnect applied during travel | F | POWER SUPPLY | Warning
(V < 20V MP1510C) |
Brake applies, travel inhibited |
Error | Description | Component | Display text | Cause / Action | Effect |
1 | Low voltage during system start | F, H, L,
F-AC, H-AC |
Low voltage ELECTRICAL SYSTEM | Check battery voltage, chargebattery; Checkwireconnectiontocontroller; check main current fuse; check main contactor; replace control part; Replacecomponent;
(Limit VN = 80V: VBatt < 64V or VCap. < 56V Limit VN = 48V: VBatt < 34V or VCap. < 34V Limit VN = 24V: VBatt <17V) |
Travel is inhibited.
Reduced power for travel and lifting. Warning symbol flashing (Else-Check). |
2 | Overvoltage | F, H, L,
F-AC, H-AC |
Overvoltage BATTERY CONTROLLER | Check battery voltage; replace controllerpart; replace component; (Limit VN = 80V: VBatt > 92 V
Limit VN = 48V: VBatt > 62 V Limit VN = 24V: VBatt > 28 V) |
No travel or hydraulic functions Warning symbol
flashing (Else-Check). |
3 | Temperature limit for controllers
> 80°C (>70°C MP1510C) or ACS only: Info at > 85°C Err at > 115°C Err at < -20°C |
F, H, L,
F-AC, H-AC |
TEMPERATURE CONTROLLER | Check sensor and wire connections Allow controllers to cool down; check fan operation, improve cooling.
Warm up the controller and operate at reduced level until the controller has warmed up. |
Reduced power for travel and lifting.
Warning symbol flashing (Else-Check). |
4 | Emergency Disconnect applied during travel | F | POWER SUPPLY | Warning
(V < 20V MP1510C) |
Brake applies, travel inhibited |
Error | Description | Component | Display text | Cause / Action | Effect |
5 | Over voltage | F, F-AC, H-AC | ELECTRICAL SYSTEM | Check wire connection to battery, check Battery, replace controller part; Replace component;
(Limit for Retrak: VBatt > 62 V Limit for MP1510C: V > 32 V) |
Brake applies, travel inhibited |
6 | Wire breakage:
– Travel set point device |
C, I2, I3, I4, I5,
Travel switch |
TRAVEL SWITCH | Check wire connection; Replace travel set point device; Replace Canion/ Interface; | Travel stop. “Warning” symbol flashes (Else-Check). Hydraulic functions possible |
7 | Key switch applied during travel | F,F-AC,H-AC | KEY SWITCH | Warning
(V < 13V for 200ms MP1510C) |
Brake applies, travel inhibited |
8 | 2 travel directions applied simultaneously | F-AC, H-AC, C,
MP, S, I2, I3, I5, FS |
ELECTRICAL SYSTEM | Warning, replace travel direction switch, replace Interface 7 Canion; replace Multi-pilot / Solo-pilot
For twin pedal, check the electrical system. |
Travel stop. “Warning” symbol flashing (Else-Check).
Hydraulic functions possible |
9 | Operator protection switch faulty | I2, FS | ELECTRICAL SYSTEM | Check switch, check wire connections | |
10 | V Cap. <> V Batt; (main
contactor jammed or not open) |
F, H,
F-AC, H-AC L |
MAIN CONTACTOR | Check main contactor, check wire connection; check output pin 2 (ACS) of traction controller; replace component | No travel, hydraulics Warning symbol
Flashing warning (Else-Check). |
11 | Offset error armature / field current (DC) Stator current (AC); Current measurement
point |
F, H, L,
F-AC, H-AC |
CONTROLLER | Check main current wire, replace component | Travel no function |
12 | Disable driver field rheostat faulty for DC Disable driver power stage faulty (for AC) | F, H
F-AC, H-AC L |
CONTROLLER | Replace component;
for AC: Check flat belt wire connection; replace power part |
No travel, hydraulics Warning symbol
Flashing warning (Else-Check). |
Error | Description | Component | Display text | Cause / Action | Effect |
13 | Disable Watchdog field faulty | F, H | CONTROLLER | Replace components | Travel no function |
14 | – Main contactor not closed
– Field power stage cannot be switched on (DC) |
F, H,
F-AC, H-AC |
CONTROLLER/ MAIN CONTACTOR | Check wire connection; check main contactor; check charging connection, Check field supply fuse,
Replace component. |
No travel, hydraulics Warning symbol
Flashing warning (Else-Check). |
15 | Disable field faulty; Illegal address (for AC) | F, H,
F-AC, H-AC L |
CONTROLLER | Replace control part; replace component | Travel no function |
16 | Disable driver armature
actuator faulty; Software reset (for AC) |
F, H,
F-AC, H-AC |
CONTROLLER | Replace control part (AC); replace component | Travel no function |
17 | Disable Watchdog armature faulty | F, H | CONTROLLER | Replace components | Travel no function |
18 | DC: Armature power stage cannot be switched on
AC: one of the 3 phases cannot be switched on |
F, H, F-AC, H-AC L | CONTROLLER | Check armature wire connection; replace power part; replace component | Travel no function |
Error | Description | Component | Display text | Cause / Action | Effect |
19 | Disable armature faulty; Power stage short circuit (for AC)
The error may be triggered by the faulty speed sensor in connection with AS4814Plus controllers. Sensor wheel wobbles (elliptical) or the sensor- sensor wheel gap is too big. In this case the component is not faulty. A short circuit cannot be resolved by switching the truck off/on. |
F, H, F-AC ,H- AC,
L-AC |
CONTROLLER | Replace power part; Replace component.
Can occur in connection with error 70, in this case: check power supply behind the main contactor contact, in the event of an error the voltage will be much lower here than the rated operating voltage. Disconnect the positive supply from the components to target the error cause. The exception here is the F1 traction controller which must remain connected. One component overloads the testing voltage due to internal short circuit. The testing voltage arises by charging the internal capacitor batteries via a resistor to the level of the control voltage supply. |
Travel no function |
Check sensor, replace sensor and / or sensor wheel. | |||||
20 | Armature incorrectly connected | F, H | ELECTRICAL SYSTEM | Check armature main current wire connection | Travel no function |
21 | Armature over voltage (short circuit / high side faulty) | F, H, F-AC, H-AC L | CONTROLLER/ ELECTR | Check main current wire to armature; check settings(for AC);
A Armature > 360A for 250ms (MP1510); Replace component. |
Error | Description | Component | Display text | Cause / Action | Effect |
22 | Watchdog error; Watchdog does not run out | F, H, L, M, S, A, I2, I3, I4, C,
F-AC, H-AC, FS |
CONTROLLER/ CANION | Truck reset,
Replace controlpart; replace component |
No travel, hydraulics Warning symbol
Flashing warning (Else-Check). |
23 | – Computer overload
– Permanent interrupt – “ACS” timeout on CAN connection |
F, H, L, M, S, A, I2, I3, I4, C,
F-AC, H-AC, FS |
CONTROLLER / CAN | Check CAN bus connection; Check CANION connector and component;
Replace component |
No travel, hydraulics Warning symbol
Flashing warning (Else-Check). |
24 | EEPROM cannot be contacted / parameters not plausible / parameter set to default
Faulty checksum |
F, H, L, I2, I3, I4, C,
F-AC, H-AC MFC brake MFC hydr. , travel switch |
CONTROLLER/ CANION | Check battery cable; check VBatt; set trucktype, set default parameters; replace control part; replace component
Delete logbook, change parameters, set hourmeter, replace component |
Flashing warning symbol (Else- Check). |
25 | No telegrams:
– no logon from interface – no telegrams from Can-Bus travel switch |
F, H, I4, I8
F-AC, H-AC L |
INTERFACE / CAN | Check CANBus connection, check wire connection between proportional valve
– modulation; check fuse 1F8; replace iInterface (I2, I4, I8) ; replace lift potentiometer, Multipilot, Solopilot or interface; MP1510C: Voltage collapses, controller logs on again, interface does not, controller remains blocked and waits for interface. Check battery voltage (with load!); charge or replace battery if necessary; AS2409K: no “live” telegram received from CAN Bus travel switch for more than 300 ms; replace travel switch |
Error | Description | Component | Display text | Cause / Action | Effect |
26 | Wire breakage:
– Lift potentiometer |
M, S, I2, I3 | MULTIPILOT / SOLOPILOT / LIFT POTENTIOMETER | Check wire connection | Lift stop. “Warning” symbol flashes (Else-Check), travel enabled |
27 | Wire breakage:
– Steering setpoint device; à Reach truck: for 45° steering bolster movement no flank from proximity switch. à Canion: “Steer angle acquire active” parameter has incorrect value à Juniors PM2402L: “Operating mode” parameter incorrectly set |
C, L, I3, I4 | STEER ACTUAL ANGLE | Check wire connection; Replace steer angle sensor / potentiometer;
Replace Canion / Interface; Replace steering; PM2402L from software version 1.60: set parameter P511 “operating mode” correctly à 1 = analog sensor (potentiometer), 2 = digital sensor on steer motor |
Crawl speed,
Flashing warning symbol (Else- Check), hydraulic functions enabled. This error produces an emergency stop on the reach truck and the Juniors. |
28 | Wire breakage:
– Steering sensor |
C, L, I3, I4 | STEER NOMINAL ANGLE | Check wire connection, replace steering wheel sensor;replace Canion / interface; replace steering | Crawl speed,
Flashing warning symbol (Else- Check), hydraulic functions enabled. This error produces an emergency stop on the reach truck |
29 | Wire breakage:
– Traverse potentiometer |
M | Traverse nominal value MULTIPILOT | Replace Multipilot | |
30 | Wire breakage:
– Tilt potentiometer |
M | Tilt nominal value MULTIPILOT | Replace Multipilot,
Teach Multipilot (Hall sensor 2003 only) |
|
31 | Wire breakage:
– ZH1 setpoint device – Initial lift / lower Setpoint device |
M, S
Travel switch |
Sideshift nominal value MULTIPILOT / SOLOPILOT | Replace Multipilot / Solopilot, Teach Multipilot (Hall sensor 2003 only);
Travel switch: Check / replace switch |
Hydraulic functions stop, “Warning” symbol flashes (Else-Check), travel enabled |
Error | Description | Component | Display text | Cause / Action | Effect |
32 | Wire breakage:
– ZH2 setpoint device |
M, S | MULTIPILOT / SOLOPILOT | Replace Multipilot / Solopilot,
Teach Multipilot (Hall sensor 2003 only) |
Hydraulic functions stop, “Warning” symbol flashes (Else-Check), travel enabled |
33 | Wire breakage:
– ZH3 setpoint device |
M, I8 | MULTIPILOT | Replace Multipilot | |
34 | CANBus damaged | F, H, L, M, S, A,
I2, I3, I4, I5, C, F- AC, H-AC Travel switch |
CAN-BUS | Check CAN bus connection; replace faulty component; Check terminal resistances | No travel, hydraulics Warning symbol
Flashing warning (Else-Check). Only stored in logbook (from 2004). |
35 | No travel zero position Deadman and accelerator pedal applied when truck switched on | I2, I3, I4, C
Travel switch |
TRAVEL ZERO POSITION | Warning, check travel switch; Intermittent contact in interface power supply (12 volts)
Check Canion, for twin pedal check electrical system |
Travel stop,
Flashing warning symbol (Else- Check), hydraulic functions enabled. |
36 | No lift zero position | M, I2, I3,FS | LIFT ZERO POSITION | Warning, check lift setpoint device. | Hydraulic functions stop, “Warning” symbol flashes (Else-Check), travel enabled |
37 | No steering angle nominal value | L | CONTROLLER / CAN | Check steering setpoint device;Check CANBus connection; check “steer type” parameter; Replace component (I5) | |
38 | Component does not log on, self test not concluded. | F, H, L, I2, I3, I4,
C, A, M, S, F-AC, H-AC |
CONTROLLER / CAN | Check CAN-Bus connection and voltage; check DIL switch 7 encoding (MP1510); steering controller monitoring activated? (AS2412F); check ACS encoding; replace component | No travel, lifting Warning symbol
Flashing warning (Else-Check). |
Error | Description | Component | Display text | Cause / Action | Effect |
39 | Implausible truck type
1. Discovered during the self test phase that at least one component has a different truck type as a parameter. A different truck type was discovered in operating mode. Caused by intermittent contacts in the power supply connections |
F, H, L, I2, I3, I4, I5, A, M,
F-AC, H-AC |
TRUCK TYPE | For 1. Set truck type;
For 2. Examine and if necessary replace switch (key switch) or rectify intermittent contact in power supply plug connections. Set truck type. |
|
40 | Motor overtemperature Traction motor overtemperature in operating mode.> 150°C And travel speed < 1km/h For ACS:
Info > 145°C Err > 165°C |
L, F, H
F-AC, H-AC |
TEMPERATURE MOTOR | Warning; check motor sensor system and wire connections;
Check motor; traction motor brake open? |
Reduced power for travel and lifting.
Warning symbol flashing (Else-Check). For steering only warning symbol flashing. |
41 | Brake magnet potentiometer Potentiometer voltage less than 0.3 volts or greater than 2.7 volts for more than 500ms. | L | BRAKE MAGNETPOTENTIOM ETER | Check potentiometer; check potentiometer attachment; check wire connection |
Error | Description | Component | Display text | Cause / Action | Effect |
42 | – Short circuit between the output and battery positive. (EJC, ELE)
-Brake magnet control, below minimum difference on potentiometer for 500ms when magnet applied. (150mV ) No brake pressure during initialization. Brake pressure after the Emergency Stop magnet has applied; |
L,F | BRAKE MAGNET | Check wire connection, check brake
magnet; replace component |
|
43 | Adjust brake | L | ADJUST BRAKE | Adjust brake; check potentiometer | |
44 | -Brake not connected or connection wire short circuit
-Brake cable torn Only for steer category_3: Internal driver of fail safe brake cannot connect the relay Or short circuit bypass (contact jams) on the output during power up test |
L,F | BRAKE FAULTY | -Check brake wiring, replace brake if necessary
-Replace brake cable, check potentiometer; Check potentiometer attachment; Only for steer category_3: -Check brake driver output, check switch contact plausibility, Replace steer component. |
No release |
Error | Description | Component | Display text | Cause / Action | Effect |
45 | Too many pulses from steering set point device Intermittent contact or perturbing radiation.
More than 255 pulses identified within 100ms |
L,I5 | STEERING WHEEL | Check wire connection, replace sensor bearing; replace component | |
46 | Steering set point device wrongly connected AS4803L: More than 3 pulses identified in one direction and more than 3 pulses in another within 100ms. | L,I5 | STEERING WHEEL | Check sensor bearing connection; check wire connection AS4803L: Check steering wheel recognition input. | |
47 | No pulses from steer set point device ETVQ steering wheel no pulses from 1st sensor bearing. More than 10 pulses were obtained from the stepper motor but fewer than 3 pulses were counted within 200ms from the sensor bearing. | L,I5 | STEERING WHEEL | Check wire connection, replace sensor bearing; replace component | No release |
Error | Description | Component | Display text | Cause / Action | Effect |
48 | Does not match the “Steering type” parameter ETVQ steering wheel no pulses from stepper motor or 2nd sensor bearing.
