Massey ferguson 6713 ошибки - Решение и исправление самых разных ошибок на TopOshibok.ru

MASSEY FERGUSON Tractor Fault Codes DTC

MASSEY FERGUSON Tractor Fault Codes DTC.

Adobe Acrobat Document
51.2 KB

MASSEY FERGUSON Tractor Fault Codes DTC list

Code / Description / Solution

D101 Armrest connection not detected. Check the connection under the armrest.

D121 Generator Regulator Contact Dealer.

D122 Generator Regulator Contact Dealer.

D127 Fuel gauge Contact your dealer.

D128 Fuel Gauge Contact Dealer

D129 Battery voltage too high Contact dealer.

D130 Battery voltage too low. Make sure the battery terminals batteries securely fastened and not contaminated. Contact dealer.

D133 Accelerator Pedal Potentiometer Contact your dealer.

D134 Accelerator Pedal Potentiometer Contact your dealer.

D135 Power Controller Power Control Contact your dealer.

D136 Power Control Controller Power Control Contact your dealer.

D137 Armrest Arm Potentiometer Contact Dealer.

D138 Armrest lever potentiometer Contact your dealer.

D139 Clutch pedal Contact your dealer.

D140 Clutch Pedal Contact Dealer.

D141 Engine Speed Signal Contact your dealer.

D142 Clutch Top Sensor. Contact your dealer.

D143 Low Clutch Point Sensor Contact dealer.

D144 Power Control Controller Power Control Contact your dealer.

D145 Power Control Controller Power Control Contact your dealer.

D146 Power Control Controller Power Control Contact your dealer.

D147 Power Control Controller Power Control Contact your dealer.

D148 dashboard Contact dealer.

D149 CAN Bus Signals Contact your dealer.

D150 CAN Bus Signals Contact your dealer.

D151 Tractor speed too high. Contact dealer.

D152 instrument cluster Contact your dealer.

D153 instrument cluster Contact your dealer.

D154 CAN bus communication system Autotronic 4 with shield devices Contact your dealer.

D155 dashboard Contact dealer.

D156 Clutch Top Point Sensor Contact Dealer.

D157 Engine Speed Sensor Contact your dealer.

D158 Armrest Arm Potentiometer Contact Dealer.

D159 Power Control Controller Power Control Contact your dealer.

D160 Power Controller Power Control Contact your dealer.

D164 Communication error on the CAN bus of the EEM system from the dashboard appliances. Contact your dealer.

D170 Throttle Control Handle Contact your dealer.

D181 Hydraulic Assist Lever Contact Dealer.

D182 Auxiliary Hydraulic Lever Contact Dealer.

D183 Wheel Angle Sensor Contact your dealer.

D184 Wheel Angle Sensor Contact your dealer.

D185 Keyboard Contact your dealer.

D186 Keyboard Contact Dealer.

D189 Output voltage 9.5 V Contact your dealer.

D190 Output Voltage 9.5 V Contact Dealer

D191 Air Pressure Sensor Contact Dealer.

D192 Air Pressure Sensor Contact Dealer.

D193 Potentiometer quick change gear ratio steering gear. Contact your dealer.

D194 Potentiometer quick change gear ratio steering gear. Contact your dealer.

D195 Internal temperature sensor dashboard Contact a dealer.

D196 Internal temperature sensor dashboard Contact a dealer.

D197 Auxiliary Hydraulic System Oil Temperature Sensor. Contact your dealer.

D198 Auxiliary Hydraulic System Oil Temperature Sensor Contact Dealer

T4107 High oil pressure sensor malfunction powertrains Contact a dealer.

T4108 Included Range Sensor Fault Contact a dealer.

T4124 Parking brake sensor malfunction Contact your dealer.

T4128 Transmission Control Unit Malfunction Use box protection mode gears. Contact your dealer.

T412A Malfunction sensor gear design speed. Use box protection mode gears. Contact dealer

T412B High / low speed range switch malfunction (Hare / Turtle). Contact your dealer.

T4131 Malfunctioning shaft speed sensor malfunction. Use box protection mode gears. Contact your dealer.

T4142 Malfunctioning shaft speed sensor malfunction. Use box protection mode gears. Contact your dealer.

T4144 Engine speed sensor malfunction Use box protection mode gears. Contact your dealer.

T4145 Malfunction sensor gear design speed. Use the gearbox protection mode. Contact your dealer.

T4150 Transmission filter obstruction sensor malfunction. Contact your dealer.

T4153 High transmission oil temperature. No further movement. Contact your dealer.

T4156 Transmission filter obstruction sensor malfunction. Contact your dealer.

T4158 Transmission slip sensor malfunction. Contact your dealer.

T4159 Box protection mode failure transmission or error in this mode. Contact your dealer.

T4161 Low Speed Range Solenoid Malfunction (Turtle). Use box protection mode gears.

See also: Massey Ferguson Tractor Workshop Service Manuals PDF

Massey Ferguson 8600 series tractor

Error codes

Instrument panel error codes

No.	Component(s) concerned	Cause(s)
D	121		Alternator regulator voltage too high (filtered battery signal)
D	122		Alternator regulator voltage too low (filtered battery signal)
D	127	X197 – Diesel fuel gauge	Electrical signal too high
D	128	Electrical signal too low
D	129		Battery voltage too high (non-filtered battery signal)
D	130		Battery voltage too low (non-filtered battery signal)
D	133	X71 – Throttle pedal sensor	Electrical signal too high
D	134	Electrical signal too low
D	135	X56 – Power Control leverX71 – Throttle pedal sen- sor	Electrical signal too high – C.N.
D	136	Electrical signal too low – C.N.
D	137	X106 – Transmission lever in armrest	Electrical signal too high
D	138	Electrical signal too low
D	139	X68 – Clutch pedal sensor	Electrical signal too high
D	140	Electrical signal too low
D	141	X25 – Engine speed sensor	Engine speed signal not at maximum level
D	142	X68 – Clutch pedal sensor	Short circuit to + 12 V AC
D	143	Short circuit to + 12 V AC – C.N.
D	144	X56 – Power Control lever	Electrical signal too high
D	145	Electrical signal too low
D	146	Electrical signal too high
D	147	Electrical signal too low
D	148	X55 – Instrument panel	Attempt to program with engine running
D	149		CAN network deactivated (CAN bus off)
D	150		CAN messages lost
D	151		Tractor speed too high
D	152	X55 – Instrument panel	Hourmeter error for engine maintenance
D	153	Parameter table error
D	154		CAN communications from Autotronic 4 to DCC3 – C.N. Special failed
D	155	X55 – Instrument panel	Incorrect tractor code selected
D	156	X68 – Clutch pedal sensor	TOC stuck open
D	157	X25 – Engine speed sensor	No electrical signal
D	158	X106 – Transmission lever in armrest	Incorrect calibration of armrest lever
D	159	X56 – Power Control lever	Neutral switch error in neutral – C.N. position
D	160	Neutral switch error outside neutral – C.N. position
D	164		CAN communications from EEM to DCC3 failed
D	170	X122 – Hand throttle
D	183	X235 – Front axle steering sensor (WAS sensor)	Electrical signal too high
D	184	Electrical signal too low
D	185	X57 – DOT Matrix keyboard	Electrical signal too high
D	186	Electrical signal too low
D	189	X55 – Instrument panel	9.5 V output – electrical signal too high
D	190	9.5 V output – electrical signal too low
D	191	X168 – Pneumatic brake system pressure sensor	Electrical signal too high
D	192	Electrical signal too low

No.	Component(s) concerned	Cause(s)
D	193	X144 – Variable steering setting potentiometer (fast steering)	Electrical signal too high
D	194	Electrical signal too low
D	195	X55 – Instrument panel	Electrical signal too high
D	196	Electrical signal too low
D	197	X1 – Auxiliary hydraulic oil temperature sensor	Electrical signal too high
D	198	Electrical signal too low

Engine error codes

No.	FMI	Components concerned	Causes
E	91	4	Throttle sensor	Throttle sensor 1 LOW fault (IDLE)
E	91	3	Throttle sensor	Throttle sensor 1 HIGH fault (IDLE)
E	94	31	Fuel filter pressure sensor	Oil filter pressure LOW (with old sensor)
E	94	4	Fuel filter pressure sensor	LOW fuel filter pressure sensor fault
E	94	3	Fuel filter pressure sensor	HIGH fuel filter pressure sensor fault
E	94	2	Fuel filter pressure sensor	Fuel filter pressure NO SIGNAL
E	94	16	Fuel filter pressure sensor	Fuel filter pressure ABOVE NORMAL
E	94	18	Fuel filter pressure sensor	Fuel filter pressure BELOW NORMAL
E	97	31		Water in fuel
E	100	16	Oil pressure sensor	Oil pressure ABOVE NORMAL (9.5 bar/ 30°C)
E	100	2	Oil pressure sensor	Oil pressure NO SIGNAL
E	100	31	Oil pressure sensor	Oil pressure sensor fault
E	100	4	Oil pressure sensor	LOW oil pressure sensor fault
E	100	3	Oil pressure sensor	HIGH oil pressure sensor fault
E	100	18	Oil pressure sensor	Oil pressure LOW
E	100	1-	Oil pressure sensor	Oil pressure LOW, ALARM
E	102	4	Boost pressure sensor	LOW boost pressure sensor fault
E	102	3	Boost pressure sensor	HIGH boost pressure sensor fault
E	102	18	Boost pressure sensor	Boost pressure LOW
E	102	16	Boost pressure sensor	Boost pressure ABOVE NORMAL
E	102	2	Boost pressure sensor	Boost pressure NO SIGNAL
E	102	31	Boost pressure sensor	Inlet manifold pressure drop too HIGH at start-up
E	105	4	Inlet manifold temperature sensor	LOW inlet manifold temperature sensor fault
E	105	3	Inlet manifold temperature sensor	HIGH inlet manifold temperature sensor fault
E	105	16	Inlet manifold temperature sensor	Inlet manifold temperature ABOVE NOR- MAL (>90°C)
E	105	2	Inlet manifold temperature sensor	Inlet manifold temperature sensor NO SIGNAL
E	107	18	Air filter pressure sensor	Air filter pressure BELOW NORMAL
E	107	31	Air filter pressure sensor	Air filter pressure sensor fault
E	110	2	Coolant temperature sensor	Coolant temperature NO SIGNAL
E	110	4	Coolant temperature sensor	LOW coolant temperature sensor fault
E	110	3	Coolant temperature sensor	HIGH coolant temperature sensor fault
E	110	16	Coolant temperature sensor	Coolant temperature HIGH
E	110	0	Coolant temperature sensor	Coolant temperature HIGH, ALARM
E	157	4	Rail pressure sensor	LOW rail pressure sensor fault

No.	FMI	Components concerned	Causes
E	157	3	Rail pressure sensor	HIGH rail pressure sensor fault
E	157	16	Rail pressure sensor	Rail pressure ABOVE NORMAL
E	157	2	Rail pressure sensor	Rail pressure NO SIGNAL
E	157	1-	Rail pressure sensor	Rail pressure LOW
E	157	0	Rail pressure sensor	Rail pressure HIGH
E	168	1-	Battery voltage	Battery voltage VERY LOW (<6.5 V)
E	168	0	Battery voltage	Battery voltage VERY HIGH (>36.0 V)
E	168	2	Battery voltage	Battery voltage NO SIGNAL
E	168	18	Battery voltage	Battery voltage BELOW NORMAL (<7.8 V)
E	168	16	Battery voltage	Battery voltage ABOVE NORMAL
E	174	4	Fuel temperature sensor	LOW fuel temperature sensor fault
E	174	3	Fuel temperature sensor	HIGH fuel temperature sensor fault
E	174	16	Fuel temperature sensor	Fuel temperature ABOVE NORMAL
E	174	2	Fuel temperature sensor	Fuel temperature NO SIGNAL
E	175	4	Engine oil temperature sensor	LOW engine oil temperature sensor fault
E	175	3	Engine oil temperature sensor	HIGH engine oil temperature sensor fault
E	175	16	Engine oil temperature sensor	Engine oil temperature HIGH
E	175	2	Engine oil temperature sensor	Engine oil temperature sensor NO SIG- NAL
E	190	16	Engine speed signal	Engine speed signal ABOVE NORMAL
E	626	4		Inlet air heater control, voltage below nor- mal
E	626	3		Inlet air heater control, voltage above nor- mal
E	629	10	EEPROM	EEPROM error
E	898	4	Requested speed	Requested speed out of LOW range (<500 rpm)
E	898	3	Requested speed	Requested speed out of HIGH range (>3000 rpm)
E	1136	16	ECU temperature sensor	ECU temperature ABOVE NORMAL >115°C
E	1136	4	ECU temperature sensor	ECU LOW temperature sensor fault
E	1136	3	ECU temperature sensor	ECU HIGH temperature sensor fault
E	1136	2	ECU temperature sensor	ECU temperature NO SIGNAL
E	1378	16		Engine oil drain: delayed for too long
E	9006	31	Vehicle CAN	Vehicle CAN off
E	9008	31	CAN ID module	CAN ID module off (ECU to ID)
E	9010	4	Ambient pressure sensor	LOW ambient pressure sensor fault
E	9010	3	Ambient pressure sensor	HIGH ambient pressure sensor fault
E	9010	16	Ambient pressure sensor	Ambient pressure ABOVE NORMAL
E	9010	2	Ambient pressure sensor	Ambient pressure NO SIGNAL
E	9021	4	5 V DC supply	5 V DC supply 1 LOW fault
E	9021	3	5 V DC supply	5 V DC supply 1 HIGH fault
E	9022	4	5 V DC supply	5 V DC supply 2 LOW fault
E	9022	3	5 V DC supply	5 V DC supply 2 HIGH fault
E	9023	4	5 V DC supply	5 V DC supply 3 LOW fault
E	9023	3	5 V DC supply	5 V DC supply 3 HIGH fault
E	9024	18	Supply of sensor detecting water in the fuel	Supply voltage of sensor detecting water in fuel BELOW NORMAL
E	9024	16	Supply of sensor detecting water in the fuel	Supply voltage of sensor detecting water in fuel ABOVE NORMAL

