Kyocera ошибка 0980 - TopOshibok.ru - решение и исправление самых разных ошибок

Catalog
Sign In
Contacts
Forum
Eng

Error Codes
Kyocera
TASKalfa 4501i
Code 0980

Code: 0980
Description: 24 V power down detect
If a 24V power disconnection signal is observed and a 12V power disconnection signal is observed simultaneously for one second.
Causes: Power source PWB.
Remedy: 1. Check the +24V output is given at YC12- 1 to 3 of the power circuit PWB. 2. Replace the power source PWB

Юрий Яраскин » Пт сен 10, 2021 9:34 am

[quote=»Goldwater»]Значит, проблема на плате.[/quote
Вот плата, слева широкий контакт из него 3 и 4 пин это на кнопку закрытия дверцы. Остальные расходятся на другие платы управления. Визуально плата чистенькая. Может есть способ лечения? Или что бы Вы сами сделали в такой ситуации? В парт каталоге нет такой платы. И на просторах инета тоже нет ste_na

Юрий Яраскин

Осматривается

Сайт

[SCANNER ERROR] Lamp Error Kyocera FS-1016

мастерчип в форуме Принтеры, МФУ, факсы, копиры формата A4

3

6735

Усатый Полосатый

Вс окт 28, 2018 11:08 pm
Kyocera FS-1120d индикатор «Нет бумаги»

vs-dos в форуме Принтеры, МФУ, факсы, копиры формата A4

11

15414

СТРОНЦИЙ

Вт ноя 02, 2021 2:24 pm
Kyocera 1035 «бледная» печать

srMax в форуме Принтеры, МФУ, факсы, копиры формата A4

2

14198

srMax

Пт янв 23, 2015 2:49 pm
Kyocera Ecosys M2635dn «поворот» изображения

Искатель в форуме Принтеры, МФУ, факсы, копиры формата A4

10

6309

MatrixAgent

Ср апр 08, 2020 5:18 am
Стирание вала ведущей шестерни в «печке» Kyocera M2035dn

Грецкий орех в форуме Принтеры, МФУ, факсы, копиры формата A4

12

3777

СТРОНЦИЙ

Пн дек 13, 2021 3:35 pm

Вернуться в Принтеры, МФУ, копиры формата A3

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 10

Источник

Code: 0030
Description: FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem.
Causes: Defective FAX control PWB.
Remedy: Replace the fax control PWB and check for correct operation.

Code: 0060
Description: Illegal engine PWB type
The engine main PWB and the engine sub PWB are incompatible.
Causes: Defective engine sub PWB.
Remedy: Replace the engine PWB and check for correct operation.

Code: 0070
Description: FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted.
Causes: Defective FAX software.
Defective FAX control PWB.
Remedy: Defective FAX software. Install the fax software.
Defective FAX control PWB. Replace the fax control PWB and check for correct operation.

Code: 0100
Description: Backup memory device error
Causes: Defective flash memory.
Defective main PWB.
Remedy: Defective flash memory. Replace the main PWB and check for correct operation.
Defective main PWB. Replace the main PWB and check for correct operation.

Code: 0120
Description: MAC address data error
For data in which the MAC address is invalid.
Causes: Defective flash memory
Defective engine PWB.
Remedy: Defective flash memory. Replace the main PWB and check for correct operation.e 1-5-46).

Code: 0150
Description: Backup memory read/write error (engine PWB)
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated 5 times successively. Mismatch of reading data from 2 locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively.
Causes: Improper installation EEPROM.
Device damage of EEPROM.
Remedy: Improper installation EEPROM. Check the installation of the EEPROM and remedy if necessary.
Defective engine PWB. Replace the engine PWB and check for correct operation.
Device damage of EEPROM. Contact the Service Administrative Division.

Code: 0160
Description: Backup memory data error (engine PWB)
Reading data from EEPROM is abnormal.
Causes: Data damage of EEPROM.
Remedy: Contact the Service Administrative Division.

Code: 0170
Description: Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters.
Causes: Data damage of EEPROM.
Defective PWB.
Remedy: Data damage of EEPROM. Contact the Service Administrative Division.
Defective PWB. Replace the main PWB or the engine PWB and check for correct operation.

Code: 0180
Description: Machine number mismatch
Machine number of main and engine does not match.
Causes: Data damage of EEPROM.
Remedy: Contact the Service Administrative Division.

Code: 0620
Description: FAX image DIMM error
DIMM is not installed correctly. DIMM cannot be accessed.
Causes: DIMM installed incorrectly.
Defective main PWB.
Remedy: DIMM installed incorrectly. Check if the DIMM is inserted into the socket on the main PWB correctly.
Defective main PWB. Replace the main PWB and check for correct operation.

Code: 0630
Description: DMA error
DMA transmission of image data does not complete within the specified period of time.
Causes: Poor contact in the connector terminals.
Defective main PWB.
Remedy: Poor contact in the connector terminals. Check the connection the signal cable for CIS and the main PWB, and the continuity across the connector terminals. Repair or replace if necessary.
Defective main PWB. Replace the main PWB and check for correct operation.

Code: 0640
Description: Hard disk error
The hard disk cannot be accessed.
Causes: Defective hard disk.
Defective main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable.
Defective hard disk. Run U024 (HDD formatting) without turning the power off to initialize the hard disk. Replace the hard disk drive and check for correct operation if the problem is still detected after initialization.
Defective main PWB. Replace the main PWB and check for correct operation.

Code: 0650
Description: FAX image DIMM check error
Improper DIMM is installed.
Causes: DIMM installed incorrectly.
Defective main PWB.
Remedy: DIMM installed incorrectly. Check if the DIMM is inserted into the socket on the main PWB correctly.
DIMM of another machine is installed. Perform maintenance mode U671 (RECOVERY FAX DIMM).
Defective main PWB. Replace the main PWB and check for correct operation.

Code: 0800
Description: Image processing error
JAM010X is detected twice.
Causes: Defective main PWB.
Remedy: Replace the main PWB and check for correct operation.

Code: 0830
Description: FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB.
Causes: Defective FAX software.
Defective FAX control PWB.
Remedy: Defective FAX software. Install the fax software.
Defective FAX control PWB. Replace the fax control PWB and check for correct operation.

Code: 0840
Description: Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed.
Causes: The battery is disconnected from the main PWB
Defective main PWB.
Remedy: The battery is disconnected from the main PWB. Check visually and remedy if necessary
Defective main PWB. Replace the main PWB and check for correct operation.

Code: 0870
Description: FAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times
Causes: Improper installation FAX control PWB.
Defective FAX control PWB or main PWB.
Remedy: Improper installation FAX control PWB. Reinstall the FAX control PWB.
Defective FAX control PWB or main PWB. Replace the FAX control PWB or main PWB and check for correct operation.

Code: 0920
Description: Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB.
Causes: Defective FAX control PWB.
Remedy: Replace the fax control PWB and check for correct operation.

Code: 0970
Description: 12 V power down detect Power is disconnected during sleeping.
Causes: Defective power source PWB.
Remedy: Replace the power source PWB and check for correct operation.

Code: 0980
Description: 24 V power down detect 24V disconnection signal is detected for 1 s and 12V disconnection signal is not detected.
Causes: Defective power source PWB.
Remedy: Replace the power source PWB and check for correct operation.

Code: 1000
Description: MP lift motor error
After the MP lift motor is driven, the ON status of MP lift sensors 1 and 2 cannot be detected for 3 s.
Causes: Defective MP plate elevation mechanism.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective MP lift motor.
Defective engine PWB.
Remedy: Defective MP plate elevation mechanism. Check to see if the MP plate can move smoothly and repair it if any problem is found.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. MP lift motor and relay PWB (YC3) Relay PWB (YC12) and feed PWB 1 (YC17) Feed PWB 1 (YC1) and engine PWB (YC6)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective MP lift motor. Replace the MP lift motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 1010
Description: Lift motor 1 error
After cassette 1 is inserted, lift sensor 1 does not turn on within 12 s. This error is detected 5 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 5 times successively.
Causes: Defective bottom plate elevation mechanism in the cassette.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective lift motor 1.
Defective engine PWB.
Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Lift motor 1 and feed PWB 2 (YC3) Feed PWB 2 (YC1) and engine PWB (YC4)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective lift motor 1. Replace the lift motor 1.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 1020
Description: Lift motor 2 error
After cassette 2 is inserted, lift sensor 2 does not turn on within 12 s. This error is detected 5 times successively. The lock signal of the motor is detected continuously for 1 s. This error is detected 5 times successively.
Causes: Defective bottom plate elevation mechanism in the cassette.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective lift motor 2.
Defective engine PWB.
Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Lift motor 2 and feed PWB 2 (YC3) Feed PWB 2 (YC1) and engine PWB (YC4)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective lift motor 2. Replace the lift motor 2.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 1050
Description: SM lift motor error (side multi tray)
After cassette 5 is inserted, SM lift sensor does not turn on within 12 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection.
Causes: Defective bottom plate elevation mechanism in the cassette.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor
Defective SM lift motor.
Defective SM main PWB.
Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. SM lift motor and SM main PWB (YC5)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective SM lift motor. Replace the SM lift motor.
Defective SM main PWB. Replace the SM main PWB (Refer to the service manual for the paper feeder).

Code: 1060
Description: PF lift motor 1 error (side paper feeder)
After cassette 6 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. : The lift over-current protection monitor signal has been detected for 200ms or longer where LFC is installed.
Causes: Defective bottom plate elevation mechanism in the cassette.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective PF lift motor 1.
Defective PF main PWB.
Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 1 and PF main PWB (YC7)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF lift motor 1. Replace the PF lift motor 1.
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 1070
Description: PF lift motor 2 error (side paper feeder)
After cassette 7 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 1 s or more 5 times successively. However, the first 1 s after motor is turned on is excluded from detection. : The lift over-current protection monitor signal has been detected for 200ms or longer where LFC is installed.
Causes: Defective bottom plate elevation mechanism in the cassette.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective PF lift motor 2.
Defective PF main PWB.
Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 2 and PF main PWB (YC7)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF lift motor 2. Replace the PF lift motor 2.
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 1100
Description: PF lift motor 1 error
After cassette 3 is inserted, PF lift sensor 1 does not turn on within 23 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively. However, the first 1 s after PF lift motor 1 is turned on is excluded from detection.
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective PF lift motor 1.
Defective PF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 1 and PF main PWB (YC7)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF lift motor 1. Replace the PF lift motor 1.
Defective PF main PWB. Replace the PF main PWB.

Code: 1110
Description: PF lift motor 2 error
After cassette 4 is inserted, PF lift sensor 2 does not turn on within 23 s. This error is detected 5 times successively. (Time to detect is 2 seconds at the second time and later.) During driving the motor, the lift overcurrent protective monitor signal is detected for 200 ms or more 5 times successively. However, the first 1 s after PF lift motor 2 is turned on is excluded from detection.
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective PF lift motor 2.
Defective PF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 2 and PF main PWB (YC7)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF lift motor 2. Replace the PF lift motor 2.
Defective PF main PWB. Replace the PF main PWB.

Code: 1140
Description: SD lift motor error (side deck)
After cassette 5 is inserted, SD lift sensor does not turn on within 30 s. The lock signal of the motor is detected continuously for 200 ms.
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective SD lift motor.
Defective SD main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. SD lift motor and SD main PWB (YC8)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective SD lift motor. Replace the SD lift motor.
Defective SD main PWB. Replace the SD main PWB (Refer to the service manual for the paper feeder).

Code: 1250
Description: SM multi feed sensor communication error (side multi tray)
A communication error is detected 3 times in succession.
Causes: Improper installation side multi tray.
Defective connector cable or poor contact in the connector.
Defective engine PWB.
Defective SM main PWB.
Remedy: Improper installation side multi tray. Follow installation instruction carefully again.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. SM main PWB (YC1) and engine PWB (YC19)
Defective engine PWB. Replace the engine PWB and check for correct operation.
Defective SM main PWB. Replace the SM main PWB (Refer to the service manual for the paper feeder).

Code: 1350
Description: SM multi feed sensor error (side multi tray)
The SM multi feed sensor has detected multi feeding 5 times successively.
Causes: Defective connector cable or poor contact in the connector.
Defective SM multi feed sensor.
Defective SM main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. SM multi feed sensor and SM main PWB (YC11)
Defective SM multi feed sensor. Replace the SM multi feed sensor.
Defective SM main PWB. Replace the SM main PWB (Refer to the service manual for the paper feeder).

Code: 1410
Description: BR decurler motor error
The BR decurler sensor won’t turn on or off when it was activated for 400 steps (3 times in succession).
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective BR decurler motor.
Defective BR main PWB.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. BR decurler motor and BR main PWB (YC5) BR main PWB (YC2) and engine PWB (YC20)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective BR decurler motor. Replace the BR decurler motor.
Defective BR main PWB. Replace the BR main PWB and check for correct operation.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 1450
Description: SM multi feed sensor backup error (side multi tray)
When writing the data, read and write data does not match 3 times in succession. Deleting a block has failed three times in a row. Writing won’t complete in 200 ms after writing has commenced.
Causes: Defective connector cable or poor contact in the connector.
Defective SM multi feed sensor.
Defective SM main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. SM multi feed sensor and SM main PWB (YC11)
Defective SM multi feed sensor. Replace the SM multi feed sensor.
Defective SM main PWB. Replace the SM main PWB (Refer to the service manual for the paper feeder).

Code: 1720
Description: Paper feeder incompatible detection error
The paper feeder has been installed with a device to which it is incompatible.
Causes: The paper feeder is installed with a device to which it is incompatible.
Remedy: The paper feeder must be installed with the devices to which it is compatible.

Code: 1800
Description: Paper feeder communication error
A communication error from paper feeder is detected 10 times in succession.
Causes: Improper installation paper feeder.
Defective connector cable or poor contact in the connector.
Defective engine PWB.
Defective PF main PWB.
Remedy: Improper installation paper feeder. Follow installation instruction carefully again.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF main PWB (YC13) and engine PWB (YC19)
Defective engine PWB. Replace the engine PWB and check for correct operation.
Defective PF main PWB. Replace the PF main PWB.

Code: 1810
Description: Side multi tray communication error
A communication error from paper feeder is detected 10 times in succession.
Causes: Improper installation side multi tray.
Defective connector cable or poor contact in the connector.
Defective engine PWB.
Defective SM main PWB.
Remedy: Improper installation side multi tray. Follow installation instruction carefully again.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. SM main PWB (YC1) and engine PWB (YC19)
Defective engine PWB. Replace the engine PWB and check for correct operation.
Defective SM main PWB. Replace the SM main PWB (Refer to the service manual for the paper feeder).

