Nintendo switch код ошибки 2110 2003

Some Nintendo Switch users are encountering the error code 2110-2003 when they attempt to connect to their home Wi-Fi Network. This particular error code range indicates an issue that occurred prior to your console’s attempt to obtain an IP address.

After investigating this particular issue, it turns out that this problem can occur due to multiple causes. Here’s a shortlist of potential culprits that might be causing this problem:

Method 1: Power Cycle your Console

According to several affected users, this particular error code can also occur due to a glitch caused by a temporary file that your console is currently storing. In this case, you should be able to resolve this problem by going for a soft reset.

This operation will successfully clear any temp data along with the power capacitors ensuring that no temporary data can survive in between startups and cause the error code 2110-2003.

This operation was confirmed to be successful by several affected users that were previously dealing with the same problem.

Here’s a quick guide on resetting your Nintendo Switch:

1. On your console, press and hold the circular power button (located on the top of the Switch console).
2. Hold the button down until you see the system powering off (this will happen after 10 to 15 seconds).
3. Once the console is powered off, wait for a full minute to ensure that the power capacitors are drained, then press the power button again (normally) to start your console back on.
4. If you’ve done this correctly, the longer Switch logo animation should come upon the display screen. If you see it, take it as confirmation that the operation has been successfully completed.
5. After the next console startup is complete, attempt to connect to your home network once again and see if the operation is succesfull this time.

In case you still end up encountering the same 2110-2003 error code, move down to the next potential fix below.

Method 2: Rebooting or Resetting your router

In case you see the 2110-2003 error code on your Nintendo Switch console but you’re also encountering similar issues with other devices that are currently connected to your home router, you are likely dealing with a network inconsistency.

Fortunately, most occurrences of this kind can be resolved either by a simple reboot or by resetting your router settings back to their default equivalents.

If you decide to go for a simple router reboot, keep in mind that this operation will end up refreshing your IP and assigned DNS that your console is using. This doesn’t pose any data loss risk.

To perform a router reboot, use the ON/OFF button on your router (typically located on the back). When the router is ON, press it once to turn it off, then disconnect the power cable physically to ensure that the power capacitors are completely drained.

Once this time period passed, wait for Internet access to be re-established, then attempt to connect your Nintendo console to your home router again and see if the problem is now resolved.

In case the same problem is still resolved, the next course of action should be to go for a router reset. To do this, you’ll need to use the dedicated button on the back.

Note: Keep in mind that most manufacturers will make this button built-in so it’s not accidentally pressed. You’ll need a small screwdriver or a similar object to access this button.

But in case you want to go for a router reset, keep in mind that this operation will basically revert your router settings back to their default values. This means that any custom settings you’ve established inside your router settings will be lost – This includes forwarded ports, whitelisted items, blocked devices, etc.

To initiate a router reset, press and hold on the reset button (back of your router) and keep it pressed for about 10 seconds or until you see the front LEDs flashing all at once. Once you notice this behavior, release the reset button and wait for the connection to be re-established.

Once this procedure is complete, re-establish the connection tot the internet and see if the operation is complete.

Note: If you’re using PPPoE, you will need to reinsert the login credentials provided by your ISP.

Once the internet access is restored, attempt to connect your Nintendo Switch console to the Internet via your router and see if the error code is now resolved.

In case you still end up encountering the same 2110-2003 error code, move down to the next potential fix below.

Method 3: Changing the Network Security

In none of the methods above have worked for you, it’s possible that you’re actually dealing with a fairly common bug having to do with the way your Switch console knows how to manage the security method of your Wi-Fi network.

This has been an ongoing problem since the console launched back in 2017 and Nintendo still hasn’t managed to push a software update that will eradicate this problem.

But the good news is, some users have found a workaround around this problem and is super easy to deploy. As it turns out, you can most likely get this issue resolved by going to the Internet Settings of your Switch console and change the Security technology to something different.

Here’s a quick guide on attempting to resolve the 2110-2003 error code by changing the default WI-Fi technology from the Internet Settings menu:

1. From the main dashboard of your Nintendo Switch console, choose System Settings from the vertical menu on the bottom of the screen.
2. Once you’re inside the System Settings menu, select the Internet tab, then access the Internet Settings menu.
3. Next, your console will begin searching for available networks. Once you see the list of potential connections, select your home network from the list.
4. Inside the menu corresponding to your home network, access the Change Settings menu.
5. Inside the Properties Menu corresponding to your home Wi-Fi Connection, access the Security tab.
6. Inside the Security menu, choose any type of WEP (Wired Equivalent Privacy) WPA (Wireless Protected Acces) as long as you don’t leave it to None – this is the main reason why you can expect to see the 2110-2003 error code.
   Note: If you already have a WEP selected, choose another type of Wireless Equivalent Privacy.
7. Finally, save the changes in an attempt to connect to your network again to see if the operation now completes successfully.

