Все современные копировальные аппараты, мфу и принтеры Kyocera имеют возможность диагностировать все узлы устройства в режиме запуска и во время работы аппарата. По этому, если во время включения или во время работы произошел сбой, то техника Kyocera сможет сообщить о наличии ошибки.
В большинстве случаев у аппаратов Kyocera код ошибки отображается на дисплее, в остальных случаях тип ошибки зависит от последовательности и количества миганий индикаторов.
Если Ваш копировальный аппарат, МФУ или принтер Kyocera выдал на дисплее некий код, то узнать причину, описание возникновения ошибки, а так же в каком узле аппарата стоит искать проблему, Вы можете в этом разделе выбрав интересующую модель из списка.
Но диагностика не решит проблему сбоя аппарата, для этого лучше обратиться к профессиональным и опытным сервисным специалистам компании Kyomart! Позвоните нам по телефону
8 (343) 288-23-45 или отправьте запрос на электронную почту: sales@kyomart.ru , и мы обязательно свяжемся с Вами в кратчайшие сроки.
| Код ошибки | Описание ошибки | Причина ошибки |
|---|---|---|
| 0030 | FAX control PWB system error Processing with the fax software was disabled due to a hardware problem. |
Defective FAX control PWB. |
| 0060 | Engine PWB type error | Defective engine sub PCB. |
| 0070 | FAX control PWB incompatible detection error Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted. |
Defective FAX software Defective FAX control PWB. |
| 0100 | Backup memory device error | Defective flash memory. |
| 0120 | MAC address data error For data in which the MAC address is invalid. |
Defective main PWB. Defective flash memory. Defective engine PWB. |
| 0130 | Backup memory read/write error (main PWB) | Defective flash memory. Defective main PWB. |
| 0140 | Backup memory data error (main PWB) | Defective flash memory. Defective main PWB. |
| 0150 | Backup memory read/write error (engine PWB) Detecting engine PWB EEPROM communication error. |
Improper installation engine PWB EEPROM. Defective engine PWB. Device damage of EEPROM. |
| 0160 | Backup memory data error (engine PWB) | Defective flash memory. Defective engine PWB. |
| 0170 | Billing counting error A checksum error is detected in the main and engine backup memories for the billing counters. |
Data damage of EEPROM. Defective PWB. |
| 0180 | Machine number mismatch Machine number of main and engine does not match. |
Data damage of EEPROM. |
| 0320 | I/O CPU communication error A communication error is detected 10 times in succession. |
Defective PWB. |
| 0630 | DMA error DMA transmission of image data does not complete within the specified period of time. | Poor contact in the connector terminals. Defective main PWB. |
| 0800 | Image processing error JAM05 is detected twice. |
Defective main PWB. |
| 0830 | FAX control PWB flash program area checksum error A checksum error occurred with the program of the FAX control PWB. |
Defective FAX software. Defective FAX control PWB. |
| 0840 | Faults of RTC The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed. |
The battery is disconnected from the main PWB. Defective main PWB. |
| 0870 | FAX control PWB to main PWB high capacity data transfer error High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times. |
Improper installation FAX control PWB. Defective FAX control PWB or main PWB. |
| 0920 | Fax file system error The backup data is not retained for file system abnormality of flash memory of the FAX control PWB. |
Defective FAX control PWB. |
| 1010 | Lift motor error After cassette 1 is inserted, lift sensor does not turn on within 12 s. This error is detected four times successively. |
Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the lift motor. Defective lift motor. Defective engine PWB. |
| 1020 | PF lift motor error (paper feeder) After cassette 2 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected four times successively. |
Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor 1. Defective PF lift motor 1. Defective PF main PWB. |
| 1030 | PF lift motor error (paper feeder) After cassette 3 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected four times successively. |
Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor 2. Defective PF lift motor 2. Defective PF main PWB. |
| 1800 | Paper feeder communication error A communication error is detected 10 times in succession. |
Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective PF main PWB. |
| 1900 | Paper feeder EEPROM error When writing the data, the write data and the read data is not continuously in agreement 5 times. |
Defective PF main PWB. Device damage of EEPROM. |
| 2000 | Main motor steady-state error Stable OFF is detected for 1 s continuously after main motor stabilized. |
Defective connector cable or poor contact in the connector. Defective drive transmission system of the main motor. Defective main motor. Defective engine PWB. |
| 2010 | Main motor drive error The main motor is not stabilized within 2 s after driving starts. |
Defective connector cable or poor contact in the connector. Defective drive transmission system of the main motor. Defective main motor. Defective engine PWB. |
| 2600 | PF drive motor error (paper feeder) When the PF drive motor is driven, error signal is detected continuously for 1 s. |
Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF drive motor. Defective PF drive motor. Defective PF main PWB. |
| 3100 | ISU home position error The home position is not correct when the power is turned on or at the start of copying using the table. |
Defective connector cable or poor contact in the connector. Defective home position sensor. Defective ISU motor. Defective CCD PWB. Defective engine PWB. |
| 3200 | Exposure lamp error When input value at the time of exposure lamp illumination does not exceed the threshold value between 5 s. |
Defective connector cable or poor contact in the connector. Defective exposure lamp. Defective CCD PWB. Defective main PWB. |
| 3500 | Communication error between scanner and ASIC An error code is detected 3 times in succession. |
Defective connector cable or poor contact in the connector. Defective CCD PWB. Defective main PWB. |
| 3600 | Scanner sequence error | Defective main PWB or engine PWB. |
| 4000 | Polygon motor synchronization error The polygon motor is not stabilized within 10 s after driving starts. |
Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| 4010 | Polygon motor steady-state error Stable OFF is detected for 1 s continuously after polygon motor stabilized. |
Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| 4100 | BD initialization error BD is not detected within 1 s after polygon motor stabilized. |
Defective connector cable or poor contact in the connector. Defective APC PWB. Defective BD PWB. Defective main PWB. |
| 4700 | VIDEO ASIC device error | Defective connector cable or poor contact in the connector. Defective main PWB or engine PWB. |
| 6000 | Broken fuser heater wire The detected temperature of fuser thermistor does not reach the specified temperature (ready indication temperature) after the fuser heater has been turned on continuously for 60 s in warming up. The fusing temperature at 7 seconds and 20 seconds since fuser temperature control has occurred differs by 43°C/109.4°F or less. |
Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Broken fuser heater wire. Defective engine PWB. |
| 6000 6020 6030 6050 |
Broken fuser heater wire Abnormally high fuser thermistor temperature Broken fuser thermistor wire Abnormally low fuser thermistor temperature |
Deformed connector pin. Defective triac. |
