Куосера таскальфа 180 ошибка е

Прилепить пост

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑Вощем начало банальное.
Пришло сие гуано, с диагнозом «Не работает» (как обычно сос слов клиента).
Включаю, ага вот оно: «Е» и «Встряхните картр. с тонером».
С такой хней встретился в первый раз… Погуглил… Нету… Второй раз погуглил.. На СК гонево про левый тонер и бла-бла-бла…
Похер начнем сами.
Открыл крышку драма… Опа… А бункер отработки где… Позвонил… к вечеру привезли…
18:00, пора домой…
Пришел утром… Поставил бункер..
Та же ошибка…
Снимает бункер тонера, тонер высыпаем, смотрим как работают мешалки, как шнек подачи подает тонер…
Высыпается из положенного отверстия.
Ога… Все обратно, снимаем узел ФБ…
Ой пля… А чей то он не крутится, все разбираем, смотрим, чистим… Ога поехало, обратно все собрать — поставить…
Плеат.. та же ошибка..
Снимем заднюю крышку, проверить как двигателя работают… Ога, черная хня которая закрывает полусектор привода шнека, не вращается, муфта проворачивается… Вот то место на фото..

Снимаю полностью привод (как все делал, не снял к сожалению, фото того что именнно надо смотреть ниже),

чищу, муфту полностью разбираю, промываю изопропанолом от смазки родной, чуть смазываю фьюзеркой риковской (я ее все мажу :-) :-) :-) ), собираю, возвращаю все на место…
Уряяя, ошибка пропала…
При старте пишет что тонер неизвеснтый но выходит в готовность… Делаем копию… Плеан что это лист напротив ФБ встает в гармошку…
Ивоюж мать… Снимаю опять привод, и смотрю уже трехлепистковый привод уже ФБ…
Уже матов нету, он на валу провернулся…
Засверливаю вал… вставляю поперек вала в отверстие кусок проволоки, в самом приводе (пластмассовом делаю канавки, и все собираю на место… Уффф.
Все поехало… 50 листов… полет нормальный… 250 листов… Полет нормальный…
Делаю распечатку системы и копию… Чуть более 98 тыс. копий…
Да… так уговнякать аппарат миллионник надо уметь…
Ну что сказать люди с высшим юридическим не умеют думать… Мое мнение…
Короче как то таг… Сумбурно… Но может кому то поможет…
С уважением Николай ака manik.76.

Аватар пользователя

manik.76

  

Over 9000 заправок

  • Не в сети
  • Сайт
  • ICQ
  • Персональный альбом
  • «ошибка принтера HSYNC»

    Sunat в форуме Xerox 3100 и иже с ним…

    10
    29498

    Sunat
    Перейти к последнему сообщению
    Сб май 10, 2014 6:19 am
  • Samsung SCX 4300 V 1.15. Ошибка «Нет картриджа»

    PrintFree в форуме Картриджи, их заправка и дефекты.

    9
    10521

    С.Н.Н.
    Перейти к последнему сообщению
    Пт авг 19, 2011 7:16 pm
  • Canon mf635cx ошибка «замятие»

    belocarsk в форуме Принтеры, МФУ, факсы, копиры формата A4

    8
    5380

    belocarsk
    Перейти к последнему сообщению
    Пн мар 04, 2019 12:23 pm
  • BROTHER DCP-1512R ошибка «Фотобарабан !»

    VIRT в форуме Принтеры, МФУ, факсы, копиры формата A4

    1
    4031

    kvg
    Перейти к последнему сообщению
    Чт сен 05, 2019 1:35 pm
  • brother DCP 7030R «ошибка барабана»

