Модераторы: KOT, Женька 116
Добрый вечер!
Принесли принтер с ошибкой их даже 2, 0х61011be5 и 0x610000f6
Включается без проблем но вовремя самодиагностики выдает ошибку 0х61011be5, если нажать ОК (как всегда пишет вкл./выкл. принтер)
просмотрел парковку все в норме, посторонних предметов нет, иногда вслючается без ошибки 0х61011be5 и можно по менюшке полазить, но как ставишь на печать любой документ, выпадает ошибка 0x610000f6.
в чем косяк может быть ?
з.ы. склоняюсь к плате управления, что пришел ее час.
-
galavarez
- Собрал картридж
-
- Сайт
- ICQ
- Персональный альбом
Вернуться в Принтеры струйные
Кто сейчас на форуме
Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 18
Hello.
Thank you that responded.
Made that procedure that you described, unfortunately it didn’t help.
And to make as it is described, it didn’t turn out as it is possible to catch the carriage with cartridges (that to derive them) only having disconnected the printer from a network at the moment when the carriage is in a zone of a drostup (that I also made). Did a procedure for the description further, only set cartridges too also as well as derived, that is caught the carriage when it was in an access zone, having disconnected the printer from a network. The printer recognized cartridges, they are recently bought, but the display gives the same error message 0x61011be5.
Rang in service center of HP, but roofing felts didn’t understand me there, roofing felts I didn’t understand them, they told that they don’t repair this model of the printer any more, already later I thought that they so answered, probably without having understood me, thought that I wanted to repair probably the printer on a warranty, but today found a workshop which agrees to repair the printer, on Thursday I will go. But wanted to hear your council. To carry to me it to repair, or still it is possible to try to make something?
This model of the printer is expensive to me, to printing quality there were no claims, and the most important Photosmart C5383 supports the printing on CD/DVD disks.
How to fix error code 0x61011be5 or ox61011be5 on HP printers
General Printer Error 0x61011be5.
Appears on these printers: D7560, C309A, C5390, C6380, …
Genraly it’s a carriage jam or a printhead issue.
Solution 1: Do a reset of the printer to factory default settings
- Verify that the unit is switched on.
- Disconnect the power cable from All-in-One and also from wall outlet.
- Wait a minute.
- Plug in the power cable to the printer and also to wall outlet.
- Unplug the power cable from the printer (with the printer powered on) and wait for 20 seconds.
- Then, press and hold «#» and «6» while plugging in the power cord.
- Release the buttons after connect power cord.
Solution 2:
- Open the printer and wait for the carriage to slide over
- Remove the ink cartridges from the print head.
- With a cotton swabs dipped in hot water, clean gently the print head and each ink cartridge, until there is no ink residue coming off on the cotton swab.
- Once all is dry, replace the cartridges
- Do a print test.
- If the error is still here: there are two possibilities:
- One of the ink cartridges is defective and causing the error
The print head will need to be replaced. (CN642A)
Popular posts from this blog
MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective…. but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON. When the printhead still moving and is going to the very LEFT, close the cover. Wait until its boot up. Solution 4a: Take out all of the ink cartridges Lift up the gr
The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr
MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on «Main», wait a few minutes. If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears «New device» Open the service tool
Photosmart D5463 Ошибка
Общая ошибка принтера 0х61011be5
| Сообщение #1
Отправлено 28 августа 2014 — 07:55
После ручной разблокировки печатающей головки принтер высветил «Общая ошибка принтера 0х61011be5». Что делать? Может кто сталкивался, помогите.
- Наверх of the page up there ^
-
0
| Сообщение #2
Отправлено 28 августа 2014 — 12:23
palacom
Принтер не подключен к компу через USB кабель. Может в этом дело?
- Наверх of the page up there ^
-
0
| Сообщение #3
Отправлено 28 августа 2014 — 19:44
sairon2
Нет. не в этом. Как вы разблокировали ПГ?
Всем удачи и побольше прибыльной работы!)))
- Наверх of the page up there ^
-
0
| Сообщение #4
Отправлено 29 августа 2014 — 04:11
palacom
- Наверх of the page up there ^
-
0
| Сообщение #5
Отправлено 29 августа 2014 — 05:25
palacom
- Наверх of the page up there ^
-
1
| Сообщение #6
Отправлено 01 сентября 2014 — 14:20
sairon2
Как себя ведет принтер? Сразу выдает ошибку? Или пытается механику запустить? Неправильно Вы разблокировали ПГ. Там все гораздо проще. Но это уже не важно.
Всем удачи и побольше прибыльной работы!)))
- Наверх of the page up there ^
-
0
| Сообщение #7
Отправлено 02 сентября 2014 — 04:49
palacom
При включении на экране после приветствия на синем фоне возникает надпись черным по белому — типа неверное выключение принтера, нажмите ОК. Затем он шоркает головку туда-сюда, прокачивает картриджи заводит головку на парковку и выдает сообщение об ошибке. Все это происходит как при закрытой так и при открытой крышке. Хотя головка при открытой крышке должна выйти на смену картриджей.
sairon2 сказал:
Неправильно Вы разблокировали ПГ
А как надо было? (Просто в сервисе отказались — неремонтопригоден)
- Наверх of the page up there ^
-
0
| Сообщение #8
Отправлено 05 сентября 2014 — 07:45
sairon2
Если честно то да. Очень капризный принтер. И очень тяжело ремонтировать. Для начала разберите принтер и снимите место парковки. Аккуратно разберите механизм парковки. Имхо Вы пошурудили отверткой там-где этого делать не стоило. И шланги посмотрите внимательно от места парковки до выхода к памперсу(он должен стоять под местом парковки.
Всем удачи и побольше прибыльной работы!)))
- Наверх of the page up there ^
-
0
| Сообщение #9
Отправлено 05 сентября 2014 — 10:18
palacom
sairon2 сказал:
Если он такой капризный, ни сделаю ли я хуже при такой полной разборке?
sairon2 сказал:
шланги посмотрите внимательно от места парковки до выхода к памперсу
Там идет три трубки — две белых и черная. Но я ведь их не трогал.
- Наверх of the page up there ^
-
0
| Сообщение #10
Отправлено 08 сентября 2014 — 18:20
sairon2
Может быть замятие. может клинить. Может и сделаете хуже-если не имеете технических навыков. Но мы же здесь обсуждаем тему не для того, чтоб я сказал-несите в сервис? В любом случае искать надо там.
Всем удачи и побольше прибыльной работы!)))
- Наверх of the page up there ^
-
0
- ← Предыдущая тема
- Hewlett Packard
- Следующая тема →
- Вы не можете создать новую тему
- Вы не можете ответить в тему
1 человек читают эту тему
0 пользователей, 1 гостей, 0 скрытых пользователей
Модераторы: KOT, Женька 116
Добрый вечер!
Принесли принтер с ошибкой их даже 2, 0х61011be5 и 0x610000f6
Включается без проблем но вовремя самодиагностики выдает ошибку 0х61011be5, если нажать ОК (как всегда пишет вкл./выкл. принтер)
просмотрел парковку все в норме, посторонних предметов нет, иногда вслючается без ошибки 0х61011be5 и можно по менюшке полазить, но как ставишь на печать любой документ, выпадает ошибка 0x610000f6.
в чем косяк может быть ?
з.ы. склоняюсь к плате управления, что пришел ее час.
-
galavarez
- Собрал картридж
-
- Сайт
- ICQ
- Персональный альбом
Вернуться в Принтеры струйные
Кто сейчас на форуме
Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 21
How to fix error code 0x61011be5 or ox61011be5 on HP printers
General Printer Error 0x61011be5.
Appears on these printers: D7560, C309A, C5390, C6380, …
Genraly it’s a carriage jam or a printhead issue.
Solution 1: Do a reset of the printer to factory default settings
- Verify that the unit is switched on.
- Disconnect the power cable from All-in-One and also from wall outlet.
- Wait a minute.
- Plug in the power cable to the printer and also to wall outlet.
- Unplug the power cable from the printer (with the printer powered on) and wait for 20 seconds.
- Then, press and hold «#» and «6» while plugging in the power cord.
- Release the buttons after connect power cord.
Solution 2:
- Open the printer and wait for the carriage to slide over
- Remove the ink cartridges from the print head.
- With a cotton swabs dipped in hot water, clean gently the print head and each ink cartridge, until there is no ink residue coming off on the cotton swab.
- Once all is dry, replace the cartridges
- Do a print test.
- If the error is still here: there are two possibilities:
- One of the ink cartridges is defective and causing the error
The print head will need to be replaced. (CN642A)
Popular posts from this blog
The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr
MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective…. but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON. When the printhead still moving and is going to the very LEFT, close the cover. Wait until its boot up. Solution 4a: Take out all of the ink cartridges Lift up the gr
MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on «Main», wait a few minutes. If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears «New device» Open the service tool
Ремонт HP C309h
Ошибка 0x61011beb HP C309h
В ремонт принесли МФУ HP PhotoSmart Premium C309h, который при подготовке к печати выдавал ошибку 0x61011beb.
Диагностика
После разборки принтера обнаружено отсутствие маятникового редуктора в узле обслуживания на валу, отвечающем за движение узла очистки.
Он валялся внизу. После замены шестерни была произведена установка маятника на место.
Маятниковый редуктор просто так не слетает. Поэтому мы произвели полную чистку узла обслуживания со снятием узла. После чистки и сборки ошибка исчезла.
Т.о. ошибка 0x61011bed часто вызывается неисправностью узла обслуживания, когда принтер не может выполнить очистку головки.