No.	FMI	Components concerned	Causes
E	9025	31	Self-test cut-off paths	Self-test cut-off paths, monitoring
E	9026	3	Self-test cut-off paths	Self-test cut-off paths, HIGH processor voltage check
E	9027	4	Self-test cut-off paths	Self-test cut-off paths, LOW processor voltage check
E	9030	6	Main relay, short circuit to EARTH	Short circuit to EARTH, ECU main relay1
E	9030	3	Main relay, short circuit to BAT+	Short circuit to BAT+, ECU main relay1
E	9031	6	Main relay, short circuit to EARTH	Short circuit to EARTH, ECU main relay2
E	9031	3	Main relay, short circuit to BAT+	Short circuit to BAT+, ECU main relay2
E	9032	6	Main relay, short circuit to EARTH	Short circuit to EARTH, ECU main relay3
E	9032	3	Main relay, short circuit to BAT+	Short circuit to BAT+, ECU main relay3
E	9033	31	Main relay	ECU cut-off does not work
E	9034	31	Main relay	ECU cut-off did not work last time
E	9035	31		Normal recovery
E	9036	31		Total restart after 3 recoveries in 2 sec- onds
E	9070	31	Crankshaft speed sensor	Crankshaft speed signal from the TPU
E	9071	31	Crankshaft speed sensor	Crankshaft speed signal, too many pulses
E	9072	31	Crankshaft speed sensor	Crankshaft speed sensor, reverse con- nected
E	9080	31	Cam speed sensor	APS cam speed signal
E	9081	31	Cam speed sensor	TPS cam speed signal
E	9082	31	Cam speed sensor	Cam speed sensor, reverse connected
E	9083	31	Cam speed sensor	No cam speed signal detected
E	9090	31	Engine speed signal	Engine speed signal evaluation error
E	9100	31		Protection upgrade fault
E	9107	31		Invalid ECU source address selection
E	9131	6	Solenoid valve 1	Solenoid valve 1, short circuit to EARTH (bank off)
E	9131	3	Solenoid valve 1	Solenoid valve 1, short circuit between ca- bles (bank off)
E	9131	5	Solenoid valve 1	Solenoid valve 1, OPEN CIRCUIT
E	9131	31	Solenoid valve 1	Solenoid valve 1, fast decay error (bank off)
E	9131	11	Solenoid valve 1	Solenoid valve 1, current level error (bank off)
E	9132	6	Solenoid valve 2	Solenoid valve 2, short circuit to EARTH (bank off)
E	9132	3	Solenoid valve 2	Solenoid valve 2, short circuit between ca- bles (bank off)
E	9132	5	Solenoid valve 2	Solenoid valve 2, OPEN CIRCUIT
E	9132	31	Solenoid valve 2	Solenoid valve 2, fast decay error (bank off)
E	9132	11	Solenoid valve 2	Solenoid valve 2, current level error (bank off)
E	9133	6	Solenoid valve 3	Solenoid valve 3, short circuit to EARTH (bank off)
E	9133	3	Solenoid valve 3	Solenoid valve 3, short circuit between ca- bles (bank off)
E	9133	5	Solenoid valve 3	Solenoid valve 3, OPEN CIRCUIT
E	9133	31	Solenoid valve 3	Solenoid valve 3, fast decay error (bank off)

No.	FMI	Components concerned	Causes
E	9133	11	Solenoid valve 3	Solenoid valve 3, current level error (bank off)
E	9134	6	Solenoid valve 4	Solenoid valve 4, short circuit to EARTH (bank off)
E	9134	3	Solenoid valve 4	Solenoid valve 4, short circuit between ca- bles (bank off)
E	9134	5	Solenoid valve 4	Solenoid valve 4, OPEN CIRCUIT
E	9134	31	Solenoid valve 4	Solenoid valve 4, fast decay error (bank off)
E	9134	11	Solenoid valve 4	Solenoid valve 4, current level error (bank off)
E	9135	6	Solenoid valve 5	Solenoid valve 5, short circuit to EARTH (bank off)
E	9135	3	Solenoid valve 5	Solenoid valve 5, short circuit between ca- bles (bank off)
E	9135	5	Solenoid valve 5	Solenoid valve 5, OPEN CIRCUIT
E	9135	31	Solenoid valve 5	Solenoid valve 5, fast decay error (bank off)
E	9135	11	Solenoid valve 5	Solenoid valve 5, current level error (bank off)
E	9136	6	Solenoid valve 6	Solenoid valve 6, short circuit to EARTH (bank off)
E	9136	3	Solenoid valve 6	Solenoid valve 6, short circuit between ca- bles (bank off)
E	9136	5	Solenoid valve 6	Solenoid valve 6, OPEN CIRCUIT
E	9136	31	Solenoid valve 6	Solenoid valve 6, fast decay error (bank off)
E	9136	11	Solenoid valve 6	Solenoid valve 6, current level error (bank off)
E	9150	16	Rail pressure sensor	Rail pressure, negative deviation
E	9150	18	Rail pressure sensor	Rail pressure, positive deviation
E	9150	5	Rail pressure sensor	Rail pressure, leakage detected during idle
E	9150	8	Rail pressure sensor	Rail pressure, leakage detected through quantity balance
E	9150	31	Rail pressure sensor	Rail pressure, leakage detected during overrun
E	9151	31	Pressure regulating valve	PRV recognised as OPEN
E	9151	7	Pressure regulating valve	PRV is sticking
E	9152	31	Fuel filter pressure sensor	Fuel filter pressure, fluctuating
E	9153	31	Fuel filter pressure sensor	Fuel filter pressure sensor, loose contact
E	9170	6	Lift pump control	Lift pump control (ECU), short circuit to earth
E	9170	5	Lift pump control	Lift pump control (ECU), open circuit
E	9171	6	Preheater control	Preheater control, short circuit to earth
E	9171	5	Preheater control	Preheater control, open circuit
E	9172	6	Starter relay control	Start relay control, short circuit to earth (lower side)
E	9172	3	Starter relay control	Start relay control, short circuit to BAT+ (lower side)
E	9172	5	Starter relay control	Start relay control, open circuit (lower side)
E	9172	31	Starter relay control	Start relay control, excessive temperature (lower side)
E	9173	6	Starter relay control	Start relay control, short circuit to earth (upper side)

No.	FMI	Components concerned	Causes
E	9173	3	Starter relay control	Start relay control, short circuit to BAT+ (upper side)
E	9174	6	MPROP control	MPROP control, short circuit to earth
E	9174	3	MPROP control	MPROP control, short circuit to BAT+
E	9174	5	MPROP control	MPROP control, open circuit
E	9174	31	MPROP control	MPROP control, excessive temperature
E	9230	31	Diagnostic ID module	Engine specification mismatch
E	9231	31	Diagnostic ID module	Engine serial number mismatch
E	9233	31	Diagnostic ID module	ID module not present
E	9234	31	Diagnostic ID module	ID not compatible with current ECU
E	9235	31	Diagnostic ID module	ID module memory fault
E	9235	3	Diagnostic ID module	ID module, supply voltage HIGH (>32.0 V)
E	9235	4	Diagnostic ID module	ID module memory fault
E	9235	16	Diagnostic ID module	ID temperature, temperature HIGH (>95°C)
E	9236	31	Diagnostic ID module	ID module additional memory defect
E	9237	31	Diagnostic ID module	ID module, monitoring reset
E	9238	31	Diagnostic ID module	ID module, brownout reset
E	9239	31	Diagnostic ID module	Engine specification missing
E	9240	31	Diagnostic ID module	Engine serial number missing
E	9241	31	Diagnostic ID module	ID module not present, bypass active
E	9242	31	Diagnostic ID module	Generated bypass time expired
E	9243	31	Diagnostic ID module	Maximum ECU bypass time expired
E	9244	31	Diagnostic ID module	ID module recovery
E	9303	31		Speed regulator UI fault
E	9304	31		Vehicle speed missing
E	9305	31		Incorrect digital input configuration
E	9306	31		PTO input error
E	9310	31		Fault with external digital input 1
E	9311	31		Fault with external digital input 2
E	9312	31		Torque control input
E	9317	31		DCU not present

SCR system error codes

No.	FMI	Cause(s)
U	168	0	Battery voltage monitoring: Voltage higher than normal
U	168	1-	Battery voltage monitoring: Voltage lower than normal
U	168	3	Battery voltage monitoring: Voltage too high
U	168	4	Battery voltage monitoring: Voltage too low
U	441	0	Catalyst downstream temperature sensor: Temperature too high
U	441	1-	Catalyst downstream temperature sensor: Temperature too low
U	441	2	Catalyst temp. downstream sensor plaus. Error: Static Plausi- bility
U	441	3	Catalyst downstream temperature sensor: Shortcut to Battery+
U	441	4	Catalyst downstream temperature sensor: Shortcut to Ground
U	441	11	Downstream catalyst temperature – physical error: Catalyst Temperature not OK

No.	FMI	Cause(s)
U	441	16	Catalyst temp. downstream sensor plaus. error: Dynamic plau- sibility, upper threshold
U	441	18	Catalyst temp. downstream sensor plaus. Error: Dynamic plau- sibility, lower threshold
U	442	0	Catalyst upstream temperature sensor: Temperature too high
U	442	1-	Catalyst upstream temperature sensor: Temperature too low
U	442	2	Catalyst temp. upstream sensor plaus. error: Static Plausibility
U	442	3	Catalyst upstream temperature sensor: Shortcut to Battery+
U	442	4	Catalyst upstream temperature sensor: Shortcut to Ground
U	442	16	Catalyst temp. upstream sensor plaus. error: Dynamic plausibil- ity, upper threshold
U	442	18	Catalyst temp. upstream sensor plaus. error: Dynamic plausibil- ity, lower threshold
U	697	3	Back flow line heater power stage error: Shortcut to Battery+
U	697	5	Back flow line heater power stage error: Open load
U	697	6	Back flow line heater power stage error: Shortcut to Ground
U	698	3	Cooling line heater power stage error: Shortcut to Battery+
U	698	5	Cooling line heater power stage error: Open load
U	698	6	Cooling line heater power stage error: Shortcut to Ground
U	699	3	Inlet line heater power stage error: Shortcut to Battery+
U	699	5	Inlet line heater power stage error: Open load
U	699	6	Inlet line heater power stage error: Shortcut to Ground
U	700	3	Pressure line heater power stage error: Shortcut to Battery+
U	700	5	Pressure line heater power stage error: Open load
U	700	6	Pressure line heater power stage error: Shortcut to Ground
U	1079	3	Sensor Supply Voltage 1 monitoring: Shortcut to Battery+
U	1079	4	Sensor Supply Voltage 1 monitoring: Shortcut to Ground
U	1080	3	Sensor Supply Voltage 2 monitoring: Shortcut to Battery+
U	1080	4	Sensor Supply Voltage 2 monitoring: Shortcut to Ground
U	1387	0	Urea pressure monitoring: Pressure too high
U	1387	1-	Urea pressure monitoring: Pressure too low
U	1387	2	Urea pressure sensor plausibility error: Dynamic plausibility
U	1388	3	Urea pressure sensor: Shortcut to Battery+
U	1388	4	Urea pressure sensor: Shortcut to Ground
U	1388	11	Urea pressure sensor: Supply voltage above upper or below lower limit
U	1485	3	Main relay error: No shut off of main relay
U	1485	6	Main relay error: Shut off too soon
U	1677	0	Modular Heater State Machine Error: Inlet line frozen error
U	1677	1-	Modular Heater State Machine Error: Pressure line frozen error
U	1677	2	Modular Heater State Machine Error: Pressure build – up error
U	1677	3	Modular Heater State Machine Error: Back flow line frozen error
U	1761	2	Urea Tank Level Sensor error: Range error of tank level
U	1761	3	Urea Tank Level Sensor error: Signal above upper limit
U	1761	4	Urea Tank Level Sensor error: Signal below lower limit
U	1761	5	Urea tank error: Open circuit in level sensor
U	1761	6	Urea tank error: Level sensor shortcut to GND
U	1761	9	Urea Tank Level Sensor error: Message overridden
U	1761	11	Urea tank error: Tank empty