Code: 1820
Description: Side paper feeder communication error
A communication error from paper feeder is detected 10 times in succession.
Causes: Improper installation side paper feeder.
Defective connector cable or poor contact in the connector.
Defective engine PWB.
Defective SM main PWB.
Defective PF main PWB.
Remedy: Improper installation side paper feeder. Follow installation instruction carefully again.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF main PWB (YC13) and SM main PWB (YC4) SM main PWB (YC1) and engine PWB (YC19)
Defective engine PWB. Replace the engine PWB and check for correct operation.
Defective SM main PWB. Replace the SM main PWB (Refer to the service manual for the paper feeder).
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 1900
Description: Paper feeder EEPROM error
When writing the data, read and write data does not match 3 times in succession.
Causes: Defective PF main PWB.
Device damage of EEPROM.
Remedy: Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
Device damage of EEPROM. Contact the Service Administrative Division.

Code: 1910
Description: Side multi tray EEPROM error
When writing the data, read and write data does not match 3 times in succession.
Causes: Defective SM main PWB.
Device damage of EEPROM.
Remedy: Defective SM main PWB. Replace the SM main PWB (Refer to the service manual for the paper feeder).
Device damage of EEPROM. Contact the Service Administrative Division.

Code: 1920
Description: Side paper feeder EEPROM error
When writing the data, read and write data does not match 3 times in succession.
Causes: Defective PF main PWB.
Device damage of EEPROM.
Remedy: Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
Device damage of EEPROM. Contact the Service Administrative Division.

Code: 2101
Description: Developer motor error
After developer motor is driven, the ready signal does not turn to L within 2 s. After developer motor is stabilized, the ready signal is at the H level for 1 s continuously.
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective developer motor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer motor and feed PWB 1 (YC8) Feed PWB 1 (YC2) and engine PWB (YC5)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective developer motor. Replace the developer motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 2201
Description: Drum motor steady-state error
The ready signal won’t turn to L in 2 seconds after the drum motor is started. After drum motor is stabilized, the ready signal is at the H level for 5 s continuously. The device won’t engage in ready state in 60 minutes after warming-up has began.
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective drum motor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum motor and feed PWB 1 (YC9) Feed PWB 1 (YC2) and engine PWB (YC5)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective drum motor. Replace the drum motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 2300
Description: Fuser motor error
After fuser motor is driven, the ready signal does not turn to L within 2 s. After fuser motor is stabilized, the ready signal is at the H level for 1 s continuously.
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective fuser motor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser motor and feed PWB 1 (YC18) Feed PWB 1 (YC1) and engine PWB (YC6)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective fuser motor. Replace the fuser motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 2500
Description: Paper feed motor error
After paper feed motor is driven, the ready signal does not turn to L within 2 s. After paper feed motor is stabilized, the ready signal is at the H level for 1 s continuously.
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective paper feed motor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Paper feed motor and feed PWB 2 (YC2) Feed PWB 2 (YC1) and engine PWB (YC4)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective paper feed motor. Replace the paper feed motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 2550
Description: Transfer motor error
After transfer motor is driven, the ready signal does not turn to L within 2 s. After transfer motor is stabilized, the ready signal is at the H level for 1 s continuously.
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective fuser motor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Transfer motor and relay PWB (YC6) Relay PWB (YC5) and feed PWB 1 (YC13) Feed PWB 1 (YC1) and engine PWB (YC6)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective fuser motor. Replace the fuser motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 2600
Description: PF paper feed motor error
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s.
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective PF paper feed motor.
Defective PF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF paper feed motor and PF main PWB (YC16)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF paper feed motor. Replace the PF paper feed motor.
Defective PF main PWB. Replace the PF main PWB.

Code: 2610
Description: PF paper feed motor error (paper feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s.
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective PF paper feed motor.
Defective PF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF paper feed motor and PF main PWB (YC16)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF paper feed motor. Replace the PF paper feed motor.
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 2640
Description: SD paper feed motor error (side deck)
After SD paper feed motor is driven, the ready signal does not turn to L within 2 s.
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective SD paper feed motor.
Defective SD main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. SD paper feed motor and SD main PWB (YC16)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective SD paper feed motor. Replace the SD paper feed motor.
Defective SD main PWB. Replace the SD main PWB (Refer to the service manual for the paper feeder).

Code: 2650
Description: SM paper feed motor error (side multi tray)
After SM paper feed motor is driven, the ready signal does not turn to L within 2 s.
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective SM paper feed motor.
Defective SM main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. SM paper feed motor and SM main PWB (YC5)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective SM paper feed motor. Replace the SM paper feed motor.
Defective SM main PWB. Replace the SM main PWB (Refer to the service manual for the paper feeder).

Code: 2660
Description: PF paper feed motor error (side large capacity feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s.
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective PF paper feed motor.
Defective PF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF paper feed motor and PF main PWB (YC16)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF paper feed motor. Replace the PF paper feed motor.
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 2670
Description: PF paper feed motor error (side paper feeder)
After PF paper feed motor is driven, the ready signal does not turn to L within 2 s.
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective PF paper feed motor.
Defective PF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF paper feed motor and PF main PWB (YC16)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective PF paper feed motor. Replace the PF paper feed motor.
Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).

Code: 3100
Description: Scanner carriage error
The home position is not correct when the power is turned on or at the start of copying using the table.
Causes: Defective connector cable or poor contact in the connector.
Defective home position sensor.
Defective scanner motor.
Defective ISC PWB.
Defective main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Home position sensor and ISC PWB (YC8) Scanner motor and ISC PWB (YC5) ISC PWB (YC3) and main PWB (YC11)
Defective home position sensor. Replace the home position sensor.
Defective scanner motor. Replace the scanner motor.
Defective ISC PWB. Replace the ISC PWB and check for correct operation.
The scanner mirror frame is being locked after setup. Check whether the scanner mirror frame has been unlocked and unlock if necessary.
Defective main PWB. Replace the main PWB and check for correct operation.

Code: 3200
Description: Exposure lamp error
When input value at the time of LED lamp PWB illumination does not exceed the threshold value between 5 s.
Causes: Defective connector cable or poor contact in the connector.
Defective LED lamp PWB.
Defective ISC PWB.
Defective main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and main PWB (YC11)
Defective LED lamp PWB. Replace the LED lamp PWB and check for correct operation.
Defective ISC PWB. Replace the ISC PWB and check for correct operation.
Defective CCD PWB. Replace the ISU and check for correct operation.
Defective main PWB. Replace the main PWB and check for correct operation.

Code: 3210
Description: CIS lamp error
When input value at the time of CIS illumination does not exceed the threshold value between 5 s.
Causes: Defective connector cable or poor contact in the connector.
Defective CIS.
Defective DPSHD PWB.
Defective DP relay PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. CIS and DPSHD PWB (YC2) DPSHD PWB (YC3) and DP relay PWB (YC2)
Defective CIS. Replace the CIS and check for correct operation.
Defective DPSHD PWB. Replace the DPSHD PWB and check for correct operation.
Defective DP relay PWB. Replace the DP relay PWB and check for correct operation.

Code: 3300
Description: Optical system (AGC) error
After AGC, correct input is not obtained at CCD.
Causes: Defective connector cable or poor contact in the connector.
Defective exposure lamp
Defective CCD PWB.
Defective ISC PWB.
Defective main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. LED lamp PWB and ISC PWB (YC6) CCD PWB (YC2) and ISC PWB (YC9) ISC PWB (YC3) and main PWB (YC11)
Defective LED lamp PWB. Replace the LED lamp PWB and check for correct operation.
Defective ISC PWB. Replace the ISC PWB and check for correct operation.
Defective CCD PWB. Replace the ISU and check for correct operation.
Defective main PWB. Replace the main PWB and check for correct operation.

Code: 3310
Description: CIS AGC error After AGC, correct input is not obtained at CIS.
Causes: Defective CIS.
Defective DPSHD PWB.
Defective DP relay PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. CIS and DPSHD PWB (YC2) DPSHD PWB (YC3) and DP relay PWB (YC2)
Defective CIS. Replace the CIS and check for correct operation.
Defective DPSHD PWB. Replace the DPSHD PWB and check for correct operation.
Defective DP relay PWB. Replace the DP relay PWB and check for correct operation.

Code: 3500
Description: Communication error between scanner and ASIC
An error code is detected.
Causes: Defective connector cable or poor contact in the connector.
Defective ISC PWB.
Defective main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. ISC PWB (YC3) and main PWB (YC11)
Defective ISC PWB. Replace the ISC PWB and check for correct operation.
Defective main PWB. Replace the main PWB and check for correct operation.

Code: 3600
Description: Scanner sequence error
Causes: Defective ISC PWB.
Remedy: Replace the ISC PWB and check for correct operation.

Code: 3700
Description: Scanner device error
Causes: CCD connector inserted incorrectly.
Remedy: Reinsert the image scanner unit connector if necessary.

Code: 3800
Description: AFE error
When writing the data, read and write data does not match 3 times in succession. No response is received in 100 ms from AEF.
Causes: Defective ISC PWB.
Remedy: Replace the ISC PWB and check for correct operation.

Code: 3900
Description: Backup memory read/write error (ISC PWB)
Read and write data does not match.
Causes: Defective backup memory or PWB.
Remedy: Replace the ISC PWB and check for correct operation.

