очень синий » Ср авг 03, 2011 11:01 am
Однажды был случай в далеком Макао — макака коалу в какао макала. Коала какао лениво лакала, макака макала, коала икала
-
очень синий
- Заправил картридж
-
Salek68 » Ср авг 03, 2011 11:06 am
Удача – это умение использовать каждый шанс.
-
Salek68
- Собрал картридж правильно
-
- ICQ
ard » Ср авг 03, 2011 11:06 am
Выписка из SM
код ошибки C0410 (A0410*)
- Код: выделить все
Optional DP communication problem
Communication fails five times successively.1.DP installed incorrectly.
---Check the installation state of the DP and
adjust it if it is not properly installed.
2.Defective main
PCB or DP driver PCB.
-----Replace the main PCB or DP driver PCB
and check for correct operation.
-
ard
- Собрал картридж
-
baton86 » Ср авг 03, 2011 3:27 pm
Optional DP communication problem — что это значит!!!
Копир печатает 1 страницу нормально, при печати 2 страницы показывает вот эту ошибку «сначала А-0 потом 410»
-
baton86
- Увидел тонер
-
- ICQ
baton86 » Ср сен 07, 2011 9:23 am
- Код: выделить все
Optional DP communication problem
Communication fails five times successively.1.DP installed incorrectly.
---Check the installation state of the DP and
adjust it if it is not properly installed.
2.Defective main
PCB or DP driver PCB.
-----Replace the main PCB or DP driver PCB
and check for correct operation.
Получаетсячто мне нужно менять плату управления процессором? Или можно обойтись более меньшими жертвами?!!!
И еще когда принесли его на ремонт, то он отработал 2 дня и не разу не выдал ошибку. Как тока забрали его обратно и установили на рабочем месте он начал опять выдавать эту ошибку. Из-за шлейфа который идет от сканера на главную плату, не может этого быть?
-
baton86
- Увидел тонер
-
- ICQ
baton86 » Ср сен 07, 2011 10:21 am
kvg писал(а):От сканера нет. Или вы имеете ввиду какой-то другой шлейф?
Провод который идет с верхней крышки в сам аппарат.
-
baton86
- Увидел тонер
-
- ICQ
Ruslan » Ср мар 14, 2012 2:51 pm
У меня KM-1620 выкидывает вот такое. Походе по интервалу на фотовал, я его менял и ракель тоже. Коротрон чистил, тонер GOLD ATM. У ког какие идеи?
-
Ruslan
- Не испугался и подошел к тонеру
-
- ICQ
Andreyak777 » Ср мар 14, 2012 2:56 pm
То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.
-
Andreyak777
- Избран тонером
-
Вернуться в Принтеры, МФУ, копиры формата A3
Кто сейчас на форуме
Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 10
Если при работе с копировальном аппаратом у вас возникли проблемы, и система выдает код ошибки, вы можете идентифицировать ее с помощью данной таблицы.
Коды ошибок Kyocera-Mita указаны для более поздних моделей копиров. Если вы являетесь владельцем более ранней модели, необходимо к трехзначному коду ошибки прибавить знак «0».
Если при работе с копировальном аппаратом у вас возникли проблемы, и система выдает код ошибки, вы можете идентифицировать ее с помощью данной таблицы.
Коды ошибок Kyocera-Mita указаны для более поздних моделей копиров. Если вы являетесь владельцем более ранней модели, необходимо к трехзначному коду ошибки прибавить знак «0».