    vg2804 в форуме Принтеры, МФУ, факсы, копиры формата A4

    14
    20093

    Rexvil
    Перейти к последнему сообщению
    Пт окт 09, 2020 8:01 am

Вернуться в Принтеры, МФУ, копиры формата A3

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 10

Источник

Аналогичные аппараты: Kyocera TASKalfa 180 / TASKalfa 220

Коды ошибок:
C0100 — Backup memory (EEPROM) device problem (main) (не может быть выполнено чтение или запись в EEPROM)
C0110 — Backup memory data problem (main) (проблема резервного копирования данных в память)
C0150 — Backup memory device problem (engine EEPROM) (проблема в двигателе EEPROM)
C0160 — Backup memory data problem (engine EEPROM) (проблема в двигателе EEPROM)
C0170 — Copy counts problem (проблема счетчика копий
C0180 — Machine number mismatch (не совпадает номер аппарата и главного двигателя)
C0210 — Communication problem between the main and engine (проблема связи между платой и двигателем)
C0240 — Printer PWB communication problem (проблема с питанием)
A0410 — Document processor communication problem (сбой связи процессора)
A0420 — First paper feeder communication problem (проблема с первым податчиком бумаги)
A0500 — Second paper feeder communication problem (проблема со вторым податчиком бумаги)
A0510 — Third paper feeder communication problem (проблема с третьем податчиком бумаги)
C0610 — Bitmap (DIMM) problem (проблемы с данными или адресной шиной растрового изображения DRAM)
C0620 — Memory input interface problem (проблема памяти интерфейса ввода)
C0630 — DMA problem (проблема DMA)
C0800 — Image processing problem (проблема обработки изображения)
C2000 — Drive motor problem (проблема двигателя привода)
C2200 — Drum motor problem (проблема двигателя драма)
C3100 — Scanner carriage problem (проблема каретки сканера)
C3200 — Exposure lamp problem (проблема лампы экспонирования)
C3300 — AGC problem (проблема AGC)
C4000 — Polygon motor synchronization problem (проблема синхронизации двигателя полигона)
C4010 — Polygon motor steady-state problem (проблема двигателя полигона)
C4200 — BD steady-state problem (проблема BD)
C6000 — Fuser heater break (неисправность нагревателя печки)
C6020 — Abnormally high fuser thermistor temperature (аномально высокая температура термистора в печке)
C6050 — Abnormally low fuser thermistor temperature (аномально низкая температура термистора в печке)
C6400 — Zero-cross signal error (ошибка нулевого сигнала)
C7800 — Broken external thermistor wire (поломка внешних проводов термистора)
C7810 — Short-circuited external thermistor wire (короткое замыкание термистора)

Источник

Оборудование оснащено функцией самодиагностики. При обнаружении проблемы, аппарат блокируется, на дисплее отображается код вида С#### с указанием характера проблемы. Также появляется сообщение необходимости обслуживания. После устранения проблемы, ошибку можно сбросить тумблером питания, выключив и включив аппарат.

При обнаружении неисправности дополнительного устройства (ошибки C8170, C8180, C8190, C8210)* производится частичная блокировка функциональности аппарата. После устранения неисправности ошибку можно сбросить в сервисном режиме U906.

Ошибки узла закрепления изображения (печные ошибки) C6###, после устранения неисправности и в целях безопасности, сбрасываются только в сервисном режиме U163.

Таблица кодов ошибок:

Код
 Значение
 Описание
 Причина
 Решение





C0100
 Backup memory (EEPROM) device problem (main)
Reading from or writing to EEPROM cannot be performed. Defective main/engine PWB.
 Replace the main/engine PWB and check for correct operation.
C0110
 Backup memory data problem (main)
 Data in the specified area of the backup memory does not match the specified values. Data damage of EEPROM.
 Contact the Service Administrative Division.
C0150
 Backup memory device problem (engine EEPROM)
 Reading from or writing to EEPROM cannot be performed. Defective main/engine PWB.
 Replace the main/engine PWB and check for correct operation.


Device damage of EEPROM.
 Contact the Service Administrative Division.
C0160
 Backup memory data problem (engine EEPROM)
 Reading data from EEPROM is abnormal. Data damage of EEPROM.
 Contact the Service Administrative Division.
C0170
 Copy counts problem
 When the power is turned on, the total count and the scan count are abnormal both on the main and engine. Data damage of EEPROM.
 Contact the Service Administrative Division.


Defective main/engine PWB.
 Replace the main/engine PWB and check for correct operation.
C0180
 Machine number mismatch
 Machine number of main and engine does not match. Data damage of EEPROM.
 Contact the Service Administrative Division.
C0210
 Communication problem between the main and engine
 When the power is turned on, the machine does not detect the low level of SBSY and the high level of SDIR for 10 s. Poor contact in the connector terminals.
 Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.


Defective main/engine PWB.
 Replace the main/engine PWB and check for correct operation.
C0240
 Printer PWB communication problem
 The printer PWB does not respond 120 s after the power is turned on. Poor contact in the connector terminals.
 Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.


Defective main/engine PWB.
 Replace the main/engine PWB and check for correct operation.
A0410
 Document processor communication problem
 Communication fails five times successively. Document processor installed incorrectly.
 Check the installation state of the document processor and adjust it if it is not properly installed.


Defective PWB.
 Replace the main/engine PWB or DP driver PWB and check for correct operation.
A0420
 First paper feeder communication problem
 Communication fails five times successively. First paper feeder installed incorrectly.
 Check the installation state of the first paper feeder and adjust it if it is not properly installed.


