| 1001 System error %1 |
| 1002 System error %1 |
| 1003 Alarm pointer for this self-clearing alarm %1 is zero |
| 1004 Alarm reaction to NCK alarm incorrectly configured |
| 1005 Operating system error %1 parameter %2 %3 %4 |
| 1010 Channel %1 system error %2 action %3 |
| 1011 Channel %1 %3 %4 system error %2 |
| 1012 Channel %1 system error %2 %3 %4 |
| 1013 Channel %1 system error %2 |
| 1014 Channel %1 system error %2 |
| 1015 Channel %1 axis %2 system error %3 |
| 1016 Channel %1 axis %2 system error %3 |
| 1017 Channel %1 axis %2 system error %3 |
| 1018 Floating point arithmetic error in channel %1 task %2 station %3 FPU state %4 %4 |
| 1019 Floating point arithmetic error at address %3 in channel %1 task %2 FPU state %4 |
| 1030 System error in link module error code %1 error type %2 |
| 1031 Link module generated an unspecified error %1 NCU %2 %3 %4 |
| 1100 No valid firmware |
| 1160 Assertion failed in %1: %2 |
| 2000 PLC sign-of-life monitoring |
| 2001 PLC has not started up |
| 2100 NCK battery warning threshold reached |
| 2101 NCK battery alarm |
| 2102 NCK battery alarm |
| 2110 NCK temperature alarm |
| 2120 NCK fan alarm |
| 2130 5V/24V encoder or 15V D/A converter under voltage |
| 2140 The actual service switch position forces a SRAM to be cleared at the next Power On (general reset active) |
| 2190 Hardware plug-in module for communication with the digitizer missing |
| 2192 No NCU link module exists, MD %1 reset |
| 2193 Safety Integrated is not available for link axis %1. |
| 2195 Channel %1 axis %2 high-speed punching/nibbling not possible via link |
| 2196 Link axis active and $MN_MM_SERVO_FIFO_SIZE != %1 |
| 2900 Reboot is delayed |
| 3000 Emergency stop |
| 3001 Internal emergency stop |
| 4000 Channel %1 machine data %2[%3] has gap in axis assignment |
| 4001 Channel %1 axis %2 defined for more than one channel via machine data %3 |
| 4002 Channel %1 machine data %2[%3] assigns an axis not defined in channel |
| 4003 Axis %1 incorrect assignment of master channel in machine data %2 |
| 4004 Channel %1 machine data %2 axis %3 defined repeatedly as geometry axis |
| 4005 Maximum number of axes in channel %1 exceeded. Limit %2 |
| 4007 Axis %1 incorrect assignment of master NCU in machine data %2 |
| 4010 Invalid identifier used in machine data %1[%2] |
| 4011 Channel %1 invalid identifier used in machine data %2[%3] |
| 4012 Invalid identifier used in machine data %1[%2] |
| 4013 Invalid NCU link configuration by machine data %1 = %2 , on NCU_1 = %3 |
| 4014 Axis %1 defined several times in %2 |
| 4016 Axis %1 already used by NCU %2 |
| 4017 Axis container %1, location %2 already used by NCU %3 |
| 4018 Axis container %1, location %2 not used by any channel |
| 4019 Axis container %1 advance not allowed with current status of NCU %2 |
| 4020 Identifier %1 used several times in machine data %2 |
| 4021 Channel %1 identifier %2 used several times in machine data %3 |
| 4022 Axis container %3 switch not allowed: ext. zero offset active channel %1 axis %2 |
| 4023 Axis container %1 switch not allowed, axis container %2 switch active |
| 4024 Invalid axis configuration due to missing axis container machine data |
| 4025 Axis container %3 switch not allowed: master/slave active channel %1 axis %2 |
| 4026 Machine data %1[%2], link axis NC%3_AX%4 not used by any channel |
| 4027 Notice: MD %1 was also changed for the other axes of axis container %2 |
| 4028 Notice! The axial MDs of the axes of the axis containers were matched. |
| 4029 Notice: the axial MDs in axis container %1 will be matched on the next power-up |
| 4030 Channel %1 axis identifier missing in machine data %2[%3] |
| 4031 Channel %1 link axis %2 defined for more than one channel in machine data %3 |
| 4032 Channel %1 wrong identifier for facing axis in %2 |
| 4033 Notice: NCU link communication still not connected |
| 4034 Local link axis %1 is not allowed for different interpolation cycle time = %2/%3 |
| 4035 Interpolation cycle from NCU%1 = %2 does not match NCU%3 = %4 |
| 4036 Wrong NCU link configuration by MD %1 |
| 4040 Channel %1 axis identifier %2 not consistent with machine data %3 |
| 4045 Channel %1 conflict between machine data %2 and machine data %3 |
| 4050 NC code identifier %1 cannot be reconfigured to %2 |
| 4060 Standard machine data loaded |
| 4062 Backup data loaded |
| 4065 Buffered memory was restored from backup medium (potential loss of data!) |
| 4066 Buffered memory of FFS restored from backup medium (potential loss of data!) |
| 4070 Normalizing machine data has been altered |
| 4073 Compile cycle functions define machine data number %1 several times |
| 4075 Machine data %1 (and maybe others) not altered due to missing permission level %2 |
| 4076 %1 Machine data could not be altered with permission level %2 |
| 4077 New value %1 of MD %2 not set. Requested %3 bytes too much %4 memory. |
| 4080 Incorrect configuration of indexing axis in MD %1 |
| 4090 Too many errors during power-up |
| 4100 System cycle time/scan time divider corrected for digital drive |
| 4102 Default values for drive cycle times differ |
| 4110 IPO factor increased to %1 |
| 4111 PLC cycle increased to %1 ms |
| 4112 Servo cycle changed to %1 ms |
| 4113 Sysclock cycle changed to %1 ms |
| 4114 Error in DP cycle of SDB1000 |
| 4115 Time ratio communication to Ipo changed to %1 |
| 4150 Channel %1 invalid M function sub program call configured |
| 4152 Illegal configuration of the Block display with absolute values function |
| 4160 Channel %1 invalid M function number configured for spindle switchover |
| 4170 Invalid M function number for channel synchronisation assigned |
| 4180 Invalid M function number assigned to enable ASUP |
| 4181 Channel %1 invalid assignment of an M auxiliary function number |
| 4182 Channel %1 invalid M auxiliary function number in %2%3, MD reset |
| 4183 Channel %1 M auxiliary function number %2 used several times (%3 and %4) |
| 4184 Channel %1 illegally predefined auxiliary function in %2%3, MD reset |
| 4185 Channel %1 illegal auxiliary function configured %2 %3 %4 |
| 4200 Channel %1 geometry axis %2 must not be declared a rotary axis |
| 4210 Channel %1 spindle %2 declaration as rotary axis missing |
| 4215 Channel %1 spindle %2 declaration as modulo axis missing |
| 4220 Channel %1 spindle %2 declared repeatedly |
| 4225 Channel %1 axis %2 declaration as rotary axis missing |
| 4230 Channel %1 data alteration from external not possible in current channel state |
| 4240 Runtime overflow for IPO cycle or position controller cycle, IP %1 |
| 4250 FastPlcCom functionality not available |
| 4252 PLCIO read error: %1 |
| 4254 PLCIO write error: %1 |
| 4260 Machine data %1 illegal |
| 4270 Machine data %1 assigns not activated NCK input/output byte %2 |
| 4275 Machine data %1 and %2 both assign the same NCK output byte no. %3 several times |
| 4280 Assignment of NCK input/output byte via MD %1[%2] does not match hardware configuration |
| 4282 Hardware of external NCK outputs assigned repeatedly |
| 4285 Error on terminal block %1, error code %2 |
| 4290 Local P-bus sign-of-life monitoring |
| 4291 Module in local P-bus slot %1 error codes %2 %3 %4 %2 %3 %4 |
| 4300 Declaration in MD %1 is not allowed for geometry axis/spindle %2. |
| 4310 Declaration in MD %1 index %2 is not allowed. |
| 4320 Axis %1 function %2 %3 and %4 not allowed |
| 4334 Channel %1 The amount of fine correction in parameter %2 of the orientable toolholder %3 is too large |
| 4336 Channel %1 orientable toolholder no. %2 for orientation transformation %3 does not exist |
| 4338 Channel %1 invalid transformation type %2 in toolholder %3 for orientation transformer %4 |
| 4340 Channel %1 block %2 invalid transformation type in transformation no. %3 |
| 4341 Channel %1 block %2 no data set available for transformation no. %3 |
| 4342 Channel %1 invalid machine data for general 5-axis transformation error no. %2 |
| 4343 Channel %1 attempt made to change the machine data of an active transformation. |
| 4345 Channel %1 invalid configuration in chained transformation no.%2 |
| 4346 Channel %1 invalid geoaxis assignment in machine data %2[%3] |
| 4347 Channel %1 invalid channel axis assignment in machine data %2[%3] |
| 4350 Channel %1 axis identifier %2 machine data %3 not consistent with machine data %4 |
| 4400 MD alteration will cause reorganisation of buffered memory (loss of data!) |
| 4502 Channel %1 anachronism %2(%3) -> %4 |
| 5000 Communication job not executable %1 |
| 6000 Memory reorganized using standard machine data |
| 6010 Channel %1 data block %2 not or not completely created, error code %3 |
| 6020 Machine data have been altered now memory is reorganized |
| 6030 Limit of user memory has been adapted |
| 6035 Instead of %1 KB the system has only %2 KB of free user memory of type %3 |
| 6100 Error while creating %1, error number %2 %3 |
| 6401 Channel %1 tool change not possible: Empty location for tool %2 Duplo no. %3 on magazine %4 not available. |
| 6402 Channel %1 tool change not possible. Magazine no. %2 not available |
| 6403 Channel %1 tool change not possible. Magazine location number %2 on magazine %3 not available. |
| 6404 Channel %1 tool change not possible. Tool %2 not available or not usable |
| 6405 Channel %1 command %2 has invalid PLC acknowledge parameter %3 identifier %4 |
| 6406 Channel %1 PLC acknowledge for command %2 is missing |
| 6407 Channel %1 tool %2 cannot be placed in magazine %3 on location %4.Invalid definition of magazine! |
| 6410 TO unit %1 tool %2 / Duplo no. %3 has reached its pre warning limit with D = %4 |
| 6411 Channel %1 tool %2 / Duplo no. %3 has reached its prewarning limit with D = %4 |
| 6412 TO unit %1 tool %2 / Duplo no. %3 has reached its monitoring limit with D = %4 |
| 6413 Channel %1 tool %2 / Duplo no. %3 has reached its monitoring limit with D = %4 |
| 6421 Channel %1 tool move not possible. Empty location for tool %2 Duplo no. %3 on magazine %4 not available. |
| 6422 Channel %1 tool move not possible. Magazine no. %2 not available. |
| 6423 Channel %1 tool move not possible. Location %2 on magazine %3 not available. |
| 6424 Channel %1 tool move not possible. Tool %2 not available/not usable. |
| 6425 Channel %1 tool %2 cannot be placed in magazine %3 on location %4. Invalid definition of magazine! |
| 6430 Workpiece counter: overflow in table of monitored cutting edges. |
| 6431 Function not allowed. Tool management/monitoring is not active. |
| 6432 Function not executable. No tool assigned to tool holder/spindle |
| 6433 Channel %1 block %2 %3 not available with tool management |
| 6434 Channel %1 block %2 NC command SETMTH not allowed because tool holder function not active |
| 6441 Writing of $P_USEKT not allowed. |
| 6442 Channel %1 function not executable. No tool assigned to desired magazine/magazine location %2. |
| 6450 Channel %1 tool change not possible. Invalid magazine location no. %2 in buffer magazine |
| 6451 Channel %1 tool change not possible. No buffer magazine defined. |
| 6452 Channel %1 tool change not possible. Tool holder/spindle number = %2 not defined. |
| 6453 Channel %1 tool change not possible. No assignment between toolholder/spindle no. = %2 and buffer magazine location %3 |
| 6454 Channel %1 tool change not possible. No distance relation available. |
| 6500 NC memory full |
| 6510 Too many part programs in the NC memory |
| 6520 The value of the machine data %1%2 is too low |
| 6530 Too many files in directory |
| 6540 Too many directories in the NC memory |
| 6550 Too many subdirectories |
| 6560 Data format not allowed |
| 6570 NC memory full |
| 6580 NC memory full |
| 6600 NC card memory is full |
| 6610 Too many files open on NC card |
| 6620 NC card has incorrect format |
| 6630 NC card hardware is defective |
| 6640 NC card is not inserted |
| 6650 Write protection of NC card is active |
| 6660 Flash File System option is not set |
| 6670 NC card read active |
| 6671 NC card write active |
| 6690 Cycles from NC card cannot be copied to the passive file system. |
| 6691 Cycles from the passive file system cannot be saved on the NC card |
| 6692 Cycle %1 lost |
| 6693 File %1 lost |
| 6698 Unknown NC card (%1/%2). Writing not possible. |
| 6700 Channel %1 value of the machine data %2%3 is too low |
| 7000 Too many compile cycle alarms defined |
| 7010 Range of MMC alarm numbers for compile cycles exceeded |
| 7020 Compile cycle alarm number has not been defined |
| 7100 Compile cycles VDI area: %1 byte for inputs and %2 byte for outputs. Maximum %3 bytes available. |
| 7200 Problem with externally linked compile cycle %1 %2 |
| 7201 Assertion error in %1 line %2 |
| 7202 Missing option bit for %1: %2 |
| 8000 Channel %1 option user interrupt programs not set |
| 8010 Option activation of more than %1 axes not set |
| 8020 Option activation of more than %1 channels not set |
| 8021 Option activation of more than %1 mode groups not set |
| 8022 Option activation of more than %1KB SRAM not set |
| 8030 Channel %1 block %2 option interpolation of more than 4 axes not set |
| 8032 Option activation of more than %1 link axes not set |
| 8034 Option activation of axis containers not set |
| 8036 Option: it is not allowed to set different IPO cycles or position control cycles with NCU link. |
| 8038 Option activation of more than %1 lead link axes not set |
| 8040 Machine data %1 reset, corresponding option is not set |
| 8041 Axis %1: MD %2 reset, corresponding option not sufficient |
| 8044 Option for IPO cycle time %1 ms not set |
| 8045 Option for selected cycle settings not set |
| 8080 %1 options are activated without setting the license key |
| 8081 %1 options are activated that are not licensed by the license key |
| 8082 The license key was entered three times, Power On required before next try. |
| 8098 Invalid combination of options (%1) |
| 8100 Channel %1 block %2: function not possible |
| 10203 Channel %1 NC start without reference point |
| 10207 Channel %1 error when selecting or deselecting the digitize function |
| 10208 Channel %1 continue program with NC start |
| 10209 Channel %1 internal NC stop after block search |
| 10222 Channel %1 inter-channel communication not possible |
| 10223 Channel %1: Command %2 is already occupied |
| 10225 Channel %1: command denied |
| 10299 Channel %1 Auto-Repos function is not enabled |
| 10600 Channel %1 block %2 auxiliary function during thread cutting active |
| 10601 Channel %1 block %2 zero velocity at block end point during thread cutting |
| 10604 Channel %1 block %2 thread lead increase too high |
| 10605 Channel %1 block %2 thread lead decrease too high |
| 10607 Channel %1 block %2 thread with frame not executable |
| 10610 Channel %1 axis %2 not stopped |
| 10620 Channel %1 block %3 axis %2 at software limit switch %4 |
| 10621 Channel %1 axis %2 rests on software limit switch %3 |
| 10630 Channel %1 block %2 axis %3 at working area limit %4 |
| 10631 Channel %1 axis %2 rests at working area limit %3 |
| 10650 Channel %1 axis %2 incorrect gantry machine data, error code %3 |