No.	FMI	Cause(s)
U	1761	14	Urea Tank Level Sensor error: Supply Signal above upper or be- low lower limit
U	1761	17	Urea tank error: Tank level low
U	1761	18	Urea tank error: Tank level VERY low
U	1761	19	Urea Tank Level Sensor error: Time out
U	2854	2	CAN Rx Frame: Range error, barometric pressure or ambient air temp
U	2854	9	CAN Rx Frame: Message overridden
U	2854	19	CAN Rx Frame: Time out
U	2855	2	CAN Rx Frame: Range error of NOx/O2 concentration or status
U	2855	9	CAN Rx Frame: Message overridden
U	2855	19	CAN Rx Frame: Time out
U	2856	2	CAN Rx Frame: Range error of NOx/O2 concentration or status
U	2856	9	CAN Rx Frame: Message overridden
U	2856	19	CAN Rx Frame: Time out
U	2857	2	CAN Bus Off: CAN Bus 2
U	2857	19	CAN Bus Off: CAN Bus 1
U	2858	2	CAN Frame Error: Long Term Error Active or Error Suppression signal is out of range
U	2859	2	Message: Range error of UreaQ/Heating or Dosing Status/PTO/ Exh. gas mass or temp.
U	2859	9	CAN Frame Error: Message overridden
U	2859	19	CAN Frame Error: Time out
U	2860	2	CAN Frame Error: Range error of Exhaust Mass flow or Dew Point ErrorCode
U	2860	9	CAN Frame Error: Message overridden
U	2860	19	CAN Frame Error: Time out
U	2861	2	CAN Frame Error: Range error of EGR Valve Control signal
U	2861	9	CAN Frame Error: Message overridden
U	2861	19	CAN Frame Error: Time out
U	2862	2	CAN Frame Error: Message overridden
U	2862	19	CAN Frame Error: Time out
U	2863	2	CAN Frame Error: Range error of Engine speed
U	2863	9	CAN Frame Error: Message overridden
U	2863	11	CAN Frame Error: Range error of Driver demand % engine torque
U	2863	13	CAN Frame Error: Range error of Engine torque
U	2863	19	CAN Frame Error: Time out
U	2864	2	CAN Frame Error: Range error of Engine inlet air mass flow rate
U	2864	9	CAN Frame Error: Message overridden
U	2864	19	CAN Frame Error: Time out
U	2865	2	CAN Frame Error: Range error of Actual Retarder Percent Torque
U	2865	9	CAN Frame Error: Message overridden
U	2865	19	CAN Frame Error: Time out
U	2866	2	CAN Frame Error: Range error of Coolant or Engine oil temper- ature signal
U	2866	9	CAN Frame Error: Message overridden
U	2866	19	CAN Frame Error: Time out
U	2867	2	CAN Frame Error: Range error of Boost pressure or Intake Man- ifold 1 Temp.

No.	FMI	Cause(s)
U	2867	9	CAN Frame Error: Message overridden
U	2867	19	CAN Frame Error: Time out
U	2868	2	CAN Frame Error: Range error of external desired NOx emis- sions
U	2868	9	CAN Frame Error: Message overridden
U	2868	19	CAN Frame Error: Time out
U	2869	2	CAN Frame Error: Range error of Fuel injection quantity
U	2869	9	CAN Frame Error: Message overridden
U	2869	10	CAN Frame Error: Range error of Urea tank level
U	2869	11	CAN Frame Error: Range error of Urea tank temperature
U	2869	12	CAN Frame Error: Range error of NOx concentration from NOx sensor 2
U	2869	13	CAN Frame Error: Range error of NOx Status byte from NOx sensor 2
U	2869	19	CAN Frame Error: Time out
U	2870	2	CAN Frame Error: Range error of Vehicle speed
U	2870	9	CAN Frame Error: Message overridden
U	2870	19	CAN Frame Error: Time out
U	2871	2	CAN Frame Time Date Error: Range error
U	2871	9	CAN Frame Time Date Error: Message overridden
U	2871	19	CAN Frame Time Date Error: Time out
U	2872	8	DCU or Heater ON error: Time out – Timer 16 elapsed
U	2872	9	DCU or Heater ON error: Time out – Timer elapsed
U	2872	10	DCU or Heater ON error: Time out – Timer elapsed
U	3031	0	Urea Tank Temperature Sensor error: Signal Above Error
U	3031	1-	Urea Tank Temperature Sensor error: Signal Above Error
U	3031	2	Urea Tank Temperature Sensor error: J1939 error of Urea tank temp. signal
U	3031	3	Urea Tank Temperature Sensor error: Signal High Error
U	3031	4	Urea Tank Temperature Sensor error: Signal Low Error
U	3031	9	Urea Tank Temperature Sensor error: Message overridden error
U	3031	11	Plausibility check of urea tank temperature sensor: Signal not plausible
U	3031	19	Urea Tank Temperature Sensor error: Time out error
U	520201	0	Monitoring of Supply Module temperature: Temperature too high
U	520201	1-	Monitoring of Supply Module temperature: Temperature too low
U	520201	3	Monitoring of Supply Module temperature: Shortcut to Bat- tery+
U	520201	4	Monitoring of Supply Module temperature: Shortcut to Ground
U	520220	9	EEPROM error: EEPROM communication error
U	520221	15	Frozen cycles counter error: Counter threshold exceeded
U	520221	16	Frozen cycles counter error: Counter2 threshold exceeded
U	520222	11	Emergency Shut Off: Over temperature detected (>85 °C)
U	520224	7	Tank Heater Valve Error: Detection of valve blocked open
U	520225	11	Urea Consumption Error: Urea consumption not plausible
U	520226	11	Urea Dosing Error: Dosing interrupted
U	520227	11	Urea Quality Error: Insufficient urea quality
U	520228	11	NOx emission control error: NOx threshold exceeded
U	520229	11	Urea Level Monitoring: Tank empty

No.	FMI	Cause(s)
U	520234	3	Diagnostic lamp power stage error: Shortcut to Battery+
U	520234	5	Diagnostic lamp power stage error: Open load
U	520234	6	Diagnostic lamp power stage error: Shortcut to Ground
U	520236	3	Filter outlet connector heater power stage error: Shortcut to Battery+
U	520236	5	Filter outlet connector heater power stage error: Open load
U	520236	6	Filter outlet connector heater power stage error: Shortcut to Ground
U	520237	3	Pressure compensation heater error: Shortcut to Battery+
U	520237	5	Pressure compensation heater error: Open load
U	520237	6	Pressure compensation heater error: Shortcut to Ground
U	520238	3	Filterbox module heater power stage error: Shortcut to Battery+
U	520238	5	Filterbox module heater power stage error: Open load
U	520238	6	Filterbox module heater power stage error: Shortcut to Ground
U	520239	3	Pump module heater power stage error: Shortcut to Battery+
U	520239	5	Pump module heater power stage error: Open load
U	520239	6	Pump module heater power stage error: Shortcut to Ground
U	520241	3	Urea dosing valve power stage error: Shortcut to Battery+
U	520241	5	Urea dosing valve power stage error: Open load
U	520241	6	Urea dosing valve power stage error: Shortcut to Ground
U	520241	7	Plausibility check of Urea Dosing Valve Stuck: UDV stuck closed
U	520241	14	Plausibility check of valve position stuck: Valve position un- known
U	520241	8	Plausibility check of Urea Dosing Valve Stuck: UDV stuck open
U	520242	3	Urea tank heater power stage error: Shortcut to Battery+
U	520242	5	Urea tank heater power stage error: Open load
U	520242	6	Urea tank heater power stage error: Shortcut to Ground
U	520243	2	Urea level plausibility error: Signal not plausible
U	520244	5	Pump speed evaluation error: Pump motor unplugged
U	520244	7	Pump speed evaluation error: Pump Motor Blocked
U	520244	8	Pump speed evaluation error: Over Speed condition
U	520244	12	Pump speed evaluation error: Pump Speed Sensor defective
U	520246	2	Plausibility check of urea tank temperature sensor: Signal not plausible
U	520248	3	Coolant control valve power stage error: Shortcut to Battery+
U	520248	5	Coolant control valve power stage error: Open load
U	520249	3	Reverting valve power stage error: Shortcut to Battery+
U	520249	5	Reverting valve power stage error: Open load
U	520249	6	Reverting valve power stage error: Shortcut to Ground
U	520250	6	Coolant control valve power stage error: Shortcut to Ground
U	520253	7	Detection of blocked pressure line: Blockage detected in state 1
U	520254	7	Detection of blocked backflow line: Block detected
U	520257	11	Static urea leakage test: Leakage detected
U	520260	7	Urea pressure buildup: Pressure buildup failed
U	520261	7	Urea pressure buildup: Error path bit 3 active
U	520262	2	Temperature plausibility during commissioning: Too cold during urea commissioning
U	520264	2	Urea pressure plausibility check: Urea pressure not plausible
U	520265	2	Urea box temperature – physical error: Box temperature too high or too low

No.	FMI	Cause(s)
U	520266	7	Vent Valve Error: CCV State machine, error path bit 3 active
U	520268	7	Reverting valve monitoring: Valve defect detected
U	520269	7	Vent Valve Error: Urea pressure not reduced
U	520273	3	Analog feedback signal for Main Relay 1: Shortcut to Battery+
U	520273	5	Analog feedback signal for Main Relay 1: Open circuit
U	520274	3	Analog feedback signal for Main Relay 2: Shortcut to Battery+
U	520274	4	Analog feedback signal for Main Relay 2: Shortcut to Ground
U	520274	5	Analog feedback signal for Main Relay 2: Open circuit
U	520275	3	Analog feedback signal for Main Relay 3: Shortcut to Battery+
U	520275	4	Analog feedback signal for Main Relay 3: Shortcut to Ground
U	520275	5	Analog feedback signal for Main Relay 3: Open circuit
U	520276	3	Monitoring of Supply Voltage: Shortcut to Battery+
U	520276	4	Monitoring of Supply Voltage: Shortcut to Ground
U	520277	3	Battery voltage monitoring: Voltage too high
U	520277	4	Battery voltage monitoring: Voltage too low
U	520296	11	Dosing Strategy Monitoring Module NOx conversion efficiency: Threshold 1 error
U	520297	11	Dosing Strategy Monitoring Module NOx conversion efficiency: Threshold 2 error
U	520298	2	Evaluation of Atmospheric Pressure: Range error of Barometric pressure
U	520299	2	Terminal 15 circuit defect: Ignition switch plausibility error
U	520301	2	NOx sensor concentration signal error: Plausibility check
U	520301	3	NOx sensor concentration signal error: Short circuit
U	520301	5	NOx sensor concentration signal error: Open wire
U	520301	11	NOx sensor concentration signal error: Other NOx errors
U	520301	17	NOx sensor concentration signal error: Sensor supply not in range
U	520302	2	NOx heater signal from NOx sensor: Plausibility check
U	520302	3	NOx heater signal from NOx sensor: Short circuit
U	520302	5	NOx heater signal from NOx sensor: Open wire
U	520302	11	NOx heater signal from NOx sensor: Other NOx errors
U	520308	2	NOx sensor plausibility error: Signal not plausible
U	520309	7	Start Up Cycle Counter for Pressure Drop during Dosing: Max. limit of counter exceeded
U	520310	2	Urea box temperature – physical error: Urea Temperature too high or too low

Transmission error codes

No.	Components concerned	Causes
T	4105	X34 – Transmission oil high pressure sensor 2	Signal error – 8.5 V supply error
T	4107	X9 – Transmission oil high pressure sensor 1	Signal error – 8.5 V supply error
T	4108	X17 – Hare/Tortoise range position sensor	Signal error – 8.5 V supply error
T	4121		Signal error
T	4127	X10 – Collecting shaft speed sensor	Signal error
T	4128	X18 – Transmission control module	Signal error
T	412A	X8 – Bevel gear theoretical speed sensor	Signal error
T	412B	X123 – Hare/Tortoise range shift switch	Signal error
T	4131	X10 – Collecting shaft speed sensor	Direction of rotation signal error

