Error codes (fault codes) reference of ES200 automatic door malfunctions (Dorma ES200 applicable).
ERROR CODES (FAULT CODES) REFERENCE – ES200
Error Code 0 – No error
Error Code 1 – Obstruction
Error Code 2 – Lock error
Error Code 3 – Program switch malfunction
Error Code 4 – Light barrier / safety sensor error
Error Code 5 – Incremental encoder malfunction
Error Code 6 – Backup battery (accumulator) failure
Error Code 7 – System error
Error Code 8 – Emergency Stop malfunction
Error Code 9 – Learning cycle parameter error
Error Code A – Motor malfunction
Error Code c – Force test failure
Error Code d – Over current at motor
Error Code F – DCW error
Error Code L – Relay test failure
General Measures:
- Set program switch to AUTOMATIC – CLOSE – AUTOMATIC.
- Power off, wait for 20 seconds, power back on.
- Run automatic learning cycle
Above measures are general solutions, real cause can be various, need carefully checking on door panels and rail, make sure the movement is smooth, and all wire connections are steady, especially good contact at the control terminals.
Reference:
- Restore ES200 original factory settings.
Error codes (fault codes) reference of ES200 automatic door malfunctions (Dorma ES200 applicable).
ERROR CODES (FAULT CODES) REFERENCE – ES200
Error Code 0 – No error
Error Code 1 – Obstruction
Error Code 2 – Lock error
Error Code 3 – Program switch malfunction
Error Code 4 – Light barrier / safety sensor error
Error Code 5 – Incremental encoder malfunction
Error Code 6 – Backup battery (accumulator) failure
Error Code 7 – System error
Error Code 8 – Emergency Stop malfunction
Error Code 9 – Learning cycle parameter error
Error Code A – Motor malfunction
Error Code c – Force test failure
Error Code d – Over current at motor
Error Code F – DCW error
Error Code L – Relay test failure
General Measures:
- Set program switch to AUTOMATIC – CLOSE – AUTOMATIC.
- Power off, wait for 20 seconds, power back on.
- Run automatic learning cycle
Above measures are general solutions, real cause can be various, need carefully checking on door panels and rail, make sure the movement is smooth, and all wire connections are steady, especially good contact at the control terminals.
Reference:
- Restore ES200 original factory settings.
-
#21
Они без остановки катаются или есть какие то периоды и т. д.
-
#22
Они без остановки катаются или есть какие то периоды и т. д.
без остановки, закрылись полностью-открылись полностью. как будто створка препятствие ловит…
-
#23
Похожая ситуация бывает при снятом и висящим коробом, с установленым радаром, двери могут бесконечно работать. Если было бы препятствие, через сколько то циклов ушли бы в обслуживание, еррор. Других версий, кроме неправильно настроенного радара у меня пока нет…
-
#24
короб не обязательно болтается (хотя не исключено), встречал случаи когда радар створки собственные видит… диагностировать достаточно просто, надо отключить радар и посмотреть что будет, можно загрубить настройку радара, но это сложнее для начинающих диагностов )
-
#25
встречал случаи когда радар створки собственные видит… )
Это и имел ввиду, когда болтается на страховках, радар направлен на двери.
-
#26
короб не обязательно болтается (хотя не исключено), встречал случаи когда радар створки собственные видит… диагностировать достаточно просто, надо отключить радар и посмотреть что будет, можно загрубить настройку радара, но это сложнее для начинающих диагностов )
Приветствую! Датчиков(радаров) два, откидывал сначала один, потом другой. Обучается, и гоняют по кругу как обычно… Чувствительность ставил на 1ку. Тоже не помогло. Без двух сразу, понятное дело ошибка.
-
#27
Это и имел ввиду, когда болтается на страховках, радар направлен на двери.
Привет! Ничего не болтается там( Ну короче, навязали мне двери, мол хочешь работать, бери еще и их, денег конечно прибавили к ежемесячному, но и гемора тоже. Итого 96 магазинов, где одна дверь, где две, где то три. ФААСЫ, ДОРМЫ, ТОРМАКСЫ.
-
#28
Привет! Ничего не болтается там( Ну короче, навязали мне двери, мол хочешь работать, бери еще и их, денег конечно прибавили к ежемесячному, но и гемора тоже. Итого 96 магазинов, где одна дверь, где две, где то три. ФААСЫ, ДОРМЫ, ТОРМАКСЫ.
Да ты миллионер батенька. У нас раценка 1 дверь примерно добавляется 1000 — 1200 руб/мес.
-
#29
Да ты миллионер батенька. У нас раценка 1 дверь примерно добавляется 1000 — 1200 руб/мес.