| 6020 | Abnormally high fuser thermistor temperature The fuser thermistor detects a temperature higher than 230°C/446°F continuously for 40 ms. High fuser temperature signal detects a temperature of 255°C/491°F continuously for 40 ms. |
Deformed connector pin. Defective triac. Shorted fuser thermistor. Defective engine PWB. |
| 6030 | Broken fuser thermistor wire A/D value of the fuser thermistor exceeds 251 bit continuously for 7 s during warming up. |
Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Defective fuser thermistor. Defective engine PWB |
| 6050 | Abnormally low fuser thermistor temperature As the stable temperature has reached the second time, the decrease in the fuser thermistor temperature of 60°C/140°F or greater is detected for one second. |
Deformed connector pin. Defective triac. Defective fuser thermistor Defective fuser heater. Defective engine PWB. |
| 6400 | Zero-cross signal error While fuser heater control is performed, the zero-cross signal is not input within 3 s. |
Defective connector cable or poor contact in the connector Defective power source PWB or engine PWB. |
| 7800 | Broken external thermistor wire The thermistor output value is 0.3 V or less. |
Defective connector cable or poor contact in the connector. Defective temperature sensor. |
| 7810 | Short-circuited external thermistor wire The thermistor output value is 3 V or more. |
Defective connector cable or poor contact in the connector. Defective temperature sensor. |
| 7900 | Drum unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. |
Defective connector cable or poor contact in the connector. Defective drum unit. |
| 7910 | Developer unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. |
Defective connector cable or poor contact in the connector. Defective developer unit. |
| 8030 | Tray upper limit detection problem (document finisher) When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected. |
Defective connector cable or poor contact in the connector. Defective tray upper limit sensor, paper surface sensor 1/2. Defective DF main PWB. |
| 8040 | Belt problem (document finisher) The belt sensor does not turn on/off within specified time of the belt solenoid turning on. |
Defective connector cable or poor contact in the connector. Defective belt sensor. Defective belt solenoid. Defective DF main PWB. |
| 8140 | Tray elevation motor problem (document finisher) The tray low limit sensor or paper surface sensor 1/2 cannot be detected to be on within 10 s since the tray elevation motor is activated. |
Defective connector cable or poor contact in the connector. Defective connector cable or poor contact in the connector. The tray elevation motor malfunctions. Defective tray lower limit sensor, paper surface sensor 1/2. Defective DF main PWB. |
| 8210 | Stapler problem (document finisher) Jam 7012 or 7023 is indicated. |
Defective connector cable of staple or poor contact in the connector. The stapler is blocked with a staple. The stapler is broken Defective DF main PWB. |
| 8320 | Adjustment motor 2 problem (document finisher) The adjustment sensor 2 does not turn on/off within specified time of the adjustment motor 2 turning on. |
Defective connector cable or poor contact in the connector. Defective adjustment sensor 2. Defective adjustment motor 2. Defective DF main PWB. |
| 8330 | Adjustment motor 1 problem (document finisher) The adjustment sensor 1 does not turn on/off within specified time of the adjustment motor 1 turning on. |
Defective connector cable or poor contact in the connector. Defective adjustment sensor 1. Defective adjustment motor 1. |
| 8350 | Roller motor problem (document finisher) The roller sensor does not turn on/off within specified time of the roller motor turning on. |
Defective DF main PWB. Defective connector cable or poor contact in the connector. Defective roller sensor. Defective roller motor. Defective DF main PWB. |
| 8360 | Slide motor problem (document finisher) The slide sensor does not turn on/off within specified time of the slide motor turning on. |
Defective connector cable or poor contact in the connector. Defective slide sensor. Defective slide motor. Defective DF main PWB. |
| 8460 | EEPROM problem (document finisher) Reading from or writing to EEPROM cannot be performed. |
Defective EEPROM or DF main PWB. |
| 8800 | Document finisher communication error A communication error is detected 10 times in succession. |
Defective connector cable or poor contact in the connector Defective DF main PWB. Defective engine PWB. |
| 8830 | Bridge communication error (document finisher) A communication error is detected 10 times in succession. |
Defective connector cable or poor contact in the connector. Defective bridge PWB. Defective engine PWB. |
| 8990 | Document finisher communication error | Defective connector cable or poor contact in the connector. Defective DF main PWB. Defective bridge PWB. |
| 9000 | Document processor communication error A communication error is detected 10 times in succession. |
Defective connector cable or poor contact in the connector. Defective DP main PWB. |
| 9060 | DP EEPROM error Read and write data does not match. Data in the specified area of the backup memory does not match the specified values. | Defective DP main PWB. Device damage of EEPROM. |
| 9500 | BRU communication error | IPU PWB error |
| 9510 | BRU PWB error | IPU PWB error |
| 9520 | BRU PWB data error | IPU PWB error |
| F000 | Main PWB — operation panel PWB communication error | Defective main PWB. Defective operation panel PWB. |
| F010 | Main PWB checksum error | Defective main PWB. |
| F040 | Main PWB — print engine communication error | Defective main PWB. Defective engine PWB. |
| F050 | Print engine ROM checksum error | Defective engine PWB. |
Code
4204
Laser output error (Yellow)
The pin photo signal (PDN) is not output
from PD PWB Y for one second while
laser is emitted.
4600
LSU cleaning motor error
When the LSU cleaning motor is driven,
the LSU cleaning motor over-current
detection signal is detected continu-
ously for 50 times (5 s) at 100 ms inter-
vals.
4700
VIDEO ASIC device error
Contents
Causes
Check procedures/corrective measures
Defective harness
Reinsert the connector. Also check for conti-
between APC
nuity within the connector harness. If none,
PWB Y and engine
remedy or replace the harness.
PWB (YC29), or
improper connec-
tor insertion.
Defective APC
Replace the laser scanner unit YK (See
PWB Y.
page 1-5-37).
Defective PD PWB
Replace the laser scanner unit YK (See
Y.
page 1-5-37).
Defective engine
Replace the engine PWB (See page 1-5-
PWB.
29).
Defective harness
Reinsert the connector. Also check for conti-
between LSU
nuity within the connector harness. If none,
cleaning motor and
remedy or replace the harness.
engine PWB
(YC37), or
improper connec-
tor insertion.
Defective drive
Check if the rollers and gears rotate
transmission sys-
smoothly. If not, grease the bushings and
tem of the LSU
gears. Check for broken gears and replace if
cleaning motor.
any.
Defective LSU
Replace the LSU cleaning motor.
cleaning motor.
Defective engine
Replace the engine PWB (See page 1-5-
PWB.
29).
Faulty connection
Check the installation of the main PWB and
of the connector
engine PWB and reinstall them if necessary
between the main
(See page 1-5-28 and 1-5-29).
PWB and engine
PWB.
Defective main
Replace the main PWB (See page 1-5-28).
PWB.
Defective engine
Replace the engine PWB (See page 1-5-
PWB.
29).
Remarks
2K8
1-4-11
Ошибка 4600
Ошибка блока лазера. Не работает\заедает двигатель очистки лазера. Как правило из за пыли. Необходимо прочистить направляющие блока лазеров.