No.	Components concerned	Causes
T	4142		Rotation speed signal error
T	4144	X25 – Engine speed sensor	Signal error
T	4145	X8 – Bevel gear theoretical speed sensor	Signal error
T	4150	X20 – Transmission filter blockage switch	Filter blocked
T	4153	X19 – Transmission hydraulic oil temperature sensor	Transmission oil temperature higher than 110°C
T	4156	X20 – Transmission filter blockage switch	Signal error
T	4158	Transmission slip monitor	The transmission output speed indicates over 30% slippage compared to the value given
T	4159	Engagement of limp home mode	Manual engagement of limp home mode without reason
Limp home mode error
T	4161	X14 – Tortoise range solenoid valve	Control error when shifting from Hare to Tortoise mode
T	4162	X13 – Hare range solenoid valve	Control error when shifting from Tortoise to Hare mode
T	4163	X11 – Solenoid valve limiting speed to 30 kph	Control error
T	4164	X12 – Coupler function solenoid valve	PWM control error
T	4172	X20 – Transmission filter blockage switch	Signal error
T	4173	X19 – Transmission hydraulic oil temperature sensor	Signal error
T	4182	X8 – Bevel gear theoretical speed sensor	Inconsistent speeds
X10 – Collecting shaft speed sensor
T	4183	X8 – Bevel gear theoretical speed sensor	Inconsistent direction of rotation.
X10 – Collecting shaft speed sensor
T	4185	X25 – Engine speed sensor	Inconsistent speed
T	4186	X9 – Transmission oil high pressure sensor 1	Inconsistent values
X34 – Transmission oil high pressure sensor 2
T	4189	X19 – Transmission hydraulic oil temperature sensor	Inconsistent value
T	4192	X67 – Right-hand brake pedal sensor	Data transfer interrupted
T	4193	X66 – Left-hand brake pedal sensor	Data transfer interrupted
T	41A0	X18 – Transmission control module	Control of control module interrupted
T	41A1	X18 – Transmission control module	The angle of rotation is limited, but not by the speed limiting solenoid valve
T	41A2	X18 – Transmission control module	The CAN network control is interrupted
X174 – Autotronic 4 transmission controller
T	41A3	X18 – Transmission control module	Increment sensor signal (internal actual position sen- sor) interrupted or illogical
T	41A4	X18 – Transmission control module	Autotronic 4 signal interrupted or illogical
T	41A5	X18 – Transmission control module	Reference output (Position “0”) not found at start-up
T	41A6	X18 – Transmission control module	Reference point signal interrupted during operation
T	41B0	CAN network	Initialisation error
T	41B1	X174 – Autotronic 4 transmission controller	Illogical range shift
T	41B2	X174 – Autotronic 4 transmission controller	Faulty programming
T	41B3	X174 – Autotronic 4 transmission controller	Faulty programming
T	41B4	X174 – Autotronic 4 transmission controller	Faulty programming
T	41B5	X174 – Autotronic 4 transmission controller	Faulty programming
T	41C1	X174 – Autotronic 4 transmission controller	The engine has stalled due to transmission overload
T	41CF	X174 – Autotronic 4 transmission controller	Internal error (RAM/EEPROM)
T	41E0	X174 – Autotronic 4 transmission controller	Coupler function reference curve incorrectly inter- preted, faulty programming
X12 – Coupler function solenoid valve	Signal error

No.	Components concerned	Causes
T	41E1	X174 – Autotronic 4 transmission controller	Faulty programming
T	41E2	X174 – Autotronic 4 transmission controller	Faulty programming
T	41E3	X174 – Autotronic 4 transmission controller	Faulty programming
T	41E4	X174 – Autotronic 4 transmission controller	Faulty programming
T	41E5	X174 – Autotronic 4 transmission controller	Faulty programming
T	41E6	X174 – Autotronic 4 transmission controller	Faulty programming
T	41E7	X174 – Autotronic 4 transmission controller	Faulty programming
T	41E9	X174 – Autotronic 4 transmission controller	Faulty programming
T	41EA	X174 – Autotronic 4 transmission controller	Faulty programming
T	41EB	X17 – Hare/Tortoise range position sensor	Calibration error or sensor value out of tolerance ranges
T	41EE	X174 – Autotronic 4 transmission controller	Faulty programming
T	41EF	X174 – Autotronic 4 transmission controller	Faulty programming
T	41FF	X174 – Autotronic 4 transmission controller	Internal error (RAM/EEPROM)

4WD/Differential lock error codes

No.	Components concerned	Causes
T	5131	X137 – 4WD switch	Incorrect manual engagement signal
T	5132	Incorrect automatic engagement signal
T	5133	X5 – 4WD solenoid valve	Control error
T	5151	X136 – Differential lock switch	Signal error
T	5153	X6 – Differential lock solenoid valve	Control error
T	5154	X66 – Left-hand brake pedal sensor	Signal error
T	5555	X67 – Right-hand brake pedal sensor	Signal error

PTO error codes

No.	Components concerned	Causes
T	6101	X128 – Rear PTO ON/OFF switch	Signal error
T	6103	X94 – PTO ON/OFF switch on left-hand fender	Signal error
T	6104	X7 – Rear PTO solenoid valve	Control error
T	6105	X15 – PTO clutch speed sensor	Signal error
T	6110	X16 – PTO shaft speed sensor	Signal error
T	6111	X118 – Automatic PTO switch	Signal error
T	6113	X16 – PTO shaft speed sensor	Overspeed
T	6115	X145 – PTO/linkage console	Signal error
T	6116	X145 – PTO/linkage console	Signal error
T	6117	X145 – PTO/linkage console	Signal error
T	6118	X145 – PTO/linkage console	Signal error
T	611A	X3 – 540 rpm PTO speed solenoid valve	Control error
T	611B	X3 – 540 rpm PTO speed solenoid valve	Control error
T	611C	X4 – 1000 rpm PTO speed solenoid valve	Control error
T	6141	X128 – Rear PTO ON/OFF switch	Pressed down for over 30 seconds, mechanical or electrical error on switch
T	6143	X94 – PTO ON/OFF switch on left-hand fender	Pressed down for over 30 seconds, mechanical or electrical error on switch

No.	Components concerned	Causes
T	6145	X15 – PTO clutch speed sensor	NEUTRAL speed selection, PTO not activated, X15 displays a speed, the clutch disc does not separate, PTO brake does not engage selected speed, PTO clutch 100% engaged, over 20% difference between PTO clutch speed and engine speed. PTO clutch disc slips: clutch slippage. PTO clutch speed is lower than output shaft speed, X15 sensor supply voltage error.
T	6150	X16 – PTO shaft speed sensor	The PTO shaft speed is higher than 1300 rpm, signal error (X16 or X15). The selected speed is lower than the PTO output shaft speed, X16 sensor supply volt- age error, speed solenoid valve (X4, X3) locked in “de- activated” position.
T	6155	X145 – PTO/linkage console	Pressed down for over 30 seconds, mechanical or electrical error on switch
T	6156	X145 – PTO/linkage console	Pressed down for over 30 seconds, mechanical or electrical error on switch
T	6157	X145 – PTO/linkage console	Pressed down for over 30 seconds, mechanical or electrical error on switch
T	6158	X145 – PTO/linkage console	Pressed down for over 30 seconds, mechanical or electrical error on switch
T	6160	X15 – PTO clutch speed sensor	Difference of at least 12% between the output shaft speed and PTO clutch speed, speed solenoid valve (X4, X3) incorrectly connected or seized up. Mechan- ical fault with speed selection. Signal error to sen- sors (X15, X16)
X16 – PTO shaft speed sensor
T	61A1	X128 – Rear PTO ON/OFF switch	Communication error
T	61B0	X128 – Rear PTO ON/OFF switch	Initialisation error
T	61B5	X145 – PTO/linkage console	Communication error
T	61B6	X145 – PTO/linkage console	Communication error
T	61B7	X145 – PTO/linkage console	Communication error
T	61B8	X145 – PTO/linkage console	Communication error
T	61E0	X174 – Autotronic 4 transmission controller	Faulty programming
T	61E1	X174 – Autotronic 4 transmission controller	Faulty programming

Lights error codes

No.	Components concerned	Causes
L	6	X149 – Headlights module (black connector)	One or more bulb(s) missing
X305 – Headlights module (grey connector)
L	7	X149 – Headlights module (black connector)	No connection with the keypad
X305 – Headlights module (grey connector)
L	8	X149 – Headlights module (black connector)	EEPROM checksum
X305 – Headlights module (grey connector)
L	9	X149 – Headlights module (black connector)	CAN connection problem
X305 – Headlights module (grey connector)

ParkLock error codes

No.	Components concerned	Causes
P	131	X38 – Trailer braking proportional solenoid valve	Open circuit
P	132	Short circuit to earth (-)
P	133	Short circuit to +12 V

No.	Components concerned	Causes
P	141	X39 – Trailer braking safety solenoid valve	Open circuit
P	142	Short circuit to earth (-)
P	143	Short circuit to +12 V
P	151	X37 – ParkLock pressure reversing solenoid valve	Open circuit
P	152	Short circuit to earth (-)
P	153	Short circuit to +12 V
P	171	X135 – Braking pressure sensor	Signal error
P	172	X35 – ParkLock hydraulic system pressure sensor	Signal error
P	173	X21 – ParkLock brake pressure sensor	Signal error

Suspended front axle error codes

No.	Components concerned	Causes
FA	211	X178 – ParkLock/suspended front axle/passive sus- pended cab Autotronic 5	Calibration fault
FA	221	X166 – Suspended front axle position sensor	Sensor value too high
FA	222	Sensor value too low
FA	224	Calibration too low
FA	225	Calibration too high
FA	231	X154 – Suspended front axle lifting solenoid valve	Open circuit
FA	232	Short circuit to +12 V
FA	233	Short circuit to earth (-)
FA	234	X159 – Suspended front axle lowering solenoid valve	Open circuit
FA	235	Short circuit to +12 V
FA	236	Short circuit to earth (-)
FA	237	X161 – Solenoid valve 1 for suspended front axle suspension	Open circuit
FA	238	Short circuit to +12 V
FA	239	Short circuit to earth (-)
FA	241	X139 – Suspended front axle switch	Short circuit

Linkage error codes

No.	Components concerned	Causes
R	11	X27 – Rear linkage lifting solenoid valve	Open circuit
X28 – Rear linkage lowering solenoid valve
R	12	X27 – Rear linkage lifting solenoid valve	Short circuit
R	13	X28 – Rear linkage lowering solenoid valve	Short circuit
R	14	X174 – Autotronic 4 transmission controller	No CAN unlocking signal
R	15	X87 – Linkage lifting/lowering switch on right-hand fender	Incorrect signal
X97 – Linkage lifting/lowering switch on left-hand fender
R	16	X177 – Autotronic 5 Linkage	Battery voltage <11 V or >16 V
R	17	Checksum error
R	18	X119 – Rear linkage lifting/lowering switch	Incorrect signal
R	19	X177 – Autotronic 5 Linkage	Parameter loss
R	22	X30 – Rear linkage position sensor	Incorrect signal
R	23	X121 – Rear linkage height/depth adjustment thumb wheel	Incorrect signal
R	24	X145 – PTO/linkage console	Incorrect signal

No.	Components concerned	Causes
R	31	X32 – Rear linkage left-hand draft sensor	Incorrect signal
R	32	X31 – Rear linkage right-hand draft sensor	Incorrect signal
R	33	Front linkage suspension sensor	Signal incorrect or incorrect calibration
R	34	X145 – PTO/linkage console	Incorrect signal
R	35	X145 – PTO/linkage console	Incorrect signal
R	36	X145 – PTO/linkage console	Incorrect signal
R	41	X32 – Rear linkage left-hand draft sensor	Saturation
R	42	X31 – Rear linkage right-hand draft sensor	Saturation

Suspended cab error codes

No.	Components concerned	Causes
C	21	X261 – Front right-hand unit for suspended cab	Open circuit
C	22	Short circuit to +12 V
C	23	Short circuit to earth (-)
C	24	X262 – Front left-hand unit for suspended cab	Open circuit
C	25	Short circuit to +12 V
C	26	Short circuit to earth (-)
C	27	X50 – Suspended cab front lowering solenoid valve	Open circuit
C	28	Short circuit to +12 V
C	29	Short circuit to earth (-)
C	30	X49 – Suspended cab rear lowering solenoid valve	Open circuit
C	31	Short circuit to +12 V
C	32	Short circuit to earth (-)
C	33	X48 – Rear left-hand unit for suspended cab	Open circuit
C	34	Short circuit to +12 V
C	35	Short circuit to earth (-)
C	36	X47 – Rear right-hand unit for suspended cab	Open circuit
C	37	Short circuit to +12 V
C	38	Short circuit to earth (-)
C	39	X54 – Suspended cab lifting solenoid valve	Open circuit
C	40	Short circuit to +12 V
C	41	Short circuit to earth (-)
C	42	X48 – Rear left-hand position sensor	Range error
C	43	X262 – Front left-hand position sensor	Range error
C	44	X47 – Rear right-hand position sensor	Range error
C	45	X261 – Front right-hand position sensor	Range error

Armrest error codes

No.	Components concerned	Causes
AR	01	X104 – Armrest Autotronic 5	10 V output fault
AR	02	X104 – Armrest Autotronic 5	VIN Error – Vehicle electronic identification incorrect
AR	11	X307 – FingerTIP 1	Short circuit 0 V
AR	12	Short circuit to 12 V
AR	21	X308 – FingerTIP 2	Short circuit 0 V
AR	22	Short circuit to 12 V
AR	31	X108 – FingerTIP 3	Short circuit 0 V
AR	32	Short circuit to 12 V

No.	Components concerned	Causes
AR	41	X109 – FingerTIP 4	Short circuit 0 V
AR	42	Short circuit to 12 V
AR	51	X110 – FingerTIP 5	Short circuit 0 V
AR	52	Short circuit to 12 V
AR	61	X130 – FingerTIP 6 front linkage function	Short circuit 0 V
AR	62	Short circuit to 12 V
AR	71	X122 – Hand throttle	Short circuit 0 V
AR	72	Short circuit to 12 V
AR	81	X121 – Rear linkage height/depth adjustment thumb wheel	Short circuit 0 V
AR	82	Short circuit to 12 V
AR	91	X106 – Transmission lever in armrest	Short circuit 0 V
AR	92	Short circuit to 12 V