Code: 4001
Description: Polygon motor synchronization error
After polygon motor is driven, the ready signal does not turn to L within 30 s. The polygon motor speed won’t stabilize within 10 s.
Causes: Defective connector cable or poor contact in the connector.
Defective polygon motor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Polygon motor and engine PWB (YC15)
Defective polygon motor. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 4011
Description: Polygon motor steady-state error
After polygon motor is stabilized, the ready signal is at the H level for 15 s continuously.
Causes: Defective connector cable or poor contact in the connector.
Defective polygon motor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Polygon motor and engine PWB (YC15)
Defective polygon motor. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 4101
Description: BD initialization error
After polygon motor is driven, ASIC detects a BD error for 1 s.
Causes: Defective connector cable or poor contact in the connector.
Defective PD PWB.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and engine PWB (YC11)
Defective PD PWB. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 4201
Description: BD steady-state error
The BD signal is not detected.
Causes: Defective connector cable or poor contact in the connector.
Defective PD PWB.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and engine PWB (YC11)
Defective PD PWB. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 5101
Description: Main high-voltage error
Measure the inflowing current when Vpp is varied in 3 steps and verify if the difference of the currents of 0 and step 2 is less than 42 (51 if lower high-voltage board).
Causes: Defective connector cable or poor contact in the connector.
Defective high voltage PWB
Defective engine PWB.
Remedy: Improper installation charger roller unit. Reinstall the charger roller unit.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. High voltage PWB (YC2) and engine PWB (YC16)
Defective high voltage PWB. Replace the high voltage PWB and check for correct operation.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6000
Description: Broken fuser heater wire
Fuser thermistor 1 does not reach 100° C/212 °F even after 30 s during warming up. The detected temperature of fuser thermistor 1 does not reach the specified temperature (ready indication temperature) for 30 s in warming up after reached to 100° C/212 °F. A temperature of less than 80°C/176 °F was observed at the fuser thermistor when the temperature at the fuser thermistor 1 reached 100°C/ 212 °F after warming up.
Causes: Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Fuser thermostat triggered.
Defective fuser heater.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Power source PWB (YC3) and fuser IH PWB (YC1) Fuser IH PWB (YC4) and engine PWB (YC26)
Fuser thermostat triggered. Replace the fuser unit.
Defective fuser IH. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6020
Description: Abnormally high fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature higher than 240°C/464°F for 1 s.
Causes: Deformed connector pin.
Defective triac.
Shorted fuser thermistor 1.
Defective engine PWB.
Remedy: Shorted fuser thermistor 1. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6030
Description: Broken fuser thermistor 1 wire
Input from fuser thermistor 1 is 984 or more (A/D value) continuously for 1 s. Except, the A/D value in the differential output won’t change by 4 or more when it was turned on for 10 seconds in a low-temperature environment.
Causes: Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Broken fuser thermistor 1 wire.
Fuser thermostat triggered.
Defective fuser heater.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser unit and engine PWB (YC26)
Broken fuser thermistor 1 wire. Replace the fuser unit.
Fuser thermostat triggered. Replace the fuser unit.
Defective fuser IH. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6040
Description: Fuser heater error
Input from fuser thermistor 1 is abnormal value continuously for 1 s.
Causes: Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Broken fuser thermistor 1 wire.
Defective fuser heater.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser unit and engine PWB (YC26)
Broken fuser thermistor 1 wire. Replace the fuser unit.
Defective fuser IH. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6050
Description: Abnormally low fuser thermistor 1 temperature
Fuser thermistor 1 detects a temperature lower than 100°C/212°F for 1 s after warming up.
Causes: Deformed connector pin.
Defective triac.
Defective fuser thermistor 1.
Defective fuser heater.
Defective engine PWB.
Remedy: Defective fuser thermistor 1. Replace the fuser unit.
Defective fuser IH. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6100
Description: Broken fuser heater wire
Fuser thermistor 5 won’t reach the reference temperature in 480 s after shifting to low power mode.
Causes: Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Broken fuser thermistor 5 wire.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser unit and engine PWB (YC26)
Broken fuser thermistor 5 wire. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6120
Description: Abnormally high fuser thermistor 5 temperature
Fuser thermistor 5 detects a temperature higher than 190C/374F for 1 s.
Causes: Deformed connector pin.
Defective triac.
Shorted fuser thermistor 5.
Defective engine PWB.
Remedy: Shorted fuser thermistor 5. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6130
Description: Broken fuser thermistor 5 wire
Input from fuser thermistor 5 is 992 or more (A/D value) continuously for 60 s.
Causes: Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Broken fuser thermistor 5 wire.
Defective fuser IH.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser unit and engine PWB (YC26)
Broken fuser thermistor 5 wire. Replace the fuser unit.
Defective fuser IH. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6150
Description: Abnormally low fuser thermistor 5 temperature
Fuser thermistor 5 detects a temperature lower than 30C/ 86F for 1 s after warming up.
Causes: Deformed connector pin.
Defective triac.
Defective fuser thermistor 5.
Defective fuser IH.
Defective engine PWB.
Remedy: Defective fuser thermistor 5. Replace the fuser unit.
Defective fuser IH. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6200
Description: Broken fuser edge heater wire
Fuser thermistor 2 does not reach 100° C/212 °F even after 60 s during warming up. The detected temperature of fuser thermistor 2 does not reach the specified temperature (ready indication temperature) for 420 s in warming up after reached to 100° C/212 °F.
Causes: Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Fuser thermostat triggered.
Defective fuser IH.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Power source PWB (YC3) and fuser IH PWB (YC1) Fuser IH PWB (YC4) and engine PWB (YC26)
Fuser thermostat triggered. Replace the fuser unit.
Defective fuser IH. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6220
Description: Abnormally high fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature higher than 240C/464F for 1 s.
Causes: Deformed connector pin.
Defective triac.
Shorted fuser thermistor 2.
Defective engine PWB.
Remedy: Shorted fuser thermistor 2. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6230
Description: Broken fuser thermistor 2 wire
The Input signal from the fuser thermistor 2 is 992 or more (A/D) continuously for 1 second during the temperature detected by the fuser thermistor 1 is 100 deg-C or more.
Causes: Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Broken fuser thermistor 2 wire.
Fuser thermostat triggered.
Defective fuser IH.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser unit and engine PWB (YC26)
Broken fuser thermistor 2 wire. Replace the fuser unit.
Fuser thermostat triggered. Replace the fuser unit.
Defective fuser IH. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6250
Description: Abnormally low fuser thermistor 2 temperature
Fuser thermistor 2 detects a temperature lower than 100C/212F for 1 s during ready or print.
Causes: Deformed connector pin.
Defective triac.
Defective fuser thermistor 2.
Defective fuser IH.
Defective engine PWB.
Remedy: Defective fuser thermistor 2. Replace the fuser unit.
Defective fuser IH. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6320
Description: Abnormally high fuser thermistor 3 temperature
Fuser thermistor 3 detects a temperature higher than 215C/419F for 1 s.
Causes: Deformed connector pin.
Defective triac.
Shorted fuser thermistor 3.
Defective engine PWB.
Remedy: Shorted fuser thermistor 3. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6330
Description: Broken fuser thermistor 3 wire
Fuser thermistor 3 detects a temperature lower than 20C/ 68F continuously for 1 s
Causes: Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Broken fuser thermistor 3 wire.
Fuser thermostat triggered.
Defective fuser IH.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser unit and engine PWB (YC26)
Broken fuser thermistor 3 wire. Replace the fuser unit.
Fuser thermostat triggered. Replace the fuser unit.
Defective fuser IH. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6520
Description: Abnormally high fuser thermistor 4 temperature
Fuser thermistor 4 detects a temperature higher than 215C/419F for 1 s.
Causes: Deformed connector pin.
Defective triac.
Shorted fuser thermistor 4.
Defective engine PWB.
Remedy: Shorted fuser thermistor 4. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6530
Description: Broken fuser thermistor 4 wire
Fuser thermistor 4 detects a temperature lower than 20C/ 68F continuously for 1 s
Causes: Defective connector cable or poor contact in the connector.
Deformed connector pin
Defective triac.
Broken fuser thermistor 4 wire.
Fuser thermostat triggered.
Defective fuser IH.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser unit and engine PWB (YC26)
Broken fuser thermistor 4 wire. Replace the fuser unit.
Fuser thermostat triggered. Replace the fuser unit.
Defective fuser IH. Replace the fuser unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6600
Description: Fuser belt rotation error
A belt rotating pulse is not received for 1 second. (Engine CPU)
Causes: Defective connector cable or poor contact in the connector.
Defective fuser belt sensor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser unit and engine PWB (YC26)
Defective fuser belt sensor. Replace the fuser belt sensor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6610
Description: Fuser release motor error
When the fuser release motor is driven, the fuser release sensor does not turn on/off for 5 s.
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective fuser release motor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser unit and engine PWB (YC26)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective fuser release motor. Replace the fuser release motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6620
Description: IH core motor error
When the IH core motor is driven, the IH core sensor does not turn off for 5 s.
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective IH core motor.
Defective eject PWB.
Defective front PWB.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. IH core motor and eject PWB (YC4) Eject PWB (YC1) and front PWB (YC10) Front PWB (YC9) and engine PWB (YC9)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective IH core motor. Replace the IH core motor.
Defective eject PWB. Replace the eject PWB and check for correct operation.
Defective front PWB. Replace the front PWB and check for correct operation.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6710
Description: Fuser IH PWB CPU reset error
Watch doc timer has been overflowed.
Causes: Defective connector cable or poor contact in the connector.
Defective fuser IH PWB.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser IH PWB (YC4) and engine PWB (YC26)
Defective fuser IH PWB. Replace the fuser IH PWB and check for correct operation.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6720
Description: Fuser IH belt rotation error
A belt rotating pulse is not received for 2 s.
Causes: Defective connector cable or poor contact in the connector.
Defective fuser belt sensor.
Defective fuser IH PWB.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser unit and engine PWB (YC26)
Defective fuser belt sensor. Replace the fuser belt sensor.
Defective fuser IH PWB. Replace the fuser IH PWB and check for correct operation.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6730
Description: Abnormally high fuser IH PWB temperature 1
The input detect temperature is greater than 105°C/221 °F.
Causes: Defective connector cable or poor contact in the connector.
Defective fuser IH PWB.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser IH PWB (YC4) and engine PWB (YC26)
Defective fuser IH PWB. Replace the fuser IH PWB and check for correct operation.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6740
Description: Abnormally high fuser IH PWB temperature 2
The input detect temperature is greater than 105°C/221 °F.
Causes: Defective connector cable or poor contact in the connector.
Defective fuser IH PWB.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser IH PWB (YC4) and engine PWB (YC26)
Defective fuser IH PWB. Replace the fuser IH PWB and check for correct operation.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6750
Description: Fuser IH output over-current error
The output current is greater than 75A for 10 ms in succession.
Causes: Defective connector cable or poor contact in the connector.
Defective fuser IH PWB.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser IH PWB (YC4) and engine PWB (YC26)
Defective fuser IH PWB. Replace the fuser IH PWB and check for correct operation.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6760
Description: Fuser IH input over-current error
The input current is greater than 20A for 100 ms in succession.
Causes: Defective connector cable or poor contact in the connector.
Defective fuser IH PWB.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser IH PWB (YC4) and engine PWB (YC26)
Defective fuser IH PWB. Replace the fuser IH PWB and check for correct operation.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6770
Description: Fuser IH low electric power error
The preset power is less than 0.6 times of it for 120 ms in succession.
Causes: Defective connector cable or poor contact in the connector.
Defective fuser IH PWB.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser IH PWB (YC4) and engine PWB (YC26)
Defective fuser IH PWB. Replace the fuser IH PWB and check for correct operation.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6780
Description: Fuser IH input over-voltage error
The input voltage is greater than 140V for 200 ms in succession.
Causes: Defective connector cable or poor contact in the connector.
Defective fuser IH PWB.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser IH PWB (YC4) and engine PWB (YC26)
Defective fuser IH PWB. Replace the fuser IH PWB and check for correct operation.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6900
Description: Fuser belt cooling fan error
When the fuser front or rear fan motor is driven, alarm signal is detected for 5 s continuously.
Causes: Defective connector cable or poor contact in the connector.
Defective fuser front or rear fan motor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser front fan motor and front PWB (YC4) Front PWB (YC3) and engine PWB (YC7) Fuser rear fan motor and engine PWB (YC26)
Defective fuser front or rear fan motor. Replace the fuser front or rear fan motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6940
Description: IH fan motor error
When the IH fan motor is driven, the alarm signal is detected for 5 s continuously.
Causes: Defective connector cable or poor contact in the connector.
Defective IH fan motor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. IH fan motor and feed PWB 1 (YC11) Feed PWB 1 (YC2) and engine PWB (YC5)
Defective IH fan motor. Replace the IH fan motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6950
Description: Fuser IH PWB communication error
No response is received in 30 ms since a command is sent to IHCPU. A checksum error is detected 10 times in succession.
Causes: Defective connector cable or poor contact in the connector.
Defective fuser IH PWB.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser IH PWB (YC4) and engine PWB (YC26)
Defective fuser IH PWB. Replace the fuser IH PWB and check for correct operation.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6990
Description: Fuser power supply incompatibility Information won’t match between the engine backup and the fuser IH PWB.
Causes: Defective fuser IH PWB.
Defective engine PWB.
Remedy: Defective fuser IH PWB. Replace the fuser IH PWB and check for correct operation.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7001
Description: Toner motor error
During the toner motor is driven, an event in which a locking was detected for 5 times in 200 ms intervals has occurred in 30 sets.
Causes: Defective connector cable or poor contact in the connector.
Defective toner motor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Toner motor and engine PWB (YC27)
Defective toner motor. Replace the toner motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7101
Description: Toner sensor error
Sensor output value of 60 or less or 944 or more continued for 3 s.
Causes: Defective connector cable or poor contact in the connector.
Defective toner sensor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Toner sensor and front PWB (YC7) Front PWB (YC2) and engine PWB (YC8)
Defective toner sensor. Replace developer unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7200
Description: Broken outer temperature sensor wire
The sensor input sampling is greater than 230.
Causes: Defective connector cable or poor contact in the connector.
Defective outer temperature sensor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Outer temperature sensor and front PWB (YC8) Front PWB (YC2) and engine PWB (YC8)
Defective outer temperature sensor. Replace outer temperature sensor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7210
Description: Short-circuited outer temperature sensor
The sensor input sampling is less than 69.
Causes: Defective connector cable or poor contact in the connector.
Defective outer temperature sensor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Outer temperature sensor 2 and front PWB (YC8) Front PWB (YC2) and engine PWB (YC8)
Defective outer temperature sensor. Replace outer temperature sensor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7221
Description: Broken LSU thermistor wire
The sensor input sampling is greater than 230.
Causes: Defective connector cable or poor contact in the connector.
Defective LSU thermistor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and engine PWB (YC11)
Defective LSU thermistor. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7231
Description: Short-circuited LSU thermistor
The sensor input sampling is less than 69.
Causes: Defective connector cable or poor contact in the connector.
Defective LSU thermistor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Laser scanner unit and LSU relay PWB (YC3) LSU relay PWB (YC2) and engine PWB (YC11)
Defective LSU thermistor. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7241
Description: Broken developer thermistor wire
The sensor input sampling is greater than 230.
Causes: Defective connector cable or poor contact in the connector.
Defective developer thermistor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit and front PWB (YC7) Front PWB (YC2) and engine PWB (YC8)
Defective developer thermistor. Replace developer unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7251
Description: Short-circuited developer thermistor
The sensor input sampling is less than 69.
Causes: Defective connector cable or poor contact in the connector.
Defective developer thermistor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit and front PWB (YC7) Front PWB (YC2) and engine PWB (YC8)
Defective developer thermistor. Replace developer unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7301
Description: Toner hopper motor error
When the toner hopper motor is driven, toner hopper sensor does not turn on within 200 ms. This error is detected 15 times successively.
Causes: Defective connector cable or poor contact in the connector.
Defective drive transmission system of motor.
Defective toner hopper sensor.
Defective toner hopper motor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Toner hopper motor and front PWB (YC5) Front PWB (YC3) and engine PWB (YC7)
Defective drive transmission system of motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
Defective toner hopper sensor. Replace the toner hopper sensor.
Defective toner hopper motor. Replace the toner hopper motor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7401
Description: Developer unit type mismatch error
Absence of the developer unit is detected.
Causes: Defective connector cable or poor contact in the connector.
Different type of the developer unit is installed.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit and front PWB (YC7) Front PWB (YC2) and engine PWB (YC8)
Different type of the developer unit is installed. Install the correct developer unit.

Code: 7411
Description: Drum unit type mismatch error
Absence of the drum unit is detected.
Causes: Defective connector cable or poor contact in the connector.
Different type of the drum unit is installed.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit and front PWB (YC6) Front PWB (YC2) and engine PWB (YC8)
Different type of the drum unit is installed. Install the correct drum unit.

Code: 7460
Description: Developer shutter error
Power is turned on while the developer shutter is locked.
Causes: The developer shutter has been locked.
Defective connector cable or poor contact in the connector.
Remedy: The developer shutter has been locked. Release the developer shutter.
Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer shutter sensor and front PWB (YC4) Front PWB (YC3) and engine PWB (YC7)

Code: 7601
Description: ID sensor error Dark potential error
FrontDarkP and FrontDarkS are greater than 0.80V. Light potential error FrontBrightS is smaller than FrontDarkS. FrontBrightP is smaller than FrontDarkP + 0.5V
Causes: Defective connector cable or poor contact in the connector.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. ID sensor and relay PWB (YC10) Relay PWB (YC1) and feed PWB 1 (YC14) Feed PWB 1 (YC2) and engine PWB (YC5)
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7602
Description: ID sensor error
Dark potential error RearDarkP and RearDarkS are greater than 0.80V. Light potential error RearBrightS is smaller than RearDarkS. RearBrightP is smaller than RearDarkP + 0.5V.
Causes: Defective connector cable or poor contact in the connector.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. ID sensor and relay PWB (YC10) Relay PWB (YC1) and feed PWB 1 (YC14) Feed PWB 1 (YC2) and engine PWB (YC5)
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7800
Description: Broken outer temperature sensor wire
The device did not respond for more than 5 ms during reading, in 5 times.
Causes: Defective connector cable or poor contact in the connector.
Defective outer temperature sensor.
Defective engine PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Outer temperature sensor and front PWB (YC8) Front PWB (YC2) and engine PWB (YC8)
Defective outer temperature sensor. Replace outer temperature sensor.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 7901
Description: Drum EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively.
Causes: Defective connector cable or poor contact in the connector.
Defective drum PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum PWB and front PWB (YC6) Front PWB (YC2) and engine PWB (YC8)
Defective drum PWB. Replace the drum unit.

Code: 7911
Description: Developer unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively.
Causes: Defective connector cable or poor contact in the connector.
Defective developer unit.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developer unit and front PWB (YC7) Front PWB (YC2) and engine PWB (YC8)
Defective developer unit. Replace the developer unit.

Code: 7941
Description: Laser scanner unit EEPROM error
Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively.
Causes: Defective connector cable or poor contact in the connector.
Defective APC PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. APC PWB and LSU relay PWB (YC3) LSU relay PWB (YC2) and engine PWB (YC11)
Defective APC PWB. Replace the laser scanner unit.

Code: 8000
Description: Finisher incompatible detection error
The finisher has been installed with a device to which it is incompatible.
Causes: The finisher is installed with a device to which it is incompatible.
Remedy: The finisher must be installed with the devices to which it is compatible.