More than 10 pulses were obtained from the sensor bearing but fewer than 2 pulses were counted within 200ms from the stepper motor sensor bearing. |
L | STEERING TYPE | Set steering type correctly
ETVQ: Check stepper motor coupling, tighten grub screw. Test both setpoint device branches, set defaults and truck type Otherwise faulty, replace component. |
|
49 | CAN supply interrupted; Supply above 14 volts or less than 10 volts, Can or sensor bearing incorrectly
supplied |
AS 2412 F,H-AC | Can Bus CAN supply | Suply on CAN connector greater than 14 volts (electrical system short circuit, component) | Travel disabled |
50 | NRG Multipilot wire breakage Horizontal tilt | M | Setpoint device horizontal | Check Multipilot wire connection Parameter 540 set to 1 by mistake | Travel and lifting disabled. |
51 | Teach-In: steering actual value potentiometer | L | Incorrect setting SETTING | Repeat calibration, check wire connection;check potentiometer;replace component | |
52 | Teach-In: Brake magnet potentiometer | L | Incorrect setting SETTING | Repeat calibration, check wire connection;check potentiometer;replace component | |
53 | Teach-In: Steering setpoint potentiometer | L | Incorrect setting SETTING | Repeat calibration, check wire connection;check potentiometer;replace component |
Error | Description | Component | Display text | Cause / Action | Effect |
54 | Motor wire breakage during power-up test ETVQ: Temperature voltage level less than 0.3 volts or greater than 2.7
volts |
L, F, H | MOTOR WIRE BREAKAGE | Check wire connection;
Check temperature sensor lines; replace component; replace motor |
|
55 | Motor short circuit; Current not ok; Power stage faulty | L, F-AC, H-AC | SHORT CIRCUIT MOTOR | Check wire connection; Replace motor; Replace component | Traction motor stops, Hydraulic motor stops Warning symbol
flashing (Else-Check). |
56 | Motor or actual value transmitter incorrectly connected | L,F.H | MOTOR REVERSE POLARITY | Check motor connection; check actual value transmitter potentiometer; AC: Phases L1,L2 or L3 swapped on motor; | |
57 | No actual value change Motor turns despite control signal | L,F,H | Steering controller ACTUAL VALUE TRANSMITTER | Check motor; check actual angle potentiometer; rectify mechanical wheel block;
AS4803L: Check incremental bearings; replace component; AC: Check actual value transmitter wire breakage signals PM2402L check operating mode |
|
58 | Steering angle actual value fluctuates
ETVQ: Reference mark 0° could not be started within 5 seconds or no valid segment reached. Steer motor does not turn |
L | STEER ACTUAL ANGLE | Check actual value transmitter (on steer motor)
Check steer motor, fuse and incremental bearing, rectify mechanical wheel block; Check proximity switch distance. |
Error | Description | Component | Display text | Cause / Action | Effect |
59 | Steering angle nominal value fluctuates | L | Steer angle setpoint device
TILLER POTENTIOMETER |
Check setpoint device potentiometer (on tiller) | |
60 | Swivelling bolster does not follow steering wheel directions
Deviation of > 15° for 100ms The wheel turns more than 5°without change of nominal value on steering wheel, less than 2°/sec after reaching the nominal position. Tyres over-tensioned, the actual value cannot follow the nominal value. |
L | STEERING CONTROL | Check steering bolster mechanics; check chain and chain tension; check motor; check actual value transmitter attachment;
Check tyres, replace wheel if necessary. |
|
61 | Power stage error | L | CONTROLLER | Replace controller | |
62 | Power stage error | L | CONTROLLER | Replace controller | |
63 | Sensor power supply out of range
AS4803L: < 10V oder >16V |
L,F-AC,H-AC | CONTROLLER | The 12 volt supply not in valid range. Monitoring of 12 volt sensor supply greater than 15 volts and less than 11 volts.
Switch controller off and on, replace fuse and controller if necessary. |
|
64 | Software version differs | L | CONTROLLER | Different software versions in the AS4803Ls in the ETV-Q. Update software to same level. |
Error | Description | Component | Display text | Cause / Action | Effect |
65 | NRG Multipilot wire breakage centre shifter | M | Centre switch MP centre shifter | Check Multipilot wire connection Parameter 540 set to 1 by mistake | Travel and lifting disabled. |
66 | NRG Multipilot wire breakage
180° / 360° steering toggle |
M | 180-360 switch
MP toggle switch 180°/ 360° |
Check Multipilot wire connection Parameter 543 set to 1 by mistake | Travel and lifting disabled. |
67 | NRG-Multipilot setpoint device travel direction switch jams on MP when system starts | M | Travel direction MP setpoint device | Check Multipilot switch, values in Judit MP teach window, recalibrate values | Travel and lifting disabled. |
68 | Safety switch wire breakage | I2, I3, I4, I5 | DEADMAN | Check wire connection to safety switch (deadman, seat switch); replace safety switch | |
69 | Both lift and lower requested simultaneously | I2, I5, FS | LIFT/LOWERSWITCH | Check wire connection; check switch | |
70 | Component fails to respond orresponds incorrectly to self test | F-AC, H-AC, M, S, A,
I2, C |
SELF TEST | Check displays on basic component (LED); note other error messages on basic card; Check wireconnectionsandcheck connector; check power supply behind the main contactor contact, in the event of an error the voltage will be much lower here than the rated operating voltage. Disconnect the positive supply from the components to target the error cause. One component overloads the testing voltage due to internal short circuit.
The testing voltage arises by charging the internal capacitor batteries via a resistor to the level of the control voltage supply. |
No travel, hydraulics Warning symbol
Flashing warning (Else-Check). |
Error | Description | Component | Display text | Cause / Action | Effect |
71 | Lower potentiometer wire breakage | I2, FS | LOWER POTENTIOMETER | Check wire connection; replace lower potentiometer; replace Multipilot; replace interface | |
72 | No lowering zero position | I2, FS | LOWER RESTPOSITION | Warning, check lower setpoint device | |
73 | Valve output interface faulty | I2 | VALVE OUTPUT | Warning, check valve outputs | |
74 | Interface valve output faulty | I2 | INTERFACE FAULTY | Replace interface | |
75 | Proportional valve does not draw any current Correct Multipilot ?? | I2,I4,C | PROP. VALVE | Check wire connection, replace proportional valve;replace Canion / interface; replace proportional valve | Flashing warning symbol (Else- Check). |
76 | Proportional valve short circuit | I2, I4C | PROP. VALVE | Check wire connection, replace proportional valve;replace Canion / interface; replace proportional valve | Flashing warning symbol (Else- Check). |
77 | Button wire breakage | I2, | BUTTON WIRE BREAKAGE | Check wire connection; replace button; replace interface | |
78 | Button and travel switch pressed simultaneously | I2 | BUTTON / TRAVEL SWITCH | Warning: Check wire connection; replace button; replace interface | |
79 | Switch and deadman switch pressed simultaneously | I2 | BUTTON / DEADMAN | Warning: Check wire connection; replace button; replace interface | |
80 | 2 travel directions simultaneously | I2 | ELECTRICAL SYSTEM | Check wire connection; replace button; replace interface | |
81 | Different parameters for the two traction controllers | F, F-AC | MOTORS | reset parameters (EFG traction controllers) | Travel inhibited |
82 | Sensor wire breakage | I2 | ELECTRICAL SYSTEM | Safety height: Check wire connection; replace button; replace interface |
Error | Description | Component | Display text | Cause / Action | Effect |
83 | 2 of the same components report on the truck
e.g. AS4803L: Key switch voltage cannot be assigned to components Elle_1,Elle_2 or Elle_3 |
F, H, I4, F-AC L-AC | ELECTRICAL SYSTEM | Check component encoding; check wire connection; replace component; | Travel inhibited |
84 | Faulty speed sensor:
à AS4803L: – Speed changes by 50% within 4ms; – Reference speed less than half the rated speed; – Steer transmission blocked; – Tear identification: a valid sensor reading is reduced to zero within 4ms and remains at this level for 50ms without producing a new valid reading. à PM2402L/2 from V1.60: – Too many pulses on encoder 3 on steer motor |
F,H,L-AC | SPEED SENSOR | Check speed sensor; Sensor bearing drift; Check wire connection; Replace speed sensor; Replace component;
Check wire routing, do not route together with motor supply wires! |
Travel stop, Lift stop,
Flashing warning symbol (Else- Check), hydraulic functions enabled. |
85 | Power release low voltage Travel/Steer:
Capacitor voltage drops to 30V (48V) for 0.5 seconds |
F,H-AC L-AC | ELECTRICAL SYSTEM TRAVEL | Switch truck on and off; check battery; check battery cable connections; check fuse;
Check power connections; replace component |
Travel, hydraulics no function, warning symbol
Flashing warning (Else-Check). |
Error | Description | Component | Display text | Cause / Action | Effect |
86 | Improbable speed, sudden change:
à AS4803L: 2 sensor systems differ from each other. à PM2402L/2 from V1.60: Encoders 3 and 4 supply different sensor signalse |
F,H-AC L-AC | SPEED IMPLAUS | Check wire connection; Replace speed sensor; Replace component;
Pulse counts correct: 8 or 64 pulses/ revolution? Check wiring and plug connections, check wire routing, do not route together with motor supply wires! |
|
87 | Sensor line interrupted AS4803L: no voltage drop on a 100 Ohm internal measurement resistor MFC brake: load wheel
speed sensing |
F-AC L-AC
MFC brake |
Electrics DISCONNECTION SENSOR BEARING | Sensor wire disconnected, motor consumes maximum current and makes buzzing noise. Check sensor wires. | |
88 | Hydraulic speed sensor faulty on AS4814H | H (AS4814H) | SPEED SENSOR H | Check speed sensor;
Check wire connection; replace speed sensor; replace component; |
Hydraulics stop,
Flashing warning symbol (Else- Check), travel enabled. |
89 | Hydraulics power release low voltage | H | ELECTRICS- HYDRAULICS | Check battery, check battery wire connection;
Check fuse; replace component |
Reduced power for travel and lifting.
Warning symbol flashing (Else-Check). |
90 | Travel with handbrake on | C | ELECTRICAL SYSTEM | Check magnetic brake switch | Flashing warning symbol (Else- Check). |
91 | 24 volts out of range Info at <17 V
Err at <15 V |
C | ELECTRICAL SYSTEM | Check power supply; check wire connection | For a warning, only the warning symbol flashes (Else-Check).
For an error, the truck stops. |
Error | Description | Component | Display text | Cause / Action | Effect |
92 | Wrong component reporting on Canion | M, S, A | ELECTRICAL SYSTEM | Check Master/Solopilot; check display; replace component
Check jumper in XB 27 and XB 44 from pin 2 to pin 6, |
Travel, lifting
function, warning symbol flashes (Else-Check). |
93 | ACS capacitors not charged | F, H, C | ELECTRICAL SYSTEM | Check charging connection, main contactor
does not apply, check bus voltage, check transformer, fuses and cable set, Replace component |
Travel, lifting no function, warning symbol flashes (Else-Check). |
94 | SDO error | F, H, C | SDO ERROR | Software incompatible check software version
Reload software. Check jumper in XB 41 from pin 12 to pin 13. |
Travel, lifting no function, warning symbol flashes (Else-Check). |
95 | Pin code error | C | PIN CODE ERROR | Component pin codes not identical | Travel, lifting no function, warning symbol flashes (Else-Check). |
96 | No zero position for hydraulics Masterpilot, Solopilot, | M,S | Hydraulics zero position MP/SOLOPILOT | Check Master/Solopilot; lift, lower, tilt, ZH1, ZH2, ZH3, horn switch not in zero position
Replace component |
Hydraulic functions stop, “Warning” symbol flashes (Else-Check), travel enabled |
97 | Segment beyond tolerance limits
à PM2402L/2 from V1.60: Referencing error on power up, no switch signal from proximity switch (NS) or time interval exceeded |
L | FAULTY SEGMENT | Segment on swivelling bolster not within tolerance level.
Check wiring and proximity switch, check distance from switch to trip cam on swivelling bolster |
Error | Description | Component | Display text | Cause / Action | Effect |
98 | The position of the sensor bearing and proximity switch (segment) deviate by more than 1.1 degrees. When the truck starts up, the direction of rotation from the steering wheel sensor system to the motor power connection or the steer motor sensor system is inversed.
à PM2402L/2 from V1.60: Referencing error during operation, unexpected switch signal from proximity switch. |
L | POSITION DEVIATION | Check wiring.
Check wiring and proximity switch, check distance from switch to trip cam on swivelling bolster |
|
99 | CANBus damaged; CANBus driver temporarily deactivated | F,H,M,S,A, I3, I4, C | CAN-BUS | Check wire connection, check terminal resistors, install truck anti- interferencemeasures; | Travel, hydraulics no function, warning symbol flashes (Else-Check). |
100 | NRG software versions of internal component parts
implausible |
M | Multipilot software | Replace component part with corresponding component, as flashing currently not possible in the
field. |
Error | Description | Component | Display text | Cause / Action | Effect |
101 | Input / output error | JUBES | Jubes input/output | Check I/Oa, rectify contact error, check operating voltage, replace external transmitter
Index info in display: a— Sensor 1 supplies values, but not defined. Check parameters 11-17 b— Sensor 2 supplies values, but not defined. Check parameters 20-26 c— Sensor 3 supplies values, but not defined. Check parameters 29-35 Or a sensor 1-3 supplies a voltage outside the range of 0.5V – 9.5V. |
Shown in the driver’s display with error 101 |
102 | Internal error | JUBES | Jubes internal | Check operating voltage. Index info in display:
a — Communication between access module and data recording faulty, check connection e — Radio module faulty f — Radio channel number is “0”, should be >0, check parameter 100 g — Radio transmitting power is “0”, Check parameter 101 h — Lock number is invalid, replace access module i — Impact sensor faulty, replace data recorder |
Shown in the driver’s display with error 102 |
Error | Description | Component | Display text | Cause / Action | Effect |
103 | Parameter error | JUBES | Jubes parameters | Set parameters Index info in display:
a — Parameter 5 greater than parameter 6, should be smaller. b — Differential value of parameter 11 is greater than the differential values of the various stages of parameters 12-17 c — Differential value of parameter 20 is greater than the differential values of the various stages of parameters 21-26 d — Differential value of parameter 29 is greater than the differential values of the various stages of parameters 30-35 e — the stages of parameters 12-17 … f — the stages of parameters 21-26 … g — the stages of parameters 30-35 … h — Impact stages of parameters 47-49 … i — Impact stages of parameters 50-52 … …are not in increasing order |
Shown in the driver’s display with error 103 |
104 | Sensor bearing provides
no pulses on system start up |
F,H | (SENSOR BEARING) | Check sensor bearing and wire, replace sensor bearing or
controller |
|
105 | Motor temperature gauge
provides incorrect values Sensor line wire breakage |
F,H,L | Temp.Motor | Check sensor connection and lines, if
possible replace sensor, otherwise replace the entire motor… |
|
106 | Controller temperature gauge provides incorrect
values |
F,H,L | Temp. controller | Internal error, replace controller. |
Error | Description | Component | Display text | Cause / Action | Effect |
107 | Key switch voltage out of range
Hardware encoding incorrect |
F,H,L
MFC hydr. MFC brake |
Electrics | Error in controller connection (Saab connector) on component | No travel No lifting No steering
Main contactor open |
108 | Calibration reading incorrect | F,H | (CONTROLLER
internal) |
Internal error, replace controller. | |
109 | Brake pedal faulty | MFC brake | BRAKE PEDAL | Brake pedal signals implausible | |
110 | Current output faulty | MFC brake MFC hydr. MFC option | CONTROLLER | Check outputs for short circuits | MFC_Hydr.: no lifting MFC_Brake: crawl speed only |
111 | Steering controller is monitored by traction controller for signs of life telegrams
Traction controller does not receive these telegrams. The Can Bus is overloaded. |
F | Steering controller | Check steering controller | Travel inhibited Main contactor open |
112 | Steering controller_2 is monitored by traction controller_1 for signs of life telegrams
The Can Bus is overloaded. |
F | Traction controller | Check Can Bus, measure terminal resistor 60Ohm | |
113 | Lift controller does not send lift telegrams | H | LIFT CONTROLLER | ||
114 | No traverse distance reference on power up | MFC hydr. | Info 32
Traverse reference |
None | Reduced traverse speed until both stops have been reached once. |
Error | Description | Component | Display text | Cause / Action | Effect |
115 | Main contactor improbable,
contacts not closed. Wire connection interrupted, faulty main contactor driver on traction controller |
F,H,L
?? |
Main contactor improbable | Check wire connection.