Поломка ведущей шестерни
Но сломанная шестерня в маятниковом редукторе — не единственная причина ошибки 0x61011beb и 0x61011bed. На том же валу расположена ведущая шестерня, которая также крепится на шлицах. Иногда эта шестерня слетает со шлицов и прокручивается. Обратная посадка на шлицы не решает проблему, потому что шестерня все равно слетит. Посадка шестерни на клей также ни разу не помогла больше, чем на месяц.
Решение проблемы в замене всего вала с ведущей шестерней. Цена замены вала с шестерней 2500 рублей.
HP C309h не берет бумагу
Еще одной типичной проблемой HP C309h является проблема с подачей бумаги. Если принтер не захватывает бумагу, причиной является поломка маленькой шестерни в узле захвата бумаги. Эта работа очень сложная. Для замены приходится разбирать половину принтера. Занимает ремонт по времени несколько часов. Кроме того, нужна еще и сама шестерня.
Ремонт узла захвата бумаги стоит 2500 рублей.
Читать про ремонт струйных МФУ и принтеров и ошибку системы чернил.
Еще посетители сайта интересуются :
- Ремонт захвата бумаги струйного HP
- Ремонт HP OfficeJet 7500A
Photosmart D5463 Ошибка
Общая ошибка принтера 0х61011be5
| Сообщение #1
Отправлено 28 августа 2014 — 07:55
После ручной разблокировки печатающей головки принтер высветил «Общая ошибка принтера 0х61011be5». Что делать? Может кто сталкивался, помогите.
- Наверх of the page up there ^
-
0
| Сообщение #2
Отправлено 28 августа 2014 — 12:23
palacom
Принтер не подключен к компу через USB кабель. Может в этом дело?
- Наверх of the page up there ^
-
0
| Сообщение #3
Отправлено 28 августа 2014 — 19:44
sairon2
Нет. не в этом. Как вы разблокировали ПГ?
Всем удачи и побольше прибыльной работы!)))
- Наверх of the page up there ^
-
0
| Сообщение #4
Отправлено 29 августа 2014 — 04:11
palacom
- Наверх of the page up there ^
-
0
| Сообщение #5
Отправлено 29 августа 2014 — 05:25
palacom
- Наверх of the page up there ^
-
1
| Сообщение #6
Отправлено 01 сентября 2014 — 14:20
sairon2
Как себя ведет принтер? Сразу выдает ошибку? Или пытается механику запустить? Неправильно Вы разблокировали ПГ. Там все гораздо проще. Но это уже не важно.
Всем удачи и побольше прибыльной работы!)))
- Наверх of the page up there ^
-
0
| Сообщение #7
Отправлено 02 сентября 2014 — 04:49
palacom
При включении на экране после приветствия на синем фоне возникает надпись черным по белому — типа неверное выключение принтера, нажмите ОК. Затем он шоркает головку туда-сюда, прокачивает картриджи заводит головку на парковку и выдает сообщение об ошибке. Все это происходит как при закрытой так и при открытой крышке. Хотя головка при открытой крышке должна выйти на смену картриджей.
sairon2 сказал:
Неправильно Вы разблокировали ПГ
А как надо было? (Просто в сервисе отказались — неремонтопригоден)
- Наверх of the page up there ^
-
0
| Сообщение #8
Отправлено 05 сентября 2014 — 07:45
sairon2
Если честно то да. Очень капризный принтер. И очень тяжело ремонтировать. Для начала разберите принтер и снимите место парковки. Аккуратно разберите механизм парковки. Имхо Вы пошурудили отверткой там-где этого делать не стоило. И шланги посмотрите внимательно от места парковки до выхода к памперсу(он должен стоять под местом парковки.
Всем удачи и побольше прибыльной работы!)))
- Наверх of the page up there ^
-
0
| Сообщение #9
Отправлено 05 сентября 2014 — 10:18
palacom
sairon2 сказал:
Если он такой капризный, ни сделаю ли я хуже при такой полной разборке?
sairon2 сказал:
шланги посмотрите внимательно от места парковки до выхода к памперсу
Там идет три трубки — две белых и черная. Но я ведь их не трогал.
- Наверх of the page up there ^
-
0
| Сообщение #10
Отправлено 08 сентября 2014 — 18:20
sairon2
Может быть замятие. может клинить. Может и сделаете хуже-если не имеете технических навыков. Но мы же здесь обсуждаем тему не для того, чтоб я сказал-несите в сервис? В любом случае искать надо там.
Всем удачи и побольше прибыльной работы!)))
- Наверх of the page up there ^
-
0
- ← Предыдущая тема
- Hewlett Packard
- Следующая тема →
- Вы не можете создать новую тему
- Вы не можете ответить в тему
1 человек читают эту тему
0 пользователей, 1 гостей, 0 скрытых пользователей
Скачать обновленную версию бесплатной программы PrintHelp 2023, купить Код Сброса —