Общие ошибки
| Код ошибки | Описание |
|---|---|
| 0030 | Fax control PWB system problem |
| 0070 | Fax control PWB incompatibility detection problem |
| 0100 | Backup memory read/write problem (main board) |
| 0110 | Backup memory data problem (main board) |
| 0120 | Drum EEPROM read/write problem (для 2550) |
| 0130 | Backup memory read/write problem (main PCB EEPROM) (для 1650/2050/2550) |
| 0140 | Backup memory data problem (main PCB EEPROM) (для 1650/2050/2550) |
| 0150 | Backup memory read/write problem (engine board) |
| 0160 | Backup memory data problem (engine board) |
| 0170 | Accounting count problem |
| 0180 | Machine number mismatch |
| 0210 | Communication problem between the main board and engine board (для KM-1500/1620/2020/1635/2035/1650/2050/2550/6030/8030, FS-1018/1118) |
| Communication problem between the main board and operation board (для KM-1525/1530/2030/2530/3530/6230/4530/5530/6330/7530) | |
| 0240 | Printer board PWB communication problem |
| 0250 | Scanner network board communication problem |
| 0280 | Communication problem between the fax control PWB and main PWB |
| 0320 | Side deck communication problem |
| 0340 | Finisher communication problem |
| 0410 | Optional DP communication problem |
| 0420 | Optional first paper feeder communication problem |
| Large paper deck /paper feed desk communication problem /Side deck communication problem | |
| 0440 | Finisher communication problem |
| 0450 | Mailbox communication problem |
| 0470 | Switchback unit communication problem |
| 0500 | Optional second paper feeder communication problem |
| 0510 | Optional third paper feeder communication problem |
| 0600 | DIMM problem (для 2530/3530) |
| 0610 | Bitmap (DIMM) problem |
| 0620 | Memory input interface problem |
| 0630 | DMA problem |
| 0640 | Hard disk drive problem |
| 0800 | Image processing problem (JAM05 is detected twice) |
| 0820 | Fax control PCB CG ROM checksum error |
| 0830 | Flash ROM program area checksum error |
| 0860 | Fax control PCB software switch checksum error |
| 0870 | Fax control PWB to main PWB high capacity data transfer problem |
| 0880 | Fax control PWB program archive problem |
| 0890 | Fax control PCB CG font archive problem |
| 0900 | Fax software incompatibility detection problem |
| 0920 | Fax file system error |
| 0960 | Developer EEPROM read/write problem (для 2550/6030/8030) |
| 1000 | Exposure lamp problem |
| 1010 | Lift motor 1 error |
| 1020 | Lift motor 2 error |
| 1030 | Lift motor 3 error |
| 1040 | Lift motor 4 error |
| 1100 | Paper deck motor 1 problem [Drawer 3] |
| 1110 | Paper deck motor 2 problem [Drawer 4] |
| 1120 | Deck right lift position problem |
| 1130 | Deck left lift position problem |
| 1140 | Side deck lift motor (going up) problem |
| 1150 | Side deck lift motor (going down) problem |
| 1160 | Large paper deck (paper feed desk) sequence problem |
| 1170 | Large paper deck (paper feed desk) incorrect type problem |
| 2000 | Main motor problem |
| Image forming motor problem (для 6230/4530/5530/6330/7530) | |
| 2500 | Paper feed motor problem |
| 2550 | Paper conveying motor problem (для 4530/5530) |
| 2600 | Deck conveying motor /desk drive motor problem |
| 2640 | Side deck drive motor problem |
| 3100 | Scanner carriage problem |
| 3200 | Exposure lamp problem |
| 3300 | Optical system (AGC) problem |
| 4000 | Polygon motor synchronization problem |
| 4010 | Polygon motor steady-state problem |
| 4100 | BD initialization (A) problem |
| 4110 | BD initialization (B) problem |
| 4200 | BD steady-state problem |
| 5100 | Main charger problem |
| 5110 | Transfer/separation high voltage problem |
| 5300 | Broken cleaning lamp wire |
| 5500 | Drum surface potential sensor problem 1 |
| 5510 | Drum surface potential sensor problem 2 |
| 5600 | Drum surface potential problem 1 |
| 5610 | Drum surface potential problem 2 |
| 6000 | Broken fixing heater wire |
| 6020 | Abnormally high fixing unit thermistor temperature |
| 6030 | Broken fixing unit thermistor |
| 6050 | Abnormally low fixing unit thermistor temperature |
| 6100 | Broken fixing heater wire |
| 6200 | Abnormally low fixing unit thermistor temperature |
| 6300 | Abnormally high fixing unit thermistor temperature |
| 6400 | Zero-crossing signal problem |
| 6410 | Fixing unit connector insertion problem |