| 10651 Channel %1 illegal gantry configuration. Error code %2 |
| 10652 Channel %1 axis %2 gantry warning threshold exceeded |
| 10653 Channel %1 axis %2 gantry error threshold exceeded |
| 10654 Channel %1 waiting for synchronization start of gantry group %2 |
| 10655 Channel %1 synchronization of gantry group %2 in progress |
| 10656 Channel %1 axis %2 gantry alarm not yet used |
| 10700 Channel %1 block %2 NCK protection zone %3 violated during automatic or MDA mode |
| 10701 Channel %1 block %2 channel-specific protection zone %3 violated during automatic or MDA mode |
| 10702 Channel %1 NCK protection zone %2 violated during manual mode |
| 10703 Channel %1 channel-specific protection zone %2 violated during manual mode |
| 10704 Channel %1 block %2 protection zone monitoring is not guaranteed |
| 10706 Channel %1 NCK protection zone %2 reached with axis %3 during manual mode |
| 10707 Channel %1 channel-specific protection zone %2 reached with axis %3 during manual mode |
| 10710 Channel %1 block %2 conflict with centre less grinding |
| 10720 Channel %1 block %3 axis %2 software limit switch %4 |
| 10721 Channel %1 block %3 axis %2 software limit switch %4 |
| 10730 Channel %1 block %3 axis %2 working area limitation %4 |
| 10731 Channel %1 block %3 axis %2 working area limitation %4 |
| 10740 Channel %1 block %2 too many empty blocks in WAB programming |
| 10741 Channel %1 block %2 direction reversal with WAB infeed motion |
| 10742 Channel %1 block %2 WAB distance invalid or not programmed |
| 10743 Channel %1 block %2 WAB programmed several times |
| 10744 Channel %1 block %2 no valid WAB direction defined |
| 10745 Channel %1 block %2 WAB end position not clear |
| 10746 Channel %1 block %2 block search stop for WAB |
| 10747 Channel %1 block %2 retraction direction not defined for WAB |
| 10748 Channel %1 block %2 illegal retract plane with WAB |
| 10750 Channel %1 block %2 tool radius compensation activated without tool number |
| 10751 Channel %1 block %2 danger of collision due to tool radius compensation |
| 10752 Channel %1 block %2 overflow of local block buffer with tool radius compensation |
| 10753 Channel %1 block %2 selection of the tool radius compensation only possible in linear block |
| 10754 Channel %1 block %2 deselection of the tool radius compensation only possible in linear block |
| 10755 Channel %1 block %2 selection of the tool radius compensation via KONT not possible at the current starting point |
| 10756 Channel %1 block %2 deselection of the tool radius compensation via KONT not possible at the programmed end point |
| 10757 Channel %1 block %2 changing the compensation plane while tool radius compensation is active not possible |
| 10758 Channel %1 block %2 curvature radius with variable compensation value too small |
| 10759 Channel %1 block %2 path is parallel to tool orientation |
| 10760 Channel %1 block %2 helical axis is not parallel to tool orientation |
| 10761 Channel %1 block %2 tool radius compensation for ellipse with more than one revolution not possible |
| 10762 Channel %1 block %2 too many empty blocks between two traversing blocks with active tool radius compensation |
| 10763 Channel %1 block %2 path component of the block in the compensation plane becomes zero |
| 10764 Channel %1 block %2 discontinuous path with active tool radius compensation |
| 10765 Channel %1 block %2 3D tool radius compensation not possible |
| 10766 Channel %1 illegal change of surface orientation between block %2 and block %3 |
| 10767 Channel %1 block %2 processing with tilt angle unequal 0 not possible |
| 10768 Channel %1 block %2 illegal tool orientation with 3D tool radius compensation |
| 10769 Channel %1 block %2 Illegal surface normal vector with 3D tool radius compensation |
| 10770 Channel %1 block %2 change of corner type due to change of orientation with active tool radius compensation |
| 10771 Channel %1 block %2 overflow of local block buffer due to orientation smoothing |
| 10772 Channel %1 block %2 illegal orientation change when activating or deactivating 3D face cutting |
| 10773 Channel %1 illegal tool orientation in block %2 at inside corner with block %3 |
| 10774 Channel %1 illegal tool dimensions with face cutting in block %2 |
| 10775 Channel %1 illegal tool change with face cutting in block %2 |
| 10776 Channel %1 block%2 axis %3 must be geometry axis if tool radius compensation is active |
| 10777 Channel %1 block %2 tool radius compensation: too many blocks with suppression of compensation |
| 10778 Channel %1 block %2 preprocessing stop with active tool radius compensation |
| 10779 Channel %1 block %2 preprocessing stop with active tool radius compensation |
| 10780 Channel %1 block %2 preprocessing stop with active tool radius compensation |
| 10781 Channel %1 block %2 illegal orientation of involute with tool radius compensation |
| 10782 Channel %1 block %2 illegal curve type with tool radius compensation |
| 10783 Channel %1 block %2 tool radius compensation type requires orientation transformation |
| 10784 Channel %1 block %2 illegal tool for tool radius compensation with constraint surface |
| 10790 Channel %1 block %2 plane change during linear programming with angles |
| 10791 Channel %1 block %2 invalid angle during linear programming |
| 10792 Channel %1 block %2 illegal interpolation type during linear programming with angles |
| 10793 Channel %1 block %2 second block missing during linear programming with angles |
| 10794 Channel %1 block %2 angle specification missing in second block during linear interpolation with angles |
| 10795 Channel %1 block %2 end point specification during angle programming contradictory |
| 10800 Channel %1 block %3 axis %2 is not a geometry axis |
| 10805 Channel %1 block %2 repositioning after switch of geometry axes or transformation |
| 10810 Channel %1 block %2 master spindle not defined |
| 10820 Channel %1 rotary axis/spindle %2 not defined |
| 10860 Channel %1 block %2 feedrate not programmed |
| 10861 Channel %1 block %3 velocity of positioning axis %2 is zero |
| 10862 Channel %1 block %2 master spindle also used as path axis |
| 10870 Channel %1 block %2 facing axis not defined |
| 10880 Channel %1 block %2 too many empty blocks between two traversing blocks when inserting chamfers or radii |
| 10881 Channel %1 block %2 overflow of local block buffer when inserting chamfers or radii |
| 10882 Channel %1 block %2 activation of chamfers or radii (non-modal) without traversing movement in the block |
| 10883 Channel %1 block %2 chamfer or fillet has to be reduced |
| 10890 Channel %1 block %2 overflow of local block buffer when calculating splines |
| 10891 Channel %1 block %2 multiplicity of node is greater than its order |
| 10900 Channel %1 block %2 no S value programmed for constant cutting speed |
| 10910 Channel %1 block %2 excessive velocity of one path axis |
| 10911 Channel %1 block %2 transformation prohibits to traverse the pole |
| 10912 Channel %1 block %2 preprocessing and main run might not be synchronized |
| 10913 Channel %1 block %2 negative feed profile is ignored |
| 10914 Movement not possible while transformation active in channel %1, block %2 |
| 10930 Channel %1 block %2 interpolation type not allowed in stock removal contour |
| 10931 Channel %1 block %2 incorrect stock removal contour |
| 10932 Channel %1 block %2 preparation of contour has been restarted |
| 10933 Channel %1 block %2 contour program does not contain enough contour blocks |
| 10934 Channel %1 block %2 array for contour segmentation is set too small |
| 10940 Channel %1 block %2 curve table %3: delete/overwrite not possible |
| 10941 Channel %1 block %2 curve table %3: NC memory full |
| 10942 Channel %1 block %2 curve table %3: illegal instruction during definition |
| 10943 Channel %1 block %2 curve table %3: direction reversal of lead value in the block not allowed |
| 10944 Channel %1 block %2 curve table %3: illegal transformation |
| 10945 Channel %1 block %2 curve table %3: illegal coupling of axes |
| 10946 Channel %1 block %2 curve table %3: no contour defined |
| 10947 Channel %1 block %2 curve table %3: contour not continuous |
| 10948 Channel %1 block %2 curve table %3: position jump at end of period |
| 10949 Channel %1 block %2 curve table %3: missing master axis motion |
| 10950 Channel %1 calculation of arc length function too inaccurate |
| 10951 Channel %1 block %2 curve table %3: following value period is zero |
| 10955 Channel %1 block %2 curve table %3: missing master axis motion |
| 10956 Channel %1 block %2 curve table %3: NC memory limit DRAM reached |
| 10960 Channel %1 block %2 COMPCURV/COMPCAD and radius compensation cannot be used simultaneously |
| 10961 Channel %1 block %2 maximum cubic polynomials are allowed on active radius compensation. |
| 10962 Channel %1 block %2 function %3 not possible with path correction |
| 12000 Channel %1 block %2 address %3 programmed repeatedly |
| 12010 Channel %1 block %2 address %3 address type programmed too often |
| 12020 Channel %1 block %2 illegal address modification |
| 12030 Channel %1 block %2 invalid parameter or data type in %3 |
| 12040 Channel %1 block %2 expression %3 is not of data type AXIS |
| 12050 Channel %1 block %2 DIN address %3 not configured |
| 12060 Channel %1 block %2 same G group programmed repeatedly |
| 12070 Channel %1 block %2 too many syntax-defining G functions |
| 12080 Channel %1 block %2 syntax error in text %3 |
| 12090 Channel %1 block %2 unexpected parameter %3 |
| 12100 Channel %1 block %2 number of passes %3 not permissible |
| 12110 Channel %1 block %2 block syntax cannot be interpreted |
| 12120 Channel %1 block %2 G function not separately programmed |
| 12130 Channel %1 block %2 illegal tool orientation |
| 12140 Channel %1 block %2 functionality %3 not implemented |
| 12150 Channel %1 block %2 operation %3 not compatible with data type |
| 12160 Channel %1 block %2 range of values exceeded |
| 12170 Channel %1 block %2 identifier %3 defined repeatedly |
| 12180 Channel %1 block %2 illegal chaining of operators %3 |
| 12190 Channel %1 block %2 variable of type ARRAY has too many dimensions |
| 12200 Channel %1 block %2 symbol %3 cannot be created |
| 12210 Channel %1 block %2 string %3 too long |
| 12220 Channel %1 block %2 binary constant %3 in string too long |
| 12230 Channel %1 block %2 hexadecimal constant %3 in string too long |
| 12240 Channel %1 block %2 tool orientation %3 defined repeatedly |
| 12250 Channel %1 block %2 nested macro %3 not possible |
| 12260 Channel %1 block %2 too many initialization values specified %3 |
| 12261 Channel %1 block %2 initialization of %3 not allowed |
| 12270 Channel %1 block %2 macro identifier %3 already defined |
| 12280 Channel %1 block %2 maximum macro length %3 exceeded |
| 12290 Channel %1 block %2 arithmetic variable % 3 not defined |
| 12300 Channel %1 block %2 call-by-reference parameter missing on subroutine call %3 |
| 12310 Channel %1 block %2 axis parameter missing on procedure call %3 |
| 12320 Channel %1 block %2 parameter %3 is no variable |
| 12330 Channel %1 block %2 type of parameter %3 incorrect |
| 12340 Channel %1 block %2 number of parameters too high %3 |
| 12350 Channel %1 block %2 parameter %3 no longer possible |
| 12360 Channel %1 block %2 dimension of parameter %3 incorrect |
| 12370 Channel %1 block %2 range of values %3 not permissible |
| 12380 Channel %1 block %2 maximum memory capacity reached |
| 12390 Channel %1 block %2 initialization value %3 cannot be converted |
| 12400 Channel %1 block %2 field %3 element does not exist |
| 12410 Channel %1 block %2 incorrect index type for %3 |
| 12420 Channel %1 block %2 identifier %3 too long |
| 12430 Channel %1 block %2 specified index is invalid |
| 12440 Channel %1 block %2 maximum number of formal arguments exceeded |
| 12450 Channel %1 block %2 label defined twice |
| 12460 Channel %1 block %2 maximum number of symbols exceeded with %3 |
| 12470 Channel %1 block %2 G function %3 is unknown |
| 12475 Channel %1 block %2 invalid G function number %3 programmed |
| 12480 Channel %1 block %2 subroutine %3 already defined |
| 12490 Channel %1 block %2 access permission level %3 is not valid |
| 12500 Channel %1 block %2 in this module %3 is not possible |
| 12510 Channel %1 block %2 too many machine data %3 |
| 12520 Channel %1 block %2 too many tool parameters %3 |
| 12530 Channel %1 block %2 invalid index for %3 |
| 12540 Channel %1 block %2 Block is too long or too complex |
| 12550 Channel %1 block %2 name %3 not defined or option not installed |
| 12552 Channel %1 block %2 tool/magazine OEM parameter not defined. Option not set.Option not set. |
| 12560 Channel %1 block %2 programmed value %3 exceeds allowed limits |
| 12570 Channel %1 block %2 too many motion synchronous actions in %3 |
| 12571 Channel %1 block %2 %3 not permissible for motion synchronous action |
| 12572 Channel %1 block %2 %3 only permissible for motion synchronous action |
| 12580 Channel %1 block %2 %3 not permissible for assignment in motion synchronous action |
| 12581 Channel %1 block %2 invalid read access to %3 while in motion synchronous action |
| 12582 Channel %1 block %2 field index %3 incorrect |
| 12583 Channel %1 block %2 variable %3 no system variable |
| 12584 Channel %1 block %2 variable %3 cannot be read synchronously with motion |
| 12585 Channel %1 block %2 variable %3 cannot be changed synchronously with motion |
| 12586 Channel %1 block %2 motion synchronous action: type conflict in variable %3 |
| 12587 Channel %1 block %2 motion synchronous action: operation/function %3 not allowed |
| 12588 Channel %1 block %2 motion synchronous action: address %3 not allowed |
| 12589 Channel %1 block %2 motion synchronous action: variable %3 not allowed with modal ID |
| 12590 Channel %1 block %2 global user data cannot be created |
| 12600 Channel %1 block %2 invalid line checksum |
| 12610 Channel %1 block %2 accessing single character with call-by-reference parameter not possible %3 |
| 12620 Channel %1 block %2 accessing this variable as single character not possible |
| 12630 Channel %1 block %2 skip ID/label in control structure not allowed |
| 12640 Channel %1 block %2 invalid nesting of control structures |
| 12641 Channel %1 block %2 maximum nesting depth of control structures exceeded |
| 12650 Channel %1 block %2 axis identifier %3 different in channel %4 |
| 12660 Channel %1 block %2 motion synchronous action: variable %3 reserved for motion synchronous actions and technology cycles |
| 12661 Channel %1 block %2 technology cycle %3: no further subprogram call possible |
| 12700 Channel %1 block %2 contour definition programming not allowed as modal sub program is active |
| 12701 Channel %1 block %2 illegal interpolation type for contour definition active |
| 12710 Channel %1 block %2 illegal language element in external language mode |
| 12720 Channel %1 block %2 program number for macro call (G65/G66) missing |