Источник

Massey Ferguson logo

MASSEY FERGUSON Tractor Fault Codes DTC

E91 Throttle Position Sensor Malfunction dampers. Contact your dealer.
E94 Fuel Filter Pressure Check fuel level in tank. Check for damage fuel lines.
Check filter status. (date of last technical service).
Check the electrical condition fuel primer pump (check fuse).
Contact your dealer.
E97 Water in fuel. Check for water in sump. fuel system. Contact your dealer.
E100 Oil pressure Check oil level. Contact your dealer.
E102 Boost pressure Check air condition filter. Contact your dealer.
E105 Intake manifold temperature Check the condition of the radiators.
Check the condition of the vent lattices. Contact your dealer.
E107 Air filter pressure Check air condition filter. Contact your dealer.
E110 Coolant temperature Check coolant level fluid. Check the condition of the vent lattices. Check the condition of the radiator. Contact your dealer.
E157 Fuel rail pressure Contact dealer.
E168 Battery voltage Check battery connections. Contact your dealer.
E174 Fuel temperature Contact your dealer.
E175 Engine oil temperature Check coolant level fluid. Check condition radiator. Contact your dealer.
E190 Engine speed signal Contact your dealer.
E626 Heater air supply control Contact your dealer.
E629 Error EEPROM Contact Dealer.
E898 Required speed out of range. Contact your dealer.
E1136 ECU temperature sensor malfunction. Contact your dealer.
E1378 Engine oil change: too big time interval. Contact your dealer.
E9006 Defective Tractor CAN-bus. Contact dealer.
E9008 ID CAN module defective. Contact your dealer.
E9010 External Pressure Contact Dealer.
E9021 DC 5 V power failure Contact your dealer.
E9022 DC 5 V power failure Contact your dealer.
E9023 DC 5 V power failure Contact your dealer.
E9024 Water in fuel sensor. Contact dealer.
E9025 Self-diagnosis shutdown lines. Contact your dealer.
E9026 Self-diagnosis shutdown lines. Contact your dealer.
E9027 Self-diagnosis shutdown lines. Contact your dealer.
E9030 Short circuit in the main relay 1 ECU. Contact your dealer.
E9031 Short circuit in the main relay 2 ECU Contact dealer.
E9032 Short circuit in the main relay 3 ECU Contact dealer.
E9033 The ECU shutdown function is faulty. Contact your dealer.
E9034 Disable ECU function did not work in the previous time. Contact your dealer.
E9035 Normal Health Recovery Contact your dealer.
E9036 Full reboot after 2 seconds after 3 operations recovery. Contact your dealer.
E9070 Crankshaft Speed Signal Contact your dealer.
E9071 Crankshaft Speed Signal Contact your dealer.
E9072 Crankshaft Speed Sensor Contact your dealer.
E9080 Camshaft Speed Sensor Contact your dealer.
E9081 Camshaft Speed Sensor Contact your dealer.
E9082 Camshaft Speed Sensor Contact your dealer.
E9083 Camshaft Speed Sensor Contact your dealer.
E9090 Error estimating engine speed signal Contact dealer.
E9100 Security update error Contact dealer.
E9107 Wrong selection of computer address. Contact your dealer.
E9131 Fuel injector no. 1 malfunction. Contact your dealer.
E9132 Fuel injector no. 2 malfunction. Contact your dealer.
E9133 Fuel injector no. 3 malfunction. Contact your dealer.
E9134 Fuel injector no. 4 malfunction. Contact your dealer.
E9135 Fuel injector no. 5 malfunction. Contact your dealer.
E9136 Fuel injector no. 6 malfunction. Contact your dealer.
E9150 Fuel rail pressure Contact dealer.
E9151 Fuel rail pressure limiter Contact a dealer.
E9152 Fuel Filter Pressure Check fuel level in tank. Check for damage fuel lines. Contact your dealer.
E9153 Fuel Filter Pressure Check fuel level in tank. Check for damage fuel lines. Contact your dealer.
E9170 Fuel pump control (ECU). Contact your dealer.
E9171 Preheating Device Control. Contact your dealer.
E9172 Starter Relay Control Contact your dealer.
E9173 Starter Relay Control Contact your dealer.
E9174 MPROP Pump Control Contact your dealer.
E9230 Engine specification mismatch. Contact your dealer.
E9231 Engine serial number mismatch. Contact dealer.
E9233 ID Module Contact your dealer.
E9234 ID Module Contact your dealer.
E9235 ID Module Contact your dealer.
E9236 Module ID.

U 168 Battery voltage. Contact dealer.
U 441 – U 442 – U 697. Catalyst temperature Contact your dealer.
U 698 Power Supply Exhaust Pipe Contact your dealer.
U 699 Power Supply Intake Pipe Contact Dealer.
U 700 Power supply for heating flow line. Contact dealer.
U 1079 Sensor 1 supply voltage. Contact your dealer.
U 1080 Sensor Supply Voltage 2 Contact your dealer.
U 1387 Urea Pressure Contact Dealer.
U 1388 Urea Pressure Sensor Contact your dealer.
U 1485 Main Relay Contact your dealer.
U 1677 Modular Heater Contact a dealer.
U 1761 Level sensor in urea container Contact your dealer.
U 2854 – U 2858 CAN Receiver Contact your dealer.
U 2859 Urea / heater or measurement state exhaust. Contact your dealer.
U 2860 – U 2871 CAN Message Contact your dealer.
U 2872 Error turning on heater or unit data management. Contact your dealer.
U 3031 Urea Container Temperature Sensor Contact your dealer.
U 520201 Power module temperature Contact a dealer.
U 520228 NOx emission control Contact your dealer.
U 520239 Heater Power Contact your dealer.
U 520243 Urea level. Contact dealer.
U 520257 Urea leak. Contact your dealer.
U 520260 Urea Pressure Contact your dealer.
U 520276 Power Supply Voltage Contact Dealer.
U 520296 NOx control unit. Contact your dealer.
U 520308 NOx Sensor Contact your dealer.
U 520310 Temperature in the urea tank. Contact your dealer.

Источник

Здарова мужики. Трактор Massey Ferguson 6713 выдает на панели ошибку, подскажите чо такое?

Трактор Massey Ferguson 6713 Ошибка

Похожие посты

Какой трактор нужен для работы на склоне до 25 градусов?

Автор: Сергей Смирнов
05 сентября 22:10
8 комментариев

Всем привет! Какой трактор нужен для работы на склоне до 25 градусов? Подскажите, пожалуйста, какая техника понадобится для заготовки сена в рулоны на склоне до 25 градусов. На фото выглядит не очень страшно, в реальности высоко и круто… Я правильно понимаю, что тут только 4 ведущих колеса и минимум что-то вроде МТЗ 82?

Какой Трактор Нужен Работа склон 25 градус

Источник

Fault codes

In the event of a malfunction, all codes can be viewed using the Instrument Panel Control Unit on the instrument cluster.

System fault E3 engine with AdBlue / DEF technology

If a malfunction occurs in the system, an error code appears on the dashboard corresponding to the malfunction.

Emergency operation is activated, in which the engine power is limited to 60%, and the maximum speed is 1500 rpm.

System errors
GPI Error No.	Checked signal from	Type of Error	Error LED flash code	DIA 1 Error No.	Error caused by
1	sensor supply voltage	4	– • • •	01	sensor voltage out of range
2 — 16	not used
Sensor errors
GPI Error No.	Checked signal from	Type of Error	Error LED flash code	DIA 1 Error No.	Error caused by
1	default parameter checksum	3	––––––	17	checksum mismatch
2	inch parameter checksum	18	included default checksum
3	inch/brake potentiometer	7 5 6	– – • •	19	no pedal setup done value too low value too high
4	engine speed pickup	6	• • – •	20	engine speed missed when starting engine
5	propel current	1 2	– • – •	21	short cut open circuit
6	F-N-R switch	4	• – – •	22	short cut between forward and reverse
7	engine speed pickup	6	– – – •	23	engine speed interrupted
8	hydro motor propel current	1 2	• • • –	24	short cut open circuit
9	creep drive parameter checksum	25	included default checksum
10	creep drive potentiometer	5 6	– • • –	26	value too low value too high
11	motor speed pickup	6	• • – –	27	motor speed interrupted
12 — 32	not used
—	wrong kernel	—	• – • –	kernel software < 2.5
—	wrong hardware	—	– – • –	hardware is not S1X-11 G2 AMP

Models 8600 8650-8660-8670-8680-8690 Fault Codes

8450 — 8460 — 8470 — 8480

code	Description	Solution
D101	Armrest connection not detected	Check the connection under the vile boiler
D121	Generator regulator	Please contact your dealer.
D122	Generator regulator	Please contact your dealer.
D127	Fuel gauge	Please contact your dealer.
D128	Fuel gauge	Please contact your dealer.
D129	Too high voltage battery baht yards	Please contact your dealer.
D130	Battery voltage too low bata peu	Make sure the battery terminals are secure and free from dirt. Please contact your dealer.
D133	Accelerator Pedal Potentiometer	Please contact your dealer.
D134	Accelerator Pedal Potentiometer	Please contact your dealer.
D135	Power Control Controller	Please contact your dealer.
D136	Power Control Controller	Please contact your dealer.
D137	Armrest Lever Potentiometer	Please contact your dealer.
D138	Armrest Lever Potentiometer	Please contact your dealer.
D139	Clutch pedal	Please contact your dealer.
D140	Clutch pedal	Please contact your dealer.
D141	Engine speed signal	Please contact your dealer.
D142	High clutch point sensor	Please contact your dealer.
D143	Low clutch point sensor	Please contact your dealer.
D144	Power Control Controller	Please contact your dealer.
D145	Power Control Controller	Please contact your dealer.
D146	Power Control Controller	Please contact your dealer.
D147	Power Control Controller	Please contact your dealer.
D148	dashboard	Please contact your dealer.
D149	CAN bus signals	Please contact your dealer.
D150	CAN bus signals	Please contact your dealer.
D151	Tractor speed too high	Please contact your dealer.
D152	dashboard	Please contact your dealer.
D153	dashboard	Please contact your dealer.
D154	Autotronic 4 CAN bus communication with instrument panel	Please contact your dealer.
D155	dashboard	Please contact your dealer.
D156	High clutch point sensor	Please contact your dealer.
D157	Engine speed sensor	Please contact your dealer.
D158	Armrest Lever Potentiometer	Please contact your dealer.
D159	Power Control Controller	Please contact your dealer.
D160	Power Control Controller	Please contact your dealer.
D164	Communication error on the CAN bus of the EEM system with the instrument panel	Please contact your dealer.
D170	Throttle grip	Please contact your dealer.
D181	Auxiliary Hydraulic Lever	Please contact your dealer.
D182	Auxiliary Hydraulic Lever	Please contact your dealer.
D183	Wheel Angle Sensor	Please contact your dealer.
D184	Wheel Angle Sensor	Please contact your dealer.
D185	Keyboard	Please contact your dealer.
D186	Keyboard	Please contact your dealer.
D189	Output voltage 9.5V	Please contact your dealer.
D190	Output voltage 9.5V	Please contact your dealer.
D191	Air pressure sensor	Please contact your dealer.
D192	Air pressure sensor	Please contact your dealer.
D193	Steering gear ratio quick change potentiometer	Please contact your dealer.
D194	Steering gear ratio quick change potentiometer	Please contact your dealer.
D195	Internal temperature sensor instrument panel	Please contact your dealer.
D196	Internal temperature sensor instrument panel	Please contact your dealer.
D197	Auxiliary Hydraulic Oil Temperature Gauge	Please contact your dealer.
D198	Auxiliary Hydraulic Oil Temperature Gauge	Please contact your dealer.

code	Description	Solution
E91	Malfunction of throttle position sensor flap	Please contact your dealer.
E94	Fuel filter pressure	Check the fuel level in the tank. Check the fuel lines for damage. Check the condition of the filter (date of last service). Check the electrical fuel priming pump is working (check the fuse). Please contact your dealer.
E97	Water in fuel	Check for water in the fuel system sump. Please contact your dealer.
E100	Oil pressure	Check the oil level. Please contact your dealer.
E102	Boost pressure	Check the condition of the air filter. Check the condition of the suction hoses. Please contact your dealer.
E105	Intake Manifold Temperature	Check the condition of the radiators. Check the condition of the ventilation grilles. Please contact your dealer.
E107	Air filter pressure	Check the condition of the air filter. Please contact your dealer.
E110	Coolant temperature	Check the coolant level . Check the condition of the ventilation grilles. Check the condition of the radiator. Please contact your dealer.
E157	Fuel rail pressure	Please contact your dealer.
E168	Battery voltage	Check battery connections. Please contact your dealer.
E174	Fuel temperature	Please contact your dealer.
E175	Engine oil temperature	Check the coolant level . Check the condition of the radiator. Please contact your dealer.
E190	Engine speed signal	Please contact your dealer.
E626	Heater air control	Please contact your dealer.
E629	EEPROM error	Please contact your dealer.
E898	Required speed out of range	Please contact your dealer.
E1136	ECU temperature sensor malfunction	Please contact your dealer.
E1378	Changing the engine oil: too long time has elapsed	Please contact your dealer.
E9006	Faulty CAN-bus of the tractor	Please contact your dealer.
E9008	Defective CAN ID module	Please contact your dealer.
E9010	External pressure	Please contact your dealer.
E9021	Failure of 5V DC power supply	Please contact your dealer.
E9022	Failure of 5V DC power supply	Please contact your dealer.
E9023	Failure of 5V DC power supply	Please contact your dealer.
E9024	Water in fuel sensor	Please contact your dealer.
E9025	Self-test disconnect lines	Please contact your dealer.
E9026	Self-test disconnect lines	Please contact your dealer.
E9027	Self-test disconnect lines	Please contact your dealer.
E9030	Short circuit in the main relay 1 ECU	Please contact your dealer.
E9031	Short circuit in the main relay 2 ECU	Please contact your dealer.
E9032	Short circuit in the main relay 3 ECU	Please contact your dealer.
E9033	Defective ECU shutdown function	Please contact your dealer.
E9034	ECU shutdown function did not work the previous time	Please contact your dealer.
E9035	Normal recovery of performance	Please contact your dealer.
E9036	Full reboot in 2 seconds after 3 restore operations	Please contact your dealer.
E9070	Engine speed signal	Please contact your dealer.
E9071	Engine speed signal	Please contact your dealer.
E9072	Crankshaft speed sensor	Please contact your dealer.