| 6420 | Fixing fuse cut problem |
| 6420 | Broken fixing unit thermistor wire |
| 7100 | Toner sensor problem |
| 7300 | Broken external temperature thermistor wire (для KM-1505/1510/1810/4230/5230/6230) |
| Toner sensor problem/ Toner hopper problem (для KM-2530/3530/3035/4035/5035/6230/4530/5530/6330/7530/6030/8030) | |
| 7310 | Short-circuited external temperature thermistor |
| 7400 | Image formation unit connector insertion problem |
| Developing unit connector insertion problem (для 2550) | |
| 7410 | Drum unit connector insertion problem |
| 7750 | Drum type mismatch problem A (для 1635/2035) |
| 7760 | Drum type mismatch problem B (для 1635/2035) |
| 7800 | Broken external temperature thermistor |
| 7810 | Short-circuited external temperature thermistor |
KM-1500, FS-1018/1118 (KM-1820)
| Код ошибки | Описание |
|---|---|
| 0220 | Communication problem between the main board and operation board (для 1018/1118) |
| F— | Controller system error (для 1018/1118) |
| F010 | ROM checksum error (для 1118) |
| F012 | |
| 7980 | Waste toner reservoir overflow problem (when the total number of copies is less than 100 thousand sheets) |
| 7990 | Waste toner reservoir overflow problem (when the total number of copies is 100 thousand sheets or more) |
KM-1505/1510/1810/1525/1530/2030
| Код ошибки | Описание |
|---|---|
| 0210 | Printer board communication problem (для 1505/1510/1810) |
| 0400 | DIMM problem |
| 0410 | Bitmap problem |
| 0430 | DMA problem |
| 1040 | Optical system problem (AGC) |
Kyocera-Mita 3035/4035/5035
| Код ошибки | Описание |
|---|---|
| 0100 | Operation unit PCB backup memory read/write error |
| 0110 | Operation unit PCB backup memory data problem |
| 0210 | MMI communication problem |
| 0320 | Energy save communication problem |
| 7450 | Image formation unit fuse cut problem |
Kyocera Mita 4230/5230
| Код ошибки | Описание |
|---|---|
| 0010 | Memory copy PCB 1 communication problem |
| 0030 | Memory copy PCB 2 communication problem |
| 0100 | RAM/ROM problem |
| 0220 | Communication problem between the engine PCB and main PCB |
| 0230 | Scanner communication problem |
| 0260 | Memory copy PCB 1 communication problem |
| 0320 | Large paper deck communication problem /Paper feed desk communication problem |
| 0360 | Memory copy PCB 2 communication problem |
| 0370 | Communication microcomputer problem |
| 1040 | Optical system problem (AGC) |
| 2100 | Paper conveying motor problem |
| 2200 | Side registration motor problem |
| 2300 | Paper feed motor problem |
| 2310 | Desk drive motor problem |
| 2410 | Upper lift motor problem |
| 2420 | Lower lift motor problem |
| 2430 | Upper desk lift motor problem |
| 2440 | Lower desk lift motor problem |
| 3320 | Scanner watchdog problem |
| 3400 | Original detection position problem |
| 7400 | Toner hopper problem |
| 9200 | Deck paper conveying motor problem |
| 9210 | Paper deck motor 1 problem |
| 9220 | Paper deck motor 2 problem |
| 9230 | Right lift position problem |
| 9240 | Left lift position problem |
Kyocera-Mita 6030/8030
| Код ошибки | Описание |
|---|---|
| 0060 | Main PWB type mismatch error |
| 0130 | Backup memory (EEPROM) device problem |
| 0140 | Backup memory (EEPROM) data problem |
| 0220 | Scanner communication problem |
| 0330 | Relay board communication problem |
| 0460 | Duplex unit communication problem |
| 0470 | Sheet inserter communication problem (optional document finisher) |
| 0500 | Paper feed unit communication error (cassette 1 and 2) |
| 0510 | Paper feed unit communication error (cassette 3 and 4) |
| 0700 | Side feeder EEPROM error (optional side feeder) |
| 0750 | Document finisher EEPROM error |
| 0970 | Cleaning unit EEPROM error |
| 1200 | Duplex side registration motor error |
| 2100 | Developing motor error |
| 2200 | Drive motor error |
| 2300 | Fuser motor error |
| 2550 | Transfer motor error |
| 3210 | CIS lamp problem |
| 3310 | Optical system (AGC) problem (DP) |
| 3500 | Communication error between scanner and SHD |
| 3900 | Backup memory read/write error (scanner PWB) |
| 3910 | |
| 4120 | BD initialization (C) problem |
| 7200 | Broken drum thermistor wire |
| 7210 | Shorted drum thermistor |
| 9040 | DP lift motor going up error |
| 9050 | DP lift motor going down error |
| 9060 | DP EEPROM error |
| 9070 | Communication problem between DP and SHD |
