– Printer model: Kyocera KM1620
– Fix Error codes on Kyocera KM1620 model and its description:
- Code: C010
- Description: Backup memory read/write problem (main PCB)
• Read and write data does not match. - Causes: Defective backup RAM or main PCB.
- Remedy: Replace the main PCB and check for correct operation.
- Code: C011
- Description: Backup memory data problem (main PCB)
• Data in the specified area of the backup memory does not match the specified values. - Causes: Problem with the backup memory data. Defective backup RAM.
- Remedy: Turn safety switch off and back on and run maintenance item U020 to set the contents of the backup memory data again. If the C011 is displayed after re-setting the backup memory contents, replace the backup RAM or main PCB.
- Code: C015
- Description: Backup memory read/write problem (engine PCB)
• Read and write data does not match. - Causes: Defective backup RAM or engine PCB.
- Remedy: Replace the engine PCB and check for correct operation.
- Code: C016
- Description: Backup memory data problem (engine PCB)
• Data in the specified area of the backup memory does not match the specified values. - Causes: Problem with the backup memory data. Defective backup RAM.
- Remedy: Turn safety switch off and back on and run maintenance item U020 to set the contents of the backup memory data again. If the C016 is displayed after re-setting the backup memory contents, replace the backup RAM or engine PCB.
- Code: C017
- Description: Accounting count problem
• When the power is turned on, the total count and the scan count are abnormal both on the main PCB and the engine PCB. - Causes: Defective main PCB or engine PCB.
- Remedy: Replace the main PCB or engine PCB and check for correct operation.
- Code: C018
- Description: Machine number mismatch
• When the power is turned on, the machine number does not match between the main PCB and the engine PCB. - Causes: Correct EEPROM is not installed. Data damage of EEPROM.
- Remedy: Install the correct EEPROM. If it does not solve the problem, contact the Service Administrative Division. Contact the Service Administrative Division.
- Code: C021
- Description: Communication problem between the main PCB and engine board PCB
• When the power is turned on, the machine does not detect the low level of SBSY and the high level of SDIR for three seconds. - Causes: Poor contact in the connector terminals. Defective main PCB or engine PCB.
- Remedy: Check the connection of connectors YC6 on the main PCB and YC1 on the engine PCB, and the continuity across the connector terminals. Repair or replace if necessary. Replace the main PCB or engine PCB and check for correct operation.
- Code: C041
- Description: Optional DP communication problem
• Communication fails five times successively. - Causes: DP installed incorrectly. Defective main PCB or DP driver PCB.
- Remedy: Check the installation state of the DP and adjust it if it is not properly installed. Replace the main PCB or DP driver PCB and check for correct operation.
- Code: C042
- Description: Optional first paper feeder communication problem
• Communication fails five times successively. - Causes: Paper feeder installed incorrectly. Defective main PCB or drawer main PCB.
- Remedy: Check the installation state of the paper feeder and adjust it if it is not properly installed. Replace the main PCB or drawer main PCB and check for correct operation.
- Code: C050
- Description: Optional second paper feeder communication problem
• Communication fails five times successively. - Causes: Paper feeder installed incorrectly. Defective main PCB or drawer main PCB.
- Remedy: Check the installation state of the paper feeder and adjust it if it is not properly installed. Replace the main PCB or drawer main PCB and check for correct operation.
- Code: C051
- Description: Optional third paper feeder communication problem
• Communication fails five times successively. - Causes: Paper feeder installed incorrectly. Defective main PCB or drawer main PCB.
- Remedy: Check the installation state of the paper feeder and adjust it if it is not properly installed. Replace the main PCB or drawer main PCB and check for correct operation.
- Code: C061
- Description: Bitmap (DIMM) problem
• There is a problem with the data or address bus of the bitmap DRAM. - Causes: Defective main PCB. DIMM installed incorrectly. Defective DIMM.
- Remedy: Replace the main PCB and check for correct operation. Check if the DIMM is inserted into the socket on the main PCB correctly. Replace the DIMM and check for correct operation.
- Code: C062
- Description: Memory input interface problem
• Reading-in of an image does not complete within 10 s of the start of image transmission. - Causes: Defective main PCB.