| 12722 Channel %1 block %2 multiple ISO_2/3 macro or cycle calls in the block |
| 12724 Channel %1 block %2 no radius programmed for cylinder interpolation activation/deactivation |
| 12726 Channel %1 block %2 illegal plane selection with parallel axes |
| 12728 Channel %1 block %2 distance for double turret not set |
| 12730 Channel %1 block %2 no valid transformation machine data parametrized |
| 12740 Channel %1 block %2 modal macro call %3 not possible |
| 14000 Channel %1 block %2 illegal end of file |
| 14001 Channel %1 block %2 illegal end of block |
| 14009 Channel %1 block %2 illegal program path %3 |
| 14010 Channel %1 block %2 invalid default parameter in subroutine call |
| 14011 Channel %1 block %2 program %3 not existing or will be edited |
| 14012 Channel %1 block %2 maximum subroutine level exceeded |
| 14013 Channel %1 block %2 number of subroutine passes invalid |
| 14014 Channel %1 selected program %3 not available or will be edited |
| 14015 Channel %1 block %2 program %3 is not enabled |
| 14016 Channel %1 block %2 error when calling the subroutine via M/T function |
| 14017 Channel %1 block %2 syntax error when calling the subroutine via M function |
| 14020 Channel %1 block %2 wrong value or wrong number of parameters on function or procedure call |
| 14021 Channel %1 block %2 wrong value or wrong number of parameters on function or procedure call |
| 14025 Channel %1 block %2 motion synchronous action: illegal modal ID |
| 14026 Channel %1 block %2 motion synchronous action: invalid polynomial number in the FCTDEF command |
| 14030 Channel %1 block %2 combine OSCILL and POSP during oscillation with in feed motion |
| 14033 Channel %1 block %2 involute: no end point programmed |
| 14034 Channel %1 block %2 involute: angle of rotation too large |
| 14035 Channel %1 block %2 involute: start point invalid |
| 14036 Channel %1 block %2 involute: end point invalid |
| 14037 Channel %1 block %2 involute: radius invalid |
| 14038 Channel %1 block %2 involute not definable: end point error |
| 14039 Channel %1 block %2 involute: end point programmed several times |
| 14040 Channel %1 block %2 error in end point of circle |
| 14045 Channel %1 block %2 error in tangential circle programming |
| 14048 Channel %1 block %2 wrong number of revolutions in circle programming |
| 14050 Channel %1 block %2 nesting depth for arithmetic operations exceeded |
| 14051 Channel %1 block %2 arithmetic error in part program |
| 14060 Channel %1 block %2 invalid skip level with differential block skip |
| 14070 Channel %1 block %2 memory for variables not sufficient for subroutine call |
| 14080 Channel %1 block %2 jump destination %3 not found |
| 14082 Channel %1 block %2 label %3 program section not found |
| 14085 Channel %1 block %2 instruction not allowed |
| 14088 Channel %1 block %2 axis %3 doubtful position |
| 14090 Channel %1 block %2 illegal D number |
| 14091 Channel %1 block %2 illegal function, index %3 %3 |
| 14092 Channel %1 block %2 axis %3 is wrong axis type |
| 14093 Channel %1 block %2 path interval |
| 14094 Channel %1 block %2 polynominal degree greater than 3 programmed for polynominal interpolation |
| 14095 Channel %1 block %2 radius for circle programming too small |
| 14096 Channel %1 block %2 illegal type conversion |
| 14097 Channel %1 block %2 string cannot be converted to AXIS type |
| 14098 Channel %1 block %2 conversion error: no valid number found |
| 14099 Channel %1 block %2 result in string concatenation too long |
| 14100 Channel %1 block %2 orientation transformation not available |
| 14101 Channel %1 block %2 orientation transformation not active |
| 14102 Channel %1 block %2 polynominal degree greater than 5 programmed for orientation vector angle |
| 14110 Channel %1 block %2 Euler angles and orientation vector components programmed |
| 14111 Channel %1 block %2 Euler angles, orientation vector and transformation axes programmed |
| 14112 Channel %1 block %2 programmed orientation path not possible |
| 14113 Channel %1 block %2 programmed lead angle too large |
| 14114 Channel %1 block %2 programmed tilt angle too large |
| 14115 Channel %1 block %2 illegal definition of workpiece surface |
| 14116 Channel %1 block %2 absolute orientation programmed while ORIPATH is active |
| 14117 Channel %1 block %2 no angle or direction of the cone programmed |
| 14118 Channel %1 block %2 no end orientation programmed |
| 14119 Channel %1 block %2 no intermediate orientation programmed |
| 14120 Channel %1 block %2 plane determination for programmed orientation not possible |
| 14122 Channel %1 block %2 angle and direction of the cone programmed |
| 14123 Channel %1 block %2 nutation angle of the cone too small |
| 14124 Channel %1 block %2 start tangent for orientation is zero |
| 14125 Channel %1 block %2 programmed rotation is not possible |
| 14129 Channel %1 block %2 orientation angles and orientation vector components programmed |
| 14130 Channel %1 block %2 too many initialization values given |
| 14131 Channel %1 block %2 orientation axes and lead/tilt angles programmed |
| 14132 Channel %1 block %2 orientation axes incorrectly configured |
| 14133 Channel %1 block %2 G code for orientation definition not allowed |
| 14134 Channel %1 block %2 G code for orientation interpolation not allowed |
| 14140 Channel %1 block %2 position programming without transformation not allowed |
| 14144 Channel %1 block %2 PTP movement not allowed |
| 14146 Channel %1 block %2 CP or PTP movement without transformation not allowed |
| 14148 Channel %1 illegal reference system for Cartesian manual traverse |
| 14150 Channel %1 block %2 illegal tool carrier number programmed or declared (MD) |
| 14151 Channel %1 block %2 illegal tool carrier rotation |
| 14152 Channel %1 block %2 tool carrier: invalid orientation. Error code: %3 |
| 14153 Channel %1 block %2 unknown tool carrier type: %3 |
| 14154 Channel %1 block %2 The amount of fine correction in parameter %3 of the orientable tool holder %4 is too large |
| 14155 Channel %1 block %2 invalid base frame definition for tool carrier offset |
| 14156 Channel %1 toolholder selection error at reset |
| 14157 Channel %1 block %2 illegal interpolation type with MOVT |
| 14159 Channel %1 block %2 more than two angles programmed with ROTS or AROTS |
| 14160 Channel %1 block %2 tool length selection without geometry axis specification |
| 14165 Channel %1 block %2 active T number does not match selected tool |
| 14170 Channel %1 block %2 illegal interpolation type with tool length compensation |
| 14180 Channel %1 block %2 H number is not defined |
| 14185 Channel %1 block %2 D number is not defined |
| 14190 Channel %1 block %2 H number with G49 |
| 14195 Channel %1 block %2 D number with G49 |
| 14197 Channel %1 block %2 D number and H number programmed simultaneously |
| 14198 Channel %1 block %2 illegal change of tool direction with tool offset |
| 14199 Channel %1 block %2 illegal plane change for tool with diameter component |
| 14200 Channel %1 block %2 negative polar radius |
| 14210 Channel %1 block %2 polar angle too large |
| 14250 Channel %1 block %2 negative pole radius |
| 14260 Channel %1 block %2 pole angle too large |
| 14270 Channel %1 block %2 pole programmed incorrectly |
| 14280 Channel %1 block %2 polar coordinates programmed incorrectly |
| 14290 Channel %1 block %2 poly nominal degree greater than 5 programmed for poly nominal interpolation |
| 14300 Channel %1 block %2 overlaid handwheel motion activated incorrectly |
| 14310 Handwheel %1 configuration incorrect or inactive |
| 14400 Channel %1 block %2 tool radius compensation active at transformation switchover |
| 14401 Channel %1 block %2 transformation not available |
| 14402 Channel %1 block %2 spline active at transformation change |
| 14403 Channel %1 block %2 preprocessing and main run might not be synchronized |
| 14404 Channel %1 block %2 illegal parametrization of transformation |
| 14410 Channel %1 block %2 spline active at geometry axis changeover |
| 14411 Channel %1 block %2 tool radius compensation active at geometry axis changeover |
| 14412 Channel %1 block %2 transformation active at geometry axis changeover |
| 14413 Channel %1 block %2 fine tool correction: changeover geometry/channel axis not allowed |
| 14414 Channel %1 block %2 GEOAX function: incorrect call |
| 14415 Channel %1 block %2 tangent control: changeover geometry/channel axis not allowed |
| 14420 Channel %1 block %2 index axis %3 frame not allowed |
| 14500 Channel %1 block %2 illegal DEF or PROC instruction in the part program |
| 14510 Channel %1 block %2 PROC instruction missing on subroutine call |
| 14520 Channel %1 block %2 illegal PROC instruction in data definition section |
| 14530 Channel %1 block %2 EXTERN and PROC instruction do not correspond |
| 14600 Channel %1 block %2 reload buffer %3 cannot be established |
| 14601 Channel %1 block %2 reload buffer could not be deleted |
| 14602 Channel %1 block %2 timeout during EXTCALL |
| 14610 Channel %1 block %2 compensation block not possible |
| 14650 Channel %1 block %2 SETINT instruction with invalid ASUP input |
| 14660 Channel %1 block %2 SETINT instruction with invalid priority |
| 14700 Channel %1 block %2 timeout during command to interpreter |
| 14701 Channel %1 block %2 number of available NC blocks reduced by %3 |
| 14710 Channel %1 block %2 error in initialization sequence in function %3 |
| 14720 Channel %1 block %2 axes for centerless transformation not available |
| 14730 Channel %1 block %2 conflict at activation of centerless transformation |
| 14740 Channel %1 block %2 no tool data available for centerless grinding |
| 14745 Channel %1 block %2 centerless grinding not active |
| 14750 Channel %1 block %2 too many auxiliary functions programmed |
| 14751 Channel %1 block %2 resources for motion synchronous actions not sufficient (code: %3) |
| 14752 Channel %1 block %2 DELDTG | STOPREOF conflict |
| 14753 Channel %1 block %2 motion synchronous actions with illegal interpolation type |
| 14754 Channel %1 block %2 motion synchronous actions and wrong feed type |
| 14755 Channel %1 block %2 motion synchronous actions without traverse motion |
| 14756 Channel %1 block %2 motion synchronous action and wrong value |
| 14757 Channel %1 block %2 motion synchronous action and wrong type |
| 14758 Channel %1 block %2 programmed value not available |
| 14759 Channel %1 block %2 motion synchronous action and wrong axis type |
| 14760 Channel %1 block %2 auxiliary function of a group programmed repeatedly |
| 14761 Channel %1 block %2 motion synchronous action: DELDTG function not allowed with active tool radius compensation |
| 14762 Channel %1 block %2 too many PLC variables programmed |
| 14763 Channel %1 block %2 too many link variables programmed |
| 14764 NCU link cannot transfer all link variables immediately |
| 14765 NCU link cannot transfer all link variables |
| 14766 NCU link is heavily loaded, impending memory shortage |
| 14767 Machine data matching via NCU link not complete |
| 14770 Channel %1 block %2 auxiliary function programmed incorrectly |
| 14780 Channel %1 block %2 unreleased option used |
| 14790 Channel %1 block %2 axis %3 programmed by PLC |
| 14800 Channel %1 block %2 programmed path speed less or equal to zero |
| 14810 Channel %1 block %2 negative axis speed programmed for positioning axis %3 |
| 14811 Channel %1 block %2 incorrect value range for acceleration of axis/spindle %3 |
| 14812 Channel %1 block %2 SOFTA not available for axis %3 |
| 14815 Channel %1 block %2 negative thread lead change programmed |
| 14820 Channel %1 block %2 negative value for maximum spindle speed programmed with constant cutting speed |
| 14821 Channel %1 block %2 error in selection or deselection of GWPS |
| 14822 Channel %1 block %2 incorrect programming of GWPS |
| 14823 Channel %1 block %2 error on selection or deselection of tool monitoring |
| 14824 Channel %1 block %2 conflict with GWPS |
| 14840 Channel %1 block %2 incorrect value range for constant cutting speed |
| 14900 Channel %1 block %2 center point and end point programmed simultaneously |
| 14910 Channel %1 block %2 invalid angle of aperture for programmed circle |
| 14920 Channel %1 block %2 intermediate point of circle incorrect |
| 15000 Channel %1 block %2 channel-sync instruction using illegal mark |
| 15010 Channel %1 block %2 program coordination instruction with invalid channel number |
| 15020 Channel %1 block %2 CHANDATA instruction cannot be executed. Channel %3 is not active |
| 15021 Channel %1 block %2 CHANDATA instruction with invalid channel number |
| 15025 CHANDATA(%2): channel is not active. Channel data will be ignored. |
| 15030 Channel %1 block %2 different measurement system settings |
| 15100 Channel %1 block %2 REORG abort caused by log file overflow |
| 15110 Channel %1 block %2 REORG not possible |
| 15150 Channel %1 block %2 reload from external aborted |
| 15160 Channel %1 block %2 wrong preprocessing configuration |
| 15165 Channel %1 block %2 error when translating or interpreting PLC Asup %3 |
| 15166 Channel %1 user system asup _N_ASUP_SPF not available |
| 15170 Channel %1 block %2 program %3 could not be compiled |
| 15171 Channel %1 block %2 compiled program %3 older than the relevant subroutine |
| 15175 Channel %1 block %2 program %3. Interfaces could not be built |
| 15180 Channel %1 block %2 program %3 cannot be executed as INI file |
| 15185 Channel %1 %2 errors in INI file |
| 15190 Channel %1 block %2 not enough free memory for subroutine call |
| 15300 Channel %1 block %2 invalid number-of-passed-blocks during block search |
| 15310 Channel %1 block %2 file requested during block search is not available |
| 15320 Channel %1 block %2 invalid block search command |
| 15330 Channel %1 block %2 invalid block number as search target |
| 15340 Channel %1 block %2 invalid label as search target |
| 15350 Channel %1 block %2 search target not found |
| 15360 Channel %1 illegal target of block search (syntax error) |
| 15370 Channel %1 target of block search not found |
| 15380 Channel %1 block %2 illegal incremental programming in axis %3 |
| 15390 Channel %1 block %2 %3 not executed during block search |
| 15395 Channel %1 master-slave not executable during block search |
| 15400 Channel %1 block %2 selected initial init file does not exist |
| 15410 Channel %1 block %2 initialization file contains invalid M function |
| 15420 Channel %1 block %2 instruction in current mode not allowed |
| 15450 Channel %1 block %2 compiled program cannot be stored |
| 15460 Channel %1 block %2 syntax error with modal function |
| 15500 Channel %1 block %2 illegal angle of shear |
| 15700 Channel %1 block %2 illegal cycle alarm number %3 |
| 15800 Channel %1 block %2 wrong starting conditions for CONTPRON/CONTDCON |
| 15810 Channel %1 block %2 wrong array dimension for CONTPRON/CONTDCON |
| 15900 Channel %1 block %2 touch probe not allowed |
| 15910 Channel %1 block %2 touch probe not allowed |
| 15950 Channel %1 block %2 no traverse motion programmed |