| 9080 | Communication problem between DP and CIS |
Kyocera Mita 6230
| Код ошибки | Описание |
|---|---|
| 0010 | Memory PCB communication problem |
| 0100 | RAM/ROM problem |
| 0260 | Memory copy PCB 1 communication problem |
| 0350 | Mailbox communication problem |
| 0370 | Communication microcomputer problem |
| 0380 | Hard disk problem |
| 0390 | DIMM problem |
| 1040 | Optical system problem (AGC) |
| 2100 | Drive motor problem / Paper conveying motor problem |
| 2200 | Paper feed motor problem |
| 2300 | Large paper deck right lift motor problem |
| 2310 | Large paper deck left lift motor problem |
| 2420 | Upper lift motor problem |
| 2430 | Lower lift motor problem |
| 6500 | Broken fixing unit thermistor wire |
| 7200 | Broken drum thermistor wire |
| 7210 | Shorted drum thermistor |
| 7220 | Broken drum heater wire |
KyoceraMita 6330/7530
| Код ошибки | Описание |
|---|---|
| 1060 | Large paper deck left lift motor problem |
| 2550 | Drive motor problem |
| 7520 | Shorted drum thermistor |
| 7530 | Broken drum thermistor wire |
Ошибки финишеров
| Код ошибки | Описание |
|---|---|
| 8010 | Finisher paper conveying motor problem |
| 8030 | Finisher (upper) paper conveying belt problem |
| 8140 | Finisher tray elevation motor problem /Main tray problem |
| 8170 | Finisher front side registration motor problem |
| 8180 | Finisher rear side registration motor problem |
| Finisher rear jogger motor problem (для 4230/5230) | |
| 8190 | Finisher trailing edge registration motor problem |
| 8210 | Finisher stapler motor problem |
| 8220 | Finisher rear stapler problem |
| 8300 | Document finisher centerfold unit communication problem |
| 8310 | Document finisher centerfold unit side registration guide problem |
| 8320 | Document finisher centerfold unit centering plate problem |
| 8330 | Document finisher centerfold blade problem |
Ошибки финишеров KM-2530/3530/3035/4035/5035
| Код ошибки | Описание |
|---|---|
| 8300 | Booklet stitcher paper ejection motor problem |
| 8310 | Booklet stitcher elevation motor problem |
| 8320 | Booklet stitcher rear jog motor problem |
| 8330 | Booklet stitcher front jog motor problem |
| 8340 | Booklet stitcher staple motor problem |
| 8350 | Booklet stitcher batch processing motor problem |
| 8360 | Booklet stitcher stapler shift motor problem |
| 8370 | Booklet stitcher paddle motor problem |
| 8380 | Booklet stitcher folding problem |
| 8390 | Booklet stitcher backup RAM data problem |
| 8400 | Booklet stitcher incorrect type problem |
| 8410 | Booklet stitcher punch motor problem |
| 8420 | Booklet stitcher shift motor problem |
| 8430 | Booklet stitcher punch communication problem |
| 8440 | Booklet stitcher punch sensor problem |
| 8450 | Booklet stitcher side punch sensor problem |
| 8460 | Booklet stitcher punch backup RAM data problem |
| 8470 | Booklet stitcher punch dust sensor problem |
| 8480 | Booklet stitcher broken punch power source wire problem |
| 8500 | Mailbox drive motor problem |
Ошибки финишера KM-6230
| Код ошибки | Описание |
|---|---|
| 8180 | Finisher rear jogger motor problem |
| 8310 | Booklet stitcher paper ejection motor problem |
| 8320 | Booklet stitcher elevation motor problem |
| 8330 | Booklet stitcher jog motor problem |
| 8340 | Booklet stitcher staple motor problem |
| 8350 | Booklet stitcher stapler unit shift motor problem |
| 8360 | Booklet stitcher stack level detection sensor problem |
| 8370 | Booklet stitcher punch motor problem |
| 8380 | Booklet stitcher punch shift motor problem |
| 8390 | Booklet stitcher swing motor problem |
| 8400 | Booklet stitcher backup RAM data problem |
| 8410 | Booklet stitcher punch unit backup RAM data problem |
| 8420 | Booklet stitcher positioning plate motor problem |
| 8430 | Booklet stitcher folding motor problem |
| 8440 | Booklet stitcher guide motor problem |
| 8450 | Booklet stitcher jog motor problem |
| 8460 | Booklet stitcher rear staple motor problem |
| 8470 | Booklet stitcher front staple motor problem |
| 8480 | Booklet stitcher thrust motor problem |
| 8490 | Booklet stitcher communication error |
Ошибки финишеров KM-6330/7530/6030/8030
| Код ошибки | Описание |
|---|---|
| 8000 | Document finisher incorrect type problem (для 6330/7530) |
| 8020 | Finisher punch motor problem |
| 8040 | Finisher lower paper conveying belt problem |