If error 19 is also present, disconnect the shorted power stage Disconnect the power positive. Check driver voltage (switched against negative). If reading OK, check contactor coil and mechanics. |
No truck functions |
116 | After software flashing (field operation), the item number of the software is implausible and parameters may also be implausible. | F,H,
MFC brake MFC prop |
Info 54
SET TRUCK TYPE |
Set truck type and switch truck off / on (wait approx. 35 seconds).
On request, automatically: all parameters are set to default, the software item number is set to plausible, the log book is deleted, the hourmeter set to zero and entry 116 made in the log book. |
In the log book only error 116 stands as a marker for this process and all parameters can be at default. |
117 | Cab position implausible, rotary potentiometer value does not match 180
degree switch |
CANION | Cab position | Check rotary potentiometer, re-adjust if necessary, check 180 degree switch | No TRAVEL release |
118 | Steering controller reports error | L | Steering controller | Check display on steering controller | TRAVEL inhibited, EMERGENCY STOP activated |
119 | Weigher button faulty | MFC brake | Button faulty | Check wire and button | Weighing interrupted |
120 | Weigher pressure sensor faulty | MFC hydraulics | Sensor faulty | Check wire and sensor | Weighing interrupted |
121 | Battery incorrectly locked | F-AC | Battery lock | Locking strips stuck. Check proximity switch | No truck functions |
201 | Optical sensor faulty | Rack height select | sensor |
Error | Description | Component | Display text | Cause / Action | Effect |
202 | Too many reference points during calibration | Rack height select | Calibration wrong | ||
203 | Sensor evaluation improbable | Rack height select | sensor | ||
204 | Error when reading EEPROM | Rack height select | Controller | All settings set to default | |
205 | No Multipilot in truck | Rack height select | MP missing | ||
240 | Internal process interrupted | Rack height select | Controller | ||
250 | No height actual value on job input | Rack height select | The height is invalid for the warehouse level entered | ||
252 | Rack height select incorrect | Rack height select | |||
253 | Rotary field implausible –
transmission overloaded, excess load on incline |
F | Controller | None, switch truck off/on | Main contactor opened |
254 | Diagnostics piratry | Judit Box | None | Create authorisation | No diagnosis possible |
Components
A | C = 064 | Display / Operation (LISA / JULIA) |
C = 065 | Display / Operation (Else-Check) | |
C = 066 | Display/Operation (CANCode) | |
C = 067 | Display (CANDis) | |
C = 068 | Display/Operation (on board computer) | |
C = 3 | Comfort display [CANopen] | |
C | Canion (Atlas Copco) [CANopen] | |
C = 1 | – Master | |
C = 11 | – Slave | |
F | C = 016 | Travel (MP1510C / AS2405F / AS2409K / AS2412F) |
C = 016 | Travel 1 (MP1514F / AS4814Fplus) | |
C = 017 | Travel 2 (MP1514F / AS4814Fplus) | |
F-AC | C = 016 | Travel (AS4812/14F) |
C = 8 | ACS Traction (Atlas Copco AC 8011/18, Inmotion) [CANopen] | |
Travel switch | C = 096 | Can-Bus travel switch |
H | C = 032 | Lift (MP1514H / AS4814Hplus) |
H-AC | C = 032 | Lift (AS4814H) |
C = 7 | ACS Pump (Atlas Copco AC 8011/18, Inmotion) [CANopen] | |
Rack height select | C = 128 | Rack Select |
I | C = 21 | I/O-Board 1 [CANopen] |
C = 22 | I/O-Board 2 [CANopen] | |
C = 23 | I/O-Board 3 [CANopen] | |
C = 24 | I/O-Board 4 [CANopen] |
I2 | C = 146 | Interface 2 |
C = 155 | Interface 21 | |
C = 156 | Interface 71 | |
I3 | C = 147 | Interface 3 |
I4 | C = 148 | Interface 4 = MFC_brake |
I5 | C = 149 | Interface 5 |
I6 | C = 150 | Interface 6 = MFC_Prop |
I7 | C = 151 | Interface 7 |
I8 | C = 152 | Interface 8 = MFC_Option |
Jubes | C = 069 | ISM Access Module |
C = 29 | ISM Access Module [CANopen] | |
C = 070 | ISM-Data recorder | |
C = 071 | ISM-radio module | |
L | C = 048 | Steer (MP1502L / PM2402L / AS4803L) |
C = 048 | Steer 1 (AS4803L) | |
C = 049 | Steer 2 (AS4803L) | |
C = 050 | Steer 3 (AS4803L) | |
C = 4 | Steer computer [CANopen] | |
M | C = 096 | Multipilot / Masterpilot |
C = 2 | Multipilot / Solopilot [CANopen] | |
S | C = 112 | Solopilot / Hand lever |
Travel setpoint device: travel potentiometer, accelerator pedal
Steering actual value transmitter: steer potentiometer, proximity switch (on steered wheel)
ONLY in 1st generation!
All messages numbered above 100 come from the interface and correspond to messages 1- xx -99!
Warning / Information Messages | |||||
INFO 01 | SEAT SWITCH_OPEN | ||||
INFO 02 | NO_TRAVEL DIRECTION | ||||
INFO 03 | NO_TRAVEL RELEASE | ||||
INFO 04 | NO_NOMINAL VALUE | ||||
INFO 05 | LIFTING OFF | ||||
INFO 06 | DEADMAN KEY OPEN | ||||
INFO 07 | START_INCORRECT | ||||
INFO 08 | PARKING BRAKE | ||||
INFO 09 | SLOW SPEED | ||||
INFO 10 | TEMPERATURE DRIVE MOTOR | ||||
INFO 11 | TEMP_LIFT_MOTOR | ||||
INFO 12 | TEMP_STEER_MOTOR | ||||
INFO 13 | BRUSH WEAR OUT_DRIVE_MOTOR | ||||
INFO 14 | BRUSH WEAR OUT_LIFT_MOTOR | ||||
INFO 15 | BRUSH WEAR OUT_STEER_MOTOR | ||||
INFO 16 | DRIVING DISABLE | ||||
INFO 17 | LIFT END DIS. | ||||
INFO 18 | SECURITY HEIGHT | ||||
INFO 19 | DOOR OPEN | ||||
INFO 20 | AISLE MODE | ||||
INFO 21 | RESCUE STEERING | ||||
INFO 22 | STEERING MISSING | ||||
INFO 23 | DIAGNOSTIC_MODE | ||||
INFO 24 | SWITCH POWER OFF | ||||
INFO 25 | TEMP_TRAVEL | ||||
INFO 26 | TEMP_LIFT | ||||
INFO 27 | TEMP_STEER | ||||
INFO 28 | SPARE_1 | ||||
INFO 29 | DISPLAY SWITCHES THE EXTERNAL
BUZZER |
INFO 30 | TWIN PEDAL BOTH APPLIED | ||||
INFO 31 | NO ZERO POSITION | ||||
INFO 32 | NO TRAVERSE REFERENCE ON POWER UP | ||||
INFO 33 | ONLY CRAWL SPEED POSSIBLE AS
BATTERY NOT LOCKED |
||||
INFO 34 | ONLY CRAWL SPEED POSSIBLE, AS INFO
FROM STEERING CONTROLLER |
||||
INFO 35 | LOW VOLTAGE TRAVEL | ||||
INFO 36 | LOW VOLTAGE LIFT | ||||
INFO 37 | LOW VOLTAGE STEER | ||||
INFO 40 | CHECK MOTOR SENSOR SYSTEM | ||||
INFO 48 | IMPACT EVENT VERTICAL FORCE 1 | ||||
INFO 49 | IMPACT EVENT VERTICAL FORCE 2 | ||||
INFO 50 | IMPACT EVENT VERTICAL FORCE 3 | ||||
INFO 51 | IMPACT EVENT HORIZONTAL
FORCE 1 |
||||
INFO 52 | IMPACT EVENT HORIZONTAL
FORCE 2 |
||||
INFO 53 | IMPACT EVENT HORIZONTAL
FORCE 3 |
||||
INFO 54 | SET TRUCK TYPE | ||||
INFO 73 | CHECK VALVE OUTPUTS |
- 0915.2 — Industrial truck not ready for operation — battery door opened.
- 0938.1 — Battery discharged (0%).
- 1901.1 — Drive pedal activated during startup.
- 1904.1 — No travel direction present with drive pedal activated.
- 1908.1 — Seat belt or belt lock not closed when the pedal is pressed.
- 1909.1 — Activation of drive pedal when the parking brake is not released.
- 1917.1 — Drive pedal and brake pedal both activated at the same time.
- 1918.1 — Industrial truck ready for operation, but cab door opened.
- 2908.1 — Seat belt or belt lock not closed when hydraulic function is activated.
- 2937.3 — Simulatneous activiation of several hydraulic functions that can only be operated as individual functions.
- 2951.1 — Hydraulic function activated during startup.
- 5409.1 — Battery temperature too high
- 5393.1 — Battery cell faulty
Jungheinrich Service Manual
Jungheinrich DFG/TFG
660-690 Operating Instructions
Models: DFG 670; DFG
680; DFG 690; DFG S80; DFG S90; TFG 660; TFG 670; TFG 680; TFG 690; TFG S80; TFG S90; DFG S90.
Jungheinrich DFG S80
Service Manual
Models: TFG 680; DFG 670; DFG 660; DFG 680; DFG 690; DFG S80; DFG S90; TFG 660; TFG 670; TFG 690; TFG S80; TFG S90.
Jungheinrich DFG TFG
316-435 Operating Instructions
Models: TFG 430; DFG 320; DFG 425; DFG 430; DFG 435; TFG 316; TFG 320; TFG 425; TFG 435.
Jungheinrich EFG-Vac 22-30/ 25L/S/SL Service Manual Download
Jungheinrich ECE 225 (90309857) Spare Parts Catalogue Download
Jungheinrich EJC 110/112 Operating instructions Download
Jungheinrich DFG/TFG 16 — 50 A/B/C-K Operating instructions Download
Jungheinrich DFG 660 Service Manual Download
Jungheinrich DFG 670 Service Manual Download
Jungheinrich DFG S80 Service Manual Download
Jungheinrich DFG_TFG 316-435 Operating Instructions Download
Jungheinrich ECE 225 Spare Parts Catalogue Download
Jungheinrich EFG 213-320 Operating Manual Download
Jungheinrich EFG-Vac 22 Service Manual Download
Jungheinrich EFG-Vac 25L Service Manual Download
Jungheinrich EFG-Vac 30 Service Manual Download
Jungheinrich EJD 220 Service Manual Download
Jungheinrich ERE 120 Service Manual Download
Jungheinrich ETM 214 Service Manual Download
Jungheinrich ETM 216 Service Manual Download
Jungheinrich ETM 325 Service Manual Download
Jungheinrich ETV 214 Service Manual Download
Jungheinrich ETV 216 Service Manual Download
Jungheinrich ETV 318Service Manual Download
Jungheinrich ETV 320 Service Manual Download
Jungheinrich ETV 325 Service Manual Download
Jungheinrich EZS 330 XL Operating Instructions Manual Download
Jungheinrich EZS 350 XL Operating Instructions Manual Download
Jungheinrich SLH 200 Service Manual Download
Jungheinrich TFG 660 Service Manual Download
Jungheinrich Fault Codes
Jungheinrich Fault Codes Download
Jungheinrich EJC112 & E1202 Event Messages Codes List Download
Jungheinrich Error Codes List Download
Jungheinrich Fault Codes Download
Jungheinrich LISTADO ERRORES Download
Jungheinrich System Error Codes list Download
Jungheinrich System Error Codes list Download
Jungheinrich System Error Codes list Download
Jungheinrich forklifts
The manufacturer of forklifts is Jungheinrich, which is a leader in the production and sale of industrial, warehouse and material handling equipment. The company began its journey from 1953, when
a small loader company was founded, and by 2011 the company had several factories at its disposal.
Purpose
Forklifts are mainly used to work in warehouses, but without them they are very rarely managed in large-scale industries. They carry loads that are placed on pallets. Due to the version with a
closed cabin, they are able to work even in places with unfavorable external environment, namely, with wind, dust, sparks, sawdust, steam, and so on.
Electric
Electric loaders are represented by 5 series, which differ in load capacity, low unloading height, technology, maneuverability, as well as convenience of the operator’s workplace.
1 series EFG 110/113/115. The letters mean that this is an electric forklift, the first number indicates the series, and the second two are the maximum carrying
capacity in hundreds of kilograms. These are lightweight and compact loaders that have just one rear wheel. Thanks to these parameters, they have excellent maneuverability and can move even
inside the truck body. However, these «kids» are able to work with a weight of from 1 to 1.5 tons and lift the load to a height of 6.5 meters. AC control electronics may be updated.
EFG 213/215 / 216k / 216 / 218k / 218/220. The index k near some models indicates that the model has a smaller battery, a shorter base and a shorter fork body. This series has
the same dimensions and related benefits. However, the maximum load capacity is increased, as well as equipped with a large number of technologies. In the loader, an electric power steering was
added, the ability to independently configure 5 work programs, replace batteries, a more thoughtful security system, an automatic parking brake, smart electronics, and a maintenance-free brake
system and electric motor. The case in these loaders is integral, which provides greater stability when maneuvering.
EFG 316 / 316k / 318 / 318k / 320. The main differences between these trucks from previous models is that they have 4 wheels and a fully enclosed cab with front and rear window
cleaner. The control system is now electro-hydraulic, which provides better handling. Cab stances were enhanced, and the lighting system and battery compartment received additional protection.
