Ошибка b0601 hp

Issue Description:

Print cannot boot up into ready state with an error message shown on printer control panel. The error messages include ERROR: B0601/ B0602/ B0603/ B0604/ B0605.

Root Cause:

Firmware crashes.
Note: Inappropriate behavior may cause firmware crash. For example, a printer is turned off when critical firmware update is undergoing.

Solution:

Firmware Update Utility.

note:

This utility can be obtained at hp.com.

There are two use cases when encountering the issue:

  1. P2050 series printer software driver is previously installed on the PC.

    note:

    The instruction have 3 steps and easy to follow as quick fix.

  2. P2050 series printer software driver is NOT previously installed on the PC, such as Dead on Arrival unit.

    note:

    The instruction is only for advanced PC users only as it’s very complicated with 14 steps. Please evaluate the customer knowledge level before helping a customer to do so. Otherwise, replacing formatter is the alternatives.

Instructions for Use case 1: driver is previously installed on PC

  1. Place printer in bootcode mode.

    1. Hold down the Cancel and OK buttons.

    2. Power on printer.

    3. Continue to hold down buttons until control panel dislpays Hewlett-
      Packard on the first line and Bootcode on the second line.

      note:

      Printer is now in bootcode mode
      2.

  2. Ensure printer is connected via USB to PC. Run HP LJ P2055 Firmware
    Update Utility.

    note:

    This utility can be obtained at hp.com.

  3. Select the HP LaserJet P2050 series printer from the dropdown list and click
    Send Firmware button.

    Please observe the printer control panel and verify Downloading Update Data is displayed on control panel followed by Programming App Flash; please wait for
    upgrade utility to finish. Printer would be restarted automatically and the control
    panel display would show Ready.

Then the firmware is now successfully recovered.

Instructions for use case 2: driver is NOT previously installed

  1. Install the driver for HP LaserJet P2050 series printer:

    1. Insert printer installation CD.

    2. In Windows OS, please go to Start, Settings, Printers and Faxes.

    3. Click Add a printer to start Add Printer Wizard as shown blow and
      click on Next button.

    4. Check Local printer attached to this computer box; uncheck
      Automatically detect and Install my Plug and Play printer box and click on
      Next button.

    5. Select FILE:(Print to File) in the Use the following port: dropdown list
      and click on Next button.

    6. Click Have Disk… button.

    7. Browse to the CD drive in which the printer installation CD is inserted
      previously and click OK button.

    8. Highlight the HP LaserJet P2050 Series PCL 6 found in the
      printer installation CD and click on Next button.

    9. Specify the Printer name and click on Next button.

    10. Select No for Do you want to print a test page? and click on Next.

    11. Click the Finish button and allow driver to install as shown below.

    12. Verify printer is listed in Printer and Faxes window as shown below:

  2. Place P2055 in boot code mode:

    1. Hold down the Cancel and OK buttons.

    2. Power on printer.

    3. Continue to hold down buttons until control panel dislpays Hewlett-Packard on the first line and Bootcode on the second line
      Printer is now in bootcode mode.

  3. In the Printer and Faxes window, right click on the HP LaserJet
    P2050 Series PCL6 icon and select Properties.

  4. Click the Ports tab and view the USB ports as shown below.

    note:

    If more than one (USB001) please take note of all listed ports, as other
    installed printers may have USB ports (USB002, USB003, etc).

  5. Close Properties window.

  6. Plug in USB cable from to PC

  7. The Found New Hardware Wizard will pop up, and tje printer USB enumeration will
    happen.

  8. Open printer properties and select Ports tab again.

  9. In ports tab, tick the correct port that the HP LaserJet P2050 series printer is
    enumerated on and click OK.

  10. Click Cancel on Found New Hardware wizard window.

    note:

    Not the driver is installed and it is pointed to correct USB port.

  11. Run HP LJ P2055 Firmware Update Utility.

    note:

    This utility can be obtained
    at hp.com.

  12. Select printer from the dropdown list and click Send Firmware button.

    Please observe the printer control panel and verify Downloading Update Data is
    displayed on control panel followed by Programming App Flash; please wait for
    upgrade utility to finish. Printer would be restarted automatically and the control
    panel display would show Ready. Then the firmware is now successfully
    recovered.

  13. Close New Hardware Found Wizard.

  14. Delete all instances of P2055 printer in Printers and Faxes and run normal
    CD install to install HP LaserJet P2050 series printer drivers properly from printer
    installation CD.

Источник

Issue Description:

Print cannot boot up into ready state with an error message shown on printer control panel. The error messages include ERROR: B0601/ B0602/ B0603/ B0604/ B0605.

Root Cause:

Firmware crashes.
Note: Inappropriate behavior may cause firmware crash. For example, a printer is turned off when critical firmware update is undergoing.

Solution:

Firmware Update Utility.

note:

This utility can be obtained at hp.com.

There are two use cases when encountering the issue:

  1. P2050 series printer software driver is previously installed on the PC.

    note:

    The instruction have 3 steps and easy to follow as quick fix.

  2. P2050 series printer software driver is NOT previously installed on the PC, such as Dead on Arrival unit.

    note:

    The instruction is only for advanced PC users only as it’s very complicated with 14 steps. Please evaluate the customer knowledge level before helping a customer to do so. Otherwise, replacing formatter is the alternatives.

Instructions for Use case 1: driver is previously installed on PC

  1. Place printer in bootcode mode.

    1. Hold down the Cancel and OK buttons.

    2. Power on printer.

    3. Continue to hold down buttons until control panel dislpays Hewlett-
      Packard on the first line and Bootcode on the second line.

      note:

      Printer is now in bootcode mode
      2.

  2. Ensure printer is connected via USB to PC. Run HP LJ P2055 Firmware
    Update Utility.

    note:

    This utility can be obtained at hp.com.

  3. Select the HP LaserJet P2050 series printer from the dropdown list and click
    Send Firmware button.

    Please observe the printer control panel and verify Downloading Update Data is displayed on control panel followed by Programming App Flash; please wait for
    upgrade utility to finish. Printer would be restarted automatically and the control
    panel display would show Ready.

Then the firmware is now successfully recovered.

Instructions for use case 2: driver is NOT previously installed

  1. Install the driver for HP LaserJet P2050 series printer:

    1. Insert printer installation CD.

    2. In Windows OS, please go to Start, Settings, Printers and Faxes.

    3. Click Add a printer to start Add Printer Wizard as shown blow and
      click on Next button.

    4. Check Local printer attached to this computer box; uncheck
      Automatically detect and Install my Plug and Play printer box and click on
      Next button.

    5. Select FILE:(Print to File) in the Use the following port: dropdown list
      and click on Next button.

    6. Click Have Disk… button.

    7. Browse to the CD drive in which the printer installation CD is inserted
      previously and click OK button.

    8. Highlight the HP LaserJet P2050 Series PCL 6 found in the
      printer installation CD and click on Next button.

    9. Specify the Printer name and click on Next button.

    10. Select No for Do you want to print a test page? and click on Next.

    11. Click the Finish button and allow driver to install as shown below.

    12. Verify printer is listed in Printer and Faxes window as shown below:

  2. Place P2055 in boot code mode:

    1. Hold down the Cancel and OK buttons.

    2. Power on printer.

    3. Continue to hold down buttons until control panel dislpays Hewlett-Packard on the first line and Bootcode on the second line
      Printer is now in bootcode mode.

  3. In the Printer and Faxes window, right click on the HP LaserJet
    P2050 Series PCL6 icon and select Properties.

  4. Click the Ports tab and view the USB ports as shown below.

    note:

    If more than one (USB001) please take note of all listed ports, as other
    installed printers may have USB ports (USB002, USB003, etc).

  5. Close Properties window.

  6. Plug in USB cable from to PC

  7. The Found New Hardware Wizard will pop up, and tje printer USB enumeration will
    happen.

  8. Open printer properties and select Ports tab again.

  9. In ports tab, tick the correct port that the HP LaserJet P2050 series printer is
    enumerated on and click OK.

  10. Click Cancel on Found New Hardware wizard window.

    note:

    Not the driver is installed and it is pointed to correct USB port.

  11. Run HP LJ P2055 Firmware Update Utility.

    note:

    This utility can be obtained
    at hp.com.

  12. Select printer from the dropdown list and click Send Firmware button.

    Please observe the printer control panel and verify Downloading Update Data is
    displayed on control panel followed by Programming App Flash; please wait for
    upgrade utility to finish. Printer would be restarted automatically and the control
    panel display would show Ready. Then the firmware is now successfully
    recovered.

  13. Close New Hardware Found Wizard.

  14. Delete all instances of P2055 printer in Printers and Faxes and run normal
    CD install to install HP LaserJet P2050 series printer drivers properly from printer
    installation CD.

Источник

Перейти к контенту

Issue Description:

Print cannot boot up into ready state with an error message shown on printer control panel. The error messages include ERROR: B0601/ B0602/ B0603/ B0604/ B0605.

Root Cause:

Firmware crashes.
Note: Inappropriate behavior may cause firmware crash. For example, a printer is turned off when critical firmware update is undergoing.

Solution:

Firmware Update Utility.

note:

This utility can be obtained at hp.com.

There are two use cases when encountering the issue:

  1. P2050 series printer software driver is previously installed on the PC.

    note:

    The instruction have 3 steps and easy to follow as quick fix.