| 8150 | Finisher multi job tray problem |
| 8170 | Front upper side-registration guide problem |
| 8180 | Finisher rear upper side-registration guide problem |
| 8190 | Finisher lower side-registration guide problem |
| 8220 | Finisher front clincher problem |
| 8230 | Finisher rear stapler problem |
| 8240 | Finisher rear clincher problem |
Оборудование оснащено функцией самодиагностики. При обнаружении проблемы, аппарат блокируется, на дисплее отображается код вида С#### с указанием характера проблемы. Также появляется сообщение необходимости обслуживания. После устранения проблемы, ошибку можно сбросить тумблером питания, выключив и включив аппарат.
При обнаружении неисправности дополнительного устройства (ошибки C8170, C8180, C8190, C8210)* производится частичная блокировка функциональности аппарата. После устранения неисправности ошибку можно сбросить в сервисном режиме U906.
Ошибки узла закрепления изображения (печные ошибки) C6###, после устранения неисправности и в целях безопасности, сбрасываются только в сервисном режиме U163.
Таблица кодов ошибок:
| Код |
Значение |
Описание |
Причина |
Решение |
| C0100 |
Backup memory (EEPROM) device problem (main) |
Reading from or writing to EEPROM cannot be performed. | Defective main/engine PWB. |
Replace the main/engine PWB and check for correct operation. |
| C0110 |
Backup memory data problem (main) |
Data in the specified area of the backup memory does not match the specified values. | Data damage of EEPROM. |
Contact the Service Administrative Division. |
| C0150 |
Backup memory device problem (engine EEPROM) |
Reading from or writing to EEPROM cannot be performed. | Defective main/engine PWB. |
Replace the main/engine PWB and check for correct operation. |
| Device damage of EEPROM. |
Contact the Service Administrative Division. | |||
| C0160 |
Backup memory data problem (engine EEPROM) |
Reading data from EEPROM is abnormal. | Data damage of EEPROM. |
Contact the Service Administrative Division. |
| C0170 |
Copy counts problem |
When the power is turned on, the total count and the scan count are abnormal both on the main and engine. | Data damage of EEPROM. |
Contact the Service Administrative Division. |
| Defective main/engine PWB. |
Replace the main/engine PWB and check for correct operation. | |||
| C0180 |
Machine number mismatch |
Machine number of main and engine does not match. | Data damage of EEPROM. |
Contact the Service Administrative Division. |
| C0210 |
Communication problem between the main and engine |
When the power is turned on, the machine does not detect the low level of SBSY and the high level of SDIR for 10 s. | Poor contact in the connector terminals. |
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. |
| Defective main/engine PWB. |
Replace the main/engine PWB and check for correct operation. | |||
| C0240 |
Printer PWB communication problem |
The printer PWB does not respond 120 s after the power is turned on. | Poor contact in the connector terminals. |
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. |
| Defective main/engine PWB. |
Replace the main/engine PWB and check for correct operation. | |||
| A0410 |
Document processor communication problem |
Communication fails five times successively. | Document processor installed incorrectly. |
Check the installation state of the document processor and adjust it if it is not properly installed. |
| Defective PWB. |
Replace the main/engine PWB or DP driver PWB and check for correct operation. | |||
| A0420 |
First paper feeder communication problem |
Communication fails five times successively. | First paper feeder installed incorrectly. |
Check the installation state of the first paper feeder and adjust it if it is not properly installed. |
| Defective PWB. |
Replace the main/engine PWB or cassette main PWB and check for correct operation. | |||
| C0440* |
Built-in finisher communication problem |
Communication fails five times successively. | Poor contact in the connector terminals. |
Check the connection of connector YC4 on the engine PWB and the connector of the built-in finisher, and the continuity across the connector terminals. Repair or replace if necessary. |
| Defective PWB. |
Replace the engine PWB or finisher main PWB and check for correct operation. | |||
| A0500 |