Разборка МФУ
- Отключаем МФУ от электросети
- Вынимаем лотки с бумагой
- Открываем крышку блока картриджей
- Выкручиваем винты из крышки слева
- Снимаем крышку
Блок лазеров
- Отсоединяем кабели
- Выкручиваем 4 винта крепления
- Вытаскиваем блок лазеров
Чистка блока лазеров
- Очищаем направляющие от пыли (продуть воздухом)
- Вставляем блок обратно
- Подключаем кабель, проверяем что бы все было плотно
- Подключаем электропитание, включаем МФУ и проверяем что все работает
- Собираем в обратном порядке
Все современные копировальные аппараты, мфу и принтеры Kyocera имеют возможность диагностировать все узлы устройства в режиме запуска и во время работы аппарата. По этому, если во время включения или во время работы произошел сбой, то техника Kyocera сможет сообщить о наличии ошибки.
В большинстве случаев у аппаратов Kyocera код ошибки отображается на дисплее, в остальных случаях тип ошибки зависит от последовательности и количества миганий индикаторов.
Если Ваш копировальный аппарат, МФУ или принтер Kyocera выдал на дисплее некий код, то узнать причину, описание возникновения ошибки, а так же в каком узле аппарата стоит искать проблему, Вы можете в этом разделе выбрав интересующую модель из списка.
Но диагностика не решит проблему сбоя аппарата, для этого лучше обратиться к профессиональным и опытным сервисным специалистам компании Kyomart! Позвоните нам по телефону
8 (343) 288-23-45 или отправьте запрос на электронную почту: sales@kyomart.ru , и мы обязательно свяжемся с Вами в кратчайшие сроки.
| Код ошибки | Описание ошибки | Причина ошибки |
|---|---|---|
| 0030 | FAX control PWB system error Processing with the fax software was disabled due to a hardware problem. |
Defective FAX control PWB. |
| 0060 | Engine PWB type error | Defective engine sub PCB. |
| 0070 | FAX control PWB incompatible detection error Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted. |
Defective FAX software Defective FAX control PWB. |
| 0100 | Backup memory device error | Defective flash memory. |
| 0120 | MAC address data error For data in which the MAC address is invalid. |
Defective main PWB. Defective flash memory. Defective engine PWB. |
| 0130 | Backup memory read/write error (main PWB) | Defective flash memory. Defective main PWB. |
| 0140 | Backup memory data error (main PWB) | Defective flash memory. Defective main PWB. |
| 0150 | Backup memory read/write error (engine PWB) Detecting engine PWB EEPROM communication error. |
Improper installation engine PWB EEPROM. Defective engine PWB. Device damage of EEPROM. |
| 0160 | Backup memory data error (engine PWB) | Defective flash memory. Defective engine PWB. |
| 0170 | Billing counting error A checksum error is detected in the main and engine backup memories for the billing counters. |
Data damage of EEPROM. Defective PWB. |
| 0180 | Machine number mismatch Machine number of main and engine does not match. |
Data damage of EEPROM. |
| 0320 | I/O CPU communication error A communication error is detected 10 times in succession. |
Defective PWB. |
| 0630 | DMA error DMA transmission of image data does not complete within the specified period of time. | Poor contact in the connector terminals. Defective main PWB. |
| 0800 | Image processing error JAM05 is detected twice. |
Defective main PWB. |
| 0830 | FAX control PWB flash program area checksum error A checksum error occurred with the program of the FAX control PWB. |
Defective FAX software. Defective FAX control PWB. |
| 0840 | Faults of RTC The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed. |
The battery is disconnected from the main PWB. Defective main PWB. |
| 0870 | FAX control PWB to main PWB high capacity data transfer error High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times. |
Improper installation FAX control PWB. Defective FAX control PWB or main PWB. |
| 0920 | Fax file system error The backup data is not retained for file system abnormality of flash memory of the FAX control PWB. |
Defective FAX control PWB. |
| 1010 | Lift motor error After cassette 1 is inserted, lift sensor does not turn on within 12 s. This error is detected four times successively. |
Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the lift motor. Defective lift motor. Defective engine PWB. |
| 1020 | PF lift motor error (paper feeder) After cassette 2 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected four times successively. |
Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor 1. Defective PF lift motor 1. Defective PF main PWB. |
| 1030 | PF lift motor error (paper feeder) After cassette 3 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected four times successively. |
Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor 2. Defective PF lift motor 2. Defective PF main PWB. |
| 1800 | Paper feeder communication error A communication error is detected 10 times in succession. |
Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective PF main PWB. |
| 1900 | Paper feeder EEPROM error When writing the data, the write data and the read data is not continuously in agreement 5 times. |
Defective PF main PWB. Device damage of EEPROM. |
| 2000 | Main motor steady-state error Stable OFF is detected for 1 s continuously after main motor stabilized. |
Defective connector cable or poor contact in the connector. Defective drive transmission system of the main motor. Defective main motor. Defective engine PWB. |
| 2010 | Main motor drive error The main motor is not stabilized within 2 s after driving starts. |
Defective connector cable or poor contact in the connector. Defective drive transmission system of the main motor. Defective main motor. Defective engine PWB. |
| 2600 | PF drive motor error (paper feeder) When the PF drive motor is driven, error signal is detected continuously for 1 s. |
Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF drive motor. Defective PF drive motor. Defective PF main PWB. |
| 3100 | ISU home position error The home position is not correct when the power is turned on or at the start of copying using the table. |
Defective connector cable or poor contact in the connector. Defective home position sensor. Defective ISU motor. Defective CCD PWB. Defective engine PWB. |
| 3200 | Exposure lamp error When input value at the time of exposure lamp illumination does not exceed the threshold value between 5 s. |
Defective connector cable or poor contact in the connector. Defective exposure lamp. Defective CCD PWB. Defective main PWB. |
| 3500 | Communication error between scanner and ASIC An error code is detected 3 times in succession. |
Defective connector cable or poor contact in the connector. Defective CCD PWB. Defective main PWB. |
| 3600 | Scanner sequence error | Defective main PWB or engine PWB. |
| 4000 | Polygon motor synchronization error The polygon motor is not stabilized within 10 s after driving starts. |
Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| 4010 | Polygon motor steady-state error Stable OFF is detected for 1 s continuously after polygon motor stabilized. |
Defective connector cable or poor contact in the connector. Defective polygon motor. Defective engine PWB. |
| 4100 | BD initialization error BD is not detected within 1 s after polygon motor stabilized. |
Defective connector cable or poor contact in the connector. Defective APC PWB. Defective BD PWB. Defective main PWB. |
| 4700 | VIDEO ASIC device error | Defective connector cable or poor contact in the connector. Defective main PWB or engine PWB. |
| 6000 | Broken fuser heater wire The detected temperature of fuser thermistor does not reach the specified temperature (ready indication temperature) after the fuser heater has been turned on continuously for 60 s in warming up. The fusing temperature at 7 seconds and 20 seconds since fuser temperature control has occurred differs by 43°C/109.4°F or less. |
Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Broken fuser heater wire. Defective engine PWB. |
| 6000 6020 6030 6050 |