  2. P2050 series printer software driver is NOT previously installed on the PC, such as Dead on Arrival unit.

    note:

    The instruction is only for advanced PC users only as it’s very complicated with 14 steps. Please evaluate the customer knowledge level before helping a customer to do so. Otherwise, replacing formatter is the alternatives.

Instructions for Use case 1: driver is previously installed on PC

  1. Place printer in bootcode mode.

    1. Hold down the Cancel and OK buttons.

    2. Power on printer.

    3. Continue to hold down buttons until control panel dislpays Hewlett-
      Packard on the first line and Bootcode on the second line.

      note:

      Printer is now in bootcode mode
      2.

  2. Ensure printer is connected via USB to PC. Run HP LJ P2055 Firmware
    Update Utility.

    note:

    This utility can be obtained at hp.com.

  3. Select the HP LaserJet P2050 series printer from the dropdown list and click
    Send Firmware button.

    Please observe the printer control panel and verify Downloading Update Data is displayed on control panel followed by Programming App Flash; please wait for
    upgrade utility to finish. Printer would be restarted automatically and the control
    panel display would show Ready.

Then the firmware is now successfully recovered.

Instructions for use case 2: driver is NOT previously installed

  1. Install the driver for HP LaserJet P2050 series printer:

    1. Insert printer installation CD.

    2. In Windows OS, please go to Start, Settings, Printers and Faxes.

    3. Click Add a printer to start Add Printer Wizard as shown blow and
      click on Next button.

    4. Check Local printer attached to this computer box; uncheck
      Automatically detect and Install my Plug and Play printer box and click on
      Next button.

    5. Select FILE:(Print to File) in the Use the following port: dropdown list
      and click on Next button.

    6. Click Have Disk… button.

    7. Browse to the CD drive in which the printer installation CD is inserted
      previously and click OK button.

    8. Highlight the HP LaserJet P2050 Series PCL 6 found in the
      printer installation CD and click on Next button.

    9. Specify the Printer name and click on Next button.

    10. Select No for Do you want to print a test page? and click on Next.

    11. Click the Finish button and allow driver to install as shown below.

    12. Verify printer is listed in Printer and Faxes window as shown below:

  2. Place P2055 in boot code mode:

    1. Hold down the Cancel and OK buttons.

    2. Power on printer.

    3. Continue to hold down buttons until control panel dislpays Hewlett-Packard on the first line and Bootcode on the second line
      Printer is now in bootcode mode.

  3. In the Printer and Faxes window, right click on the HP LaserJet
    P2050 Series PCL6 icon and select Properties.

  4. Click the Ports tab and view the USB ports as shown below.

    note:

    If more than one (USB001) please take note of all listed ports, as other
    installed printers may have USB ports (USB002, USB003, etc).

  5. Close Properties window.

  6. Plug in USB cable from to PC

  7. The Found New Hardware Wizard will pop up, and tje printer USB enumeration will
    happen.

  8. Open printer properties and select Ports tab again.

  9. In ports tab, tick the correct port that the HP LaserJet P2050 series printer is
    enumerated on and click OK.

  10. Click Cancel on Found New Hardware wizard window.

    note:

    Not the driver is installed and it is pointed to correct USB port.

  11. Run HP LJ P2055 Firmware Update Utility.

    note:

    This utility can be obtained
    at hp.com.

  12. Select printer from the dropdown list and click Send Firmware button.

    Please observe the printer control panel and verify Downloading Update Data is
    displayed on control panel followed by Programming App Flash; please wait for
    upgrade utility to finish. Printer would be restarted automatically and the control
    panel display would show Ready. Then the firmware is now successfully
    recovered.

  13. Close New Hardware Found Wizard.

  14. Delete all instances of P2055 printer in Printers and Faxes and run normal
    CD install to install HP LaserJet P2050 series printer drivers properly from printer
    installation CD.

Specs:

— HP Laserjet P2055dn

— Installed drivers to Windows 7, 32-bit

— Error Code given by HP Printer:  B0605

— Downloaded newest firmware update from HP.com tech support site

— Here’s the website in which I downloaded the firmware update — http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=3662058&sp…

— Connect printer USB, specified it as the USB port in the printer properties as well

— Booted up printer while pressing «OK» and «Cancel» as suggested

— Ran update

— During installation, it says on printer interface that it is «Downloading update»

— Afterwards I get «Bad FLASH Burn Power Cycle»

Any help on this?  I cannot get this printer up and running.  It’s relatively new as well, but somehow isn’t under warranty.

I sent an email to HP.com as well, but am still awaiting reply.  (Attached is the firmware update that I tried)

If you have an HP printer wherein you are encountering the B0605 error, then you must know how to fix the issue. Mostly HP printers work efficiently and are brilliant devices that are used both in offices and homes. However, just like any machine, it tends to show errors. If you are facing a B0605 error printer, then either you can troubleshoot the same by yourself, or you can reach on the Customer Care number to talk with the experts. If you are planning to troubleshoot the problem, then this blog is meant for you.

Reason for the error-

The specific reason due to which the error flashes is because the firmware gets crashed or because of the incapability of the booting process in the ready state. Below is enlisted the method that will help in solving the issue. It is important that the troubleshoot is done carefully. Mentioned under two  method. One is when the printer software driver is already on the PC and another when it is not found on the PC. You can select the type as per your requirement.

Placing printer in boot mode-

Type 1-

This method works when the printer software driver is already installed on the PC. Steps to be undertaken under this type are-

  1. a) Placing printer in boot code mode- In this step, the printer is placed in the boot code mode. For this, the cancel and ok buttons are held down. For activating this mode, these buttons have to be held while the printer is switched on.
  2. b) Ensure connectivity- One needs to ensure that the printer is connected to PC along USB.
  3. c) Option selection- This is the last step of the method where the HP printer is selected from the drop-down list and send firmware button is clicked.

Type 2-

In this type, the printer software driver is not found on the PC. The steps under this type are-

  1. a) Push in the CD of printer installation
  2. b) Move to start, select settings and from options click Printers and faxes
  3. c) Select options to add a printer and then select next
  4. d) Check for any local printer connected to your computer, disallow automatic detection option and install the plug and play printer. Select the next button after following all steps.
  5. e) Choose file and select have disk button
  6. f) Browse to find the CD drive in which printer installation CD is inserted, click okay when found.
  7. g) Select printer installation CD and move to the next button.
  8. h) Specify the name of the printer, move to next
  9. i) Click no followed with next selecting finish button at last.
  10. j) Once done verify if the printer is listed in printer and Faxes window.
  11. k) On printer and faxes window, click properties that appear as you right click on the printer.
  12. l) Select ports tab and see USB sort
  13. m) Close new hardware found wizard as it appears.

If you find yourself unable to solve the issue by following either of the two solutions, it is recommended that an expert’s help is taken. But we are positive this should answer your query on How to Fix HP Printer Error b0605

Перейти к контенту

Issue Description:

Print cannot boot up into ready state with an error message shown on printer control panel. The error messages include ERROR: B0601/ B0602/ B0603/ B0604/ B0605.

Root Cause:

Firmware crashes.
Note: Inappropriate behavior may cause firmware crash. For example, a printer is turned off when critical firmware update is undergoing.

Solution:

Firmware Update Utility.

note:

This utility can be obtained at hp.com.

There are two use cases when encountering the issue:

  1. P2050 series printer software driver is previously installed on the PC.

    note:

    The instruction have 3 steps and easy to follow as quick fix.

  2. P2050 series printer software driver is NOT previously installed on the PC, such as Dead on Arrival unit.

    note:

    The instruction is only for advanced PC users only as it’s very complicated with 14 steps. Please evaluate the customer knowledge level before helping a customer to do so. Otherwise, replacing formatter is the alternatives.

Instructions for Use case 1: driver is previously installed on PC

  1. Place printer in bootcode mode.

    1. Hold down the Cancel and OK buttons.

    2. Power on printer.

    3. Continue to hold down buttons until control panel dislpays Hewlett-
      Packard on the first line and Bootcode on the second line.

      note:

      Printer is now in bootcode mode
      2.

  2. Ensure printer is connected via USB to PC. Run HP LJ P2055 Firmware
    Update Utility.

    note:

    This utility can be obtained at hp.com.

  3. Select the HP LaserJet P2050 series printer from the dropdown list and click
    Send Firmware button.

    Please observe the printer control panel and verify Downloading Update Data is displayed on control panel followed by Programming App Flash; please wait for
    upgrade utility to finish. Printer would be restarted automatically and the control
    panel display would show Ready.

Then the firmware is now successfully recovered.

Instructions for use case 2: driver is NOT previously installed

  1. Install the driver for HP LaserJet P2050 series printer:

    1. Insert printer installation CD.

    2. In Windows OS, please go to Start, Settings, Printers and Faxes.

    3. Click Add a printer to start Add Printer Wizard as shown blow and
      click on Next button.

    4. Check Local printer attached to this computer box; uncheck
      Automatically detect and Install my Plug and Play printer box and click on
      Next button.