Second paper feeder communication problem |
Communication fails five times successively. | Second paper feeder installed incorrectly. |
Check the installation state of the second paper feeder and adjust it if it is not properly installed. |
| Defective PWB. |
Replace the main/engine PWB or cassette main PWB and check for correct operation. | |||
| A0510 |
Third paper feeder communication problem |
Communication fails five times successively. | Third paper feeder installed incorrectly. |
Check the installation state of the third paper feeder and adjust it if it is not properly installed. |
| Defective PWB. |
Replace the main/engine PWB or cassette main PWB and check for correct operation. | |||
| C0610 |
Bitmap (DIMM) problem |
There is a problem with the data or address bus of the bitmap DRAM. | Defective main/engine PWB. |
Replace the main/engine PWB and check for correct operation. |
| DIMM installed incorrectly. |
Check if the DIMM is inserted into the socket on the main/engine PWB correctly. | |||
| Defective DIMM. |
Replace the DIMM and check for correct operation. | |||
| C0620 |
Memory input interface problem |
Reading-in of an image does not complete within 10 s of the start of image transmission. | Defective main/engine PWB. |
Replace the main/engine PWB and check for correct operation. |
| C0630 |
DMA problem |
DMA transmission of compressed, decompressed, rotated, relocated or blanked-out image data does not complete within the specified period of time. | Defective main/engine PWB. |
Replace the main/engine PWB and check for correct operation. |
| C0800 |
Image processing problem |
JAM05 is detected twice. | Defective main/engine PWB. |
Replace the main/engine PWB and check for correct operation. |
| C2000 |
Drive motor problem |
A stable state does not continue for 1 s from 1 s after the drive motor is activated. | Poor contact in the connector terminals. |
Check the connection of connector YC6 on the main/engine PWB and the connector on the drive motor, and the continuity across the connector terminals. Repair or replace if necessary. |
| Defective drive transmission system. |
Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. | |||
| Defective main/engine PWB. |
Replace the main/engine PWB and check for correct operation. | |||
| Defective drive motor. |
Replace the drive motor. | |||
| C2200 |
Drum motor problem |
A stable state does not continue for 1 s from 1 s after the drum motor is activated. | Poor contact in the connector terminals. |
Check the connection of connector YC6 on the main/engine PWB and the connector on the drum motor, and the continuity across the connector terminals. Repair or replace if necessary. |
| Defective drive transmission system. |
Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. | |||
| Defective main/engine PWB. |
Replace the main/engine PWB and check for correct operation. | |||
| Defective drum motor. |
Replace the drum motor. | |||
| C3100 |
Scanner carriage problem |
The home position is not correct when the power is turned on or at the start of copying using the table. | Poor contact in the connector terminals. |
Check the connection of connector YC5 on the main/engine PWB and the connector on the home position switch, and the continuity across the connector terminals. Repair or replace if necessary. |
| Defective home position switch. |
Replace the home position switch. | |||
| Defective scanner motor. |
Replace the scanner motor. | |||
| The mirror frame, exposure lamp, or scanner wire is defective. |
Check if the mirror flames and exposure lamp are on the rail. And check the scanner wire winds correctly. | |||
| Defective main/engine PWB. |
Replace the main/engine PWB and check for correct operation. | |||
| C3200 |
Exposure lamp problem |
Non-lighting of the exposure lamp is detected at the beginning of copying. | Poor contact in the connector terminals. |
Check the connection of connector YC16 on the main/engine PWB and the connector on the inverter PWB, and the continuity across the connector terminals. Repair or replace if necessary. |
| Defective exposure lamp. |
Replace the exposure lamp. | |||
| Incorrect shading position. |
Adjust the position of the contact glass (shading plate). If the problem still occurs, replace the home position switch. | |||
| Defective PWB. |