- Remedy: Replace the main PCB and check for correct operation.
- Code: C063
- Description: DMA problem
• DMA transmission of compressed, decompressed, rotated, relocated or blanked-out image data does not complete within the specified period of time. - Causes: Defective main PCB.
- Remedy: Replace the main PCB and check for correct operation.
- Code: C080
- Description: Image processing problem
• JAM05 is detected twice. - Causes: Defective engine PCB.
- Remedy: Replace the engine PCB and check for correct operation.
- Code: C200
- Description: Drive motor problem
• LOCK ALM signal remains high for 1 s, 1 s after the drive motor has turned on. - Causes: Poor contact in the main motor connector terminals. Defective drive motor rotation control circuit. Defective drive transmission system.
- Remedy: Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the drive motor. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
- Code: C310
- Description: Scanner carriage problem
• The home position is not correct when the power is turned on or copying the document placed on the contact glass. - Causes: Poor contact of the connector terminals. Defective scanner home position switch. Defective engine PCB. Defective scanner motor.
- Remedy: Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the scanner home position switch. Replace the engine PCB and check for correct operation. Replace the scanner motor.
- Code: C320
- Description: Exposure lamp problem
• In indicator check before starting copying, the average value in scanning of the shading plate with the CCD is 128 or more. - Causes: Poor contact of the connector terminals. Defective exposure lamp or inverter board. Defective engine PCB. Incorrect shading position.
- Remedy: Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the exposure lamp or inverter board. Replace the engine PCB and check for correct operation. Adjust the position of the contact glass (shading plate). If the problem still occurs, replace the scanner home position switch.
- Code: C330
- Description: Optical system (AGC) problem
• After AGC, correct input is not obtained at CCD. - Causes: Insufficient exposure lamp luminosity. Defective engine PCB. Incorrect shading position.
- Remedy: Replace the exposure lamp or inverter board. Replace the engine PCB and check for correct operation. Adjust the position of the contact glass (shading plate). If the problem still occurs, replace the scanner home position switch.
- Code: C400
- Description: Polygon motor synchronization problem
• The polygon motor does not reach the stable speed within 15 s of the START signal turning on. - Causes: Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective engine PCB.
- Remedy: Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the LSU. Replace the engine PCB and check for correct operation.
- Code: C401
- Description: Polygon motor steady-state problem
• The polygon motor rotation is not stable for 5 s after the polygon motor rotation has been stabilized. - Causes: Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective engine PCB.
- Remedy: Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the LSU. Replace the engine PCB and check for correct operation.
- Code: C420
- Description: BD steady-state problem
• The MIC detects a BD error for 600ms after the polygon motor rotation has been stabilized. - Causes: Defective laser diode. Defective polygon motor. Defective main PCB. Defective engine PCB.
- Remedy: Replace the LSU. Replace the LSU. Replace the main PCB and check for correct operation. Replace the engine PCB and check for correct operation.
- Code: C600
- Description: Broken fixing heater wire
• In fixing warm-up, the time to reach 50°C/122 °F exceeds 13.5 s, the time to reach 100°C/212 °F exceeds 10 s, the time to reach the primary stabilization exceeds 10 s or the time to reach the secondary stabilization exceeds 24 s. - Causes: Poor contact in the thermistor connector terminals. Fixing thermistor installed incorrectly. Fixing thermostat triggered. Fixing heater M or S installed incorrectly. Broken fixing heater M or S wire.
- Remedy: Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check and reinstall if necessary. Check for continuity. If none, replace the fixing thermostat. Check and reinstall if necessary. Check for continuity. If none, replace the heater lamp.
- Code: C602
- Description: Abnormally high fixing unit thermistor temperature
• The fixing temperature exceeds 230°C/446 °F for 40 ms. - Causes: Shorted thermistor. Broken heater control circuit on the power supply PCB.
- Remedy: Measure the resistance. If it is 0 Ω, replace the thermistor. Replace the power supply PCB and check for correct operation.
– Kyocera KM1620 printer Error Codes and quick guide to troubleshooting:
- Code: C605
- Description: Abnormally low fixing unit thermistor temperature
• The fixing temperature remains below 90°C/194°F for 1 s. - Causes: Poor contact in the thermistor connector terminals. Broken fixing thermistor wire. Fixing thermistor installed incorrectly. Fixing thermostat triggered. Fixing heater M or S installed incorrectly. Broken fixing heater M or S wire.