Defective PWB.
 Replace the main/engine PWB or cassette main PWB and check for correct operation.
C0440*
 Built-in finisher communication problem
 Communication fails five times successively. Poor contact in the connector terminals.
 Check the connection of connector YC4 on the engine PWB and the connector of the built-in finisher, and the continuity across the connector terminals. Repair or replace if necessary.


Defective PWB.
 Replace the engine PWB or finisher main PWB and check for correct operation.
A0500
 Second paper feeder communication problem
 Communication fails five times successively. Second paper feeder installed incorrectly.
 Check the installation state of the second paper feeder and adjust it if it is not properly installed.


Defective PWB.
 Replace the main/engine PWB or cassette main PWB and check for correct operation.
A0510
 Third paper feeder communication problem
 Communication fails five times successively. Third paper feeder installed incorrectly.
 Check the installation state of the third paper feeder and adjust it if it is not properly installed.


Defective PWB.
 Replace the main/engine PWB or cassette main PWB and check for correct operation.
C0610
 Bitmap (DIMM) problem
 There is a problem with the data or address bus of the bitmap DRAM. Defective main/engine PWB.
 Replace the main/engine PWB and check for correct operation.


DIMM installed incorrectly.
 Check if the DIMM is inserted into the socket on the main/engine PWB correctly.

Defective DIMM.
 Replace the DIMM and check for correct operation.
C0620
 Memory input interface problem
 Reading-in of an image does not complete within 10 s of the start of image transmission. Defective main/engine PWB.
 Replace the main/engine PWB and check for correct operation.
C0630
 DMA problem
 DMA transmission of compressed, decompressed, rotated, relocated or blanked-out image data does not complete within the specified period of time. Defective main/engine PWB.
 Replace the main/engine PWB and check for correct operation.
C0800
 Image processing problem
 JAM05 is detected twice. Defective main/engine PWB.
 Replace the main/engine PWB and check for correct operation.
C2000
 Drive motor problem
 A stable state does not continue for 1 s from 1 s after the drive motor is activated. Poor contact in the connector terminals.
 Check the connection of connector YC6 on the main/engine PWB and the connector on the drive motor, and the continuity across the connector terminals. Repair or replace if necessary.


Defective drive transmission system.
 Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.

Defective main/engine PWB.
 Replace the main/engine PWB and check for correct operation.

Defective drive motor.
 Replace the drive motor.
C2200
 Drum motor problem
 A stable state does not continue for 1 s from 1 s after the drum motor is activated. Poor contact in the connector terminals.
 Check the connection of connector YC6 on the main/engine PWB and the connector on the drum motor, and the continuity across the connector terminals. Repair or replace if necessary.


Defective drive transmission system.
 Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.

Defective main/engine PWB.
 Replace the main/engine PWB and check for correct operation.

Defective drum motor.
 Replace the drum motor.
C3100
 Scanner carriage problem
 The home position is not correct when the power is turned on or at the start of copying using the table. Poor contact in the connector terminals.
 Check the connection of connector YC5 on the main/engine PWB and the connector on the home position switch, and the continuity across the connector terminals. Repair or replace if necessary.


Defective home position switch.
 Replace the home position switch.

Defective scanner motor.
 Replace the scanner motor.

The mirror frame, exposure lamp, or scanner wire is defective.
 Check if the mirror flames and exposure lamp are on the rail. And check the scanner wire winds correctly.

Defective main/engine PWB.
 Replace the main/engine PWB and check for correct operation.
C3200
 Exposure lamp problem
 Non-lighting of the exposure lamp is detected at the beginning of copying. Poor contact in the connector terminals.
 Check the connection of connector YC16 on the main/engine PWB and the connector on the inverter PWB, and the continuity across the connector terminals. Repair or replace if necessary.


Defective exposure lamp.
 Replace the exposure lamp.

Incorrect shading position.
 Adjust the position of the contact glass (shading plate). If the problem still occurs, replace the home position switch.

Defective PWB.
 Replace the main/engine PWB or inverter PWB and check for correct operation.
C3300
 AGC problem
 After AGC, correct input is not obtained at CCD. Poor contact in the connector terminals.
 Check the connection of connector YC27 on the main/engine PWB and the connector on the CCD PWB, and the continuity across the connector terminals. Repair or replace if necessary.


Defective exposure lamp.
 Replace the exposure lamp.

Defective PWB.
 Replace the main/engine PWB or CCD PWB and check for correct operation.
C4000
 Polygon motor synchronization problem
 The polygon motor does not reach the stable speed within 20 s of the START signal turning on. Poor contact in the connector terminals.
 Check the connection of connector YC3 on the main/engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.