    5. Select FILE:(Print to File) in the Use the following port: dropdown list
      and click on Next button.

    6. Click Have Disk… button.

    7. Browse to the CD drive in which the printer installation CD is inserted
      previously and click OK button.

    8. Highlight the HP LaserJet P2050 Series PCL 6 found in the
      printer installation CD and click on Next button.

    9. Specify the Printer name and click on Next button.

    10. Select No for Do you want to print a test page? and click on Next.

    11. Click the Finish button and allow driver to install as shown below.

    12. Verify printer is listed in Printer and Faxes window as shown below:

  2. Place P2055 in boot code mode:

    1. Hold down the Cancel and OK buttons.

    2. Power on printer.

    3. Continue to hold down buttons until control panel dislpays Hewlett-Packard on the first line and Bootcode on the second line
      Printer is now in bootcode mode.

  3. In the Printer and Faxes window, right click on the HP LaserJet
    P2050 Series PCL6 icon and select Properties.

  4. Click the Ports tab and view the USB ports as shown below.

    note:

    If more than one (USB001) please take note of all listed ports, as other
    installed printers may have USB ports (USB002, USB003, etc).

  5. Close Properties window.

  6. Plug in USB cable from to PC

  7. The Found New Hardware Wizard will pop up, and tje printer USB enumeration will
    happen.

  8. Open printer properties and select Ports tab again.

  9. In ports tab, tick the correct port that the HP LaserJet P2050 series printer is
    enumerated on and click OK.

  10. Click Cancel on Found New Hardware wizard window.

    note:

    Not the driver is installed and it is pointed to correct USB port.

  11. Run HP LJ P2055 Firmware Update Utility.

    note:

    This utility can be obtained
    at hp.com.

  12. Select printer from the dropdown list and click Send Firmware button.

    Please observe the printer control panel and verify Downloading Update Data is
    displayed on control panel followed by Programming App Flash; please wait for
    upgrade utility to finish. Printer would be restarted automatically and the control
    panel display would show Ready. Then the firmware is now successfully
    recovered.

  13. Close New Hardware Found Wizard.

  14. Delete all instances of P2055 printer in Printers and Faxes and run normal
    CD install to install HP LaserJet P2050 series printer drivers properly from printer
    installation CD.

Модератор: vetal

Прилепить пост

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑HP LJ P2055dn Ошибка B0605, плате форматтера нужно новое встроенное программное обеспечение, но порт USB поврежден. Уведомление от технической поддержки HP не поможет мне. Я судимое ожог чип, но та же проблема.

error B0605 , formatter board need new firmware but USB port is broken. Notice from HP support not help me. I tryed burn chip on formatter board ,but same problem?

Аватар пользователя

3cxmoskva

Собрал картридж правильно

  • Не в сети

Прилепить пост

Сообщение Dani » Вт янв 17, 2017 9:10 am

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑Эта статья Вам не помогла?

This article didn’t help you?

Всё как то так ну или типа того

Аватар пользователя

Dani

Понюхал тонер

  • Не в сети
  • ip4500 ошибка 6А00 «AP position error»

    vodkin в форуме Принтеры струйные

    3
    4454

    vodkin
    Перейти к последнему сообщению
    Пн мар 19, 2012 5:22 am
  • Samsung CLX-3175 во время запуска пишет «Image error Resset»

    mr_sasha в форуме Принтеры, МФУ, факсы, копиры формата A4

    9
    5254

    maisterko
    Перейти к последнему сообщению
    Пн дек 14, 2015 4:19 pm
  • Установка Fuser Unit (печки) в Kyocera 5500i при error C6040

    Engine в форуме Принтеры, МФУ, копиры формата A3

    0
    2448

    Engine
    Перейти к последнему сообщению
    Вт фев 05, 2019 11:14 am
  • Brother HL-2030R — Hight Voltage Error (Drum+Toner)

    lev91 в форуме Принтеры, МФУ, факсы, копиры формата A4

    11
    9872

    kvg
    Перейти к последнему сообщению
    Вс авг 26, 2012 3:32 pm
  • Epson L800 0x50 cr home position seeking error

    glam1112 в форуме Принтеры струйные

    2
    3601

    3cxmoskva
    Перейти к последнему сообщению
    Пн мар 12, 2018 3:28 pm

Вернуться в Принтеры, МФУ, факсы, копиры формата A4

Кто сейчас на форуме

Сейчас этот форум просматривают: darknebola и гости: 123

You may see hp printer error b0605 error message popping up if the firmware of your printer gets crashed. Firmware gets crashed due to inappropriate behaviour, like: turning off the printer while the vital firmware update one is going on. This issue could be resolved by following the troubleshooting steps, like get the firmware re-flash in the BootCode mode and after that try rebooting your printer. Though firmware re-flash won’t help always, but yes, it is one of the best major you can take as a first step. If the HP Printer Error Message is displayed then your printer won’t be booted up in the ready state.

HP Printer Error B0605

Causes B0605 Error Message HP Printer

Causes:

There might be two causes due to which this error is received:

  • You have installed the software driver of P2050 series printer on the PC previously
  • Software driver of P2050 series printer is not installed previously on the computer

Instruction

Case 1: Installation of driver was done previously on PC

  1. Ensure that printer is places in the bootcode mode
  • Keep holding the OK and Cancel buttons
  • Keep the power of the printer ON
  • Make sure that you are holding the buttons till the time Hewlett-Packard in first line and the Bootcode in second line is not displayed by the control panel
  1. Check carefully that your printer is connected to the PC through USB. After that run the firmware HP LJ P2055
  2. Now go to the dropdown list and after that click on the button of Send Firmware

Observe the panel of printer control carefully and make sure that on the control panel Downloading Update Data is flashing up along with the Programming App Flash. Wait, till the time upgrade utility gets finished. Your printer will be automatically restarted, and you will be able to see, Ready, displayed on control panel.

This means your firmware is recovered successfully.

Case 2: Installation of driver is not done previously

  1. Install the driver
  • Then get the printer installation CD inserted to it
  • After that go to the Start first and then to Settings and then to Printers and Faxes in Windows Operating System
  • In order to get the Add Printer Wizard started click on the Add a Printer, and then click on the Next button
  • Then check the local printer that is attached with the computer system. After that make sure that you remove the checkmark from Install my Plug and Play printer and Automatically detect box and then hit the Next button
  • Then go to the port of Use the following and select the FILE and tap on the Next button
  • After that, click on the button of Have Disk
  • Go to the CD Drive and browse it, where the printer installation CD was previously inserted. Click on the OK button
  • Click on the next button by highlighting the HP Laser Jet present in installation CD of printer. After that tap the Next button
  • By specifying the name of the Printer, hit the Next button
  • When, DO you want to print a test page? pop up, click on NO and then tap on Next
  • Click on the button saying Finish, and let the driver install
  • You will see that Verify printer is present in the window of Printer and Faxes
  1. Placing the P2055 in the bootcode mode
  • Keep holding the OK and Cancel buttons
  • Turn on the power of the printer
  • Keep on holding the buttons, until you see the display of the control panel flashing Hewlett-Packard in top line and Bootcode displaying on second line. Your printer is now in the mode of bootcode
  1. Go to the window of Printer and Faxes and on the icon of the HP LaserJet P2050 Series PCL6, do right click and choose the Properties
  2. Then by clicking on the tab of Ports you can see USB ports
  3. After that get the Property window closed
  4. Then ensure that USB cable is plugin from PC
  5. You will see the Found New Hardware Wizard popping up and enumeration of USB will start taking place
  6. Then open the Printer Properties again and choose the tab of Ports again
  7. Then tick mark the correct port in ports tab
  8. Click on Cancel if the window of Found New Hardware Wizard pop ups.
  9. Run the Firmware Update Utility
  10. Now from the drop down choose the printer and then tap on the button of Send Firmware
  11. Keep a close eye on the control panel and make sure that control panel is flashing the Downloading Update Data along with the Programming App Flash. Wait till the time upgrade utility gets finished. Automatically the printer will be restarted and you will be able to see, Ready, flashing on the display of control panel. The firmware is recovered successfully
  12. Close the New Found Hardware Wizard

Troubleshooting Steps HP Printer Error B0605

Troubleshooting the Printer Error B0605:

Step 1: Get the Firewall upgraded of the Printer

  • First of all, get the correct firmware downloaded
  • Then reload the upgraded and basic firmware
  • Pull the power cord and turn off the power of the printer and let it remain same for few seconds
  • Plug in back and get the printer started up
  • Check whether the error is removed or not. In case it is not, then try the next step

Step 2: Reinstalling the toner by removing it first

  • Disconnect and turnoff the printer’s power source
  • After that remove the toner mesh and paper tray as well
  • Turn on the power of the unit for at least 50 to 60 seconds and then turn the power off again
  • Get the paper tray and toner mesh installed again
  • Turn on the power of the unit and make sure that the power is up of the unit before getting the test page printed

Step 3: Reflashing firmware

  • Enter the boot mode and make sure that firmware is reflashed, also reboot the printer
  • This reflashing will help you to get rid of the error

Scope of Services

  • Advanced Printer Tech Support through experienced professionals
  • Immediate resolution of all the technical issues
  • Tech savvy and self-motivated staff
  • Capable of providing the customized solutions Dial Now Technical Support For Printer

May 30, 2018November 28, 2019

If you have an HP printer wherein you are encountering the B0605 error, then you must know how to fix the issue. Mostly HP printers work efficiently and are brilliant devices that are used both in offices and homes. However, just like any machine, it tends to show errors. If you are facing a B0605 error printer, then either you can troubleshoot the same by yourself, or you can reach on the Customer Care number to talk with the experts. If you are planning to troubleshoot the problem, then this blog is meant for you.