EFG 540k / 540 / 545k / 545/550 / S40 / S30. These are the most powerful and big electric lift trucks. The maximum unloading height has also been increased, but only to 7.18
meters. You can use various packages of additional functions that determine the operation of the loader. In this series, more attention is paid to operator safety, as well as comfort and
ergonomics of the workplace.
-
Меню «Рулетка»
Включает-выключает отсчет «Времени»
и «Пути» от заданной курсором точки
фрагмента. При включении в верхней части
окна появляется надпись «Рулетка
включена», а показания «Время»
и «Путь» обнуляются.
-
Меню «Сетка»
При помощи пункта «Сетка» на окно
аналоговых сигналов наносятся пунктирные
линии:
а) » Скорость » — с шагом 20 км/ч;
б) » Путь » — с шагом 500 м;
в) » Давление » — с шагом 0,05 МПа (0,5
кгс/см²);
г) «Километры» — с шагом 1 км.
Включение требуемой разметки производится
нажатием на соответствующий пункт меню,
выключение – нажатием на пункт «Выкл.».
-
Меню «Доп.Параметры»
Включает-выключает окно дополнительных
служебных сигналов САУТ в правом нижнем
углу (рисунок 35). Дополнительные параметры
разбиты на группы.
Группа 1 включает (по строкам сверху
вниз) следующие значения:
а) L1 — длина первого шлейфа принятая
пультом управления от напольного
устройства, в импульсах ДПС;
б) L12 — расстояние от начала первого
шлейфа до начала второго шлейфа принятое
пультом управления от напольного
устройства, в импульсах ДПС;
Рисунок 35 — Меню «Доп.Параметры »
в) L2 — длина второго шлейфа принятая
пультом управления от напольного
устройства, в импульсах ДПС;
г) Dк — диаметр колеса
ДПС1/ДПС2;
д) Gen: — тип и номер для генератора устройств
САУТ-ЦМ;
е) Mar: — номер маршрута или частота
основного шлейфа генератора для устройств
САУТ-ЦМ;
ё) Qr: — тормозной коэффициент. Если
значения тормозного коэффициента по
полукомплектам САУТ не одинаковы, то
указываются оба значения, через дробь;
ж) фраза или код последней фразы,
произнесенной синтезатором речи.
Группа 2:
а) Dk- диаметр колеса
ДПС1/ДПС2;
б) Lкпт: — расстояние между сменами КПТ;
в) Lпг: — расстояние между
путевыми генераторами;
г) Lпгк: — расстояние между кодированными
путевыми генераторами;
д) Lis: — расстояние коррекции перехода
изостыка (от пропадания КПТ до появления
достоверного КПТ – в импульсах ДПС/16);
е) Pам: — уставка давления от системы
автоведения.
Группа 3 (радиоканал):
СУО:- номер сигнальной установки;
М:- номер маршрута.
Группа 4 (диагностика):
Диагностическая информация САУТ состоит
из кода устройства и кода ошибки,
указанные через точку (рисунок 36).
Рисунок 36 – Диагностическая информация
при равенстве значений полукомплектов
Если диагностическая информация САУТ
различна по полукомлектам, то указывается
информация в обоих полукомплектах,
через дробь (рисунок 37).
Рисунок 37 — Диагностическая информация
при отличии значений полукомплектов
Коды устройств:
00 — Резерв
01 — БС-ДПС
02 — Пульт машиниста первой кабины
03 — Пульт машиниста второй кабины
06 — Пульт управления первой кабины
07 — Пульт управления второй кабины
08 — Блок коммутации первой кабины
09 — Блок коммутации второй кабины
10 — БС-АЛС, БС-КЛУБ, БС-ЕКС.
11 — БС-ЦКР
12 — Регистратор параметров САУТ
13 — Проверочный прибор САУТ
14 — БС-МСУД, Блоки связи с системами
управления локомотива
15 — Модуль Центрального процессора САУТ
Коды ошибок устройств:
Общие ошибки
01 — Нет связи с устройством, которое
должно быть в данной конфигурации
02 — Ошибка контрольной суммы идентификационной
информации
устройства.
03 — Несоответствие Модификации устройства
04 — Не соответствие Модернизации
устройства
05 — Несоответствие Модификации и
Модернизации устройства
06 — Версия рабочей программы устройства
устарела
07 — Версия рабочей программы устройства
устарела и
несоответствие Модификации устройства
08 — Версия рабочей программы устройства
устарела и
несоответствие Модернизации
устройства
09 — Версия рабочей программы устройства
устарела и
несоответствие Модификации и
Модернизации устройства
Дополнительная информация:
Коды ошибок БС-ДПС
10 — Ошибка чтения EEPROM БС-ДПС
11 – Неисправность первого ДПС
12 – Неисправность второго ДПС
13 – Неисправность первого и второго
ДПС
14 — Один или оба ДПС имеют направление
назад при движении вперед
Коды ошибок пульта управления
10 – Ошибка обнаружения датчика давления
(неисправность или его
отсутствие)
11 – Пульт управления не откалиброван
(начиная с 18 версии ПУ)
Коды ошибок БС-АЛС
10 – В карточке установлен КЛУБ-У, а к
системе подключен БС-АЛС
11 – В карточке не установлен КЛУБ-У, а
к системе подключен БС-КЛУБ
12 – В карточке не установлен признак
ЕКС, к системе подключен БС-ЕКС
13 – В карточке не установлен КЛУБ-У, к
системе подключен БС-ЕКС
Коды ошибок БС-ЦКР
10 – Ошибка обнаружения датчика давления
(неисправность или его отсутствие)
Коды ошибок РПС
10 – Ошибка корректировки времени
КИО-САУТ (превышение количества дней в
месяце, с учетом високосного года при
ручном вводе времени с пульта машиниста
САУТ)
* Ошибка возникает на 5 с после ввода.
Коды ошибок модуля МП (адрес 15)
1 – Количество ошибок в линии связи
превышает 30 в мин.
2 – Ошибка CRC базы данных общая
3 – 1 и 2 ошибки вместе
4 – Ошибка CRC таблицы перегонов (проверяется
при включении)
5 – Ошибка 1 + ошибка 4
6 – Ошибка 2 + ошибка 4
7 – Ошибка 1 + ошибка 2 + ошибка 4
8 – Разрушение ОЗУ постоянных параметров
16 – Отсутствие связи с МП БЭК при работе
с КИО-САУТ
Все ошибки KIA BONGO, CARENS, CARNIVAL, CEED, CEED GT, CERATO, CERATO KOUP, MAGENTIS, MOHAVE, OPIRUS, OPTIMA, PICANTO, PRIDE, QUORIS, RIO, SORENTO, SORENTO PRIME, SOUL, SPECTRA, SPORTAGE, VENGA
Ошибки KIA по протоколу OBDI. Самодиагностика.
Двузначные коды
02 – Датчик угла поворота коленчатого вала – нет сигнала
03 – Датчик фазы (датчик распредвала) – некорректный сигнал / нет сигнала
07 – Неверный монтаж колеса угловых меток коленвала
08 – Датчик расхода воздуха
09 – Датчик температуры охлаждающей жидкости
10 – Датчик температуры всасываемого воздуха
12 – Датчик положения дроссельной заслонки
14 – Датчик атмосферного давления
15 – Датчик кислорода (лямбда-зонд)
16 – Датчик положения клапана EGR
17 – Система обратной связи
18 – Форсунка №1 – неисправность электрической цепи
19 – Форсунка №2 – неисправность электрической цепи
20 – Форсунка №3 – неисправность электрической цепи
21 – Форсунка №4 – неисправность электрической цепи
24 – Реле топливного насоса – неисправность электрической цепи
25 – Электромагнитный клапан регулятора давления топлива
26 – Клапан аккумулятора паров топлива. (Purge Control Solenoid Valve)
28 – Клапан рециркуляции отработавших газов – неисправность электрической цепи
34 – Клапан регулятора холостого хода
35 – Неисправность форсунки
36 – Повреждение датчика расхода воздуха
37 – Негерметичность системы впуска
41 – Электромагнитный клапан системы зарядки с переменной инерцией – неисправность клапана / неисправность электрической цепи
46 – Реле кондиционера (A/C) – неисправность электрической цепи.
48 – Клапан продувки EGR – неисправность клапана / неисправность электрической цепи (либо внутренняя неисправность модуля ЕСМ)
49 – Клапана регулятора холостого хода – неисправность клапана / неисправность электрической цепи (либо внутренняя неисправность модуля ЕСМ)
56 – Клапан регулятора холостого хода – неисправность электрической цепи
57 – Входной сигнал компрессора кондиционера – короткое замыкание или неисправность электрической цепи
73 – Датчик числа оборотов двигателя
87 – Лампа индикации неисправности CHECK ENGINE – неисправность электрической цепи
88 – Неисправность ППЗУ блока управления
99 – Аккумуляторная батарея
Ошибки KIA по протоколу OBDII
Топливная система и воздухоподача
P0000-P0099, P0100-P0199, P0200-P0299
P0000 – Неисправностей не обнаружено
P0001 – Управление регулятором подачи топлива — обрыв цепи
P0002 – Управление регулятором подачи топлива — параметры цепи
P0003 – Управление регулятором подачи топлива — низкое напряжение
P0004 – Управление регулятором подачи топлива — высокое напряжение
P0005 – Клапан отсечки подачи топлива — обрыв цепи
P0006 – Клапан отсечки подачи топлива — низкий уровень сигнала
P0007 – Клапан отсечки подачи топлива — высокий уровень сигнала
P0011 – Положение распределительного вала, впуск/левый/передний, банк 1 — слишком ранний угол открывания клапанов / нарушение функционирования системы
P0012 – Положение распределительного вала, впуск/левый/передний, банк 1 — слишком поздний угол открывания клапанов
P0014 – Привод системы изменения фаз газораспределения, выпуск/правый/задний, банк 1 — слишком ранний угол открывания / функционирование системы
P0016 – Положение коленчатого и распределительного валов, банк 1, датчик А — нет соответствия
P0017 – Положение коленчатого и распределительного валов, банк 1, датчик В — корреляция
P0019 – Положение коленчатого и распределительного валов, банк 2, датчик B — корреляция
P0030 – Подогреваемый кислородный датчик 1, банк 1, управление нагревателем — неисправность электрической цепи
P0031 – Подогреваемый кислородный датчик 1, банк 1, управление нагревателем — низкое напряжение цепи
P0032 – Подогреваемый кислородный датчик 1, банк 1, управление нагревателем — высокое напряжение цепи
P0036 – Подогреваемый кислородный датчик 2, банк 1, управление нагревателем — неисправность электрической цепи
P0037 – Подогреваемый кислородный датчик 2, банк 1, управление нагревателем — низкое напряжение цепи
P0038 – Подогреваемый кислородный датчик 2, банк 1, управление нагревателем — высокое напряжение цепи
P0042 – Подогреваемый кислородный датчик 3, банк 1, управление нагревателем — неисправность электрической цепи
P0043 – Подогреваемый кислородный датчик 3, банк 1, управление нагревателем — низкое напряжение цепи
P0044 – Подогреваемый кислородный датчик 3, банк 1, управление нагревателем — высокое напряжение цепи
P0068 – Датчик абсолютного давления во впускном коллекторе/датчик расхода воздуха (MAF) — несоответствие положению дроссельной заслонки
P0069 – Датчик абсолютного давления во впускном коллекторе / датчик атмосферного давления — корреляция
P0075 – Электромагнитный клапан управления впускными клапанами, банк 1 — неисправность электрической цепи
P0076 – Электромагнитный клапан управления впускными клапанами, банк 1 — низкое напряжение цепи
P0077 – Электромагнитный клапан управления впускными клапанами, банк 1 — высокое напряжение цепи
P0078 – Электромагнитный клапан управления выпускными клапанами, банк 1 — неисправность электрической цепи
P0079 – Электромагнитный клапан управления выпускными клапанами, банк 1 — низкое напряжение цепи
P0080 – Электромагнитный клапан управления выпускными клапанами, банк 1 — высокое напряжение цепи
P0087 – Давление в системе / в топливном коллекторе — слишком низкое
P0088 – Давление в системе / в топливном коллекторе — слишком высокое
P0093 – Значительная утечка в топливной системе
P0094 – Незначительная утечка в топливной системе
P0095 – Датчик 2 температуры воздуха на впуске — неисправность электрической цепи
P0096 – Датчик 2 температуры воздуха на впуске — диапазон/функционирование
P0097 – Датчик 2 температуры воздуха на впуске — низкий уровень входного сигнала
P0098 – Датчик 2 температуры воздуха на впуске — высокий уровень входного сигнала
P0100 – Датчик расхода воздуха (массового — MAF) / (объемного — VAF) — неисправность электрической цепи
P0101 – Датчик расхода воздуха (MAF) / (VAF) — диапазон/функционирование
P0102 – Датчик расхода воздуха (MAF) / (VAF) — низкий уровень входного сигнала
P0103 – Датчик расхода воздуха (MAF) / (VAF) — высокий уровень входного сигнала
P0106 – Датчик абсолютного давления во впускном коллекторе/датчик атмосферного давления — диапазон/функционирование
P0107 – Датчик абсолютного давления во впускном коллекторе/датчик атмосферного давления — низкий уровень сигнала
P0108 – Датчик абсолютного давления во впускном коллекторе/датчик атмосферного давления — высокий уровень сигнала
P0110 – Датчик температуры воздуха на впуске — неисправность электрической цепи
P0111 – Датчик температуры воздуха на впуске — диапазон/функционирование
P0112 – Датчик температуры воздуха на впуске — низкий уровень сигнала
P0113 – Датчик температуры воздуха на впуске — высокий уровень входного сигнала
P0115 – Датчик температуры охлаждающей жидкости — неисправность электрической цепи
P0116 – Датчик температуры охлаждающей жидкости — диапазон/функционирование
P0117 – Датчик температуры охлаждающей жидкости — низкий уровень сигнала
P0118 – Датчик температуры охлаждающей жидкости — высокий уровень входного сигнала
P0120 – Датчик А положения дроссельной заслонки / датчик А положения педали акселератора — неисправность электрической цепи
P0121 – Датчик А положения дроссельной заслонки / датчик А положения педали акселератора — диапазон/функционирование
P0122 – Датчик «А» положения дроссельной заслонки / датчик «А» положения педали акселератора — низкий уровень сигнала
P0123 – Датчик А положения дроссельной заслонки / датчик А положения педали акселератора — высокий уровень сигнала
P0128 – Термостат системы охлаждения — температура охлаждающей жидкости ниже температуры открывания термостата
P0130 – Кислородный датчик 1, банк 1 — неисправность электрической цепи
P0131 – Кислородный датчик 1, банк 1 — низкое напряжение
P0132 – Кислородный датчик 1, банк 1 — высокое напряжение
P0133 – Кислородный датчик 1, банк 1 — малое быстродействие
P0134 – Кислородный датчик 1, банк 1 — нет отклика
P0135 – Подогреваемый кислородный датчик 1, банк 1, управление нагревателем — неисправность электрической цепи
P0136 – Кислородный датчик 2, банк 1 — неисправность электрической цепи
P0137 – Кислородный датчик 2, банк 1 — низкое напряжение
P0138 – Кислородный датчик 2, банк 1 — высокое напряжение
P0139 – Кислородный датчик 2, банк 1 — малое быстродействие
P0140 – Кислородный датчик 2, банк 1 — нет отклика
P0141 – Подогреваемый кислородный датчик 2, банк 1, управление нагревателем — неисправность электрической цепи
P0170 – Топливный баланс, банк 1 — неисправность
P0171 – Слишком бедная топливовоздушная смесь, банк 1
P0172 – Слишком богатая топливовоздушная смесь, банк 1
P0190 – Датчик давления в топливном коллекторе — неисправность электрической цепи
P0191 – Датчик давления в топливном коллекторе — диапазон/функционирование
P0192 – Датчик давления в топливном коллекторе — низкий уровень сигнала
