Epson wf m5799 ошибка 100016

How to Fix Epson Printer Error 100016 – The drivers for Epson printers are to blame for the Epson scanner error 100016. Epson error 100016 may eventually occur as a result of a corrupted or improperly installed Epson printer driver as the main cause of delayed printing on your printer. Reinstalling the Epson printer/scanner driver typically solves the Epson 100016 issue. Therefore, if you are also an Epson Printer user and are frequently facing Error 100016 in your Epson Printer, then you have come to the right spot. Because in this blog post, we are going to address the issue that is most frequently faced by Epson Printer users i.e. How to Fix Epson Printer Error 100016, so read on.

Today, we are going to talk about the steps in order to fix Epson Printer Error 100016. There is a little number, 100016, beneath the scanner error E-02. Your printer will start up normally at first, but at odd moments, it will abruptly give you this error. Additionally, even after turning the printer off and back on, the error persists then there are several factors that could be to blame for this issue.

When the printer first turns on, it will attempt to move the scanner to the left and scan a small patch of white to verify that everything is functioning properly. Since the printer lacks eyes, it is blind to what is happening. Thus, it is dependent on a few sensors. The scanner unit may, among other things, be physically prevented from moving to the left by something, such as a dirty cable. The scanner cannot move because there is no power to the device or because something is physically blocking the scanner’s path and something mechanical is malfunctioning.

Secondly, the possibility of the lamp being burned out comes next. If there isn’t a white light, the bulb has burned out and is unable to scan the little region, making it impossible for the sensor to detect your leftward movement. Thirdly, you can have a defective mainboard, or to be more polite a poor motherboard. There shouldn’t be any physical barrier in the scanner’s path for a printer this new and clean, in your opinion. Remove it and first clean the cable. Even after this if you are still facing the issue then follow the instructions given further in our article How to Fix Epson Printer Error 100016.

Steps to Fix Epson Printer Error 100016

If the status of your printer reads “Printer in error state,” there might be an issue with the printer itself. Make sure the printer is on and wired or wirelessly connected to your PC. Make sure the cover is closed and the paper isn’t jammed, then check for low paper or ink levels. Now let’s talk about the main steps on How to Fix Epson Printer Error 100016.

1. The drivers for the Epson 4750 printer must be entirely uninstalled.
2. On the primary computer screen, press and hold the Windows Logo key while simultaneously holding down the R key (windows logo+R).
3. Type “print management” into the search box that appears in the Run Box at the bottom left of the screen and press Enter.
4. A control window for printing will show up. To expand the drop-down list and add everything under the tab, tap on Printer Servers on the window’s left side.
5. Press and look for drivers. On the right side of the window, you will now find a list of all printer drivers that have been installed in the past and present.
6. Select the driver for your Epson 4750 printer, right-click the printer, and then select Disable Package Driver.
7. The Delete button will be highlighted once the system has gathered all of the driver package information.
8. By clicking the Delete option, all information related to your Epson 4750 printer will be totally removed from your system.
9. Restart the computer after deleting the printer driver, then go to the Epson support page to download and install the most recent printer driver.

For proper and reliable support if the error still persists you can get in contact with the experts of Tech support experts now and obtain a resolution to the printers’ technical problems.

Conclusion

The bottom line is that if you are unable to swiftly resolve your Epson Printer Error 100016r, it may be inconvenient. Resetting or restarting your Epson Printer is one way you might try to solve the issue. However, if none of these fixes works, you might want to speak with a specialist. If things don’t go according to plan, you can always get in touch with Tech Support Experts for additional assistance. Tech Support Experts are here to help you with any technical errors or issues. Therefore, if our blog post on How to Fix Epson Printer Error 100016 was helpful but you still need assistance with a different technical problem, get in contact with our experts now at support@techsupportexpert.com or 800-742-9005.

Epson printers are known for their reliability and high-quality output, but like any other piece of technology, they can encounter errors from time to time. One of the most frustrating issues that can arise is the 100016 scanner error, which can prevent you from scanning documents or photos.