- Remedy: Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Measure the resistance. If it is ∞Ω, replace the fixing thermistor. Check and reinstall if necessary. Check for continuity. If none, replace the fixing thermostat. Check and reinstall if necessary. Check for continuity. If none, replace the fixing heater M or S.
- Code: C640
- Description: Zero-crossing signal problem
• The engine PCB does not detect the zero-crossing signal for the time specified below. At power-on: 3 s Others: 5 s - Causes: Poor contact in the connector terminals. Defective power supply PCB. Defective engine PCB.
- Remedy: Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if the zero-crossing signal is output from CN2-5 on the power supply PCB. If not, replace the power supply PCB. Replace the engine PCB if C640 is detected while CN2-5 on the power supply PCB outputs the zero-crossing signal.
- Code: C780
- Description: Broken external temperature thermistor
• The input voltage is 0.5 V or less. - Causes: Poor contact in the humidity sensor connector terminals. Defective humidity sensor.
- Remedy: Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the drawer PCB and check for correct operation.
- Code: C781
- Description: Short-circuited external temperature thermistor
• The input voltage is 4.5 V or more. - Causes: Defective humidity sensor. Poor contact in the humidity sensor connector terminals. Defective humidity sensor.
- Remedy: Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the drawer PCB and check for correct operation.
– Buy WIC Reset key on my online store: https://shop.nguyendangnam.com/product/epson-px-730wd-wic-reset-utility-tool/
– Free Download Epson in specific model: https://dnasofts.com/download-epson-lq-1170+-driver-firmware-and-manuals/
Source:
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html
Contact us to get support with Kyocera KM1620 Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
Code
C0420
(A0420*)
C0500
(A0500*)
C0510
(A0510*)
C0610
(A0610*)
C0620
(A0620*)
C0630
(A0630*)
C0800
(A0800*)
C2000
«A» is displayed on the operation panel.
Downloaded from
www.coronatechnical.com
Contents
Optional first paper feeder communi-
cation problem
• Communication fails five times suc-
cessively.
Optional second paper feeder com-
munication problem
• Communication fails five times suc-
cessively.
Optional third paper feeder commu-
nication problem
• Communication fails five times suc-
cessively.
Bitmap (DIMM) problem
• There is a problem with the data or
address bus of the bitmap DRAM.
Memory input interface problem
• Reading-in of an image does not
complete within 10 s of the start of
image transmission.
DMA problem
• DMA transmission of compressed,
decompressed, rotated, relocated or
blanked-out image data does not
complete within the specified period
of time.
Image processing problem
• JAM05 is detected twice.
Drive motor problem
• LOCK ALM signal remains high for 1
s, 1 s after the drive motor has turned
on.
manuals search
Remarks
Causes
Check procedures/corrective measures
Paper feeder in-
Check the installation state of the paper
stalled incorrectly.
feeder and adjust it if it is not properly in-
stalled.
Defective main
Replace the main PCB or drawer main
PCB or drawer
PCB and check for correct operation.
main PCB.
Paper feeder in-
Check the installation state of the paper
stalled incorrectly.
feeder and adjust it if it is not properly in-
stalled.
Defective main
Replace the main PCB or drawer main
PCB or drawer
PCB and check for correct operation.
main PCB.
Paper feeder in-
Check the installation state of the paper
stalled incorrectly.
feeder and adjust it if it is not properly in-
stalled.
Defective main
Replace the main PCB or drawer main
PCB or drawer
PCB and check for correct operation.
main PCB.
Defective main
Replace the main PCB and check for cor-
PCB.
rect operation.
DIMM installed
Check if the DIMM is inserted into the
incorrectly.
socket on the main PCB correctly.
Defective DIMM.
Replace the DIMM and check for correct
operation.
Defective main
Replace the main PCB and check for cor-
PCB.
rect operation.
Defective main
Replace the main PCB and check for cor-
PCB.
rect operation.
Defective engine
Replace the engine PCB and check for
PCB.
correct operation.