P0193 – Датчик давления в топливном коллекторе — высокий уровень входного сигнала
P0200 – Форсунка — неисправность электрической цепи
P0201 – Форсунка 1 — неисправность электрической цепи
P0202 – Форсунка 2 — неисправность электрической цепи
P0203 – Форсунка 3 — неисправность электрической цепи
P0204 – Форсунка 4 — неисправность электрической цепи
P0205 – Форсунка 5 — неисправность электрической цепи
P0206 – Форсунка 6 — неисправность электрической цепи
P0218 – Перегрев коробки передач
P0220 – Датчик В положения дроссельной заслонки / датчик В положения педали акселератора — неисправность электрической цепи
P0221 – Датчик В положения дроссельной заслонки / датчик В положения педали акселератора — диапазон/функционирование
P0222 – Датчик В положения дроссельной заслонки / датчик В положения педали акселератора — низкий уровень входного сигнала
P0223 – Датчик В положения дроссельной заслонки / датчик В положения педали акселератора — высокий уровень входного сигнала
P0230 – Реле топливного насоса — неисправность электрической цепи
P0231 – Реле топливного насоса — низкое напряжение цепи
P0232 – Реле топливного насоса — высокое напряжение цепи
P0233 – Реле топливного насоса — ненадежный контакт электрической цепи
P0234 – Давление турбонаддува — превышен верхний предел
P0251 – Дозатор топлива А, ротор/кулачок/форсунка — неисправность электрической цепи
P0252 – Дозатор топлива А, ротор/кулачок/форсунка — диапазон/функционирование
P0253 – Дозатор топлива А, ротор/кулачок/форсунка — низкий уровень сигнала
P0254 – Дозатор топлива А, ротор/кулачок/форсунка — высокий уровень сигнала
P0298 – Слишком высокая температура моторного масла
P0299 – Турбокомпрессор / приводной нагнетатель — низкое давление наддува
Система зажигания
P0300-P0399
P0300 – Случайные / множественные пропуски зажигания (воспламенения)
P0301 – Цилиндр 1 — пропуски зажигания (воспламенения)
P0302 – Цилиндр 2 — пропуски зажигания (воспламенения)
P0303 – Цилиндр 3 — пропуски зажигания (воспламенения)
P0304 – Цилиндр 4 — пропуски зажигания (воспламенения)
P0305 – Цилиндр 5 — пропуски зажигания (воспламенения)
P0306 – Цилиндр 6 — пропуски зажигания (воспламенения)
P0320 – Датчик положения коленчатого вала / датчик частоты вращения коленчатого вала — неисправность электрической цепи
P0321 – Датчик положения коленчатого вала / датчик частоты вращения коленчатого вала — диапазон/функционирование
P0322 – Датчик положения коленчатого вала/датчик частоты вращения коленчатого вала — нет сигнала
P0323 – Датчик положения коленчатого вала / датчик частоты вращения коленчатого вала — ненадежный контакт электрической цепи
P0325 – Датчик детонации 1, банк 1 — неисправность электрической цепи
P0326 – Датчик детонации 1, банк 1 — диапазон/функционирование
P0327 – Датчик детонации 1, банк 1 — низкий уровень сигнала
P0328 – Датчик детонации 1, банк 1 — высокий уровень входного сигнала
P0335 – Датчик положения коленчатого вала — неисправность электрической цепи
P0336 – Датчик положения коленчатого вала — диапазон/функционирование
P0337 – Датчик положения коленчатого вала — низкий уровень сигнала
P0338 – Датчик положения коленчатого вала — высокий уровень сигнала
P0339 – Датчик положения коленчатого вала — ненадежный контакт электрической цепи
P0340 – Датчик положения распределительного вала A, банк 1 — неисправность электрической цепи
P0341 – Датчик положения распределительного вала A, банк 1 — диапазон/функционирование
P0342 – Датчик положения распределительного вала A, банк 1 — низкий уровень сигнала
P0343 – Датчик положения распределительного вала A, банк 1 — высокий уровень входного сигнала
P0344 – Датчик положения распределительного вала A, банк 1 — ненадежный контакт электрической цепи
Контроль выбросов
P0400-P0499
P0400 – Система рециркуляции отработавших газов (EGR) — неисправность каналов системы
P0401 – Система рециркуляции отработавших газов (EGR) — недостаточный уровень рециркуляции
P0402 – Система рециркуляции отработавших газов (EGR) — чрезмерный уровень рециркуляции
P0403 – Система рециркуляции отработавших газов (EGR) — неисправность электрической цепи
P0404 – Система рециркуляции отработавших газов (EGR) — диапазон/функционирование
P0405 – Датчик положения клапана А системы рециркуляции ОГ (EGR) — низкий уровень сигнала
P0406 – Датчик положения клапана А системы рециркуляции ОГ (EGR) — высокий уровень сигнала
P0420 – Каталитический нейтрализатор, банк 1 — эффективность ниже требуемой
Р0421 – Прогрев каталитического нейтрализатора, банк 1 — эффективность ниже требуемой
P0422 – Основной каталитический нейтрализатор, банк 1 — эффективность ниже требуемой
P0443 – Электромагнитный клапан аккумулятора паров топлива — неисправность электрической цепи
P0444 – Электромагнитный клапан аккумулятора паров топлива — обрыв цепи
P0445 – Электромагнитный клапан аккумулятора паров топлива — короткое замыкание
P0446 – Система улавливания паров топлива, управление продувкой — неисправность электрической цепи
P0447 – Система улавливания паров топлива, управление продувкой — обрыв цепи
P0448 – Система улавливания паров топлива, управление продувкой — короткое замыкание
P0449 – Система улавливания паров топлива, клапан управления продувкой — неисправность электрической цепи
P0489 – Система рециркуляции отработавших газов (EGR) — низкое напряжение цепи
P0490 – Система рециркуляции отработавших газов (EGR) — высокое напряжение цепи
Контроль скорости и холостого хода
P0500-P0599
P0500 – Датчик скорости автомобиля — неисправность электрической цепи
P0501 – Датчик скорости автомобиля — диапазон/функционирование
P0502 – Датчик скорости автомобиля — низкий уровень сигнала
P0503 – Датчик скорости автомобиля — сигналы хаотичные / пропадающие / высокого уровня
P0504 – Выключатель А/В стоп-сигналов (датчик положения педали тормоза) — корреляция
P0505 – Система управления частотой вращения холостого хода — неисправность
P0506 – Система управления частотой вращения холостого хода — частота вращения ниже допустимой
P0507 – Система управления частотой вращения холостого хода — частота вращения выше допустимой
P0520 – Датчик давления моторного масла — неисправность электрической цепи
P0521 – Датчик давления моторного масла — диапазон/функционирование
P0522 – Датчик давления моторного масла — низкое напряжение
P0523 – Датчик давления моторного масла — высокое напряжение
Электронный блок управления (ЭБУ) и его подсистемы
P0600-P0699
P0600 – Шина данных CAN — неисправность
P0605 – Электронный блок управления двигателем — ошибка памяти ROM
P0615 – Реле стартера — неисправность электрической цепи
P0616 – Реле стартера — низкий уровень сигнала
P0617 – Реле стартера — высокий уровень сигнала
P0620 – Реле стартера — неисправность электрической цепи
P0625 – Вывод обмотки возбуждения генератора — низкий уровень сигнала
P0626 – Вывод обмотки возбуждения генератора — высокий уровень сигнала
P0638 – Управление приводом дроссельной заслонки, банк 1 — диапазон/функционирование
P0650 – Индикатор неисправности (MIL), управление — неисправность электрической цепи
P0670 – Блок управления свечами накаливания — неисправность электрической цепи
P0685 – Реле системы управления двигателем — обрыв цепи
P0686 – Реле системы управления двигателем — низкий уровень сигнала
P0687 – Реле системы управления двигателем — короткое замыкание на массу
P0688 – Реле системы управления двигателем — короткое замыкание на «+»
Трансмиссия
P0700-P0799, P0800-P0899, P0900-P0999
P0700 – Управление АКПП, запрос неисправностей (MIL) — неисправность электрической цепи
P0704 – Концевой выключатель (датчик положения) педали сцепления — неисправность электрической цепи
P0705 – Датчик положения селектора АКПП, входной сигнал PRNDL — неисправность электрической цепи
P0706 – Датчик положения селектора КПП — диапазон/функционирование
P0707 – Датчик положения селектора АКПП — низкий уровень сигнала
P0708 – Датчик положения селектора АКПП — высокий уровень входного сигнала
P0716 – Датчик частоты вращения входного вала АКПП (турбины гидротрансформатора) — диапазон/функционирование
P0717 – Датчик частоты вращения входного вала АКПП (турбины гидротрансформатора) — нет сигнала
P0722 – Датчик частоты вращения выходного вала — нет сигнала
P0727 – Частота вращения коленчатого вала, входной сигнал — нет сигнала
P0731 – 1-я передача — некорректное передаточное отношение
P0732 – 2-я передача — некорректное передаточное отношение
P0733 – 3-я передача — некорректное передаточное отношение
P0734 – 4-я передача — некорректное передаточное отношение
P0735 – 5-я передача — некорректное передаточное отношение
P0741 – Электромагнитный клапан муфты блокировки гидротрансформатора — функционирование или «залипание» в закрытом состоянии
P0742 – Электромагнитный клапан муфты блокировки гидротрансформатора — «залипание» в открытом состоянии
P0743 – Электромагнитный клапан муфты блокировки гидротрансформатора — электрическая неисправность
P0750 – Электромагнитный клапан А переключения передач — неисправность электрической цепи
P0755 – Электромагнитный клапан В переключения передач — неисправность электрической цепи
P0760 – Электромагнитный клапан С переключения передач — неисправность электрической цепи
P0765 – Электромагнитный клапан D переключения передач — неисправность электрической цепи
Другие ошибки
P2020 – Датчик/выключатель положения привода системы изменения геометрии впускного коллектора, банк 2 — диапазон/функционирование
P2096 – Топливный баланс после каталитического нейтрализатора, банк 1 — слишком бедный
P2097 – Топливный баланс после каталитического нейтрализатора, банк 1 — слишком богатый
P2110 – Система управления приводом дроссельной заслонки — принудительное ограничение оборотов
P2118 – Привод дроссельной заслонки, ток электродвигателя — диапазон/функционирование
P2119 – Привод дроссельной заслонки, дроссельная заслонка — диапазон/функционирование
P2158 – Датчик скорости автомобиля B — неисправность электрической цепи
P2159 – Датчик скорости автомобиля B — диапазон/функционирование
P2160 – Датчик скорости автомобиля B — низкий уровень сигнала
P2187 – Слишком бедная топливовоздушная смесь, холостой ход, банк 1
P2188 – Слишком богатая топливовоздушная смесь, холостой ход, банк 1
P2191 – Слишком бедная топливовоздушная смесь, при высокой нагрузке, банк 1
P2192 – Слишком богатая топливовоздушная смесь, при высокой нагрузке, банк 1
P2264 – Датчик наличия воды в топливном фильтре — неисправность электрической цепи
P250B – Датчик уровня моторного масла – диапазон/функционирование цепи
P252F – Слишком высокий уровень моторного масла
P2704 – Фрикционный элемент E КПП, время применения — диапазон/функционирование
Jungheinrich System Error Codes list.pdf
Adobe Acrobat Document
168.2 KB
Jungheinrich Fault Codes.pdf
Adobe Acrobat Document
720.8 KB
Jungheinrich Error Codes List PDF.pdf
Adobe Acrobat Document
191.8 KB
Jungheinrich EJC112 & E1202 Event Messag
Adobe Acrobat Document
582.8 KB
Event Messages
Z This display units shows a four-digit event message for every
event. Trucks that only use one luminous display (e.g. LED) show
the event through a flashing code (see «Display System”).
Each event message is also stored in the master logbook. The
master logbook describes the event in more detail through the sub
index behind the event message (FEXX).
Event numbering display
F E XX S
F Function group; E Event group
XX Event number S Sub index
The first two characters “F, E” refer to the category. The middle
two digits “XX” refer to the event. From these two digits the range:
• 1 to 50 describes standard events (uniform basic events)
which can occur in any function group.
• 51 to 99 describes specific events.
The event is described in further detail through the last characters
“S” (single digit / multi-digit).
This process ensures that a unique number is assigned to each
event. Example:
0 Fault reset or
no fault
1 General fault / additional functions
Example:
Logic error, e.g. both directions selected simultaneously
2 Current
(input interface, device-internal, output interface)
3 Voltage
(input interface, device-internal, output interface)
4 Temperature
5 Hardware
Example: Output transformer short circuit, EEPROM not
responding, …
6 Software
(internal software, application software, data record /
parameters)
Example: EEPROM data error
7 Additional modules
8 CAN monitoring
9 External fault
Example: ISM
Password: https://www.pdfmanual4trucks.com/
Title |
File Size |
Download Links |
Jungheinrich EJC112 / E1202 Event Messages Codes List PDF |
619.4kb |
Download |
Jungheinrich Error Codes List PDF [PDF] |
199kb |
Download |
Jungheinrich Fault Codes [PDF] |
769kb |
Download |
Jungheinrich LISTADO ERRORES [PDF] |
199kb |
Download |
Jungheinrich System Error Codes list [PDF] |
162.7kb |
Download |
Display error code |
Cause |
Action |
1901 |
During system start-up, the accelerator pedal zero position could not |
Do not press the accelerator pedal during system start-up. |
1904 |
Accelerator pedal pressed, but no travel direction selected. |
Take your foot off the accelerator pedal, select a travel direction and set off. |
1909 |
Accelerator pedal pressed and parking brake not released via parking |
Release the parking brake by pressing the parking brake button. |
1917 |
Accelerator and brake pedals pressed simultaneously. |
Press one pedal at a time only. |
2951 |
Lift function activated on multi-/ solo PILOT during system start- up. |
Do not apply the multi-/ solo PILOT during system start- up.
–
–
– |
1952 |
Travel direction switch pressed during system start-up. |
Do not press the travel direction switch during system start-up |
9961 |
ISM (option) has detected a shock event in the vertical |
Obtain acknowledgement from authorized person (warehouse manager) and |
9962 |
ISM (option) has detected a shock event in the horizontal |
Obtain acknowledgement from authorized person (warehouse manager) and |
5990 |
The electrolyte level sensor check (battery-management option) on the |
Add electrolyte. |
5992 |
After switching on the truck, no radio network could be established |
–
–
–
– |
5408/ 5409 |
Lithium-ion battery overtemperature |
Stop work. |
5413 |
Lithium-ion battery low temperature |
Move truck to warm environment. |
For all other warning messages switch the truck off and on again. If the warning message appears again call the service department.