Reason for the error-

The specific reason due to which the error flashes is because the firmware gets crashed or because of the incapability of the booting process in the ready state. Below is enlisted the method that will help in solving the issue. It is important that the troubleshoot is done carefully. Mentioned under two  method. One is when the printer software driver is already on the PC and another when it is not found on the PC. You can select the type as per your requirement.

Placing printer in boot mode-

Type 1-

This method works when the printer software driver is already installed on the PC. Steps to be undertaken under this type are-

  1. a) Placing printer in boot code mode- In this step, the printer is placed in the boot code mode. For this, the cancel and ok buttons are held down. For activating this mode, these buttons have to be held while the printer is switched on.
  2. b) Ensure connectivity- One needs to ensure that the printer is connected to PC along USB.
  3. c) Option selection- This is the last step of the method where the HP printer is selected from the drop-down list and send firmware button is clicked.

Type 2-

In this type, the printer software driver is not found on the PC. The steps under this type are-

  1. a) Push in the CD of printer installation
  2. b) Move to start, select settings and from options click Printers and faxes
  3. c) Select options to add a printer and then select next
  4. d) Check for any local printer connected to your computer, disallow automatic detection option and install the plug and play printer. Select the next button after following all steps.
  5. e) Choose file and select have disk button
  6. f) Browse to find the CD drive in which printer installation CD is inserted, click okay when found.
  7. g) Select printer installation CD and move to the next button.
  8. h) Specify the name of the printer, move to next
  9. i) Click no followed with next selecting finish button at last.
  10. j) Once done verify if the printer is listed in printer and Faxes window.
  11. k) On printer and faxes window, click properties that appear as you right click on the printer.
  12. l) Select ports tab and see USB sort
  13. m) Close new hardware found wizard as it appears.

If you find yourself unable to solve the issue by following either of the two solutions, it is recommended that an expert’s help is taken. But we are positive this should answer your query on How to Fix HP Printer Error b0605

You may see hp printer error b0605 error message popping up if the firmware of your printer gets crashed. Firmware gets crashed due to inappropriate behaviour, like: turning off the printer while the vital firmware update one is going on. This issue could be resolved by following the troubleshooting steps, like get the firmware re-flash in the BootCode mode and after that try rebooting your printer. Though firmware re-flash won’t help always, but yes, it is one of the best major you can take as a first step. If the HP Printer Error Message is displayed then your printer won’t be booted up in the ready state.

HP Printer Error B0605

Causes B0605 Error Message HP Printer

Causes:

There might be two causes due to which this error is received:

  • You have installed the software driver of P2050 series printer on the PC previously
  • Software driver of P2050 series printer is not installed previously on the computer

Instruction

Case 1: Installation of driver was done previously on PC

  1. Ensure that printer is places in the bootcode mode
  • Keep holding the OK and Cancel buttons
  • Keep the power of the printer ON
  • Make sure that you are holding the buttons till the time Hewlett-Packard in first line and the Bootcode in second line is not displayed by the control panel
  1. Check carefully that your printer is connected to the PC through USB. After that run the firmware HP LJ P2055
  2. Now go to the dropdown list and after that click on the button of Send Firmware

Observe the panel of printer control carefully and make sure that on the control panel Downloading Update Data is flashing up along with the Programming App Flash. Wait, till the time upgrade utility gets finished. Your printer will be automatically restarted, and you will be able to see, Ready, displayed on control panel.

This means your firmware is recovered successfully.

Case 2: Installation of driver is not done previously

  1. Install the driver
  • Then get the printer installation CD inserted to it
  • After that go to the Start first and then to Settings and then to Printers and Faxes in Windows Operating System
  • In order to get the Add Printer Wizard started click on the Add a Printer, and then click on the Next button
  • Then check the local printer that is attached with the computer system. After that make sure that you remove the checkmark from Install my Plug and Play printer and Automatically detect box and then hit the Next button
  • Then go to the port of Use the following and select the FILE and tap on the Next button
  • After that, click on the button of Have Disk
  • Go to the CD Drive and browse it, where the printer installation CD was previously inserted. Click on the OK button
  • Click on the next button by highlighting the HP Laser Jet present in installation CD of printer. After that tap the Next button
  • By specifying the name of the Printer, hit the Next button
  • When, DO you want to print a test page? pop up, click on NO and then tap on Next
  • Click on the button saying Finish, and let the driver install
  • You will see that Verify printer is present in the window of Printer and Faxes
  1. Placing the P2055 in the bootcode mode
  • Keep holding the OK and Cancel buttons
  • Turn on the power of the printer
  • Keep on holding the buttons, until you see the display of the control panel flashing Hewlett-Packard in top line and Bootcode displaying on second line. Your printer is now in the mode of bootcode
  1. Go to the window of Printer and Faxes and on the icon of the HP LaserJet P2050 Series PCL6, do right click and choose the Properties
  2. Then by clicking on the tab of Ports you can see USB ports
  3. After that get the Property window closed
  4. Then ensure that USB cable is plugin from PC
  5. You will see the Found New Hardware Wizard popping up and enumeration of USB will start taking place
  6. Then open the Printer Properties again and choose the tab of Ports again
  7. Then tick mark the correct port in ports tab
  8. Click on Cancel if the window of Found New Hardware Wizard pop ups.
  9. Run the Firmware Update Utility
  10. Now from the drop down choose the printer and then tap on the button of Send Firmware
  11. Keep a close eye on the control panel and make sure that control panel is flashing the Downloading Update Data along with the Programming App Flash. Wait till the time upgrade utility gets finished. Automatically the printer will be restarted and you will be able to see, Ready, flashing on the display of control panel. The firmware is recovered successfully
  12. Close the New Found Hardware Wizard

Troubleshooting Steps HP Printer Error B0605

Troubleshooting the Printer Error B0605:

Step 1: Get the Firewall upgraded of the Printer

  • First of all, get the correct firmware downloaded
  • Then reload the upgraded and basic firmware
  • Pull the power cord and turn off the power of the printer and let it remain same for few seconds
  • Plug in back and get the printer started up
  • Check whether the error is removed or not. In case it is not, then try the next step

Step 2: Reinstalling the toner by removing it first

  • Disconnect and turnoff the printer’s power source
  • After that remove the toner mesh and paper tray as well
  • Turn on the power of the unit for at least 50 to 60 seconds and then turn the power off again
  • Get the paper tray and toner mesh installed again
  • Turn on the power of the unit and make sure that the power is up of the unit before getting the test page printed

Step 3: Reflashing firmware

  • Enter the boot mode and make sure that firmware is reflashed, also reboot the printer
  • This reflashing will help you to get rid of the error

Scope of Services

  • Advanced Printer Tech Support through experienced professionals
  • Immediate resolution of all the technical issues
  • Tech savvy and self-motivated staff
  • Capable of providing the customized solutions Dial Now Technical Support For Printer

May 30, 2018November 28, 2019

Источник

Skip to content

Home  »  HP   »   How to Fix HP printer Error B0601

Generally, different printers show/display different errors, depending upon their type, their way of functioning and the type of the devices they are connected to. The main step in resolving a problem or display of error is identifying the problem.

For example, you may have an error of ink system failure, but the process you are following is to resolve the error for a battery operated power failure. This would not help you in any possible way, and you will just waste your precious time. So in order to save your time that this article will come in handy.

ISSUE DESCRIPTION : The B0601 error generally shows up when print cannot boot up into the ready state with an error message shown on the printer control panel which is the B0601 error. Now we have identified that this type of error is a booting up error related to the operating system of the printer.

ROOT CAUSE : The next step is to find the root cause for the error. This type of HP printer Error B0601 is generated when the firmware of the printer crashes. Inappropriate behavior may cause the firmware to crash and even turning off the printer when the critical firmware update is undergoing can prove very delicate in these matters.

The next million dollar question is “How to fix HP printer error B0601”

Here are a few ways on how to fix the error:

  1. UPDATE FIRMWARE UTILITY: You need to update your firmware utility in order to resolve the error. This utility update can be obtained at hp.com, and generally, further there are two cases when you encounter such an issue, and both are discussed as follows: -> A printer software driver for the P2050 series is previously installed on the PC.-> P2050 series printer software driver has NOT been installed installed on the PC, such as Dead on Arrival unit.
  2. INSTRUCTIONS FOR USE CASE 01: the P2050 driver is previously installed on PC:
    Place printer in boot code mode.
    1. Hold down the Cancel and OK buttons.
    2. Power on the printer.
    3. Continue to hold down buttons until the control panel displays Hewlett- Packard on the first line and Boot code on the second line.
    4. Ensure printer is connected via USB to the PC. Run HP LJ P2055 Firmware Update Utility.
    5. From the drop-down list, select the HP LaserJet P2050 series printer and click on the Send Firmware

Then the firmware is now successfully recovered.

After going through this process from step to step, you will find that once the firmware is successfully recovered, the error displayed on the control panel of the printer is now resolved.

But if still, the problem persists, delete all the instances and files present of the P2055 printer in the Printers and Faxes and run the normal CD again to install the HP LaserJet drivers properly from the installation CD.

Источник

Issue Description:

Print cannot boot up into ready state with an error message shown on printer control panel. The error messages include ERROR: B0601/ B0602/ B0603/ B0604/ B0605.

Root Cause:

Firmware crashes.
Note: Inappropriate behavior may cause firmware crash. For example, a printer is turned off when critical firmware update is undergoing.