Посмотрим как будет)
По теме самокатающихся дверей, в итоге там пролило крышу, двери выключены, электричества в тамбуре там нет, так что пока ничего делать там не буду. Пробую набрать блоков моторов датчиков. Буду дам все по кругу перекидывать.
Каретки,треки еще до кучи взял
-
#30
Возможно непропай в энкодере мотора. На старых дверях они собирались с односторонней пайкой (Дорма, Тормакс). Регулярно у нас в Самаре с такой причиной сталкивался. Самое правильное все откинуть поставить перемычки и замыкая контакты радара проверить работоспособность блока, но сначала глянуть кодер. Большинство монтажников не знают про эту фишку.
-
#31
Возможно непропай в энкодере мотора. На старых дверях они собирались с односторонней пайкой (Дорма, Тормакс). Регулярно у нас в Самаре с такой причиной сталкивался. Самое правильное все откинуть поставить перемычки и замыкая контакты радара проверить работоспособность блока, но сначала глянуть кодер. Большинство монтажников не знают про эту фишку.
Залатали крышу, позвонили, мол приезжай запускай) Приехал, откидываю крышку….а движка и блока нет))) спи…и подрядчики, по горячим следам выяснили кто, уехали наши железки в Курск вот жду когда пришлют обратно.
-
#32
Всем привет! Оборудование вернули,подключили, собственно вот такие пироги
http://www.youtube.com/watch?v=2EmwV3hJZZ4
Сняли блок управления, поставили на работающую дверь, обучили, он работает отлично.
Мотор при подключении ведет себя одинаково. Е-5(энкодер). Протереть, пропаять пробовали.
Получается меняем двигатель?
И правда ли что Дорма продает только блок мини-драйв, т.е. мозги+мотор?
-
#33
Насколько мне известно, то они продают отдельно мотор-редуктор от мозгов. Просто цена будет всего на 10-15 % меньше чем привод целиком(мозги, каретки, мотор)
-
#34
Насколько мне известно, то они продают отдельно мотор-редуктор от мозгов. Просто цена будет всего на 10-15 % меньше чем привод целиком(мозги, каретки, мотор)
Согласен))) 566 евро минидрайв в сборе))) мотор отдельно 598 евро… озверину наелись ребята….
-
#35
Всем привет. Ребят выручайте.в дверях новичок. чтобы темы не плодить задам кучу вопросов здесь.
1. дорма ес 200 и дорма ес 200 изи ошибки одинаковые? т.е одинаковые показания индикатора на ошибки?
2.если аккум древний и его пришлось откинуть надо ли это прописывать в параметрах? т.е тупо откинул аккум исправная дверь будет работать ? или ошибку выдаст?
3, если отключить радары и барьеры (физически) дверь будет обучаться?
короче пляска такая: дорма ес 200. не работает. не открывается не закрывается, на переключатель режимов никак не реагирует. скидываю питание в надежде скинуть ошибки обучить и вуаля…не прокатывает. дверь живет своей жизнью. индикатор не показывает нормального обучения(сегменты по кругу не бегут.створки полуоткрыты кнопка нажата(сервис)).створки стоят. курю. минут через пять створки оживают.даже как то реагируют нак радар. но….открываются сантиметров на 30 всего и встают. закрываю переключателем-закрываются.открываю переключателем-открываются , но опять сантиметров на 30. и глюк…ни туда ни сюда. на роликах створки катаются свободно, т.е на ощупь ничего не чувствую(заедания и т.п). да……при открытии выскакивает ошибка.и контроллер хоть убей не показывает номер ошибки.все показания индикатора сводятся либо к ошибке (Е) либо нормальная работа (точка).ни селект ни сервис кнопка не выводят меня в список ошибок. что делать ??выручайте
-
#36
Промой спиртом оптоглазок на энкодере…
-
#37
Промой спиртом оптоглазок на энкодере…
как до него добраться? вроде двигатель не разборный? ( я конечно под микроскопом его не рассматривал…может и ошибаюсь) тоже мысли про энкодер были. тут вот в чем дело ,когда створки открываются такою ощущение что они чем то тормозятся, прям почти упираются. скинул ремень створки нормально катаются. мысли про механику движка. что там (я не знаю, то ли подшипник то ли втулка на валу..) типа рассыпался и клинит. расскажи как до энкодера добраться…хотя бы на пальцах.
-
#38
У меня стоят 400 сотые, там круглая пластинка прозрачная с темными рисками прямо на виду….
-
Bookmarks
Quick Links
ES 200
—
Sliding door operator
Related Manuals for Dorma ES 200
Summary of Contents for Dorma ES 200
-
Page 1
ES 200 — Sliding door operator… -
Page 2
Delivery formats for the implementation of new Particularly impressive is the application on the basis of just The ES 200 is available as a prefabricated MiniDriveUnit, ideas and individual concepts in a few components. The system component kit, as a complete,… -
Page 3
24 V output for external accessory Opening and closing force, max. 150 N Read-out error memory with error codes Opening speed bus interface (Protokoll DORMA Connect and Work) 10 – 70 cm/s ® (incremental setting) Rechargeable battery pack for emergency operation Closing speed 10 –… -
Page 4
ES 200 SLIDING DOOR OPERATOR Pulley with integrated locking device and belt tensioning device Profiles for corridor installation, 100 mm Profiles for wall installation, 100 mm Our profiles for installation heights of 100 mm and 150 mm, which are suitable for both… -
Page 5
ES 200 SLIDING DOOR OPERATOR MiniDriveUnit At the core of the ES 200 Components The prefabricated MiniDriveUnit 1 MiniDriveUnit 10 Pulley (locking device) has been industrially tested with 2 Power supply unit 11 Service cover bracket all the requisite electrical and… -
Page 6
ES 200 SLIDING DOOR OPERATOR THE PROFESSIONAL OPERATOR FOR INDIVIDUAL DOOR DESIGN — Door variants with ES 200, 100 mm installation height and special ”profile“ version DORMA PowerDrive System for particularly punchy performance The door variants on this page are shown as corridor installation with aluminium girder (LM). -
Page 7
* Safety sensors to monitor the secondary closing edges in accordance with DIN 18650 and EN 16005 **Safety sensors to monitor the main closing edge in accordance with DIN 18650 and EN 16005 PROGRAM SWITCHES — A program switch from DORMA’s The corresponding 3-position They offer various options, from Up to 5 different functions:… -
Page 8: Push Button
ES 200 SYSTEM ACCESSORIES SWITCHES — Designation Specification Installation system Order No. On/Off switch White, aluminium, flush-mounting, 80 x 80 mm Gira S-Color 19135403150 Radar switch „MAGIC SWITCH”, proximity-type radar switch responds to movement, for flush-mounting, 80 x 80 mm…
-
Page 9
ES 200 SYSTEM ACCESSORIES EMERGENCY PUSHBUTTONS — Designation Specification Installation system Order No. Designed to interrupt the automatic movement of the door, emergency pushbutton (function: Emergency Off) for automatic door operators, manufactured to ZH 1/494 or BGR 232, DIN 18650 and EN 16005, red knob with yellow centre insert, max. -
Page 10: Motion Detectors
ES 200 SYSTEM ACCESSORIES MOTION DETECTORS — Motion detectors Designation Specification Colour Order No. Prosecure Full-automatic access on pulse activation; Easy Motion adjustable inclination angle, Mono inclined field of view and field size, LED status indicator, not in accordance black…
-
Page 11
ES 200 SYSTEM ACCESSORIES TRIMS AND BOXES FOR SURFACE-MOUNTED PUSHBUTTONS AND SWITCHES — Dimensions Designation Specification Installation system Order No. in mm (W x H x D) System 55 Cover frame (Programm STA) FR-S55 1 Single-type trim, Standard 55, white 80.7 x 80.7 System 55… -
Page 12
DORMA Deutschland GmbH DORMA Platz 1 58256 ENNEPETAL GERMANY Phone +49 2333 793-0 +49 2333 793-4950 www.dorma.com…
-
Bookmarks
Quick Links
ES 200
—
Sliding door operator
Related Manuals for Dorma ES 200
Summary of Contents for Dorma ES 200
-
Page 1
ES 200 — Sliding door operator… -
Page 2
Delivery formats for the implementation of new Particularly impressive is the application on the basis of just The ES 200 is available as a prefabricated MiniDriveUnit, ideas and individual concepts in a few components. The system component kit, as a complete,… -
Page 3
24 V output for external accessory Opening and closing force, max. 150 N Read-out error memory with error codes Opening speed bus interface (Protokoll DORMA Connect and Work) 10 – 70 cm/s ® (incremental setting) Rechargeable battery pack for emergency operation Closing speed 10 –… -
Page 4
ES 200 SLIDING DOOR OPERATOR Pulley with integrated locking device and belt tensioning device Profiles for corridor installation, 100 mm Profiles for wall installation, 100 mm Our profiles for installation heights of 100 mm and 150 mm, which are suitable for both… -
Page 5
ES 200 SLIDING DOOR OPERATOR MiniDriveUnit At the core of the ES 200 Components The prefabricated MiniDriveUnit 1 MiniDriveUnit 10 Pulley (locking device) has been industrially tested with 2 Power supply unit 11 Service cover bracket all the requisite electrical and… -
Page 6
ES 200 SLIDING DOOR OPERATOR THE PROFESSIONAL OPERATOR FOR INDIVIDUAL DOOR DESIGN — