Konica minolta ошибка c6102

These instructions describe error code C-6102, c6103, C6104 and C6105 solution for a Konica Minolta bizhub C224e, C284e, and C364e Copier series. We are sharing a few methods to fix the error, so check them one by one until it gets solved.

Field Service Ver. 1.0 Mar. 2005

16.6.76

16.6.77

C6103: Scanner overrun failure

Scanner Home Sensor (PC201)

Scanner Motor (M201)

Step

Correct or change the Scanner drive (cable, pul-

1

ley, gear, belt) if it is faulty.

2

Correct the Scanner Motor set screw if loose.

Adjust «Image Position Leading Edge» and «Feed

3

Direction Adjustment.»

Check the PC201, M201, PWB-IC and PWB-C

4

connector for proper connection and correct as

necessary.

5

PC201 I/O check

M201 operation check

6

7

Change PWB-IC.

8

Change PWB-C.

16.6.78

C6301: Scanner Cooling Fan Motor’s failure to turn

Scanner Cooling Fan Motor (M202)

Step

Check the connector of motor for proper connec-

1

tion and correct as necessary.

Check the fan for possible overload and correct

2

as necessary.

M202 operation check

3

4

Change PWB-MC

Relevant Electrical Parts

Scanner Motor Drive Board (PWB-IC)

Image Processing Board (PWB-C)

Action

Relevant Electrical Parts

Control Board (PWB-MC)

Action

16. Malfunction code

WIRING DIAGRAM

Control Signal

—

—

—

—

PWB-C PJ11C-8 (ON)

PWB-IC PJ3IC-1 (REM)

PWB-IC PJ3IC-3 (LOCK)

—

—

WIRING DIAGRAM

Control Signal

—

—

PWB-C PJ81C-2 (REM)

PWB-C PJ81C-3 (LOCK)

—

Location

(Electrical

Component)

—

—

—

—

N-13

S-9

—

—

Location

(Electrical

Component)

—

—

N-10

—

363

Головна
> Коди помилок Konica Minolta Bizhub C203/253/353 (C6102 — CD004)

Code: C6102

Description:

Drive system home sensor malfunction
• The scanner home sensor is unable to detect the scanner located at its home position. • The scanner home sensor is unable to detect a scanner even when the scanner motor has been driven to move the scanner over the maximum travelling distance. • The scanner home sensor detects the scanner when the scanner has moved the maximum travelling distance from the position, at which it blocks the scanner home sensor.

Remedy:

1 Correct or change the scanner drive (cable, pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the PS201, M201, REYB/SCAN and IPB connector for proper connection and correct as necessary. 5 PS201 I/O check, sensor check. 7 Change REYB/SCAN. 8 Change IPB.

Code: C6103

Description:

Slider over running
• The scanner home sensor detects the scanner at its home position during a period of time that begins with the time when a pre-scan command and a scan preparation command are executed and ends when a home return command is executed.

Remedy:

1 Correct or change the scanner drive (cable, pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the PS201, M201, REYB/SCAN and IPB connector for proper connection and correct as necessary. 5 PS201 I/O check, sensor check. 7 Change REYB/SCAN. 8 Change IPB.

Code: C6301

Description:

Optical cooling fan motor’s failure to turn
• The fan lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary.

Remedy:

1 Check the FM201 connector for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM201 operation check. 4 Change REYB/SCAN. 5 Change IPB.

Code: C6704

Description:

Image input time out
• Image data is not input from the image processing board (IPB) to the printer control board (PRCB).

Remedy:

1 Select [Service Mode] — [State Confirmation] — [Memory/HDD Adj.] — [Memory Bus Check] — [Scanner??Memory], and conduct the memory bus function. 2 Check the connectors between IPB and MFPB for proper connection and correct as necessary. 3 Change MFPB. 4 Change IPB.

Code: C6751

Description:

CCD clamp/gain adjustment failure
• The adjustment value is 0 or 255 during a CCD clamp adjustment. • The peak value of the output data is 64 or less during a CCD gain adjustment.

Remedy:

1 Correct the harness connection between CCDB and IPB if faulty. 2 Check for possible extraneous light and correct as necessary. 3 Clean the lens, mirrors, CCD surface, and shading sheet if dirty 4 Correct reflective mirror of the scanner if faulty, or change scanner. 5 Change CCD sensor unit. 6 Change IPB.

Code: C6F01

Description:

Scanner sequence trouble 1
• The original transport interval becomes shorter than the designed value due to an original transport control error in original reading in ADF.

Remedy:

1 Correct the harness connection between main body and ADF if faulty. 2 Change DFCB. 3 Change MFPB.

Code: C8101

Description:

Before reading pressure welding alienation mechanism

Remedy:

Code: C8102

Description:

Turn around pressure welding alienation trouble

Remedy:

Code: C8103

Description:

Lift up mechanism trouble

Remedy:

Code: C8104

Description:

Glass movement trouble

Remedy:

Code: C8302

Description:

Read cooling fan trouble DF-611

Remedy:

Code: C9401

Description:

Exposure turning on the lamp trouble detection
• The output from the CCD sensor is a predetermined value or less during CCD sensor gain adjustment.

Remedy:

1 Check the connection between the lamp harness and the inverter board, and correct if necessary. 2 Check the connection between REYB/ SCAN and the inverter board, and correct if necessary. 3 Check the connection between REYB/ SCAN and IPB, and correct if necessary. 4 Check that the connection between CCDB and IPB, and correct if necessary. 5 Change INVB. 6 Change scanner assy. 7 Change IPB. 8 Change CCDB. 9 Change REYB/SCAN.

Code: C9402

Description:

Exposure turning on the lamp abnormally detection
• The average output value of the CCD sensor with the scanner at its standby position is a predetermined value or more at the end of a scan job.

Remedy:

1 Check the connection between the lamp harness and the inverter board, and correct if necessary. 2 Check the connection between REYB/ SCAN and the inverter board, and correct if necessary. 3 Check the connection between REYB/ SCAN and IPB, and correct if necessary. 4 Check that the connection between CCDB and IPB, and correct if necessary. 5 Change INVB. 6 Change scanner assy. 7 Change IPB. 8 Change CCDB. 9 Change REYB/SCAN.

Code: CA051

Description:

Standard controller configuration failure
• The controller of the printer control board (PRCB) is faulty

Remedy:

1 Check to see if the following setting has been correctly made: [Service Mode] — [System 2] — [Image Controller Setting]. If changing the setting, turn OFF the main power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFP.

Code: CA052

Description:

Controller hardware error
• A controller hardware error is detected in the network I/F.

Remedy:

1 Check to see if the following setting has been correctly made: [Service Mode] — [System 2] — [Image Controller Setting]. If changing the setting, turn OFF the main power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFP.

Code: CA053

Description:

Controller start failure
• A controller start failure is detected in the controller interface.

Remedy:

1 Check to see if the following setting has been correctly made: [Service Mode] — [System 2] — [Image Controller Setting]. If changing the setting, turn OFF the main power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFP.

Code: CB001

Description:

FAX board error 1

Remedy:

Code: CB002

Description:

FAX board error 2

Remedy:

Code: CB003

Description:

FAX board error 3

Remedy:

Code: CB051

Description:

FAX board mount failure line 1

Remedy:

Code: CB052

Description:

FAX board mount failure line 2

Remedy:

Code: CC001

Description:

Vendor connection failure
• It is detected that communications with the vendor are interrupted for a given period of time or more with “Installed” selected for the setting of vendor installation.

Remedy:

1 Check the vendor connector for proper connection and correct as necessary. 2 Check the PRCB connector for proper connection and correct as necessary. 3 Change PRCB.

Code: CC151

Description:

ROM contents error upon startup (MSC)
• A fault is detected in a sequence of ROM contents check of the MSC (PRCB) during starting

Remedy:

1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the appropriate board.

Code: CC152

Description:

ROM contents error upon startup (scanner)
• A fault is detected in a sequence of ROM contents check of the IPB during starting.

Remedy:

1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the appropriate board.

Code: CC153

Description:

ROM contents error upon startup (PRT)
• A fault is detected in a sequence of ROM contents check of the mechanical control board (MFPB) during starting.

Remedy:

1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the appropriate board.

Code: CC155

Description:

Finisher ROM error

Remedy:

Code: CC156

Description:

ADF ROM error

Remedy:

Code: CC163

Description:

ROM contents error (PRT)
• The wrong model of firmware is detected in the engine during the initial connection to the engine is being checked.

Remedy:

1 Rewrite the firmware. 2 Change PRCB 2.1. Turn OFF the main power switch and replace the current PRCB with a new one. (When using a PRCB of another machine in service, be sure to use a PRCB installed in the same model.) 2.2. Update the PRCB firmware. 2.3. After completing the firmware update, turn OFF and ON the main power switch and check to see that warm-up is started. 2.4. When the trouble cannot be solved, reinstall the removed PRCB to the original board. NOTE • When taking the above steps, check whether PRCB is defective or not without replacing the SV ERB. 3 Change SV ERB 3.1. Replace the current SV ERB with a new one. 3.2. Turn ON the main power switch and check to see that warm-up is started. (One minute is spent to prepare the new SV ERB for use. During the period, the control panel backlight stays off.) 3.3. Make the specified readjustments. 4 If the above actions do not solve the problem, contact KMBT.

Code: CC164

Description:

ROM contents error (MSC)
• The wrong model of firmware is detected in the MFP board when the main power switch is turned ON.

Remedy:

1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the corresponding board. 4 When not reviving even if the above-mentioned procedure is done, contact the responsible people of KMBT.

Code: CC165

Description:

ROM contents error (ADF)

Remedy:

Code: CD002

Description:

JOB RAM save error
• The error in save of JOB data to the memory/ hard disk and its read error are detected.

Remedy:

1 Check the hard disk connector for proper connection and correct as necessary. 2 Format hard disk. 3 Change hard disk. 4 Change MFPB.

Code: CD004

Description:

Hard disk access error

Remedy:

1 Check the hard disk connector for proper connection and correct as necessary. 2 Reinstall the hard disk. 3 Change hard disk. 4 Change MFPB.

Code: CC165

Description:

ROM contents error (ADF)

Remedy:

Code: CD002

Description:

JOB RAM save error
• The error in save of JOB data to the memory/ hard disk and its read error are detected.

Remedy:

1 Check the hard disk connector for proper connection and correct as necessary. 2 Format hard disk. 3 Change hard disk. 4 Change MFPB.

Code: CD004

Description:

Hard disk access error

Remedy:

1 Check the hard disk connector for proper connection and correct as necessary. 2 Reinstall the hard disk. 3 Change hard disk. 4 Change MFPB.

Code: CC165

Description:

ROM contents error (ADF)

Remedy:

Code: CD002

Description:

JOB RAM save error
• The error in save of JOB data to the memory/ hard disk and its read error are detected.

Remedy:

1 Check the hard disk connector for proper connection and correct as necessary. 2 Format hard disk. 3 Change hard disk. 4 Change MFPB.

Code: CD004

Description:

Hard disk access error

Remedy:

1 Check the hard disk connector for proper connection and correct as necessary. 2 Reinstall the hard disk. 3 Change hard disk. 4 Change MFPB.

Code: CC165

Description:

ROM contents error (ADF)

Remedy:

Code: CD002

Description:

JOB RAM save error
• The error in save of JOB data to the memory/ hard disk and its read error are detected.

Remedy:

1 Check the hard disk connector for proper connection and correct as necessary. 2 Format hard disk. 3 Change hard disk. 4 Change MFPB.

Code: CD004

Description:

Hard disk access error

Remedy:

1 Check the hard disk connector for proper connection and correct as necessary. 2 Reinstall the hard disk. 3 Change hard disk. 4 Change MFPB.

Code: CC165

Description:

ROM contents error (ADF)

Remedy:

Code: CD002

Description:

JOB RAM save error
• The error in save of JOB data to the memory/ hard disk and its read error are detected.

Remedy:

1 Check the hard disk connector for proper connection and correct as necessary. 2 Format hard disk. 3 Change hard disk. 4 Change MFPB.

Code: CD004

Description:

Hard disk access error

Remedy:

1 Check the hard disk connector for proper connection and correct as necessary. 2 Reinstall the hard disk. 3 Change hard disk. 4 Change MFPB.