Broken fuser heater wire Abnormally high fuser thermistor temperature Broken fuser thermistor wire Abnormally low fuser thermistor temperature |
Deformed connector pin. Defective triac. |
| 6020 | Abnormally high fuser thermistor temperature The fuser thermistor detects a temperature higher than 230°C/446°F continuously for 40 ms. High fuser temperature signal detects a temperature of 255°C/491°F continuously for 40 ms. |
Deformed connector pin. Defective triac. Shorted fuser thermistor. Defective engine PWB. |
| 6030 | Broken fuser thermistor wire A/D value of the fuser thermistor exceeds 251 bit continuously for 7 s during warming up. |
Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Defective fuser thermistor. Defective engine PWB |
| 6050 | Abnormally low fuser thermistor temperature As the stable temperature has reached the second time, the decrease in the fuser thermistor temperature of 60°C/140°F or greater is detected for one second. |
Deformed connector pin. Defective triac. Defective fuser thermistor Defective fuser heater. Defective engine PWB. |
| 6400 | Zero-cross signal error While fuser heater control is performed, the zero-cross signal is not input within 3 s. |
Defective connector cable or poor contact in the connector Defective power source PWB or engine PWB. |
| 7800 | Broken external thermistor wire The thermistor output value is 0.3 V or less. |
Defective connector cable or poor contact in the connector. Defective temperature sensor. |
| 7810 | Short-circuited external thermistor wire The thermistor output value is 3 V or more. |
Defective connector cable or poor contact in the connector. Defective temperature sensor. |
| 7900 | Drum unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. |
Defective connector cable or poor contact in the connector. Defective drum unit. |
| 7910 | Developer unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. |
Defective connector cable or poor contact in the connector. Defective developer unit. |
| 8030 | Tray upper limit detection problem (document finisher) When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected. |
Defective connector cable or poor contact in the connector. Defective tray upper limit sensor, paper surface sensor 1/2. Defective DF main PWB. |
| 8040 | Belt problem (document finisher) The belt sensor does not turn on/off within specified time of the belt solenoid turning on. |
Defective connector cable or poor contact in the connector. Defective belt sensor. Defective belt solenoid. Defective DF main PWB. |
| 8140 | Tray elevation motor problem (document finisher) The tray low limit sensor or paper surface sensor 1/2 cannot be detected to be on within 10 s since the tray elevation motor is activated. |
Defective connector cable or poor contact in the connector. Defective connector cable or poor contact in the connector. The tray elevation motor malfunctions. Defective tray lower limit sensor, paper surface sensor 1/2. Defective DF main PWB. |
| 8210 | Stapler problem (document finisher) Jam 7012 or 7023 is indicated. |
Defective connector cable of staple or poor contact in the connector. The stapler is blocked with a staple. The stapler is broken Defective DF main PWB. |
| 8320 | Adjustment motor 2 problem (document finisher) The adjustment sensor 2 does not turn on/off within specified time of the adjustment motor 2 turning on. |
Defective connector cable or poor contact in the connector. Defective adjustment sensor 2. Defective adjustment motor 2. Defective DF main PWB. |
| 8330 | Adjustment motor 1 problem (document finisher) The adjustment sensor 1 does not turn on/off within specified time of the adjustment motor 1 turning on. |
Defective connector cable or poor contact in the connector. Defective adjustment sensor 1. Defective adjustment motor 1. |
| 8350 | Roller motor problem (document finisher) The roller sensor does not turn on/off within specified time of the roller motor turning on. |
Defective DF main PWB. Defective connector cable or poor contact in the connector. Defective roller sensor. Defective roller motor. Defective DF main PWB. |
| 8360 | Slide motor problem (document finisher) The slide sensor does not turn on/off within specified time of the slide motor turning on. |
Defective connector cable or poor contact in the connector. Defective slide sensor. Defective slide motor. Defective DF main PWB. |
| 8460 | EEPROM problem (document finisher) Reading from or writing to EEPROM cannot be performed. |
Defective EEPROM or DF main PWB. |
| 8800 | Document finisher communication error A communication error is detected 10 times in succession. |
Defective connector cable or poor contact in the connector Defective DF main PWB. Defective engine PWB. |
| 8830 | Bridge communication error (document finisher) A communication error is detected 10 times in succession. |
Defective connector cable or poor contact in the connector. Defective bridge PWB. Defective engine PWB. |
| 8990 | Document finisher communication error | Defective connector cable or poor contact in the connector. Defective DF main PWB. Defective bridge PWB. |
| 9000 | Document processor communication error A communication error is detected 10 times in succession. |
Defective connector cable or poor contact in the connector. Defective DP main PWB. |
| 9060 | DP EEPROM error Read and write data does not match. Data in the specified area of the backup memory does not match the specified values. | Defective DP main PWB. Device damage of EEPROM. |
| 9500 | BRU communication error | IPU PWB error |
| 9510 | BRU PWB error | IPU PWB error |
| 9520 | BRU PWB data error | IPU PWB error |
| F000 | Main PWB — operation panel PWB communication error | Defective main PWB. Defective operation panel PWB. |
| F010 | Main PWB checksum error | Defective main PWB. |
| F040 | Main PWB — print engine communication error | Defective main PWB. Defective engine PWB. |
| F050 | Print engine ROM checksum error | Defective engine PWB. |
Code
4204
Laser output error (Yellow)
The pin photo signal (PDN) is not output
from PD PWB Y for one second while
laser is emitted.
4600
LSU cleaning motor error
When the LSU cleaning motor is driven,
the LSU cleaning motor over-current
detection signal is detected continu-
ously for 50 times (5 s) at 100 ms inter-
vals.
4700
VIDEO ASIC device error
Contents
Causes
Check procedures/corrective measures
Defective harness
Reinsert the connector. Also check for conti-
between APC
nuity within the connector harness. If none,
PWB Y and engine
remedy or replace the harness.
PWB (YC29), or
improper connec-
tor insertion.
Defective APC
Replace the laser scanner unit YK (See
PWB Y.
page 1-5-37).
Defective PD PWB
Replace the laser scanner unit YK (See
Y.
page 1-5-37).
Defective engine
Replace the engine PWB (See page 1-5-
PWB.
29).
Defective harness
Reinsert the connector. Also check for conti-
between LSU
nuity within the connector harness. If none,
cleaning motor and
remedy or replace the harness.
engine PWB
(YC37), or
improper connec-
tor insertion.
Defective drive
Check if the rollers and gears rotate
transmission sys-
smoothly. If not, grease the bushings and
tem of the LSU
gears. Check for broken gears and replace if
cleaning motor.
any.
Defective LSU
Replace the LSU cleaning motor.
cleaning motor.
Defective engine
Replace the engine PWB (See page 1-5-
PWB.
29).
Faulty connection
Check the installation of the main PWB and
of the connector
engine PWB and reinstall them if necessary
between the main
(See page 1-5-28 and 1-5-29).
PWB and engine
PWB.
Defective main
Replace the main PWB (See page 1-5-28).
PWB.
Defective engine
Replace the engine PWB (See page 1-5-
PWB.
29).
Remarks
2K8
1-4-11
-
Catalog
-
Sign In
-
Contacts
-
Forum
-
Eng
- Error Codes
- Kyocera
- FSC8520MFP
- Code 4600
- Code: 4600
- Description: LSU cleaning motor error
When the LSU cleaning motor is driven, an error signal is detected continuously for 1 s. - Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system. Defective motor. Defective PWB.
- Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity of the connector cable. If none, replace the cable. LSU cleaning motor and LSU connect PWB(YC11) LSU connect PWB and engine PWB(YC12)
Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
Defective motor. Replace the LSU cleaning motor.
Defective PWB. Replace the engine PWB or LSU connect PWB check for correct operation.
Thanks: 0
Likes: 0
Dislikes: 0
-
11-04-2014
#1
Trusted Tech
50+ Posts
- Rep Power
- 26
Kyocera FS-C2126 C4600 Error code
Hi Guys
Got a FS-C2126 with a c4600 error code, I took the Laser units out and checked the operation of the Laser cleaner by hand. I’m thinking it might be in the motor and gear assy. but wanted to check and see if anybody’s had this problem before I start tearing the machine down for that its in a customers office and not much room to move around.
-
11-05-2014
#2
Re: Kyocera FS-C2126 C4600 Error code
There’s a bulletin on this. Essentially, the manufacturer totally redesigned the slit glass cleaner drive. The new parts do not fit on the old style laser. So you have two choices:
1) Replace two laser assemblies with new style parts.
2) Once every 3 months you’ll need to remove the transfer belt, drums, developing units, loosen two screws securing the rear laser, and manually home out the laser slit glass cleaner.Personally, I selected the second choice. =^..^=
If you’d like a serious answer to your request:
1) demonstrate that you’ve read the manual
2) demonstrate that you made some attempt to fix it.
3) if you’re going to ask about jams include the jam code.
4) if you’re going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=
-
11-05-2014
#3
Trusted Tech
50+ Posts
- Rep Power
- 26
Re: Kyocera FS-C2126 C4600 Error code
Thank You Blackcat, I’ll check the Bulletins again and probably do the same thing to home it out whenever it kicks up the code.
-
11-20-2014
#4
Trusted Tech
50+ Posts
- Rep Power
- 26
Re: Kyocera FS-C2126 C4600 Error code
Blackcat could you email me the bulletin for this problem I haven’t been able to find it, Thank you in advance
-
06-15-2015
#5
Technician
- Rep Power
- 25
Re: Kyocera FS-C2126 C4600 Error code
I have the same problem and I can’t find the Bulletin either. Do you have the bulletin number or can you send me a copy of the bulletin? dougmoney@gmail.com
Thanks.
-
06-23-2015
#6
Technician
- Rep Power
- 23
Re: Kyocera FS-C2126 C4600 Error code
Same problem, just power off the machine, disconnect the wire of laser cleaning motor from engine, power on the machine and it works, while powered on reconnect the motor and still working fine. It sounds like easy to solve by firmware mod.
Bookmarks
Bookmarks
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
- BB code is On
- Smilies are On
- [IMG] code is On
- [VIDEO] code is On
- HTML code is Off
Forum Rules
Все современные копировальные аппараты, мфу и принтеры Kyocera имеют возможность диагностировать все узлы устройства в режиме запуска и во время работы аппарата. По этому, если во время включения или во время работы произошел сбой, то техника Kyocera сможет сообщить о наличии ошибки.
В большинстве случаев у аппаратов Kyocera код ошибки отображается на дисплее, в остальных случаях тип ошибки зависит от последовательности и количества миганий индикаторов.
Если Ваш копировальный аппарат, МФУ или принтер Kyocera выдал на дисплее некий код, то узнать причину, описание возникновения ошибки, а так же в каком узле аппарата стоит искать проблему, Вы можете в этом разделе выбрав интересующую модель из списка.
Но диагностика не решит проблему сбоя аппарата, для этого лучше обратиться к профессиональным и опытным сервисным специалистам компании Kyomart! Позвоните нам по телефону
8 (343) 288-23-45 или отправьте запрос на электронную почту: sales@kyomart.ru , и мы обязательно свяжемся с Вами в кратчайшие сроки.
Код ошибки
Описание ошибки
Причина ошибки
0030
FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem.
Defective FAX control PWB.
0060
Engine PWB type error
Defective engine sub PCB.
0070
FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted.
Defective FAX software
Defective FAX control PWB.
0100
Backup memory device error
Defective flash memory.
0120
MAC address data error
For data in which the MAC address is invalid.
Defective main PWB.
Defective flash memory.
Defective engine PWB.
0130
Backup memory read/write error (main PWB)
Defective flash memory.
Defective main PWB.
0140
Backup memory data error (main PWB)
Defective flash memory.
Defective main PWB.
0150
Backup memory read/write error (engine PWB)
Detecting engine PWB EEPROM communication error.
Improper installation engine PWB EEPROM.
Defective engine PWB.
Device damage of EEPROM.
0160
Backup memory data error (engine PWB)
Defective flash memory.
Defective engine PWB.
0170
Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters.
Data damage of EEPROM.
Defective PWB.
0180
Machine number mismatch
Machine number of main and engine does not match.
Data damage of EEPROM.
0320
I/O CPU communication error
A communication error is detected 10 times in succession.
Defective PWB.
0630
DMA error DMA transmission of image data does not complete within the specified period of time.
Poor contact in the connector terminals. Defective main PWB.
0800
Image processing error
JAM05 is detected twice.
Defective main PWB.
0830
FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB.
Defective FAX software.
Defective FAX control PWB.
0840
Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed.
The battery is disconnected from the main PWB.
Defective main PWB.
0870
FAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times.
Improper installation FAX control PWB.
Defective FAX control PWB or main PWB.
0920
Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB.
Defective FAX control PWB.
1010
Lift motor error
After cassette 1 is inserted, lift sensor does not turn on within 12 s. This error is detected four times successively.
Defective bottom plate elevation mechanism in the cassette.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of the lift motor.
Defective lift motor.
Defective engine PWB.
1020
PF lift motor error (paper feeder)
After cassette 2 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected four times successively.
Defective bottom plate elevation mechanism in the cassette.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of the PF lift motor 1.
Defective PF lift motor 1.
Defective PF main PWB.
1030
PF lift motor error (paper feeder)
After cassette 3 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected four times successively.
Defective bottom plate elevation mechanism in the cassette.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of the PF lift motor 2.
Defective PF lift motor 2.
Defective PF main PWB.
1800
Paper feeder communication error
A communication error is detected 10 times in succession.
Improper installation paper feeder.
Defective connector cable or poor contact in the connector.
Defective engine PWB.
Defective PF main PWB.
1900
Paper feeder EEPROM error
When writing the data, the write data and the read data is not continuously in agreement 5 times.
Defective PF main PWB.
Device damage of EEPROM.
2000
Main motor steady-state error
Stable OFF is detected for 1 s continuously after main motor stabilized.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of the main motor.
Defective main motor.
Defective engine PWB.
2010
Main motor drive error
The main motor is not stabilized within 2 s after driving starts.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of the main motor.
Defective main motor.
Defective engine PWB.
2101
Developer motor K steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the developer motor K stabilizes.
Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB.
2102
Developer motor YCM steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the developer motor YCM stabilizes.
Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB.
2111
Developer motor K startup error
Developer motor K is not stabilized within 2 s since the motor is activated.
Defective connector cable or poor contact in the connector
Defective drive transmission system.
Defective motor.
Defective PWB.
2112
Developer motor YCM startup error
Developer motor YCM is not stabilized within 2 s since the motor is activated.
Defective connector cable or poor contact in the connector
Defective drive transmission system.
Defective motor.
Defective PWB.
2300
Fuser motor steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the fuser motor stabilizes.
Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB.
2310
Fuser motor startup error
Fuser motor is not stabilized within 2 s since the motor is activated.
Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB.
2550
Conveying motor steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the conveying motor stabilizes.
Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB.
2560
Conveying motor startup error
Conveying motor is not stabilized within 2 s since the motor is activated.
Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB.
2600
PF drive motor error (paper feeder)
When the PF drive motor is driven, error signal is detected continuously for 1 s.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of the PF drive motor.
Defective PF drive motor.
Defective PF main PWB.
2700
TC belt motor error
When the TC belt motor is driven, error signal is detected continuously for 1 s.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of the PF drive motor.
Defective PF drive motor.
Defective PF main PWB.
3100
ISU home position error
The home position is not correct when the power is turned on or at the start of copying using the table.
Defective connector cable or poor contact in the connector.
Defective home position sensor.
Defective ISU motor.
Defective CCD PWB.
Defective engine PWB.
3200
Exposure lamp error
When input value at the time of exposure lamp illumination does not exceed the threshold value between 5 s.
Defective connector cable or poor contact in the connector.
Defective exposure lamp.
Defective CCD PWB.
Defective main PWB.
3500
Communication error between scanner and ASIC
An error code is detected 3 times in succession.
Defective connector cable or poor contact in the connector.
Defective CCD PWB.
Defective main PWB.
3600
Scanner sequence error
Defective main PWB or engine PWB.
4000
Polygon motor synchronization error
The polygon motor is not stabilized within 10 s after driving starts.
Defective connector cable or poor contact in the connector.
Defective polygon motor.
Defective engine PWB.
4001
Polygon motor (K) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (K) stabilizes.
Defective connector cable or poor contact in the connector.
Defective motor
Defective PWB.
4002
Polygon motor (С) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (С) stabilizes.
Defective connector cable or poor contact in the connector.
Defective motor
Defective PWB.
4003
Polygon motor (M) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (M) stabilizes.
Defective connector cable or poor contact in the connector.
Defective motor
Defective PWB.
4004
Polygon motor (Y) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (Y) stabilizes.
Defective connector cable or poor contact in the connector.
Defective motor
Defective PWB.
4010
Polygon motor steady-state error
Stable OFF is detected for 1 s continuously after polygon motor stabilized.
Defective connector cable or poor contact in the connector.
Defective polygon motor.
Defective engine PWB.
4011
Polygon motor (K) startup error
Polygon motor (K) is not stabilized within 10 s since the motor is activated.
Defective connector cable or poor contact in the connector.
Defective motor.
Defective PWB.
4012
Polygon motor (C) startup error
Polygon motor (C) is not stabilized within 10 s since the motor is activated.
Defective connector cable or poor contact in the connector.
Defective motor.
Defective PWB.
4013
Polygon motor (M) startup error
Polygon motor (M) is not stabilized within 10 s since the motor is activated.
Defective connector cable or poor contact in the connector.
Defective motor.
Defective PWB.
4014
Polygon motor (Y) startup error
Polygon motor (Y) is not stabilized within 10 s since the motor is activated.
Defective connector cable or poor contact in the connector.
Defective motor.
Defective PWB.
4100
BD initialization error
BD is not detected within 1 s after polygon motor stabilized.
Defective connector cable or poor contact in the connector.
Defective APC PWB.
Defective BD PWB.
Defective main PWB.
4600
LSU cleaning motor error
When the LSU cleaning motor is driven, an error signal is detected continuously for 1 s.
Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor. Defective PWB.
4700
VIDEO ASIC device error
Defective connector cable or poor contact in the connector.
Defective main PWB or engine PWB.
4950
LSU CPU communication error
A communication error is detected 10 times in succession.
Defective connector cable or poor contact in the connector.
Defective PWB.
6000
Broken fuser heater wire
The detected temperature of fuser thermistor does not reach the specified temperature (ready indication temperature) after the fuser heater has been turned on continuously for 60 s in warming up. The fusing temperature at 7 seconds and 20 seconds since fuser temperature control has occurred differs by 43°C/109.4°F or less.
Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB.
6000
6020
6030
6050
Broken fuser heater wire
Abnormally high fuser thermistor temperature Broken fuser thermistor wire Abnormally low fuser thermistor temperature
Deformed connector pin.
Defective triac.
6020
Abnormally high fuser thermistor temperature
The fuser thermistor detects a temperature higher than 230°C/446°F continuously for 40 ms. High fuser temperature signal detects a temperature of 255°C/491°F continuously for 40 ms.
Deformed connector pin.
Defective triac.
Shorted fuser thermistor.
Defective engine PWB.
6030
Broken fuser thermistor wire
A/D value of the fuser thermistor exceeds 251 bit continuously for 7 s during warming up.
Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Defective fuser thermistor.
Defective engine PWB
6050
Abnormally low fuser thermistor temperature
As the stable temperature has reached the second time, the decrease in the fuser thermistor temperature of 60°C/140°F or greater is detected for one second.
Deformed connector pin.
Defective triac.
Defective fuser thermistor
Defective fuser heater.
Defective engine PWB.
6120
Abnormally high fuser thermistor 3 (press roller) temperature
The fuser temperature exceeds 200 °C/392 °F for 1 s.
Deformed connector pin.
Defective IH PWB.
Defective fuser thermistor.
Defective engine PWB.
6130
Fuser thermistor 3 (press roller) break error Fuser thermistor 3 detects a temperature of -14 °C/6.8 °F . Fuser thermistor 3 does not reach 30° C/86 °F even after20 s during warming up.
Defective connector cable or poor contact in the connector
Deformed connector pin.
Defective IH PWB.
Defective fuser thermistor.
Defective engine PWB.
6150
Abnormally low fuser thermistor 3 (press roller) temperature
The fuser temperature lower than 30 °C/86 °F is detected continuously for 1 s.
Deformed connector pin.
Defective fuser thermistor
Defective fuser heater.
Defective engine PWB.
6200
Broken fuser edge heater wire
Fuser thermistor 1 does not reach 50° C/122 °F even after20 s during warming up. The detected temperature of fuser thermistor1 does not reach the specified temperature (ready indication temperature) for 20 s in warming up after reaching 50° C/122 °F.
Defective connector cable or poor contact in the connector.
Deformed connector pin.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB.
6220
Abnormally high fuser thermistor 1 (edge) temperature
The fuser temperature exceeds 240 °C/464 °F for 1 s
Defective connector cable or poor contact in the connector.
Deformed connector pin.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB.
6230
Fuser thermistor 1 (edge) break error
During warming up a hearter, fuser thermistor 2 detects a temperature of 100 °C/212 °F or higher and, fuser thermistor 1 detects a temperature of 37 °C/99 °F or lower.
Defective connector cable or poor contact in the connector.
Deformed connector pin.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB.
6250
Abnormally low fuser thermistor 1 (edge) temperature
The fuser temperature lower than 100 °C/212 °F is detected continuously for 1 s during printing. The fuser temperature lower than 50 °C/122 °F is detected continuously for 1 s during pre-heating.
Defective connector cable or poor contact in the connector.
Deformed connector pin.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB.
6400
Zero-cross signal error
While fuser heater control is performed, the zero-cross signal is not input within 3 s.
Defective connector cable or poor contact in the connector
Defective power source PWB or engine PWB.
6410
Fuser unit type mismatch problem
Absence of the fuser unit is detected.
Fuser unit connector inserted incorrectly.
Different type of the fuser unit is installed.
6600
Belt rotation error
The belt was detected to stop for 1 s continuously during motor remote is on.
Defective fuser motor.
Defective IH belt.
Defective IH PWB.
Defective engine PWB.
7101
Toner sensor K error
Defective Developer unit.
Defective PWB.
7102
Toner sensor C error
Defective Developer unit.
Defective PWB.
7103
Toner sensor M error
Defective Developer unit.
Defective PWB.
7104
Toner sensor Y error
Defective Developer unit.
Defective PWB.
7401
Developing unit K type mismatch problem
Absence of the developing unit K is detected.
Developing unit connector inserted incorrectly.
Different type of the developing unit is installed.
Defective PWB.
7402
Developing unit C type mismatch problem
Absence of the developing unit C is detected.
Developing unit connector inserted incorrectly.
Different type of the developing unit is installed.
Defective PWB.
7403
Developing unit M type mismatch problem
Absence of the developing unit M is detected.
Developing unit connector inserted incorrectly.
Different type of the developing unit is installed.
Defective PWB.
7404
Developing unit Y type mismatch problem
Absence of the developing unit Y is detected.
Developing unit connector inserted incorrectly.
Different type of the developing unit is installed.
Defective PWB.
7411
Drum unit K type mismatch problem
Absence of the drum unit K is detected.
Drum unit connector inserted incorrectly.
Different type of the drum unit is installed.
Defective PWB.
7412
Drum unit C type mismatch problem
Absence of the drum unit C is detected.
Drum unit connector inserted incorrectly.
Different type of the drum unit is installed.
Defective PWB.
7413
Drum unit M type mismatch problem
Absence of the drum unit M is detected.
Drum unit connector inserted incorrectly.
Different type of the drum unit is installed.
Defective PWB.
7414
Drum unit Y type mismatch problem
Absence of the drum unit Y is detected.
Drum unit connector inserted incorrectly.
Different type of the drum unit is installed.
Defective PWB.
7420
Transfer belt unit type mismatch problem
Absence of the transfer belt unit is detected.
Transfer belt unit connector inserted incorrectly.
Different type of the transfer belt unit is installed.
Defective PWB.
7601
ID sensor 1 (front) error
Defective ID sensor.
Defective PWB.
7602
ID sensor 2 (rear) error
Defective ID sensor.
Defective PWB.
7611
ID sensor (K) density error
When ID sensor 2 detected CTD is 500 or less.
Defective ID sensor.
Defective PWB.
7612
ID sensor (C) density error
When ID sensor 2 detected CTD is 500 or less.
Defective ID sensor.
Defective PWB.
7613
ID sensor (M) density error
When ID sensor 2 detected CTD is 500 or less.
Defective ID sensor.
Defective PWB.
7614
ID sensor (Y) density error
When ID sensor 2 detected CTD is 500 or less.
Defective ID sensor.
Defective PWB.
7620
ID sensor timing error
Color registration correction was failed.
Defective ID sensor.
Defective PWB.
7800
Broken external thermistor wire
The thermistor output value is 0.3 V or less.
Defective connector cable or poor contact in the connector.
Defective temperature sensor.
7810
Short-circuited external thermistor wire
The thermistor output value is 3 V or more.
Defective connector cable or poor contact in the connector.
Defective temperature sensor.
7900
Drum unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
Defective connector cable or poor contact in the connector.
Defective drum unit.
7901
Drum K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
Defective connector cable or poor contact in the connector.
Defective drum unit.
7902
Drum C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
Defective connector cable or poor contact in the connector.
Defective drum unit.
7903
Drum M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
Defective connector cable or poor contact in the connector.
Defective drum unit.
7904
Drum Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
Defective connector cable or poor contact in the connector.
Defective drum unit.
7910
Developer unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
Defective connector cable or poor contact in the connector.
Defective developer unit.
7911
Developing unit K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
Poor contact in the connector terminals.
Defective developing PWB.
7912
Developing unit C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
Poor contact in the connector terminals.
Defective developing PWB.
7913
Developing unit M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
Poor contact in the connector terminals.
Defective developing PWB.
7914
Developing unit Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
Poor contact in the connector terminals.
Defective developing PWB.
8030
Tray upper limit detection problem (document finisher)
When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected.
Defective connector cable or poor contact in the connector.
Defective tray upper limit sensor, paper surface sensor 1/2.
Defective DF main PWB.
8040
Belt problem (document finisher)
The belt sensor does not turn on/off within specified time of the belt solenoid turning on.
Defective connector cable or poor contact in the connector.
Defective belt sensor.
Defective belt solenoid.
Defective DF main PWB.
8140
Tray elevation motor problem (document finisher)
The tray low limit sensor or paper surface sensor 1/2 cannot be detected to be on within 10 s since the tray elevation motor is activated.
Defective connector cable or poor contact in the connector.
Defective connector cable or poor contact in the connector.
The tray elevation motor malfunctions.
Defective tray lower limit sensor, paper surface sensor 1/2.
Defective DF main PWB.
8210
Stapler problem (document finisher)
Jam 7012 or 7023 is indicated.
Defective connector cable of staple or poor contact in the connector.
The stapler is blocked with a staple.
The stapler is broken
Defective DF main PWB.
8320
Adjustment motor 2 problem (document finisher)
The adjustment sensor 2 does not turn on/off within specified time of the adjustment motor 2 turning on.
Defective connector cable or poor contact in the connector.
Defective adjustment sensor 2.
Defective adjustment motor 2.
Defective DF main PWB.
8330
Adjustment motor 1 problem (document finisher)
The adjustment sensor 1 does not turn on/off within specified time of the adjustment motor 1 turning on.
Defective connector cable or poor contact in the connector.
Defective adjustment sensor 1.
Defective adjustment motor 1.
8350
Roller motor problem (document finisher)
The roller sensor does not turn on/off within specified time of the roller motor turning on.
Defective DF main PWB.
Defective connector cable or poor contact in the connector.
Defective roller sensor.
Defective roller motor.
Defective DF main PWB.
8360
Slide motor problem (document finisher)
The slide sensor does not turn on/off within specified time of the slide motor turning on.