Poor contact in
Reinsert the connector. Also check for con-
the main motor
tinuity within the connector cable. If none,
connector termi-
remedy or replace the cable.
nals.
Defective drive
Replace the drive motor.
motor rotation
control circuit.
Defective drive
Check if the rollers and gears rotate
transmission sys-
smoothly. If not, grease the bushings and
tem.
gears. Check for broken gears and replace
if any.
Kyocera-Mita
Сводная таблица ошибок монохромных копиров Kyocera (Kyocera-Mita) серии KM
- Все ошибки даны в четырехзначной кодировке. Аппараты раннего выпуска выдают трехзначные коды ошибок; в этом случае четвертый знак всегда ноль. Например, если аппарат выдает ошибку вида «C123», то в таблице следует смотреть ошибку номер 1230.
- В начале идут общие ошибки для всей серии, затем ошибки, специфичные для конкретных аппаратов. Ошибки финишеров (8000…8999) идут в конце таблицы.
- Таблица составлена для аппаратов: KM-1500 / 1505 / 1510 / 1810 / 1525 / 1530 / 2030 / 1620 / 2020 / 1635 / 2035 / 1650 / 2050 / 2550 / 2530 / 3530 / 3035 / 4035 / 5035 / 4230 / 5230 / 6230 / 4530 / 5530 / 6330 / 7530 / 6030 / 8030, FS-1018 / 1118 (KM-1820).
Соответствие кодов ошибок для аппаратов, не перечисленных в этом списке, не гарантируется. - Ошибки термоблока (6000…6999) блокируют работу аппарата. После проверки работоспособности и безопасности работы их следует сбросить в сервисном режиме U163.
- Некоторые ошибки дополнительных устройств разрешают дальнейшую работу копира, но блокируют работу дополнительного устройства. Сброс ошибки производится в сервисном режиме U906.
- Ошибки, не перечисленные выше, сбрасываются при выключении питания.
Общие ошибки
| Код ошибки | Описание |
|---|---|
| 0030 | Fax control PWB system problem |
| 0070 | Fax control PWB incompatibility detection problem |
| 0100 | Backup memory read/write problem (main board) |
| 0110 | Backup memory data problem (main board) |
| 0120 | Drum EEPROM read/write problem (для 2550) |
| 0130 | Backup memory read/write problem (main PCB EEPROM) (для 1650/2050/2550) |
| 0140 | Backup memory data problem (main PCB EEPROM) (для 1650/2050/2550) |
| 0150 | Backup memory read/write problem (engine board) |
| 0160 | Backup memory data problem (engine board) |
| 0170 | Accounting count problem |
| 0180 | Machine number mismatch |
| 0210 | Communication problem between the main board and engine board (для KM-1500/1620/2020/1635/2035/1650/2050/2550/6030/8030, FS-1018/1118) |
| Communication problem between the main board and operation board (для KM-1525/1530/2030/2530/3530/6230/4530/5530/6330/7530) | |
| 0240 | Printer board PWB communication problem |
| 0250 | Scanner network board communication problem |
| 0280 | Communication problem between the fax control PWB and main PWB |
| 0320 | Side deck communication problem |
| 0340 | Finisher communication problem |
| 0410 | Optional DP communication problem |
| 0420 | Optional first paper feeder communication problem |
| Large paper deck /paper feed desk communication problem /Side deck communication problem | |
| 0440 | Finisher communication problem |
| 0450 | Mailbox communication problem |
| 0470 | Switchback unit communication problem |
| 0500 | Optional second paper feeder communication problem |
| 0510 | Optional third paper feeder communication problem |
| 0600 | DIMM problem (для 2530/3530) |
| 0610 | Bitmap (DIMM) problem |
| 0620 | Memory input interface problem |
| 0630 | DMA problem |
| 0640 | Hard disk drive problem |
| 0800 | Image processing problem (JAM05 is detected twice) |
| 0820 | Fax control PCB CG ROM checksum error |
| 0830 | Flash ROM program area checksum error |
| 0860 | Fax control PCB software switch checksum error |
| 0870 | Fax control PWB to main PWB high capacity data transfer problem |