The code lock enables an operator or a group of operators to be assigned an individual user code. The user code is configured with a master code and is outlined in the following sections of this
chapter.
When you have entered the valid user code the truck will be operational. The truck will be able to perform travel, steering and hydraulic operations.
When you have entered the valid master code the truck will be switched on. Travel operations are inhibited. The truck will be able to perform steering and hydraulic operations. The code lock is
in programming mode. When you enter one of the following parameters the settings in the code lock can be changed.
Parameters |
Description |
0-0-0 |
– To change the master code |
0-0-1 |
– To add user codes |
0-0-2 |
– To change a user code |
0-0-3 |
– To clear a user code |
0-0-4 |
– To clear all user codes |
0-1-0 |
– To set the automatic cutout of the truck |
Newly supplied trucks have the code indicated on a sticker. When using the truck for the first time change the master and user codes and remove the sticker.
- User code factory setting: 2-5-8-0
- Master code factory setting: 7-2-9-5
Jungheinrich Service Manual
Jungheinrich DFG/TFG
660-690 Operating Instructions
Models: DFG 670; DFG
680; DFG 690; DFG S80; DFG S90; TFG 660; TFG 670; TFG 680; TFG 690; TFG S80; TFG S90; DFG S90.
Jungheinrich DFG S80
Service Manual
Models: TFG 680; DFG 670; DFG 660; DFG 680; DFG 690; DFG S80; DFG S90; TFG 660; TFG 670; TFG 690; TFG S80; TFG S90.
Jungheinrich DFG TFG
316-435 Operating Instructions
Models: TFG 430; DFG 320; DFG 425; DFG 430; DFG 435; TFG 316; TFG 320; TFG 425; TFG 435.
Jungheinrich EFG-Vac 22-30/ 25L/S/SL Service Manual Download
Jungheinrich ECE 225 (90309857) Spare Parts Catalogue Download
Jungheinrich EJC 110/112 Operating instructions Download
Jungheinrich DFG/TFG 16 — 50 A/B/C-K Operating instructions Download
Jungheinrich DFG 660 Service Manual Download
Jungheinrich DFG 670 Service Manual Download
Jungheinrich DFG S80 Service Manual Download
Jungheinrich DFG_TFG 316-435 Operating Instructions Download
Jungheinrich ECE 225 Spare Parts Catalogue Download
Jungheinrich EFG 213-320 Operating Manual Download
Jungheinrich EFG-Vac 22 Service Manual Download
Jungheinrich EFG-Vac 25L Service Manual Download
Jungheinrich EFG-Vac 30 Service Manual Download
Jungheinrich EJD 220 Service Manual Download
Jungheinrich ERE 120 Service Manual Download
Jungheinrich ETM 214 Service Manual Download
Jungheinrich ETM 216 Service Manual Download
Jungheinrich ETM 325 Service Manual Download
Jungheinrich ETV 214 Service Manual Download
Jungheinrich ETV 216 Service Manual Download
Jungheinrich ETV 318Service Manual Download
Jungheinrich ETV 320 Service Manual Download
Jungheinrich ETV 325 Service Manual Download
Jungheinrich EZS 330 XL Operating Instructions Manual Download
Jungheinrich EZS 350 XL Operating Instructions Manual Download
Jungheinrich SLH 200 Service Manual Download
Jungheinrich TFG 660 Service Manual Download
Jungheinrich Fault Codes
Jungheinrich Fault Codes Download
Jungheinrich EJC112 & E1202 Event Messages Codes List Download
Jungheinrich Error Codes List Download
Jungheinrich Fault Codes Download
Jungheinrich LISTADO ERRORES Download
Jungheinrich System Error Codes list Download
Jungheinrich System Error Codes list Download
Jungheinrich System Error Codes list Download
Jungheinrich forklifts
The manufacturer of forklifts is Jungheinrich, which is a leader in the production and sale of industrial, warehouse and material handling equipment. The company began its journey from 1953, when
a small loader company was founded, and by 2011 the company had several factories at its disposal.
Purpose
Forklifts are mainly used to work in warehouses, but without them they are very rarely managed in large-scale industries. They carry loads that are placed on pallets. Due to the version with a
closed cabin, they are able to work even in places with unfavorable external environment, namely, with wind, dust, sparks, sawdust, steam, and so on.
Electric
Electric loaders are represented by 5 series, which differ in load capacity, low unloading height, technology, maneuverability, as well as convenience of the operator’s workplace.
1 series EFG 110/113/115. The letters mean that this is an electric forklift, the first number indicates the series, and the second two are the maximum carrying
capacity in hundreds of kilograms. These are lightweight and compact loaders that have just one rear wheel. Thanks to these parameters, they have excellent maneuverability and can move even
inside the truck body. However, these «kids» are able to work with a weight of from 1 to 1.5 tons and lift the load to a height of 6.5 meters. AC control electronics may be updated.
EFG 213/215 / 216k / 216 / 218k / 218/220. The index k near some models indicates that the model has a smaller battery, a shorter base and a shorter fork body. This series has
the same dimensions and related benefits. However, the maximum load capacity is increased, as well as equipped with a large number of technologies. In the loader, an electric power steering was
added, the ability to independently configure 5 work programs, replace batteries, a more thoughtful security system, an automatic parking brake, smart electronics, and a maintenance-free brake
system and electric motor. The case in these loaders is integral, which provides greater stability when maneuvering.
EFG 316 / 316k / 318 / 318k / 320. The main differences between these trucks from previous models is that they have 4 wheels and a fully enclosed cab with front and rear window
cleaner. The control system is now electro-hydraulic, which provides better handling. Cab stances were enhanced, and the lighting system and battery compartment received additional protection.
EFG 540k / 540 / 545k / 545/550 / S40 / S30. These are the most powerful and big electric lift trucks. The maximum unloading height has also been increased, but only to 7.18
meters. You can use various packages of additional functions that determine the operation of the loader. In this series, more attention is paid to operator safety, as well as comfort and
ergonomics of the workplace.
Loading…
õUNGHEINRICH |
System Messages |
08.06 |
1 |
G |
|||||||
Error |
Description |
Component |
Display text |
Cause / Action |
Effect |
||||||
1 |
Low voltage during |
F, H, L, |
Low voltage |
Check battery voltage, chargebattery; |
Travel is inhibited. |
||||||
system start |
F-AC, H-AC |
Checkwireconnectiontocontroller; |
|||||||||
ELECTRICAL SYSTEM |
check main current fuse; check main |
Reduced power for |
|||||||||
contactor; replace control part; |
travel and lifting. |
||||||||||
Replacecomponent; |
Warning symbol |
||||||||||
(Limit VN = 80V: VBatt < 64V or |
flashing (Else-Check). |
||||||||||
VCap. < 56V |
|||||||||||
Limit VN = 48V: VBatt < 34V or |
|||||||||||
VCap. < 34V |
|||||||||||
Limit VN = 24V: VBatt <17V) |
|||||||||||
2 |
Overvoltage |
F, H, L, |
Overvoltage |
Check battery voltage; replace |
No travel or hydraulic functions |
||||||
F-AC, H-AC |
BATTERY |
controllerpart; replace component; |
Warning symbol |
||||||||
CONTROLLER |
(Limit VN = 80V: VBatt > 92 V |
flashing (Else-Check). |
|||||||||
Limit VN = 48V: VBatt > 62 V |
|||||||||||
Limit VN = 24V: VBatt > 28 V) |
|||||||||||
3 |
Temperature limit for |
F, H, L, |
TEMPERATURE |
Check sensor and wire connections |
Reduced power for |
||||||
controllers |
F-AC, H-AC |
CONTROLLER |
Allow controllers to cool down; check |
travel and lifting. |
|||||||
> 80°C (>70°C MP1510C) |
fan operation, improve cooling. |
Warning symbol |
|||||||||
or |
Warm up the controller and operate at |
flashing (Else-Check). |
|||||||||
ACS only: |
reduced level until the controller has |
||||||||||
Info at > 85°C |
warmed up. |
||||||||||
Err at > 115°C |
|||||||||||
Err at < -20°C |
|||||||||||
4 |
Emergency Disconnect |
F |
POWER SUPPLY |
Warning |
Brake applies, travel inhibited |
||||||
applied during travel |
(V < 20V MP1510C) |
õUNGHEINRICH |
System Messages |
08.06 |
2 |
G |
|||||||
Error |
Description |
Component |
Display text |
Cause / Action |
Effect |
||||||
5 |
Overvoltage |
F, F-AC, H-AC |
ELECTRICAL SYSTEM |
Check wire connection to battery, |
Brake applies, travel inhibited |
||||||
checkBattery, replacecontroller part; |
|||||||||||
Replace component; |
|||||||||||
(Limit for Retrak: VBatt > 62 V |
|||||||||||
Limit for MP1510C: V > 32 V) |
|||||||||||
6 |
Wire breakage: |
C, I2, I3, I4, I5, |
TRAVEL SWITCH |
Check wire connection; |
Travel stop. “Warning” symbol flashes |
||||||
— Travel setpoint device |
Travel switch |
Replace travel setpoint device; |
(Else-Check). Hydraulic functions |
||||||||
Replace Canion/ Interface; |
possible |
||||||||||
7 |
Key switch applied |
F,F-AC,H-AC |
KEY SWITCH |
Warning |
Brake applies, travel inhibited |
||||||
duringtravel |
(V < 13V for 200ms MP1510C) |
||||||||||
8 |
2 travel directions applied |
F-AC, H-AC, C, |
ELECTRICAL SYSTEM |
Warning, replace travel direction |
Travel stop. “Warning” symbol |
||||||
simultaneously |
MP, S, I2, I3, I5, |
switch, replace Interface 7 Canion; |
flashing (Else-Check). |
||||||||
FS |
replace Multipilot / Solopilot |
Hydraulic functions possible |
|||||||||
For twin pedal, check the electrical |
|||||||||||
system. |
|||||||||||
9 |
Operator protection switch |
I2, FS |
ELECTRICAL SYSTEM |
Check switch, check wire connections |
|||||||
faulty |
|||||||||||
10 |
V Cap. <> V Batt; (main |
F, H, |
MAIN CONTACTOR |
Check main contactor, check wire |
No travel, hydraulics |
||||||
contactor jammed or not |
F-AC, H-AC |
connection; check output pin 2 (ACS) of |
Warning symbol |
||||||||
open) |
L |
traction controller; replace component |
Flashing warning (Else-Check). |
||||||||
11 |
Offset error armature / |
F, H, L, |
CONTROLLER |
Check main current wire, replace |
Travel no function |
||||||
field current (DC) |
F-AC, H-AC |
component |
|||||||||
Stator current (AC); |
|||||||||||
Current measurement |
|||||||||||
point |
|||||||||||
12 |
Disable driver field |
F, H |
CONTROLLER |
Replace component; |
No travel, hydraulics |
||||||
rheostat faulty for DC |
F-AC, H-AC |
for AC: Check flat belt wire connection; |
Warning symbol |
||||||||
Disable driver power |
L |
replace power part |
Flashing warning (Else-Check). |
||||||||
stage faulty (forAC) |
|||||||||||
õUNGHEINRICH |
System Messages |
08.06 |
3 |
G |
|||||||
Error |
Description |
Component |
Display text |
Cause / Action |
Effect |
||||||
13 |
Disable Watchdog field |
F, H |
CONTROLLER |
Replace components |
Travel no function |
||||||
faulty |
|||||||||||
14 |
— Main contactor notclosed |
F, H, |
CONTROLLER/ |
Check wire connection; check main |
No travel, hydraulics |
||||||
— Field power stage cannot |
F-AC, H-AC |
MAIN CONTACTOR |
contactor; check charging connection, |
Warning symbol |
|||||||
be switched on (DC) |
Check field supply fuse, |
Flashing warning (Else-Check). |
|||||||||
Replace component. |
|||||||||||
15 |
Disable field faulty; |
F, H, |
CONTROLLER |
Replace controlpart; replace |
Travel no function |
||||||
Illegal address (for AC) |
F-AC, H-AC |
component |
|||||||||
L |
|||||||||||
16 |
Disable driver armature |
F, H, |
CONTROLLER |
Replace controlpart (AC); replace |
Travel no function |
||||||
actuator faulty; |
F-AC, H-AC |
component |
|||||||||
Software reset (for AC) |
|||||||||||
17 |
Disable Watchdog |
F, H |
CONTROLLER |
Replace components |
Travel no function |
||||||
armature faulty |
|||||||||||
18 |
DC: Armature power |
F, H, F-AC, H-AC |
CONTROLLER |
Check armature wire connection; |
Travel no function |
||||||
stage cannot be switched |
L |
replace power part; replace component |
|||||||||
on |
|||||||||||
AC: one of the 3 phases |
|||||||||||
cannot be switched on |
õUNGHEINRICH |
System Messages |
08.06 |
4 |
G |
||||||
Error |
Description |
Component |
Display text |
Cause / Action |
Effect |
|||||
19 |
Disable armature faulty; |
F, H, F-AC ,H- |
CONTROLLER |
Replace power part; Replace |
Travel no function |
|||||
Power stage short circuit |
AC, |
component. |
||||||||
(for AC) |
L-AC |
Can occur in connection with error 70, |
||||||||
The error may be |
in this case: |
|||||||||
triggered by the faulty |
check power supply behind the main |
|||||||||
speed sensor in |
contactor contact, in the event of an |
|||||||||
connection with |
error the voltage will be much lower |
|||||||||
AS4814Plus controllers. |
here than the rated operating voltage. |
|||||||||
Sensor wheel wobbles |
Disconnect the positive supply from the |
|||||||||
(elliptical) or the sensor- |
components to target the error cause. |
|||||||||
sensor wheel gap is too |
The exception here is the F1 traction |
|||||||||
big. In this case the |
controller which must remain |
|||||||||
component is not faulty. |
connected. One component overloads |
|||||||||
A short circuit cannot be |
the testing voltage due to internal short |
|||||||||
resolved by switching the |
circuit. |
|||||||||
truck off/on. |
The testing voltage arises by charging |
|||||||||
the internal capacitor batteries via a |
||||||||||
resistor to the level of the control |
||||||||||
voltage supply. |
||||||||||
Check sensor, replace sensor and / or |
||||||||||
sensor wheel. |
||||||||||
20 |
Armature incorrectly |
F, H |
ELECTRICAL SYSTEM |
Check armature main current wire |
Travel no function |
|||||
connected |
connection |
|||||||||
21 |
Armature overvoltage |
F, H, F-AC, H-AC |
CONTROLLER/ |
Check main current wire to armature; |
||||||
(short circuit / high side |
L |
ELECTR |
check settings(for AC); |
|||||||
faulty) |
AArmature > 360A for 250ms (MP1510); |
|||||||||
Replace component. |
||||||||||
õUNGHEINRICH |
System Messages |
08.06 |
5 |
G |
|||||||
Error |
Description |
Component |
Display text |
Cause / Action |
Effect |
||||||