Defective polygon motor.
 Replace the laser scanner unit.

Defective main/engine PWB.
 Replace the main/engine PWB and check for correct operation.
C4010
 Polygon motor steady-state problem
 Stable OFF is detected for 5 s continuously after polygon motor stability. Poor contact in the connector terminals.
 Check the connection of connector YC3 on the main/engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.


Defective polygon motor.
 Replace the laser scanner unit.

Defective main/engine PWB.
 Replace the main/engine PWB and check for correct operation.
C4200
 BD steady-state problem
 ASIC detects a BD error for 600 ms after the polygon motor rotation has been stabilized. Poor contact in the connector terminals.
 Check the connection of connector YC3 on the main/engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.


Defective laser scanner unit.
 Replace the laser scanner unit.

Defective main/engine PWB.
 Replace the main/engine PWB and check for correct operation.
C6000
 Fuser heater break
 The temperature does not reach 70 °C/ 158°F in 15 s before secondary stabilization. Temperature rise of 1°C/1.8°F does not occur in 5 s before secondary stabilization (except during printing). Poor contact in the fuser thermistor connector terminals.
 Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.


Fuser thermistor installed incorrectly.
 Check and reinstall if necessary.

Fuser thermostat triggered.
 Check for continuity. If none, replace the fuser thermostat.

Fuser heater installed incorrectly.
 Check and reinstall if necessary.

Broken fuser heater wire.
 Check for continuity. If none, replace the fuser heater.
C6020
 Abnormally high fuser thermistor temperature
 Fuser thermistor is detected 230°C/ 446°F or more for 40 ms. Shorted thermistor.
 Measure the resistance. If it is 0 Ω, replace the thermistor.


Broken heater control circuit on the power source PWB.
 Replace the power source PWB and check for correct operation.
C6050
 Abnormally low fuser thermistor temperature
 Fuser thermistor remains below 90°C/ 194°F for 1 s. Poor contact in the fuser thermistor connector terminals.
 Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.


Broken fuser thermistor wire.
 Measure the resistance. If it is ∞ Ω, replace the fixing thermistor.

Fuser thermistor installed incorrectly.
 Check and reinstall if necessary.

Fuser thermostat triggered.
 Check for continuity. If none, replace the fuser thermostat.

Fuser heater installed incorrectly.
 Check and reinstall if necessary.

Broken fuser heater wire.
 Check for continuity. If none, replace the fuser heater.
C6400
 Zero-cross signal error
 Interrupt of the zero-cross signal does not occur more than 1 s. Poor contact in the connector terminals.
 Reinsert the connector. Also check for conti- nuity within the connector cable. If none, remedy or replace the cable.


Defective power source PWB.
 Check if the zero-crossing signal is output from YC2-2 on the power source PWB. If not, replace the power source PWB.

Defective main/engine PWB.
 Replace the main/engine PWB if C6400 is detected while YC2-2 on the power source PWB outputs the zero-crossing signal.
C7800
 Broken external thermistor wire
 The thermistor output value is 0.5 V or less. Poor contact in the connector terminals.
 Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.


Defective humidity sensor.
 Replace the cassette PWB and check for correct operation.
C7810
 Short-circuited external thermistor wire
 The thermistor output value is 4.5 V or more. Poor contact in the connector terminals.
 Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.


Defective humidity sensor.
 Replace the cassette PWB and check for correct operation.
C8170*
 Built-in finisher front side registration motor problem
 When the front-side registration home- position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses. When the front-side registration home- position sensor is turned off during initialization, the sensor did not turn on in 3 s. The front side registration motor connector makes poor contact.
 Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.


Defective front side registration motor.
 Replace front side registration motor.

The front side registration home position sensor connector makes poor contact.
 Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.

Defective front side registration home position sensor.
 Replace the front side registration home position sensor.

Defective finisher control PWB.
 Replace the finisher control PWB and check for correct operation.
C8180*
 Built-in finisher rear side registration motor problem
 When the rear-side registration home- position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses. When the rear-side registration home- position sensor is turned off during initialization, the sensor did not turn on in 3 s. The rear side registration motor connector makes poor contact.
 Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.


Defective rear side registration motor.
 Replace rear side registration motor.

The rear side registration home position sensor connector makes poor contact.
 Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.

Defective rear side registration home position sensor.
 Replace the rear side registration home position sensor.

Defective finisher control PWB.
 Replace the finisher control PWB and check for correct operation.
C8190*
 Built-in finisher trailing edge registration motor problem
 When the trailing edge registration home-position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses. When the trailing edge registration home-position sensor is turned off during initialization, the sensor did not turn on in 3 s. The trailing edge registration motor connector makes poor contact.
 Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.