E9080	Camshaft speed sensor	Please contact your dealer.
E9081	Camshaft speed sensor	Please contact your dealer.
E9082	Camshaft speed sensor	Please contact your dealer.
E9083	Camshaft speed sensor	Please contact your dealer.
E9090	Engine speed signal estimation error	Please contact your dealer.
E9100	Protection update error	Please contact your dealer.
E9107	Incorrect ECU address selection	Please contact your dealer.
E9131	Malfunction of the fuel injector No. 1	Please contact your dealer.
E9132	Malfunction of the fuel injector No. 2	Please contact your dealer.
E9133	Malfunction of the fuel injector No. 3	Please contact your dealer.
E9134	Malfunction of the fuel injector No. 4	Please contact your dealer.
E9135	Malfunction of the fuel injector No. 5	Please contact your dealer.
E9136	Malfunction of the fuel injector No. 6	Please contact your dealer.
E9150	Fuel rail pressure	Please contact your dealer.
E9151	Fuel rail pressure limiter	Please contact your dealer.
E9152	Fuel filter pressure	Check the fuel level in the tank. Check the fuel lines for damage. Please contact your dealer.
E9153	Fuel filter pressure	Check the fuel level in the tank. Check the fuel lines for damage. Please contact your dealer.
E9170	Fuel priming pump control (ECU)	Please contact your dealer.
E9171	Preheating device control	Please contact your dealer.
E9172	Starter relay control	Please contact your dealer.
E9173	Starter relay control	Please contact your dealer.
E9174	MPROP pump control	Please contact your dealer.
E9230	Inconsistency of technical characteristics of the engine	Please contact your dealer.
E9231	Engine Serial Number Mismatch	Please contact your dealer.
E9233	Module ID	Please contact your dealer.
E9234	Module ID	Please contact your dealer.
E9235	Module ID	Please contact your dealer.
E9236	Module ID	Please contact your dealer.
E9237	Module ID	Please contact your dealer.
E9238	Module ID	Please contact your dealer.
E9239	Module ID	Please contact your dealer.
E9240	Module ID	Please contact your dealer.
E9241	Module ID	Please contact your dealer.
E9242	The generated traversal time has elapsed	Please contact your dealer.
E9243	The maximum time for bypassing the computer has elapsed	Please contact your dealer.
E9244	Module ID	Please contact your dealer.
E9303	Malfunctioning cruise control	Please contact your dealer.
E9304	There is no data on the speed of the tractor	Please contact your dealer.
E9305	Incorrect digital input configuration	Please contact your dealer.
E9306	PTO input signal error	Please contact your dealer.
E9310	Fault external digital input	Please contact your dealer.
E9311	Fault external digital input	Please contact your dealer.
E9312	Torque control input	Please contact your dealer.
E9317	Data manager missing	Please contact your dealer.

U 168	Battery voltage	Please contact your dealer.
U 441 — U 442 — U 697	Catalyst temperature	Please contact your dealer.
U 698	Discharge heating power supply	Please contact your dealer.
U 699	Intake manifold heating power supply	Please contact your dealer.
U 700	Heating supply of the pressure pipeline	Please contact your dealer.
U 1079	Sensor supply voltage 1	Please contact your dealer.
U 1080	Sensor supply voltage 2	Please contact your dealer.
U 1387	Urea pressure	Please contact your dealer.
U 1388	Urea pressure sensor	Please contact your dealer.
U 1485	Main relay	Please contact your dealer.
U 1677	Modular heater	Please contact your dealer.
U 1761	Level sensor in urea tank	Please contact your dealer.
U 2854 — U 2858	CAN receiver	Please contact your dealer.
U 2859	Urea / Heater or Exhaust Measurement State	Please contact your dealer.
U 2860 — U 2871	CAN message	Please contact your dealer.
U 2872	Error turning on the heater or data control unit	Please contact your dealer.
U 3031	Temperature sensor in urea tank	Please contact your dealer.
U 520201	Power module temperature	Please contact your dealer.
U 520228	NOx emission control	Please contact your dealer.
U 520239	Heater power supply	Please contact your dealer.
U 520243	Urea level	Please contact your dealer.
U 520257	Leakage of urea	Please contact your dealer.
U 520260	Urea pressure	Please contact your dealer.
U 520276	Power supply voltage	Please contact your dealer.
U 520296	NOx control unit	Please contact your dealer.
U 520308	NOx sensor	Please contact your dealer.
U 520310	Temperature in the urea tank	Please contact your dealer.

T4107	Transmission oil high pressure sensor malfunction	Please contact your dealer.
T4108	Included range sensor malfunction	Please contact your dealer.
T4124	Parking brake sensor malfunction	Please contact your dealer.
T4128	Transmission control unit malfunction	Use the transmission protection mode. Please contact your dealer.
T412A	Malfunction of the sensor of the estimated gear speed	Use the transmission protection mode. Please contact your dealer.
T412B	Malfunction of the switch of ranges of high / low speeds («Hare» / «Turtle»)	Please contact your dealer.
T4131	Malfunction of the summing shaft speed sensor	Use the transmission protection mode . Please contact your dealer.
T4142	Malfunction of the summing shaft speed sensor	Use the transmission protection mode. Please contact your dealer.
T4144	Malfunction of the engine speed sensor	Use the transmission protection mode. Please contact your dealer.
T4145	Malfunction of the sensor of the estimated gear speed	Use the transmission protection mode. Please contact your dealer.
T4150	Transmission filter clogging sensor malfunction	Please contact your dealer.
T4153	High transmission oil temperature	Further movement is prohibited. Please contact your dealer.
T4156	Transmission filter clogging sensor malfunction	Please contact your dealer.
T4158	Transmission slip sensor malfunction	Please contact your dealer.
T4159	Malfunction of turning on the transmission protection mode or an error in this mode	Please contact your dealer.
T4161	Malfunction of the solenoid valve of the low speed range («Turtle»)	Use the transmission protection mode. Please contact your dealer.
T4162	High speed range solenoid valve malfunction («Hare»)	Use the transmission protection mode. Please contact your dealer.
T4163	Malfunction of the solenoid valve for speed limiting up to 30 km / h	Please contact your dealer.
T4164	Defective clutch solenoid valve	Please contact your dealer.
T4172	Transmission filter clogging sensor malfunction	Please contact your dealer.
T4173	Transmission oil temperature sensor malfunction	Please contact your dealer.
T4174	Parking brake sensor malfunction	Please contact your dealer.
T4182	Malfunction of the calculated gear speed sensor Malfunction of the summing shaft speed sensor	Use the transmission protection mode. Please contact your dealer.
T4183	Malfunction of the calculated gear speed sensor Malfunction of the summing shaft speed sensor	Use the transmission protection mode. Please contact your dealer.
T4192	Malfunction of the switch of the right brake	Please contact your dealer.
T4193	Left Brake Switch Malfunction	Please contact your dealer.
T41A0	Transmission control unit malfunction	Please contact your dealer.
T41A1	Transmission control unit malfunction	Please contact your dealer.
T41A2	Transmission control unit malfunction	Please contact your dealer.
T41A3	Transmission control unit malfunction	Please contact your dealer.
T41A4	Transmission control unit malfunction	Please contact your dealer.
T41A5	Transmission control unit malfunction	Please contact your dealer.
T41A6	Transmission control unit malfunction	Please contact your dealer.
T41B0	CAN bus malfunction	Please contact your dealer.
T41B1	Malfunction of the solenoid valve of the low speed range («Turtle»)	Please contact your dealer.
T41B2	High speed range solenoid valve malfunction («Hare»)	Please contact your dealer.
T41C1	Engine stalled due to transmission overload	Reduce the load on the transmissions and try again. Please contact your dealer.
T41D1	Calibration error	Please contact your dealer.
T41D2	Calibration error	Please contact your dealer.
T41D3	Calibration error	Please contact your dealer.
T41D4	Calibration error	Please contact your dealer.
T41D5	Calibration error	Please contact your dealer.
T41D6	Calibration error	Please contact your dealer.
T41D7	Calibration error	Please contact your dealer.
T41D8	Calibration error	Please contact your dealer.
T41D9	Calibration error	Please contact your dealer.
T41DA	Calibration error	Please contact your dealer.
T41DB	Calibration error	Please contact your dealer.
T41DC	Calibration error	Please contact your dealer.
T41DD	Calibration error	Please contact your dealer.
T41DE	Calibration error	Please contact your dealer.
T41DF	Calibration error	Please contact your dealer.
T41 E0	Defective clutch solenoid valve	Please contact your dealer.
T41EB	Included range sensor malfunction	Use the transmission protection mode. Please contact your dealer.
T41EE	The curve of transmission parameters in the program	Use the transmission protection mode. Please contact your dealer.
T41EF	Coupling curve in the program	Please contact your dealer.
T41FF	Malfunction Autotronic 4	Please contact your dealer.

code	Description	Solution
T5131	4WD switch malfunction	Please contact your dealer.
T5132	4WD switch malfunction	Please contact your dealer.
T5133	Fault full electromagnetic valve actuator	Please contact your dealer.
T5151	Differential lock switch malfunction	Please contact your dealer.
T5153	Differential lock solenoid valve malfunction	Please contact your dealer.
T5154	Left Brake Switch Malfunction	Please contact your dealer.
T5155	Malfunction of the switch of the right brake	Please contact your dealer.
T51FF	Malfunction Autotronic 4	Please contact your dealer.

T6101	Faulty PTO ON / OFF switch	Please contact your dealer.
T6102	Malfunction of the PTO ON / OFF switch located on the wing	Please contact your dealer.
T6104	Malfunction of the PTO solenoid valve	Please contact your dealer.
T6105	Malfunction of the PTO clutch speed sensor	Please contact your dealer.
T6110	Malfunction of the PTO shaft speed sensor	Please contact your dealer.
T6115	Malfunction of the neutral switch on the PTO control unit	Please contact your dealer.
T6116	Malfunction of the switch of the speed range of 540 rpm on the PTO control unit	Please contact your dealer.
T6117	Malfunction of the ECO speed range switch on the PTO control unit	Please contact your dealer.
T6118	Malfunction of the switch of the speed range of 1000 rpm on the PTO control unit	Please contact your dealer.
T611A	Malfunction of the solenoid valve of the speed range of 540 rpm	Please contact your dealer.
T611B	Malfunction of the ECO PTO speed solenoid valve	Please contact your dealer.
T611C	Malfunction of the solenoid valve of the speed range of 1000 rpm	Please contact your dealer.
T6141	Faulty PTO ON / OFF switch	Please contact your dealer.
T6143	Malfunction of the PTO ON / OFF switch located on the wing	Please contact your dealer.
T6145	Malfunction of the PTO clutch speed sensor	Please contact your dealer.
T6150	Malfunction of the PTO shaft speed sensor	Please contact your dealer.
T6155	Malfunction of the neutral switch on the PTO control unit	Please contact your dealer.
T6156	Malfunction of the switch of the speed range of 540 rpm on the PTO control unit	Please contact your dealer.
T6157	Malfunction of the ECO speed range switch on the PTO control unit	Please contact your dealer.
T6158	Malfunction of the switch of the speed range of 1000 rpm on the PTO control unit	Please contact your dealer.
T6160	Malfunction of the PTO shaft speed sensor Malfunction of the PTO clutch speed sensor	Please contact your dealer.
T61A1	Faulty PTO ON / OFF switch	Please contact your dealer.
T61B5	Malfunction of the neutral switch on the PTO control unit	Please contact your dealer.
T61B6	Malfunction of the switch of the speed range of 540 rpm on the PTO control unit	Please contact your dealer.
T61B7	Malfunction of the ECO speed range switch on the PTO control unit	Please contact your dealer.
T61B8	Malfunction of the switch of the speed range of 1000 rpm on the PTO control unit	Please contact your dealer.

Hydraulic valve error codes

T011493

Reading the error code number.

The code consists of a letter and three numbers.

For example V149:

— V = hydraulic valve

— 1 = number of faulty valve

— 49 = error code number

code	Description	Consequences	Solution
V.43	Malfunction of the valve position sensor line	— When an error code appears , a «beep» is heard. — Error code on the display Instrument panel control unit — All valves locked	— Delete the error code from the control unit of the instrument panel — Unlock the valves (the valve affected by the error code remains blocked). — To reactivate the valve affected by the error code , stop and restart the engine. If the error code is still present, the valve affected by the error code remains blocked. — Contact your dealer.
V.49	Main valve does not return to neutral position	— No — Error code on the display Instrument panel control unit	— Delete error code from Instrument panel control unit — Contact your dealer.
V.52	When starting, the main valve is not in neutral	— No — Error code on the display Instrument panel control unit	— Delete error code from Instrument panel control unit — Contact your dealer.

Press the button (16) to clear the error code on the instrument panel control unit display. on keyboard

01	Output signal error 10 V. Autotronic armrest 5.	Please contact your dealer.
eleven	FingerTIP 1 — short circuit to 0 V.	Please contact your dealer.
12	FingerTIP 1 — short circuit to 12V.	Please contact your dealer.
21	FingerTIP 2 — short circuit to 0 V.	Please contact your dealer.
22	FingerTIP 2 — short circuit to 12V.	Please contact your dealer.
31	FingerTIP 3 — short circuit to 0 V.	Please contact your dealer.
32	FingerTIP 3 — short circuit to 12V.	Please contact your dealer.
41	FingerTIP 4 — short circuit to 0 V.	Please contact your dealer.
42	FingerTIP 4 — short circuit to 12V.	Please contact your dealer.
51	FingerTIP 5 — short circuit to 0 V.	Please contact your dealer.
52	FingerTIP 5 — short circuit to 12V.	Please contact your dealer.
61	FingerTIP 6 — short circuit to 0 V.	Please contact your dealer.
62	FingerTIP 6 — short circuit to 12V.	Please contact your dealer.
71	Throttle position control handle — short circuit to 0 V.	Please contact your dealer.
72	Throttle position control handle — short circuit to 12V.	Please contact your dealer.
81	Rear linkage height adjusting wheel — short circuit to 0 V.	Please contact your dealer.
82	Rear linkage height adjusting wheel — short circuit to 12V.	Please contact your dealer.
91	Transmission lever — short circuit to 0 V.	Please contact your dealer.
92	Transmission lever — short circuit to 12V.	Please contact your dealer.
6	One or more indicator lights are missing	Install indicator bulbs where they are missing.
7	Keyboard not connected	Please contact your dealer.
eight	Checksum error	Please contact your dealer.
9	CAN communication problem	Please contact your dealer.
10	Short circuit in the front roof lights	Please contact your dealer.
eleven	Short circuit in the tail lights on the roof	Please contact your dealer.
12	Short circuit in brake lights	Please contact your dealer.
thirteen	Reversing light short circuit	Please contact your dealer.

Источник

Service technicians have no problem recognising breakdowns and carrying out machine diagnostics, Massey Ferguson 8450-8460-8470-8480, 8600-8650-8660-8670-8680-8690 Fault Codes List, plus they are familiar with equipment from a variety of manufacturers.

If the electronic system detects the presence malfunction, the code is displayed on the screen faults in the form of a symbol and a letter denoting the faulty component. Under certain conditions, in addition to display of the malfunction code, the corresponding warning lamp flashes and turns on sound signal. If a malfunction occurs in the system, an error code appears on the dashboard corresponding to the malfunction. In the event of a malfunction, all codes can be viewed using the Instrument Panel Control Unit on the instrument cluster. Emergency operation is activated, in which the engine power is limited to 60%, and the maximum speed is 1500 rpm.

System fault E3 engine with AdBlue / DEF technology

Depending on the displayed fault it is recommended to perform basic operations service or contact your dealer (see fault code tables below).

Massey Ferguson MF8925 Error Code

System errors
GPI Error No.	Checked signal from	Type of Error	Error LED flash code	DIA 1 Error No.	Error caused by
1	sensor supply voltage	4	– • • •	01	sensor voltage out of range
2 – 16	not used
Sensor errors
GPI Error No.	Checked signal from	Type of Error	Error LED flash code	DIA 1 Error No.	Error caused by
1	default parameter checksum	3	––––––	17	checksum mismatch
2	inch parameter checksum	18	included default checksum
3	inch/brake potentiometer	7 5 6	– – • •	19	no pedal setup done value too low value too high
4	engine speed pickup	6	• • – •	20	engine speed missed when starting engine
5	propel current	1 2	– • – •	21	short cut open circuit
6	F-N-R switch	4	• – – •	22	short cut between forward and reverse
7	engine speed pickup	6	– – – •	23	engine speed interrupted
8	hydro motor propel current	1 2	• • • –	24	short cut open circuit
9	creep drive parameter checksum	25	included default checksum
10	creep drive potentiometer	5 6	– • • –	26	value too low value too high
11	motor speed pickup	6	• • – –	27	motor speed interrupted
12 – 32	not used
–	wrong kernel	–	• – • –	kernel software < 2.5
–	wrong hardware	–	– – • –	hardware is not S1X-11 G2 AMP

Massey Ferguson 8450-8460-8470-8480, 8600-8650-8660-8670-8680-8690 Fault Codes dashboard

code	Description	Solution
D101	Armrest connection not detected	Check the connection under the vile boiler
D121	Generator regulator	Please contact your dealer.
D122	Generator regulator	Please contact your dealer.
D127	Fuel gauge	Please contact your dealer.
D128	Fuel gauge	Please contact your dealer.
D129	Too high voltage battery baht yards	Please contact your dealer.
D130	Battery voltage too low bata peu	Make sure the battery terminals are secure and free from dirt. Please contact your dealer.
D133	Accelerator Pedal Potentiometer	Please contact your dealer.
D134	Accelerator Pedal Potentiometer	Please contact your dealer.
D135	Power Control Controller	Please contact your dealer.
D136	Power Control Controller	Please contact your dealer.
D137	Armrest Lever Potentiometer	Please contact your dealer.
D138	Armrest Lever Potentiometer	Please contact your dealer.
D139	Clutch pedal	Please contact your dealer.
D140	Clutch pedal	Please contact your dealer.
D141	Engine speed signal	Please contact your dealer.
D142	High clutch point sensor	Please contact your dealer.
D143	Low clutch point sensor	Please contact your dealer.
D144	Power Control Controller	Please contact your dealer.
D145	Power Control Controller	Please contact your dealer.
D146	Power Control Controller	Please contact your dealer.
D147	Power Control Controller	Please contact your dealer.
D148	dashboard	Please contact your dealer.
D149	CAN bus signals	Please contact your dealer.
D150	CAN bus signals	Please contact your dealer.
D151	Tractor speed too high	Please contact your dealer.
D152	dashboard	Please contact your dealer.
D153	dashboard	Please contact your dealer.
D154	Autotronic 4 CAN bus communication with instrument panel	Please contact your dealer.
D155	dashboard	Please contact your dealer.
D156	High clutch point sensor	Please contact your dealer.
D157	Engine speed sensor	Please contact your dealer.
D158	Armrest Lever Potentiometer	Please contact your dealer.
D159	Power Control Controller	Please contact your dealer.
D160	Power Control Controller	Please contact your dealer.
D164	Communication error on the CAN bus of the EEM system with the instrument panel	Please contact your dealer.
D170	Throttle grip	Please contact your dealer.
D181	Auxiliary Hydraulic Lever	Please contact your dealer.
D182	Auxiliary Hydraulic Lever	Please contact your dealer.
D183	Wheel Angle Sensor	Please contact your dealer.
D184	Wheel Angle Sensor	Please contact your dealer.
D185	Keyboard	Please contact your dealer.
D186	Keyboard	Please contact your dealer.
D189	Output voltage 9.5V	Please contact your dealer.
D190	Output voltage 9.5V	Please contact your dealer.
D191	Air pressure sensor	Please contact your dealer.
D192	Air pressure sensor	Please contact your dealer.
D193	Steering gear ratio quick change potentiometer	Please contact your dealer.
D194	Steering gear ratio quick change potentiometer	Please contact your dealer.
D195	Internal temperature sensor instrument panel	Please contact your dealer.
D196	Internal temperature sensor instrument panel	Please contact your dealer.
D197	Auxiliary Hydraulic Oil Temperature Gauge	Please contact your dealer.
D198	Auxiliary Hydraulic Oil Temperature Gauge	Please contact your dealer.

Engine error codes

code	Description	Solution
E91	Malfunction of throttle position sensor flap	Please contact your dealer.
E94	Fuel filter pressure	Check the fuel level in the tank. Check the fuel lines for damage. Check the condition of the filter (date of last service). Check the electrical fuel priming pump is working (check the fuse). Please contact your dealer.
E97	Water in fuel	Check for water in the fuel system sump. Please contact your dealer.
E100	Oil pressure	Check the oil level. Please contact your dealer.
E102	Boost pressure	Check the condition of the air filter. Check the condition of the suction hoses. Please contact your dealer.
E105	Intake Manifold Temperature	Check the condition of the radiators. Check the condition of the ventilation grilles. Please contact your dealer.
E107	Air filter pressure	Check the condition of the air filter. Please contact your dealer.
E110	Coolant temperature	Check the coolant level . Check the condition of the ventilation grilles. Check the condition of the radiator. Please contact your dealer.
E157	Fuel rail pressure	Please contact your dealer.
E168	Battery voltage	Check battery connections. Please contact your dealer.
E174	Fuel temperature	Please contact your dealer.
E175	Engine oil temperature	Check the coolant level . Check the condition of the radiator. Please contact your dealer.
E190	Engine speed signal	Please contact your dealer.
E626	Heater air control	Please contact your dealer.
E629	EEPROM error	Please contact your dealer.
E898	Required speed out of range	Please contact your dealer.
E1136	ECU temperature sensor malfunction	Please contact your dealer.
E1378	Changing the engine oil: too long time has elapsed	Please contact your dealer.
E9006	Faulty CAN-bus of the tractor	Please contact your dealer.
E9008	Defective CAN ID module	Please contact your dealer.
E9010	External pressure	Please contact your dealer.
E9021	Failure of 5V DC power supply	Please contact your dealer.
E9022	Failure of 5V DC power supply	Please contact your dealer.
E9023	Failure of 5V DC power supply	Please contact your dealer.
E9024	Water in fuel sensor	Please contact your dealer.
E9025	Self-test disconnect lines	Please contact your dealer.
E9026	Self-test disconnect lines	Please contact your dealer.
E9027	Self-test disconnect lines	Please contact your dealer.
E9030	Short circuit in the main relay 1 ECU	Please contact your dealer.
E9031	Short circuit in the main relay 2 ECU	Please contact your dealer.
E9032	Short circuit in the main relay 3 ECU	Please contact your dealer.
E9033	Defective ECU shutdown function	Please contact your dealer.
E9034	ECU shutdown function did not work the previous time	Please contact your dealer.
E9035	Normal recovery of performance	Please contact your dealer.
E9036	Full reboot in 2 seconds after 3 restore operations	Please contact your dealer.
E9070	Engine speed signal	Please contact your dealer.
E9071	Engine speed signal	Please contact your dealer.
E9072	Crankshaft speed sensor	Please contact your dealer.

E9080	Camshaft speed sensor	Please contact your dealer.
E9081	Camshaft speed sensor	Please contact your dealer.
E9082	Camshaft speed sensor	Please contact your dealer.
E9083	Camshaft speed sensor	Please contact your dealer.
E9090	Engine speed signal estimation error	Please contact your dealer.
E9100	Protection update error	Please contact your dealer.
E9107	Incorrect ECU address selection	Please contact your dealer.
E9131	Malfunction of the fuel injector No. 1	Please contact your dealer.
E9132	Malfunction of the fuel injector No. 2	Please contact your dealer.
E9133	Malfunction of the fuel injector No. 3	Please contact your dealer.
E9134	Malfunction of the fuel injector No. 4	Please contact your dealer.
E9135	Malfunction of the fuel injector No. 5	Please contact your dealer.
E9136	Malfunction of the fuel injector No. 6	Please contact your dealer.
E9150	Fuel rail pressure	Please contact your dealer.
E9151	Fuel rail pressure limiter	Please contact your dealer.
E9152	Fuel filter pressure	Check the fuel level in the tank. Check the fuel lines for damage. Please contact your dealer.
E9153	Fuel filter pressure	Check the fuel level in the tank. Check the fuel lines for damage. Please contact your dealer.
E9170	Fuel priming pump control (ECU)	Please contact your dealer.
E9171	Preheating device control	Please contact your dealer.
E9172	Starter relay control	Please contact your dealer.
E9173	Starter relay control	Please contact your dealer.
E9174	MPROP pump control	Please contact your dealer.
E9230	Inconsistency of technical characteristics of the engine	Please contact your dealer.
E9231	Engine Serial Number Mismatch	Please contact your dealer.
E9233	Module ID	Please contact your dealer.
E9234	Module ID	Please contact your dealer.
E9235	Module ID	Please contact your dealer.
E9236	Module ID	Please contact your dealer.
E9237	Module ID	Please contact your dealer.
E9238	Module ID	Please contact your dealer.
E9239	Module ID	Please contact your dealer.
E9240	Module ID	Please contact your dealer.
E9241	Module ID	Please contact your dealer.
E9242	The generated traversal time has elapsed	Please contact your dealer.
E9243	The maximum time for bypassing the computer has elapsed	Please contact your dealer.
E9244	Module ID	Please contact your dealer.
E9303	Malfunctioning cruise control	Please contact your dealer.
E9304	There is no data on the speed of the tractor	Please contact your dealer.
E9305	Incorrect digital input configuration	Please contact your dealer.
E9306	PTO input signal error	Please contact your dealer.
E9310	Fault external digital input	Please contact your dealer.
E9311	Fault external digital input	Please contact your dealer.
E9312	Torque control input	Please contact your dealer.
E9317	Data manager missing	Please contact your dealer.

E3 engine error codes with technology AdBlue / DEF

U 168	Battery voltage	Please contact your dealer.
U 441 – U 442 – U 697	Catalyst temperature	Please contact your dealer.
U 698	Discharge heating power supply	Please contact your dealer.
U 699	Intake manifold heating power supply	Please contact your dealer.
U 700	Heating supply of the pressure pipeline	Please contact your dealer.
U 1079	Sensor supply voltage 1	Please contact your dealer.
U 1080	Sensor supply voltage 2	Please contact your dealer.
U 1387	Urea pressure	Please contact your dealer.
U 1388	Urea pressure sensor	Please contact your dealer.
U 1485	Main relay	Please contact your dealer.
U 1677	Modular heater	Please contact your dealer.
U 1761	Level sensor in urea tank	Please contact your dealer.
U 2854 – U 2858	CAN receiver	Please contact your dealer.
U 2859	Urea / Heater or Exhaust Measurement State	Please contact your dealer.
U 2860 – U 2871	CAN message	Please contact your dealer.
U 2872	Error turning on the heater or data control unit	Please contact your dealer.
U 3031	Temperature sensor in urea tank	Please contact your dealer.
U 520201	Power module temperature	Please contact your dealer.
U 520228	NOx emission control	Please contact your dealer.
U 520239	Heater power supply	Please contact your dealer.
U 520243	Urea level	Please contact your dealer.
U 520257	Leakage of urea	Please contact your dealer.
U 520260	Urea pressure	Please contact your dealer.
U 520276	Power supply voltage	Please contact your dealer.
U 520296	NOx control unit	Please contact your dealer.
U 520308	NOx sensor	Please contact your dealer.
U 520310	Temperature in the urea tank	Please contact your dealer.

Transmission error codes

T4107	Transmission oil high pressure sensor malfunction	Please contact your dealer.
T4108	Included range sensor malfunction	Please contact your dealer.
T4124	Parking brake sensor malfunction	Please contact your dealer.
T4128	Transmission control unit malfunction	Use the transmission protection mode. Please contact your dealer.
T412A	Malfunction of the sensor of the estimated gear speed	Use the transmission protection mode. Please contact your dealer.
T412B	Malfunction of the switch of ranges of high / low speeds (“Hare” / “Turtle”)	Please contact your dealer.
T4131	Malfunction of the summing shaft speed sensor	Use the transmission protection mode . Please contact your dealer.
T4142	Malfunction of the summing shaft speed sensor	Use the transmission protection mode. Please contact your dealer.
T4144	Malfunction of the engine speed sensor	Use the transmission protection mode. Please contact your dealer.
T4145	Malfunction of the sensor of the estimated gear speed	Use the transmission protection mode. Please contact your dealer.
T4150	Transmission filter clogging sensor malfunction	Please contact your dealer.
T4153	High transmission oil temperature	Further movement is prohibited. Please contact your dealer.
T4156	Transmission filter clogging sensor malfunction	Please contact your dealer.
T4158	Transmission slip sensor malfunction	Please contact your dealer.
T4159	Malfunction of turning on the transmission protection mode or an error in this mode	Please contact your dealer.
T4161	Malfunction of the solenoid valve of the low speed range (“Turtle”)	Use the transmission protection mode. Please contact your dealer.
T4162	High speed range solenoid valve malfunction (“Hare”)	Use the transmission protection mode. Please contact your dealer.
T4163	Malfunction of the solenoid valve for speed limiting up to 30 km / h	Please contact your dealer.
T4164	Defective clutch solenoid valve	Please contact your dealer.
T4172	Transmission filter clogging sensor malfunction	Please contact your dealer.
T4173	Transmission oil temperature sensor malfunction	Please contact your dealer.
T4174	Parking brake sensor malfunction	Please contact your dealer.
T4182	Malfunction of the calculated gear speed sensor Malfunction of the summing shaft speed sensor	Use the transmission protection mode. Please contact your dealer.
T4183	Malfunction of the calculated gear speed sensor Malfunction of the summing shaft speed sensor	Use the transmission protection mode. Please contact your dealer.
T4192	Malfunction of the switch of the right brake	Please contact your dealer.
T4193	Left Brake Switch Malfunction	Please contact your dealer.
T41A0	Transmission control unit malfunction	Please contact your dealer.
T41A1	Transmission control unit malfunction	Please contact your dealer.
T41A2	Transmission control unit malfunction	Please contact your dealer.
T41A3	Transmission control unit malfunction	Please contact your dealer.
T41A4	Transmission control unit malfunction	Please contact your dealer.
T41A5	Transmission control unit malfunction	Please contact your dealer.
T41A6	Transmission control unit malfunction	Please contact your dealer.
T41B0	CAN bus malfunction	Please contact your dealer.
T41B1	Malfunction of the solenoid valve of the low speed range (“Turtle”)	Please contact your dealer.
T41B2	High speed range solenoid valve malfunction (“Hare”)	Please contact your dealer.
T41C1	Engine stalled due to transmission overload	Reduce the load on the transmissions and try again. Please contact your dealer.
T41D1	Calibration error	Please contact your dealer.
T41D2	Calibration error	Please contact your dealer.
T41D3	Calibration error	Please contact your dealer.
T41D4	Calibration error	Please contact your dealer.
T41D5	Calibration error	Please contact your dealer.
T41D6	Calibration error	Please contact your dealer.
T41D7	Calibration error	Please contact your dealer.
T41D8	Calibration error	Please contact your dealer.
T41D9	Calibration error	Please contact your dealer.
T41DA	Calibration error	Please contact your dealer.
T41DB	Calibration error	Please contact your dealer.
T41DC	Calibration error	Please contact your dealer.
T41DD	Calibration error	Please contact your dealer.
T41DE	Calibration error	Please contact your dealer.
T41DF	Calibration error	Please contact your dealer.
T41 E0	Defective clutch solenoid valve	Please contact your dealer.
T41EB	Included range sensor malfunction	Use the transmission protection mode. Please contact your dealer.
T41EE	The curve of transmission parameters in the program	Use the transmission protection mode. Please contact your dealer.
T41EF	Coupling curve in the program	Please contact your dealer.
T41FF	Malfunction Autotronic 4	Please contact your dealer.

All wheel drive front axle error codes

code	Description	Solution
T5131	4WD switch malfunction	Please contact your dealer.
T5132	4WD switch malfunction	Please contact your dealer.
T5133	Fault full electromagnetic valve actuator	Please contact your dealer.
T5151	Differential lock switch malfunction	Please contact your dealer.
T5153	Differential lock solenoid valve malfunction	Please contact your dealer.
T5154	Left Brake Switch Malfunction	Please contact your dealer.
T5155	Malfunction of the switch of the right brake	Please contact your dealer.
T51FF	Malfunction Autotronic 4	Please contact your dealer.

PTO error codes

T6101	Faulty PTO ON / OFF switch	Please contact your dealer.
T6102	Malfunction of the PTO ON / OFF switch located on the wing	Please contact your dealer.
T6104	Malfunction of the PTO solenoid valve	Please contact your dealer.
T6105	Malfunction of the PTO clutch speed sensor	Please contact your dealer.
T6110	Malfunction of the PTO shaft speed sensor	Please contact your dealer.
T6115	Malfunction of the neutral switch on the PTO control unit	Please contact your dealer.
T6116	Malfunction of the switch of the speed range of 540 rpm on the PTO control unit	Please contact your dealer.
T6117	Malfunction of the ECO speed range switch on the PTO control unit	Please contact your dealer.
T6118	Malfunction of the switch of the speed range of 1000 rpm on the PTO control unit	Please contact your dealer.
T611A	Malfunction of the solenoid valve of the speed range of 540 rpm	Please contact your dealer.
T611B	Malfunction of the ECO PTO speed solenoid valve	Please contact your dealer.
T611C	Malfunction of the solenoid valve of the speed range of 1000 rpm	Please contact your dealer.
T6141	Faulty PTO ON / OFF switch	Please contact your dealer.
T6143	Malfunction of the PTO ON / OFF switch located on the wing	Please contact your dealer.
T6145	Malfunction of the PTO clutch speed sensor	Please contact your dealer.
T6150	Malfunction of the PTO shaft speed sensor	Please contact your dealer.
T6155	Malfunction of the neutral switch on the PTO control unit	Please contact your dealer.
T6156	Malfunction of the switch of the speed range of 540 rpm on the PTO control unit	Please contact your dealer.
T6157	Malfunction of the ECO speed range switch on the PTO control unit	Please contact your dealer.
T6158	Malfunction of the switch of the speed range of 1000 rpm on the PTO control unit	Please contact your dealer.
T6160	Malfunction of the PTO shaft speed sensor Malfunction of the PTO clutch speed sensor	Please contact your dealer.
T61A1	Faulty PTO ON / OFF switch	Please contact your dealer.
T61B5	Malfunction of the neutral switch on the PTO control unit	Please contact your dealer.
T61B6	Malfunction of the switch of the speed range of 540 rpm on the PTO control unit	Please contact your dealer.
T61B7	Malfunction of the ECO speed range switch on the PTO control unit	Please contact your dealer.
T61B8	Malfunction of the switch of the speed range of 1000 rpm on the PTO control unit	Please contact your dealer.

Hydraulic valve error codes

T011493
Reading the error code number.
The code consists of a letter and three numbers.
For example V149:
– V = hydraulic valve
– 1 = number of faulty valve
– 49 = error code number

code	Description	Consequences	Solution
V.43	Malfunction of the valve position sensor line	– When an error code appears , a “beep” is heard. – Error code on the display Instrument panel control unit – All valves locked	– Delete the error code from the control unit of the instrument panel – Unlock the valves (the valve affected by the error code remains blocked). – To reactivate the valve affected by the error code , stop and restart the engine. If the error code is still present, the valve affected by the error code remains blocked. – Contact your dealer.
V.49	Main valve does not return to neutral position	– No – Error code on the display Instrument panel control unit	– Delete error code from Instrument panel control unit – Contact your dealer.
V.52	When starting, the main valve is not in neutral	– No – Error code on the display Instrument panel control unit	– Delete error code from Instrument panel control unit – Contact your dealer.

Press the button (16) to clear the error code on the instrument panel control unit display. on keyboard

Multifunction error codes armrest

01	Output signal error 10 V. Autotronic armrest 5.	Please contact your dealer.
eleven	FingerTIP 1 – short circuit to 0 V.	Please contact your dealer.
12	FingerTIP 1 – short circuit to 12V.	Please contact your dealer.
21	FingerTIP 2 – short circuit to 0 V.	Please contact your dealer.
22	FingerTIP 2 – short circuit to 12V.	Please contact your dealer.
31	FingerTIP 3 – short circuit to 0 V.	Please contact your dealer.
32	FingerTIP 3 – short circuit to 12V.	Please contact your dealer.
41	FingerTIP 4 – short circuit to 0 V.	Please contact your dealer.
42	FingerTIP 4 – short circuit to 12V.	Please contact your dealer.
51	FingerTIP 5 – short circuit to 0 V.	Please contact your dealer.
52	FingerTIP 5 – short circuit to 12V.	Please contact your dealer.
61	FingerTIP 6 – short circuit to 0 V.	Please contact your dealer.
62	FingerTIP 6 – short circuit to 12V.	Please contact your dealer.
71	Throttle position control handle – short circuit to 0 V.	Please contact your dealer.
72	Throttle position control handle – short circuit to 12V.	Please contact your dealer.
81	Rear linkage height adjusting wheel – short circuit to 0 V.	Please contact your dealer.
82	Rear linkage height adjusting wheel – short circuit to 12V.	Please contact your dealer.
91	Transmission lever – short circuit to 0 V.	Please contact your dealer.
92	Transmission lever – short circuit to 12V.	Please contact your dealer.
6	One or more indicator lights are missing	Install indicator bulbs where they are missing.
7	Keyboard not connected	Please contact your dealer.
eight	Checksum error	Please contact your dealer.
9	CAN communication problem	Please contact your dealer.
10	Short circuit in the front roof lights	Please contact your dealer.
eleven	Short circuit in the tail lights on the roof	Please contact your dealer.
12	Short circuit in brake lights	Please contact your dealer.
thirteen	Reversing light short circuit	Please contact your dealer.

The diagnosis tool Massey Ferguson 8450-8460-8470-8480, 8600-8650-8660-8670-8680-8690 Fault Codes List for trucks provides different possibilities such as information on the use and location of the connectors, detection and description of errors, activation of the fan, compression test and other components, system data information and more.

Источник