22 |
Watchdog error; |
F, H, L, M, S, A, |
CONTROLLER/ |
Truck reset, |
No travel, hydraulics |
||||||
Watchdog does not run |
I2, I3, I4, C, |
CANION |
Replace controlpart; replace |
Warning symbol |
|||||||
out |
F-AC, H-AC, FS |
component |
Flashing warning (Else-Check). |
||||||||
23 |
— Computer overload |
F, H, L, M, S, A, |
CONTROLLER / CAN |
Check CAN bus connection; |
No travel, hydraulics |
||||||
— Permanent interrupt |
I2, I3, I4, C, |
Check CANION connector and |
Warning symbol |
||||||||
— “ACS” timeout on |
F-AC, H-AC, FS |
component; |
Flashing warning (Else-Check). |
||||||||
CAN connection |
Replace component |
||||||||||
24 |
EEPROM cannot be |
F, H, L, I2, I3, I4, |
CONTROLLER/ |
Check battery cable; check VBatt; set |
Flashing warning symbol (Else- |
||||||
contacted / parameters |
C, |
CANION |
trucktype, set default parameters; |
Check). |
|||||||
not plausible / parameter |
F-AC, H-AC |
replace control part; replace |
|||||||||
set to default |
MFC brake |
component |
|||||||||
Faulty checksum |
MFC hydr. , travel |
Delete logbook, change parameters, |
|||||||||
switch |
set hourmeter, replace component |
||||||||||
25 |
No telegrams: |
F, H, I4, I8 |
INTERFACE / CAN |
Check CANBus connection, check wire |
|||||||
— no logon from |
F-AC, H-AC |
connection between proportional valve |
|||||||||
interface |
L |
– modulation; check fuse 1F8; replace |
|||||||||
iInterface (I2, I4, I8) ; replace lift |
|||||||||||
potentiometer, Multipilot, Solopilot or |
|||||||||||
interface; |
|||||||||||
MP1510C: Voltage collapses, controller |
|||||||||||
logs on again, interface does not, |
|||||||||||
controller remains blocked and waits for |
|||||||||||
interface. |
|||||||||||
Check battery voltage (with load!); |
|||||||||||
charge or replace battery if necessary; |
|||||||||||
— no telegrams from |
AS2409K: no “live” telegram received |
||||||||||
from CAN Bus travel switch for more |
|||||||||||
Can-Bus travel switch |
than 300 ms; replace travel switch |
õUNGHEINRICH |
System Messages |
08.06 |
6 |
G |
|||||||
Error |
Description |
Component |
Display text |
Cause / Action |
Effect |
||||||
26 |
Wire breakage: |
M, S, I2, I3 |
MULTIPILOT / |
Check wire connection |
Lift stop. “Warning” symbol flashes |
||||||
— Lift potentiometer |
SOLOPILOT / LIFT |
(Else-Check), travel enabled |
|||||||||
POTENTIOMETER |
|||||||||||
27 |
Wire breakage: |
C, L, I3, I4 |
STEER ACTUAL |
Check wire connection; |
Crawl speed, |
||||||
— Steering setpoint device; |
ANGLE |
Replace steer angle sensor / |
Flashing warning symbol (Else- |
||||||||
◊ Reach truck: for 45° |
potentiometer; |
Check), hydraulic functions enabled. |
|||||||||
steering bolster movement |
Replace Canion / Interface; |
This error produces an emergency |
|||||||||
no flank from proximity |
Replace steering; |
stop on the reach truck and the |
|||||||||
switch. |
PM2402L from software version 1.60: |
Juniors. |
|||||||||
◊ Canion: “Steer angle |
|||||||||||
acquire active” parameter |
set parameter P511 “operating mode” |
||||||||||
has incorrect value |
correctly ◊ 1 = analog sensor |
||||||||||
◊ Juniors PM2402L: |
(potentiometer), |
||||||||||
“Operating mode” |
2 = digital sensor on steer motor |
||||||||||
parameter incorrectly set |
|||||||||||
28 |
Wire breakage: |
C, L, I3, I4 |
STEER NOMINAL |
Check wire connection, replace |
Crawl speed, |
||||||
— Steering sensor |
ANGLE |
steering wheel sensor;replace Canion / |
Flashing warning symbol (Else- |
||||||||
interface; replace steering |
Check), hydraulic functions enabled. |
||||||||||
This error produces an emergency |
|||||||||||
stop on the reach |
truck |
||||||||||
29 |
Wire breakage: |
M |
Traverse nominal value |
Replace Multipilot |
|||||||
— Traverse potentiometer |
MULTIPILOT |
||||||||||
30 |
Wire breakage: |
M |
Tilt nominal value |
Replace Multipilot, |
|||||||
— Tilt potentiometer |
MULTIPILOT |
Teach Multipilot (Hall sensor 2003 only) |
|||||||||
31 |
Wire breakage: |
M, S |
Sideshift nominal value |
Replace Multipilot / Solopilot, |
Hydraulic functions stop, “Warning” |
||||||
— ZH1 setpoint device |
MULTIPILOT / |
Teach Multipilot (Hall sensor 2003 |
symbol flashes (Else-Check), travel |
||||||||
SOLOPILOT |
only); |
enabled |
|||||||||
— Initial lift / lower |
Travel switch |
Travel switch: Check / replace switch |
|||||||||
Setpoint device |
|||||||||||
õUNGHEINRICH |
System Messages |
08.06 |
7 |
G |
|||||||
Error |
Description |
Component |
Display text |
Cause / Action |
Effect |
||||||
32 |
Wire breakage: |
M, S |
MULTIPILOT / |
Replace Multipilot / Solopilot, |
Hydraulic functions stop, “Warning” |
||||||
— ZH2 setpoint device |
SOLOPILOT |
Teach Multipilot (Hall sensor 2003 only) |
symbol flashes (Else-Check), travel |
||||||||
enabled |
|||||||||||
33 |
Wire breakage: |
M, I8 |
MULTIPILOT |
Replace Multipilot |
|||||||
— ZH3 setpoint device |
|||||||||||
34 |
CANBus damaged |
F, H, L, M, S, A, |
CAN-BUS |
Check CAN bus connection; |
No travel, hydraulics |
||||||
I2, I3, I4, I5, C, F- |
replace faulty component; |
Warning symbol |
|||||||||
AC, H-AC |
Check terminal resistances |
Flashing warning (Else-Check). Only |
|||||||||
Travel switch |
stored in logbook (from 2004). |
||||||||||
35 |
No travel zero position |
I2, I3, I4, C |
TRAVEL ZERO |
Warning, check travel switch; |
Travel stop, |
||||||
Deadman and accelerator |
Travel switch |
POSITION |
Intermittent contact in interface power |
Flashing warning symbol (Else- |
|||||||
pedal applied when truck |
supply (12 volts) |
Check), hydraulic functions enabled. |
|||||||||
switched on |
Check Canion, for twin pedal check |
||||||||||
electrical system |
|||||||||||
36 |
No lift zero position |
M, I2, I3,FS |
LIFT ZERO POSITION |
Warning, check lift setpoint device. |
Hydraulic functions stop, “Warning” |
||||||
symbol flashes (Else-Check), travel |
|||||||||||
enabled |
|||||||||||
37 |
No steering angle nominal |
L |
CONTROLLER / CAN |
Check steering setpoint device;Check |
|||||||
value |
CANBus connection; check “steer type” |
||||||||||
parameter; Replace component (I5) |
|||||||||||
38 |
Component does not log |
F, H, L, I2, I3, I4, |
CONTROLLER / CAN |
Check CAN-Bus connection and |
No travel, lifting |
||||||
on, self test not |
C, A, M, S, F-AC, |
voltage; check DIL switch 7 encoding |
Warning symbol |
||||||||
concluded. |
H-AC |
(MP1510); steering controller |
Flashing warning (Else-Check). |
||||||||
monitoring activated? (AS2412F); |
|||||||||||
check ACS encoding; replace |
|||||||||||
component |
õUNGHEINRICH |
System Messages |
08.06 |
8 |
G |
||||||
Error |
Description |
Component |
Display text |
Cause / Action |
Effect |
|||||
39 |
Implausible truck type |
F, H, L, I2, I3, I4, |
TRUCK TYPE |
For 1. Set truck type; |
||||||
1. Discovered during the |
I5, A, M, |
For 2. Examine and if necessary |
||||||||
self test phase that at |
F-AC, H-AC |
replace switch (key switch) or rectify |
||||||||
least one component |
intermittent contact in power supply |
|||||||||
has a different truck |
plug connections. |
|||||||||
type as a parameter. |
Set truck type. |
|||||||||
A different truck type was |
||||||||||
discovered in operating |
||||||||||
mode. Caused by |
||||||||||
intermittent contacts in the |
||||||||||
power supply connections |
||||||||||
40 |
Motor overtemperature |
L, F, H |
TEMPERATURE |
Warning; check motor sensor system |
Reduced power for |
|||||
Traction motor |
F-AC, H-AC |
MOTOR |
and wire connections; |
travel and lifting. |
||||||
overtemperature in |
Check motor; traction motor brake |
Warning symbol |
||||||||
operating mode.> 150°C |
open? |
flashing (Else-Check). For steering |
||||||||
And travel speed < 1km/h |
only |
|||||||||
For ACS: |
warning symbol flashing. |
|||||||||
Info > 145°C |
||||||||||
Err > 165°C |
||||||||||
41 |
Brake magnet |
L |
BRAKE |
Check potentiometer; check |
||||||
potentiometer |
MAGNETPOTENTIOM |
potentiometer attachment; check wire |
||||||||
Potentiometer voltage less |
ETER |
connection |
||||||||
than 0.3 volts or greater |
||||||||||
than 2.7 volts for more |
||||||||||
than 500ms. |
õUNGHEINRICH |
System Messages |
08.06 |
9 |
G |
|||||
Error |
Description |
Component |
Display text |
Cause / Action |
Effect |
||||
42 |
— Short circuit between |
L,F |
BRAKE MAGNET |
Check wire connection, check brake |
|||||
the output and battery |
magnet; replace component |
||||||||
positive.(EJC, ELE) |
|||||||||
-Brake magnet control, |
|||||||||
below minimum difference |
|||||||||
on potentiometer for 500 |
|||||||||
ms when magnet applied. |
|||||||||
(150mV ) |
|||||||||
No brake pressure during |
|||||||||
initialization. |
|||||||||
Brake pressure after the |
|||||||||
Emergency Stop magnet |
|||||||||
has applied; |
|||||||||
43 |
Adjust brake |
L |
ADJUST BRAKE |
Adjust brake; check potentiometer |
|||||
44 |
—Brake not connected or |
L,F |
BRAKE FAULTY |
-Check brake wiring, replace brake if |
No release |
||||
connection wire short |
necessary |
||||||||
circuit |
-Replace brake cable, check |
||||||||
potentiometer; Check potentiometer |
|||||||||
-Brake cable torn |
attachment; |
||||||||
Only for steer category_3: |
Only for steer category_3: |
||||||||
Internal driver of failsafe |
|||||||||
brake cannot connect the |
-Check brake driver output, check |
||||||||
relay |
switch contact plausibility, |
||||||||
Or short circuit bypass |
Replace steer component. |
||||||||
(contact jams) on the |
|||||||||
output during power up |
|||||||||
test |
German-made Jungheinrich loading equipment is distinguished by excellent durability and
performance. Benefit from consistently high handling speeds with maximum comfort. This European-quality equipment perfectly adapts to various operating conditions, meets strict safety standards,
is distinguished by high working and driving qualities for moving and storing goods for work both in an open area and inside a closed warehouse or a freight railway container.
Jungheinrich LPG trucks, like trucks from other brands of this type, have a number of advantages. This is a universal warehouse
equipment, which is very economical if, when buying it, you correctly calculate the basic requirements for the height of lifting of loads, carrying capacity, speed of movement, weight of the
machine, its dimensions and, of course, the types of cargo with which the machine has to deal. If the calculation is carried out carefully, and the optimal model is chosen, the costs for it,
given the low price of gas, will pay off in a few months. And due to its high ecological class, it can work on a shift all day long with practically different cargoes that require specific
transportation conditions. The peculiarity of gas forklifts is that you can start them in any weather without any problems, which can not be said about diesel or gasoline ones.
Jungheinrich electric forklift EFG 115
The EFG 115 is the most compact electric forklift from the German concern Jungheinrich. It can be used in the smallest rooms,
including wagons and wagons. It has the following technical characteristics:
The distribution of weight to the front axle is 3805/1270.
Carrying capacity — 1500 kg.
Total weight 2870 kg.
Engine:
running — 4 kW;
lifting — 6 kW.
The maximum speed is 12.5 km / h.
Clearance — 100 mm.
The wheelbase is 1200 mm.
The center of gravity of the load on the forks is 500 mm.
Mast tilt (a / b) in degrees — 5/6.
Mast — 2000-3550 mm.
Working corridor width:
across — 3114 mm;
along — 3236 mm.
The total width is 990 mm.
The total length is 2935 mm.
The service brake is hydraulic.
The maximum lifting height is 3000 mm.
The maximum climb is 16 degrees.
Fork dimensions (LxWxH) — 1150x100x35 mm.
Lifting speed with / without load — 240/500 mm / s.
Lowering speed with / without load — 580/600 mm / s.
It is worth noting that it is quite difficult to find a new Jungheinrich EFG 115 loader in the domestic market. However, these
forklifts are quite widely used, and here the price depends on the condition of the machine. In general, the cost can vary from 3,000 to 10,000 euros. The new EFG 115 will cost about 18,500
euros.
Electric forklift Jungheinrich EFG 215
The second series of EFG loaders differs from the first in a large set of technical options. All this could not but affect the cost, which will be
slightly higher than the 115 model. However, first, let’s look at the technical specifications:
The distribution of weight to the front axle is 3870/1310.
Carrying capacity — 1500 kg.
Total weight 2978 kg.
Engine:
running — 4.6 kW;
lifting — 11.5 kW.
Storage battery (voltage V / capacity kW * h) — 48/500.
The maximum speed is 16 km / h.
Clearance — 100 mm.
The wheelbase is 1249 mm.
The center of gravity of the load on the forks is 500 mm.
Mast tilt (a / b) in degrees — 7/7.
Mast — 2000-3560 mm.
Working corridor width:
across — 3104 mm;
Along — 3226 mm.
The total width is 1060 mm.
The total length is 2924 mm.
The service brake is electromechanical.
The maximum lifting height is 3000 mm.
The maximum climb is 35 degrees.
Turning radius — 1440 mm.
Fork dimensions (LxWxH) — 1150x100x35 mm.
Lifting speed with / without load — 460/600 mm / s.
Lowering speed with / without load — 550/550 mm / s.
As you can see from the technical characteristics, this car has almost the same dimensions as the previous model, but with more powerful motors and
improved other indicators.
Jungheinrich System Error Codes list.pdf
Adobe Acrobat Document
168.2 KB
Jungheinrich Fault Codes.pdf
Adobe Acrobat Document
720.8 KB
Jungheinrich Error Codes List PDF.pdf
Adobe Acrobat Document
191.8 KB
Jungheinrich EJC112 & E1202 Event Messag
Adobe Acrobat Document
582.8 KB
Event Messages
Z This display units shows a four-digit event message for every
event. Trucks that only use one luminous display (e.g. LED) show
the event through a flashing code (see «Display System”).