| 15960 Channel %1 block %2 no traverse motion programmed |
| 16000 Channel %1 block %2 invalid value for lifting direction |
| 16005 Channel %1 block %2 invalid value for lifting distance |
| 16010 Channel %1 block %2 machining stop after lift fast |
| 16015 Channel %1 block %2 wrong axis identifier %3 |
| 16016 Channel %1 block %2 no retraction position programmed for axis %3 |
| 16020 Channel %1 repositioning in block %2 is not possible |
| 16100 Channel %1 block %2 spindle %3 not available in the channel |
| 16105 Channel %1 block %2 spindle %3 cannot be assigned |
| 16110 Channel %1 block %2 spindle %3 for dwell time not in control mode |
| 16120 Channel %1 block %2 invalid index for tool fine compensation |
| 16130 Channel %1 block %2 instruction not allowed with FTOCON |
| 16140 Channel %1 block %2 FTOCON not allowed |
| 16150 Channel %1 block %2 invalid spindle number with PUTFTOCF |
| 16200 Channel %1 block %2 spline and polynominal interpolation not available |
| 16300 Channel %1 block %2 denominator polynominal with zero places within parameter range not allowed |
| 16400 Channel %1 block %2 positioning axis %3 cannot participate in spline |
| 16410 Channel %1 block %2 axis %3 is not a geometry axis |
| 16420 Channel %1 block %2 axis %3 programmed repeatedly |
| 16421 Channel %1 block %2 angle %3 programmed repeatedly in the block |
| 16422 Channel %1 block %2 angle %3 programmed repeatedly in the block |
| 16423 Channel %1 block %2 angle %3 programmed repeatedly in the block |
| 16424 Channel %1 block %2 coordinate %3 programmed repeatedly in the block |
| 16430 Channel %1 block %2 geometry axis %3 cannot traverse as positioning axis in rotated coordinate system |
| 16440 Channel %1 block %2 rotation programmed for non-existent geometry axis |
| 16500 Channel %1 block %2 chamfer or rounding negative |
| 16510 Channel %1 block %2 no facing axis available |
| 16700 Channel %1 block %2 axis %3 invalid feed type |
| 16710 Channel %1 block %2 axis %3 master spindle not programmed |
| 16715 Channel %1 block %2 axis %3 spindle not in standstill |
| 16720 Channel %1 block %2 axis %3 thread lead is zero |
| 16730 Channel %1 block %2 axis %3 wrong parameter |
| 16740 Channel %1 block %2 no geometry axis programmed |
| 16750 Channel %1 block %2 axis %3 SPCON not programmed |
| 16751 Channel %1 block %2 spindle/axis %3 SPCOF not executable |
| 16755 Channel %1 block %2 no stop required |
| 16760 Channel %1 block %2 axis %3 S value missing |
| 16761 Channel %1 block %2 axis/spindle %3 not programmable in the channel |
| 16762 Channel %1 block %2 spindle %3 thread function is active |
| 16763 Channel %1 block %2 axis %3 programmed speed is illegal (zero or negative) |
| 16770 Channel %1 block %2 axis %3 no measuring system available |
| 16771 Channel %1 following axis %2 overlaid movement not enabled |
| 16776 Channel %1 block %2 curve table %3 does not exist for axis %4 |
| 16777 Channel %1 block %2 coupling: following axis %3 for lead axis %4 not available |
| 16778 Channel %1 block %2 coupling: Ring coupling at following axis %3 and leading axis %4 impermissible |
| 16779 Channel %1 block %2 coupling: too many couplings for axis %3, see active leading axis %4 |
| 16780 Channel %1 block %2 following spindle/axis missing |
| 16781 Channel %1 block %2 master spindle/axis missing |
| 16782 Channel %1 block %2 following spindle/axis %3 not available |
| 16783 Channel %1 block %2 master spindle/axis %3 not available |
| 16785 Channel %1 block %2 identical spindles/axes %3 |
| 16787 Channel %1 block %2 coupling parameter not changeable |
| 16788 Channel %1 block %2 cyclic coupling |
| 16789 Channel %1 block %2 multiple link |
| 16790 Channel %1 block %2 Parameter is zero or missing |
| 16791 Channel %1 block %2 parameter is not relevant |
| 16792 Channel %1 block %2 too many couplings for axis/spindle %3 |
| 16793 Channel %1 block %2 coupling of axis %3 prohibits transformation change |
| 16794 Channel %1 block %2 coupling of axis/spindle %3 prohibits reference point approach |
| 16795 Channel %1 block %2 string cannot be interpreted |
| 16796 Channel %1 block %2 coupling not defined |
| 16797 Channel %1 block %2 coupling is active |
| 16798 Channel %1 block %2 axis %3 is following axis and prohibits axis container rotation |
| 16799 Channel %1 block %2 axis %3 is master axis and prohibits axis container rotation |
| 16800 Channel %1 block %2 traverse instruction DC/CDC for axis %3 not allowed |
| 16810 Channel %1 block %2 traverse instruction ACP for axis %3 not allowed |
| 16820 Channel %1 block %2 traverse instruction ACN for axis %3 not allowed |
| 16830 Channel %1 block %2 incorrect position programmed for axis/spindle %3 |
| 16903 Channel %1 program control: action %2 not allowed in the current state |
| 16904 Channel %1 program control: action %2 not allowed in the current state |
| 16905 Channel %1 program control: action %2 not allowed |
| 16906 Channel %1 program control: action %2 is aborted due to an alarm |
| 16907 Channel %1 action %2 only possible in stop state |
| 16908 Channel %1 action %2 only possible in reset state or at the block end |
| 16909 Channel %1 action %2 not allowed in current mode |
| 16911 Channel %1 mode change is not allowed |
| 16912 Channel %1 program control: action %2 only possible in reset state |
| 16913 Mode group %1 channel %2 mode change: action %3 not allowed |
| 16914 Mode group %1 channel %2 mode change: action %3 not allowed |
| 16915 Channel %1 action %2 not allowed in the current block |
| 16916 Channel %1 repositioning: action %2 not allowed in the current state |
| 16918 Channel %1 for action %2 all channels must be in reset state |
| 16919 Channel %1 action %2 is not allowed due to a pending alarm |
| 16920 Channel %1 action %2 is already active |
| 16921 Channel %1 mode group %2 machine data: channel/mode group assignment not allowed or assigned twice |
| 16922 Channel %1 subprograms: action %2 maximum nesting depth exceeded |
| 16923 Channel %1 program control: action %2 not allowed in the current state |
| 16924 Channel %1 caution: program test modifies tool management data |
| 16925 Channel %1 program control: action %2 not allowed in the current state, action %3 active |
| 16926 Channel %1 channel coordination: action %2 not allowed in block %3, marker %4 is already set |
| 16927 Channel %1 action %2 at active interrupt treatment not allowed |
| 16928 Channel %1 interrupt treatment: action %2 not possible |
| 16930 Channel %1: preceding block and current block %2 must be separated through an executable block |
| 16931 Channel %1 subprograms: action %2 maximum nesting depth exceeded |
| 16932 Channel %1 conflict when activating user data type %2 |
| 16933 Channel %1 interrupt treatment: action %2 not allowed in the current state |
| 16934 Channel %1 interrupt treatment: action %2 not possible due to stop |
| 16935 Channel %1 action %2 not possible due to search run |
| 16936 Channel %1 action %2 not possible due to active dry run |
| 16937 Channel %1 action %2 not possible due to program test |
| 16938 Channel %1 action %2 aborted due to active gear change |
| 16939 Channel %1 action %2 rejected due to active gear change |
| 16940 Channel %1 action %2 wait for gear change |
| 16941 Channel %1 action %2 rejected because no program event has been executed yet |
| 16942 Channel %1 start program command action %2 not possible |
| 16943 Channel %1 action %2 not possible due to ASUP |
| 16944 Channel %1 action %2 not possible due to active search blocks |
| 16945 Channel %1 action %2 delayed up to the block end |
| 16946 Channel %1 start via START is not allowed |
| 16947 Channel %1 start via PLC is not allowed |
| 16948 Channel %1 dependent channel %2 still active |
| 16949 Correspondence between marker of channel %1 and channel %2 is invalid. |
| 16950 Channel %1 search run with hold block |
| 16951 Channel %1 search run in a program section that cannot be searched |
| 17000 Channel %1 block %2 maximum number of symbols exceeded |
| 17001 Channel %1 block %2 no memory left for tool/magazine data |
| 17010 Channel %1 block %2 no memory left |
| 17020 Channel %1 block %2 illegal array index 1 |
| 17030 Channel %1 block %2 illegal array index 2 |
| 17040 Channel %1 block %2 illegal axis index |
| 17050 Channel %1 block %2 illegal value |
| 17055 Channel %1 block %2 GUD variable not existing |
| 17060 Channel %1 block %2 requested data area too large |
| 17070 Channel %1 block %2 data is write-protected |
| 17080 Channel %1 block %2 %3 value below lower limit |
| 17090 Channel %1 block %2 %3 value exceeds upper limit |
| 17095 Channel %1 block %2 invalid value |
| 17100 Channel %1 block %2 digital input/comparator no. %3 not activated |
| 17110 Channel %1 block %2 digital output no. %3 not activated |
| 17120 Channel %1 block %2 analog input no. %3 not activated |
| 17130 Channel %1 block %2 analog output no. %3 not activated |
| 17140 Channel %1 block %2 NCK output %3 is assigned to a function via machine data |
| 17150 Channel %1 block %2 maximum of %3 NCK outputs programmable in the block |
| 17160 Channel %1 block %2 no tool selected |
| 17170 Channel %1 block %2 number of symbols too large |
| 17180 Channel %1 block %2 illegal D number |
| 17181 Channel %1 block %2 T no.= %3, D no.= %4 not existing |
| 17182 Channel %1 block %2 illegal sum correction number |
| 17188 Channel %1 D number %2 defined in tool T no. %3 and %4 |
| 17189 Channel %1 D number %2 of tools defined on magazine/location %3 and %4 |
| 17190 Channel %1 block %2 illegal T number |
| 17191 Channel %1 block %2 T= %3 not existing, program %4 |
| 17192 TO unit %1 invalid tool designation of %2, duplo no. %3. No more replacement tools possible in %4. |
| 17193 Channel %1 block %2 the active tool is no longer on toolholder no./spindle no. %3, program %4 |
| 17194 Channel %1 block %2 no suitable tool found |
| 17200 Channel %1 block %2 deleting tool data not possible |
| 17202 Channel %1 block %2 deleting magazine data not possible |
| 17210 Channel %1 block %2 access to variable not possible |
| 17212 Channel %1 tool management: Load manual tool %3, duplo no. %2 onto spindle/ toolholder %4 |
| 17214 Channel %1 tool management: remove manual tool %3 from spindle/toolholder %2 |
| 17216 Channel %1 tool management: remove manual tool from spindle/toolholder %4 and load manual tool %3, duplo no. %2 |
| 17220 Channel %1 block %2 tool not existing |
| 17230 Channel %1 block %2 Duplo no. already assigned |
| 17240 Channel %1 block %2 illegal tool definition |
| 17250 Channel %1 block %2 illegal magazine definition |
| 17260 Channel %1 block %2 illegal magazine location definition |
| 17262 Channel %1 block %2 illegal tool adapter operation |
| 17270 Channel %1 block %2 call-by-reference: illegal variable |
| 17500 Channel %1 block %2 axis %3 is not an indexing axis |
| 17501 Channel %1 block %2 indexing axis %3 with Hirth tool system is active |
| 17502 Channel %1 block %2 indexing axis %3 with Hirth tooth system stop is delayed |
| 17503 Channel %1 block %2 indexing axis %3 with Hirth tooth system and axis not referenced |
| 17510 Channel %1 block %2 invalid index for indexing axis %3 |
| 17600 Channel %1 block %2 preset on transformed axis %3 not possible |
| 17605 Channel %1 block %2 axis %3 transformation active: inhibits rotation of axis container |
| 17610 Channel %1 block %2 axis %3 involved in the transformation, action cannot be carried out |
| 17620 Channel %1 block %2 approaching fixed point for transformed axis %3 not possible |
| 17630 Channel %1 block %2 referencing for transformed axis %3 not possible |
| 17640 Channel %1 block %2 spindle operation for transformed axis %3 not possible |
| 17650 Channel %1 block %2 machine axis %3 not programmable |
| 17800 Channel %1 block %2 illegally coded position programmed |
| 17900 Channel %1 block %2 axis %3 is no machine axis |
| 18000 Channel %1 block %2 NCK-specific protection zone %3 wrong. Error code %4 |
| 18001 Channel %1 block %2 channel-specific protection zone %3 incorrect. Error code %4 |
| 18002 Channel %1 block %2 NCK protection zone %3 cannot be activated. Error code %4 |
| 18003 Channel %1 block %2 NCK protection zone %3 cannot be activated.Error code %4 |
| 18004 Channel %1 block %2 orientation of workpiece-related protection zone %3 does not correspond to the orientation of tool-related protection zone %4 |
| 18005 Channel %1 block %2 serious error in definition of NCK-specific protection zone %3 |
| 18006 Channel %1 block %2 serious error in definition of channel-specific protection zone %3 |
| 18100 Channel %1 block %2 invalid value assigned to FXS[] |
| 18101 Channel %1 block %2 invalid value assigned to FXST[] |
| 18102 Channel %1 block %2 invalid value assigned to FXSW[] |
| 18200 Channel %1 block %2 curve table: block search stop not allowed with definition CTABDEF |
| 18201 Channel %1 block %2 curve table: table %3 does not exist |
| 18202 Channel %1 block %2 curve table: instruction CTABEND without CTABDEF not allowed |
| 18300 Channel %1 block %2 frame: fine shift not possible |
| 18310 Channel %1 block %2 frame: illegal rotation |
| 18311 Channel %1 block %2 frame: illegal instruction |
| 18312 Channel %1 block %2 frame: fine shift not configured |
| 18313 Channel %1 block %2 frame: illegal switchover of geometry axes |
| 18314 Channel %1 block %2 frame: type conflict |
| 18400 Channel %1 block %2 language change not possible: |
| 20000 Channel %1 axis %2 reference cam not reached |
| 20001 Channel %1 axis %2 no cam signal present |
| 20002 Channel %1 axis %2 zero mark not found |
| 20003 Channel %1 axis %2 measuring system error |
| 20004 Channel %1 axis %2 reference mark missing |
| 20005 Channel %1 axis %2 reference point approach aborted |
| 20006 Channel %1 axis %2 reference point creep velocity not reached |
| 20007 Channel %1 axis %2 reference point approach requires 2 measuring systems |
| 20008 Channel %1 axis %2 reference point approach requires second referenced measuring system |
| 20050 Channel %1 axis %2 handwheel mode active |
| 20051 Channel %1 axis %2 handwheel mode not possible |
| 20052 Channel %1 axis %2 already active |
| 20053 Channel %1 axis %2 DRF, FTOCON, external zero point offset not possible |
| 20054 Channel %1 axis %2 wrong index for indexing axis in JOG mode |
| 20055 Channel %1 master spindle not present in JOG mode |
| 20056 Channel %1 axis %2 no revolutional feedrate possible. Axis/spindle %3 stationary |
| 20057 Channel %1 block %2 revolutional feedrate for axis/spindle %3 is |
| 20058 Channel %1 axis %2 revolutional feedrate: illegal feed source |
| 20060 Channel %1 axis %2 cannot be traversed as geometry axis |
| 20061 Channel %1 axis %2 cannot be traversed as orientation axis |
| 20062 Channel %1 axis %2 already active |
| 20063 Channel %1 axis %2 orientation axes cannot be traversed without transformation |
| 20065 Channel %1 master spindle not defined for geometry axes in JOG mode |
| 20070 Channel %1 axis %2 programmed end position is behind software limit switch %3 |
