Doosan Fault Codes List.pdf
Adobe Acrobat Document
44.2 KB
HYDRAULIC SYSTEM
Problem Cause Remedy
All organs do not work. Failure of the hydraulic pump. Talk to
control (loud noise of pumps) to the distributor of the company
Doosan.
Not enough hydraulic Add
oils. hydraulic oil as required.
Suction line clogged or Clean or replace
damaged. if necessary.
All organs do not work Failure of the control pump Refer to
control (pump noise is not audible) of the circuit. distributor of the company
Doosan.
Cut-off failure Replace solenoid.
solenoid valve.
Safety end Adjust clearance
the switch is on. travel stop
Low power of all Insufficient hydraulic Add hydraulic
oil drives. oil as needed.
The vacuum filter is clogged. Clean filter.
Failure of hydraulic pumps. Contact your distributor
Doosan company.
Main unload pressure Contact distributor
oil flow is too low. Doosan company.
Hydraulic pumps Bleed air from
excavator. hydraulic pumps.
Power too low or Relief pressure Relieve pressure.
missing for only one or two functions. overload valve too small.
Fill leaks Clean or replace when
check valve. necessity.
Valve spool defective Replace valve spool.
distributor.
Dirt in the valve spool. Clear or replace when
necessity.
Drive failure. Repair or
replace if necessary.
Failure of the cylinder seal. Repair or
replace if necessary.
Cylinder rod damaged. Repair or
replace if necessary.
Remote valve failure Replace the control valve.
management.
Incorrect connection Connect correctly
control lines. control lines.
Oil temperature Defective oil cooler. Contact your distributor
too high. Doosan company.
Fan belt loose. Tighten fan belt
if necessary.
PLATFORM ROTATION SYSTEM
No swing Swing brake valve Replace the brake valve.
defective.
Failure of the hydraulics timer. Replace timer.
Low release pressure Adjust pressure.
brakes.
Swing motor failure. Replace swing motor.
Remote valve failure Replace the control valve.
management.
Incorrect connection Connect correctly
control lines. control lines.
The turn is jerky. Wear of the gearbox of the mechanism Replace the gearbox of the mechanism
turning. turning.
Bearing damaged Replace bearing.
swing mechanism.
Poor lubrication. Add grease.
ELECTRICAL SYSTEM
The battery does not hold Low battery power. Replace batteries.
charge. Alternator belt loose Tighten or replace
or damaged. belt.
Loose or Tighten or replace if
corroded findings. necessity.
Generator malfunction. Repair or
replace if necessary.
Low power Internal short circuit of the battery. Replace battery.
batteries. Short circuit wiring. Renovate.
Engine speed is not Adjustment disk failure Replace adjustment disk
regulated. engine speed. engine speed.
Throttle controller failure. Replace controller.
Speed control failure Repair or
engine. replace if necessary.
Blown fuse. Replace fuse.
Damaged wiring. Repair or
replace if necessary.
12 Indicates the end of one pass through the fault list.
14 ECT sensor input low usually appears if the coolant sensor wire is shorted to ground.
15 ECT sensor input high if the coolant sensor wire is disconnected or wire breakage.
16 ECT coolant temperature too high, measuring excessive temperature or shorted or sitting on ground.
22 Throttle sensor. Input signal wire Input Lo TPS1 is open
23 Throttle valve input sensor TPS1 shorted
24 Throttle sensor sensor TPS. Sensor malfunction
25 Throttle Body Temperature Sensor TPS Sensor Malfunction
26 ETC The ETC sensor supply wire is open or the throttle plate is sticking out inside the throttle body
27 Predicted difference TPS TPS 1 differs from the calculated position
28 ETC early test worked. Throttle spring return error
29 ETC Driver Fault Driver current throttle or driver signals shorted
33 Sensor low signal MAP wire in open circuit or chip open
34 High MAP signal shorted or sensor failure
37 IAT sensor input low, TMAP sensor failure or short circuit
38 IAT sensor input high, TMAP disabled or IAT signal open
42 EST 1. Coil driver low signal low or shorted to positive
43 EST 1. High excitation signal of the coil of high or high current
52 Low engine oil pressure
53 Battery charge sensor input, low battery voltage measured below 8.0 VDC
54 Battery sensor input high battery voltage measured above 15.9 VDC
55 XDRP sensor input sensor low level, below 4.6 VDC
56 Sensor input XDRP sensor high level, above 5.2 VDC
57 The increased engine speed has exceeded the maximum speed setpoint
61 Pedal sensor input 1 Lo APP1 signal disconnected, open circuit or sensor malfunction
62 Pedal sensor input 1 Hi APP1 sensor error or short circuit
63 Pedal sensor range 1 Lo potentiometer APP1
64 Pedal sensor range 1 Hi APP1 potentiometer not working
65 Pedal sensor sensor input Lo APP2 sensor error or short circuit
66 Pedal sensor input 2 Hi APP2 signal disconnected, open circuit or sensor malfunction
67 Pedal sensor range 2 Local malfunction of the potentiometer APP2
68 Pedal sensor range 2 Hi APP2 Potentiometer malfunction
69 Pedal 1. Pedal 2. The difference in the measured signal of the pedal position APP2 differs from APP1
71 AFR Trim Valve Output. FTV Modulation Driver Signal Error
72 Stop valve AFR lower duty cycle FTV at lower limit (LEAN)
73 AFR Trim Valve upper duty cycle DC FTV at the upper (RICH) limit
74 Switching O2 sensor sensor not switching over voltage reference AFR
77 Oxygen sensor input. O2 sensor high signal shorted to +5 VDC
Doosan / Daewoo DH130
Doosan / Daewoo DH170III
Doosan / Daewoo DH220LC
Doosan / Daewoo DH450
Doosan / Daewoo DX140LC
Doosan / Daewoo DX180LC
Doosan / Daewoo DX225LC
Doosan / Daewoo DX255LC
Doosan / Daewoo DX255LCA
Doosan / Daewoo DX300
Doosan / Daewoo DX300LC V
Doosan / Daewoo DX420LC V
Doosan / Daewoo SOLAR 130V
Doosan / Daewoo SOLAR 280LC III
Doosan / Daewoo SOLAR 290V
Doosan / Daewoo SOLAR 330III
Doosan / Daewoo SOLAR 75
Doosan DX140LCR
Doosan DX200A
Doosan DX220A
Doosan DX225LC SLR
Doosan DX225LCA
Doosan DX225NCL
Doosan DX225NLCA
Doosan DX235LCR
Doosan DX235NLC
Doosan DX255LC SLR
Doosan DX260LCA
Doosan DX300LC
Doosan DX300LC SLR
Doosan DX300LC-3
Doosan DX300LCA
Doosan DX340LC
Doosan DX340LC-3
Doosan DX340LCA
Doosan DX380LC
Doosan DX380LC-3
Doosan DX420LC
Doosan DX420LCA
Doosan DX480LC
Doosan DX480LCA-HD
Doosan DX500LCA / 520LCA-HD
Doosan DX520LC
Doosan DX520LC SLR
Doosan DX700LC
Doosan SOLAR 225LC-7
Doosan SOLAR 225NLC-V
Doosan SOLAR 300LC-7
Doosan SOLAR 340LC-V
Doosan SOLAR 500LC-V
An international corporation with a wide range of industries and a network of representative offices around the world. Since acquiring Daewoo Heavy Industries & Machinery in 2005, Doosan has also focused on the construction equipment market.
Then it all started with excavators and wheel loaders. Now the South Korean company Doosan ranks 8th in the world in the production of earthmoving and road construction equipment.
The company’s annual turnover is $ 11 billion. As a result of the transformation, Doosan is progressively pursuing a strategy to achieve leadership in its segment. In 2015, it was ranked 10th in
the world in the production of construction equipment, and in 2016 it climbed 2 levels higher and took 8th place. Doosan expects to become the world’s third largest manufacturer of construction
machinery and equipment after Caterpillar and Komatsu, with annual
sales of $ 12 billion.
The company’s products are excavators, consumer goods, real estate, financial services, IT services, media, retail, industrial equipment and consulting.
In 1977, Daewoo Heavy Industries was established as a division of the South Korean corporation Daewoo. Collaboration with Hitachi launched the production of crawler excavators, which led to the
in-house production of the Solar range after 8 years.
Doosan bought Daewoo Heavy Industries in 2005, which allowed it to strengthen its position in the construction equipment market. Since that time, all equipment began to come under the
Doosan-Daewoo brand. But in 2007, it was decided to promote the technique only under the Doosan brand.
It is worth noting that Doosan Corporation produces a wide range of products, from food and beverage products to engines, heavy equipment and power plants. The construction equipment is handled
by the Doosan Infacore division.
Doosan Infacore is a global corporation with a wide range of industries and a network of representative offices around the world. As noted, the company acquired Daewoo Heavy Industries &
Machinery in 2005, allowing Doosan to enter the construction machinery market. It all started with the release of Doosan excavators and front loaders. At the end of 2010, the South Korean company
ranked 6th in the world in the production of earthmoving and road construction equipment.
DOOSAN Forklift Truck Flash Fault Codes DTC list
DTC — POSSIBLE FAULTS — MALFUNCTIONS * — FIRST CHECK IN METHODS ELIMINATION**
12 None. Indicates the end of one pass through the list faults. NONE*. None, used at the endidentification list faults**
131 Inj1open. Open circuit gasoline injector 1, wire broken injector or defective 1 injector. TurnOnMil*. Check INJ1 wiring for open circuit SECM () A5 signal
to pin A injector 1**. Switched B to pin B 12 injector 1. Check injector resistance* 1, 12-14 ohm (cold)**.