If you’re experiencing this error on your Epson printer, don’t panic. There are several potential causes and solutions for the 100016 scanner error, and in this article, we’ll go over them step-by-step. If you prefer a visual guide, be sure to check out the accompanying video that covers the same information.

Before we dive into the troubleshooting steps, let’s take a moment to discuss what the 100016 scanner error actually means. This error code indicates that there is an issue with the scanner module of your Epson printer. It could be caused by anything from a hardware malfunction to a software issue.

The good news is that the majority of causes for the 100016 scanner error can be resolved without the need for professional assistance. Here’s what you can do:

Restart your printer

1. The simplest solution is often the best place to start. Turn off your printer, unplug it from the power source, wait a minute or two, and then plug it back in and turn it on. This will allow your printer to reset itself, which can sometimes fix the 100016 scanner error.

Update your printer’s firmware and drivers

2. Outdated or corrupt firmware and drivers can cause a range of issues on your printer, including the 100016 scanner error. To update your printer’s firmware and drivers, visit the Epson website and navigate to the support page for your specific model. Download and install any available updates, then restart your printer and see if the error has been resolved.

Check the scanner module

3. In some cases, the scanner module may have become disconnected or damaged, which can lead to the 100016 scanner error. To check the scanner module, turn off your printer and unplug it from the power source. Carefully remove the scanner module from your printer and check for any signs of damage or loose connections. If you find any issues, try reconnecting any loose cables or replacing any damaged parts.

Run a scanner diagnostic

4. If none of the above steps have resolved the issue, try running a scanner diagnostic. To do this, navigate to the settings menu on your printer and select the option for scanner diagnostics. Follow the on-screen instructions to complete the diagnostic, which will check for any underlying issues with your printer’s scanner.

Contact Epson support

5. If you’ve tried all of the above steps and the 100016 scanner error persists, it may be time to contact Epson support for further assistance. You can find their contact information on their website or in your printer’s user manual.

The 100016 scanner error on your Epson printer can be frustrating, but it’s not the end of the world. By following the above steps, you can troubleshoot and resolve the issue in most cases. If you’re still experiencing the error, don’t hesitate to reach out to Epson for further assistance.

Apr 26th 2023 Jee Comendador

Ошибка Е-01 Epson XP SX WF

Ошибка Е-01 в Epson XP SX WF серии является серьезной критической ошибкой. Она обычно проявляется сразу до движения каретки. Не стоит верить полной ерунде, которую пишут на некоторых сайтах. Например, что E01 вызывается только ошибкой нижнего датчика картриджей или не вставленным шлейфом сканера. Если не вставлен шлейф сканера, принтер будет печатать.

Что означает ошибка E-01 (E01)

Ошибка Е-01 имеет подкоды, которые обозначают область неисправности. Epson по непонятной причине придумала еще одну кодировку ошибок, хотя уже давно использовала кодировку в 16-ричной системе. Коды ошибок струйных принтеров Epson с расшифровкой.

0000XX ошибки стартовой диагностики

000020-000033 проблемы движения каретки.

000040-000053 проблемы узла подачи бумаги.

Ошибки сканера 1000XX

060001  Scanner failure — ошибка сканера.

100000-100014 неисправности автоподатчика ADF

100016 — ошибка сканирующей линейки сканера.

100020 — Measurement error, Scanner drive mechanism was overloaded -перегрузка привода сканера

100032 LED light error — ошибка подсветки

Проблемы головки 031001-031007

031001 HeadHot detect error (pre printing). Перегрев головки перед печатью, обрыв, повреждение шлейфа головки, неисправность платы. Происходит в перерывах печати перед следующей печатью.

031002 HeadHot detect error (after flushing) перегрев головки после прочистки. Причины — головка, плата, шлейф.

031003 Transistor temperature error перегрев транзисторов на плате.

031004 Head temperature error обычно перегрев термистора в головке. Температура вне диапазона -20 to 80 град. цельсия.

вариант 031004 — PrintHead not responding — не отвечает печатающая головка.

031006 — Failure of the power source for the printhead (нет питания на печатающей головке). Причины:  нет контакта в шлейфе, обрыв, перегорел предохранитель на плате управления, неисправность головки или платы управления.

031007 Power off error due to abnonal printing Отключение питания из-за неправильного управления головкой.

033001-033009 — неисправность главной платы управления

033001 — 0x80, перегорел предохранитель F1. Обычно ошибка появляется из-за того, что залили головку.

000041 — эта же ошибка обозначена у Эпсон как 0x29 PF PID. Варианты: избыточная нагрузка PF (подачи бумаги), отсоединен кабель или FFC, проскальзывание или нет натяжения ремня,  двигатель PF, энкодер PF, выскочил кабель датчика, посторонний предмет или бумага, главная плата.

000031 или 000033 — ошибки, связанные с замятием бумаги. А также возможно, что заедает каретка. Например, картриджи задевают за крышку, заедают трубки СНПЧ. Еще возможна неисправность узла обслуживания.

000031 — CR load position excess load error (ошибка позиционированияф каретки)
PF Motor failure- PF drive mechanism overload (paper jam, foreign object)- Tooth skip of the PF Timing Belt- Improper tension of the PF Timing Belt- Cable disconnection». В общем, то же самое, что и при 000041. Но чаще всего ошибка E01 000031 появляется при неправильной установке крышки шлейфа с левой стороны каретки. Ошибка «Кривые руки».

033501-033509 ошибки картриджей

033501 ILS light error — невозможно определить наличие чернил в картриджах из-за сильной засветки датчика снаружи. Закрыть посторонние источники света.
033503 — PIS no reflected light error. Ошибка считывания наличия чернил в картриджах. Reflector no reflection error (нет сигнала отраженного света). Ошибка платы датчика чернил (контакты, отражатель). Например, проблема rn- Sensor (неисправный датчик, поврежден шлейф, неправильно положение PIS Boardrn, грязь. Эта же ошибка 0x82 — отсутствие отражения от рефлектора под кареткой. Fault Detection Plate failure — ошибка платы регистрации проблемы. Как устранить ошибку: чистка сенсора, чистка отражающего рефлектора, заклеиваем отверстия черной изолентой под картриджами, замена сенсора.

033504 ILS abnormal error — показания датчика вне диапазона. Проблема rn- Sensor (неисправный датчик, поврежден шлейф, неправильно положение PIS Boardrn.
033505 ILS Empt jig error. No occures except in manufacturing prodess.»

033506 0x88 Light excessive error. Превышение уровня света. Слишком высокий уровень сигнала с датчика. Возможно, посторонняя засветка, открыта крышка, рядом источник света. Abnormal sensor output — слишком большой сигнал с датчика чернил. Ошибка сенсора или всей платы (sensor failure, PIS board failure). Возможно, что из-за посторонней засветки, например, прямого солнечного света.

033507 Insufficient light error. Недостаточный уровень света на датчике чернил в картриджах. Слишком низкий уровень сигнала. Ошибка датчика (неправильная установка), повреждение шлейфа, платы датчика, слишком много постороннего света, неисправность чернильных картриджей (грязные, повреждена призма). Та же ошибка 0x89 — Insufficient light error (ошибка недостаточной интенсивности света на датчике). Далее куча вариантов с ошибкой сенсора. Sensor failure (PIS board installation failure, contaminated sensor), abnormal sensor output (break of FFC during printer operation, PIS board failure), unable to accurately detect where the fault detection plate is because too much diffused light from outside is shed on the sensor (when used outdoors or near the window where direct sunlight comes in), ink cartridge failure (contaminated/damaged prism). В частности, из-за посторонней засветки. Действия при ошибке: чистка датчика, заклеиваем отверстия черной изолентой под картриджами, замена датчика. А также убираем постороннюю засветку. Например, закрываем крышку.

Ошибки движения

034001 Home position error — невозможно найти начальное положение каретки. Возможно: перегрузка привода каретки, посторонние предметы, деформация рамы, замятие бумаги, рычаг освобождения бумаги, узел обслуживания, двигатель каретки, плата управления.

034004 Insoluble paper jam error. Замятие бумаги, посторонние предметы, деформация рамы, рычаг освобождения бумаги.

034010 PF runaway error. Дисковый энкодер PF, двигатель подачи бумаги.

034011 APG target position acquisition error — ошибка механизма подъема каретки. Причины: двигатель APG, датчик APG, плата управления.

034500 Ink cartridge replacement timing contact detection error — ошибка определения картриджей при замене по времени. Возможно, картридж вылетел из посадочного места и задевает за корпус.

034503 — Contact error at I/S clutch operation. Это ошибка 0x69 системы чернил.

Залили контакты головки чернилами

Ошибка Е01 чаще всего связана с залитием шлейфа головки чернилами. Выгорает часть шлейфа.

Далее обычно сгорает SMD предохранитель F1 на плате управления, что и обнаруживает принтер.

На фото в кружке отмечен сгоревший предохранитель F1 номиналом 1.5А.

Эта неисправность проявляется принтерах Эпсон серии ХР, например, XP-33, 103,  203,  206,  303,  306,  313,  323,  332,  340,  342,  403,  406,  413,  430 и др. Обычно залитие чернилами шлейфа головки происходит из-за неисправного картриджа или СНПЧ.

2 вариант ошибки Е-01

В SX-430 ошибку Е01 вызывала неисправная печатающая головка. Реальный код ошибки был 0x43, что означает Head Hot Error. Т.е. сенсор фиксирует ее перегрев. Но с такой неисправностью устройство работать не будет. И никакая чистка не поможет. Только замена головки.

Ошибка E01 000041 возникала в XP-342 только при попытке захвата бумаги.

Подобную ошибку вызывает проблема с подачей бумаги. Энкодер подачи бумаги с датчиком, двигатель, ремень, натяжитель, а также сам узел захвата.

Например, в одном случае чистка грязного энкодера и датчика не помогла. Потому что проблема была в ролике отделения.

Его заклинило.

Что делать в случае ошибки E01?

В первую очередь нести в сервис, сами вы эту проблему не решите. В сервисе должны:

• прочистить головку от чернил, высушить ее;
• картридж, который протек, нужно заменить или починить;
• испорченный шлейф восстановить или заменить;
• разобрать МФУ и вынуть плату управления, перепаять предохранитель, собрать обратно.

Стоимость такой работы по ремонту Epson XP в Комплэйс составляет около 3000 руб.

Проблемы при ошибке E01 в принnерах Epson

Если ошибка E01 появляется не сразу при включении, то то это не страшно. Ремонт не будет очень дорогой.

Но когда ошибка выскакивает сразу, без движения каретки, то дело хуже. Однако, даже если была залита головка, восстановление при ошибке E-01 возможно. Но есть и нюансы.

Например, может выйти из строя головка. Стоимость новой около 5000 рублей, установка ее 1000 рублей. В этом случае ее нужно заменить, а также починить плату управления и шлейф. Это все дорого.

Можно ли отремонтировать главную плату?

Кроме предохранителя может сгореть микросхема драйвера головки. В подобном случае нужно менять всю плату. Ее стоимость около 2500-3000 рублей. Восстановление шлейфа обойдется 1500 рублей.

Если принтер совсем не включается, то вышли из строя транзисторы. Такую плату лучше вообще не чинить. Потому что новые транзисторы могут опять выйти из строя.

Today we’re going to solve a problem for Epson EcoTank. The scanner error E-02 and there’s a small number underneath, 100016. You’ll find your printer start okay, and at random times, suddenly, you’ve got this error. You also turn off the printer, and turn it back on, and the failure doesn’t go away. Now, this problem may be caused by a couple of things.

At power-on, the printer will try to move the scanner to the left and scan a small patch of white as a signal that everything works okay. The printer doesn’t have eyes, so it doesn’t know what’s going on. It depends on a couple of sensors. First thing, you may have something physically make the scanner unit not able to move to the left, including you have a dirty cable. So there’s no power to the unit and the scanner cannot move, or you have something physically obstruct the pathway of the scanner and something mechanical.

The next thing is the lamp might be burnt out. If you don’t see a white light, that means the bulb burnt out so it cannot scan the little patch, so the sensor will not be able to recognize you moving to the left. Thirdly, you might have a bad motherboard or, to be politically correct, he mainboard. For a printer very new and this clean, I don’t suspect any physical obstruction for the movement path of the scanner. I’ll take it out, and I’ll clean the cable first.

I hope you can find out it’s just a dirty cable or a misplaced cable. However, if everything doesn’t work out, you can always find spare parts by going to www.bchtechnologies.com, and then go to the printer parts. Go to Epson and see if we have spare parts for you. ET-2720 is easy to take apart and remove the two screws in front. Example, sides. Now, you can lift the whole scanner unit. There are three cables, and they’re in different sizes, so don’t worry about mixing them. Pull them out and clean them.

I’ll take a dry cloth, start cleaning. If you use sandpaper, use a super, superfine, like a 2,000 grit sandpaper. Most times, the dry cloth do the work. You don’t need to go to the sandpaper. Another thing you can try is to use the rubber eraser. To insert the cable back, it’s easier to take the side panel off. Use a screwdriver or something to push the tab in and then use your hand. Just jiggle it, and you can take the whole cover off.

Now, pay attention to which direction the cable goes in. From the smallest cable, you can see the contact points are on the top and the medium cable contact points on the bottom. For the cable, the smallest cable, the shiny side should be on the top, and the blue side should be on the bottom. For the medium cable, the blue side should be on the top, and the shiny side should be on the bottom. Now, we put the bigger cable just like the two other cables on the side. There’s a sticky double-sided tape that helps us to stabilize the wires.

Please don’t put the side cover back yet because we’re going to plug in power to see it works. If it doesn’t have power, that’s because your bigger cable is not installed correctly, try to reinstall it. Now, you can see it can move. The problem’s solved. Otherwise, you may have to take the scanner unit apart and see all the sensors and see if there are mechanical problems.

Try to use or color copy a page before you put the side panel back. Now we know the scanner is working. The only problem is it seems the nozzles are clogged. Now we can put the side panel back and then insert the two screws in the front, and the unit is ready for some nozzle cleaning. After that, it’s ready to go.

Aug 24th 2020

How To Fix Epson Printer Error 100016- Steps

Epson printers are known for their reliability and performance, but like any other electronic device, they can encounter errors from time to time. One such error is Epson Printer Error 100016, which can disrupt your printing and scanning tasks. If you are facing this error and seeking a solution, you’ve come to the right place. In this article, we will guide you through the troubleshooting steps to fix Epson Printer Error 100016.

Understanding Epson Printer Error 100016

Epson Printer Error 100016 is typically associated with scanner-related issues. It occurs when there is a problem with the scanner functionality, preventing the printer from completing scan jobs or displaying error messages. This error can occur due to various reasons, such as outdated drivers, software conflicts, or issues with the scanner hardware.  This error can prevent the printer from completing scanning tasks or result in error messages being displayed on the printer’s control panel. To effectively address this error, it is important to understand its underlying causes. Printer drivers serve as the communication bridge between the printer and the computer. If the printer drivers are outdated or incompatible with the operating system, it can lead to errors, including Error 100016. Updating the printer drivers to the latest version can often resolve this issue. Whether it involves updating printer drivers, addressing software conflicts, or checking hardware connections, diagnosing the root cause of the error is crucial in finding an effective solution.

Restart the Printer

A simple yet effective solution for many printer errors, including Error 100016, is to restart the printer. Turn off the printer, unplug it from the power source, and wait for a few minutes. Then, plug it back in and turn it on again. This can help clear any temporary glitches and reset the printer’s internal settings. 

Here’s how to restart your Epson printer:

1. Turn off the printer: Locate the power button on your Epson printer and press it to turn off the printer. If the printer doesn’t have a power button, unplug it from the power source.
2. Wait for a few minutes: Give the printer a few minutes to completely power down. This allows any residual power to dissipate and ensures a fresh start when you turn it back on.
3. Turn on the printer: After waiting for a few minutes, press the power button to turn on the printer. If you had unplugged the printer, plug it back into the power source and then turn it on.
4. Test the printer: Once the printer has restarted, try performing a test print or scan to see if the error message has been resolved. Check if the scanner functions properly without displaying Error 100016.

Update Printer Drivers

Outdated or incompatible printer drivers can often lead to errors. Updating the printer drivers can help resolve various printer-related issues, including Error 100016. Visit the Epson website or ExcelTechGuru.com for the latest printer drivers for your specific printer model. Download and install the updated drivers following the provided instructions.

Check for Software Conflicts

Sometimes, software conflicts can cause scanner errors on Epson printers. Software conflicts can contribute to Epson Printer Error 100016 and hinder the scanner functionality of your Epson printer. Identifying and resolving software conflicts can help resolve the error and restore normal printer operations. ExcelTechGuru.com provides valuable guidance and information on how to check for software conflicts effectively.Ensure that there are no conflicting programs or applications running in the background. Close unnecessary programs and temporarily disable any security software or firewalls that might interfere with the scanner functionality.

When checking for software conflicts, start by closing any unnecessary programs running on your computer. These programs might interfere with the scanner functionality of your Epson printer. By closing them, you reduce the chances of conflicts and allow the printer to function smoothly. It is advisable to check for any updates or patches available for these conflicting programs. Updating or reinstalling the conflicting software can help resolve software conflicts and eliminate Epson Printer Error 100016.

By following the instructions and recommendations provided by ExcelTechGuru.com, you can effectively identify and address software conflicts that may be causing the error. Resolving software conflicts can improve the scanner functionality of your Epson printer and ensure smooth printing and scanning operations.

Perform a System File Check

System file corruption can also contribute to scanner errors. Perform a system file check to scan and repair any corrupted system files. Open the Command Prompt as an administrator and run the “sfc /scannow” command. Allow the process to complete, and if any corrupted files are found, they will be automatically repaired.

Reinstall the Scanner Driver

If the scanner driver is corrupted or improperly installed, it can lead to Error 100016. Uninstall the scanner driver from your computer and reinstall it using the latest version available from the Epson website or the installation CD that came with your printer. Follow the instructions provided during the installation process.

Check Scanner Connections

Ensure that all the scanner connections are secure and properly connected. Disconnect and reconnect the scanner cables, including the USB or Ethernet cable, to ensure a proper connection. Make sure there are no loose or damaged connections that could be causing the error. Examine the connections for any visible damage or debris that might affect the communication between the scanner and the computer. By ensuring proper and secure connections, you can eliminate connection-related issues and potentially resolve Epson Printer Error 100016.

Run the Epson Scan Utility

Epson provides a dedicated scanning utility called Epson Scan Utility. Running this utility can help diagnose and resolve scanner-related errors. Locate the Epson Scan Utility on your computer and run it. Follow the on-screen instructions to scan for errors and troubleshoot any issues that are detected.

Perform a Scanner Test

Epson printers often have a built-in scanner test feature. Access the printer’s control panel or settings menu to find the scanner test option. Run the scanner test to check the functionality of the scanner. Locate the Epson Scan Utility on your computer, launch the application, and follow the on-screen instructions. The utility will scan for errors and guide you through the troubleshooting process. By utilizing the Epson Scan Utility, you can identify and resolve any underlying issues that may be causing Error 100016, ensuring the smooth functioning of the scanner and eliminating the error. If any errors or issues are detected during the test, consult the printer’s user manual or Epson’s support resources for further guidance.

Conclusion

Epson Printer Error 100016 can be frustrating, especially when you need to perform scanning tasks. However, by following the troubleshooting steps outlined in this article, you can resolve the error and get your Epson printer scanner back in working order. Remember to restart the printer, update printer drivers, check for software conflicts, and perform necessary tests and scans. For more detailed instructions and information on Epson printer errors and solutions, visit ExcelTechGuru.com. ExcelTechGuru.com offers a wealth of resources and support to help you troubleshoot and fix various printer-related issues, including Epson Printer Error 100016.