Solution:

Firmware Update Utility.

note:

This utility can be obtained at hp.com.

There are two use cases when encountering the issue:

  1. P2050 series printer software driver is previously installed on the PC.

    note:

    The instruction have 3 steps and easy to follow as quick fix.

  2. P2050 series printer software driver is NOT previously installed on the PC, such as Dead on Arrival unit.

    note:

    The instruction is only for advanced PC users only as it’s very complicated with 14 steps. Please evaluate the customer knowledge level before helping a customer to do so. Otherwise, replacing formatter is the alternatives.

Instructions for Use case 1: driver is previously installed on PC

  1. Place printer in bootcode mode.

    1. Hold down the Cancel and OK buttons.

    2. Power on printer.

    3. Continue to hold down buttons until control panel dislpays Hewlett-
      Packard on the first line and Bootcode on the second line.

      note:

      Printer is now in bootcode mode
      2.

  2. Ensure printer is connected via USB to PC. Run HP LJ P2055 Firmware
    Update Utility.

    note:

    This utility can be obtained at hp.com.

  3. Select the HP LaserJet P2050 series printer from the dropdown list and click
    Send Firmware button.

    Please observe the printer control panel and verify Downloading Update Data is displayed on control panel followed by Programming App Flash; please wait for
    upgrade utility to finish. Printer would be restarted automatically and the control
    panel display would show Ready.

Then the firmware is now successfully recovered.

Instructions for use case 2: driver is NOT previously installed

  1. Install the driver for HP LaserJet P2050 series printer:

    1. Insert printer installation CD.

    2. In Windows OS, please go to Start, Settings, Printers and Faxes.

    3. Click Add a printer to start Add Printer Wizard as shown blow and
      click on Next button.

    4. Check Local printer attached to this computer box; uncheck
      Automatically detect and Install my Plug and Play printer box and click on
      Next button.

    5. Select FILE:(Print to File) in the Use the following port: dropdown list
      and click on Next button.

    6. Click Have Disk… button.

    7. Browse to the CD drive in which the printer installation CD is inserted
      previously and click OK button.

    8. Highlight the HP LaserJet P2050 Series PCL 6 found in the
      printer installation CD and click on Next button.

    9. Specify the Printer name and click on Next button.

    10. Select No for Do you want to print a test page? and click on Next.

    11. Click the Finish button and allow driver to install as shown below.

    12. Verify printer is listed in Printer and Faxes window as shown below:

  2. Place P2055 in boot code mode:

    1. Hold down the Cancel and OK buttons.

    2. Power on printer.

    3. Continue to hold down buttons until control panel dislpays Hewlett-Packard on the first line and Bootcode on the second line
      Printer is now in bootcode mode.

  3. In the Printer and Faxes window, right click on the HP LaserJet
    P2050 Series PCL6 icon and select Properties.

  4. Click the Ports tab and view the USB ports as shown below.

    note:

    If more than one (USB001) please take note of all listed ports, as other
    installed printers may have USB ports (USB002, USB003, etc).

  5. Close Properties window.

  6. Plug in USB cable from to PC

  7. The Found New Hardware Wizard will pop up, and tje printer USB enumeration will
    happen.

  8. Open printer properties and select Ports tab again.

  9. In ports tab, tick the correct port that the HP LaserJet P2050 series printer is
    enumerated on and click OK.

  10. Click Cancel on Found New Hardware wizard window.

    note:

    Not the driver is installed and it is pointed to correct USB port.

  11. Run HP LJ P2055 Firmware Update Utility.

    note:

    This utility can be obtained
    at hp.com.

  12. Select printer from the dropdown list and click Send Firmware button.

    Please observe the printer control panel and verify Downloading Update Data is
    displayed on control panel followed by Programming App Flash; please wait for
    upgrade utility to finish. Printer would be restarted automatically and the control
    panel display would show Ready. Then the firmware is now successfully
    recovered.

  13. Close New Hardware Found Wizard.

  14. Delete all instances of P2055 printer in Printers and Faxes and run normal
    CD install to install HP LaserJet P2050 series printer drivers properly from printer
    installation CD.

Содержание

  1. Error b0605 hp 2055
  2. Error b0605 hp 2055
  3. Error b0605 hp 2055
  4. HP Printer Error B0605
  5. B0605 Error Code HP Printer
  6. Causes B0605 Error Message HP Printer
  7. Troubleshooting Steps HP Printer Error B0605

Error b0605 hp 2055

КОНФЕРЕНЦИЯ СТАРТКОПИ
Принтеры, копировальные аппараты, МФУ, факсы и другая офисная техника:
вопросы ремонта, обслуживания, заправки, выбора

На весь ресурс всего пара тем об этой ошибке. И никакого внятного ответа. Кто нибудь сталкивался так, что бы решить эту проблему? Новый форматер — это конечно хорошо. Но как то это не серьезно.

DOMKRAT (0): как то это не серьезно
?? Желаете его поремонтить??))

Угумс, а вы мне бразер припоминаете ?)))

Нет, уточняю ваши намерения и интересуюсь конкретными планами)

(0) А можно фото ошибки с дисплея . желательно на английском.

Все. Готов он. Прошил я его. Хоть это и муторно и не с первого раза я все понял (все ж по англицки, по русски нема подсказок) — но как на официалах написано — так и есть. Треба шить — значт надо шить. А вот греть форматер как оказалось не надо вовсе, как это в одной из двух темок советовалось.

Ну-ну. Греть вас никто, конечно, не заставляет. Но если вы с этой ошибкой ни разу до этого не разбирались, а теперь прошили, и, обрадовавшись и взямши за это денежку, отдадите его, то будьте готовы к повторному приносу тела недовольным клиентом, и там уже прошивка вам вряд ли чем поможет, а клиенту придётся объяснять, за что вы прошлый раз взяли деньги и почему теперь надо гораздо больше денег, чтоб оживить трупа. Потому что изначальная проблема на 90% совсем не в прошивке. На вашем месте я бы предупредил клиента, что склероз, скорее всего, будет прогрессировать и взял бы за ремонт чисто символически.

serry (6): будьте готовы к повторному приносу тела недовольным клиентом
Это-то стопудово. Весь вопрос — когда (после какого пробега). Ставлю месяца на три максимум. Если дадите гарантию на этот или больший срок — секас будет повторным))

Scuzzy (7): секас будет повторным — не просто повторным, а более жёстким, так сказать.

Источник

Error b0605 hp 2055

‎06-09-2011 07:13 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

My HP Laserjet 2055DN displays a firmware error message: B0605

The printer and computer are connected via a USB cable and are «seeing» each other, when the printer is switched off the computer recognizes this and makes the «device unplugged» sound.

I have downloaded the 2050 firmware update and put the printer in Bootcode mode

When I then run the «send firmware» the software seems to complete and the smiley graphic comes up but nothing happens. The printer does not acknowledge the update or change messages.

The error code continues to remain current so I cannot use the printer.

As this is my main business printer this is quite inconvenient.

Does anyone know how to fix this?

Yours sincerely
John Edmiston

‎05-24-2012 07:34 AM — edited ‎05-24-2012 07:37 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

I know this is an old post, but because it ranks so high in google and I feel I have a solution, I thought I would answer it.

I had a users with an HP P2055DN who’s printer displayed the error B0605 message. I followed HP’s directions at http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c01687323&lang=en&cc=us&conte.

and put the printer in BootCode mode then ran the firmware updater.

The directions indicated that the printer would restart on it’s own, but it did not do that for me (and I feel many other people on the Internet according to what I could pull up on Google).

What I did was let the printer sit for about a minute after the Firmware Updater said it was done, then powered down the printer and pulled out it’s power cord. I let it sit for about 15 seconds, then plugged it back in and started it up. When the printer started up, the printer’s display went through a bunch of messages (Erasing. ) for a few seconds. When it got done with all of the messages, I was able to print to the printer again.

Источник

Error b0605 hp 2055

‎12-05-2013 06:52 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

hp laserjet 2055dn Error B0605, i need solutions for this error i tried with site but it not working.

‎12-05-2013 11:11 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Please refer to this document to help resolve you issue on the error message with this printer.

I am an HP employee.

Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

‎12-05-2013 11:11 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Please refer to this document to help resolve you issue on the error message with this printer.

I am an HP employee.

Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

‎12-06-2013 10:49 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

whatever u told us we did that but still it is not working,

when i strat the printer it immediately give b6050 error cade, n it is not at all communicating with the pc, please provide us solution this.

‎12-06-2013 10:55 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

‎12-07-2013 02:36 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

What were you trying to do when this error code happened? Installing a FW upgrade? If so, did you get the FW smiling face and a success! to tell you that you had completed the upgrade successfully?

If you have already sent the FW upgrade to the printer, try powering down the printer, pulling the power cord and letting it sit for about 15 secs. Plug everything back in and start the printer up. What happens? Do you see a new FW initialization (erasing) messaging? If so, let the printer do its job.

If not, try re-sending the printer FW upgrade again using the FW updater — once you have the complete update success message. What happens? Do you have the error message or did the printer initialize (erase), ect.) If not, power down, pull power cord, let sit. Plug everything back in and start up.

I am an HP employee.

Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

Источник

HP Printer Error B0605

B0605 Error Code HP Printer

You may see hp printer error b0605 error message popping up if the firmware of your printer gets crashed. Firmware gets crashed due to inappropriate behaviour, like: turning off the printer while the vital firmware update one is going on. This issue could be resolved by following the troubleshooting steps, like get the firmware re-flash in the BootCode mode and after that try rebooting your printer. Though firmware re-flash won’t help always, but yes, it is one of the best major you can take as a first step. If the HP Printer Error Message is displayed then your printer won’t be booted up in the ready state.

Causes B0605 Error Message HP Printer

Causes:

There might be two causes due to which this error is received:

  • You have installed the software driver of P2050 series printer on the PC previously
  • Software driver of P2050 series printer is not installed previously on the computer

Instruction

Case 1: Installation of driver was done previously on PC

  1. Ensure that printer is places in the bootcode mode
  • Keep holding the OK and Cancel buttons
  • Keep the power of the printer ON
  • Make sure that you are holding the buttons till the time Hewlett-Packard in first line and the Bootcode in second line is not displayed by the control panel
  1. Check carefully that your printer is connected to the PC through USB. After that run the firmware HP LJ P2055
  2. Now go to the dropdown list and after that click on the button of Send Firmware

Observe the panel of printer control carefully and make sure that on the control panel Downloading Update Data is flashing up along with the Programming App Flash. Wait, till the time upgrade utility gets finished. Your printer will be automatically restarted, and you will be able to see, Ready, displayed on control panel.

This means your firmware is recovered successfully.

Case 2: Installation of driver is not done previously

  1. Install the driver
  • Then get the printer installation CD inserted to it
  • After that go to the Start first and then to Settings and then to Printers and Faxes in Windows Operating System
  • In order to get the Add Printer Wizard started click on the Add a Printer, and then click on the Next button
  • Then check the local printer that is attached with the computer system. After that make sure that you remove the checkmark from Install my Plug and Play printer and Automatically detect box and then hit the Next button
  • Then go to the port of Use the following and select the FILE and tap on the Next button
  • After that, click on the button of Have Disk
  • Go to the CD Drive and browse it, where the printer installation CD was previously inserted. Click on the OK button
  • Click on the next button by highlighting the HP Laser Jet present in installation CD of printer. After that tap the Next button
  • By specifying the name of the Printer, hit the Next button
  • When, DO you want to print a test page? pop up, click on NO and then tap on Next
  • Click on the button saying Finish, and let the driver install
  • You will see that Verify printer is present in the window of Printer and Faxes
  1. Placing the P2055 in the bootcode mode
  • Keep holding the OK and Cancel buttons
  • Turn on the power of the printer
  • Keep on holding the buttons, until you see the display of the control panel flashing Hewlett-Packard in top line and Bootcode displaying on second line. Your printer is now in the mode of bootcode
  1. Go to the window of Printer and Faxes and on the icon of the HP LaserJet P2050 Series PCL6, do right click and choose the Properties
  2. Then by clicking on the tab of Ports you can see USB ports
  3. After that get the Property window closed
  4. Then ensure that USB cable is plugin from PC
  5. You will see the Found New Hardware Wizard popping up and enumeration of USB will start taking place
  6. Then open the Printer Properties again and choose the tab of Ports again
  7. Then tick mark the correct port in ports tab
  8. Click on Cancel if the window of Found New Hardware Wizard pop ups.
  9. Run the Firmware Update Utility
  10. Now from the drop down choose the printer and then tap on the button of Send Firmware
  11. Keep a close eye on the control panel and make sure that control panel is flashing the Downloading Update Data along with the Programming App Flash. Wait till the time upgrade utility gets finished. Automatically the printer will be restarted and you will be able to see, Ready, flashing on the display of control panel. The firmware is recovered successfully
  12. Close the New Found Hardware Wizard

Troubleshooting Steps HP Printer Error B0605

Troubleshooting the Printer Error B0605:

Step 1: Get the Firewall upgraded of the Printer

  • First of all, get the correct firmware downloaded
  • Then reload the upgraded and basic firmware
  • Pull the power cord and turn off the power of the printer and let it remain same for few seconds
  • Plug in back and get the printer started up
  • Check whether the error is removed or not. In case it is not, then try the next step

Step 2: Reinstalling the toner by removing it first

  • Disconnect and turnoff the printer’s power source
  • After that remove the toner mesh and paper tray as well
  • Turn on the power of the unit for at least 50 to 60 seconds and then turn the power off again
  • Get the paper tray and toner mesh installed again
  • Turn on the power of the unit and make sure that the power is up of the unit before getting the test page printed

Step 3: Reflashing firmware

  • Enter the boot mode and make sure that firmware is reflashed, also reboot the printer
  • This reflashing will help you to get rid of the error

Scope of Services

  • Advanced Printer Tech Support through experienced professionals
  • Immediate resolution of all the technical issues
  • Tech savvy and self-motivated staff
  • Capable of providing the customized solutions Dial Now

Источник

If you have an HP printer wherein you are encountering the B0605 error, then you must know how to fix the issue. Mostly HP printers work efficiently and are brilliant devices that are used both in offices and homes. However, just like any machine, it tends to show errors. If you are facing a B0605 error printer, then either you can troubleshoot the same by yourself, or you can reach on the Customer Care number to talk with the experts. If you are planning to troubleshoot the problem, then this blog is meant for you.

Reason for the error-

The specific reason due to which the error flashes is because the firmware gets crashed or because of the incapability of the booting process in the ready state. Below is enlisted the method that will help in solving the issue. It is important that the troubleshoot is done carefully. Mentioned under two  method. One is when the printer software driver is already on the PC and another when it is not found on the PC. You can select the type as per your requirement.

Placing printer in boot mode-

Type 1-

This method works when the printer software driver is already installed on the PC. Steps to be undertaken under this type are-

  1. a) Placing printer in boot code mode- In this step, the printer is placed in the boot code mode. For this, the cancel and ok buttons are held down. For activating this mode, these buttons have to be held while the printer is switched on.
  2. b) Ensure connectivity- One needs to ensure that the printer is connected to PC along USB.
  3. c) Option selection- This is the last step of the method where the HP printer is selected from the drop-down list and send firmware button is clicked.

Type 2-

In this type, the printer software driver is not found on the PC. The steps under this type are-

  1. a) Push in the CD of printer installation
  2. b) Move to start, select settings and from options click Printers and faxes
  3. c) Select options to add a printer and then select next
  4. d) Check for any local printer connected to your computer, disallow automatic detection option and install the plug and play printer. Select the next button after following all steps.
  5. e) Choose file and select have disk button
  6. f) Browse to find the CD drive in which printer installation CD is inserted, click okay when found.
  7. g) Select printer installation CD and move to the next button.
  8. h) Specify the name of the printer, move to next
  9. i) Click no followed with next selecting finish button at last.
  10. j) Once done verify if the printer is listed in printer and Faxes window.
  11. k) On printer and faxes window, click properties that appear as you right click on the printer.
  12. l) Select ports tab and see USB sort
  13. m) Close new hardware found wizard as it appears.

If you find yourself unable to solve the issue by following either of the two solutions, it is recommended that an expert’s help is taken. But we are positive this should answer your query on How to Fix HP Printer Error b0605

Модератор: vetal

Прилепить пост

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑HP LJ P2055dn Ошибка B0605, плате форматтера нужно новое встроенное программное обеспечение, но порт USB поврежден. Уведомление от технической поддержки HP не поможет мне. Я судимое ожог чип, но та же проблема.

error B0605 , formatter board need new firmware but USB port is broken. Notice from HP support not help me. I tryed burn chip on formatter board ,but same problem?

Аватар пользователя

3cxmoskva

Собрал картридж правильно

  • Не в сети

Прилепить пост

Сообщение Dani » Вт янв 17, 2017 9:10 am

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑Эта статья Вам не помогла?

This article didn’t help you?

Всё как то так ну или типа того

Аватар пользователя

Dani

Понюхал тонер

  • Не в сети
  • ip4500 ошибка 6А00 «AP position error»

    vodkin в форуме Принтеры струйные

    3
    4482

    vodkin
    Перейти к последнему сообщению
    Пн мар 19, 2012 5:22 am
  • Samsung CLX-3175 во время запуска пишет «Image error Resset»

    mr_sasha в форуме Принтеры, МФУ, факсы, копиры формата A4

    9
    5295

    maisterko
    Перейти к последнему сообщению
    Пн дек 14, 2015 4:19 pm
  • Установка Fuser Unit (печки) в Kyocera 5500i при error C6040

    Engine в форуме Принтеры, МФУ, копиры формата A3

    0
    2458

    Engine
    Перейти к последнему сообщению
    Вт фев 05, 2019 11:14 am
  • Epson L800 0x50 cr home position seeking error

    glam1112 в форуме Принтеры струйные

    2
    3640

    3cxmoskva
    Перейти к последнему сообщению
    Пн мар 12, 2018 3:28 pm
  • Samsung scx-4200 с компа печатает код ошибки Internal error

    Sveterkom в форуме Принтеры, МФУ, факсы, копиры формата A4

    4
    3242

    miha0707
    Перейти к последнему сообщению
    Чт дек 13, 2018 10:51 pm

Вернуться в Принтеры, МФУ, факсы, копиры формата A4

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 53

You may see hp printer error b0605 error message popping up if the firmware of your printer gets crashed. Firmware gets crashed due to inappropriate behaviour, like: turning off the printer while the vital firmware update one is going on. This issue could be resolved by following the troubleshooting steps, like get the firmware re-flash in the BootCode mode and after that try rebooting your printer. Though firmware re-flash won’t help always, but yes, it is one of the best major you can take as a first step. If the HP Printer Error Message is displayed then your printer won’t be booted up in the ready state.

HP Printer Error B0605

Causes B0605 Error Message HP Printer

Causes:

There might be two causes due to which this error is received:

  • You have installed the software driver of P2050 series printer on the PC previously
  • Software driver of P2050 series printer is not installed previously on the computer

Instruction

Case 1: Installation of driver was done previously on PC

  1. Ensure that printer is places in the bootcode mode
  • Keep holding the OK and Cancel buttons
  • Keep the power of the printer ON
  • Make sure that you are holding the buttons till the time Hewlett-Packard in first line and the Bootcode in second line is not displayed by the control panel
  1. Check carefully that your printer is connected to the PC through USB. After that run the firmware HP LJ P2055
  2. Now go to the dropdown list and after that click on the button of Send Firmware

Observe the panel of printer control carefully and make sure that on the control panel Downloading Update Data is flashing up along with the Programming App Flash. Wait, till the time upgrade utility gets finished. Your printer will be automatically restarted, and you will be able to see, Ready, displayed on control panel.

This means your firmware is recovered successfully.

Case 2: Installation of driver is not done previously

  1. Install the driver
  • Then get the printer installation CD inserted to it
  • After that go to the Start first and then to Settings and then to Printers and Faxes in Windows Operating System
  • In order to get the Add Printer Wizard started click on the Add a Printer, and then click on the Next button
  • Then check the local printer that is attached with the computer system. After that make sure that you remove the checkmark from Install my Plug and Play printer and Automatically detect box and then hit the Next button
  • Then go to the port of Use the following and select the FILE and tap on the Next button
  • After that, click on the button of Have Disk
  • Go to the CD Drive and browse it, where the printer installation CD was previously inserted. Click on the OK button
  • Click on the next button by highlighting the HP Laser Jet present in installation CD of printer. After that tap the Next button
  • By specifying the name of the Printer, hit the Next button
  • When, DO you want to print a test page? pop up, click on NO and then tap on Next
  • Click on the button saying Finish, and let the driver install
  • You will see that Verify printer is present in the window of Printer and Faxes
  1. Placing the P2055 in the bootcode mode
  • Keep holding the OK and Cancel buttons
  • Turn on the power of the printer
  • Keep on holding the buttons, until you see the display of the control panel flashing Hewlett-Packard in top line and Bootcode displaying on second line. Your printer is now in the mode of bootcode
  1. Go to the window of Printer and Faxes and on the icon of the HP LaserJet P2050 Series PCL6, do right click and choose the Properties
  2. Then by clicking on the tab of Ports you can see USB ports
  3. After that get the Property window closed
  4. Then ensure that USB cable is plugin from PC
  5. You will see the Found New Hardware Wizard popping up and enumeration of USB will start taking place
  6. Then open the Printer Properties again and choose the tab of Ports again
  7. Then tick mark the correct port in ports tab
  8. Click on Cancel if the window of Found New Hardware Wizard pop ups.
  9. Run the Firmware Update Utility
  10. Now from the drop down choose the printer and then tap on the button of Send Firmware
  11. Keep a close eye on the control panel and make sure that control panel is flashing the Downloading Update Data along with the Programming App Flash. Wait till the time upgrade utility gets finished. Automatically the printer will be restarted and you will be able to see, Ready, flashing on the display of control panel. The firmware is recovered successfully
  12. Close the New Found Hardware Wizard

Troubleshooting Steps HP Printer Error B0605

Troubleshooting the Printer Error B0605:

Step 1: Get the Firewall upgraded of the Printer

  • First of all, get the correct firmware downloaded
  • Then reload the upgraded and basic firmware
  • Pull the power cord and turn off the power of the printer and let it remain same for few seconds
  • Plug in back and get the printer started up
  • Check whether the error is removed or not. In case it is not, then try the next step

Step 2: Reinstalling the toner by removing it first

  • Disconnect and turnoff the printer’s power source
  • After that remove the toner mesh and paper tray as well
  • Turn on the power of the unit for at least 50 to 60 seconds and then turn the power off again
  • Get the paper tray and toner mesh installed again
  • Turn on the power of the unit and make sure that the power is up of the unit before getting the test page printed

Step 3: Reflashing firmware

  • Enter the boot mode and make sure that firmware is reflashed, also reboot the printer
  • This reflashing will help you to get rid of the error

Scope of Services

  • Advanced Printer Tech Support through experienced professionals
  • Immediate resolution of all the technical issues
  • Tech savvy and self-motivated staff
  • Capable of providing the customized solutions Dial Now Technical Support For Printer

May 30, 2018November 28, 2019

Перейти к контенту

Issue Description:

Print cannot boot up into ready state with an error message shown on printer control panel. The error messages include ERROR: B0601/ B0602/ B0603/ B0604/ B0605.

Root Cause:

Firmware crashes.
Note: Inappropriate behavior may cause firmware crash. For example, a printer is turned off when critical firmware update is undergoing.

Solution:

Firmware Update Utility.

note:

This utility can be obtained at hp.com.

There are two use cases when encountering the issue:

  1. P2050 series printer software driver is previously installed on the PC.

    note:

    The instruction have 3 steps and easy to follow as quick fix.

  2. P2050 series printer software driver is NOT previously installed on the PC, such as Dead on Arrival unit.

    note:

    The instruction is only for advanced PC users only as it’s very complicated with 14 steps. Please evaluate the customer knowledge level before helping a customer to do so. Otherwise, replacing formatter is the alternatives.

Instructions for Use case 1: driver is previously installed on PC

  1. Place printer in bootcode mode.

    1. Hold down the Cancel and OK buttons.

    2. Power on printer.

    3. Continue to hold down buttons until control panel dislpays Hewlett-
      Packard on the first line and Bootcode on the second line.

      note:

      Printer is now in bootcode mode
      2.

  2. Ensure printer is connected via USB to PC. Run HP LJ P2055 Firmware
    Update Utility.

    note:

    This utility can be obtained at hp.com.

  3. Select the HP LaserJet P2050 series printer from the dropdown list and click
    Send Firmware button.

    Please observe the printer control panel and verify Downloading Update Data is displayed on control panel followed by Programming App Flash; please wait for
    upgrade utility to finish. Printer would be restarted automatically and the control
    panel display would show Ready.

Then the firmware is now successfully recovered.

Instructions for use case 2: driver is NOT previously installed

  1. Install the driver for HP LaserJet P2050 series printer:

    1. Insert printer installation CD.

    2. In Windows OS, please go to Start, Settings, Printers and Faxes.

    3. Click Add a printer to start Add Printer Wizard as shown blow and
      click on Next button.

    4. Check Local printer attached to this computer box; uncheck
      Automatically detect and Install my Plug and Play printer box and click on
      Next button.

    5. Select FILE:(Print to File) in the Use the following port: dropdown list
      and click on Next button.

    6. Click Have Disk… button.

    7. Browse to the CD drive in which the printer installation CD is inserted
      previously and click OK button.

    8. Highlight the HP LaserJet P2050 Series PCL 6 found in the
      printer installation CD and click on Next button.

    9. Specify the Printer name and click on Next button.

    10. Select No for Do you want to print a test page? and click on Next.

    11. Click the Finish button and allow driver to install as shown below.

    12. Verify printer is listed in Printer and Faxes window as shown below:

  2. Place P2055 in boot code mode:

    1. Hold down the Cancel and OK buttons.

    2. Power on printer.

    3. Continue to hold down buttons until control panel dislpays Hewlett-Packard on the first line and Bootcode on the second line
      Printer is now in bootcode mode.

  3. In the Printer and Faxes window, right click on the HP LaserJet
    P2050 Series PCL6 icon and select Properties.

  4. Click the Ports tab and view the USB ports as shown below.

    note:

    If more than one (USB001) please take note of all listed ports, as other
    installed printers may have USB ports (USB002, USB003, etc).

  5. Close Properties window.

  6. Plug in USB cable from to PC

  7. The Found New Hardware Wizard will pop up, and tje printer USB enumeration will
    happen.

  8. Open printer properties and select Ports tab again.

  9. In ports tab, tick the correct port that the HP LaserJet P2050 series printer is
    enumerated on and click OK.

  10. Click Cancel on Found New Hardware wizard window.

    note:

    Not the driver is installed and it is pointed to correct USB port.

  11. Run HP LJ P2055 Firmware Update Utility.

    note:

    This utility can be obtained
    at hp.com.

  12. Select printer from the dropdown list and click Send Firmware button.

    Please observe the printer control panel and verify Downloading Update Data is
    displayed on control panel followed by Programming App Flash; please wait for
    upgrade utility to finish. Printer would be restarted automatically and the control
    panel display would show Ready. Then the firmware is now successfully
    recovered.

  13. Close New Hardware Found Wizard.

  14. Delete all instances of P2055 printer in Printers and Faxes and run normal
    CD install to install HP LaserJet P2050 series printer drivers properly from printer
    installation CD.

Модератор: vetal

Прилепить пост

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑HP LJ P2055dn Ошибка B0605, плате форматтера нужно новое встроенное программное обеспечение, но порт USB поврежден. Уведомление от технической поддержки HP не поможет мне. Я судимое ожог чип, но та же проблема.

error B0605 , formatter board need new firmware but USB port is broken. Notice from HP support not help me. I tryed burn chip on formatter board ,but same problem?

Аватар пользователя

3cxmoskva

Собрал картридж правильно

  • Не в сети

Прилепить пост

Сообщение Dani » Вт янв 17, 2017 9:10 am

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑Эта статья Вам не помогла?

This article didn’t help you?

Всё как то так ну или типа того

Аватар пользователя

Dani

Понюхал тонер

  • Не в сети
  • ip4500 ошибка 6А00 «AP position error»

    vodkin в форуме Принтеры струйные

    3
    4454

    vodkin
    Перейти к последнему сообщению
    Пн мар 19, 2012 5:22 am
  • Samsung CLX-3175 во время запуска пишет «Image error Resset»

    mr_sasha в форуме Принтеры, МФУ, факсы, копиры формата A4

    9
    5254

    maisterko
    Перейти к последнему сообщению
    Пн дек 14, 2015 4:19 pm
  • Установка Fuser Unit (печки) в Kyocera 5500i при error C6040

    Engine в форуме Принтеры, МФУ, копиры формата A3

    0
    2448

    Engine
    Перейти к последнему сообщению
    Вт фев 05, 2019 11:14 am
  • Brother HL-2030R — Hight Voltage Error (Drum+Toner)

    lev91 в форуме Принтеры, МФУ, факсы, копиры формата A4

    11
    9872

    kvg
    Перейти к последнему сообщению
    Вс авг 26, 2012 3:32 pm
  • Epson L800 0x50 cr home position seeking error

    glam1112 в форуме Принтеры струйные

    2
    3601

    3cxmoskva
    Перейти к последнему сообщению
    Пн мар 12, 2018 3:28 pm

Вернуться в Принтеры, МФУ, факсы, копиры формата A4

Кто сейчас на форуме

Сейчас этот форум просматривают: darknebola и гости: 123

You may see hp printer error b0605 error message popping up if the firmware of your printer gets crashed. Firmware gets crashed due to inappropriate behaviour, like: turning off the printer while the vital firmware update one is going on. This issue could be resolved by following the troubleshooting steps, like get the firmware re-flash in the BootCode mode and after that try rebooting your printer. Though firmware re-flash won’t help always, but yes, it is one of the best major you can take as a first step. If the HP Printer Error Message is displayed then your printer won’t be booted up in the ready state.

HP Printer Error B0605

Causes B0605 Error Message HP Printer

Causes:

There might be two causes due to which this error is received:

  • You have installed the software driver of P2050 series printer on the PC previously
  • Software driver of P2050 series printer is not installed previously on the computer

Instruction

Case 1: Installation of driver was done previously on PC

  1. Ensure that printer is places in the bootcode mode
  • Keep holding the OK and Cancel buttons
  • Keep the power of the printer ON
  • Make sure that you are holding the buttons till the time Hewlett-Packard in first line and the Bootcode in second line is not displayed by the control panel
  1. Check carefully that your printer is connected to the PC through USB. After that run the firmware HP LJ P2055
  2. Now go to the dropdown list and after that click on the button of Send Firmware

Observe the panel of printer control carefully and make sure that on the control panel Downloading Update Data is flashing up along with the Programming App Flash. Wait, till the time upgrade utility gets finished. Your printer will be automatically restarted, and you will be able to see, Ready, displayed on control panel.

This means your firmware is recovered successfully.

Case 2: Installation of driver is not done previously

  1. Install the driver
  • Then get the printer installation CD inserted to it
  • After that go to the Start first and then to Settings and then to Printers and Faxes in Windows Operating System
  • In order to get the Add Printer Wizard started click on the Add a Printer, and then click on the Next button
  • Then check the local printer that is attached with the computer system. After that make sure that you remove the checkmark from Install my Plug and Play printer and Automatically detect box and then hit the Next button
  • Then go to the port of Use the following and select the FILE and tap on the Next button
  • After that, click on the button of Have Disk
  • Go to the CD Drive and browse it, where the printer installation CD was previously inserted. Click on the OK button
  • Click on the next button by highlighting the HP Laser Jet present in installation CD of printer. After that tap the Next button
  • By specifying the name of the Printer, hit the Next button
  • When, DO you want to print a test page? pop up, click on NO and then tap on Next
  • Click on the button saying Finish, and let the driver install
  • You will see that Verify printer is present in the window of Printer and Faxes
  1. Placing the P2055 in the bootcode mode
  • Keep holding the OK and Cancel buttons
  • Turn on the power of the printer
  • Keep on holding the buttons, until you see the display of the control panel flashing Hewlett-Packard in top line and Bootcode displaying on second line. Your printer is now in the mode of bootcode
  1. Go to the window of Printer and Faxes and on the icon of the HP LaserJet P2050 Series PCL6, do right click and choose the Properties
  2. Then by clicking on the tab of Ports you can see USB ports
  3. After that get the Property window closed
  4. Then ensure that USB cable is plugin from PC
  5. You will see the Found New Hardware Wizard popping up and enumeration of USB will start taking place
  6. Then open the Printer Properties again and choose the tab of Ports again
  7. Then tick mark the correct port in ports tab
  8. Click on Cancel if the window of Found New Hardware Wizard pop ups.
  9. Run the Firmware Update Utility
  10. Now from the drop down choose the printer and then tap on the button of Send Firmware
  11. Keep a close eye on the control panel and make sure that control panel is flashing the Downloading Update Data along with the Programming App Flash. Wait till the time upgrade utility gets finished. Automatically the printer will be restarted and you will be able to see, Ready, flashing on the display of control panel. The firmware is recovered successfully
  12. Close the New Found Hardware Wizard

Troubleshooting Steps HP Printer Error B0605

Troubleshooting the Printer Error B0605:

Step 1: Get the Firewall upgraded of the Printer

  • First of all, get the correct firmware downloaded
  • Then reload the upgraded and basic firmware
  • Pull the power cord and turn off the power of the printer and let it remain same for few seconds
  • Plug in back and get the printer started up
  • Check whether the error is removed or not. In case it is not, then try the next step

Step 2: Reinstalling the toner by removing it first

  • Disconnect and turnoff the printer’s power source
  • After that remove the toner mesh and paper tray as well
  • Turn on the power of the unit for at least 50 to 60 seconds and then turn the power off again
  • Get the paper tray and toner mesh installed again
  • Turn on the power of the unit and make sure that the power is up of the unit before getting the test page printed

Step 3: Reflashing firmware

  • Enter the boot mode and make sure that firmware is reflashed, also reboot the printer
  • This reflashing will help you to get rid of the error

Scope of Services

  • Advanced Printer Tech Support through experienced professionals
  • Immediate resolution of all the technical issues
  • Tech savvy and self-motivated staff
  • Capable of providing the customized solutions Dial Now Technical Support For Printer

May 30, 2018November 28, 2019

If you have an HP printer wherein you are encountering the B0605 error, then you must know how to fix the issue. Mostly HP printers work efficiently and are brilliant devices that are used both in offices and homes. However, just like any machine, it tends to show errors. If you are facing a B0605 error printer, then either you can troubleshoot the same by yourself, or you can reach on the Customer Care number to talk with the experts. If you are planning to troubleshoot the problem, then this blog is meant for you.

Reason for the error-

The specific reason due to which the error flashes is because the firmware gets crashed or because of the incapability of the booting process in the ready state. Below is enlisted the method that will help in solving the issue. It is important that the troubleshoot is done carefully. Mentioned under two  method. One is when the printer software driver is already on the PC and another when it is not found on the PC. You can select the type as per your requirement.

Placing printer in boot mode-

Type 1-

This method works when the printer software driver is already installed on the PC. Steps to be undertaken under this type are-

  1. a) Placing printer in boot code mode- In this step, the printer is placed in the boot code mode. For this, the cancel and ok buttons are held down. For activating this mode, these buttons have to be held while the printer is switched on.
  2. b) Ensure connectivity- One needs to ensure that the printer is connected to PC along USB.
  3. c) Option selection- This is the last step of the method where the HP printer is selected from the drop-down list and send firmware button is clicked.

Type 2-

In this type, the printer software driver is not found on the PC. The steps under this type are-

  1. a) Push in the CD of printer installation
  2. b) Move to start, select settings and from options click Printers and faxes
  3. c) Select options to add a printer and then select next
  4. d) Check for any local printer connected to your computer, disallow automatic detection option and install the plug and play printer. Select the next button after following all steps.
  5. e) Choose file and select have disk button
  6. f) Browse to find the CD drive in which printer installation CD is inserted, click okay when found.
  7. g) Select printer installation CD and move to the next button.
  8. h) Specify the name of the printer, move to next
  9. i) Click no followed with next selecting finish button at last.
  10. j) Once done verify if the printer is listed in printer and Faxes window.
  11. k) On printer and faxes window, click properties that appear as you right click on the printer.
  12. l) Select ports tab and see USB sort
  13. m) Close new hardware found wizard as it appears.

If you find yourself unable to solve the issue by following either of the two solutions, it is recommended that an expert’s help is taken. But we are positive this should answer your query on How to Fix HP Printer Error b0605

Источник

Понравилась статья? Поделить с друзьями:
  • Ошибка b0402 субару форестер
  • Ошибка autocad нераспознанная версия не может быть прочитано
  • Ошибка autocad application
  • Ошибка autocad 0x0000
  • Ошибка auto hold туарег