132 Inj2Open. Open circuit gasoline injector 2, wire broken injector or defective 2 injector. TurnOnMil*. Check INJ2 wiring for open circuit SECM () A8 signal
to pin A injector 2. Switched B to pin B 12 injector 2. Check injector resistance 2, 12-14 ohm (cold).**
133 Inj3open. Open circuit gasoline injector 3, wire broken injector silt 3 and defective injector. TurnOnMil*. Check INJ3 wiring for open circuit SECM ()
Signal A4 to pin A injector 3. Switched B to pin 12 B injector 3. Check injector resistance 3, 12-14 ohm (cold)**.
134 Inj4open. Open circuit gasoline injector 4, wire broken injector or defective 4 injector. TurnOnMil*. Check INJ4 wiring for open circuit SECM () Signal
A7 to pin A injector 4. Switched B to pin 12 B injector 4. Check injector resistance 4, 12-14 ohms (cold)**.
141 (14) ECTRangeLow. Refrigerant sensor failure or closed on GND. TurnOnMil*. Check the ECT sensor connector and wiring for short
circuit in GND SECM (). Signal B15 Blvd. 3 to ECT Blvd SECM (GND sensor). Bl. B1 1 to Blvd. Ect SECM (GND System) pin A16, B17**.
151 (15) ECTRangeHigh. Refrigerant sensor disconnected or open circuit. (1) TurnOnMil*. (2) Delayed Engine Shutdown*. (3) Check Engine
Light*. Check if the sensor connector disconnected or for open circuit SECM. Signal B15 Blvd. 3 to ECT Blvd SECM (GND sensor). Bl. B1 .1 to Blvd.**
DOOSAN Forklift Error Flash Codes list
161 (16) ECTOverTempFault. Engine coolant temperature is high Sensor. measured excessive refrigerant temperature, typical due to engine overheating.
(1) TurnOnMil*
(2) DelayedEngine Shutdown*
(3) CheckEngineLight*
Check the refrigerant system by locking the radiator for proper refrigerant level and for leaks in the system. Possible ECT closure to GND, check ECT signal wiring SECM. Signal Bl. B15 .3 to Blt
ECT SECM (GND sensor). Bl B1. 1 to Blvd. SECM (GND System). Blvd A16, B17.Check the regulator for refrigerant leaks**.
171 ECT_IR_Fault. Engine coolant temperature does not change as expected.None*.Check for problems with the refrigerant system such as defective or, viscous
thermostat**.
181 FuelSelectConflict. Signal conflict fuel selection ok install if both of the signals fuel selection closed to the ground. TurnOnMil**. Check connection
fuel selection switch is, whether short to gnd
SECM () SIGNAL A12 pin
SECM (SIGNAL) pin A15
SECM (GND Sensor) pin B1**.
191 CamEdgesFault. No CAM signal, when the engine is like, known rotates, broken sensor crankshaft leads or defective CAM sensor. None*. Check CAM sensor
connections
SECM (SIGNAL) Blvd. B10 to Blvd. 2 CAM sensor
SECM (GND sensor) Bl. Bl. To Bul. 3 CAM sensor
Switched in to the sensor sensor 12 .1 Cam
Check for defective CAM sensor**.
192 CamSyncFault. Loss of sync on CAM sensor, usually due to noise on the signal ordisconnected on CAM sensor. None*. Check CAM sensor connections SECM
(SIGNAL) Blvd. B10 to Blvd. 2
CAM sensor SECM (GND sensor) Bl. Bl. To Bul. 3
CAM sensor Switched in to the sensor sensor 12 .1
Cam Check for defective CAM sensor**.
193 CrankEdgesFault. No signal crankshaft when engine is known, rotates broken, crankshaft sensor leads or defective crankshaft sensor. None*.Check sensor connections
crankshaft
SECM (). SIGNAL Blvd B5 .3 to Blvd.
crankshaft sensor SECM (GND sensor) Bl. B1 .2 to Blvd.
crankshaft sensor Switched in to the sensor sensor 12 .1
crankshaft Check for defective sensor
194 Cranksyncfault. Loss of sync on crankshaft sensor, usually due to noise on signal or discontinuous connection on the sensor crankshaft. None*. Check
sensor connectionscrankshaft
SECM (). SIGNAL Blvd B5 .3 to Blvd.
crankshaft sensor
SECM (GND sensor). Bl. B1 .2 to Blvd.
crankshaft sensor
Switched in to the sensor sensor 12 .1
crankshaft
Check for defective sensor**.
DOOSAN Fault Codes DTC
Doosan Fault Codes DTC
Doosan Fault Codes DTC.pdf
Adobe Acrobat Document
181.9 KB
DOOSAN Excavator Fault Codes List DTC
FAULT CODE — NAME — FAULT DESCRIPTION
12 NONE Signifies the end of one pass through the fault list
14 ECTSensorInputLow Normally set if the coolant sensor wire is shorted to ground
15 ECTSensorInputHigh Set if the coolant sensor wire is disconnected or open
16 ECTRangeHigh Coolant sensor has measured an excessive temperature or shorted to GND
22 ThrottleSensorInputLo TPS1 signal wire is open
23 ThrottleSensorInputHi TPS1 signal wire is shorted
24 ThrottleSensorRangeLo TPS Sensor malfunction
25 ThrottleSensorRangeHi TPS Sensor malfunction
26 ETCSticking ETC driver signal wire is open or the throttle plate is sticking inside the throttle body
27 PredictedTPSDifference TPS1 is different than calculated position
28 ETCSpringTestFailed Throttle return spring failed keyup test
29 ETCDriverFault Throttle driver over-current or driver signals shorted
33 MapSensorInputLow MAP signal disconnected or open circuit
34 MapSensorInputHigh MAP signal shorted or sensor failure
37 IATSensorInputLow TMAP sensor failure or shorted circuit
38 IATSensorInputHigh TMAP disconnected or IAT signal open
42 EST1Low Coil driver signal low or under current
43 EST1High Coil driver signal high or over current
52 LowOilPressure Low engine oil pressure
53 BatterySensorInputLow Battery voltage measured below 8.0 VDC
54 BatterySensorInputHigh Battery voltage measured above 15.9 VDC
55 XDRPSensorInputLow Measured sensor transducer power is below 4.6 VDC
56 XDRPSensorInputHigh Measured sensor transducer power is above 5.2 VDC
57 Engine OverSpeed RPM increased above maximum rpm setpoint
61 Pedal1SensorInputLo APP1 signal disconnected, open circuit or sensor malfunction
62 Pedal1SensorInputHi APP1 sensor failure or shorted circuit
63 Pedal1SensorRangeLo APP1 potentiometer malfunction
64 Pedal1SensorRangeHi APP1 potentiometer malfunction
65 Pedal2SensorInputLo APP2 sensor failure or shorted signal
66 Pedal2SensorInputHi APP2 signal disconnected, open circuit or sensor malfunction
67 Pedal2SensorRangeLo APP2 potentiometer malfunction
68 Pedal2SensorRangeHi APP2 potentiometer malfunction
69 Pedal1ToPedal2Difference Measured APP2 pedal position signal is different than APP1
signal
71 AFRTrimValveOutput FTV modulation driver signal fault
72 AFRTrimValveLowerDC FTV duty cycle at lower (LEAN) limit
73 AFRTrimValveUpperDC FTV duty cycle at upper (RICH) limit
74 O2SensorSwitching O2 sensor not switching across the reference AFR voltage
77 OxygenSensorInputHigh O2 sensor signal shorted to +5 VDC
DX140LC-3 ▪ DX140W-3 ▪ DX170W-3 ▪ DX180LC-3 ▪ DX190W-3 ▪ DX210W-3 ▪ DX210LCR-3 ▪ DX225LC-3 ▪ DX255LC-3
▪ DX300LC-3 ▪ DX340LC-3 ▪ DX350LC-3 ▪ DX380LC-3 ▪ DX700LC-3
12 Indicates the end of one run through the fault list.
14 ECT Sensor Input Low usually occurs if the coolant sensor wire is shorted to ground.
15 ECT sensor input high if the coolant sensor wire is disconnected or the wire is broken.
16 ECT coolant temperature too high, measures excessive temperature or shorted or grounded.
22 Throttle sensor. Open signal input wire InputLo TPS1
23 TPS1 throttle input sensor shorted
24 TPS throttle sensor sensor. Sensor failure
25 Throttle Temperature Sensor TPS Sensor Malfunction
26 ETC ETC sensor supply wire is open or throttle plate is sticking out inside the throttle body
27 Forecast TPS difference TPS 1 differs from calculated position
28 ETC early test worked. Throttle spring return error
29 ETC Driver Fault Current driver throttle or driver signals shorted
33 Sensor low signal MAP wire open or open chip
34 High MAP signal shorted or sensor failure
37 IAT sensor input low, TMAP sensor failure or short circuit
38 IAT sensor input high, TMAP disabled or IAT signal open
42 EST 1. Coil driver signal low or under shorted to positive
43 EST 1. High or high current coil excitation signal
52 Low oil pressure in the engine
53 Battery sensor input, low battery voltage measured below 8.0 VDC
54 Battery sensor input high battery voltage measured above 15.9 VDC
55 XDRP Sensor Input Sensor low, below 4.6V DC
56 XDRP sensor input sensor high, above 5.2 VDC
57 Increased engine speed has exceeded the maximum speed setpoint
61 Pedal sensor input 1 Lo APP1 signal is off, open circuit or sensor failure
62 Pedal sensor input 1 Hi APP1 sensor error or short circuit
63 Pedal sensor range 1 Lo APP1 potentiometer
64 Pedal 1 sensor range Hi APP1 potentiometer not working
65 Pedal sensor sensor input Lo APP2 sensor error or short circuit
66 Pedal sensor input 2 Hi APP2 signal disabled, open circuit or sensor failure
67 Pedal sensor range 2 APP2 potentiometer local fault
68 Pedal 2 sensor range Hi APP2 potentiometer malfunction
69 Pedal 1. Pedal 2. Pedal position measured signal difference APP2 is different from APP1
71 AFR Trim Valve Output. FTV modulation driver signal error
72 Shutoff valve AFR low duty cycle FTV at low limit (LEAN)
73 AFR Trim Valve High Duty Cycle DC FTV at High (RICH) Limit
74 Switching O2 sensor sensor not switching over voltage reference AFR
77 Oxygen sensor input O2 sensor high signal shorted to +5 VDC.
Error Code (DL06 Engine) ◈ The table is a short description for a breakdown occurs in following model. ▪ DX140LC-3 ▪ DX140W-3 ▪ DX170W-3 ▪ DX180LC-3 ▪ DX190W-3 ▪ DX210W-3 ▪ DX210LCR-3 ▪
DX225LC-3 ▪ DX255LC-3
1 V000201 GAUGE PANEL ERROR
2 V000202 E-ECU ERROR
3 V000210 PUMP P/V (A)
4 V000211 PUMP P/V (B)
5 V000212 FLOW CONTROL P/V (C) 2-WAY LH-H
6 V000213 FLOW CONTROL P/V (D) 2-WAY RH-H
7 V000214 FLOW CONTROL P/V (E) ROTATING CW
8 V000215 FLOW CONTROL P/V (F) ROTATING CCW
9 V000216 FLOW CONTROL P/V (G)
10 V000217 PRESS. CONTROL1 P/V (H)
11 V000218 PRESS. CONTROL 2 P/V (I)
12 V000219 FAN CONTROL P/V (J)
13 V000220 TRAVEL STRAIGHT P/V (L)
14 V000221 BOOM CONFLUENCE P/V (M)
15 V000222 ARM CONFLUENCE P/V (N)
16 V000223 BREAKER OPERATING S/V
17 V000224 RELEF PRESS. UP S/V (B)
18 V000225 HIGH SPEED S/V (C)
19 V000226 BREAKER SELECT S/V (D)
20 V000227 REVERSE FAN S/V (E)
21 V000228 CRUISE S/V (F)
22 V000229 FORWARD S/V (G)
23 V000230 REVERSE S/V (H)
24 V000231 2 Pump SELECT S/V (I)
25 V000232 BYPASS CUT OFF S/V (J)
26 V000233 SWING BRAKE RELEASE S/V (K)
27 V000234 STARTER RELAY
28 V000235 BACK BUZZER RELAY
29 V000236 PILOT RELAY
30 V000237 FRONT PUMP PRESS. SENSOR
31 V000238 REAR PUMP PRESS. SENSOR
32 V000239 OWD PRESS. SENSOR
33 V000240 Px(FRONT) PRESS. SENSOR
34 V000241 Py(TRAVEL) PRESS. SENSOR
35 V000242 PARKING BRAKE PRESS. SENSOR
36 V000243 BOOM UP PRESS. SENSOR
37 V000244 BUCKET CR PRESS. SENSOR
38 V000245 BOOM DOWN PRESS. SENSOR
39 V000246 BUCKTET DUMP PRESS. SENSOR
40 V000247 ARM IN PRESS. SENSOR
41 V000248 ARM OUT PRESS. SENSOR
42 V000249 TRAVEL LEFT PRESS. SENSOR
43 V000250 TRAVEL RIGHT PRESS. SENSOR
44 V000251 SWING PRESS. SENSOR
45 V000252 ATT(OPTION) PRESS. SENSOR
46 V000253 OIL TEMP. SENSOR
47 V000254 ACCEL PEDAL SENSOR
48 V000255 VEHICLE SPEED SENSOR
49 V000256 FUEL SENSOR
50 V000257 ALTERNATOR POTENTIAL
51 V000258 DIAL
52 V000259 ANGLE SENSOR (A)
53 V000260 ANGLE SENSOR (B)
54 V000261 WIF SENSOR
55 V000262 ACCEL. PEDAL SWITCH
56 V000263 THUMB WHEEL (RH)
57 V000264 THUMB WHEEL (LH)
58 V000265 INCHING RELAY
59 V000266 LOW SPEED RELAY
60 V000267 HIGH SPEED RELAY
70 E000051 Throttle valve position sensor
71 E000091 Accelerator Pedal Position
72 E000100 Oil pressure sensor
73 E000102 Boost pressure sensor
74 E000108 Barometric pressure sensor in ECU
75 E000110 Coolant temperature
76 E000129 Rail pressure sensor
77 E000132 Air Mass Flow sensor
78 E000157 CP metering unit
79 E000158 Battery
80 E000105 Air Intake Manifold temperature
81 E000173 DPF downstream temperature
82 E000174 Fuel temperature sensor
83 E000175 Oil temperature sensor
84 E000606 Overspeed detection in component engine protection
85 E000734 Solenoid powerstage 1 (Cylinder 1)
86 E000735 Solenoid powerstage 2 (Cylinder 5)
87 E000736 Solenoid powerstage 3 (Cylinder 3)
88 E000737 Solenoid powerstage 4 (Cylinder 6)
89 E000738 Solenoid powerstage 5 (Cylinder 2)
90 E000739 Solenoid powerstage 6 (Cylinder 4)
91 E000977 Auto fan clutch PWM out
92 E001207 Engine ECU Temperature
93 E001322 Monitoring Misfire detection multiple cylinder
94 E001323 Injection Misfire detection cylinder 1
95 E001324 Injection Misfire detection cylinder 5
96 E001325 Injection Misfire detection cylinder 3
97 E001326 Injection Misfire detection cylinder 6
98 E001327 Injection Misfire detection cylinder 2
99 E001328 Injection Misfire detection cylinder 4
100 E001482 Timeout error of CAN receive frame TCU
101 E001639 Auto fan clutch speed
102 E003242 DPF upstream temperature
103 E003464 Throttle valve control
104 E003509 Monitoring of 12V sensor supply voltage in ECU
105 E003609 DPF pressure sensor physical range check
106 E003719 Maximum soot mass in particulate filter