Code: 8010
Description: Punch motor error 1
When the punch motor is driven, punch home position sensor does not turn on within 200 ms.
Causes: Defective connector cable or poor contact in the connector.
Defective punch home position sensor.
Defective punch motor.
Defective PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Punch motor and punch PWB (YC4) Punch home position sensor and punch PWB (YC8) Punch PWB (YC1) and DF main PWB (YC7)
Defective punch home position sensor. Replace the punch home position sensor.
Defective punch motor. Replace the punch motor.
Defective PWB. Replace the punch PWB or DF main PWB and check for correct operation.

Code: 8020
Description: Punch motor error 2
Home position is not obtained in 3 seconds after home position is initialized or in standby.
Causes: Defective connector cable or poor contact in the connector.
Defective punch motor.
Defective PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Punch motor and punch PWB (YC4) Punch PWB (YC1) and DF main PWB (YC7)
Defective punch motor. Replace the punch motor.
Defective PWB. Replace the punch PWB or DF main PWB and check for correct operation.

Code: 8030
Description: Punch motor error 3
Home position does not turn from On to Off in 50 ms after home position has been initialized.
Causes: Defective connector cable or poor contact in the connector.
Defective punch motor.
Defective PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Punch motor and punch PWB (YC4) Punch PWB (YC1) and DF main PWB (YC7)
Defective punch motor. Replace the punch motor.
Defective PWB. Replace the punch PWB or DF main PWB and check for correct operation.

Code: 8090
Description: DF paddle motor error
When the DF paddle motor is driven, DF paddle sensor does not turn on within 1 s.
Causes: Defective connector cable or poor contact in the connector.
Defective DF paddle sensor.
Defective DF paddle motor.
Defective DF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF paddle motor and DF main PWB (YC15) DF paddle sensor and DF main PWB (YC22)
Defective DF paddle sensor. Replace the DF paddle sensor.
Defective DF paddle motor. Replace the DF paddle motor.
Defective DF main PWB. Replace the DF main PWB and check for correct operation.

Code: 8100
Description: DF eject release motor error
When the DF eject release motor is driven, DF bundle discharge sensor does not turn on within 1 s.
Causes: Defective connector cable or poor contact in the connector.
Defective DF bundle discharge sensor.
Defective DF eject release motor.
Defective DF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF eject release motor and DF main PWB (YC12) DF bundle discharge sensor and DF main PWB (YC22)
Defective DF bundle discharge sensor. Replace the DF bundle discharge sensor.
Defective DF eject release motor. Replace the DF eject release motor.
Defective DF main PWB. Replace the DF main PWB and check for correct operation.

Code: 8110
Description: DF shift motor 1 error (4000-sheet finisher)
When the DF shift motor 1 is driven, DF shift sensor 1 does not turn on within 160 ms.
Causes: Defective connector cable or poor contact in the connector.
Defective DF shift sensor 1.
Defective DF shift motor 1.
Defective DF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF shift motor 1 and DF main PWB (YC14) DF shift sensor 1 and DF main PWB (YC23)
Defective DF shift sensor 1. Replace the DF shift sensor 1.
Defective DF shift motor 1. Replace the DF shift motor 1.
Defective DF main PWB. Replace the DF main PWB and check for correct operation.

Code: 8120
Description: DF shift motor 2 error (4000-sheet finisher)
When the DF shift motor 2 is driven, DF shift sensor 2 does not turn on within 160 ms.
Causes: Defective connector cable or poor contact in the connector.
Defective DF shift sensor 2.
Defective DF shift motor 2.
Defective DF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF shift motor 2 and DF main PWB (YC14) DF shift sensor 2 and DF main PWB (YC23)
Defective DF shift sensor 2. Replace the DF shift sensor 2.
Defective DF shift motor 2. Replace the DF shift motor 2.
Defective DF main PWB. Replace the DF main PWB and check for correct operation.

Code: 8130
Description: DF shift release motor error (4000-sheet finisher) When the DF shift release motor is driven, DF shift release sensor does not turn on within 1 s.
Causes: Defective connector cable or poor contact in the connector.
Defective DF shift release sensor.
Defective DF shift release motor.
Defective DF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF shift release motor and DF main PWB (YC14) DF shift release sensor and DF main PWB (YC23)
Defective DF shift release sensor. Replace the DF shift release sensor.
Defective DF shift release motor. Replace the DF shift release motor.
Defective DF main PWB. Replace the DF main PWB and check for correct operation.

Code: 8140
Description: DF tray motor error 1
When the main tray has started ascending, DF tray sensor 1 or DF tray upper surface sensor does not turn on within 20 s.
Causes: Defective connector cable or poor contact in the connector.
Defective sensor.
Defective DF tray motor.
Defective DF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF tray motor and DF main PWB (YC16) DF tray sensor 1 and DF main PWB (YC22) DF tray upper surface sensor and DF main PWB (YC21, YC13)
Defective sensor. Replace DF tray sensor 1 or DF tray upper surface sensor.
Defective DF tray motor. Replace the DF tray motor.
Defective DF main PWB. Replace the DF main PWB and check for correct operation.

Code: 8150
Description: DF tray motor error 2
When the main tray has descended, DF tray sensor 1 or DF tray upper surface sensor does not turn off within 5s.
Causes: Defective connector cable or poor contact in the connector.
Defective sensor.
Defective DF tray motor.
Defective DF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF tray motor and DF main PWB (YC16) DF tray sensor 1 and DF main PWB (YC22) DF tray upper surface sensor and DF main PWB (YC21, YC13)
Defective sensor. Replace DF tray sensor 1 or DF tray upper surface sensor.
Defective DF tray motor. Replace the DF tray motor.
Defective DF main PWB. Replace the DF main PWB and check for correct operation.

Code: 8160
Description: DF tray motor error 3
When the main tray has descended, DF tray sensor 3 does not turn on within 20 s.
Causes: Defective connector cable or poor contact in the connector.
Defective DF tray sensor 3.
Defective DF tray motor.
Defective DF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF tray motor and DF main PWB (YC16) DF tray sensor 3 and DF main PWB (YC23)
Defective DF tray sensor 3. Replace DF tray sensor 3.
Defective DF tray motor. Replace the DF tray motor.
Defective DF main PWB. Replace the DF main PWB and check for correct operation.

Code: 8170
Description: DF side registration motor 1 error 1
When initial operation, DF side registration sensor 1 does not turn on within 3 s.
Causes: Defective connector cable or poor contact in the connector.
Defective DF side registration sensor 1.
Defective DF side registration motor 1.
Defective DF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF side registration motor 1 and DF main PWB (YC15) DF side registration sensor 1 and DF main PWB (YC22)
Defective DF side registration sensor 1. Replace DF side registration sensor 1.
Defective DF side registration motor 1. Replace DF side registration motor 1.
Defective DF main PWB. Replace the DF main PWB and check for correct operation.

Code: 8180
Description: DF side registration motor 1 error 2
JAM6810 is detected twice.
Causes: Defective connector cable or poor contact in the connector.
Defective DF side registration sensor 1.
Defective DF side registration motor 1.
Defective DF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF side registration motor 1 and DF main PWB (YC15) DF side registration sensor 1 and DF main PWB (YC22)
Defective DF side registration sensor 1. Replace DF side registration sensor 1.
Defective DF side registration motor 1. Replace DF side registration motor 1.
Defective DF main PWB. Replace the DF main PWB and check for correct operation.

Code: 8190
Description: DF side registration motor 2 error 1
When initial operation, DF side registration sensor 2 does not turn on within 3 s.
Causes: Defective connector cable or poor contact in the connector.
Defective DF side registration sensor 2.
Defective DF side registration motor 2.
Defective DF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF side registration motor 2 and DF main PWB (YC15) DF side registration sensor 2 and DF main PWB (YC22)
Defective DF side registration sensor 2. Replace DF side registration sensor 2.
Defective DF side registration motor 2. Replace DF side registration motor 2.
Defective DF main PWB. Replace the DF main PWB and check for correct operation.

Code: 8200
Description: DF side registration motor 2 error 2
JAM6910 is detected twice.
Causes: Defective connector cable or poor contact in the connector.
Defective DF side registration sensor 2.
Defective DF side registration motor 2.
Defective DF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF side registration motor 2 and DF main PWB (YC15) DF side registration sensor 2 and DF main PWB (YC22)
Defective DF side registration sensor 2. Replace DF side registration sensor 2.
Defective DF side registration motor 2. Replace DF side registration motor 2.
Defective DF main PWB. Replace the DF main PWB and check for correct operation.

Code: 8210
Description: DF slide motor error
When initial operation, DF staple sensor does not turn on within 3 s.
Causes: Defective connector cable or poor contact in the connector.
Defective DF staple sensor.
Defective DF slide motor.
Defective DF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF slide motor and DF main PWB (YC12) DF staple sensor and DF main PWB (YC22)
Defective DF staple sensor. Replace the DF staple sensor.
Defective DF slide motor. Replace the DF slide motor.
Defective DF main PWB. Replace the DF main PWB and check for correct operation.

Code: 8230
Description: DF staple motor error 1
Staple JAM (DF) has been detected twice in a row. (The home position could not be detected in 600 ms since the motor was driven after jam was detected twice.)
Causes: Defective connector cable or poor contact in the connector.
Defective DF staple sensor.
Defective DF staple motor.
Defective DF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Staple unit and DF main PWB (YC17)
Defective DF staple sensor. Defective DF staple motor. Replace the staple unit.
Defective DF main PWB. Replace the DF main PWB and check for correct operation.

Code: 8240
Description: DF staple motor error 2
Staple JAM (DF) has been detected twice in a row. (The second JAM detection condition fullfilled with a lock detection signal maintained 1 V for 500 ms continuously, while the stapler motor was driven.)
Causes: Defective connector cable or poor contact in the connector.
Defective DF staple motor.
Defective DF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Staple unit and DF main PWB (YC17)
Defective DF staple motor. Replace the staple unit.
Defective DF main PWB. Replace the DF main PWB and check for correct operation.

Code: 8250
Description: DF tray motor error 4
The lock signal of the motor is detected continuously for 10 s.
Causes: Defective connector cable or poor contact in the connector.
Defective DF tray motor.
Defective DF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF tray motor and DF main PWB (YC16) DF tray sensor 3 and DF main PWB (YC23)
Defective DF tray motor. Replace the DF tray motor.
Defective DF main PWB. Replace the DF main PWB and check for correct operation.

Code: 8300
Description: Center-folding unit communication error (4000-sheet finisher)
Communication with the center-folding unit is not possible.
Causes: Defective connector cable or poor contact in the connector.
Defective CF set sensor.
Defective PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. CF main PWB (YC7) and DF main PWB (YC9)
Defective CF set sensor. Replace the CF set sensor.
Defective PWB. Replace the CF main PWB or the DF main PWB and check for correct operation.

Code: 8310
Description: CF side registration motor 2 error (4000-sheet finisher)
When initial operation, CF side registration sensor 2 does not turn on within 1 s.
Causes: Defective connector cable or poor contact in the connector.
Defective CF side registration sensor 2.
Defective CF side registration motor 2.
Defective CF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. CF side registration motor 2 and CF main PWB (YC10) CF side registration sensor 2 and CF main PWB (YC20)
Defective CF side registration sensor 2. Replace CF side registration sensor 2.
Defective CF side registration motor 2. Replace CF side registration motor 2.
Defective CF main PWB. Replace the CF main PWB and check for correct operation.

Code: 8320
Description: CF adjustment motor error (4000-sheet finisher)
When initial operation, CF adjustment sensor does not turn on within 2.5 s.
Causes: Defective connector cable or poor contact in the connector.
Defective CF adjustment sensor 1, 2.
Defective CF adjustment motor 1, 2.
Defective CF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. CF adjustment motor 1, 2 and CF main PWB (YC10) CF adjustment sensor 1, 2 and CF main PWB (YC20)
Defective CF adjustment sensor 1, 2. Replace CF adjustment sensor 1, 2.
Defective CF adjustment motor 1, 2. Replace CF adjustment motor 1, 2.
Defective CF main PWB. Replace the CF main PWB and check for correct operation.

Code: 8330
Description: CF blade motor error (4000-sheet finisher)
When initial operation, CF blade sensor does not turn on within 3 s.
Causes: Defective connector cable or poor contact in the connector.
Defective CF blade sensor.
Defective CF blade motor.
Defective CF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. CF blade motor and CF main PWB (YC15) CF blade sensor and CF main PWB (YC20)
Defective CF blade sensor. Replace the CF blade sensor.
Defective CF blade motor. Replace the CF blade motor.
Defective CF main PWB. Replace the CF main PWB and check for correct operation.

Code: 8340
Description: CF staple motor error 1 (4000-sheet finisher)
Staple JAM (Folding unit) has been detected twice in a row. (The home position could not be detected in 600 ms since the motor was driven after jam was detected twice.)
Causes: Defective connector cable or poor contact in the connector.
Defective CF staple sensor.
Defective CF staple motor.
Defective CF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. CF staple unit and CF main PWB (YC13)
Defective CF staple sensor. Defective CF staple motor. Replace the CF staple unit.
Defective CF main PWB. Replace the CF main PWB and check for correct operation.

Code: 8350
Description: CF side registration motor 1 error (4000-sheet finisher)
When initial operation, CF side registration sensor 1 does not turn on within 1 s.
Causes: Defective connector cable or poor contact in the connector.
Defective CF side registration sensor 1.
Defective CF side registration motor 1.
Defective CF main PWB
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. CF side registration motor 1 and CF main PWB (YC10) CF side registration sensor 1 and CF main PWB (YC20)
Defective CF side registration sensor 1. Replace CF side registration sensor 1.
Defective CF side registration motor 1. Replace CF side registration motor 1.
Defective CF main PWB. Replace the CF main PWB and check for correct operation.

Code: 8360
Description: CF main motor error (4000-sheet finisher)
During driving the motor, lock signal is detected for 1 s continuously
Causes: Defective connector cable or poor contact in the connector.
Defective CF main motor.
Defective CF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. CF main motor and CF main PWB (YC16)
Defective CF main motor. Replace the CF main motor.
Defective CF main PWB. Replace the CF main PWB and check for correct operation.

Code: 8370
Description: CF staple motor error 2 (4000-sheet finisher)
Staple JAM (DF) has been detected twice in a row. (The home position could not be detected in 600 ms since the motor was driven after jam was detected twice.)
Causes: Defective connector cable or poor contact in the connector.
Defective CF staple motor.
Defective CF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. CF staple unit and CF main PWB (YC13)
Defective CF staple motor. Replace the CF staple unit.
Defective CF main PWB. Replace the CF main PWB and check for correct operation.