Defective trailing edge registration motor.
 Replace trailing edge registration motor.

The trailing edge registration home position sensor connector makes poor contact.
 Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.

Defective trailing edge registration home position sensor.
 Replace the trailing edge registration home position sensor.

Defective finisher control PWB.
 Replace the finisher control PWB and check for correct operation.
C8210*
 Built-in finisher stapler problem
 The stapler home position sensor does not change state from nondetection to detection within 200 ms of the start of stapler motor counterclockwise (forward) rotation. During initialization, the stapler home position sensor does not change state from non-detection to detection within 600 ms of the start of stapler motor clockwise (reverse) rotation. The stapler connector makes poor contact.
 Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.


The stapler is blocked with a staple.
 Remove the stapler cartridge, and check the cartridge and the stapling section of the stapler.

The stapler is broken.
 Replace the front stapler and check for correct operation.

Defective finisher control PWB.
 Replace the finisher control PWB and check for correct operation.

*) Kyocera TASKalfa 181/221

Источник

– Printer model: Kyocera TASKalfa 180
– Fix Error codes on Kyocera TASKalfa 180 model and its description:

  • Code: A0410
  • Description: Document processor communication problem Communication fails five times succes-sively.
  • Causes: Document processor installed incorrectly.
    Defective PWB
  • Remedy: Document processor installed incorrectly. Check the installation state of the document processor and adjust it if it is not properly installed.
    Defective PWB. Replace the main/engine PWB or DP driver PWB and check for correct operation.
  • Code: A0420
  • Description: First paper feeder communication problem
    Communication fails five times successively.
  • Causes: First paper feeder installed incorrectly.
    Defective PWB
  • Remedy: First paper feeder installed incorrectly. Check the installation state of the first paper feeder and adjust it if it is not properly installed.
    Defective PWB. Replace the main/engine PWB or cassette main PWB and check for correct operation.
  • Code: A0500
  • Description: Second paper feeder communication problem
    Communication fails five times succes-sively
  • Causes: Second paper feeder installed incorrectly.
    Defective PWB
  • Remedy: Second paper feeder installed incorrectly. Check the installation state of the second paper feeder and adjust it if it is not properly installed.
    Defective PWB. Replace the main/engine PWB or cassette main PWB and check for correct operation.
  • Code: A0510
  • Description: Third paper feeder communication problem
    Communication fails five times succes-sively.
  • Causes: Third paper feeder installed incorrectly.
    Defective PWB
  • Remedy: Third paper feeder installed incorrectly. Check the installation state of the third paper feeder and adjust it if it is not properly installed.
    Defective PWB. Replace the main/engine PWB or cassette main PWB and check for correct operation.
  • Code: C0100
  • Description: Backup memory (EEPROM) device problem (main)
    Reading from or writing to EEPROM cannot be performed.
  • Causes: Defective main/ engine PWB.
  • Remedy: Replace the main/engine PWB and check for correct operation.
  • Code: C0110
  • Description: Backup memory data problem (main)
    Data in the specified area of the backup memory does not match the specified values.
  • Causes: Data damage of EEPROM.
  • Remedy: Contact the Service Administrative Division.
  • Code: C0150
  • Description: Backup memory device problem (engine EEPROM)
    Reading from or writing to EEPROM cannot be performed
  • Causes: Defective main/ engine PWB.
    Device damage of EEPROM.
  • Remedy: Defective main/ engine PWB. Replace the main/engine PWB and check for correct operation.
    Device damage of EEPROM. Contact the Service Administrative Division.
  • Code: C0160
  • Description: Backup memory data problem (engine EEPROM)
    Reading data from EEPROM is abnormal.
  • Causes: Data damage of EEPROM.
  • Remedy: Contact the Service Administrative Division.
  • Code: C0170
  • Description: Copy counts problem
    When the power is turned on, the total count and the scan count are abnormal both on the main and engine.
  • Causes: Data damage of EEPROM.
    Defective main/ engine PWB.
  • Remedy: Data damage of EEPROM. Contact the Service Administrative Division.
    Defective main/ engine PWB. Replace the main/engine PWB and check for correct operation.
  • Code: C0180
  • Description: Machine number mismatch
    Machine number of main and engine does not match.
  • Causes: Data damage of EEPROM.
  • Remedy: Contact the Service Administrative Division.
  • Code: C0210
  • Description: Communication problem between the main and engine
    When the power is turned on, the machine does not detect the low level of SBSY and the high level of SDIR for 10 s.
  • Causes: Poor contact in the connector terminals.
    Defective main/ engine PWB.
  • Remedy: Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
    Defective main/ engine PWB. Replace the main/engine PWB and check for correct operation.
  • Code: C0240
  • Description: Printer PWB communication problem
    The printer PWB does not respond 120 s after the power is turned on.
  • Causes: Poor contact in the connector terminals.
    Defective main/ engine PWB.
  • Remedy: Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
    Defective main/ engine PWB. Replace the main/engine PWB and check for correct operation.
  • Code: C0610
  • Description: Bitmap (DIMM) problem
    There is a problem with the data or address bus of the bitmap DRAM.
  • Causes: Defective main/ engine PWB.
    DIMM installed incorrectly.
    Defective DIMM.
  • Remedy: Defective main/ engine PWB. Replace the main/engine PWB and check for correct operation.
    DIMM installed incorrectly. Check if the DIMM is inserted into the socket on the main/engine PWB correctly.
    Defective DIMM. Replace the DIMM and check for correct operation.
  • Code: C0620
  • Description: Memory input interface problem
    Reading-in of an image does not complete within 10 s of the start of image transmission.