107 E004765 DOC upstream temperature
108 E004767 Diesel oxidation catalyst differential pressure
109 E005456 MU Hydrocarbon doser intake fuel temperature
110 E005465 Pressure control regulator
111 E520196 Rail pressure monitoring
112 E520197 Timeout error of CAN Module C
113 E520199 Crankshaft sensor
114 E520200 Camshaft sensor
115 E520201 EEPROM error
116 E520203 Monitoring of PRV
117 E520206 Timeout error of CAN Module A
118 E520336 Engine temperature sensor plausibility
119 E520602 Hydraulic oil temperature CAN time out
120 E520603 Timeout error of CAN receive frame DEC1V
121 E520604 ECU hardware chip CY146 error
122 E520605 DPM system error
123 E520606 Timeout error of CAN receive frame EGR Valve
124 E520607 EGR valve actuator error
125 E520608 Error message from VGT actuator
126 E520609 Air control governor deviation error
127 E520610 Power stage for intake air heater
128 E520611 Timeout error of CAN receive frame Vehicle cut off switch
129 E520612 Accel pedal CAN Max error
130 E520613 Vehicle cutoff switch error
131 E520614 Timeout error of CAN receive frame VGT
132 E520615 Performance limit activation
133 E520616 ECU power stage test
134 E520617 Metering Unit supply voltage
135 E520618 Monitoring of ADC
136 E520619 Monitoring of communication module
137 E520620 Completely damaged particulate filter
138 E520621 Mon pressure differential characteristics
139 E520622 Disconnected DPF pressure sensor hose line
140 E520623 MU differential pressure MIN
141 E520624 Monitoring of injection
142 E520625 Detection of failed engine start
143 E520626 Injection bank
144 E520628 MU Hydrocarbon dosing valve
145 E520631 MU downstream pressure sensor
146 E520633 ECU power stage module
147 E520636 MU upstream pressure sensor
148 E000172 Air Mass Flow sensor temperature
149 E520637 Actuator relay0 error
150 E520638 Actuator relay1 error
151 E520639 Actuator relay2 error
152 E520640 Actuator relay3 error
153 E520601 ECU hardware chip CY320 error
154 E520641 Monitoring of complete ROM test
155 E520642 ECU shut off path error
156 E520643 Monitoring of overrun
157 E520644 Monitoring of voltage supply
158 E520645 ECU main relay
159 E520646 DPF Pressure sensor hose line check
160 E520647 DPF Pressure sensor offset diagnostic
161 E520651 Monitoring for maximum ash mass in DPF
162 E520648 Monitoring of the engine protection
163 E520649 Monitoring of incomplete regeneration
164 E520650 Regeneration locked
165 E520652 Forced regeneration switch
166 E520653 Forced regeneration inhibit switch
167 E520654 MSC Errors of R2S2
168 E520655 MU Shut off valve
Error Code (DL08 Engine) ◈ The table is a short description for a breakdown occurs in following model. ▪ DX300LC-3 ▪ DX340LC-3 ▪
DX350LC-3
1 V000201 GAUGE PANEL ERROR
2 V000202 E-ECU ERROR
3 V000210 PUMP P/V (A)
4 V000211 PUMP P/V (B)
5 V000212 FLOW CONTROL P/V (C) 2-WAY LH-H
6 V000213 FLOW CONTROL P/V (D) 2-WAY RH-H
7 V000214 FLOW CONTROL P/V (E) ROTATING CW
8 V000215 FLOW CONTROL P/V (F) ROTATING CCW
9 V000216 FLOW CONTROL P/V (G)
10 V000217 PRESS. CONTROL1 P/V (H)
11 V000218 PRESS. CONTROL 2 P/V (I)
12 V000219 FAN CONTROL P/V (J)
13 V000220 TRAVEL STRAIGHT P/V (L)
14 V000221 BOOM CONFLUENCE P/V (M)
15 V000222 ARM CONFLUENCE P/V (N)
16 V000223 BREAKER OPERATING S/V
17 V000224 RELEF PRESS. UP S/V (B)
18 V000225 HIGH SPEED S/V (C)
19 V000226 BREAKER SELECT S/V (D)
20 V000227 REVERSE FAN S/V (E)
21 V000228 CRUISE S/V (F)
22 V000229 FORWARD S/V (G)
23 V000230 REVERSE S/V (H)
24 V000231 2 Pump SELECT S/V (I)
25 V000232 BYPASS CUT OFF S/V (J)
26 V000233 SWING BRAKE RELEASE S/V (K)
27 V000234 STARTER RELAY
28 V000235 BACK BUZZER RELAY
29 V000236 PILOT RELAY
30 V000237 FRONT PUMP PRESS. SENSOR
31 V000238 REAR PUMP PRESS. SENSOR
32 V000239 OWD PRESS. SENSOR
33 V000240 Px(FRONT) PRESS. SENSOR
34 V000241 Py(TRAVEL) PRESS. SENSOR
35 V000242 PARKING BRAKE PRESS. SENSOR
36 V000243 BOOM UP PRESS. SENSOR
37 V000244 BUCKET CR PRESS. SENSOR
38 V000245 BOOM DOWN PRESS. SENSOR
39 V000246 BUCKTET DUMP PRESS. SENSOR
40 V000247 ARM IN PRESS. SENSOR
41 V000248 ARM OUT PRESS. SENSOR
42 V000249 TRAVEL LEFT PRESS. SENSOR
43 V000250 TRAVEL RIGHT PRESS. SENSOR
44 V000251 SWING PRESS. SENSOR
45 V000252 ATT(OPTION) PRESS. SENSOR
46 V000253 OIL TEMP. SENSOR
47 V000254 ACCEL PEDAL SENSOR
48 V000255 VEHICLE SPEED SENSOR
49 V000256 FUEL SENSOR
50 V000257 ALTERNATOR POTENTIAL
51 V000258 DIAL
52 V000259 ANGLE SENSOR (A)
53 V000260 ANGLE SENSOR (B)
54 V000261 WIF SENSOR
55 V000262 ACCEL. PEDAL SWITCH
56 V000263 THUMB WHEEL (RH)
57 V000264 THUMB WHEEL (LH)
58 V000265 INCHING RELAY
59 V000266 LOW SPEED RELAY
60 V000267 HIGH SPEED RELAY
70 E000051 Throttle valve position sensor
71 E000091 Accelerator Pedal Position
72 E000100 Oil pressure sensor
73 E000102 Boost pressure sensor
74 E000108 Barometric pressure sensor in ECU
75 E000110 Coolant temperature
76 E000129 Rail pressure sensor
77 E000132 Air Mass Flow sensor
78 E000157 CP metering unit
79 E000158 Battery
80 E000105 Air Intake Manifold temperature
81 E000173 DPF downstream temperature
82 E000174 Fuel temperature sensor
83 E000175 Oil temperature sensor
84 E000606 Overspeed detection in component engine protection
85 E000734 Solenoid powerstage 1 (Cylinder 1)
86 E000735 Solenoid powerstage 2 (Cylinder 5)
87 E000736 Solenoid powerstage 3 (Cylinder 3)
88 E000737 Solenoid powerstage 4 (Cylinder 6)
89 E000738 Solenoid powerstage 5 (Cylinder 2)
90 E000739 Solenoid powerstage 6 (Cylinder 4)
91 E000977 Auto fan clutch PWM out
92 E001207 Engine ECU Temperature
93 E001322 Monitoring Misfire detection multiple cylinder
94 E001323 Injection Misfire detection cylinder 1
95 E001324 Injection Misfire detection cylinder 5
96 E001325 Injection Misfire detection cylinder 3
97 E001326 Injection Misfire detection cylinder 6
98 E001327 Injection Misfire detection cylinder 2
99 E001328 Injection Misfire detection cylinder 4
100 E001482 Timeout error of CAN receive frame TCU
101 E001639 Auto fan clutch speed
102 E003242 DPF upstream temperature
103 E003464 Throttle valve control
104 E003509 Monitoring of 12V sensor supply voltage in ECU
105 E003609 DPF pressure sensor physical range check
106 E003719 Maximum soot mass in particulate filter
107 E004765 DOC upstream temperature
108 E004767 Diesel oxidation catalyst differential pressure
109 E005456 MU Hydrocarbon doser intake fuel temperature
110 E005465 Pressure control regulator
111 E520196 Rail pressure monitoring
112 E520197 Timeout error of CAN Module C
113 E520199 Crankshaft sensor
114 E520200 Camshaft sensor
115 E520201 EEPROM error
116 E520203 Monitoring of PRV
117 E520206 Timeout error of CAN Module A
118 E520336 Engine temperature sensor plausibility
119 E520602 Hydraulic oil temperature CAN time out
120 E520603 Timeout error of CAN receive frame DEC1V
121 E520604 ECU hardware chip CY146 error
122 E520605 DPM system error
123 E520606 Timeout error of CAN receive frame EGR Valve
124 E520607 EGR valve actuator error
125 E520608 Error message from VGT actuator
126 E520609 Air control governor deviation error
127 E520610 Power stage for intake air heater
128 E520611 Timeout error of CAN receive frame Vehicle cut off switch
129 E520612 Accel pedal CAN Max error
130 E520613 Vehicle cutoff switch error
131 E520614 Timeout error of CAN receive frame VGT
132 E520615 Performance limit activation
133 E520616 ECU power stage test
134 E520617 Metering Unit supply voltage
135 E520618 Monitoring of ADC
136 E520619 Monitoring of communication module
137 E520620 Completely damaged particulate filter
138 E520621 Mon pressure differential characteristics
139 E520622 Disconnected DPF pressure sensor hose line
140 E520623 MU differential pressure MIN
141 E520624 Monitoring of injection
142 E520625 Detection of failed engine start
143 E520626 Injection bank
144 E520628 MU Hydrocarbon dosing valve
145 E520631 MU downstream pressure sensor
146 E520633 ECU power stage module
147 E520636 MU upstream pressure sensor
148 E000172 Air Mass Flow sensor temperature
149 E520637 Actuator relay0 error
150 E520638 Actuator relay1 error
151 E520639 Actuator relay2 error
152 E520640 Actuator relay3 error
153 E520601 ECU hardware chip CY320 error
154 E520641 Monitoring of complete ROM test
155 E520642 ECU shut off path error
156 E520643 Monitoring of overrun
157 E520644 Monitoring of voltage supply
158 E520645 ECU main relay
159 E520646 DPF Pressure sensor hose line check
160 E520647 DPF Pressure sensor offset diagnostic
161 E520651 Monitoring for maximum ash mass in DPF
162 E520648 Monitoring of the engine protection
163 E520649 Monitoring of incomplete regeneration
164 E520650 Regeneration locked
165 E520652 Forced regeneration switch
166 E520653 Forced regeneration inhibit switch
167 E520654 MSC Errors of R2S2
168 E520655 MU Shut off valve
Error Code (Cummins Engine) ◈ The following is a short description for a breakdown occurs in DX140LCR-3 model.
1 V000201 GAUGE PANEL ERROR
2 V000202 E-ECU ERROR
3 V000210 PUMP P/V (A)
4 V000212 FLOW CONTROL P/V (C) 2-WAY LH-H
5 V000213 FLOW CONTROL P/V (D) 2-WAY RH-H
6 V000214 FLOW CONTROL P/V (E) ROTATING CW
7 V000215 FLOW CONTROL P/V (F) ROTATING CCW
8 V000216 FLOW CONTROL P/V (G)
9 V000217 PRESS. CONTROL1 P/V (H)
10 V000218 PRESS. CONTROL 2 P/V (I)
11 V000219 FAN CONTROL P/V (J)
12 V000223 BREAKER OPERATING S/V
13 V000224 RELIEF PRESS. UP S/V (B)
14 V000225 HIGH SPEED S/V (C)
15 V000234 STARTER RELAY
16 V000235 BACK BUZZER RELAY
17 V000237 FRONT PUMP PRESS. SENSOR
18 V000238 REAR PUMP PRESS. SENSOR
19 V000239 OWD PRESS. SENSOR
20 V000240 Px(FRONT) PRESS. SENSOR
21 V000241 Py(TRAVEL) PRESS. SENSOR
22 V000253 OIL TEMP. SENSOR
23 V000256 FUEL SENSOR
24 V000257 ALTERNATOR POTENTIAL
25 V000258 DIAL
26 V000261 WIF SENSOR
27 V000263 THUMB WHEEL (RH)
28 V000264 THUMB WHEEL (LH)
29 E000100 E/G OIL PRESSURE SENSOR
30 E000102 Boost pressure sensor
31 E000103 Turbocharger #1 speed
32 E000105 Intake manifold temperature sensor
33 E000108 Barometric pressure sensor
34 E000110 Coolant temperature sensor
35 E000157 Injector metering rail 1 press. sensor circuit
36 E000168 Battery voltage
37 E000190 E/G SPEED SENSOR
38 E000412 Exhaust gas recirculation(EGR) temperature
39 E000611 intermediate speed switch validation
40 E000612 E/G magnetic pickup. speed/position lost both signals
41 E000627 POWER SUPPLY
42 E000629 ECU critical internal failure
43 E000633 fueling actuator #1 circuit error
44 E000639 CAN communication error
45 E000640 Engine external protection input
46 E000647 FAN clutch control circuit
47 E000651 Injector solenoid driver cylinder 1 circuit
48 E000652 Injector solenoid driver cylinder 2 circuit
49 E000653 Injector solenoid driver cylinder 3 circuit
50 E000654 Injector solenoid driver cylinder 4 circuit
51 E000655 Injector solenoid driver cylinder 5 circuit
52 E000656 Injector solenoid driver cylinder 6 circuit
53 E000723 Engine speed sensor error
54 E000729 Intake air heater 1 circuit
55 E001075 Electric lift pump control signal for E/G fuel
56 E001136 sensor circuit-voltage
57 E001172 Turbocharger #1 compressor inlet temperature
58 E001209 Exhaust gas pressure
59 E001347 Fuel pump pressurizing assembly 1
60 E002789 Turbocharger turbine inlet temperature
61 E003509 Sensor supply voltage 1 circuit
62 E003510 Sensor supply 2 circuit
63 E003511 Sensor supply 3 circuit
Error Code (ISUZU Engine) ◈ The table is a short description for a breakdown occurs in following model. DX420LC-3, DX490LC-3
1 V000201 GAUGE PANEL ERROR
2 V000202 E-ECU ERROR
3 V000210 PUMP P/V (A)
4 V000211 PUMP P/V (B)
5 V000212 FLOW CONTROL P/V (C) 2-WAY LH-H
6 V000213 FLOW CONTROL P/V (D) 2-WAY RH-H
7 V000214 FLOW CONTROL P/V (E) ROTATING CW
8 V000215 FLOW CONTROL P/V (F) ROTATING CCW
9 V000216 FLOW CONTROL P/V (G)
10 V000217 PRESS. CONTROL1 P/V (H)
11 V000218 PRESS. CONTROL 2 P/V (I)
12 V000219 FAN CONTROL P/V (J)
13 V000220 TRAVEL STRAIGHT P/V (L)
14 V000221 BOOM CONFLUENCE P/V (M)
15 V000222 ARM CONFLUENCE P/V (N)
16 V000223 BREAKER OPERATING S/V
17 V000224 RELEF PRESS. UP S/V (B)
18 V000225 HIGH SPEED S/V (C)
19 V000226 BREAKER SELECT S/V (D)
20 V000227 REVERSE FAN S/V (E)
21 V000228 CRUISE S/V (F)
22 V000229 FORWARD S/V (G)
23 V000230 REVERSE S/V (H)
24 V000231 2 Pump SELECT S/V (I)
25 V000232 BYPASS CUT OFF S/V (J)
26 V000233 SWING BRAKE RELEASE S/V (K)
27 V000234 STARTER RELAY
28 V000235 BACK BUZZER RELAY
29 V000236 PILOT RELAY
30 V000237 FRONT PUMP PRESS. SENSOR
31 V000238 REAR PUMP PRESS. SENSOR
32 V000239 OWD PRESS. SENSOR
33 V000240 Px(FRONT) PRESS. SENSOR
34 V000241 Py(TRAVEL) PRESS. SENSOR
35 V000242 PARKING BRAKE PRESS. SENSOR
36 V000243 BOOM UP PRESS. SENSOR
37 V000244 BOOM DOWN PRESS. SENSOR
38 V000245 BUCKET CR PRESS. SENSOR
39 V000246 BUCKTET DUMP PRESS. SENSOR
40 V000247 ARM IN PRESS. SENSOR
41 V000248 ARM OUT PRESS. SENSOR
42 V000249 TRAVEL LEFT PRESS. SENSOR
43 V000250 TRAVEL RIGHT PRESS. SENSOR
44 V000251 SWING PRESS. SENSOR
45 V000252 ATT(OPTION) PRESS. SENSOR
46 V000253 OIL TEMP. SENSOR
47 V000254 ACCEL PEDAL SENSOR
48 V000255 VEHICLE SPEED SENSOR
49 V000256 FUEL SENSOR
50 V000257 ALTERNATOR POTENTIAL
51 V000258 DIAL
52 V000259 ANGLE SENSOR (A)
53 V000260 ANGLE SENSOR (B)
54 V000261 WIF SENSOR
55 V000262 ACCEL. PEDAL SWITCH
56 V000263 THUMB WHEEL (RH)
57 V000264 THUMB WHEEL (LH)
58 V000265 INCHING RELAY
59 V000266 LOW SPEED RELAY
60 V000267 HIGH SPEED RELAY
71 E000091 Accelerator Pedal Position Fault
72 E000100 Engine Oil Pressure Sensor Fault
73 E000102 Boost Pressure Sensor Fault
74 E000108 Baro Sensor Fault
75 E000110 Coolant Temperature Sensor Fault
76 E000129 Not Defined
77 E000132 MAF Sensor Fault
78 E000157 Common Rail Pressure Sensor Fault
79 E000158 System Power Supply Voltage Fault
80 E000105 Boost Temperature Sensor Fault
81 E000173 Exhaust Temperature Sensor Fault
82 E000174 Fuel Temperature Sensor Fault
148 E000172 Inlet Air Temperature Sensor Fault
180 E000081 DPF Differential Pressure High
181 E000190 Overrun
182 E000628 ROM Fault
183 E000633 Pressure Limiter Open
184 E000636 G Sensor Fault
185 E000639 CAN Bus Fault
186 E000651 Injection Nozzle #1Drive System Open Circuit Fault
187 E000652 Injection Nozzle #2Drive System Open Circuit Fault
188 E000653 Injection Nozzle #3Drive System Open Circuit Fault
189 E000654 Injection Nozzle #4Drive System Open Circuit Fault
190 E000655 Injection Nozzle #5Drive System Open Circuit Fault
191 E000656 Injection Nozzle #6Drive System Open Circuit Fault
192 E000675 Glow Plug Fault
193 E000676 Glow Relay Fault
194 E000677 Starter Cut Relay Fault
195 E000723 Crank Sensor Fault
196 E000968 Idle Speed Up-Down Switch Fault
197 E000987 Check Engine Lamp Fault
198 E001077 CPU Fault
199 E001079 5V Power Supply-6 Voltage Fault
200 E001080 5V Power Supply-2 Voltage Fault
201 E001131 Manifold Temperature Sensor Fault
202 E001239 Common Rail Pressure Fault (Lack of Feed 1)
203 E001240 Common Rail Pressure Fault (Lack of Feed 2)
204 E001347 PCV 1 Drive System Fault
205 E001348 PCV 2 Drive System Fault
206 E001381 Fuel Filter Clogging Sensor Fault
207 E002791 EGR Gas flow Fault
208 E010001 EGR Position Sensor Fault
209 E010002 EGR Valve Control Fault
210 E010003 Injection Nozzle Common 1 Drive System Fault
211 E010004 Injection Nozzle Common 2 Drive System Fault
212 E010005 Charge Circuit Fault （Bank 1）
213 E010006 Charge Circuit Fault （Bank 2）
214 E010007 CPU Monitoring IC Fault
215 E010008 A/D Conversion Fault
216 E010009 5V Power Supply-3 Voltage Fault
217 E010010 5V Power Supply-4 Voltage Fault
218 E010011 5V Power Supply-5 Voltage Fault
219 E010012 12V Power Supply Voltage Fault
220 E010013 EEPROM Fault
221 E010014 EGR Gas Temperature Sensor Fault
222 E010020 EGR 2 Valve Control Fault
223 E010021 EGR 2 Position Sensor Fault
224 E010022 Intake Throttle Fault
225 E010023 EVRV Vacuum Sensor Fault
226 E010024 Exhaust Temperature Sensor 2 Fault
227 E010025 DPF Lamp Fault
228 E010026 DPF PM Over
229 E010027 DPF Regeneration Defective
230 E010028 DPF Exhaust Temperature 2
231 E010029 DPF Regeneration Timeout Excess Frequency
232 E010030 Starter Deterioration Warning
233 E010031 Starter Switch Fault
234 E010032 QR Code Error
235 E010033 RAM Fault
236 E010036 VGS 1 M/V Fault
237 E010037 VGS 2 M/V Fault
238 E010038 VGS 3 M/V Fault
239 E010039 VGS Relay Fault
240 E010040 ISO-CAN Bus Fault
Error Code (WheelLoader) ◈ The table is a short description for a breakdown occurs in following model. H200, H250, H300, H350, H400, H450,
H550
1 V001 Gauge Panel Communication
2 V002 ECU Communication
3 V003 TCU Communication
4 V004 Electric Steering Communication
10 V010 Cooling Fan Proportional Valve
11 V011 Auxiliary Proportional Valve
12 V012 Electronic MCV Boom Raise Proportional Valve
13 V013 Electronic MCV Boom Float Proportional Valve
14 V014 Electronic MCV Bucket Crowd Proportional Valve
15 V015 Electronic MCV Bucket Dump Proportional Valve
16 V016 Electronic MCV Option Proportional Valve1
17 V017 Electronic MCV Option Proportional Valve2
18 V018 Reverse Fan Solenoid Valve
19 V019 Unloading Solenoid Valve
20 V020 Auxiliary Solenoid Valve 2
21 V022 Starter Relay
22 V023 Main Pump Pressure Sensor
23 V024 Steering Pump Pressure Sensor
24 V025 Boom Angle Sensor
25 V026 Bucket Angle Sensor
26 V027 Electronic MCV Boom Joystick
27 V028 Electronic MCV Bucket Joystick
28 V029 Electronic MCV Option Joystick
29 V030 Electric Steering Joystick
30 V031 Alternator Potential
31 V032 Boom Magnet
32 V033 Reserved Magnet
33 V034 Return to Dig Magnet
34 V035 Water In Fuel Sensor
35 V036 Brake Oil Pressure Sensor
36 V037 Accel Pedal
37 V038 Power Mode Foot Switch
70 E001 Engine Throttle Position
71 E002 Engine Fuel Delivery Pressure
72 E003 Engine Oil Level
73 E004 Engine Oil Pressure
74 E005 Engine Intake Manifold #1 Pressure
75 E006 Engine Intake Manifold 1 Temperature
76 E007 Engine Air Filter 1 Differential Pressure
77 E008 Barometric Pressure
78 E009 Engine Coolant Temperature
79 E010 Engine Coolant Level
80 E011 Engine Injector Timing Rail 1 Pressure
81 E012 Charging System Potential (Voltage)
82 E013 Battery Potential / Power Input 1
83 E014 Ambient Air Temperature
84 E015 Engine Speed
85 E016 Accelerator Pedal Kickdown Switch
86 E017 Engine Idle Shutdown Timer State
87 E018 Engine Position Sensor
88 E019 Engine Injector Cylinder #01
89 E020 Engine Injector Cylinder #02
90 E021 Engine Injector Cylinder #03
91 E022 Engine Injector Cylinder #04
92 E023 Engine Injector Cylinder #05
93 E024 Engine Injector Cylinder #06
94 E025 Engine Injector Cylinder #07
95 E026 Engine Injector Cylinder #08
96 E027 Engine Starter Motor Relay
97 E028 Requested Percent Fan Speed
98 E029 Engine Protection System has Shutdown Engine
99 E030 Engine Fuel Leakage 1
100 E031 Engine Misfire for Multiple Cylinders
101 E032 Engine Misfire Cylinder #1
102 E033 Engine Misfire Cylinder #2
103 E034 Engine Misfire Cylinder #3
104 E035 Engine Misfire Cylinder #4
105 E036 Engine Misfire Cylinder #5
106 E037 Engine Misfire Cylinder #6
107 E038 Engine Misfire Cylinder #7
108 E039 Engine Misfire Cylinder #8
109 E040 Engine Fuel Valve 1 Position
110 E041 Source Address of Controlling Device for Engine Control
111 E042 Engine Torque Limit Feature
112 E043 Fan Speed
113 E044 Aftertreatment 1 SCR Catalyst Tank Level
114 E045 Engine Injector Group 1
115 E046 Engine Injector Group 2
116 E047 Aftertreatment 1 SCR Catalyst Tank Temperature
117 E048 Aftertreatment 1 Outlet NOx
118 E049 Aftertreatment 1 Exhaust Gas Temperature 1
119 E050 Aftertreatment 1 SCR Catalyst Tank Controller
120 E051 Aftertreatment 1 SCR Catalyst Dosing Unit
121 E052 Aftertreatment 1 SCR Catalyst Tank Heater
122 E053 NOx limits exceeded, root cause unknown
123 E054 NOx limits exceeded due to Interrupted Reagent Dosing
124 E055 NOx limits exceeded due to Empty Reagent Tank
125 E056 Aftertreatment 1 SCR Dosing Reagent Absolute Pressure
126 E057 Aftertreatment 1 SCR Dosing Reagent Temperature
127 E058 Aftertreatment 1 SCR Catalyst Reagent Line Heater 1 Preliminary FMI
128 E059 Aftertreatment 1 SCR Catalyst Reagent Pump Motor Speed
150 E000051 Throttle valve position sensor
151 E000091 Accelerator Pedal Position
152 E000100 Oil pressure sensor
153 E000102 Boost pressure sensor
154 E000108 Barometric pressure sensor in ECU
155 E000110 Coolant temperature
156 E000129 Rail pressure sensor
157 E000132 Air Mass Flow sensor
158 E000157 CP metering unit
159 E000158 Battery
160 E000105 Air Intake Manifold temperature
161 E000173 DPF downstream temperature
162 E000174 Fuel temperature sensor
163 E000175 Oil temperature sensor
164 E000606 Overspeed detection in component engine protection
165 E000734 Solenoid powerstage 1 (Cylinder 1)
166 E000735 Solenoid powerstage 2 (Cylinder 5)
167 E000736 Solenoid powerstage 3 (Cylinder 3)
168 E000737 Solenoid powerstage 4 (Cylinder 6)
169 E000738 Solenoid powerstage 5 (Cylinder 2)
170 E000739 Solenoid powerstage 6 (Cylinder 4)
171 E000977 Auto fan clutch PWM out
172 E001207 Engine ECU Temperature
173 E001322 Monitoring Misfire detection multiple cylinder
174 E001323 Injection Misfire detection cylinder 1
175 E001324 Injection Misfire detection cylinder 5
176 E001325 Injection Misfire detection cylinder 3
177 E001326 Injection Misfire detection cylinder 6
178 E001327 Injection Misfire detection cylinder 2
179 E001328 Injection Misfire detection cylinder 4
180 E001482 Timeout error of CAN receive frame TCU
181 E001639 Auto fan clutch speed
182 E003242 DPF upstream temperature
183 E003464 Throttle valve control
184 E003509 Monitoring of 12V sensor supply voltage in ECU
185 E003609 DPF pressure sensor physical range check
186 E003719 Maximum soot mass in particulate filter
187 E004765 DOC upstream temperature
188 E004767 Diesel oxidation catalyst differential pressure
189 E005456 MU Hydrocarbon doser intake fuel temperature
190 E005465 Pressure control regulator
191 E520196 Rail pressure monitoring
192 E520197 Timeout error of CAN Module C
193 E520199 Crankshaft sensor
194 E520200 Camshaft sensor
195 E520201 EEPROM error
196 E520203 Monitoring of PRV
197 E520206 Timeout error of CAN Module A
198 E520336 Engine temperature sensor plausibility
199 E520602 Hydraulic oil temperature CAN time out
200 E520603 Timeout error of CAN receive frame DEC1V
201 E520604 ECU hardware chip CY146 error
202 E520605 DPM system error
203 E520606 Timeout error of CAN receive frame EGR Valve
204 E520607 EGR valve actuator error
205 E520608 Error message from VGT actuator
206 E520609 Air control governor deviation error
207 E520610 Power stage for intake air heater
208 E520611 Timeout error of CAN receive frame Vehicle cut off switch
209 E520612 Accel pedal CAN Max error
210 E520613 Vehicle cutoff switch error
211 E520614 Timeout error of CAN receive frame VGT
212 E520615 Performance limit activation
213 E520616 ECU power stage test
214 E520617 Metering Unit supply voltage
215 E520618 Monitoring of ADC
216 E520619 Monitoring of communication module
217 E520620 Completely damaged particulate filter
218 E520621 Mon pressure differential characteristics
219 E520622 Disconnected DPF pressure sensor hose line
220 E520623 MU differential pressure MIN
221 E520624 Monitoring of injection
222 E520625 Detection of failed engine start
223 E520626 Injection bank
224 E520628 MU Hydrocarbon dosing valve
225 E520631 MU downstream pressure sensor
226 E520633 ECU power stage module
227 E520636 MU upstream pressure sensor
228 E000172 Air Mass Flow sensor temperature
229 E520637 Actuator relay0 error
230 E520638 Actuator relay1 error
231 E520639 Actuator relay2 error
232 E520640 Actuator relay3 error
233 E520601 ECU hardware chip CY320 error
234 E520641 Monitoring of complete ROM test
235 E520642 ECU shut off path error
236 E520643 Monitoring of overrun
237 E520644 Monitoring of voltage supply
238 E520645 ECU main relay
239 E520646 DPF Pressure sensor hose line check
240 E520647 DPF Pressure sensor offset diagnostic
241 E520651 Monitoring for maximum ash mass in DPF
242 E520648 Monitoring of the engine protection
243 E520649 Monitoring of incomplete regeneration
244 E520650 Regeneration locked
245 E520652 Forced regeneration switch
246 E520653 Forced regeneration inhibit switch
247 E520654 MSC Errors of R2S2
248 E520655 MU Shut off valve
249 E000015 Engine shut off request from EPOS
250 E000093 Engine error lamp
251 E000094 ECU reset
300 T010 LOGICAL ERROR AT DIRECTION SELECT SIGNAL 3RD SHIFT LEVER
301 T011 LOGICAL ERROR AT GEAR RANGE SIGNAL
302 T012 LOGICAL ERROR AT DIRECTION SELECT SIGNAL
303 T013 LOGICAL ERROR AT ENGINE DERATING DEVICE
304 T014 LOGICAL ERROR AT PARKBRAKE STATUS
305 T015 LOGICAL ERROR AT DIRECTION SELECT SIGNAL 2. SHIFT LEVER
306 T016 LOGICAL ERROR AT AXLE CONNECTION
307 T021 S.C. TO BATTERY VOLTAGE AT CLUTCH CUTOFF / INCHPEDAL INPUT
308 T022 S.C. TO GROUND OR O.C. AT CLUTCH CUTOFF / INCHPEDAL INPUT
309 T025 S.C. TO BATTERY VOLTAGE OR O.C. AT T/M SUMP TEMP. SENSOR INPUT
310 T026 S.C. TO GROUND AT T/M SUMP TEMP. SENSOR INPUT
311 T027 S.C. TO BATTERY VOLTAGE OR O.C. AT TORQUECvt. TEMP. SENSOR INPUT
312 T028 S.C. TO GROUND AT TORQUECONVERTER TEMP.SENSOR INPUT
313 T031 S.C. TO BATTERY VOLTAGE OR O.C. AT ENGINE SPEED INPUT
314 T032 S.C. TO GROUND AT ENGINE SPEED INPUT
315 T033 LOGICAL ERROR AT ENGINE SPEED INPUT
316 T034 S.C. TO BATTERY VOLTAGE OR O.C. AT TURBINE SPEED INPUT
317 T035 S.C. TO GROUND AT TURBINE SPEED INPUT
318 T036 LOGICAL ERROR AT TURBINE SPEED INPUT
319 T037 S.C. TO BATTERY VOLTAGE OR O.C. AT INTERNAL SPEED INPUT
320 T038 S.C. TO GROUND AT INTERNAL SPEED INPUT
321 T039 LOGICAL ERROR AT INTERNAL SPEED INPUT
322 T03A S.C. TO BATTERY VOLTAGE OR O.C. AT OUTPUT SPEED INPUT
323 T03B S.C. TO GROUND AT OUTPUT SPEED INPUT
324 T03C LOGICAL ERROR AT OUTPUT SPEED INPUT
325 T03E OUTPUT SPEED ZERO DOESN’T FIT TO OTHER SPEED SIGNALS
326 T054 VEHICLE_1 TIMEOUT
327 T055 JSS TIMEOUT
328 T056 ENGINE CONF TIMEOUT
329 T057 EEC1 TIMEOUT
330 T058 EEC3 TIMEOUT
331 T061 AEB REQUEST SIGNAL
332 T065 ENGINE TORQUE SIGNAL
333 T069 REFERENCE ENGINE TORQUE SIGNAL
334 T06A ACTUAL ENGINE TORQUE SIGNAL
335 T06B NOM FRICTION TORQUE SIGNAL
336 T06E EEC2 TIMEOUT
337 T071 S.C. TO BATTERY VOLTAGE AT CLUTCH K1
338 T072 S.C. TO GROUND AT CLUTCH K1
339 T073 O.C. AT CLUTCH K1
340 T074 S.C. TO BATTERY VOLTAGE AT CLUTCH K2
341 T075 S.C. TO GROUND AT CLUTCH K2
342 T076 O.C. AT CLUTCH K2
343 T077 S.C. TO BATTERY VOLTAGE AT CLUTCH K3
344 T078 S.C. TO GROUND AT CLUTCH K3
345 T079 O.C. AT CLUTCH K3
346 T07A S.C. TO BATTERY VOLTAGE AT CONVERTER CLUTCH
347 T07B S.C. TO GROUND AT CONVERTER CLUTCH
348 T07C O.C. AT CONVERTER CLUTCH
349 T081 S.C. TO BATTERY VOLTAGE AT CLUTCH K4
350 T082 S.C. TO GROUND AT CLUTCH K4
351 T083 O.C. AT CLUTCH K4
352 T084 S.C. TO BATTERY VOLTAGE AT CLUTCH KV
353 T085 S.C. TO GROUND AT CLUTCH KV
354 T086 O.C. AT CLUTCH KV
355 T087 S.C. TO BATTERY VOLTAGE AT CLUTCH KR
356 T088 S.C. TO GROUND AT CLUTCH KR
357 T089 O.C. AT CLUTCH KR
358 T08A S.C. TO GROUND AT DHL VALVE OUTPUT
359 T08B S.C. TO BATTERY VOLTAGE AT DHL VALVE OUTPUT
360 T08C O.C. AT DHL VALVE OUTPUT
361 T091 S.C. TO GROUND AT RELAY REVERSE WARNING ALARM
362 T092 S.C. TO BATTERY VOLTAGE AT RELAY REVERSE WARNING ALARM
363 T093 O.C. AT RELAY REVERSE WARNING ALARM
364 T09A S.C. TO GROUND AT CONVERTER LOCK UP CLUTCH SOLENOID
365 T09B O.C. AT CONVERTER LOCK UP CLUTCH SOLENOID
366 T09C S.C. TO BATTERY VOLTAGE AT CONVERTER LOCK UP CLUTCH SOLENOID
367 T0A7 S.C. TO GROUND AT LIS OUTPUT
368 T0A8 S.C. TO BATTERY VOLTAGE AT LIS OUTPUT
369 T0A9 O.C. AT LIS OUTPUT
370 T0B1 SLIPPAGE AT CLUTCH K1
371 T0B2 SLIPPAGE AT CLUTCH K2
372 T0B3 SLIPPAGE AT CLUTCH K3
373 T0B4 SLIPPAGE AT CLUTCH K4
374 T0B5 SLIPPAGE AT CLUTCH KV
375 T0B6 SLIPPAGE AT CLUTCH KR
376 T0B7 OVERTEMP SUMP
377 T0BA DIFFERENTIAL PRESSURE OIL FILTER
378 T0BB SLIPPAGE AT CONVERTER LOCKUP CLUTCH
379 T0BC OVERSPEED OUTPUT
380 T0C0 ENGINE TORQUE OR ENGINE POWER
381 T0C1 TRANSMISSION OUTPUT TORQUE OVERLOAD
382 T0C2 TRANSMISSION INPUT TORQUE OVERLOAD
383 T0C3 OVERTEMP CONVERTER OUTPUT
384 T0D1 S.C. TO BATTERY VOLTAGE AT POWER SUPPLY FOR SENSORS
385 T0D2 S.C. TO GROUND AT POWER SUPPLY FOR SENSORS
386 T0D3 LOW VOLTAGE AT BATTERY
387 T0D4 HIGH VOLTAGE AT BATTERY
388 T0D5 ERROR AT VALVE POWER SUPPLY VPS1
389 T0D6 ERROR VALVE POWER SUPPLY VPS2
390 T0D7 S.C. TO GROUND AT DHL LONGITUDINAL OUTPUT
391 T0D8 S.C. TO BATTERY VOLTAGE AT DHL LONGITUDINAL OUTPUT
392 T0D9 O.C. AT DHL LONGITUDINAL OUTPUT
393 T0E5 DISPID1_TIMEOUT
394 T0E6 ILLEGAL ID REQUEST VIA CAN
395 T0F1 GENERAL EEPROM FAULT
396 T0F2 CONFIGURATION LOST
397 T0F3 APPLICATION ERROR
398 T0F5 CLUTCH FAILURE
399 T0F6 CLUTCH ADJUSTMENT DATA LOST OR INCHPEDAL CALIBRATION DATA LOST
400 T0F7 SUBSTITUTE CLUTCH CONTROL
500 S000 1’s complement redundancy test
501 S001 1st boot
502 S002 Division by zero
503 S003 CapCom values
504 S004 Variable truncation
505 S005 Verified write to cell error
506 S006 Estimate Calibration values error
507 S007 PWM Calibration values error
508 S008 Mechanical Spool Compensation values
509 S009 CRC16 check / Parameter Memory
510 S010 Fall back to old values.
511 S011 CRC16 check / Program Memory
512 S012 LVDT wiring error
513 S013 Power supply above specified range
514 S014 Power supply below specified range
515 S015 No answer on handshakes
516 S016 Power-on self test failed
517 S017 Main spool cannot reach neutral
518 S018 Main spool cannot reach float position
519 S019 Main spool not in neutral at boot up
520 S020 Main spool position is greater than the reference
521 S021 Main spool position and reference are in opposite directions
522 S022 Float threshold has not been passed
523 S023 Time guarding on Auxiliary Valve Command
524 S024 Illegal CAN address
525 S025 Command out of range
526 S026 Scaling error
527 S027 Ramps error
528 S028 Float threshold error
529 S029 Dead band compensation error
530 S030 Slope error
531 S031 Shape error
532 S032 Invert port error
533 S033 Illegal combination of Port Flow Command and Blocked state
534 S034 Illegal combination of Port Flow Command and Float state
535 S035 Port Flow Command above 100%
536 S036 Illegal Valve State
537 S037 Illegal valve state and illegal Port Flow Command
538 S038 Illegal combination of inverted ports and float properties
FMI Comments
0 Above normal range
1 Below normal range
2 Incorrect signal
3 Voltage above normal
4 Voltage below normal
5 Current below normal
6 Current above normal
7 IMPROPER MECHANICAL RESPONSE(MECHANICAL SYSTEM NOT RESPOSDING OR OUT OF ADJUSTMENT)
8 Abnormal signal
9 Abnormal update
10 ABNORMAL RATE OF CHANGE(ABNORMAL RATE OF CHANGE)
11 Failure mode not identifiable
12 Failed
13 OUT OF CALIBRATION
14 SPECIAL INSTRUCTIONS
15 DATA VALID BUT BELOW NORMAL OPERATIONAL RANGE — LEAST SEVERSE LEVEL
16 DATA VALID BUT BELOW NORMAL OPERATIONAL RANGE — MODERATELY SEVERE LEVEL
17 DATA VALID BUT BELOW NORMAL OPERATIONAL RANGE — LEAST SEVERSE LEVEL
18 DATA VALID BUT BELOW NORMAL OPERATIONAL RANGE — MODERATELY SEVERE LEVEL
19 RECEIVED NETWORK DATA IN ERROR
20 RESERVED FOR SAE ASSIGNMENT
21 RESERVED FOR SAE ASSIGNMENT
22 RESERVED FOR SAE ASSIGNMENT
23 RESERVED FOR SAE ASSIGNMENT
24 RESERVED FOR SAE ASSIGNMENT
25 RESERVED FOR SAE ASSIGNMENT
26 RESERVED FOR SAE ASSIGNMENT
27 RESERVED FOR SAE ASSIGNMENT
28 RESERVED FOR SAE ASSIGNMENT
29 RESERVED FOR SAE ASSIGNMENT
30 RESERVED FOR SAE ASSIGNMENT
31 Not available or Condition exist
Doosan Fault Codes List.pdf
Adobe Acrobat Document
44.2 KB
HYDRAULIC SYSTEM
Problem Cause Remedy
All organs do not work. Failure of the hydraulic pump. Talk to
control (loud noise of pumps) to the distributor of the company
Doosan.
Not enough hydraulic Add
oils. hydraulic oil as required.
Suction line clogged or Clean or replace
damaged. if necessary.
All organs do not work Failure of the control pump Refer to
control (pump noise is not audible) of the circuit. distributor of the company
Doosan.
Cut-off failure Replace solenoid.
solenoid valve.
Safety end Adjust clearance
the switch is on. travel stop
Low power of all Insufficient hydraulic Add hydraulic
oil drives. oil as needed.
The vacuum filter is clogged. Clean filter.
Failure of hydraulic pumps. Contact your distributor
Doosan company.
Main unload pressure Contact distributor
oil flow is too low. Doosan company.
Hydraulic pumps Bleed air from
excavator. hydraulic pumps.
Power too low or Relief pressure Relieve pressure.
missing for only one or two functions. overload valve too small.
Fill leaks Clean or replace when
check valve. necessity.
Valve spool defective Replace valve spool.
distributor.
Dirt in the valve spool. Clear or replace when
necessity.
Drive failure. Repair or
replace if necessary.
Failure of the cylinder seal. Repair or
replace if necessary.
Cylinder rod damaged. Repair or
replace if necessary.
Remote valve failure Replace the control valve.
management.
Incorrect connection Connect correctly
control lines. control lines.
Oil temperature Defective oil cooler. Contact your distributor
too high. Doosan company.
Fan belt loose. Tighten fan belt
if necessary.
PLATFORM ROTATION SYSTEM
No swing Swing brake valve Replace the brake valve.
defective.
Failure of the hydraulics timer. Replace timer.
Low release pressure Adjust pressure.
brakes.
Swing motor failure. Replace swing motor.
Remote valve failure Replace the control valve.
management.
Incorrect connection Connect correctly
control lines. control lines.
The turn is jerky. Wear of the gearbox of the mechanism Replace the gearbox of the mechanism
turning. turning.
Bearing damaged Replace bearing.
swing mechanism.
Poor lubrication. Add grease.
ELECTRICAL SYSTEM
The battery does not hold Low battery power. Replace batteries.
charge. Alternator belt loose Tighten or replace
or damaged. belt.
Loose or Tighten or replace if
corroded findings. necessity.
Generator malfunction. Repair or
replace if necessary.
Low power Internal short circuit of the battery. Replace battery.
batteries. Short circuit wiring. Renovate.
Engine speed is not Adjustment disk failure Replace adjustment disk
regulated. engine speed. engine speed.
Throttle controller failure. Replace controller.
Speed control failure Repair or
engine. replace if necessary.
Blown fuse. Replace fuse.
Damaged wiring. Repair or
replace if necessary.
12 Indicates the end of one pass through the fault list.
14 ECT sensor input low usually appears if the coolant sensor wire is shorted to ground.
15 ECT sensor input high if the coolant sensor wire is disconnected or wire breakage.
16 ECT coolant temperature too high, measuring excessive temperature or shorted or sitting on ground.
22 Throttle sensor. Input signal wire Input Lo TPS1 is open
23 Throttle valve input sensor TPS1 shorted
24 Throttle sensor sensor TPS. Sensor malfunction
25 Throttle Body Temperature Sensor TPS Sensor Malfunction
26 ETC The ETC sensor supply wire is open or the throttle plate is sticking out inside the throttle body
27 Predicted difference TPS TPS 1 differs from the calculated position
28 ETC early test worked. Throttle spring return error
29 ETC Driver Fault Driver current throttle or driver signals shorted
33 Sensor low signal MAP wire in open circuit or chip open
34 High MAP signal shorted or sensor failure
37 IAT sensor input low, TMAP sensor failure or short circuit
38 IAT sensor input high, TMAP disabled or IAT signal open
42 EST 1. Coil driver low signal low or shorted to positive
43 EST 1. High excitation signal of the coil of high or high current
52 Low engine oil pressure
53 Battery charge sensor input, low battery voltage measured below 8.0 VDC
54 Battery sensor input high battery voltage measured above 15.9 VDC
55 XDRP sensor input sensor low level, below 4.6 VDC
56 Sensor input XDRP sensor high level, above 5.2 VDC
57 The increased engine speed has exceeded the maximum speed setpoint
61 Pedal sensor input 1 Lo APP1 signal disconnected, open circuit or sensor malfunction
62 Pedal sensor input 1 Hi APP1 sensor error or short circuit
63 Pedal sensor range 1 Lo potentiometer APP1
64 Pedal sensor range 1 Hi APP1 potentiometer not working
65 Pedal sensor sensor input Lo APP2 sensor error or short circuit
66 Pedal sensor input 2 Hi APP2 signal disconnected, open circuit or sensor malfunction
67 Pedal sensor range 2 Local malfunction of the potentiometer APP2
68 Pedal sensor range 2 Hi APP2 Potentiometer malfunction
69 Pedal 1. Pedal 2. The difference in the measured signal of the pedal position APP2 differs from APP1
71 AFR Trim Valve Output. FTV Modulation Driver Signal Error
72 Stop valve AFR lower duty cycle FTV at lower limit (LEAN)
73 AFR Trim Valve upper duty cycle DC FTV at the upper (RICH) limit
74 Switching O2 sensor sensor not switching over voltage reference AFR
77 Oxygen sensor input. O2 sensor high signal shorted to +5 VDC
Doosan / Daewoo DH130
Doosan / Daewoo DH170III
Doosan / Daewoo DH220LC
Doosan / Daewoo DH450
Doosan / Daewoo DX140LC
Doosan / Daewoo DX180LC
Doosan / Daewoo DX225LC
Doosan / Daewoo DX255LC
Doosan / Daewoo DX255LCA
Doosan / Daewoo DX300
Doosan / Daewoo DX300LC V
Doosan / Daewoo DX420LC V
Doosan / Daewoo SOLAR 130V
Doosan / Daewoo SOLAR 280LC III
Doosan / Daewoo SOLAR 290V
Doosan / Daewoo SOLAR 330III
Doosan / Daewoo SOLAR 75
Doosan DX140LCR
Doosan DX200A
Doosan DX220A
Doosan DX225LC SLR
Doosan DX225LCA
Doosan DX225NCL
Doosan DX225NLCA
Doosan DX235LCR
Doosan DX235NLC
Doosan DX255LC SLR
Doosan DX260LCA
Doosan DX300LC
Doosan DX300LC SLR
Doosan DX300LC-3
Doosan DX300LCA
Doosan DX340LC
Doosan DX340LC-3
Doosan DX340LCA
Doosan DX380LC
Doosan DX380LC-3
Doosan DX420LC
Doosan DX420LCA
Doosan DX480LC
Doosan DX480LCA-HD
Doosan DX500LCA / 520LCA-HD
Doosan DX520LC
Doosan DX520LC SLR
Doosan DX700LC
Doosan SOLAR 225LC-7
Doosan SOLAR 225NLC-V
Doosan SOLAR 300LC-7
Doosan SOLAR 340LC-V
Doosan SOLAR 500LC-V
An international corporation with a wide range of industries and a network of representative offices around the world. Since acquiring Daewoo Heavy Industries & Machinery in 2005, Doosan has also focused on the construction equipment market.
Then it all started with excavators and wheel loaders. Now the South Korean company Doosan ranks 8th in the world in the production of earthmoving and road construction equipment.
The company’s annual turnover is $ 11 billion. As a result of the transformation, Doosan is progressively pursuing a strategy to achieve leadership in its segment. In 2015, it was ranked 10th in
the world in the production of construction equipment, and in 2016 it climbed 2 levels higher and took 8th place. Doosan expects to become the world’s third largest manufacturer of construction
machinery and equipment after Caterpillar and Komatsu, with annual
sales of $ 12 billion.
The company’s products are excavators, consumer goods, real estate, financial services, IT services, media, retail, industrial equipment and consulting.
In 1977, Daewoo Heavy Industries was established as a division of the South Korean corporation Daewoo. Collaboration with Hitachi launched the production of crawler excavators, which led to the
in-house production of the Solar range after 8 years.
Doosan bought Daewoo Heavy Industries in 2005, which allowed it to strengthen its position in the construction equipment market. Since that time, all equipment began to come under the
Doosan-Daewoo brand. But in 2007, it was decided to promote the technique only under the Doosan brand.
It is worth noting that Doosan Corporation produces a wide range of products, from food and beverage products to engines, heavy equipment and power plants. The construction equipment is handled
by the Doosan Infacore division.
Doosan Infacore is a global corporation with a wide range of industries and a network of representative offices around the world. As noted, the company acquired Daewoo Heavy Industries &
Machinery in 2005, allowing Doosan to enter the construction machinery market. It all started with the release of Doosan excavators and front loaders. At the end of 2010, the South Korean company
ranked 6th in the world in the production of earthmoving and road construction equipment.