Code: 8410
Description: Punch slide motor error 1
The punch slide sensor won’t turn On when home position has been moved by 30 mm.
Causes: Defective connector cable or poor contact in the connector.
Defective slide sensor.
Defective punch slide motor.
Defective PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Punch slide motor and punch PWB (YC3) Punch slide sensor and punch PWB (YC6) Punch PWB (YC1) and DF main PWB (YC7)
Defective slide sensor. Replace the punch slide sensor.
Defective punch slide motor. Replace the punch slide motor.
Defective PWB. Replace the punch PWB or DF main PWB and check for correct operation.

Code: 8420
Description: Punch slide motor error 2
In detection of paper edges, the paper edge cannot be detected in 30 mm move.
Causes: Defective connector cable or poor contact in the connector.
Defective punch slide motor.
Defective PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Punch slide motor and punch PWB (YC3) Punch PWB (YC1) and DF main PWB (YC7)
Defective punch slide motor. Replace the punch slide motor.
Defective PWB. Replace the punch PWB or DF main PWB and check for correct operation.

Code: 8430
Description: Punch unit communication error
Communication failed to be established after the punch unit was hooked up.
Causes: Defective connector cable or poor contact in the connector.
Defective PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Punch PWB (YC1) and DF main PWB (YC7)
Defective PWB. Replace the punch PWB or the DF main PWB and check for correct operation.

Code: 8500
Description: Mailbox communication error (4000-sheet finisher)
Communication failed to be established after the mailbox was hooked up.
Causes: Defective connector cable or poor contact in the connector.
Defective PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. MB main PWB (YC3) and DF main PWB (YC6)
Defective PWB. Replace the MB main PWB or the DF main PWB and check for correct operation.

Code: 8510
Description: MB conveying motor error 1 (4000-sheet finisher)
When initial operation, MB home position sensor does not turn on within 5 s.
Causes: Defective connector cable or poor contact in the connector.
Defective MB home position sensor.
Defective MB conveying motor.
Defective MB main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. MB conveying motor and MB main PWB (YC5) MB home position sensor and MB main PWB (YC2)
Defective MB home position sensor. Replace the MB home position sensor.
Defective MB conveying motor. Replace the MB conveying motor.
Defective MB main PWB. Replace the MB main PWB and check for correct operation.

Code: 8520
Description: MB conveying motor error 2 (4000-sheet finisher)
When standby operation, MB home position sensor does not turn off within 1 s.
Causes: Defective connector cable or poor contact in the connector.
Defective MB home position sensor.
Defective MB conveying motor
Defective MB main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. MB conveying motor and MB main PWB (YC5) MB home position sensor and MB main PWB (YC2)
Defective MB home position sensor. Replace the MB home position sensor.
Defective MB conveying motor. Replace the MB conveying motor.
Defective MB main PWB. Replace the MB main PWB and check for correct operation.

Code: 8800
Description: Document finisher communication error
Communication failed to be established after the document finisher was hooked up.
Causes: Defective connector cable or poor contact in the connector.
Defective PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF main PWB (YC4) and engine PWB (YC18)
Defective PWB. Replace the DF main PWB or the engine PWB and check for correct operation.

Code: 8900
Description: Document finisher backup error
Read and write data does not match 3 times in succession.
Causes: Defective connector cable or poor contact in the connector.
Improper installation EEPROM.
Defective DF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DF main PWB (YC4) and engine PWB (YC18)
Improper installation EEPROM. Check the installation of the EEPROM and remedy if necessary.
Defective DF main PWB. Replace the DF main PWB and check for correct operation.

Code: 8930
Description: Center-folding unit backup error (4000-sheet finisher)
Read and write data does not match 3 times in succession.
Causes: Defective connector cable or poor contact in the connector.
Improper installation EEPROM.
Defective CF main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. CF main PWB (YC7) and DF main PWB (YC9)
Improper installation EEPROM. Check the installation of the EEPROM and remedy if necessary.
Defective CF main PWB. Replace the CF main PWB and check for correct operation.

Code: 9000
Description: Document processor communication error
Communication with the document processor is not possible.
Causes: Defective connector cable or poor contact in the connector
Defective PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DP main PWB (YC1) and ISC PWB (YC12) ISC PWB (YC3) and main PWB (YC11)
Defective PWB. Replace the DP main PWB or the ISC PWB and check for correct operation.

Code: 9010
Description: Coin vender communication error
A communication error from coin vender is detected 10 times in succession.
Causes: Defective connector cable or poor contact in the connector.
Data setup failure.
Defective coin vender control PWB.
Defective PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable.
Data setup failure. Set maintenance mode U206 to off when a coin vender is not installed.
Defective coin vender control PWB. Replace the coin vender control PWB.
Defective PWB. Replace the main PWB and check for correct operation.

Code: 9040
Description: DP lift motor going up error
When the DP lift motor is driven, DP lift sensor 1 does not turn on within 2 s.
Causes: Defective connector cable or poor contact in the connector.
Defective DP lift sensor 1.
Defective DP lift motor.
Defective DP main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DP lift motor and DP main PWB (YC5) DP lift sensor 1 and DP main PWB (YC4)
Defective DP lift sensor 1. Replace the DP lift sensor 1.
Defective DP lift motor. Replace the DP lift motor.
Defective DP main PWB. Replace the DP main PWB and check for correct operation.

Code: 9050
Description: DP lift motor going down error
When the DP lift motor is driven, DP lift sensor 2 does not turn on within 2 s.
Causes: Defective connector cable or poor contact in the connector.
Defective DP lift sensor 2.
Defective DP lift motor.
Defective DP main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DP lift motor and DP main PWB (YC5) DP lift sensor 2 and DP main PWB (YC2)
Defective DP lift sensor 2. Replace the DP lift sensor 2.
Defective DP lift motor. Replace the DP lift motor.
Defective DP main PWB. Replace the DP main PWB and check for correct operation.

Code: 9060
Description: DP EEPROM error
Mismatch of reading data from two locations occurs 3 times successively. Mismatch between writing data and reading data occurs 3 times successively.
Causes: Defective DP main PWB.
Device damage of EEPROM.
Remedy: Defective DP main PWB. Replace the DP main PWB and check for correct operation.
Device damage of EEPROM. Contact the Service Administrative Division.

Code: 9070
Description: Communication error between DP and SHD
A communication error is detected.
Causes: Defective connector cable or poor contact in the connector.
Defective DPSHD PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DPSHD PWB (YC1) and DP main PWB (YC10)
Defective DPSHD PWB. Replace the DPSHD PWB and check for correct operation.

Code: 9080
Description: LED fault detection
When the power supply is turned on, the peak value of LED is 80hex or less.
Causes: Defective connector cable or poor contact in the connector.
Defective CIS
Defective DPSHD PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. CIS and DPSHD PWB (YC1) DPSHD PWB (YC1) and DP main PWB (YC10)
Defective CIS. Replace CIS and check for correct operation.
Defective DPSHD PWB. Replace the DPSHD PWB and check for correct operation.

Code: 9100
Description: Coin vender control PWB error
Communication error has been detected at the coin mec of the coin vender control PWB.
Causes: Defective coin vender control PWB.
Remedy: Replace the coin mec.

Code: 9110
Description: Coin vender error
Communication error has been detected in connection with the coin mec and the rejector.
Causes: Rejector installed incorrectly.
Defective rejector.
Remedy: Rejector installed incorrectly. Check the rejector is properly installed and, if not, perform the corrective action.
Defective rejector. Replace the rejector.

Code: 9120
Description: Sensor error in coin vender change (Yen 10)
Change is empty despite change is enough.
Causes: Coin jam in the change tube
Poor contact in the connector.
Defective change empty sensor.
Defective coin vender control PWB.
Remedy: Coin jam in the change tube Check visually and remedy.
Poor contact in the connector. Check if the change empty sensor is intact.
Defective change empty sensor. Replace the coin mec.
Defective coin vender control PWB. Replace the coin mec.

Code: 9130
Description: Sensor error in coin vender change (Yen 50)
Change is empty despite change is enough.
Causes: Coin jam in the change tube
Poor contact in the connector.
Defective change empty sensor.
Defective coin vender control PWB.
Remedy: Coin jam in the change tube Check visually and remedy.
Poor contact in the connector. Check if the change empty sensor is intact.
Defective change empty sensor. Replace the coin mec.
Defective coin vender control PWB. Replace the coin mec.

Code: 9140
Description: Sensor error in coin vender change (Yen 100)
Change is empty despite change is enough.
Causes: Coin jam in the change tube
Poor contact in the connector.
Defective change empty sensor.
Defective coin vender control PWB.
Remedy: Coin jam in the change tube Check visually and remedy.
Poor contact in the connector. Check if the change empty sensor is intact.
Defective change empty sensor. Replace the coin mec.
Defective coin vender control PWB. Replace the coin mec.

Code: 9150
Description: Sensor error in coin vender change (Yen 500)
Change is empty despite change is enough.
Causes: Coin jam in the change tube
Poor contact in the connector.
Defective change empty sensor.
Defective coin vender control PWB.
Remedy: Coin jam in the change tube Check visually and remedy.
Poor contact in the connector. Check if the change empty sensor is intact.
Defective change empty sensor. Replace the coin mec.
Defective coin vender control PWB. Replace the coin mec.

Code: 9160
Description: Coin vender pay-out error
Coin is paid out despite the pay-out motor is determined not active.
Causes: Defective pay-out motor.
Remedy: Replace the coin mec.

Code: 9170
Description: Coin vender pay-out sensor error
Coin is paid out despite the pay-out motor is determined not active.
Causes: Change jam at the pay-out.
Defective pay-out motor.
Defective pay-out sensor.
Remedy: Change jam at the pay-out. Check visually and remedy.
Defective pay-out motor. Replace the coin mec.
Defective pay-out sensor. Replace the coin mec.

Code: 9200
Description: DP multi feed sensor communication error
A communication error is detected 3 times in succession.
Causes: Defective connector cable or poor contact in the connector.
Defective PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DP main PWB (YC1) and ISC PWB (YC12) ISC PWB (YC3) and main PWB (YC11)
Defective PWB. Replace the DP main PWB or the ISC PWB and check for correct operation.

Code: 9210
Description: DP multi feed sensor error
The DP multi feed sensor has signaled the presence of paper for 10 ms continuously.
Causes: Defective connector cable or poor contact in the connector.
Defective DP multi feed sensor.
Defective DP main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DP multi feed sensor and DP main PWB (YC11)
Defective DP multi feed sensor. Replace the DP multi feed sensor.
Defective DP main PWB. Replace the DP main PWB and check for correct operation.

Code: 9220
Description: DP multi feed sensor backup error
When writing the data, read and write data does not match 3 times in succession.
Causes: Defective connector cable or poor contact in the connector.
Defective DP multi feed sensor.
Defective DP main PWB.
Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. DP multi feed sensor and DP main PWB (YC11)
Defective DP multi feed sensor. Replace the DP multi feed sensor.
Defective DP main PWB. Replace the DP main PWB and check for correct operation.

Code: 9500, 9510, 9520
Description: Contact the Service Administrative Division.
Causes:
Remedy: Contact the Service Administrative Division.

Code: F000
Description: Communication error between main PWB and operation PWB
Causes: Defective main PWB.
Defective operation PWB.
Remedy: Defective main PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.
Defective operation PWB. Replace the operation PWB and check for correct operation.

Code: F010
Description: Main PWB checksum error
Causes: Defective main PWB.
Remedy: Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.

Code: F040
Description: Communication error between main PWB and print engine
Causes: Defective main PWB.
Defective engine PWB.
Remedy: Defective main PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: F041
Description: Communication error between main PWB and scanner engine
Causes: Defective main PWB.
Defective ISC PWB.
Remedy: Defective main PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.
Defective ISC PWB. Replace the ISC PWB and check for correct operation.

Code: F050
Description: Print engine ROM checksum error
Causes: Defective engine PWB.
Remedy: Defective engine software. Install the engine software.
Defective engine PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace engine PWB.

Code: F051
Description: Scanner engine ROM checksum error
Causes: Defective ISC PWB.
Remedy: Defective Scanner software. Install the Scanner software.
Defective ISC PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace ISC PWB.

Code: F278
Description: Power supply in drive system error
Causes: Main power switch was turned off without using the power key, or a power failure has occurred.
Remedy: Turn on power. (To switch off power, first press the power key until the main power indicator goes off, then turn the main power switch off.)

Источник

C0030
Системная ошибка в управлении факсом
Обработка при помощи программного обеспечения факса была отключена из за проблем с оборудованием
Неисправность в системе управления факсом PWB
Заменить систему управления факсом PWB

C0070
Обнаружена несовместимость платы управления PWB
Обнаружена несовместимость при первичной инициализации системы управления факсом PWB. Никакие команды связи не проходят.
Дефект программного обеспечения факса
Установить программное обеспечение для факса

C0100
Ошибка при резервном копировании памяти устройства

Неисправна флеш память
Заменить плату управления PWB

C0120
Ошибка данных MAC адреса

Неисправность в плате управления PWB
Заменить плату управления PWB

C0130
Ошибка чтения/записи при резервном копировании

Неисправна флеш память
Заменить плату управления PWB

C0140
Ошибка при резервном копировании данных

Неисправна флеш память
Заменить плату управления PWB

C0150
Ошибка EEPROM платы управления PWB
Обнаружена ошибка связи PWB EEPROM (U17)
Неправильная установка PWB EEPROM (U17)
Проверить установку EEPROM (U17) и при необходимости исправить

C0170
Ошибка счетчика

1. Неисправность control PWB.

2. Повреждения данных PWB EEPROM (U17)

1. Заменить плату управления PWB.

2. Обратиться в сервис обслуживания

C0180
Номер аппарата не совпадает
Основной номер и номер двигателя не совпадают
1. Основная PWB или PWB двигателя была заменена.

2. Повреждения данных PWB EEPROM (U17)

1. U004 Задать номер.

2. Обратиться в сервис обслуживания

2. Повреждение провода между платой PWB (YC30) и интерфесным разъемом устройства подачи, либо разъем подключен неправильно.

3. Неисправен кабель между PF основной PWB и подачей бумаги, либо разъем не вставлен. Плата PF неисправна.

4. Неисправность control PWB

1. Еще раз внимательно прочитайте инструкцию по установке.

2. Убедитесь, что разъем подключен, а кабель не поврежден. При необходимости — замените.

3. Убедитесь, что разъем подключен, а кабель не поврежден.Заменить печатную плату.

4. Заменить плату управления PWB.

C0830
Ошибка контрольной суммы прошивки FAX control PWB
Произошла ошибка контрольной суммы программы управления FAX control PWB
1. Дефект программного обеспечения факса.

2. Неисправность в системе управления факсом PWB

1. Установить программное обеспечение для факса.