  • Causes: Defective main/ engine PWB.
  • Remedy: Defective main/ engine PWB. Replace the main/engine PWB and check for correct operation.
  • Code: C0630
  • Description: DMA problem
    DMA transmission of compressed, decompressed, rotated, relocated or blanked-out image data does not complete within the specified period of time.
  • Causes: Defective main/ engine PWB.
  • Remedy: Defective main/ engine PWB. Replace the main/engine PWB and check for correct operation.
  • Code: C0800
  • Description: Image processing problem
    JAM05 is detected twice.
  • Causes: Defective main/ engine PWB.
  • Remedy: Defective main/ engine PWB. Replace the main/engine PWB and check for correct operation.
  • Code: C2000
  • Description: Drive motor problem
    A stable state does not continue for 1 s from 1 s after the drive motor is activated.
  • Causes: Poor contact in the connector terminals.
    Defective drive transmission system.
    Defective main/ engine PWB.
    Defective drive motor.
  • Remedy: Poor contact in the connector terminals. Check the connection of connector YC6 on the main/engine PWB and the connector on the drive motor, and the continuity across the connector terminals. Repair or replace if necessary.
    Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
    Defective main/ engine PWB. Replace the main/engine PWB and check for correct operation.
    Defective drive motor. Replace the drive motor.
  • Code: C2200
  • Description: Drum motor problem
    A stable state does not continue for 1 s from 1 s after the drum motor is activated.
  • Causes: Poor contact in the connector terminals
    Defective drive transmission system.
    Defective main/ engine PWB.
    Defective drum motor.
  • Remedy: Poor contact in the connector terminals. Check the connection of connector YC6 on the main/engine PWB and the connector on the drum motor, and the continuity across the connector terminals. Repair or replace if necessary.
    Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
    Defective main/ engine PWB. Replace the main/engine PWB and check for correct operation.
    Defective drum motor. Replace the drum motor.
  • Code: C3100
  • Description: Scanner carriage problem
    The home position is not correct when the power is turned on or at the start of copying using the table.
  • Causes: Poor contact in the connector terminals.
    Defective home position switch
    Defective scanner motor
    The mirror frame, exposure lamp, or scanner wire is defective
    Defective main/ engine PWB.
  • Remedy: Poor contact in the connector terminals. Check the connection of connector YC5 on the main/engine PWB and the connector on the home position switch, and the continuity across the connector terminals. Repair or replace if necessary.
    Defective home position switch. Replace the home position switch.
    Defective scanner motor. Replace the scanner motor.
    The mirror frame, exposure lamp, or scanner wire is defective. Check if the mirror flames and exposure lamp are on the rail. And check the scanner wire winds correctly.
    Defective main/ engine PWB. Replace the main/engine PWB and check for correct operation.
  • Code: C3200
  • Description: Exposure lamp problem
    Non-lighting of the exposure lamp is detected at the beginning of copying.
  • Causes: Poor contact in the connector terminals.
    Defective exposure lamp.
    Incorrect shading position.
    Defective PWB
  • Remedy: Poor contact in the connector terminals. Check the connection of connector YC16 on the main/engine PWB and the connector on the inverter PWB, and the continuity across the connector terminals. Repair or replace if necessary.
    Defective exposure lamp. Replace the exposure lamp.
    Incorrect shading position. Adjust the position of the contact glass (shading plate). If the problem still occurs, replace the home position switch.
    Defective PWB. Replace the main/engine PWB or inverter PWB and check for correct operation.
  • Code: C3300
  • Description: AGC problem
    After AGC, correct input is not obtained at CCD
  • Causes: Poor contact in the connector terminals
    Defective exposure lamp.
    Defective PWB
  • Remedy: Poor contact in the connector terminals. Check the connection of connector YC27 on the main/engine PWB and the connector on the CCD PWB, and the continuity across the connector terminals. Repair or replace if necessary.
    Defective exposure lamp. Replace the exposure lamp.
    Defective PWB. Replace the main/engine PWB or CCD PWB and check for correct operation.
  • Code: C4000
  • Description: Polygon motor synchronization problem
    The polygon motor does not reach the stable speed within 20 s of the START signal turning on.
  • Causes: Poor contact in the connector terminals
    Defective polygon motor.
    Defective main/ engine PWB
  • Remedy: Poor contact in the connector terminals. Check the connection of connector YC3 on the main/engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.
    Defective polygon motor. Replace the laser scanner unit.
    Defective main/ engine PWB. Replace the main/engine PWB and check for correct operation.
  • Code: C4010
  • Description: Polygon motor steady-state problem
    Stable OFF is detected for 5 s continuously after polygon motor stability.
  • Causes: Poor contact in the connector terminals.
    Defective polygon motor.
    Defective main/ engine PWB.
  • Remedy: Poor contact in the connector terminals. Check the connection of connector YC3 on the main/engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.
    Defective polygon motor. Replace the laser scanner unit.
    Defective main/ engine PWB. Replace the main/engine PWB and check for correct operation.
  • Code: C4200
  • Description: BD steady-state problem
    ASIC detects a BD error for 600 ms after the polygon motor rotation has been stabilized.
  • Causes: Poor contact in the connector terminals
    Defective laser scanner unit.
    Defective main/ engine PWB
  • Remedy: Poor contact in the connector terminals. Check the connection of connector YC3 on the main/engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.
    Defective laser scanner unit. Replace the laser scanner unit.
    Defective main/ engine PWB. Replace the main/engine PWB and check for correct operation.