Each event message is also stored in the master logbook. The
master logbook describes the event in more detail through the sub
index behind the event message (FEXX).
Event numbering display
F E XX S
F Function group; E Event group
XX Event number S Sub index
The first two characters “F, E” refer to the category. The middle
two digits “XX” refer to the event. From these two digits the range:
• 1 to 50 describes standard events (uniform basic events)
which can occur in any function group.
• 51 to 99 describes specific events.
The event is described in further detail through the last characters
“S” (single digit / multi-digit).
This process ensures that a unique number is assigned to each
event. Example:
0 Fault reset or
no fault
1 General fault / additional functions
Example:
Logic error, e.g. both directions selected simultaneously
2 Current
(input interface, device-internal, output interface)
3 Voltage
(input interface, device-internal, output interface)
4 Temperature
5 Hardware
Example: Output transformer short circuit, EEPROM not
responding, …
6 Software
(internal software, application software, data record /
parameters)
Example: EEPROM data error
7 Additional modules
8 CAN monitoring
9 External fault
Example: ISM
Jungheinrich Service Manual
Jungheinrich DFG/TFG
660-690 Operating Instructions
Models: DFG 670; DFG
680; DFG 690; DFG S80; DFG S90; TFG 660; TFG 670; TFG 680; TFG 690; TFG S80; TFG S90; DFG S90.
Jungheinrich DFG S80
Service Manual
Models: TFG 680; DFG 670; DFG 660; DFG 680; DFG 690; DFG S80; DFG S90; TFG 660; TFG 670; TFG 690; TFG S80; TFG S90.
Jungheinrich DFG TFG
316-435 Operating Instructions
Models: TFG 430; DFG 320; DFG 425; DFG 430; DFG 435; TFG 316; TFG 320; TFG 425; TFG 435.
Jungheinrich EFG-Vac 22-30/ 25L/S/SL Service Manual Download
Jungheinrich ECE 225 (90309857) Spare Parts Catalogue Download
Jungheinrich EJC 110/112 Operating instructions Download
Jungheinrich DFG/TFG 16 — 50 A/B/C-K Operating instructions Download
Jungheinrich DFG 660 Service Manual Download
Jungheinrich DFG 670 Service Manual Download
Jungheinrich DFG S80 Service Manual Download
Jungheinrich DFG_TFG 316-435 Operating Instructions Download
Jungheinrich ECE 225 Spare Parts Catalogue Download
Jungheinrich EFG 213-320 Operating Manual Download
Jungheinrich EFG-Vac 22 Service Manual Download
Jungheinrich EFG-Vac 25L Service Manual Download
Jungheinrich EFG-Vac 30 Service Manual Download
Jungheinrich EJD 220 Service Manual Download
Jungheinrich ERE 120 Service Manual Download
Jungheinrich ETM 214 Service Manual Download
Jungheinrich ETM 216 Service Manual Download
Jungheinrich ETM 325 Service Manual Download
Jungheinrich ETV 214 Service Manual Download
Jungheinrich ETV 216 Service Manual Download
Jungheinrich ETV 318Service Manual Download
Jungheinrich ETV 320 Service Manual Download
Jungheinrich ETV 325 Service Manual Download
Jungheinrich EZS 330 XL Operating Instructions Manual Download
Jungheinrich EZS 350 XL Operating Instructions Manual Download
Jungheinrich SLH 200 Service Manual Download
Jungheinrich TFG 660 Service Manual Download
Jungheinrich Fault Codes
Jungheinrich Fault Codes Download
Jungheinrich EJC112 & E1202 Event Messages Codes List Download
Jungheinrich Error Codes List Download
Jungheinrich Fault Codes Download
Jungheinrich LISTADO ERRORES Download
Jungheinrich System Error Codes list Download
Jungheinrich System Error Codes list Download
Jungheinrich System Error Codes list Download
Jungheinrich forklifts
The manufacturer of forklifts is Jungheinrich, which is a leader in the production and sale of industrial, warehouse and material handling equipment. The company began its journey from 1953, when
a small loader company was founded, and by 2011 the company had several factories at its disposal.
Purpose
Forklifts are mainly used to work in warehouses, but without them they are very rarely managed in large-scale industries. They carry loads that are placed on pallets. Due to the version with a
closed cabin, they are able to work even in places with unfavorable external environment, namely, with wind, dust, sparks, sawdust, steam, and so on.
Electric
Electric loaders are represented by 5 series, which differ in load capacity, low unloading height, technology, maneuverability, as well as convenience of the operator’s workplace.
1 series EFG 110/113/115. The letters mean that this is an electric forklift, the first number indicates the series, and the second two are the maximum carrying
capacity in hundreds of kilograms. These are lightweight and compact loaders that have just one rear wheel. Thanks to these parameters, they have excellent maneuverability and can move even
inside the truck body. However, these «kids» are able to work with a weight of from 1 to 1.5 tons and lift the load to a height of 6.5 meters. AC control electronics may be updated.
EFG 213/215 / 216k / 216 / 218k / 218/220. The index k near some models indicates that the model has a smaller battery, a shorter base and a shorter fork body. This series has
the same dimensions and related benefits. However, the maximum load capacity is increased, as well as equipped with a large number of technologies. In the loader, an electric power steering was
added, the ability to independently configure 5 work programs, replace batteries, a more thoughtful security system, an automatic parking brake, smart electronics, and a maintenance-free brake
system and electric motor. The case in these loaders is integral, which provides greater stability when maneuvering.
EFG 316 / 316k / 318 / 318k / 320. The main differences between these trucks from previous models is that they have 4 wheels and a fully enclosed cab with front and rear window
cleaner. The control system is now electro-hydraulic, which provides better handling. Cab stances were enhanced, and the lighting system and battery compartment received additional protection.
EFG 540k / 540 / 545k / 545/550 / S40 / S30. These are the most powerful and big electric lift trucks. The maximum unloading height has also been increased, but only to 7.18
meters. You can use various packages of additional functions that determine the operation of the loader. In this series, more attention is paid to operator safety, as well as comfort and
ergonomics of the workplace.
Password: https://www.pdfmanual4trucks.com/
Title |
File Size |
Download Links |
Jungheinrich EJC112 / E1202 Event Messages Codes List PDF |
619.4kb |
Download |
Jungheinrich Error Codes List PDF [PDF] |
199kb |
Download |
Jungheinrich Fault Codes [PDF] |
769kb |
Download |
Jungheinrich LISTADO ERRORES [PDF] |
199kb |
Download |
Jungheinrich System Error Codes list [PDF] |
162.7kb |
Download |
Display error code |
Cause |
Action |
1901 |
During system start-up, the accelerator pedal zero position could not |
Do not press the accelerator pedal during system start-up. |
1904 |
Accelerator pedal pressed, but no travel direction selected. |
Take your foot off the accelerator pedal, select a travel direction and set off. |
1909 |
Accelerator pedal pressed and parking brake not released via parking |
Release the parking brake by pressing the parking brake button. |
1917 |
Accelerator and brake pedals pressed simultaneously. |
Press one pedal at a time only. |
2951 |
Lift function activated on multi-/ solo PILOT during system start- up. |
Do not apply the multi-/ solo PILOT during system start- up.
–
–
– |
1952 |
Travel direction switch pressed during system start-up. |
Do not press the travel direction switch during system start-up |
9961 |
ISM (option) has detected a shock event in the vertical |
Obtain acknowledgement from authorized person (warehouse manager) and |
9962 |
ISM (option) has detected a shock event in the horizontal |
Obtain acknowledgement from authorized person (warehouse manager) and |
5990 |
The electrolyte level sensor check (battery-management option) on the |
Add electrolyte. |
5992 |
After switching on the truck, no radio network could be established |
–
–
–
– |
5408/ 5409 |
Lithium-ion battery overtemperature |
Stop work. |
5413 |
Lithium-ion battery low temperature |
Move truck to warm environment. |
For all other warning messages switch the truck off and on again. If the warning message appears again call the service department.
The code lock enables an operator or a group of operators to be assigned an individual user code. The user code is configured with a master code and is outlined in the following sections of this
chapter.
When you have entered the valid user code the truck will be operational. The truck will be able to perform travel, steering and hydraulic operations.
When you have entered the valid master code the truck will be switched on. Travel operations are inhibited. The truck will be able to perform steering and hydraulic operations. The code lock is
in programming mode. When you enter one of the following parameters the settings in the code lock can be changed.
Parameters |
Description |
0-0-0 |
– To change the master code |
0-0-1 |
– To add user codes |
0-0-2 |
– To change a user code |
0-0-3 |
– To clear a user code |
0-0-4 |
– To clear all user codes |
0-1-0 |
– To set the automatic cutout of the truck |
Newly supplied trucks have the code indicated on a sticker. When using the truck for the first time change the master and user codes and remove the sticker.
- User code factory setting: 2-5-8-0
- Master code factory setting: 7-2-9-5
German-made Jungheinrich loading equipment is distinguished by excellent durability and
performance. Benefit from consistently high handling speeds with maximum comfort. This European-quality equipment perfectly adapts to various operating conditions, meets strict safety standards,
is distinguished by high working and driving qualities for moving and storing goods for work both in an open area and inside a closed warehouse or a freight railway container.
Jungheinrich LPG trucks, like trucks from other brands of this type, have a number of advantages. This is a universal warehouse
equipment, which is very economical if, when buying it, you correctly calculate the basic requirements for the height of lifting of loads, carrying capacity, speed of movement, weight of the
machine, its dimensions and, of course, the types of cargo with which the machine has to deal. If the calculation is carried out carefully, and the optimal model is chosen, the costs for it,
given the low price of gas, will pay off in a few months. And due to its high ecological class, it can work on a shift all day long with practically different cargoes that require specific
transportation conditions. The peculiarity of gas forklifts is that you can start them in any weather without any problems, which can not be said about diesel or gasoline ones.
Jungheinrich electric forklift EFG 115
The EFG 115 is the most compact electric forklift from the German concern Jungheinrich. It can be used in the smallest rooms,
including wagons and wagons. It has the following technical characteristics:
The distribution of weight to the front axle is 3805/1270.
Carrying capacity — 1500 kg.
Total weight 2870 kg.
Engine:
running — 4 kW;
lifting — 6 kW.
The maximum speed is 12.5 km / h.
Clearance — 100 mm.
The wheelbase is 1200 mm.
The center of gravity of the load on the forks is 500 mm.
Mast tilt (a / b) in degrees — 5/6.
Mast — 2000-3550 mm.
Working corridor width:
across — 3114 mm;
along — 3236 mm.
The total width is 990 mm.
The total length is 2935 mm.
The service brake is hydraulic.
The maximum lifting height is 3000 mm.
The maximum climb is 16 degrees.
Fork dimensions (LxWxH) — 1150x100x35 mm.
Lifting speed with / without load — 240/500 mm / s.
Lowering speed with / without load — 580/600 mm / s.
It is worth noting that it is quite difficult to find a new Jungheinrich EFG 115 loader in the domestic market. However, these
forklifts are quite widely used, and here the price depends on the condition of the machine. In general, the cost can vary from 3,000 to 10,000 euros. The new EFG 115 will cost about 18,500
euros.
Electric forklift Jungheinrich EFG 215
The second series of EFG loaders differs from the first in a large set of technical options. All this could not but affect the cost, which will be
slightly higher than the 115 model. However, first, let’s look at the technical specifications:
The distribution of weight to the front axle is 3870/1310.
Carrying capacity — 1500 kg.
Total weight 2978 kg.
Engine:
running — 4.6 kW;
lifting — 11.5 kW.
Storage battery (voltage V / capacity kW * h) — 48/500.
The maximum speed is 16 km / h.
Clearance — 100 mm.
The wheelbase is 1249 mm.
The center of gravity of the load on the forks is 500 mm.
Mast tilt (a / b) in degrees — 7/7.
Mast — 2000-3560 mm.
Working corridor width:
across — 3104 mm;
Along — 3226 mm.
The total width is 1060 mm.
The total length is 2924 mm.
The service brake is electromechanical.
The maximum lifting height is 3000 mm.
The maximum climb is 35 degrees.
Turning radius — 1440 mm.
Fork dimensions (LxWxH) — 1150x100x35 mm.
Lifting speed with / without load — 460/600 mm / s.
Lowering speed with / without load — 550/550 mm / s.
As you can see from the technical characteristics, this car has almost the same dimensions as the previous model, but with more powerful motors and
improved other indicators.
Неполадки складской техники и их диагностика
Прогресс не стоит на месте, добавляя в устройство техники все новые агрегаты, поэтому конструкция специальных машин с каждым годом только усложняется. Однако, чем сложнее техника, тем сложнее ее обслуживание и диагностика.
К счастью, для облегчения работы и быстрого анализа поломок и внештатных ситуаций были придуманы специальные датчики, которые снабжают сервисменов информацией о конкретных точках поломки. Такая система уже давно работает в автомобильной промышленности и зарекомендовала себя с лучшей стороны.
Требование к погрузочной технике не является исключением, так как ее простой может обойтись бизнесу в круглую сумму. Важно, чтобы своевременная и быстрая диагностика, а также устранение неисправностей стали главными задачами.
Чтобы облегчить сервису по обслуживанию складской техники (ричтрак, вилочный погрузчик и электроштабелер) работу, были придуманы специальные коды ошибок и неполадок, которые указывают на точные проблемы, возникшие с техникой. Такая система не только ускоряет работу по ремонту, но и исключает человеческий фактор.
Какие коды существуют
Коды делятся на ошибки и неисправности. Их все можно с легкостью диагностировать и исправить в короткие сроки.
Самые часто встречающиеся неполадки и ошибки, которые можно диагностировать с помощью кодов
- Предупреждение о неправильной операции обучения
- Короткое замыкание верхних и нижних FET
- Короткое замыкание верхней стороны
- Короткое замыкание нижней стороны
- Повреждение провода фазы U
- Повреждение провода фазы V
- Повреждение провода фазы W
- Повышение температуры
- Температура не соответствует норме
- Короткое замыкание цепей нагрузки
- Мотор насоса (Повышение температуры)
- Мотор насоса (Температура не соответствует норме)
- Входной сигнал внешнего контролера выходит за пределы нормативного диапазона
- Неисправность датчика температуры контроллера погрузочно-разгрузочных операций
- Неисправность датчика температуры мотора насоса
Также спецзначки на панели приборов могут сигнализировать о необходимости технического обслуживания, замене технических жидкостей или о смене и подборе новой АКБ. Главное помнить, что, несмотря на кажущуюся простоту складской техники, ни в коем случае нельзя самому пытаться исправить ошибки. Чтобы избежать дорогостоящих расходов, всегда лучше обратиться в квалифицированную сервисную службу. Она своевременно и качественно починит все неполадки, и вам не придется ни о чем беспокоиться. Более того, в случае самостоятельного ремонта вы можете потерять гарантию на свою технику. Так как только после сервисного ремонта процент повторной поломки сведется к минимуму.