2. Заменить плату управления факсом PWB

C0840
Неисправность RTС
Расхождение во времени между RTC и текущим пять и более лет.
1. Неисправность control PWB

2. Отсоединена батарея.

1. Заменить плату управления PWB.

2. Визуально проверить и при необходимости исправить.

C0870
Проблема передачи данных большой емкости между FAX control PWB и control PWB
Не выполняется передача данных между FAX control PWB и control PWB, даже при повторе через заданный промежуток
Неправильная установка FAX control PWB

Переставить FAX control PWB

C0920
Ошибка файловой системы факса
Резервное копирование данных не производится по причине ошибки файловой системы флеш-памяти
Неисправность в системе управления факсом PWB
Заменить плату управления факсом PWB

2. Неисправен привод основного двигателя.

3. Неисправен двигатель.

4. Неисправность control PWB

1. Вставьте разъем. Проверьте целостность кабеля.

2. Проверьте плавность вращения роликов и шестерней. При необходимости смажьте. Убедитесь в отсутсвии разрывов передач.

3. Заменить.

4. Заменить.

C2610
Ошибка дигателя устройства подачи бумаги
Двигатель устройства подачи бумаги лотка 2 не выходит на готовность более чем через 2 секунды после включения.
Неисправность кабеля между двигателем устройства подачи бумаги и control PWB (YC4).
Вставьте разъем. Проверьте целостность кабеля (Обратитесь к инструкции)

C2620
Ошибка дигателя устройства подачи бумаги
Двигатель устройства подачи бумаги лотка 3 не выходит на готовность более чем через 2 секунды после включения.
Неисправность кабеля между двигателем устройства подачи бумаги и control PWB (YC4).
Вставьте разъем. Проверьте целостность кабеля (Обратитесь к инструкции)

C3100
Ошибка исходного положения ISU

1. Неисправность FFC между CCD PWB (YC1) и control PWB (YC8).

2. Неисправность FFC между control PWB (YC6) и сканера WPB (YC103) или неправильная установка FCC.

3. Неисправность датчика исходного положения.

4. Неисправность кабеля между двигателем ISU и сканером PWB (YC104) или разъем вставлен неправильно.

1. Заменить блок сканера ISU

2. Переставить FFC. Проверить на разрыв, при необходимости заменить.

3. Заменить датчик.

4. Вставьте разъем. Проверьте целостность кабеля.

C3200
Ошибка лампы экспозиции
Лампа экспозиции не включается
1. Повреждения FFC между сканером PWB (YC103) и control PWB (YC6), либо некорректная установка FFC.

2. Повреждения FFC между CCD PWB (YC1) и control PWB (YC8).

3. Неисправен кабель между CCD PWB (YC3) и LED приводом PWB (YC1) либо разъем не подключен.

4. Неисправен кабель между LED приводом PWB (YC2) и лампой экспонирования.

5. Лампа экспонирования вышла из строя.

6. Неисправен светодиодный привод.

1. Переустановите FFC. Проверьте целостность, при необходимости замените.

2. Заменить блок сканера.

3. Убедитесь, что разъем подключен, а кабель не поврежден. При необходимости — замените.

4. Убедитесь, что разъем подключен, а кабель не поврежден. При необходимости — замените.

5. Заменить лампу.

6. Заменить привод.

C3300
Ошибка AGC

1. Повреждения FFC между CCD PWB (YC1) и control PWB (YC8).

2. Лампа экспонирования вышла из строя.

3. Неисправность CCD PWB

4. Неисправность control PWB

1. Заменить блок сканера.

2. Заменить лампу.

3. Заменить CCD PWB

4. Заменить control PWB

C3500
Ошибка связи CPU — ASIC (CCD PWB)
Обнаружен код ошибки
1. Повреждения FFC между CCD PWB (YC1) и control PWB (YC8).

2. Неисправность CCD PWB.

3. Неисправность control PWB

1. Заменить блок сканера (ISU).

2. Заменить CCD PWB

3. Заменить control PWB

2. Неисправен блок лазерного сканера.

3. Неисправность control PWB

1. Убедитесь, что разъем подключен, а кабель не поврежден. При необходимости — замените.

2. Заменить блок сканера.

3. Заменить control PWB

C4200
Ошибка BD (блока лазерного сканера)

1. BD датчик не обнаруживает лазерный луч из-за скопления конденсата на зеркале.

2. Неисправен блок лазерного сканера.

1. Выключите питание машины минимум на 30 минут, затем снова включите, если это не помогает необходимо менять блок сканера.

2. Заменить блок сканера.

C6000
Выход из строя термо-элемента (фьюзера)
Температура фьюзера не поднимается после включения устройства.
1. Плохой контакт клемм термистора фьюзера.

2. Плохой контакт в местах подключения нагревателя термоблока.

3. Термисторы фьюзера установлены неправильно.

4 . Срабатывает термореле

5. Нагреватель фьюзера установлен неправильно

6. Выход из строя термо-элемента

1. Проверьте контакты.

2. Проверьте контакты.

3. Заменить блок закрепления

4. Заменить блок закрепления

5. Заменить блок закрепления

6. Заменить блок закрепления

C6020
Слишком высокая температура фьюзера
Термистор фьюзера обнаружил аномально высокую температуру.
Пробой термистора фьюзера
Заменить блок закрепления

C6030
Поврежден шлейф термистора термоэлемента
Значени на входе термистора равно 0
1. Плохой контакт в клеммах термистора.

2. Неисправен шлейф термистора

3. Термистор установлен некорректно

4. Срабатывает термореле

Проверить контакты

Заменить блок закрепления

2. Дефект соединения между источником питания PWB (YC103) и PWB высокого напряжения (YC201)

3. Неисправен источник питания PWB

4. Неисправность control PWB

1. Переподключите коннектор.Убедитесь что кабель не поврежден.

2. Переподключите коннектор

3. Заменить источник питания

4. Заменить control PWB

C7990
Бункер отработки переполнен
Датчик тонера обнаружил, что бункер для отработки переполнен
1. Бункер отработки драм-юнита переполнен.

2. Неисправен датчик отработки

3. Неисправность control PWB

1. Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла замените драм-юнит.

2. Замените датчик.

3. Заменить control PWB

4. Очистите драм юнит (инструкция по очистке бункера отработанного тонера)

F000
Ошибка связи control PWB — панель управления PWB

1. Неисправность соединения панели управления PWB (YC1) и control PWB (YC7).

2. Неисправность панели управления

3. Неисправность control PWB

1. Переподключите коннектор.Убедитесь что кабель не поврежден.

2. Замените панель.

3. Заменить control PWB

F020
Ошибка контрольной суммы RAM control PWB

1. Неисправность основной микросхемы памяти (ОЗУ) на главной плате управления PWB

2. Неисправность платы расширения памяти (DIMM)

1. Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла, замените control PWB

2. Замените плату расширения (DIMM)

F040
Ошибка связи control PWB двигателя
Обнаружена ошибка связи
Неисправность control PWB
Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла, замените control PWB

F041
Ошибка связи между гланой платой управления и платой управления сканером
Обнаружена ошибка связи
Неисправна главная плата управления или управления сканером
Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла, замените control PWB или scanner PWB

F050
Ошибка контрольной суммы платы управления двигателем

1. Такие ошибки могут происходить при обновлении прошивки control PWB

2. Неисправность control PWB

1. Скачайте прошивку снова

2. Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла, замените control PWB

F186
Ошибка управления видеоданными главной панели управления

Неисправность control PWB
Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла, замените control PWB

Содержание

1 Самые распространенные коды ошибок принтеров Kyocera
2 Код C7990
3 Способ №2. Замена чипа
4 Другие неисправности
5 Способ №1. Сброс счетчика страниц / тонера
6 Сброс ошибок у принтеров Kyocera своими руками
7 Способы решения проблемы
- 7.1 Сброс сообщения о неоригинальном тонере на Kyocera fs 1040
8
9
10
11
12
13
14 Значения мигания индикаторов

Слово «ошибка» на английском языке будет «ошибка», поэтому большинство кодов начинаются с заглавной E.

Итак, какие ошибки могут возникать в принтерах Kyocera FS 1020MFP японского производства:

1.E-0002. Указывает, что картридж с тонером не подходит для региональных спецификаций. Вам нужно использовать другой картридж.
2.E-0003. Эта ошибка указывает на то, что память сканера заполнена. Будут доступны только самые последние отсканированные изображения. Чтобы сбросить ошибку E-0003, необходимо очистить память сканера. Для этого нажмите Стоп / Сброс.

Стирание памяти

3.E-0007. Значит, для печати не хватает чернил. Исправить код 07 просто — нужно добавить тонер.
4. При открытой задней или передней крышке МФУ Kyocera не работает и выдает код ошибки E-0008.
5. После печати или копирования большого количества бумаги (сто листов), если лоток не опорожняется, отображается сообщение об ошибке принтера Kyocera E-0009. Вам нужно удалить листы и нажать кнопку Старт, чтобы продолжить работу.
6. Иногда выдается код E-0012, что означает, что задача не может быть выполнена из-за нехватки оперативной памяти. Для решения этой проблемы необходимо изменить разрешение печати с 1200 на 600. Порядок действий описан в инструкции.
7. Когда появится код E-0014, загрузите бумагу нужного формата во входной лоток. Размер листов определяется драйвером принтера.
8. Если вы забыли подключить сетевой или USB-кабель, принтер отобразит код ошибки E-0015. Нужно нажать Stop / Reset, подключить кабель и снова нажать эту кнопку.

Замена картриджа с тонером

В японских принтерах Kyocera FS 1020MFP могут возникать ошибки, как описанные в предыдущем разделе, так и конкретные ошибки. Все коды можно найти в инструкции по эксплуатации.

Код C7990

Этот номер ошибки на моделях FS 1020MFP указывает на сигнал о переполнении тонера.

Ошибка C7990

Причин возникновения ошибки C7990 может быть три:

• неисправна плата PWB;
• неисправен датчик количества краски;
• бункер действительно полон — рекомендуется заменить барабан.

Барабан

В первых двух случаях необходимо обратиться в сервисный центр.

В третьем случае появления кода C7990, если ресурс барабана еще не исчерпан, можно очистить бункер для краски. Делают они это так:

1. Откройте переднюю крышку и выньте блок проявки.
2. Подойдите к барабану.
3. Осторожно откройте крышку бункера и удалите краску.
4. Соберите прибор в обратном порядке.

Как видите, ошибку принтера Kyocera C7990 легко устранить самостоятельно, а обращаться к специалистам нужно только тогда, когда карты действительно плохие.

Способ №2. Замена чипа

Альтернативный вариант сброса счетчика вручную — замена микросхемы. Вы можете заправлять картридж принтера KyoceraFS-1040 сколько угодно, но благодаря установке нового защитного чипа устройство не распознает замену расходного материала.

Ошибочно многие пользователи считают неисправностью, когда на корпусе принтера Kuoser 1040 горит красная кнопка с сообщением «Внимание» и принтер не печатает присланные ему документы. В этом материале мы рассмотрим, в каких случаях это происходит, что делать, как быстро все отремонтировать в домашних условиях, не обращаясь в сервисный центр. Инструкции применимы ко многим моделям Kyocera. Например, fs1040 взят из-за его популярности.

Другие неисправности

Также возможно появление таких кодов:

• C-F040. Вам нужно выключить и снова включить устройство, нажав кнопку питания.
• J-0511. Код указывает на то, что бумага застряла под задней крышкой. Инструкции описывают, как удалить бумагу в соответствующем разделе.
• ПФ. Принтер предложит вам добавить бумагу во входной лоток.

Как видите, принтеры японской компании Kyocera выходят из строя редко. Чаще всего ошибки возникают из-за неправильных или неосторожных действий. Вы можете исправить их самостоятельно, но если не уверены в своих силах, лучше проконсультироваться со специалистом.

Способ №1. Сброс счетчика страниц / тонера

Чтобы запустить принтер KyoceraFS-1040, просто сбросьте счетчик страниц / тонера, удерживая нажатыми кнопки «Отмена» и «GO».

Единственная проблема заключается в том, что удаление предупреждения принтера об использовании неоригинального картриджа может привести к аннулированию гарантии. Так как устройство записывает абсолютно все ошибки в «Журнал событий».

Сброс ошибок у принтеров Kyocera своими руками

Сбрасывая ошибки в принтерах Kyocera, необходимо понимать ряд мер, которые опытный пользователь может потенциально предпринять для восстановления и запуска печатающих устройств без обращения в сервисный центр.

Ошибка №

Это вызывает

Решение

E-0001

В принтер установлен совместимый картридж или повреждена микросхема расходных материалов. Проблему можно решить несколькими способами:

1 установите оригинальный картридж;

2 замена поврежденного чипа;

3 прошивки принтера — так что любой картридж можно устанавливать в принтер неограниченное количество раз;

4 сброс ошибки — держать нажатыми несколько секунд кнопки «Режим» и «Сброс».

E-0002

Регион используемого картриджа не соответствует техническим характеристикам принтера. Проблему можно решить несколькими способами:

1. Установите картридж, соответствующий региону принтера;

3 прошивки принтера.

E-0003

Память печатающего устройства заполнена. Распечатайте уже отсканированные документы или сбросьте операцию с помощью соответствующей кнопки.

E-0007

В картридже закончился тонер. Замените картридж на новый, оригинальный, совместимый или заправьте расходный материал.

E-0008

Одна из крышек принтера не закрыта. Закройте переднюю и заднюю крышки принтера до щелчка.

E-0009

Лоток для печати заполнен. Удалите отпечатанную бумагу и возобновите печать, нажав кнопку «Пуск».

E-0012

Память принтера заполнена. Измените разрешение печати до 600 dpi.

E-0014

Установлен формат бумаги, не поддерживаемый принтером. Замените бумагу листами совместимого размера.

Иногда функциональность принтера может быть ограничена на программном уровне.

Для расширения диапазона форматов рекомендуется обновить программное обеспечение печатающего устройства.

E-0015

1. В принтере нет питания.

2. Сетевой кабель не подключен.

3. На ПК нет драйверов. Проверьте целостность сетевого кабеля.

При необходимости установите драйвер.

E-0018

Выбранный файл отсутствует в очереди печати. Сбросьте операцию, нажав кнопку «Сброс». Затем выберите новый файл и продолжите печать.

E-0019

Формат печати не поддерживается принтером. Сбросьте операцию, нажав кнопку «Сброс».

J-0511

Бумага замята. Осторожно удалите оставшуюся бумагу из корпуса принтера.

ПФ

Во входном лотке нет бумаги. Загрузите бумагу во входной лоток и возобновите печать, нажав кнопку «Пуск».