Defective connector cable or poor contact in the connector.
Defective slide sensor.
Defective slide motor.
Defective DF main PWB.
8460
EEPROM problem (document finisher)
Reading from or writing to EEPROM cannot be performed.
Defective EEPROM or DF main PWB.
8800
Document finisher communication error
A communication error is detected 10 times in succession.
Defective connector cable or poor contact in the connector
Defective DF main PWB.
Defective engine PWB.
8830
Bridge communication error (document finisher)
A communication error is detected 10 times in succession.
Defective connector cable or poor contact in the connector.
Defective bridge PWB.
Defective engine PWB.
8990
Document finisher communication error
Defective connector cable or poor contact in the connector.
Defective DF main PWB.
Defective bridge PWB.
9000
Document processor communication error
A communication error is detected 10 times in succession.
Defective connector cable or poor contact in the connector.
Defective DP main PWB.
9060
DP EEPROM error Read and write data does not match. Data in the specified area of the backup memory does not match the specified values.
Defective DP main PWB.
Device damage of EEPROM.
9500
BRU communication error
IPU PWB error
9510
BRU PWB error
IPU PWB error
9520
BRU PWB data error
IPU PWB error
F000
Main PWB — operation panel PWB communication error
Defective main PWB.
Defective operation panel PWB.
F010
Main PWB checksum error
Defective main PWB.
F040
Main PWB — print engine communication error
Defective main PWB.
Defective engine PWB.
F050
Print engine ROM checksum error
Defective engine PWB.
-
Catalog
-
Sign In
-
Contacts
-
Forum
-
Eng
- Error Codes
- Kyocera
- FSC8520MFP
- Code 4600
- Code: 4600
- Description: LSU cleaning motor error
When the LSU cleaning motor is driven, an error signal is detected continuously for 1 s. - Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system. Defective motor. Defective PWB.
- Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity of the connector cable. If none, replace the cable. LSU cleaning motor and LSU connect PWB(YC11) LSU connect PWB and engine PWB(YC12)
Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
Defective motor. Replace the LSU cleaning motor.
Defective PWB. Replace the engine PWB or LSU connect PWB check for correct operation.
-
08-15-2016
#1
Junior Member
- Rep Power
- 0
Kyocera P6035cdn error C4600
Hi Guys,
I’ve been stuck with a Kyocera ECOsys P6035cdn that is driving me crazy!!!, it keeps giving me a C4600 error which is the LSU cleaning motor error.To date:
-> I’ve upgraded to the latest available firmware,
-> Followed the LSU cleaning motor service bulletins and greased the relevant gears and shafts,
-> Replaced the Engine Relay as prescribed in the service manual.
STILL NO JOY!!!
Anybody have any other options for me to try or ideas other than matches and petrol?
Thanks.
-
08-16-2016
#2
Technician
- Rep Power
- 14
Re: Kyocera P6035cdn error C4600
there is bulletin for the same code
-
08-16-2016
#3
Junior Member
- Rep Power
- 0
Re: Kyocera P6035cdn error C4600
@TECHKYO, Yes…I saw the service bulletin and did the modifications but the error msg: C4600 still comes back.
-
08-16-2016
#4
Trusted Tech
50+ Posts
- Rep Power
- 18
Re: Kyocera P6035cdn error C4600
unplug the cleaning motor from the pcb
It has been working so far.
-
10-12-2016
#5
Junior Member
- Rep Power
- 0
Re: Kyocera P6035cdn error C4600
-
11-14-2018
#6
Re: Kyocera P6035cdn error C4600
I’ve got a couple of M6535cidn in a very dusty warehouse with the same problem. I’ve unplugged the cleaning motors on both, which got rid of the codes, but I have to manually clean them every few weeks, which is getting old!If replacing the LSUs would make a permanent fix I would gladly do it, but I haven’t seen anything about modifications to them.
So, it’s been a while since you replaced both LSUs… Did that permanently fix the problem???
Thanks for your reply,
Robert B.
Atlanta, GA
-
11-14-2018
#7
Trusted Tech
50+ Posts
- Rep Power
- 26
Re: Kyocera P6035cdn error C4600
We have modified several of this series machines with some success. We have found that the cleaning motor will need to be replaced and possibly the left connect board to eliminate the error code. While replacing the motor, you can modify the lasers with mylar pieces to help the cleaners get on the glass of the laser. This has eliminated the problem on several machines for us. I will post a link to a video that we made describing the modification. I have sent this to Kyocera with no response from them except that they have tried it also with success, but never bothered to let anyone know about it.
https://drive.google.com/open?id=1Bn…ZO9ccRJiJP0WL5
-
01-22-2019
#8
Junior Member
- Rep Power
- 0
Re: Kyocera P6035cdn error C4600
I tried all of the above, but I wasn’t settling on having to go back once a month to pull the 4 devs, 4 drums, belt, 4 toners out and wipe 4 slits of glass because of a unplugged motor. I replaced the «Inner Left Duct» (pn= 302NR33020) which is the black plastic housing for the drive train for all 4 LSU cleaners. Don’t forget to grease those gears either. Fairly easy job after having to pull everything out a dozen times.
Kyocera P6035cdn error C4600Code
4204
Laser output error (Yellow)
The pin photo signal (PDN) is not output
from PD PWB Y for one second while
laser is emitted.
4600
LSU cleaning motor error
When the LSU cleaning motor is driven,
the LSU cleaning motor over-current
detection signal is detected continu-
ously for 50 times (5 s) at 100 ms inter-
vals.
4700
VIDEO ASIC device error
Contents
Causes
Check procedures/corrective measures
Defective harness
Reinsert the connector. Also check for conti-
between APC
nuity within the connector harness. If none,
PWB Y and engine
remedy or replace the harness.
PWB (YC29), or
improper connec-
tor insertion.
Defective APC
Replace the laser scanner unit YK (See
PWB Y.
page 1-5-37).
Defective PD PWB
Replace the laser scanner unit YK (See
Y.
page 1-5-37).
Defective engine
Replace the engine PWB (See page 1-5-
PWB.
29).
Defective harness
Reinsert the connector. Also check for conti-
between LSU
nuity within the connector harness. If none,
cleaning motor and
remedy or replace the harness.
engine PWB
(YC37), or
improper connec-
tor insertion.
Defective drive
Check if the rollers and gears rotate
transmission sys-
smoothly. If not, grease the bushings and
tem of the LSU
gears. Check for broken gears and replace if
cleaning motor.
any.
Defective LSU
Replace the LSU cleaning motor.
cleaning motor.
Defective engine
Replace the engine PWB (See page 1-5-
PWB.
29).
Faulty connection
Check the installation of the main PWB and
of the connector
engine PWB and reinstall them if necessary
between the main
(See page 1-5-28 and 1-5-29).
PWB and engine
PWB.
Defective main
Replace the main PWB (See page 1-5-28).
PWB.
Defective engine
Replace the engine PWB (See page 1-5-
PWB.
29).
Remarks
2K8
1-4-11