Replace the main/engine PWB or inverter PWB and check for correct operation. | |||
| C3300 |
AGC problem |
After AGC, correct input is not obtained at CCD. | Poor contact in the connector terminals. |
Check the connection of connector YC27 on the main/engine PWB and the connector on the CCD PWB, and the continuity across the connector terminals. Repair or replace if necessary. |
| Defective exposure lamp. |
Replace the exposure lamp. | |||
| Defective PWB. |
Replace the main/engine PWB or CCD PWB and check for correct operation. | |||
| C4000 |
Polygon motor synchronization problem |
The polygon motor does not reach the stable speed within 20 s of the START signal turning on. | Poor contact in the connector terminals. |
Check the connection of connector YC3 on the main/engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary. |
| Defective polygon motor. |
Replace the laser scanner unit. | |||
| Defective main/engine PWB. |
Replace the main/engine PWB and check for correct operation. | |||
| C4010 |
Polygon motor steady-state problem |
Stable OFF is detected for 5 s continuously after polygon motor stability. | Poor contact in the connector terminals. |
Check the connection of connector YC3 on the main/engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary. |
| Defective polygon motor. |
Replace the laser scanner unit. | |||
| Defective main/engine PWB. |
Replace the main/engine PWB and check for correct operation. | |||
| C4200 |
BD steady-state problem |
ASIC detects a BD error for 600 ms after the polygon motor rotation has been stabilized. | Poor contact in the connector terminals. |
Check the connection of connector YC3 on the main/engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary. |
| Defective laser scanner unit. |
Replace the laser scanner unit. | |||
| Defective main/engine PWB. |
Replace the main/engine PWB and check for correct operation. | |||
| C6000 |
Fuser heater break |
The temperature does not reach 70 °C/ 158°F in 15 s before secondary stabilization. Temperature rise of 1°C/1.8°F does not occur in 5 s before secondary stabilization (except during printing). | Poor contact in the fuser thermistor connector terminals. |
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. |
| Fuser thermistor installed incorrectly. |
Check and reinstall if necessary. | |||
| Fuser thermostat triggered. |
Check for continuity. If none, replace the fuser thermostat. | |||
| Fuser heater installed incorrectly. |
Check and reinstall if necessary. | |||
| Broken fuser heater wire. |
Check for continuity. If none, replace the fuser heater. | |||
| C6020 |
Abnormally high fuser thermistor temperature |
Fuser thermistor is detected 230°C/ 446°F or more for 40 ms. | Shorted thermistor. |
Measure the resistance. If it is 0 Ω, replace the thermistor. |
| Broken heater control circuit on the power source PWB. |
Replace the power source PWB and check for correct operation. | |||
| C6050 |
Abnormally low fuser thermistor temperature |
Fuser thermistor remains below 90°C/ 194°F for 1 s. | Poor contact in the fuser thermistor connector terminals. |
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. |
| Broken fuser thermistor wire. |
Measure the resistance. If it is ∞ Ω, replace the fixing thermistor. | |||
| Fuser thermistor installed incorrectly. |
Check and reinstall if necessary. | |||
| Fuser thermostat triggered. |
Check for continuity. If none, replace the fuser thermostat. | |||
| Fuser heater installed incorrectly. |
Check and reinstall if necessary. | |||
| Broken fuser heater wire. |
Check for continuity. If none, replace the fuser heater. | |||
| C6400 |
Zero-cross signal error |
Interrupt of the zero-cross signal does not occur more than 1 s. | Poor contact in the connector terminals. |
Reinsert the connector. Also check for conti- nuity within the connector cable. If none, remedy or replace the cable. |
| Defective power source PWB. |
Check if the zero-crossing signal is output from YC2-2 on the power source PWB. If not, replace the power source PWB. | |||
| Defective main/engine PWB. |
Replace the main/engine PWB if C6400 is detected while YC2-2 on the power source PWB outputs the zero-crossing signal. | |||
| C7800 |
Broken external thermistor wire |
The thermistor output value is 0.5 V or less. | Poor contact in the connector terminals. |