Способы решения проблемы

Сброс сообщения о неоригинальном тонере на Kyocera fs 1040

Если вышеперечисленные варианты не сработали, то, скорее всего, проблема в самом картридже. Дело в том, что он оснащен датчиком уровня тонера и чипом, отслеживающим количество отпечатанных листов. Когда расходный материал заканчивается или, согласно чипу, он должен закончиться, печать блокируется до тех пор, пока он не будет заменен новым картриджем. Именно это и произошло в нашей ситуации.

Есть три варианта решения проблемы:

Купите новый картридж и продолжайте его печатать. Это недешево.
После каждой пополнения порошка следует заменять чип, который начнет отсчет количества распечатанных документов с нуля.
Сбросить счетчик на микросхеме. Сделать это несложно, но делать это нужно каждый раз при включении устройства.

Инструкции по сбросу:

Включите устройство.
Подождите, пока двигатель остановится и красный свет не начнет мигать.
Одновременно нажмите кнопки «Пуск» и «Отмена» на 5-7 секунд».
Нажмите и удерживайте, пока красный и зеленый не начнут мигать по очереди.
Ждем завершения процесса.
Пытаюсь распечатать.

Значения мигания индикаторов

Ничего не горит и уведомлений нет, значит, устройство полностью готово к работе.
Медленное мигание кнопки означает, что в лотке нет бумаги или в картридже низкий уровень пыли.
Индикатор мигает быстрее: внутри устройства застрял лист бумаги, лоток окончательной обработки заполнен, и распечатки невозможно вставить, вся память принтера заполнена и используются неоригинальные расходные материалы.
Индикатор горит и не гаснет. Проверьте, закрыты ли крышки. Тонер для печати, возможно, уже закончился.

Если у вас возникли трудности с определением причин появления сообщения «Внимание», вы можете воспользоваться специальным программным обеспечением от инженеров компании — «Kyocera Client Tool». Эта утилита поможет вам более точно диагностировать проблему. Вы можете найти его на сайте компании или на диске с драйверами принтера.

Источники

http://printergid.ru/neispravnosti/oshibki-kyocera
https://dudom.ru/kompjutery/kyocera-1040-indikacija-oshibok/
https://window-10.ru/ecosys-fs-1020mfp-oshibka-e7/

[свернуть]

Источник

Содержание

1 Самые распространенные коды ошибок принтеров Kyocera
2 Код C7990
3 Способ №2. Замена чипа
4 Другие неисправности
5 Способ №1. Сброс счетчика страниц / тонера
6 Сброс ошибок у принтеров Kyocera своими руками
7 Способы решения проблемы
- 7.1 Сброс сообщения о неоригинальном тонере на Kyocera fs 1040
8
9
10
11
12
13
14 Значения мигания индикаторов

Слово «ошибка» на английском языке будет «ошибка», поэтому большинство кодов начинаются с заглавной E.

Итак, какие ошибки могут возникать в принтерах Kyocera FS 1020MFP японского производства:

Стирание памяти

Замена картриджа с тонером

Код C7990

Этот номер ошибки на моделях FS 1020MFP указывает на сигнал о переполнении тонера.

Ошибка C7990

Причин возникновения ошибки C7990 может быть три:

Барабан

В первых двух случаях необходимо обратиться в сервисный центр.

Способ №2. Замена чипа

Другие неисправности

Также возможно появление таких кодов:

Способ №1. Сброс счетчика страниц / тонера

Сброс ошибок у принтеров Kyocera своими руками

Ошибка №

Это вызывает

Решение

E-0001

1 установите оригинальный картридж;

2 замена поврежденного чипа;

3 прошивки принтера — так что любой картридж можно устанавливать в принтер неограниченное количество раз;

4 сброс ошибки — держать нажатыми несколько секунд кнопки «Режим» и «Сброс».

E-0002

1. Установите картридж, соответствующий региону принтера;

3 прошивки принтера.

E-0003

E-0007

E-0008

Одна из крышек принтера не закрыта. Закройте переднюю и заднюю крышки принтера до щелчка.

E-0009

Лоток для печати заполнен. Удалите отпечатанную бумагу и возобновите печать, нажав кнопку «Пуск».

E-0012

Память принтера заполнена. Измените разрешение печати до 600 dpi.

E-0014

Установлен формат бумаги, не поддерживаемый принтером. Замените бумагу листами совместимого размера.

Иногда функциональность принтера может быть ограничена на программном уровне.

Для расширения диапазона форматов рекомендуется обновить программное обеспечение печатающего устройства.

E-0015

1. В принтере нет питания.

2. Сетевой кабель не подключен.

3. На ПК нет драйверов. Проверьте целостность сетевого кабеля.

При необходимости установите драйвер.

E-0018

E-0019

Формат печати не поддерживается принтером. Сбросьте операцию, нажав кнопку «Сброс».

J-0511

Бумага замята. Осторожно удалите оставшуюся бумагу из корпуса принтера.

ПФ

Во входном лотке нет бумаги. Загрузите бумагу во входной лоток и возобновите печать, нажав кнопку «Пуск».

Способы решения проблемы

Сброс сообщения о неоригинальном тонере на Kyocera fs 1040

Есть три варианта решения проблемы:

Купите новый картридж и продолжайте его печатать. Это недешево.
После каждой пополнения порошка следует заменять чип, который начнет отсчет количества распечатанных документов с нуля.
Сбросить счетчик на микросхеме. Сделать это несложно, но делать это нужно каждый раз при включении устройства.

Инструкции по сбросу:

Включите устройство.
Подождите, пока двигатель остановится и красный свет не начнет мигать.
Одновременно нажмите кнопки «Пуск» и «Отмена» на 5-7 секунд».
Нажмите и удерживайте, пока красный и зеленый не начнут мигать по очереди.
Ждем завершения процесса.
Пытаюсь распечатать.

Значения мигания индикаторов

Ничего не горит и уведомлений нет, значит, устройство полностью готово к работе.
Медленное мигание кнопки означает, что в лотке нет бумаги или в картридже низкий уровень пыли.
Индикатор мигает быстрее: внутри устройства застрял лист бумаги, лоток окончательной обработки заполнен, и распечатки невозможно вставить, вся память принтера заполнена и используются неоригинальные расходные материалы.
Индикатор горит и не гаснет. Проверьте, закрыты ли крышки. Тонер для печати, возможно, уже закончился.

Источники

http://printergid.ru/neispravnosti/oshibki-kyocera
https://dudom.ru/kompjutery/kyocera-1040-indikacija-oshibok/
https://window-10.ru/ecosys-fs-1020mfp-oshibka-e7/

[свернуть]

Если с аппаратом Kyocera TASKalfa 1800, Kyocera TASKalfa 2200 произошла проблема, откроется следующий экран с уведомлением.
• Индикатор [Внимание] на панели управления горит или мигает.
• На дисплее сообщений панели управления аппарата появилось сообщение об ошибке.

Если индикатор [Внимание] горит или мигает и на дисплее сообщений панели управления аппарата появилось сообщение об ошибке, проверьте KYOCERA Client Tool или Монитор состояния.

ПРИМЕЧАНИЕ Если индикаторы постоянно горят и мигают не так, как описано выше, вероятно, произошла ошибка службы. Выключите питание, отсоедините шнур питания и вставьте его обратно, после чего включите питание. Это может помочь сбросить ошибку. Если ошибка не исчезает, свяжитесь со своим представителем сервисной службы (тел. в Минске +375 17 291-28-24)

Ниже описаны неполадки, которые не могут быть устранены пользователем

Дисплей сообщений	Описание	Меры устранения
Бункер отраб тонера перепол. или не уст.	Бункер для отработанного тонера установлен неправильно	Установите Бункер для отработанного тонера должным образом
Бункер для отработанного тонера заполнен	Замените бункер отработанного тонера
Встряхните картр. с тонером	Тонер слежался	Откройте переднюю крышку аппарата и вытяните контейнер с тонером. Сильно встряхните контейнер с тонером и установите его на место
Вызовите сервисный персонал.	В аппарате произошла ошибка	Обратите внимание на код ошибки, отображаемый в дисплее сообщений, и свяжитесь с представителем сервисной службы (тел. в Минске +375 17 291-28-24)
Выньте бумагу с внутреннего лотка		Извлеките бумагу из внутреннего лотка. Нажмите клавишу [OK], чтобы возобновить печать
Добавьте тонер	Закончился тонер	Замените контейнер с тонером TK-4105
Загрузите бумагу в кассету #	↑↓ (отображается попеременно) A4 (формат бумаги) Обычная (тип носителя) OK: Перейдите к следующему шагу	Загрузите бумагу. Нажмите клавишу [OK] и перейдите к следующему шагу. • Для выбора другого устройства подачи выберите [Выберите бумагу]. • Для печати на бумаге, в настоящее время находящейся в устройстве подачи, выберите [Продолж. без изм.]
Загрузите бумагу в универсальный лоток	↑↓ (отображается попеременно) A4 (формат бумаги) Обычная (тип носителя) OK: Перейдите к следующему шагу	Загрузите бумагу. Нажмите клавишу [OK] и перейдите к следующему шагу. • Для выбора другого устройства подачи выберите [Выберите бумагу]. • Для печати на бумаге, в настоящее время находящейся в устройстве подачи, выберите [Продолж. без изм.]
Закройте автоподатчик оригиналов	Открыт автоподатчик оригиналов	Откройте и закройте автоподатчик оригиналов
Закройте крышку автопод. оригиналов	Открыта верхняя крышка автоподатчика оригиналов	Откройте и закройте крышку автоподатчика оригинало
Закройте переднюю крышку	Открыта передняя крышка	Откройте и закройте переднюю крышку
Закройте правую крышку #	Открыта какая-либо крышка	Откройте и закройте крышку, обозначенную на экране
Замятие бумаги. (DP) ↑↓ (отображается попеременно) Проверьте (B)(C) в крышке DP	В автоподатчике произошло замятие бумаги.	См. Устранение замятия бумаги в Руководстве по эксплуатации и извлеките замятую бумагу
Замените МК	Необходимо производить замену деталей комплекта техобслуживания MK-4105 (ремкомплекта) каждые 150 000 страниц печати.	Данная операция должна производиться специалистом. Обратитесь к представителю сервисной службы (тел. в Минске +375 17 291-28-24)
Замятие	Произошло замятие бумаги в кассете или универсальном лотке	См. Устранение замятия бумаги и извлеките замятую бумагу
Извлеките оригиналы из автоподатчика	Для продолжения работы необходимо извлечь оригиналы из автоподатчика оригиналов	Извлеките оригиналы из автоподатчика оригиналов
Кабель USB был отключен	Кабель USB не подключен	Нажмите клавишу [OK] и подключите кабель USB
ПК выключен	Нажмите клавишу [OK] и включите ПК
Не удается найти KYOCERA Client Tool	Нажмите клавишу [OK] и откройте KYOCERA Client Tool на ПК
Макс. к-во сканируемых страниц	Превышен предел сканирования	Дальнейшее сканирование невозможно. Задание отменено. Нажмите клавишу [OK]
Мало тонера. (Зам., когда законч.)	Скоро понадобится заменить контейнер с тонером	Получите новый контейнер с тонером TK-4105. Внимание! Когда заканчивается тонер аппарат перестает печатать
Не оригинальный тонер	Установлен контейнер с тонером не марки Kyocera	Производитель не несет ответственности за повреждения, вызванные использованием неоригинального тонера. Мы рекомендуем использовать исключительно оригинальные контейнеры с тонером TK-4105. . Если нужно использовать установленный в настоящее время контейнер с тонером, нажмите *одновременно* и удерживайте клавиши [OK] и [Стоп] в течение не менее 3 с.
Неверный ид. уч. зап. Задание отменено	Указан неверный идентификатор учетной записи при внешней обработке задания. Задание отменено	Нажмите клавишу [OK]
Невозможна двусторонняя печать на этой бумаге	Не возможна печать на бумаге выбранного формата или типа	Нажмите клавишу [OK] и перейдите к следующему шагу: • Для выбора другого устройства подачи выберите пункт [Выберите бумагу]. • Чтобы печатать, не используя функцию двусторонней печати, выберите пункт [Продолж. без изм.].
Недостаточно памяти. Невозможно начать выполнение задания	Невозможно начать выполнение задания	Повторите попытку позже
Ограничено алгоритмом учета заданий(Печать)	Задание отменено, поскольку его выполнение ограничено функцией учета заданий	Нажмите клавишу [OK]
Ограничено алгоритмом учета заданий(Сканер)	Задание отменено, поскольку его выполнение ограничено функцией учета заданий	Нажмите клавишу [OK]
Очистите сканер	Произошло загрязнение сканера	Очистите щелевое стекло с помощью чистящей салфетки, поставляемой вместе с автоподатчиком оригиналов.
Ошибка. Выключить	—	Отключите и снова включите аппарат с помощью выключателя питания
Память переполнена	Невозможно продолжить выполнение задания из-за отсутствия свободной памяти	Измените разрешение печати с Быстр1200 до 600 dpi. См. Printer Driver User Guide
Память сканера переполнена	Дальнейшее сканирование невозможно из-за нехватки памяти сканера.	Для отмены задания нажмите [OK]
Перезагрузка печати. Задание отменено	Предупреждение. Недостаточно памяти принтера. Задание отменено	Нажмите клавишу [OK]
Превышено ограничение учета заданий	Превышено число распечаток из-за ограничения алгоритмом учета заданий. Достигнут предел печати	Это задание отменено. Нажмите клавишу [OK]
Уст.другую кассету	Выбрано «Сдвиг»	Для использования сдвига необходимо загрузить в другой лоток бумагу такого же формата, что и в выбранном устройстве подачи, но в другой ориентации
Установите все оригиналы обратно и нажмите клавишу [Старт].	Возникает при печати двусторонних документов в режиме ручной двусторонней печати	Извлеките оригиналы из автоподатчика оригиналов, расположите их в первоначальном порядке и положите обратно. Нажмите клавишу [OK], чтобы возобновить печать. Для отмены задания нажмите [Стоп]
Установлен неизвестный тонер. ПК	Региональная спецификация контейнера с тонером не соответствует спецификации аппарата	Установите оригинальный контейнер с тонером Замените контейнер с тонером TK-4105

C0100
Ошибка при резервном копировании памяти устройства

Неисправна флеш память
Заменить плату управления PWB

C0120
Ошибка данных MAC адреса

Неисправность в плате управления PWB
Заменить плату управления PWB

C0130
Ошибка чтения/записи при резервном копировании

Неисправна флеш память
Заменить плату управления PWB

C0140
Ошибка при резервном копировании данных

Неисправна флеш память
Заменить плату управления PWB

C0170
Ошибка счетчика

1. Неисправность control PWB.2. Повреждения данных PWB EEPROM (U17)
1. Заменить плату управления PWB.2. Обратиться в сервис обслуживания

C0180
Номер аппарата не совпадает
Основной номер и номер двигателя не совпадают
1. Основная PWB или PWB двигателя была заменена.2. Повреждения данных PWB EEPROM (U17)
1. U004 Задать номер. 2. Обратиться в сервис обслуживания

C0420
Ошибка связи с системой подачи бумаги
Ошибка коммуникации между платой PWB и дополнительным устройством подачи бумаги
1. Неправильная установка устройства подачи бумаги2. Повреждение провода между платой PWB (YC30) и интерфесным разъемом устройства подачи, либо разъем подключен неправильно.3. Неисправен кабель между PF основной PWB и подачей бумаги, либо разъем не вставлен. Плата PF неисправна.4. Неисправность control PWB
1. Еще раз внимательно прочитайте инструкцию по установке.2. Убедитесь, что разъем подключен, а кабель не поврежден. При необходимости — замените.3. Убедитесь, что разъем подключен, а кабель не поврежден.Заменить печатную плату.4. Заменить плату управления PWB.