In case the same problem is still occurring, move down to the next potential fix below.

Method 4: Switching to Google DNS

If none of the potential fixes below have worked for you, you should start to seriously consider a DNS (Domain Name Address) inconsistency. There are a lot of user reports confirming that making the switch to the DNS range provided by Google was the only thing that allowed them to fix the 2110-2003 error code.

In case you suspect that you might actually be dealing with a network inconsistency, follow the instructions below to make the switch to the DNS addresses provided by Google:

1. From the Home window of your Nintendo Switch console, choose System Settings (gear icon).
2. Once you’re inside the System Settings menu, select the Internet tab from the menu on the left, then move over to the right menu, and choose Internet Settings.
3. Next, your console will start generating a list with all the available Wi-Fi connections. Once the list is fully populated, select your Wi-Fi connection from the list (under Registered Networks).
4. After you select the correct network settings, choose Change Settings, then scroll down to the DNS Settings menu. Next, adjust the menu to say Manual so you can edit the DNS.
5. Now, under Primary DNS, press and hold the B button to delete the current value, then add 8.8.8.8 and press A to save the configuration.
6. Under Secondary DNS, press and hold the B button to delete the existing Secondary DNS. Next, delete the existing value as you did before and add 8.8.4.4 and press A to save the changes.
7. Attempt to reconnect again and see if the connection is successful this time.

Being unable to connect your Nintendo Switch to the Internet is utterly frustrating.

Multiple users get into technical complications while using this device. This is because although it has a smooth interface, Nintendo Switch is not entirely failure-proof. Before we get to the tips on how to fix Nintendo Switch Error Code 2110-2003, lets first go through some possible causes of the error;

Weak Wi-Fi signal

You could experience the error code if your Nintendo Switch is not getting a strong Wi-Fi signal. This could result from signal interference or distance from the wireless router.

Network Bugs

Some random bugs develop, although it is not an indication of a major issue with your network. Mostly, bugs that affect Nintendo Switch connectivity are temporary glitches in the software or the network itself. Fortunately, such bugs are fixed by a complete reboot of the Nintendo Switch console or the networking equipment.

Software that is out of date

Some players have confirmed that they fixed the 2110-2003 error code by updating the Console. This occurs if your Switch is mostly offline or if you only play offline games.

Unresponsive connectivity device

These are modems or wireless routers. The state of the equipment you are using can cause the 2110-2003 error code. If left running for a long time, modems or routers may freeze, become unresponsive, or stop working. Make a habit of rebooting your network equipment frequently.

A Network Security Change

This problem occurs when you force your Switch console to connect without Wi-Fi Protected Access or an active Wireless Equivalent Privacy. Nintendo Switch tends to misbehave when you do this, so ensure you always actively use a WEP/WPA security method.

Inconsistent DNS

A bad DNS range creates instability in your connection which is intolerable by the Switch console. To resolve this problem, switch to the DNS range provided by Google.

The most probable question that you have at this point is ‘How do I fix error 2110 2003?’. To resolve this issue, the possible solutions are discussed below.

Reboot your Nintendo device

Refreshing your Nintendo Switch console is one of the simplest yet most effective means of fixing the error code. This is because a reboot often clears various glitches and internal bugs.

To reboot your device, follow the steps below:

• Press and hold your Nintendo Switch’s power button for a few seconds.
• From the result-oriented window, choose “Power Options”.
• Select “Restart”

Sometimes you may find your Nintendo Switch not responding to any presses; in this case, you can force it to reboot by pressing and holding the power button for 12 seconds. Doing this forces the system to turn off and restart.

Check the wireless router distance and interference

The initial step you should take when facing a connection issue is to move closer to the wireless router. You could also try moving the router closer to the Nintendo Switch with a separation distance of about four to five feet. The Console works best if settled out in the open where it is not near an aquarium, under a metal object, or behind a television.

Ensure you also review all possible interruption causes. Disconnect or turn off all wireless devices like laptops, headphones, phones, speakers, Wi-Fi printers, and tablets. After establishing a proper connection, turn on each device separately to discover the device causing interference to the network.

Change the network security.

If none of the above solutions have worked for you, you might be dealing with a bug that has something to do with the way your Switch console knows how to manage the security of your Wi-Fi network.

Follow the steps below to change the default Wi-Fi technology:

• On the main dashboard of your Nintendo Switch, select “System Settings” from the menu at the bottom of the screen.
• Inside the system settings menu, select the Internet tab, which gives you access to the “Internet Settings” menu.
• Once your Console searches for available networks, select your home network from the list of potential connections displayed.
• Inside the menu corresponding to your home network, select the “Change Settings” menu.
• In the properties menu corresponding to your home Wi-Fi connection, select the “Security tab.”
• Inside the security menu, choose Wired Equivalence Privacy (WEP) or Wireless Protected Access (WPA). If you had WEP selected already, choose another type of WEP.
• Finally, save the changes to see if your Console works properly.

Switch to Google DNS

Many users report that switching to Google’s DNS range was the only solution in fixing their 2110 2003 error code. Thus, if none of the fixes above have worked for you, try switching to the DNS addresses provided by Google using the instructions below:

• On the home window of your Nintendo Switch console, select the “System Settings” icon.
• From inside the system settings menu, choose the internet tab from the menu on the left.
• Move over to the menu on the right to choose “Internet Settings.”
• Once your Console searches for available networks, select your home network from the list of potential connections displayed.
• After selecting the correct home network, choose “Change Settings” and scroll down to the “DNS Settings” menu. Set the menu to Manual to edit the DNS settings.
• Under “Primary DNS,” press and hold the button “B” to delete the current DNS settings value. After clearing the current value, add 8.8.8.8 and press “A” to save the configuration.
• Under “Secondary DNS,” press and hold the button “B” to delete the existing secondary DNS value. After clearing the existing value, add 8.8.4.4 and press “A” to save the changes.
• You can now try connecting Nintendo Switch to see if a successful connection will be established.

Troubleshoot your modem or router

Fixing a Nintendo Switch error code sometimes means dealing with your network devices. This can be done by power cycling the router or reset it.

Rebooting the router

Just as refreshing the Nintendo Switch console, the procedure can be performed on your wireless router. A reboot refreshes your IP and the DNS that your Console uses without losing any data loss risks. To perform a router reboot, follow the steps below:

• Press the ON/OFF button at the back of your router once to turn it off.
• Disconnect the power cable literally for 30 seconds to completely drain the power capacitors.
• Once this period has elapsed, plug it back to power and turn it on. After the internet access has been re-established, connect your Nintendo Console to the router to see if the problem has been resolved.

If, even after the router’s reboot, the problem persists, the next course of action is to reset the router. 

Resetting the router

Resetting is usually done using a dedicated button at the back of the router. It is important to note that many manufacturers make the dedicated button built-in to avoid accidental pressing. Thus, to press this button, you’ll need a paper clip, a small screwdriver, or a similar object to access this button.

While going for a router reset, you should understand that this operation reverts your router’s settings to default. This implies that any custom settings you have established in your router will be lost, including blocked devices, forwarded ports, whitelisted items, and others.

To initiate a router reset, press and hold the reset button for about 10 seconds or until you see the front LEDs flashing simultaneously. After noticing this behavior, release the reset button and wait for the re-establishment of the connection. Once the internet access is restored, connect your Nintendo Switch console to the Internet via your router to see if the 2110 2003 error code has been resolved.  

Update the Wireless Router’s Firmware

The failure of the Nintendo Switch to connect to Wi-Fi could imply that there are certain technical complications within the router and its connection. In such a case, updating the router’s firmware might come in handy in resolving the situation.

To update the Router’s Firmware, follow the steps below:

• On your PC, launch any browser and enter the router’s IP address.
• After entering the IP address, a login page will appear on the monitor.
• Key in the login credentials like the Network Name and the Security Key.
• The above step gives you access to the wireless router Settings page. On that page, move to the “Advanced” section and select “Administration” from the displayed menu.
• On the next screen, tap on the “Router Update” button or “Firmware Update” button.
• Click on the “Check” button to proceed in searching for the available firmware update.
• If there are available updates shown on the screen, select the “Install Update” button.

Wait for the downloading process to be complete and reboot the device for the updates to take effect.

Set up a New Internet Connection

The final solution we are going to discuss is setting up a new wireless network. In this setup, ensure that you double-check all settings. If you have no idea the way to go about this, follow the steps below:

• On your Nintendo Switch “Home Menu,” go to settings.
• Select Internet, then move to internet settings. Wait for your Nintendo Switch to search for available Wi-Fi signals.
• Select your Wi-Fi network and enter the correct Wi-Fi network password.
• Wait for your internet connection test result after the setup and select “OK” to complete the process.

Take Away