| 20071 Channel %1 axis %2 programmed end position is behind working area limit %3 |
| 20072 Channel %1 axis %2 is not an indexing axis |
| 20073 Channel %1 axis %2 cannot be repositioned |
| 20074 Channel %1 axis %2 wrong index position |
| 20075 Channel %1 axis %2 can currently not oscillate |
| 20076 Channel %1 axis %2 oscillating mode change not possible |
| 20077 Channel %1 axis %2 programmed position is behind software limit switch %3 |
| 20078 Channel %1 axis %2 programmed position is behind working area limit %3 |
| 20079 Channel %1 axis %2 oscillation path length %3 |
| 20080 Channel %1 axis %2 no handwheel assigned for overlaid motion |
| 20085 Channel %1 contour handwheel: traverse direction or overtravel of beginning of block not allowed |
| 20090 Axis %1 travel to fixed stop not possible. Check programming and axis data. |
| 20091 Axis %1 has not reached fixed stop |
| 20092 Axis %1 travel to fixed stop still active |
| 20093 Axis %1 standstill monitoring at fixed-stop end point has been triggered |
| 20094 Axis %1 function has been aborted |
| 20095 Axis %1 illegal torque, current torque %2 |
| 20096 Axis %1 brake test aborted, additional information %2 |
| 20100 Channel %1: invalid configuration for digitizing function |
| 20101 Communication with the digitizer not possible |
| 20102 Channel %1: No or invalid trafo at digitizing active |
| 20103 Channel %1: digitizing module does not support 3+2 axis digitizing |
| 20105 Channel %1: axes stopped by digitizer. Error code: %2 |
| 20106 Emergency stop set by the digitizer |
| 20108 Invalid data package received from the digitizer. Error codes: %1, %2 |
| 20109 Error in communication with the digitizer: status code of com-circuit: %1 |
| 20120 Axis %1: too many compensation relations |
| 20121 Axis %1: Configuration error in compensation table %2 |
| 20122 Compensation table %1: invalid axis assignment |
| 20123 Axis %1: different output assignment of multiplied tables |
| 20124 Axis %1: sum of compensation values too large |
| 20125 Axis %1: change of compensation value is too rapid |
| 20130 Channel %1 contour tunnel monitoring |
| 20140 Channel %1 motion synchronous action: traversing of command axis %2 see NC alarm %3 |
| 20141 Channel %1 motion synchronous action: illegal axis type |
| 20142 Channel %1 command axis %2: rotation of axis container already enabled |
| 20143 Channel %1 axis %2 command axis cannot be started as it is controlled by the PLC |
| 20144 Channel %1 block %2 motion synchronous action: system variable access not possible |
| 20145 Channel %1 block %2 motion synchronous action: arithmetic error |
| 20146 Channel %1 block %2 motion synchronous action: nesting depth exceeded |
| 20147 Channel %1 block %2 motion synchronous action: command not executable |
| 20148 Channel %1 block %2 motion synchronous action: internal error %3 |
| 20149 Channel %1 block %2 motion synchronous action: illegal index |
| 20150 Channel %1 tool management: PLC terminates interrupted command |
| 20160 Channel %1 tool management: PLC can terminate only incorrectly aborted commands |
| 20170 Channel %1 machine data $AC_FIFO invalid |
| 20200 Channel %1 invalid spindle number %2 with tool fine compensation |
| 20201 Channel %1 spindle %2 no tool assigned |
| 20203 Channel %1 no active tool |
| 20204 Channel %1 PUTFTOC command not allowed with FTOCOF |
| 20210 Channel %1 block %3 spindle %2 wrong values for centerless grinding |
| 20211 Channel %1 block %3 spindle %2 support point beyond range limits |
| 21600 Monitoring for ESR active |
| 21610 Channel %1 axis %2 encoder %3 frequency limit exceeded |
| 21611 Channel %1 NC-controlled Extended Stop/Retract triggered |
| 21612 Channel %1 axis %2 VDI signal Servo enable reset during motion |
| 21613 Axis %1 measuring system changing |
| 21614 Channel %1 axis %2 hardware limit switch %3 |
| 21615 Channel %1 axis %2 taken from traverse mode to follow-up mode |
| 21616 Channel %1 block %2 overlaid motion active at transformation switchover |
| 21617 Channel %1 block %2 transformation does not allow to traverse the pole |
| 21618 Channel %1 as from block %2 transformation active: overlaid motion too great |
| 21619 Channel %1 block %2 transformation active: motion not possible |
| 21650 Channel %1 axis %2 overlaid motion not allowed |
| 21660 Channel %1 block %2 axis %3 conflict between SYNACT: $AA_OFF and CORROF |
| 21665 Channel %1 $AA_TOFF cleared |
| 21670 Channel %1 block %2 illegal change of tool direction with $AA_TOFF active |
| 21700 Channel %1 block %3 axis %2 touch probe already deflected, edge polarity not possible |
| 21701 Channel %1 block %3 axis %2 measurement not possible |
| 21702 Channel %1 block %3 axis %2 measurement aborted |
| 21703 Channel %1 block %3 axis %2 touch probe not deflected, illegal edge polarity |
| 21740 Output value at analog output no. %1 has been limited |
| 21750 Error during output of cam signals via timer |
| 21760 Channel %1 block %2 too many auxiliary functions programmed |
| 21800 Channel %1 workpiece setpoint %2 reached |
| 22000 Channel %1 block %3 spindle %2 change of gear stage not possible |
| 22010 Channel %1 block %3 spindle %2 actual gear stage differs from requested gear stage |
| 22011 Channel %1 block %3 spindle %2 change to programmed gear stage not possible |
| 22012 Channel %1 block %2 leading spindle %3 is in simulation. |
| 22013 Channel %1 block %2 dependent spindle %3 is in simulation. |
| 22014 Channel %1 block %2. The dynamics of leading spindle %3 and dependent spindle %4 is too variably |
| 22020 Channel %1 block %3 spindle %2 gear step change position not reached |
| 22040 Channel %1 block %3 spindle %2 is not referenced with zero marker |
| 22045 Block %2 spindle/axis %3 not available in channel %1 because active in channel %4 |
| 22050 Channel %1 block %3 spindle %2 no transition from speed control mode to position control mode |
| 22051 Channel %1 block %3 spindle %2 reference mark not found |
| 22052 Channel %1 block %3 spindle %2 no standstill on block change |
| 22053 Channel %1 block %3 spindle %2 reference mode not supported |
| 22054 Channel %1 block %3 spindle %2 improper punching signal |
| 22055 Channel %1 block %3 spindle %2 configured positioning speed is too high |
| 22060 Channel %1 position control expected for axis/spindle %2 |
| 22062 Channel %1 axis %2 reference point approach: zero marker search velocity (MD) is not reached |
| 22064 Channel %1 axis %2 reference point approach: zero marker search velocity (MD) is too high |
| 22065 Channel %1 tool management: Tool motion is not possible, as tool %2 with Duplo no. %3 is not in magazine %4 |
| 22066 Channel %1 tool management: Tool change is not possible, as tool %2 with Duplo no. %3 is not in magazine %4 |
| 22067 Channel %1 tool management: tool change not possible since there is no tool available in tool group %2 |
| 22068 Channel %1 block %2 tool management: no tool available in tool group %3 |
| 22069 Channel %1 block %2 tool management: No tool available in tool group %3, program %4 |
| 22070 TO unit %1 Please change tool T= %2 into magazine. Repeat data backup |
| 22071 TO unit %1 tool %2 duplo no. %3 is active, but not in the magazine area under consideration |
| 22100 Channel %1 block %3 spindle %2 chuck speed exceeded |
| 22200 Channel %1 spindle %2 axis stopped during tapping |
| 22250 Channel %1 spindle %2 axis stopped during thread cutting |
| 22260 Channel %1 spindle %2 thread might be damaged |
| 22270 Channel %1 block %2 maximum velocity of thread axis at position %3 reached |
| 22275 Channel %1 block %2 zero velocity of thread axis at position %3 reached |
| 22280 Channel %1 in block %2: Prog. acceleration path too short %3, %4 required |
| 22320 Channel %1 block %2 PUTFTOCF command could not be transferred |
| 22321 Channel %1 axis %2 PRESET not allowed during traverse motion |
| 22322 Channel %1 axis %2 PRESET: illegal value |
| 25000 Axis %1 hardware fault of active encoder |
| 25001 Axis %1 hardware fault of passive encoder |
| 25010 Axis %1 pollution of measuring system |
| 25011 Axis %1 pollution of passive encoder |
| 25020 Axis %1 zero mark monitoring of active encoder |
| 25021 Axis %1 zero mark monitoring of passive encoder |
| 25022 Axis %1 encoder %2 warning %3 |
| 25030 Axis %1 actual velocity alarm limit |
| 25031 Axis %1 actual velocity warning limit |
| 25040 Axis %1 standstill monitoring |
| 25042 Axis %1 standstill monitoring during torque/force limitation |
| 25050 Axis %1 contour monitoring |
| 25060 Axis %1 speed setpoint limitation |
| 25070 Axis %1 drift value too large |
| 25080 Axis %1 positioning monitoring |
| 25100 Axis %1 measuring system switchover not possible |
| 25105 Axis %1 measuring systems differ considerably |
| 25110 Axis %1 selected encoder not available |
| 25200 Axis %1 requested set of parameters invalid |
| 25201 Axis %1 drive fault |
| 25202 Axis %1 waiting for drive |
| 26000 Axis %1 clamping monitoring |
| 26001 Axis %1 parameterization error: friction compensation |
| 26002 Axis %1 encoder %2 parameterization error: number of encoder marks |
| 26003 Axis %1 parameterization error: lead screw pitch |
| 26004 Axis %1 encoder %2 parameterization error: grid point distance with linear encoders |
| 26005 Axis %1 parameterization error: output rating |
| 26006 Axis %1 encoder %2 encoder type/output type %3 not possible |
| 26007 Axis %1 QEC: invalid coarse step size |
| 26008 Axis %1 QEC: invalid fine step size |
| 26009 Axis %1 QEC: memory overflow |
| 26010 Axis %1 QEC: invalid acceleration characteristic |
| 26011 Axis %1 QEC: invalid measuring periods |
| 26012 Axis %1 QEC: feed forward control not active |
| 26014 Axis %1 machine data %2 invalid value |
| 26015 Axis %1 machine data %2[%3] invalid value |
| 26016 Axis %1 machine data %2 invalid value |
| 26017 Axis %1 machine data %2[%3] invalid value |
| 26018 Axis %1 setpoint output drive %2 used more than once |
| 26019 Axis %1 encoder %2 measurement not possible with this controller module |
| 26020 Axis %1 encoder %2 hardware fault %3 during encoder initialization |
| 26022 Axis %1 encoder %2 measurement with simulated encoder not possible |
| 26024 Axis %1 machine data %2 value changed |
| 26025 Axis %1 machine data %2[%3] value changed |
| 26030 Axis %1 encoder %2 absolute position lost |
| 26031 Axis %1 configuration error master-slave |
| 26032 Axis %1 master-slave not configured |
| 26050 Axis %1 parameter set change from %2 to %3 not possible |
| 26051 Channel %1 in block %2 unanticipated stop crossed in continuous path mode |
| 26052 Channel %1 in block %2: path velocity too high for auxiliary function output |
| 26070 Channel %1 axis %2 cannot be controlled by the PLC, max. number exceeded |
| 26072 Channel %1 axis %2 cannot be controlled by the PLC |
| 26074 Channel %1 switching off PLC control of axis %2 not allowed in the current state |
| 26080 Channel %1 retraction position of axis %2 not programmed or invalid |
| 26081 Channel %1 axis trigger of axis %2 was activated, but axis is not PLC- controlled |
| 26100 Axis %1 drive %2 sign of life missing |
| 26101 Axis %1 drive %2 communication failure |
| 26102 Axis %1 drive %2 sign of life missing |
| 26105 Drive of axis %1 not found |
| 26106 Encoder %2 of axis %1 not found |
| 26110 Independent drive stop/retract triggered |
| 27000 Axis %1 is not safely referenced |
| 27001 Axis %1 error in a monitoring channel, code %2, values: NCK %3, drive %4 |
| 27002 Axis %1 test stop is running |
| 27003 Checksum error found: %1 %2 |
| 27004 Axis %1, difference safe input %2, NCK %3, drive %4 |
| 27005 Axis %1 error in data cross check: static actual value difference |
| 27006 Axis %1 Test ext. pulse deletion running |
| 27007 Axis %1 acceptance test mode is active |
| 27008 Axis %1 SW limit switch deactivated |
| 27010 Axis %1 tolerance for safe standstill exceeded |
| 27011 Axis %1 safe velocity exceeded |
| 27012 Axis %1 safe end position exceeded |
| 27013 Axis %1 safe braking ramp exceeded |
| 27020 Axis %1 stop E triggered |
| 27021 Axis %1 stop D triggered |
| 27022 Axis %1 stop C triggered |
| 27023 Axis %1 stop B triggered |
| 27024 Axis %1 stop A triggered |
| 27030 Axis %1 function not supported on this 611D module |
| 27031 Axis %1 limit value for safe velocity %2 at gear ratio %3 too large (max. %4) |
| 27032 Axis %1 checksum error of safe monitoring. Confirmation and re-test required! |
| 27033 Axis %1 parameterization of MD %2[%3] invalid |
| 27034 Parameterization of MD %1 invalid |
| 27090 Error in data cross check NCK-PLC, %1[%2], NCK: %3; %4 ALSI |
| 27091 Error in data cross check NCK PLC, stop of %1 |
| 27092 Communication broken off during NCK PLC data cross check, error detected by %1 |
| 27093 Checksum error NCK-SPL, %1, %2, %3 |
| 27094 Write access to system variable %1 only allowed from NCK-SPL |
| 27095 %1 SPL protection not activated |
| 27096 SPL start not allowed |
| 27100 At least one axis is not safely referenced |
| 27101 Axis %1 difference in function safe operational stop, NCK: %2 drive: %3 |
| 27102 Axis %1 difference in function safe velocity %2, NCK: %3 drive: %4 |
| 27103 Axis %1 difference in function safe limit position %2, NCK: %3 drive: %4 |
| 27104 Axis %1 difference in function safe cam plus %2, NCK: %3 drive: %4 |
| 27105 Axis %1 difference in function safe cam minus %2, NCK: %3 drive: %4 |
| 27106 Axis %1 difference in function safe velocity nx, NCK: %2 drive: %3 |
| 27107 Axis %1 difference in function cam modulo monitoring, NCK: %2 drive: %3 |
| 27124 Stop A triggered at least in 1 axis |
| 27200 PROFIsafe: cycle time %1 [ms] too long |
| 27201 PROFIsafe: MD %1[%2]: bus segment %3 error |
| 27202 PROFIsafe: MD %1[%2]: address %3 error |
| 27203 PROFIsafe: MD %1[%2]: SPL assignment error |
| 27204 PROFIsafe: double assignment MD %1[%2] MD %3[%4] |
| 27220 PROFIsafe: Number of NCK F modules (%1) number of DP modules (%2) |
| 27221 PROFIsafe: NCK F module MD %1[%2] unknown |
| 27222 PROFI safe: S7 F module PROFI safe address %1 unknown |
| 27223 PROFIsafe: NCK F module MD %1[%2] is not a %3 module |
| 27224 PROFIsafe: F module MD %1[%2] MD %3[%4]: double assignment of PROFIsafe address |
| 27225 PROFIsafe: slave %1, configuration error %2 |
| 27240 PROFIsafe: DP M not running up, DP info: %1 |
| 27241 PROFIsafe: DP M version different, NCK: %1, PLC: %2 |
| 27242 PROFIsafe: F module %1, %2 faulty |
| 27250 PROFIsafe: configuration in DP M changed; error code %1 %2 |
| 27251 PROFIsafe: F module %1, %2 reports error %3 |
| 27252 PROFIsafe: Slave %1, sign-of-life error |
| 27253 PROFIsafe: communication fault F master component %1, error %2 |
| 27254 PROFIsafe: F module %1, error on channel %2; %3 |
| 27255 PROFIsafe: F module %1, general error |
| 27256 PROFIsafe: Current cycle time %1 [ms] > parameterized cycle time |
| 27299 PROFIsafe: Diagnosis %1 %2 %3 %4 |
| 28000 NCU link connection to all other NCUs of the link network has been aborted |
| 28001 NCU link connection to the NCU %1 of the link network has been aborted |