| 0880 | Fax control PWB program archive problem |
| 0890 | Fax control PCB CG font archive problem |
| 0900 | Fax software incompatibility detection problem |
| 0920 | Fax file system error |
| 0960 | Developer EEPROM read/write problem (для 2550/6030/8030) |
| 1000 | Exposure lamp problem |
| 1010 | Lift motor 1 error |
| 1020 | Lift motor 2 error |
| 1030 | Lift motor 3 error |
| 1040 | Lift motor 4 error |
| 1100 | Paper deck motor 1 problem [Drawer 3] |
| 1110 | Paper deck motor 2 problem [Drawer 4] |
| 1120 | Deck right lift position problem |
| 1130 | Deck left lift position problem |
| 1140 | Side deck lift motor (going up) problem |
| 1150 | Side deck lift motor (going down) problem |
| 1160 | Large paper deck (paper feed desk) sequence problem |
| 1170 | Large paper deck (paper feed desk) incorrect type problem |
| 2000 | Main motor problem |
| Image forming motor problem (для 6230/4530/5530/6330/7530) | |
| 2500 | Paper feed motor problem |
| 2550 | Paper conveying motor problem (для 4530/5530) |
| 2600 | Deck conveying motor /desk drive motor problem |
| 2640 | Side deck drive motor problem |
| 3100 | Scanner carriage problem |
| 3200 | Exposure lamp problem |
| 3300 | Optical system (AGC) problem |
| 4000 | Polygon motor synchronization problem |
| 4010 | Polygon motor steady-state problem |
| 4100 | BD initialization (A) problem |
| 4110 | BD initialization (B) problem |
| 4200 | BD steady-state problem |
| 5100 | Main charger problem |
| 5110 | Transfer/separation high voltage problem |
| 5300 | Broken cleaning lamp wire |
| 5500 | Drum surface potential sensor problem 1 |
| 5510 | Drum surface potential sensor problem 2 |
| 5600 | Drum surface potential problem 1 |
| 5610 | Drum surface potential problem 2 |
| 6000 | Broken fixing heater wire |
| 6020 | Abnormally high fixing unit thermistor temperature |
| 6030 | Broken fixing unit thermistor |
| 6050 | Abnormally low fixing unit thermistor temperature |
| 6100 | Broken fixing heater wire |
| 6200 | Abnormally low fixing unit thermistor temperature |
| 6300 | Abnormally high fixing unit thermistor temperature |
| 6400 | Zero-crossing signal problem |
| 6410 | Fixing unit connector insertion problem |
| 6420 | Fixing fuse cut problem |
| 6420 | Broken fixing unit thermistor wire |
| 7100 | Toner sensor problem |
| 7300 | Broken external temperature thermistor wire (для KM-1505/1510/1810/4230/5230/6230) |
| Toner sensor problem/ Toner hopper problem (для KM-2530/3530/3035/4035/5035/6230/4530/5530/6330/7530/6030/8030) | |
| 7310 | Short-circuited external temperature thermistor |
| 7400 | Image formation unit connector insertion problem |
| Developing unit connector insertion problem (для 2550) | |
| 7410 | Drum unit connector insertion problem |
| 7750 | Drum type mismatch problem A (для 1635/2035) |
| 7760 | Drum type mismatch problem B (для 1635/2035) |
| 7800 | Broken external temperature thermistor |
| 7810 | Short-circuited external temperature thermistor |
KM-1500, FS-1018/1118 (KM-1820)
| Код ошибки | Описание |
|---|---|
| 0220 | Communication problem between the main board and operation board (для 1018/1118) |
| F— | Controller system error (для 1018/1118) |
| F010 | ROM checksum error (для 1118) |
| F012 | |
| 7980 | Waste toner reservoir overflow problem (when the total number of copies is less than 100 thousand sheets) |
| 7990 | Waste toner reservoir overflow problem (when the total number of copies is 100 thousand sheets or more) |
KM-1505/1510/1810/1525/1530/2030
| Код ошибки | Описание |
|---|---|
| 0210 | Printer board communication problem (для 1505/1510/1810) |
| 0400 | DIMM problem |
| 0410 | Bitmap problem |
| 0430 | DMA problem |
| 1040 | Optical system problem (AGC) |