C0830
Ошибка контрольной суммы прошивки FAX control PWB
Произошла ошибка контрольной суммы программы управления FAX control PWB
1. Дефект программного обеспечения факса. 2. Неисправность в системе управления факсом PWB
1. Установить программное обеспечение для факса.2. Заменить плату управления факсом PWB

C0840
Неисправность RTС
Расхождение во времени между RTC и текущим пять и более лет.
1. Неисправность control PWB 2. Отсоединена батарея.
1. Заменить плату управления PWB.2. Визуально проверить и при необходимости исправить.

C2000
Ошибка главного двигателя
Главный двигатель не выходит на готовность в течение 2 секунд после включения
1. Неисправен кабель между основным двигателем (CN1) и платой PWB (YC17) или разъем вставлен неправильно. 2. Неисправен привод основного двигателя. 3. Неисправен двигатель.4. Неисправность control PWB
1. Вставьте разъем. Проверьте целостность кабеля.2. Проверьте плавность вращения роликов и шестерней. При необходимости смажьте. Убедитесь в отсутсвии разрывов передач.3. Заменить.4. Заменить.

C3100
Ошибка исходного положения ISU

1. Неисправность FFC между CCD PWB (YC1) и control PWB (YC8).2. Неисправность FFC между control PWB (YC6) и сканера WPB (YC103) или неправильная установка FCC.3. Неисправность датчика исходного положения.4. Неисправность кабеля между двигателем ISU и сканером PWB (YC104) или разъем вставлен неправильно.
1. Заменить блок сканера ISU 2. Переставить FFC. Проверить на разрыв, при необходимости заменить. 3. Заменить датчик. 4. Вставьте разъем. Проверьте целостность кабеля.

C3200
Ошибка лампы экспозиции
Лампа экспозиции не включается
1. Повреждения FFC между сканером PWB (YC103) и control PWB (YC6), либо некорректная установка FFC.2. Повреждения FFC между CCD PWB (YC1) и control PWB (YC8).3. Неисправен кабель между CCD PWB (YC3) и LED приводом PWB (YC1) либо разъем не подключен.4. Неисправен кабель между LED приводом PWB (YC2) и лампой экспонирования.5. Лампа экспонирования вышла из строя.6. Неисправен светодиодный привод.
1. Переустановите FFC. Проверьте целостность, при необходимости замените. 2. Заменить блок сканера.3. Убедитесь, что разъем подключен, а кабель не поврежден. При необходимости — замените.4. Убедитесь, что разъем подключен, а кабель не поврежден. При необходимости — замените.5. Заменить лампу.6. Заменить привод.

C3300
Ошибка AGC

1. Повреждения FFC между CCD PWB (YC1) и control PWB (YC8).2. Лампа экспонирования вышла из строя.3. Неисправность CCD PWB4. Неисправность control PWB
1. Заменить блок сканера. 2. Заменить лампу. 3. Заменить CCD PWB4. Заменить control PWB

C3500
Ошибка связи CPU — ASIC (CCD PWB)
Обнаружен код ошибки
1. Повреждения FFC между CCD PWB (YC1) и control PWB (YC8).2. Неисправность CCD PWB.3. Неисправность control PWB
1. Заменить блок сканера (ISU).2. Заменить CCD PWB3. Заменить control PWB

C4000
Ошибка полигон-мотора (блока лазерного сканера)
Полигон-мотор не выходит на готовность после 6 секунд после включения.
1. Поврежден кабель между полигон-мотором и control PWB (YC10) или разъем не вставлен.2. Неисправен блок лазерного сканера.3. Неисправность control PWB
1. Убедитесь, что разъем подключен, а кабель не поврежден. При необходимости — замените.2. Заменить блок сканера.3. Заменить control PWB

C4200
Ошибка BD (блока лазерного сканера)

1. BD датчик не обнаруживает лазерный луч из-за скопления конденсата на зеркале.2. Неисправен блок лазерного сканера.
1. Выключите питание машины минимум на 30 минут, затем снова включите, если это не помогает необходимо менять блок сканера.2. Заменить блок сканера.

C6000
Выход из строя термо-элемента (фьюзера)
Температура фьюзера не поднимается после включения устройства.
1. Плохой контакт клемм термистора фьюзера.2. Плохой контакт в местах подключения нагревателя термоблока.3. Термисторы фьюзера установлены неправильно.4 . Срабатывает термореле5. Нагреватель фьюзера установлен неправильно6. Выход из строя термо-элемента
1. Проверьте контакты. 2. Проверьте контакты.3. Заменить блок закрепления 4. Заменить блок закрепления 5. Заменить блок закрепления 6. Заменить блок закрепления

C6030
Поврежден шлейф термистора термоэлемента
Значени на входе термистора равно 0
1. Плохой контакт в клеммах термистора.2. Неисправен шлейф термистора3. Термистор установлен некорректно4. Срабатывает термореле
Проверить контакты Заменить блок закрепления

C6400
Ошибка пересечения нуля
Сигнал пересечения нуля не достигает контрольной платы за указанное время
1. Неисправен кабель между PWB высокого напряжения(YC202) и control PWB (YC23) или разъем не вставлен2. Дефект соединения между источником питания PWB (YC103) и PWB высокого напряжения (YC201)3. Неисправен источник питания PWB4. Неисправность control PWB
1. Переподключите коннектор.Убедитесь что кабель не поврежден. 2. Переподключите коннектор 3. Заменить источник питания 4. Заменить control PWB

C7990
Бункер отработки переполнен
Датчик тонера обнаружил, что бункер для отработки переполнен
1. Бункер отработки драм-юнита переполнен.2. Неисправен датчик отработки3. Неисправность control PWB
1. Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла замените драм-юнит.2. Замените датчик.3. Заменить control PWB4. Очистите драм юнит (инструкция по очистке бункера отработанного тонера)

F000
Ошибка связи control PWB — панель управления PWB

1. Неисправность соединения панели управления PWB (YC1) и control PWB (YC7).2. Неисправность панели управления3. Неисправность control PWB
1. Переподключите коннектор.Убедитесь что кабель не поврежден.2. Замените панель.3. Заменить control PWB

F020
Ошибка контрольной суммы RAM control PWB

1. Неисправность основной микросхемы памяти (ОЗУ) на главной плате управления PWB2. Неисправность платы расширения памяти (DIMM)
1. Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла, замените control PWB2. Замените плату расширения (DIMM)

F050
Ошибка контрольной суммы платы управления двигателем

1. Такие ошибки могут происходить при обновлении прошивки control PWB2. Неисправность control PWB
1. Скачайте прошивку снова2. Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла, замените control PWB

F186
Ошибка управления видеоданными главной панели управления

C0100
Ошибка при резервном копировании памяти устройства

Неисправна флеш память
Заменить плату управления PWB

C0120
Ошибка данных MAC адреса

Неисправность в плате управления PWB
Заменить плату управления PWB

C0130
Ошибка чтения/записи при резервном копировании

Неисправна флеш память
Заменить плату управления PWB

C0140
Ошибка при резервном копировании данных

Неисправна флеш память
Заменить плату управления PWB

C0170
Ошибка счетчика

1. Неисправность control PWB.

2. Повреждения данных PWB EEPROM (U17)

1. Заменить плату управления PWB.

2. Обратиться в сервис обслуживания

2. Повреждения данных PWB EEPROM (U17)

1. U004 Задать номер.

2. Обратиться в сервис обслуживания

3. Неисправен кабель между PF основной PWB и подачей бумаги, либо разъем не вставлен. Плата PF неисправна.

4. Неисправность control PWB

1. Еще раз внимательно прочитайте инструкцию по установке.

2. Убедитесь, что разъем подключен, а кабель не поврежден. При необходимости — замените.

3. Убедитесь, что разъем подключен, а кабель не поврежден.Заменить печатную плату.

4. Заменить плату управления PWB.

2. Неисправность в системе управления факсом PWB

1. Установить программное обеспечение для факса.

2. Заменить плату управления факсом PWB

C0840
Неисправность RTС
Расхождение во времени между RTC и текущим пять и более лет.
1. Неисправность control PWB

2. Отсоединена батарея.

1. Заменить плату управления PWB.

2. Визуально проверить и при необходимости исправить.

Переставить FAX control PWB

2. Неисправен привод основного двигателя.

3. Неисправен двигатель.

4. Неисправность control PWB

1. Вставьте разъем. Проверьте целостность кабеля.

3. Заменить.

4. Заменить.

C3100
Ошибка исходного положения ISU

1. Неисправность FFC между CCD PWB (YC1) и control PWB (YC8).

2. Неисправность FFC между control PWB (YC6) и сканера WPB (YC103) или неправильная установка FCC.

3. Неисправность датчика исходного положения.

4. Неисправность кабеля между двигателем ISU и сканером PWB (YC104) или разъем вставлен неправильно.

1. Заменить блок сканера ISU

2. Переставить FFC. Проверить на разрыв, при необходимости заменить.

3. Заменить датчик.

4. Вставьте разъем. Проверьте целостность кабеля.

2. Повреждения FFC между CCD PWB (YC1) и control PWB (YC8).

3. Неисправен кабель между CCD PWB (YC3) и LED приводом PWB (YC1) либо разъем не подключен.

4. Неисправен кабель между LED приводом PWB (YC2) и лампой экспонирования.

5. Лампа экспонирования вышла из строя.

6. Неисправен светодиодный привод.

1. Переустановите FFC. Проверьте целостность, при необходимости замените.

2. Заменить блок сканера.

3. Убедитесь, что разъем подключен, а кабель не поврежден. При необходимости — замените.

4. Убедитесь, что разъем подключен, а кабель не поврежден. При необходимости — замените.

5. Заменить лампу.

6. Заменить привод.

C3300
Ошибка AGC

1. Повреждения FFC между CCD PWB (YC1) и control PWB (YC8).

2. Лампа экспонирования вышла из строя.

3. Неисправность CCD PWB

4. Неисправность control PWB

1. Заменить блок сканера.

2. Заменить лампу.

3. Заменить CCD PWB

4. Заменить control PWB

C3500
Ошибка связи CPU — ASIC (CCD PWB)
Обнаружен код ошибки
1. Повреждения FFC между CCD PWB (YC1) и control PWB (YC8).

2. Неисправность CCD PWB.

3. Неисправность control PWB

1. Заменить блок сканера (ISU).

2. Заменить CCD PWB

3. Заменить control PWB

2. Неисправен блок лазерного сканера.

3. Неисправность control PWB

1. Убедитесь, что разъем подключен, а кабель не поврежден. При необходимости — замените.

2. Заменить блок сканера.

3. Заменить control PWB

C4200
Ошибка BD (блока лазерного сканера)

1. BD датчик не обнаруживает лазерный луч из-за скопления конденсата на зеркале.

2. Неисправен блок лазерного сканера.

2. Заменить блок сканера.

2. Плохой контакт в местах подключения нагревателя термоблока.

3. Термисторы фьюзера установлены неправильно.

4 . Срабатывает термореле

5. Нагреватель фьюзера установлен неправильно

6. Выход из строя термо-элемента

1. Проверьте контакты.

2. Проверьте контакты.

3. Заменить блок закрепления

4. Заменить блок закрепления

5. Заменить блок закрепления

6. Заменить блок закрепления

2. Неисправен шлейф термистора

3. Термистор установлен некорректно

4. Срабатывает термореле

Проверить контакты

Заменить блок закрепления

2. Дефект соединения между источником питания PWB (YC103) и PWB высокого напряжения (YC201)

3. Неисправен источник питания PWB

4. Неисправность control PWB

1. Переподключите коннектор.Убедитесь что кабель не поврежден.

2. Переподключите коннектор

3. Заменить источник питания

4. Заменить control PWB

2. Неисправен датчик отработки

3. Неисправность control PWB

1. Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла замените драм-юнит.

2. Замените датчик.

3. Заменить control PWB

4. Очистите драм юнит (инструкция по очистке бункера отработанного тонера)

F000
Ошибка связи control PWB — панель управления PWB

1. Неисправность соединения панели управления PWB (YC1) и control PWB (YC7).

2. Неисправность панели управления

3. Неисправность control PWB

1. Переподключите коннектор.Убедитесь что кабель не поврежден.

2. Замените панель.

3. Заменить control PWB

F020
Ошибка контрольной суммы RAM control PWB

1. Неисправность основной микросхемы памяти (ОЗУ) на главной плате управления PWB

2. Неисправность платы расширения памяти (DIMM)

1. Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла, замените control PWB

2. Замените плату расширения (DIMM)

F050
Ошибка контрольной суммы платы управления двигателем

1. Такие ошибки могут происходить при обновлении прошивки control PWB

2. Неисправность control PWB

1. Скачайте прошивку снова

2. Перезагрузите машину кратковременным выключением питания, если ошибка не исчезла, замените control PWB

F186
Ошибка управления видеоданными главной панели управления

Источник

Кто сейчас на форуме

Код C7990

Способ №2. Замена чипа

Другие неисправности

Способ №1. Сброс счетчика страниц / тонера

Сброс ошибок у принтеров Kyocera своими руками

Способы решения проблемы

Сброс сообщения о неоригинальном тонере на Kyocera fs 1040

Значения мигания индикаторов

Код C7990

Способ №2. Замена чипа

Другие неисправности

Способ №1. Сброс счетчика страниц / тонера

Сброс ошибок у принтеров Kyocera своими руками

Способы решения проблемы

Сброс сообщения о неоригинальном тонере на Kyocera fs 1040

Значения мигания индикаторов

Интересное по теме: