centigrade.
Q:
Low Airflow when «Air» Dial is Turned Up
A:
If you are getting low airflow when the «Air» Dial is turned up, make sure
that you have the nozzle securely attached. With the nozzle, you will get more
air flowing through the hot-air rework station’s handle.
S-E Error
«S-E» usually means Sensor Error. It’s a common error. Sometimes it goes
away after messing with the dial and the temperature will display properly
again. Other times it indicates that the heat sensor is failing. The rework station
might be able to be revived by removing and re-attaching the heater. Another
tech support rep thinks it’s oxide building up on the connections. This results in
fooling the controller into thinking the heater has failed.
H-E Error
Units displaying the «H-E» usually means there is a heating error. It might be
that there is something with the heating element failing or not connected
properly. Try checking the connections to see if the heating element needs to
be re-seated. Last resort is getting a replacement heating element. A last
resort is getting a replacement heating element.
Air Turned Too High
If your air flow is turned up too high, it is quite possible that you will start seeing
small projectiles shooting away from your board. Those are your parts. We
recommend starting at a lower air flow and moving up as your needs require.
Destroying a PCB
If you sit too long on a given spot on a PCB while working with hot-air, the glue
that holds the copper layer to the FR4 laminate underneath lets go and comes
out as black goo. The green solder mask on the top side also begins to come
off. Because we don’t have Smell-a-vision yet, we can try to describe the smell
— it’s horrendous. It smells like burning electronics (surprise) but the smell
seems to cling to your skin and clothes. Not cool. So practice and don’t be
surprised if you smell bad things with your first couple re-work attempts.
|
|
#1 |
|
Badcaps Veteran
Join Date: Dec 2011 City & State: Kucova, Albania My Country: Albania Line Voltage: 220V 50Hz I’m a: Student Tech Posts: 301 |
Its only a week i have been working with my new Atten 858D+ heating station and i have experienced a problem. The station showed S-E in the digital display, the blower fan was ok but it was NOT heating. Searching the web showed that the heating element was gone, this was an error code, but it was not true. Measuring it showed 70 Ohms. Also the mosfet which drives it was not shorted. The station was also stuck in 498’C sometimes, again no heat. First pic is the Atten 858D+. At the moment it is OK, SLP means «sleeping». |
|
|
|
|
#2 |
|
Badcaps Veteran Join Date: Apr 2010 City & State: Canada Posts: 9,200 |
Quote:
Originally Posted by senndogg Mine is in warranty too but i was not thinking about shipping it ti China. Good job on repairing it. Someone who lives in Hong Kong theorizes that some sellers in China bank/rely on the fact that shipping defective goods back to China costs so much that most people don’t bother.
__________________ If you are new to this forum, we can help a lot more if you please post clear focused pictures (max resolution 2000×2000 and 2MB) of your boards using the manage attachments button so they are hosted here. Information and picture clarity compositions should look like this post. We respectfully ask that you make some time and effort to read some of the guides available for basic troubleshooting. After you have read through them, then ask clarification questions or report your findings. Please do not post inline and offsite as they slow down the loading of pages. — end sig file — |
|
|
|
|
|
#3 |
|
Badcaps Veteran
Join Date: Feb 2010 City & State: S.F. Bay area My Country: USA Line Voltage: 120V 60Hz I’m a: Knowledge Seeker Posts: 39,206 |
Chinese quality workmanship. I had been to China 5 times to inspect the products they put together for us, after Chinese New Year is over, they always get the new workers since the original workers that were trained went back home for the new year and do not want to come back, so the products made after new years are always problems for us. They just cannot retain their workers which I do not blame the workers at all due to the condition they have to live, they basically live in the dorms on the factory site. |
|
|
|
|
|
#4 |
|
Badcaps Veteran
Join Date: Dec 2011 City & State: Kucova, Albania My Country: Albania Line Voltage: 220V 50Hz I’m a: Student Tech Posts: 301 |
sad but true. this is claimed to be one of the best «in-home» manufactured heating station but overall quality is far from good. |
|
|
|
|
|
#5 |
|
Badcaps Veteran Join Date: Jan 2010 City & State: Northern Norway My Country: Norway Line Voltage: 230VAC 50Hz I’m a: Knowledge Seeker Posts: 384 |
This was a nice fix — glad you got it working again. What kind of programmer did your friend buy ? |
|
|
|
|
|
#6 |
|
Badcaps Veteran
Join Date: Dec 2011 City & State: Kucova, Albania My Country: Albania Line Voltage: 220V 50Hz I’m a: Student Tech Posts: 301 |
i dont know exactly, but it was for automotive use. maybe one for coding Airbag ECUs for VAG family or chrome Mercedes smart keys. I remember that the chinese cheapo was 1/10 of the original price. |
|
|
|
|
|
#7 |
|
Badcaps Veteran Join Date: Apr 2010 City & State: Canada Posts: 9,200 |
Quote:
Originally Posted by senndogg a friend of mines shipped back a programmer, which by the way was fake, he paid almost the same price for it to be shipped, and they sent back another defective one. trying to contact them was useless. If it was purchased through ebay, don’t send it back. Open a case and say it is counterfeit and ebay will likely refund the purchase price + shipping. |
|
|
|
|
|
#8 |
|
Badcaps Veteran
Join Date: Dec 2011 City & State: Kucova, Albania My Country: Albania Line Voltage: 220V 50Hz I’m a: Student Tech Posts: 301 |
nope! they arranged via email and everything was on behalf. |
|
|
|
|
|
#9 |
|
New Member Join Date: Oct 2013 City & State: lima My Country: peru I’m a: Knowledge Seeker Posts: 2 |
Quote:
Originally Posted by senndogg Its only a week i have been working with my new Atten 858D+ heating station and i have experienced a problem. The station showed S-E in the digital display, the blower fan was ok but it was NOT heating. Searching the web showed that the heating element was gone, this was an error code, but it was not true. Measuring it showed 70 Ohms. Also the mosfet which drives it was not shorted. The station was also stuck in 498’C sometimes, again no heat. First pic is the Atten 858D+. At the moment it is OK, SLP means «sleeping». i have the 858d+, but the heat is about 100C, not 450c, the seller say is bad the heating coil, the wanna sell the replacement, can you helpme? thanks!!! |
|
|
|
|
|
#10 |
|
Badcaps Veteran Join Date: Nov 2011 City & State: Tasmania My Country: Australia Line Voltage: 230VAC I’m a: Knowledge Seeker Posts: 670 |
this is my problem there is a short is there anywhere I can buy a new thermo coupler? whats the parts called. |
|
|
|
|
|
#11 |
|
I see dead caps
Join Date: Oct 2007 City & State: Hiding inside a plated-through hole My Country: New Zealand Line Voltage: 230VAC 50Hz I’m a: Hobbyist Tech Posts: 4,700 |
Is the thermocouple part of the heater? If so you can get the thing here: http://www.ebay.com/itm/858-898-898D…-/360847659151
__________________ |
|
|
|
|
|
#12 |
|
New Member Join Date: Jul 2015 City & State: Valdivia My Country: chile I’m a: Knowledge Seeker Posts: 1 |
Hi, mime give me an «Err», that meas de coil is broke, but is not. Greetings |
|
|
|
|
|
#13 |
|
I see dead caps
Join Date: Oct 2007 City & State: Hiding inside a plated-through hole My Country: New Zealand Line Voltage: 230VAC 50Hz I’m a: Hobbyist Tech Posts: 4,700 |
Perhaps the trimmer has broken when you adjusted it? Check the solder did not break on the leads or something. |
|
|
|
|
|
#14 |
|
Great Sage 齊天大聖
Join Date: Dec 2009 City & State: Europe My Country: some shithole run by Israeli agents I’m a: Professional Tech Posts: 29,036 |
what is the soldering like? some of the chinese units are terrible and you need to resolder most of the board!!! |
|
|
|
|
|
#15 |
|
New Member Join Date: Nov 2017 City & State: Chambly My Country: Canada I’m a: Knowledge Seeker Posts: 10 |