Kyocera-Mita 3035/4035/5035
| Код ошибки | Описание |
|---|---|
| 0100 | Operation unit PCB backup memory read/write error |
| 0110 | Operation unit PCB backup memory data problem |
| 0210 | MMI communication problem |
| 0320 | Energy save communication problem |
| 7450 | Image formation unit fuse cut problem |
Kyocera Mita 4230/5230
| Код ошибки | Описание |
|---|---|
| 0010 | Memory copy PCB 1 communication problem |
| 0030 | Memory copy PCB 2 communication problem |
| 0100 | RAM/ROM problem |
| 0220 | Communication problem between the engine PCB and main PCB |
| 0230 | Scanner communication problem |
| 0260 | Memory copy PCB 1 communication problem |
| 0320 | Large paper deck communication problem /Paper feed desk communication problem |
| 0360 | Memory copy PCB 2 communication problem |
| 0370 | Communication microcomputer problem |
| 1040 | Optical system problem (AGC) |
| 2100 | Paper conveying motor problem |
| 2200 | Side registration motor problem |
| 2300 | Paper feed motor problem |
| 2310 | Desk drive motor problem |
| 2410 | Upper lift motor problem |
| 2420 | Lower lift motor problem |
| 2430 | Upper desk lift motor problem |
| 2440 | Lower desk lift motor problem |
| 3320 | Scanner watchdog problem |
| 3400 | Original detection position problem |
| 7400 | Toner hopper problem |
| 9200 | Deck paper conveying motor problem |
| 9210 | Paper deck motor 1 problem |
| 9220 | Paper deck motor 2 problem |
| 9230 | Right lift position problem |
| 9240 | Left lift position problem |
Kyocera-Mita 6030/8030
| Код ошибки | Описание |
|---|---|
| 0060 | Main PWB type mismatch error |
| 0130 | Backup memory (EEPROM) device problem |
| 0140 | Backup memory (EEPROM) data problem |
| 0220 | Scanner communication problem |
| 0330 | Relay board communication problem |
| 0460 | Duplex unit communication problem |
| 0470 | Sheet inserter communication problem (optional document finisher) |
| 0500 | Paper feed unit communication error (cassette 1 and 2) |
| 0510 | Paper feed unit communication error (cassette 3 and 4) |
| 0700 | Side feeder EEPROM error (optional side feeder) |
| 0750 | Document finisher EEPROM error |
| 0970 | Cleaning unit EEPROM error |
| 1200 | Duplex side registration motor error |
| 2100 | Developing motor error |
| 2200 | Drive motor error |
| 2300 | Fuser motor error |
| 2550 | Transfer motor error |
| 3210 | CIS lamp problem |
| 3310 | Optical system (AGC) problem (DP) |
| 3500 | Communication error between scanner and SHD |
| 3900 | Backup memory read/write error (scanner PWB) |
| 3910 | |
| 4120 | BD initialization (C) problem |
| 7200 | Broken drum thermistor wire |
| 7210 | Shorted drum thermistor |
| 9040 | DP lift motor going up error |
| 9050 | DP lift motor going down error |
| 9060 | DP EEPROM error |
| 9070 | Communication problem between DP and SHD |
| 9080 | Communication problem between DP and CIS |
Kyocera Mita 6230
| Код ошибки | Описание |
|---|---|
| 0010 | Memory PCB communication problem |
| 0100 | RAM/ROM problem |
| 0260 | Memory copy PCB 1 communication problem |
| 0350 | Mailbox communication problem |
| 0370 | Communication microcomputer problem |
| 0380 | Hard disk problem |
| 0390 | DIMM problem |
| 1040 | Optical system problem (AGC) |
| 2100 | Drive motor problem / Paper conveying motor problem |
| 2200 | Paper feed motor problem |
| 2300 | Large paper deck right lift motor problem |
| 2310 | Large paper deck left lift motor problem |
| 2420 | Upper lift motor problem |
| 2430 | Lower lift motor problem |
| 6500 | Broken fixing unit thermistor wire |
| 7200 | Broken drum thermistor wire |
| 7210 | Shorted drum thermistor |
| 7220 | Broken drum heater wire |
KyoceraMita 6330/7530
| Код ошибки | Описание |
|---|---|
| 1060 | Large paper deck left lift motor problem |
| 2550 | Drive motor problem |
| 7520 | Shorted drum thermistor |
| 7530 | Broken drum thermistor wire |
Ошибки финишеров
| Код ошибки | Описание |
|---|---|
| 8010 | Finisher paper conveying motor problem |
| 8030 | Finisher (upper) paper conveying belt problem |
| 8140 | Finisher tray elevation motor problem /Main tray problem |
| 8170 | Finisher front side registration motor problem |
| 8180 | Finisher rear side registration motor problem |
| Finisher rear jogger motor problem (для 4230/5230) | |
| 8190 | Finisher trailing edge registration motor problem |
| 8210 | Finisher stapler motor problem |
| 8220 | Finisher rear stapler problem |
| 8300 | Document finisher centerfold unit communication problem |
| 8310 | Document finisher centerfold unit side registration guide problem |
| 8320 | Document finisher centerfold unit centering plate problem |
| 8330 | Document finisher centerfold blade problem |
Ошибки финишеров KM-2530/3530/3035/4035/5035
| Код ошибки | Описание |
|---|---|
| 8300 | Booklet stitcher paper ejection motor problem |
| 8310 | Booklet stitcher elevation motor problem |
| 8320 | Booklet stitcher rear jog motor problem |
| 8330 | Booklet stitcher front jog motor problem |
| 8340 | Booklet stitcher staple motor problem |
| 8350 | Booklet stitcher batch processing motor problem |
| 8360 | Booklet stitcher stapler shift motor problem |
| 8370 | Booklet stitcher paddle motor problem |
| 8380 | Booklet stitcher folding problem |
| 8390 | Booklet stitcher backup RAM data problem |
| 8400 | Booklet stitcher incorrect type problem |
| 8410 | Booklet stitcher punch motor problem |
| 8420 | Booklet stitcher shift motor problem |
| 8430 | Booklet stitcher punch communication problem |
| 8440 | Booklet stitcher punch sensor problem |
| 8450 | Booklet stitcher side punch sensor problem |
| 8460 | Booklet stitcher punch backup RAM data problem |
| 8470 | Booklet stitcher punch dust sensor problem |
| 8480 | Booklet stitcher broken punch power source wire problem |
| 8500 | Mailbox drive motor problem |
Ошибки финишера KM-6230
| Код ошибки | Описание |
|---|---|
| 8180 | Finisher rear jogger motor problem |
| 8310 | Booklet stitcher paper ejection motor problem |
| 8320 | Booklet stitcher elevation motor problem |
| 8330 | Booklet stitcher jog motor problem |
| 8340 | Booklet stitcher staple motor problem |
| 8350 | Booklet stitcher stapler unit shift motor problem |
| 8360 | Booklet stitcher stack level detection sensor problem |
| 8370 | Booklet stitcher punch motor problem |
| 8380 | Booklet stitcher punch shift motor problem |
| 8390 | Booklet stitcher swing motor problem |
| 8400 | Booklet stitcher backup RAM data problem |
| 8410 | Booklet stitcher punch unit backup RAM data problem |
| 8420 | Booklet stitcher positioning plate motor problem |
| 8430 | Booklet stitcher folding motor problem |
| 8440 | Booklet stitcher guide motor problem |
| 8450 | Booklet stitcher jog motor problem |
| 8460 | Booklet stitcher rear staple motor problem |
| 8470 | Booklet stitcher front staple motor problem |
| 8480 | Booklet stitcher thrust motor problem |
| 8490 | Booklet stitcher communication error |
Ошибки финишеров KM-6330/7530/6030/8030
| Код ошибки | Описание |
|---|---|
| 8000 | Document finisher incorrect type problem (для 6330/7530) |
| 8020 | Finisher punch motor problem |
| 8040 | Finisher lower paper conveying belt problem |
| 8150 | Finisher multi job tray problem |
| 8170 | Front upper side-registration guide problem |
| 8180 | Finisher rear upper side-registration guide problem |
| 8190 | Finisher lower side-registration guide problem |
| 8220 | Finisher front clincher problem |
| 8230 | Finisher rear stapler problem |
| 8240 | Finisher rear clincher problem |