| 28002 Error on activation of machine data, NCU network-wide machine data were modified by NCU %1 |
| 28004 NCU link: NCU %1 of the link network is not on the bus |
| 28005 NCU link: NCU %1 of the link network not running synchronously |
| 28007 NCU link: conflict in configuration data of NCU %1 |
| 28008 NCU link: conflict in timer setting of NCU %1 |
| 28009 NCU link: conflict in bus parameters of NCU %1 |
| 28010 NCU link: the NCU %1 has not received a message |
| 28011 IPO time insufficient for NCU link. Link cycle time: %1 |
| 28012 NCU link: synchronization cycle signal failure %1 times |
| 28020 NCU link: too many link axes configured %1 |
| 28030 Serious alarm on NCU %1, axes in follow-up mode |
| 28031 Serious alarm on NCU %1 not yet acknowledged, axes still in follow-up mode |
| 28032 Emergency stop activated on NCU %1, axes in follow-up mode |
| 28033 Emergency stop on NCU % 1, axes still in follow-up mode |
| 29033 Channel %1 axis change of axis %2 not possible, PLC axis movement not yet completed |
| 60000 Channel %1 block %2: |
| 61000 Channel %1 block %2 no tool compensation active |
| 61001 Channel %1 block %2 thread lead incorrect |
| 61002 Channel %1 block %2 machining type wrongly defined |
| 61003 Channel %1 block %2 no feed programmed in the cycle |
| 61004 Channel %1 block %2 configuration geometry axis incorrect |
| 61005 Channel %1 block %2 3rd geometry axis not present |
| 61006 Channel %1 block %2 tool radius too large |
| 61007 Channel %1 block %2 tool radius too small |
| 61009 Channel %1 block %2 active tool number = 0 |
| 61010 Channel %1 block %2 finishing allowance too large |
| 61011 Channel %1 block %2 scaling not allowed |
| 61012 Channel %1 block %2 different scaling on the plane |
| 61013 Channel %1 block %2 basic settings were changed, program cannot be executed |
| 61101 Channel %1 block %2 reference plane incorrectly defined |
| 61102 Channel %1 block %2 no spindle direction programmed |
| 61103 Channel %1 block %2 number of drillings is zero |
| 61104 Channel %1 block %2 contour violation of slots/long holes |
| 61105 Channel %1 block %2 cutter radius too large |
| 61106 Channel %1 block %2 number or distance of circular elements |
| 61107 Channel %1 block %2 first drilling depth incorrectly defined |
| 61108 Channel %1 block %2 illegal values for parameters _RAD1 and _DP1 |
| 61109 Channel %1 block %2 parameter _CDIR incorrectly defined |
| 61110 Channel %1 block %2 finishing allowance at the base > depth infeed |
| 61111 Channel %1 block %2 infeed width > tool diameter |
| 61112 Channel %1 block %2 tool radius negative |
| 61113 Channel %1 block %2 parameter _CRAD for corner radius too large |
| 61114 Channel %1 block %2 machining direction G41/G42 incorrectly defined |
| 61115 Channel %1 block %2 approach or retract mode (straight line/circle/plane/space) incorrectly defined |
| 61116 Channel %1 block %2 approach or retraction path = 0 |
| 61117 Channel %1 block %2 active tool radius |
| 61118 Channel %1 block %2 length or width = 0 |
| 61119 Channel %1 block %2 nominal or core diameter incorrectly programmed |
| 61120 Channel %1 block %2 internal/external thread type not defined |
| 61121 Channel %1 block %2 number of teeth per cutting edge missing |
| 61122 Channel %1 block %2 safety clearance on the plane incorrectly defined |
| 61124 Channel %1 block %2 infeed width is not programmed |
| 61125 Channel %1 block %2 technology selection in parameter _TECHNO incorrectly defined |
| 61126 Channel %1 block %2 thread length too short |
| 61127 Channel %1 block %2 transmission ratio of tapping axis incorrectly defined (machine data) |
| 61128 Channel %1 block %2 dipping angle = 0 for dipping with oscillation or helix |
| 61180 Channel %1 block %2 no name assigned to swivel data block, although MD $MN_MM_NUM_TOOL_CARRIER > 1 |
| 61181 Channel %1 block %2 NCK software version unsufficient (missing TOOLCARRIER functionality) |
| 61182 Channel %1 block %2 name of swivel data block unknown |
| 61183 Channel %1 block %2 retraction mode GUD7 _TC_FR beyond value range 0
2 |
| 61184 Channel %1 block %2 no solution possible with current input angle values |
| 61185 Channel %1 block %2 no or incorrect (min > max) rotary axis angle ranges assigned |
| 61186 Channel %1 block %2 rotary axis vectors invalid > Check installation and start-up of the swivel cycle CYCLE800 |
| 61188 Channel %1 block %2 no axis name for the 1st axis assigned -> Check installation and start-up of the swivel cycle CYCLE800 |
| 61200 Channel %1 block %2 too many elements in the machining block |
| 61201 Channel %1 block %2 wrong sequence in the machining block |
| 61202 Channel %1 block %2 no technology cycle |
| 61203 Channel %1 block %2 no positioning cycle |
| 61204 Channel %1 block %2 unknown technology cycle |
| 61205 Channel %1 block %2 unknown positioning cycle |
| 61210 Channel %1 block %2 block search element not found |
| 61211 Channel %1 block %2 absolute reference missing |
| 61212 Channel %1 block %2 wrong tool type |
| 61213 Channel %1 block %2 circle radius too small |
| 61214 Channel %1 block %2 no lead programmed |
| 61215 Channel %1 block %2 raw dimension incorrectly programmed |
| 61216 Channel %1 block %2 feed/tooth only possible with milling tools |
| 61217 Channel %1 block %2 cutting speed for tool radius 0 programmed |
| 61218 Channel %1 block %2 feed/tooth programmed, but number of teeth is zero |
| 61222 Channel %1 block %2 plane infeed greater than the tool diameter |
| 61223 Channel %1 block %2 approach path too short |
| 61224 Channel %1 block %2 retract path too short |
| 61225 Channel %1 block %2 swivel data block unknown |
| 61226 Channel %1 block %2 swivel head cannot be exchanged |
| 61230 Channel %1 block %2 tool probe diameter too small |
| 61231 Channel %1 block %2 ShopMill program %3 cannot be executed, as it has not been tested by ShopMill |
| 61232 Channel %1 block %2 loading of magazine tool not possible |
| 61233 Channel %1 block %2: Thread inclination incorrectly defined |
| 61234 Channel %1 block %2 ShopMill subroutine %4 cannot be executed, as it has not been tested by ShopMill |
| 61235 Channel %1 block %2: ShopTurn program %4 cannot be executed, as it has not been tested by ShopTurn. |
| 61236 Channel %1 block %2: ShopTurn subroutine %4 cannot be executed, as it has not been tested by ShopTurn. |
| 61237 Channel %1 block %2: Retraction direction unknown. Manually retract tool! |
| 61238 Channel %1 block %2: Machining direction unknown. |
| 61239 Channel %1 block %2: Tool change point lies in the retraction area! |
| 61240 Channel %1 block %2: Wrong feed type |
| 61241 Channel %1 block %2: No retraction plane defined for this machining direction. |
| 61242 Channel %1 block %2: Wrong machining direction |
| 61243 Channel %1 block %2: Correct tool change point, tool tip is in retraction area! |
| 61244 Channel %1 block %2: Thread lead change results in an undefined thread |
| 61246 Channel %1 block %2: Safety clearance too small |
| 61247 Channel %1 block %2: Blank radius too small |
| 61248 Channel %1 block %2: Infeed too small |
| 61249 Channel %1 block %2: Number of edges too small |
| 61250 Channel %1 block %2: Key width/Edge length too small |
| 61251 Channel %1 block %2: Key width/Edge length too large |
| 61252 Channel %1 block %2: Chamfer/Radius too large |
| 61253 Channel %1 block %2: No finishing allowance programmed |
| 61254 Channel %1 block %2: Error when traversing to fixed stop |
| 61255 Channel %1 block %2: Cut-off error: Tool breakage? |
| 61301 Channel %1 block %2 measuring probe does not switch |
| 61302 Channel %1 block %2 measuring probe collision |
| 61303 Channel %1 block %2 safe area exceeded |
| 61308 Channel %1 block %2 check measuring distance 2a |
| 61309 Channel %1 block %2 check measuring probe type |
| 61310 Channel %1 block %2 scale factor is active |
| 61311 Channel %1 block %2 no D number is active |
| 61316 Channel %1 block %2 center point and radius cannot be determined. |
| 61332 Channel %1 block %2 change tool tip position |
| 61338 Channel %1 block %2 positioning velocity is zero |
| 61601 Channel %1 block %2 finished-part diameter too small |
| 61602 Channel %1 block %2 tool width incorrectly defined |
| 61603 Channel %1 block %2 groove form incorrectly defined |
| 61604 Channel %1 block %2 active tool violates programmed contour |
| 61605 Channel %1 block %2 contour incorrectly programmed |
| 61606 Channel %1 block %2 contour processing error |
| 61607 Channel %1 block %2 starting point incorrectly programmed |
| 61608 Channel %1 block %2 wrong cutting edge position programmed |
| 61609 Channel %1 block %2 form incorrectly defined |
| 61610 Channel %1 block %2 no infeed depth programmed |
| 61611 Channel %1 block %2 no intersection point found |
| 61612 Channel %1 block %2 thread axis cutting not possible |
| 61613 Channel %1 block %2 undercut position incorrectly defined |
| 61800 Channel %1 block %2: External CNC system missing |
| 61801 Channel %1 block %2: Wrong G code selected |
| 61802 Channel %1 block %2: Wrong axis type |
| 61803 Channel %1 block %2 programmed axis not present |
| 61804 Channel %1 block %2: Progr. position exceeds reference point |
| 61805 Channel %1 block %2: The value is absolutely and incrementally programmed |
| 61806 Channel %1 block %2: Incorrect axis assignment |
| 61807 Channel %1 block %2 wrong spindle direction programmed (active) |
| 61808 Channel %1 block %2: The final drilling depth or individual drilling depth is missing |
| 61809 Channel %1 block %2: Impermissible drilling position |
| 61810 Channel %1 block %2: ISO-G code not possible |
| 61811 Channel %1 block %2: Impermissible ISO axis name |
| 61812 Channel %1 block %2: Value(s) in the external cycle call incorrectly defined |
| 61813 Channel %1 block %2: GUD value incorrectly defined |
| 61814 Channel %1 block %2: Polar coordinates not possible with cycle |
| 61815 Channel %1 block %2: G40 not active |
| 61816 Channel %1 block %2: axes are not at the reference point |
| 61817 Channel %1 block %2: The axis coordinates are within the protection zone |
| 61818 Channel %1 block %2: The axis area limit values are identical |
| 62000 Channel %1 block %2: |
| 62100 Channel %1 block %2 no drilling cycle active |
| 62101 Channel %1 block %2: Incorrect cutting direction G3 is generated |
| 62103 Channel %1 block %2: The finishing allowance is not programmed |
| 62105 Channel %1 block %2 number of columns or lines is zero |
| 62180 Channel %1 block %2 no name assigned to swivel data block although machine data $MN_MM_NUM_TOOL_CARRIER > 1 |
| 62181 Channel %1 block %2 NCK software version unsufficient (missing TOOLCARRIER functionality) |
| 62182 Channel %1 block %2: Load swivel head |
| 62183 Channel %1 block %2 retraction mode GUD7 _TC_FR beyond value range 0
2 |
| 62184 Channel %1 block %2 no solution possible with current input angle values |
| 62185 Channel %1 block %2 no end stop assigned to rotary axes |
| 62186 Channel %1 block %2 illegal rotary axis vectors |
| 62187 Channel %1 block %2 name of swivel data block unknown |
| 62200 Channel %1 block %2: Start spindle |
| 63000 Channel %1 block %2: |
| 65000 Channel %1 block %2: |
| 66000 Channel %1 block %2: |
| 67000 Channel %1 block %2: |
| 68000 Channel %1 block %2: |
| 70000 Compile cycle alarm |
| 75000 OEM alarm |
| 75005 Channel %1 block %2 CLC: General programming error |
| 75010 Channel %1 block %2 CLC_LIM value exceeds MD limit |
| 75015 Channel %1 block %2 CLC(0) with active TOC |
| 75016 Channel %1 block %2 CLC: orientation changed for TRAFOOF |
| 75020 Channel %1 CLC position offset at lower limit %2 |
| 75021 Channel %1 CLC position offset at upper limit %2 |
| 75025 Channel %1 CLC stopped because sensor head has been touched |
| 75050 Channel %1 wrong MD configuration, error code %2 |
| 75051 Channel %1 CC_COPON CC_COPOFF error code %2 |
| 75060 Channel %1 tolerance window exceeded axis %2 |
| 75061 Channel %1 coupling active axis %2 |
| 75062 Channel %1 axes not in standstill axis %2 |
| 75070 Channel %1 wrong machine data for collision protection %2 |
| 75071 Channel %1 collision monitoring axis %2 |
| 75100 Too many analog axes configured |
| 75110 Axis %1 reached drift limit |
| 75200 Channel %1 wrong MD configuration, %2 incorrect |
| 75210 Channel %1 number of axes/axis assignment inconsistent |
| 75250 Channel %1 tool parameters incorrect |
| 75255 Channel %1 working area error |
| 75260 Channel %1 block %2 tool parameters incorrect |
| 75265 Channel %1 block %2 working area error |
| 75270 Channel %1 tool parameters incorrect |
| 75275 Channel %1 block %2 working area error |
| 75451 Error with definition of setpoint switchover |
| 75452 Axis %1 setpoint switchover not possible in the current state |
| 75500 Channel %1 wrong configuration |
| 75600 Channel %1 retrace support: wrong MD configuration. Error code %2 |
| 75601 Channel %1 block %2 invalid parameter in CC_PREPRE() |
| 75605 Channel %1 retrace support: internal error, error code %2 |
| 75606 Channel %1 retraceable contour was shortened |
| 75607 Channel %1 resynchronisation not possible |
| 100300 xxx not found |
| 100301 The table cannot be completely generated |
| 100302 No data available or no access authorization |
| 100303 Paging not possible |
| 100350 Display MD saved |
| 100351 Display MD take-over not possible |
| 101000 No connection to the PLC! |
| 101001 The PLC system status list cannot be read! |
| 101002 Invalid password! |
| 101003 Password for %1 is set! |
| 101004 Password for %1 is set! |
| 101005 The passwords do not match! |
| 101006 Password is deleted! |
| 101007 Password is not set! |
| 101008 Current access level: %1 |
| 101013 Input error see help (i)-key |
| 101016 Error: The operand address is greater than 65535! |
| 101017 No PLC input screen forms found! |
| 101018 Reading-in only possible in an active PLC status! |
| 101100 No access authorization! |
| 101111 No axes configured! |
| 101112 No drives configured! |
| 101113 No channels configured! |
| 101114 No MSD configured! |
| 101115 No FDD configured! |
| 101130 Error return value not defined: 00h 00h |
| 101131 No servo disable at PI start |
| 101132 Impermissible execution argument value |
| 101133 MDx120 CURRCTRL_GAIN could not be calculated |
| 101134 MDx407 SPEEDCTRL_GAIN_1 could not be calculated |
| 101135 MDx409 SPEEDCTRL_INTEGRATOR_TIME_1 could not be calculated |
| 101136 MDx150 FIELDCTRL_GAIN could not be calculated |
| 101137 MDx141 MAGNETIZING_REACTANCE=0 |
| 101138 MDx139/MDx140 MD_STATOR-/ROTOR_LEAKAGE_REACTANCE=0 |
| 101139 MDx134 MOTOR_NOMINAL_FREQUENCY=0 |
| 101140 MDx138 ROTOR_COLD_RESISTANCE = 0 |
| 101141 MDx117 MOTOR_INERTIA = 0 |
| 101142 MDx146 |
| 101143 MDx142 FIELD_WEAKENING_SPEED = 0 |
| 101144 MDx118 MOTOR_STANDSTILL_CURRENT = 0 |
| 101145 MD1104/1118 MOTOR_MAX_CURRENT/MOTOR_STANDSTILL_CURRENT > 900.0 |
| 101146 Boot file(s) saved |
| 101147 Boot file(s) deleted |
| 101148 Controller MD calculated |
| 101150 MD set active |
| 101151 Start-up successful |
| 101153 MMC-NCK communication faulty %1 %2 |