Hi to all, I have a Sigma R700 (858D clone) and would like to repair it. PCB is marked SBK858D 2017.01.03 The heater is always ON no matter it is on the holder or not. I troubleshooted the whole circuit and the reed switch is good. Am I missing something here ? Any other conditions in the firmware would keep the heater ON all the time ? Thanks ! |
|
|
|
|
|
#16 |
|
I see dead caps
Join Date: Oct 2007 City & State: Hiding inside a plated-through hole My Country: New Zealand Line Voltage: 230VAC 50Hz I’m a: Hobbyist Tech Posts: 4,700 |
Whatever controls the heater, probably a Triac, may be shorted? |
|
|
|
|
|
#17 |
|
New Member Join Date: Nov 2017 City & State: Chambly My Country: Canada I’m a: Knowledge Seeker Posts: 10 |
Quote:
Originally Posted by Agent24 Whatever controls the heater, probably a Triac, may be shorted? I originally thought about it but it controls according to temp setpoint. This part seems to work. |
|
|
|
|
|
#18 |
|
Great Sage 齊天大聖
Join Date: Dec 2009 City & State: Europe My Country: some shithole run by Israeli agents I’m a: Professional Tech Posts: 29,036 |
so your saying the standby function isnt working, but it heats to whatever temperature you set? |
|
|
|
|
|
#19 |
|
New Member Join Date: Nov 2017 City & State: Chambly My Country: Canada I’m a: Knowledge Seeker Posts: 10 |
Quote:
Originally Posted by stj so your saying the standby function isnt working, but it heats to whatever temperature you set? That is exactly right |
|
|
|
|
|
#20 |
|
Great Sage 齊天大聖
Join Date: Dec 2009 City & State: Europe My Country: some shithole run by Israeli agents I’m a: Professional Tech Posts: 29,036 |
not much to it if it matches either of these: |
|
|
|
I took out my soldering iron ready to soldering random stuff and was very sad to find that it was displayed the error “S-E” or “5-E” instead of the temperature displayed. I quickly googled some stuff quickly realized that the soldering element had gone bad. I’ve had the soldering iron for about 4-5 years and it’s always worked great, never dropped it or was rough with it, but eventually the heating element will go bad.
Problem: Error “S-E” or “5-E” displayed on the screen
Solution
- Replace the soldering iron’s heating element.
I’ve created the video below showing how I replaced the heating element on my soldering iron.
Комментарии 10
Войдите или зарегистрируйтесь, чтобы писать комментарии, задавать вопросы и участвовать в обсуждении.
пользуюсь уже пол года проблем не знаю . А для пайки пластика подойдет мне кажется и обычный строительный фен+ грамотно подобранные насадки .
Наверное самые качественные это BAKU
У меня AIFEN 892A+ уже пользуюсь лет 5…
3 года он работал на ремонте сотовых, постоянно включенный, вроде работает нормально.
На работе пользуюсь Lukey 868, уже больше года, до этого она в нашем сервисном центре работала весьма активно, думаю надёжный аппарат .
Паяльная станция Lukey 702👍
Лучше купить сам фен (хороший, качественный) и примастырить к станции, подключения у них почти у все одинаковое, так дешевле обойдется.
Или поищи у себя нагревательный элемент.
Со второй попытки у меня самоубился такой фен
таже беда 2 фена выбросил) идешь и покупаешь фен отдельно есть в продаже)
У меня такая же станция, только BAKU.Один в один.Паяльник уже второй раз расплавился…
| Автор | Сообщение |
|---|---|
|
Заголовок сообщения: Паяльная станция Gordak 952 фен не работает ошибка S-E
|
|
|
|
проблема такая:Фен не работает,когда включаю ошибка входить S-E ,паяльник работает Пожалуйста помогите что нужно сделать ? Спираль от фена поменял )) |
| Вернуться к началу |
|
 |
Добавлено: 12 окт 2016 09:28 
|
YX-360TR |
Заголовок сообщения: Re: Паяльная станция Gordak 952 фен не работает ошибка S-E
|
|
|
обрыв термопары у фена.. проверь провода, замени пару. Если не поможет — проверить ОУ, стоящий в усилении термопары, обычно это ЛМ358 |
| Вернуться к началу |
|
|
|
majo |
Заголовок сообщения: Re: Паяльная станция Gordak 952 фен не работает ошибка S-E
|
|
|
Здравствуйте а что такое термопара ? и как выглядеть? прошу прошение! |
| Вернуться к началу |
|
|
|
Abdurauf |
Заголовок сообщения: Re: Паяльная станция Gordak 952 фен не работает ошибка S-E
|
|
|
majo писал(а): Здравствуйте а что такое термопара ? и как выглядеть? прошу прошение! термопара это датчик температуры. Он у вас в конце фена (внутри). |
| Вернуться к началу |
|
|