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. |
| Defective humidity sensor. |
Replace the cassette PWB and check for correct operation. | |||
| C7810 |
Short-circuited external thermistor wire |
The thermistor output value is 4.5 V or more. | Poor contact in the connector terminals. |
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. |
| Defective humidity sensor. |
Replace the cassette PWB and check for correct operation. | |||
| C8170* |
Built-in finisher front side registration motor problem |
When the front-side registration home- position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses. When the front-side registration home- position sensor is turned off during initialization, the sensor did not turn on in 3 s. | The front side registration motor connector makes poor contact. |
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. |
| Defective front side registration motor. |
Replace front side registration motor. | |||
| The front side registration home position sensor connector makes poor contact. |
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. | |||
| Defective front side registration home position sensor. |
Replace the front side registration home position sensor. | |||
| Defective finisher control PWB. |
Replace the finisher control PWB and check for correct operation. | |||
| C8180* |
Built-in finisher rear side registration motor problem |
When the rear-side registration home- position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses. When the rear-side registration home- position sensor is turned off during initialization, the sensor did not turn on in 3 s. | The rear side registration motor connector makes poor contact. |
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. |
| Defective rear side registration motor. |
Replace rear side registration motor. | |||
| The rear side registration home position sensor connector makes poor contact. |
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. | |||
| Defective rear side registration home position sensor. |
Replace the rear side registration home position sensor. | |||
| Defective finisher control PWB. |
Replace the finisher control PWB and check for correct operation. | |||
| C8190* |
Built-in finisher trailing edge registration motor problem |
When the trailing edge registration home-position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses. When the trailing edge registration home-position sensor is turned off during initialization, the sensor did not turn on in 3 s. | The trailing edge registration motor connector makes poor contact. |
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. |
| Defective trailing edge registration motor. |
Replace trailing edge registration motor. | |||
| The trailing edge registration home position sensor connector makes poor contact. |
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. | |||
| Defective trailing edge registration home position sensor. |
Replace the trailing edge registration home position sensor. | |||
| Defective finisher control PWB. |
Replace the finisher control PWB and check for correct operation. | |||
| C8210* |
Built-in finisher stapler problem |
The stapler home position sensor does not change state from nondetection to detection within 200 ms of the start of stapler motor counterclockwise (forward) rotation. During initialization, the stapler home position sensor does not change state from non-detection to detection within 600 ms of the start of stapler motor clockwise (reverse) rotation. | The stapler connector makes poor contact. |
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. |
| The stapler is blocked with a staple. |
Remove the stapler cartridge, and check the cartridge and the stapling section of the stapler. | |||
| The stapler is broken. |
Replace the front stapler and check for correct operation. | |||
| Defective finisher control PWB. |
Replace the finisher control PWB and check for correct operation. |
*) Kyocera TASKalfa 181/221
Если при работе с копировальном аппаратом у вас возникли проблемы, и система выдает код ошибки, вы можете идентифицировать ее с помощью данной таблицы.
Коды ошибок Kyocera-Mita указаны для более поздних моделей копиров. Если вы являетесь владельцем более ранней модели, необходимо к трехзначному коду ошибки прибавить знак «0».