| 101154 PI service was rejected |
| 101155 Path %1 not available |
| 101156 Impermissible function |
| 101157 File %1 not available |
| 101158 Function not permitted in the current operating state. |
| 101159 Remote block in wrong state |
| 101160 Date and time of the PLC set |
| 101161 The drive is not in cyclic mode! |
| 101162 MDx134/MDx400 MOTOR_NOMINAL_FREQUENCY/MOTOR_RATED_SPEED impermissible |
| 101163 MDx130 MOTOR_NOMINAL_POWER |
| 101164 MDx132 MOTOR_NOMINAL_VOLTAGE |
| 101165 MDx103 MOTOR_NOMINAL_CURRENT |
| 101166 MDx129 POWER_FACTOR_COS_PHI impermissible |
| 101167 MDx134/MDx400 MOTOR_NOMINAL_FREQUENCY/MOTOR_RATED_SPEED impermissible |
| 101168 Warning MDx142 FIELD_WEAKENING_SPEED |
| 101200 Safety-Integrated data copied |
| 101201 Safety-Integrated data confirmed |
| 101202 SI data is copied from axis %1 to drive %2 Parameters: %1 = Axis name %2 = Drive number |
| 101203 SI data not completely copied |
| 101204 SI data not confirmed |
| 101205 Drive data changed? -> Dont forget to save the boot files! |
| 101206 Search action running, pleas wait |
| 101207 Position at $MN_ |
| 101208 SI data confirmed: Axis 1 |
| 101209 SI data confirmed: Drive 1 |
| 101210 The machine data is being prepared for display |
| 101211 NCK address not changed! |
| 101212 NCK address changed! |
| 101213 Invalid NCK address. |
| 101214 Initialization of this window failed! |
| 101300 Please wait language is being changed |
| 103000 There is no correction block on the NCK |
| 103001 Selection is only possible after being enabled or in the RESET state. |
| 103002 Copying to the clipboard is not possible |
| 103003 MDI clipboard cannot be deleted |
| 103004 Block search not possible |
| 103006 Block search without calculation only possible on the main program level. |
| 103007 Ending overstore is not possible in this channel state. |
| 103008 Block search in channel %1 started please wait |
| 103009 Conflict between search type and search target! |
| 103010 Invalid file name |
| 103011 No program selected block search finished |
| 103014 Please reference the axis first |
| 104000 Current tool not found |
| 104001 No other tools available |
| 104002 No other cutting edges available |
| 104003 There arent any tools at all |
| 104004 No tool selected |
| 104005 No cutting edge selected |
| 104006 No TO area available in the current channel |
| 104007 Error during tool creation |
| 104008 Error during cutting edge creation |
| 104011 Error during tool deletion |
| 104012 No master spindle available |
| 104014 Incorrect entry |
| 104015 Number of parameters per cutting edge is zero |
| 104016 No spindle available |
| 104018 Tool not available |
| 104019 Tool type not available |
| 104020 No empty location found |
| 104023 Error during tool loading |
| 104024 Error during tool unloading |
| 104025 No magazine configured |
| 104026 Notice: Tool is being loaded! |
| 104027 Notice: Tool is being unloaded! |
| 104029 Loading to this location not possible |
| 104030 No more data available |
| 105000 Error x y |
| 105001 Cycle description sc.com not available |
| 105002 File xxx already exists |
| 105003 Workpiece xxx already exists |
| 105004 Clipboard empty! To PASTE, COPY first |
| 105005 Only workpieces can be inserted here |
| 105006 Only files can be inserted here |
| 105007 No name specified |
| 105008 Memory error while writing a cycle call |
| 105009 No write-authorization for the data |
| 105010 No data selected |
| 105011 Cycle description cov.com not available |
| 105012 The program is not or only partially editable (NC reset) |
| 105013 The copied data can be inserted with the soft key Paste |
| 105014 Error while copying! |
| 105015 Error while renaming! |
| 105016 Error while deleting! |
| 105017 Selection is only possible after being enabled or in the RESET state. |
| 105018 Error during program generation! |
| 105019 Error while opening a window! |
| 105020 Error while closing a window! |
| 105021 Error during workpiece generation! |
| 105022 Error during enabling! |
| 105023 File exists already! |
| 105024 Check values! At least 1 value lies outside the input limits! |
| 105025 Please wait, the directory is being prepared! |
| 105026 Notice! The simulated program and edited program are not the same! |
| 105030 Please wait, renumbering is being carried out! |
| 105031 Renumbering was aborted! |
| 105032 Renumbering finished! |
| 105041 Block number is too large! |
| 105042 Impermissible block number! |
| 105043 Impermissible increment! |
| 105050 Please wait: Graphic is being output! |
| 105051 Output of dynamic long texts for cycle parameterization |
| 105052 Error in the cycle description of the ! |
| 105053 No cycle available in current line! |
| 105054 Error during cycle description call! |
| 105060 Please wait: Initilization of the cycle support |
| 105061 Error when opening the file! |
| 105062 Error when closing the file! |
| 105063 Error when positioning in the file %1! |
| 105064 Error when reading the file! |
| 105070 Please wait: Initialization of the simulation started! |
| 105075 Not enough axes in the current channel? > Contour with default axis names: X, Z ! |
| 109001 No switchover: Switchover disable set in current PLC |
| 109002 No switchover: Target PLC occupied, try again |
| 109003 No switchover: Switchover disable set in target PLC |
| 109004 No switchover: PLC occupied by higher-priority MMCs |
| 109005 No switchover: No displaceable MMC at the target PLC |
| 109006 No switchover: Selected channel invalid |
| 109007 Channel switchover running |
| 109008 Activation is running |
| 111001 Non-interpretable step in line %1 |
| 111002 Insufficient memory, abort in line %1 |
| 111003 ManualTurn: %1 |
| 111004 File faulty or not available: %1 |
| 111005 Error when interpreting the contour %1 Parameters: %1 = Contour name |
| 111006 Maximum number of contour elements exceeded %1 |
| 111007 Error in line %1 %2 |
| 111008 Spindle not synchronized |
| 111009 Load new tool: T%1 Parameters: %1 = Tool number |
| 111010 Teach-in interruption: Log overflow |
| 111100 Wrong position programmed for the spindle |
| 111105 No measuring system available |
| 111106 No spindle stop for a block change |
| 111107 Reference mark not found |
| 111108 No transition from speed control mode to position control mode |
| 111109 Configured positioning velocity is too high |
| 111110 Velocity/Speed is negative |
| 111111 Setpoint speed is zero |
| 111112 Invalid gear stage |
| 111115 Programmed position was not reached |
| 111126 Absolute value minus not possible |
| 111127 Absolute value plus not possible |
| 111200 Spindle positioning error |
| 111300 NC start key defective |
| 111301 NC stop key defective |
| 111302 Spindle start key defective |
| 111303 Spindle stop key defective |
| 111304 Connection to the PLC broken off |
| 111305 Asynchronous subroutine was not executed |
| 111306 Error when selecting or deselecting constant cutting speed |
| 111307 Error when deleting handwheel offset |
| 111308 Error when setting upper spindle speed limit |
| 111309 Error when selecting tool |
| 111310 Error when selecting zero offset |
| 111311 NC start not possible: Deselect single block |
| 111400 Unknown PLC error |
| 111410 Tool %1 was created |
| 111411 %1 Tool(s) can (could) not be created |
| 111420 Error during the inch/metric conversion! Check all data! |
| 111430 Program not loaded. Error when converting old cycles in G code. No NC memory. |
| 111900 Start only possible in basic display |
| 111901 Contour is contained in the current program, machining not enabled |
| 111902 Start only with valid reference point |
| 111904 4. Axis not configured, i.e., no driven tool possible |
| 112045 Several insertion points required |
| 112046 Main contour cannot be bypassed |
| 112052 No residual material generated |
| 112057 Programmed helix violates contour |
| 112099 System-error contour pocket |
| 112100 Error during renumbering. Original state restored. |
| 112200 The contour is a step in the current program sequence. Machining not enabled |
| 112201 The contour is a step in the current automatic sequence. Machining not enabled |
| 112210 Tool axis cannot be switched over. Insufficient NC memory. |
| 112211 Tool preselection could not be processed. Insufficient NC memory. |
| 112300 Tool management type 2 not possible. Magazine not completely loaded. |
| 112301 Tool management type 2 not possible. The magazine is not sorted as in the tool list. |
| 112323 Replace swivel head. |
| 112324 Load swivel head. |
| 112325 Exchange swivel head. |
| 112326 Set swivel head |
| 112327 Angle not in permissible area |
| 112328 Angle adapted to angle grid. |
| 112329 Set swivel head/table |
| 112330 Set swivel table. |
| 112350 No swivel data set up. |
| 112360 The step was not accepted into the program sequence, as the program is running. |
| 112400 Is not available in the tool management |
| 112401 Tool could not be created |
| 112420 Error during the inch/metric conversion! Check all data! |
| 112502 Insufficient memory, abort in line %1 |
| 112504 File faulty or not available: %1 Parameters: %1 = File name |
| 112505 Error when interpreting the contour %1 |
| 112506 Maximum number of contour elements exceeded %1 |
| 112541 Program cannot be interpreted |
| 112604 Connection to the PLC broken off |
| 112605 Asynchronous subroutine was not executed |
| 112650 Unknown PLC error |
| 112999 Faulty grafic data. Exit graphic and restart |
| 120000 Area %1 cannot be loaded! Acknowledge alarm, press area switchover key! |
| 120001 Area %1 cannot be selected. Please deactivate area %2 |
| 120002 Area %1 is still active. Please deactivate area %1 |
| 120003 Area %1 cannot be deactivated. Please try again |
| 120005 Please acknowledge the dialog box in area %1 |
| 120006 The channel switchover is currently disabled by area %1. |
| 120007 The channel switchover is currently disabled. |
| 120008 Control unit switchover, PLC timeout: 001 control unit switchover, PLC timeout: 002 control unit switchover, PLC timeout: 003 |
| 120120 The alarm list is full of alarm texts: Number of alarm texts too high Alarm texts: File %1 not found alarm texts: Input/Output error in file %1 alarm texts: Input/Output error alarm texts: Error when reading from the index file alarm texts: Error when writing in the index file alarm texts: Syntax error in alarm text file %1 |
| 120200 Image preparation suppressed |
| 120201 Communication failure |
| 120202 Waiting for a connection to the NC |
| 120301 Faulty entry for hardkey Program in Keys.ini. |
| 120302 The selection is not possible. A program has to have been edited first via the area Program. |
| 120303 The selection is not possible. The edited file %1 no longer exists. |
| 120304 The selection is not possible. The file %1 has insufficient read rights. |
| 120305 Selection is not possible. The file %1 is currently being edited. |
| 120306 The selection is not possible. The file %1 is selected and active in channel %2. |
| 120307 The file %1 cannot be opened for the editor because it is selected in channel %2 for execution from external sources. |
| 120308 In the event of an emergency stop, the program %1 can only be changed in the machine/program correction area. |
| 120309 The selection is not possible. Please close the simulation and repeat the selection. |
| 120310 The selection is not possible. Please wait for the pending action or terminate it, then repeat the selection. |
| 300000 Hardware drive bus: DCM not present |
| 300001 Axis %1 drive number %2 not possible |
| 300002 Axis %1 drive number %2 assigned twice |
| 300003 Axis %1 drive %2 wrong module type %3 |
| 300004 Axis %1 drive %2 wrong drive type %3 (FDD/MSD) |
| 300005 At least one module found on drive bus that has not been configured |
| 300006 Module with drive number %1 has not been found on drive bus |
| 300007 Axis %1 drive %2 not present or inactive |
| 300008 Axis %1 drive %2 measuring circuit %3 is not available |
| 300009 Axis %1 drive %2 measuring circuit %3 wrong measuring circuit type (type %4 used) |
| 300010 Axis %1 drive %2 active without NC axis assignment |
| 300011 Axis %1 drive %2 hardware version of spindle not supported |
| 300012 Axis %1 drive %2 hardware version of control module not supported |
| 300020 Drive %1 removed for diagnosis |
| 300100 Drive power failure |
| 300101 Bus communications failure |
| 300200 Drive bus hardware fault |
| 300201 Axis %1 drive %2 timeout during access, error location %3 |
| 300202 Axis %1 drive %2 CRC error, error location %3 |
| 300300 Axis %1 drive %2 boot error, error code %3 |
| 300400 Axis %1 drive %2 system error, error codes %3, %4 |
| 300401 Drive software for type %1, block %2 missing or incorrect |
| 300402 System error in drive link. Error codes %1, %2 |
| 300403 Axis %1 drive %2 drive software and drive MD with different version numbers |
| 300404 Axis %1 drive %2 drive MD contains different drive number |
| 300405 Axis %1 drive %2 unknown drive alarm, code %3 |
| 300410 Axis %1 drive %2 error when storing a file (%3, %4) |
| 300411 Axis %1 drive %2 error when reading a file (%3, %4) |
| 300412 Error when storing a file (%1, %2) |
| 300413 Error when reading a file (%1, %2) |
| 300423 Measuring results could not be read (%1) |
| 300500 Axis %1 drive %2 system error, error codes %3, %4 |
| 300501 Axis %1 drive %2 maximum current monitoring |
| 300502 Axis %1 drive %2 maximum current monitoring of phase current R |
| 300503 Axis %1 drive %2 maximum current monitoring of phase current S |
| 300504 Axis %1 drive %2 measuring circuit error of motor measuring system |
| 300505 Axis %1 drive %2 measuring circuit error of absolute track, code %3 |
| 300506 Axis %1 drive %2 NC sign-of-life failure |
| 300507 Axis %1 drive %2 synchronization error of rotor position |
| 300508 Axis %1 drive %2 zero mark monitoring of motor measuring system |
| 300509 Axis %1 drive %2 current frequency exceeded |
| 300510 Axis %1 drive %2 error on actual current measurement zero balancing |
| 300511 Axis %1 drive %2 measuring function active |
| 300515 Axis %1 drive %2 power section heat sink temperature exceeded |
| 300604 Axis %1 drive %2 motor encoder is not adjusted |
| 300605 Axis %1 drive %2 motor change not valid |
| 300606 Axis %1 drive %2 flux controller at limit |
| 300607 Axis %1 drive %2 current controller at limit |
| 300608 Axis %1 drive %2 speed controller at limit |
| 300609 Axis %1 drive %2 encoder cut-off frequency exceeded |
| 300610 Axis %1 drive %2 rotor position identification failed |
| 300611 Axis %1 drive %2 generator mode: Motion at rotor position identification |
| 300612 Axis %1 drive %2 illegal current during rotor position identification |
| 300613 Axis %1 drive %2 maximum permissible motor temperature exceeded |
| 300614 Axis %1 drive %2 time monitoring of motor temperature |
| 300701 Axis %1 drive %2 start-up required |
| 300702 Axis %1 drive %2 base cycle time invalid |
| 300703 Axis %1 drive %2 current cycle time invalid |
| 300704 Axis %1 drive %2 speed controller cycle time invalid |
| 300705 Axis %1 drive %2 position controller cycle time invalid |
| 300706 Axis %1 drive %2 monitoring cycle time invalid |
| 300707 Axis %1 drive %2 basic cycle times of axes differ |
| 300708 Axis %1 drive %2 current controller cycle times of axes differ |
| 300709 Axis %1 drive %2 speed controller cycle times of axes differ |
| 300710 Axis %1 drive %2 position controller cycle times of axes differ |
| 300711 Axis %1 drive %2 monitoring cycle times of axes differ |
| 300712 Axis %1 drive %2 configuration of controller structure (higher dynamic response) not possible |
| 300713 Axis %1 drive %2 lead time for position controller invalid |
| 300714 Axis %1 drive %2 power section code invalid |
| 300715 Axis %1 drive %2 maximum power section current less than or equal to zero |
| 300716 Axis %1 drive %2 torque constant less than or equal to zero |
| 300717 Axis %1 drive %2 motor moment of inertia less than or equal to zero |
| 300718 Axis %1 drive %2 calculation dead time of current controller less than or equal to zero |
| 300719 Axis %1 drive %2 motor not parameterized for delta operation |
| 300720 Axis %1 drive %2 maximum motor speed invalid |
| 300721 Axis %1 drive %2 zero-load current greater than rated motor current |
| 300722 Axis %1 drive %2 zero-load motor current greater than rated current of power section |
| 300723 Axis %1 drive %2 STS configuration of axes differ |
| 300724 Axis %1 drive %2 number of pole pairs invalid |
| 300725 Axis %1 drive %2 number of encoder marks of measuring system invalid |
| 300726 Axis %1 drive %2 voltage constant is zero |
| 300727 Axis %1 drive %2 reactance less than or equal to zero |
| 300728 Axis %1 drive %2 adaption factor torque/current too high |
| 300729 Axis %1 drive %2 motor zero-speed current less than or equal to zero |
| 300730 Axis %1 drive %2 rotor resistance invalid |
| 300731 Axis %1 drive %2 rated power less than or equal to zero |
| 300732 Axis %1 drive %2 rated speed less than or equal to zero |
| 300733 Axis %1 drive %2 zero load voltage invalid |
| 300734 Axis %1 drive %2 zero load current less than or equal to zero |
| 300735 Axis %1 drive %2 field weakening speed invalid |
| 300736 Axis %1 drive %2 Lh characteristic invalid |
| 300737 Axis %1 drive %2 configuration of two EnDat encoders not possible |
| 300738 Axis %1 drive %2 module number for measuring system not possible |
| 300739 Axis %1 drive %2 measuring system already used as motor measuring system |
| 300740 Axis %1 drive %2 measuring system used several times |
| 300741 Axis %1 drive %2 asynchronous mode: feedforward control gain out of range |
| 300742 Axis %1 drive %2 voltage/frequency mode: converter frequency invalid |
| 300743 Axis %1 drive %2 function not supported on this 611D controller module |
| 300744 Axis %1 drive %2 safety monitoring checksum invalid, confirmation and acceptance test required! |
| 300745 Axis %1 drive %2 limit values for safe end positions exchanged |
| 300746 Axis %1 drive %2 SBH/SG not enabled |
| 300747 Axis %1 drive %2 monitoring cycle time MD 1300 invalid |
| 300748 Axis %1 drive %2 monitoring cycle times of both axes differ |
| 300749 Axis %1 drive %2 conversion factor between motor and load too large |
| 300750 Axis %1 drive %2 parameterization error in speed control adaption |
| 300751 Axis %1 drive %2 speed control gain too high |
| 300752 Axis %1 drive %2 blocking frequency of setpoint current filter too high |
| 300753 Axis %1 drive %2 rotor position identification current less than minimal value |
| 300754 Axis %1 drive %2 signal number of var. signaling function invalid |
| 300755 Axis %1 drive %2 voltage/frequency mode: motor is turning |
| 300756 Axis %1 drive %2 speed hysteresis of setpoint current smoothing invalid |
| 300757 Axis %1 drive %2 adaption factor of torque limit invalid |
| 300757 Axis %1 drive %2 adaption factor of torque limit invalid |
| 300758 Axis %1 drive %2 generator mode: response voltage > switch-off threshold |
| 300759 Axis %1 drive %2 generator mode: response voltage > monitoring threshold |
| 300760 Axis %1 drive %2 generator mode: emergency retraction speed > max. motor speed |
| 300761 Axis %1 drive %2 generator mode: minimum axis speed > max. motor speed |
| 300762 Axis %1 drive %2 emergency retraction mode/generator mode already active |
| 300763 Axis %1 drive %2 emergency retraction mode/generator mode invalid |
| 300764 Axis %1 drive %2 emergency retraction mode/generator mode not possible |
| 300765 Axis %1 drive %2 measurement of DC link voltage not possible |
| 300766 Axis %1 drive %2 blocking frequency > Shannon frequency |
| 300767 Axis %1 drive %2 natural frequency > Shannon frequency |
| 300768 Axis %1 drive %2 numerator bandwidth > double blocking frequency |
| 300769 Axis %1 drive %2 denominator bandwidth > double natural frequency |
| 300770 Axis %1 drive %2 format error |
| 300771 Axis %1 drive %2 asynchronous mode: converter frequency invalid |
| 300772 Axis %1 drive %2 asynchronous mode: speed control gain too high |
| 300773 Axis %1 drive %2 asynchronous mode: feedforward control structure not possible |
| 300774 Axis %1 drive %2 asynchronous mode: changeover speed invalid |
| 300775 Axis %1 drive %2 fixed link voltage of axes differ |
| 300776 Axis %1 drive %2 measuring circuit monitoring must be active |
| 300777 Axis %1 drive %2 rotor position identification current too high |
| 300778 Axis %1 drive %2 generator mode: converter frequency rotor position identification |
| 300779 Axis %1 drive %2 motor moment of inertia less than or equal to zero |
| 300780 Axis %1 drive %2 zero load current > rated motor current |
| 300781 Axis %1 drive %2 zero load current > rated current of power section |
| 300782 Axis %1 drive %2 reactance less than or equal to zero |
| 300783 Axis %1 drive %2 rotor resistance invalid |
| 300784 Axis %1 drive %2 zero load voltage invalid |
| 300785 Axis %1 drive %2 zero load current less than or equal to zero |
| 300786 Axis %1 drive %2 field weakening speed invalid |
| 300787 Axis %1 drive %2 asynchronous mode: feedforward control gain out of range |
| 300788 Axis %1 drive %2 parameterization error in current control adaption |
| 300789 Axis %1 drive %2 function not supported on this 611D controller module |
| 300799 Axis %1 drive %2 data backup and reboot required |
| 300850 Axis %1 drive %2 parameterization error in speed control adaption |
| 300854 Axis %1 drive %2 signal number of var. signaling function invalid |
| 300855 Axis %1 drive %2 voltage/frequency mode: motor is turning |
| 300858 Axis %1 drive %2 generator mode: response voltage > switch-off threshold |
| 300859 Axis %1 drive %2 generator mode: response voltage > monitoring threshold |
| 300860 Axis %1 drive %2 generator mode: emergency retraction speed > max. motor speed |
| 300861 Axis %1 drive %2 generator mode: minimum axis speed > max. motor speed |
| 300862 Axis %1 drive %2 emergency retraction mode/generator mode already active |
| 300863 Axis %1 drive %2 emergency retraction mode/generator mode invalid |
| 300864 Axis %1 drive %2 emergency retraction mode/generator mode not possible |
| 300865 Axis %1 drive %2 measurement of DC link voltage not possible |
| 300875 Axis %1 drive %2 fixed link voltage of axes differ |
| 300888 Axis %1 drive %2 parameterization error in current control adaption |
| 300900 Axis %1 drive %2 stop A triggered |
| 300901 Axis %1 drive %2 stop B triggered |
| 300906 Axis %1 drive %2 safe braking ramp exceeded |
| 300907 Axis %1 drive %2 tolerance for safe operational stop exceeded |
| 300908 Axis %1 drive %2 stop C triggered |
| 300909 Axis %1 drive %2 stop D triggered |
| 300910 Axis %1 drive %2 stop E triggered |
| 300911 Axis %1 drive %2 error in one monitoring channel |
| 300914 Axis %1 drive %2 safe velocity exceeded |
| 300915 Axis %1 drive %2 safe end positions exceeded |
| 300950 Axis %1 drive %2 is not safely referenced |
| 300951 Axis %1 drive %2 test stop is running |
| 300952 Axis %1 drive %2 acceptance test mode is active |
| 301701 Axis %1 drive %2 limit value for safe velocity too large |
| 301702 Axis %1 drive %2 track inversion incorrect |
| 301703 Axis %1 drive %2 encoder/motor type are not compatible |
| 301704 Axis %1 drive %2 pole pair width/division of linear scale (internal) out of range |
| 301705 Axis %1 drive %2 distance-coded scale incorrectly parameterized |
| 301706 Axis %1 drive %2 parameterization of cam position invalid |
| 301707 Axis %1 drive %2 parameterization of modulo value for safe cam (SN) invalid |
| 301708 Axis %1 drive %2 actual value synchronization not allowed |
| 301709 Axis %1 drive %2 submodule with integrated linearization invalid |
| 301710 Axis %1 drive %2 resolution SSI motor measuring system invalid |
| 301711 Axis %1 drive %2 transmission length SSI motor measuring system invalid |
| 301712 Axis %1 drive %2 multiturn SSI motor measuring system invalid |
| 301713 Axis %1 drive %2 resolution SSI direct measuring system invalid |
| 301714 Axis %1 drive %2 transmission length SSI direct measuring system invalid |
| 301715 Axis %1 drive %2 multiturn SSI direct measuring system invalid |
| 301716 Axis %1 drive %2 SSI direct measuring system without incremental signals not possible |
| 301717 Axis %1 drive %2 SSI transmission timeout |
| 301718 Axis %1 drive %2 combination of motor/power section invalid |
| 301719 Axis %1 drive %2 power section data incomplete |
| 310505 Axis %1 drive %2 measuring circuit error of absolute track, code %3 |
| 310606 Axis %1 drive %2 external valve voltage supply failed |
| 310607 Axis %1 drive %2 valve not responding |
| 310608 Axis %1 drive %2 speed controller at limit |
| 310609 Axis %1 drive %2 encoder cut-off frequency exceeded |
| 310610 Axis %1 drive %2 wrong piston position |
| 310611 Axis %1 drive %2 pressure sensor failed |
| 310612 Axis %1 drive %2 force limitation off |
| 310701 Axis %1 drive %2 speed controller cycle time invalid |
| 310702 Axis %1 drive %2 position controller cycle time invalid |
| 310703 Axis %1 drive %2 monitoring cycle time invalid |
| 310704 Axis %1 drive %2 speed controller cycle times of axes differ |
| 310705 Axis %1 drive %2 monitoring cycle times of axes differ |
| 310706 Axis %1 drive %2 maximum working speed invalid |
| 310707 Axis %1 drive %2 STS configuration of axes differ |
| 310708 Axis %1 drive %2 number of encoder marks of measuring system invalid |
| 310709 Axis %1 drive %2 error in piston diameter or piston rod diameter |
| 310710 Axis %1 drive %2 distance-coded scale incorrectly parameterized |
| 310750 Axis %1 drive %2 feedforward gain too high |
| 310751 Axis %1 drive %2 proportional gain for speed controller too high |
| 310752 Axis %1 drive %2 integral gain for speed controller invalid |
| 310753 Axis %1 drive %2 D component for speed controller invalid |
| 310754 Axis %1 drive %2 friction compensation gradient too high |
| 310755 Axis %1 drive %2 area factor too high |
| 310756 Axis %1 drive %2 controlled system gain is less than or equal to zero |
| 310757 Axis %1 drive %2 blocking frequency > Shannon frequency |
| 310758 Axis %1 drive %2 natural frequency > Shannon frequency |
| 310759 Axis %1 drive %2 bandwidth numerator larger than double blocking frequency |
| 310760 Axis %1 drive %2 bandwidth denominator greater than double natural frequency |
| 310761 Axis %1 drive %2 proportional gain of force controller too high |
| 310762 Axis %1 drive %2 integral gain for force controller invalid |
| 310763 Axis %1 drive %2 D component of force controller invalid |
| 310764 Axis %1 drive %2 controlled system gain for force controller is less than or equal to zero |
| 310771 Axis %1 drive %2 gain in fine area of valve characteristic is less than or equal to zero |
| 310772 Axis %1 drive %2 gain in rough area of valve characteristic is less than or equal to zero |
| 310773 Axis %1 drive %2 gain at end of saturation area of valve characteristic is less than or equal to zero |
| 310774 Axis %1 drive %2 zero area and knee area of valve characteristic overlap |
| 310775 Axis %1 drive %2 knee area and saturation area of valve characteristic overlap |
| 311710 Axis %1 drive %2 resolution SSI motor measuring system invalid |
| 311711 Axis %1 drive %2 transmission length SSI motor measuring system invalid |
| 311712 Axis %1 drive %2 multiturn SSI motor measuring system invalid |
| 311716 Axis %1 drive %2 SSI measuring system without incremental signals not possible |
| 311717 Axis %1 drive %2 SSI transmission timeout |
| 380001 Profibus-DP: startup error, reason %1 parameter %2 %3 %4. |
| 380003 Profibus-DP: operating error, reason %1,parameter %2 %3 %4. |
| 380005 Profibus-DP: bus access conflict, type %1, counter %2 |
| 380020 Profibus-DP: SDB1000 error %1 for SDB source %2 |
| 380021 Profibus-DP: default SDB1000 was loaded |
| 380022 Profibus-DP: configuration of DP master has been changed |
| 380040 Profibus-DP: configuration error %1, parameter %2 |
| 380050 Profibus-DP: multiple assignment of inputs on address %1 |
| 380051 Profibus-DP: multiple assignment of outputs on address %1 |
| 380060 Profibus-DP: alarm %1 on logical address %2 from unassigned station |
| 380070 Profibus DP: no input slot available for base address %1 (length %2) |
| 380071 Profibus DP: no output slot available for base address %1 (size %2) |
| 380072 Profibus DP: output slot for base address %1 (size %2) not allowed |
| 380075 Profibus DP: DP I/O failure slave %1 |
| 380500 Profibus-DP: fault on drive %1, code %2, value %3, time %4 |
| 400102 Delete DB 2 in the PLC and restart |
| 400103 Delete DB 3 in the PLC and restart |
| 400106 Delete DB 3 in the PLC and restart |
| 400109 Delete DB 9 in the PLC and restart |
| 400171 Delete DB 71 in the PLC and restart |
| 400172 Delete DB 72 in the PLC and restart |
| 400173 Delete DB 73 in the PLC and restart |
| 400174 Delete DB 74 in the PLC and restart |
| 400250 NCK sign-of-life monitoring |
| 400251 NCK has not started up |
| 400252 Sign-of-life monitoring |
| 400260 Failure of machine control panel 1 |
| 400261 Failure of machine control panel 2 |
| 400262 Failure of manual operating device |
| 400604 Set change with M06 in the machine data |
| 400902 Impermissible channel no. parameter in FC 9 |
| 401502 Impermissible axis no. parameter in FC 15 |
| 401602 Impermissible axis no. parameter in FC 16 |
| 401702 Impermissible spindle IF no. parameter in FC 17 |
| 401805 Impermissible axis no. parameter in FC 18 |
| 401901 Impermissible BAG no. parameter in FC 19 |
| 401902 Impermissible channel no. parameter in FC 19 |
| 402501 Impermissible BAG no. parameter in FC 25 |
| 402502 Impermissible channel no. parameter in FC 25 |
| 410150 Area in M group decoder list is too large |
| 810001 Error OB_event |
| 810002 Synchronous error |
| 810003 Asychronous error |
| 810004 Stop/Interrupt event |
| 810005 Order form execution event |
| 810006 Error communication event |
| 810007 Error H/F system event |
| 810008 Error diagnostics data from modules |
| 810009 User-diagnostics event |
|
|
Originally Posted by FailerJerry