Kyocera TASKalfa 180 error code

– Kyocera TASKalfa 180 printer Error Codes and quick guide to troubleshooting:

  • Code: C6000
  • Description: Fuser heater break
    The temperature does not reach 70 °C/ 158°F in 15 s before secondary stabilization.
    Temperature rise of 1°C/1.8°F does not occur in 5 s before secondary stabilization (except during printing).
  • Causes: Poor contact in the fuser thermistor connector terminals.
    Fuser thermistor installed incorrectly.
    Fuser thermostat triggered.
    Fuser heater installed incorrectly.
    Broken fuser heater wire.
  • Remedy: Poor contact in the fuser thermistor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
    Fuser thermistor installed incorrectly. Check and reinstall if necessary.
    Fuser thermostat triggered. Check for continuity. If none, replace the fuser thermostat.
    Fuser heater installed incorrectly. Check and reinstall if necessary.
    Broken fuser heater wire. Check for continuity. If none, replace the fuser heater.
  • Code: C6020
  • Description: Abnormally high fuser thermistor temperature
    Fuser thermistor is detected 230°C/ 446°F or more for 40 ms.
  • Causes: Shorted thermistor.
    Broken heater control circuit on the power source PWB
  • Remedy: Shorted thermistor. Measure the resistance. If it is 0Ω, replace the thermistor.
    Broken heater control circuit on the power source PWB. Replace the power source PWB and check for correct operation.
  • Code: C6050
  • Description: Abnormally low fuser thermistor temperature
    Fuser thermistor remains below 90°C/ 194°F for 1 s.
  • Causes: Poor contact in the fuser thermistor connector terminals.
    Broken fuser thermistor wire.
    Fuser thermistor installed incorrectly.
    Fuser thermostat triggered.
    Fuser heater installed incorrectly.
    Broken fuser heater wire.
  • Remedy: Poor contact in the fuser thermistor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
    Broken fuser thermistor wire. Measure the resistance. If it is ∞, replace the fixing thermistor.
    Fuser thermistor installed incorrectly. Check and reinstall if necessary.
    Fuser thermostat triggered. Check for continuity. If none, replace the fuser thermostat.
    Fuser heater installed incorrectly. Check and reinstall if necessary.
    Broken fuser heater wire. Check for continuity. If none, replace the fuser heater.
  • Code: C6400
  • Description: Zero-cross signal error
    Interrupt of the zero-cross signal does not occur more than 1 s.
  • Causes: Poor contact in the connector terminals
    Defective power source PWB.
    Defective main/ engine PWB.
  • Remedy: Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
    Defective power source PWB. Check if the zero-crossing signal is output from YC2-2 on the power source PWB. If not, replace the power source PWB.
    Defective main/ engine PWB. Replace the main/engine PWB if C6400 is detected while YC2-2 on the power source PWB outputs the zero-crossing signal.
  • Code: C7800
  • Description: Broken external thermistor wire
    The thermistor output value is 0.5 V or less.
  • Causes: Poor contact in the connector terminals.
    Defective humidity sensor.
  • Remedy: Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
    Defective humidity sensor. Replace the cassette PWB and check for correct operation.
  • Code: C7810
  • Description: Short-circuited external thermistor wire
    The thermistor output value is 4.5 V or more.
  • Causes: Poor contact in the connector terminals.
    Defective humidity sensor.
  • Remedy: Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
    Defective humidity sensor. Replace the cassette PWB and check for correct operation.

– Buy WIC Reset key on my online store: https://shop.nguyendangnam.com/product/epson-9900-wic-reset-utility-tool/
– Free Download Epson in specific model: https://dnasofts.com/download-epson-iron-on-kit-driver-firmware-and-manuals/

Source:
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html

Contact us to get support with Kyocera TASKalfa 180 Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/

Источник
  • Code: A0410
  • Description: Document processor communication problem Communication fails five times succes-sively.
  • Causes: Document processor installed incorrectly.
    Defective PWB
  • Remedy: Document processor installed incorrectly. Check the installation state of the document processor and adjust it if it is not properly installed.
    Defective PWB. Replace the main/engine PWB or DP driver PWB and check for correct operation.
  • Code: C0150
  • Description: Backup memory device problem (engine EEPROM)
    Reading from or writing to EEPROM cannot be performed
  • Causes: Defective main/ engine PWB.
    Device damage of EEPROM.
  • Remedy: Defective main/ engine PWB. Replace the main/engine PWB and check for correct operation.
    Device damage of EEPROM. Contact the Service Administrative Division.
  • Code: C0610
  • Description: Bitmap (DIMM) problem
    There is a problem with the data or address bus of the bitmap DRAM.
  • Causes: Defective main/ engine PWB.
    DIMM installed incorrectly.
    Defective DIMM.
  • Remedy: Defective main/ engine PWB. Replace the main/engine PWB and check for correct operation.
    DIMM installed incorrectly. Check if the DIMM is inserted into the socket on the main/engine PWB correctly.
    Defective DIMM. Replace the DIMM and check for correct operation.
  • Code: C3100
  • Description: Scanner carriage problem
    The home position is not correct when the power is turned on or at the start of copying using the table.
  • Causes: Poor contact in the connector terminals.
    Defective home position switch
    Defective scanner motor
    The mirror frame, exposure lamp, or scanner wire is defective
    Defective main/ engine PWB.
  • Remedy: Poor contact in the connector terminals. Check the connection of connector YC5 on the main/engine PWB and the connector on the home position switch, and the continuity across the connector terminals. Repair or replace if necessary.
    Defective home position switch. Replace the home position switch.
    Defective scanner motor. Replace the scanner motor.
    The mirror frame, exposure lamp, or scanner wire is defective. Check if the mirror flames and exposure lamp are on the rail. And check the scanner wire winds correctly.
    Defective main/ engine PWB. Replace the main/engine PWB and check for correct operation.
  • Code: C6000
  • Description: Fuser heater break
    The temperature does not reach 70 °C/ 158°F in 15 s before secondary stabilization.
    Temperature rise of 1°C/1.8°F does not occur in 5 s before secondary stabilization (except during printing).
  • Causes: Poor contact in the fuser thermistor connector terminals.
    Fuser thermistor installed incorrectly.
    Fuser thermostat triggered.
    Fuser heater installed incorrectly.
    Broken fuser heater wire.
  • Remedy: Poor contact in the fuser thermistor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
    Fuser thermistor installed incorrectly. Check and reinstall if necessary.
    Fuser thermostat triggered. Check for continuity. If none, replace the fuser thermostat.
    Fuser heater installed incorrectly. Check and reinstall if necessary.
    Broken fuser heater wire. Check for continuity. If none, replace the fuser heater.
Источник

Понравилась статья? Поделить с друзьями:

Интересное по теме:

  • Куосера сброс ошибки замените мк
  • Куосера сброс ошибки добавьте тонер
  • Куосера ошибка е 017
  • Куосера ошибка jam0509
  • Куосера ошибка j11

    • 0 0 голоса
    Рейтинг статьи
    Подписаться
    Уведомить о
    guest

    0 комментариев
    Старые
    Новые Популярные
    Межтекстовые Отзывы
    Посмотреть все комментарии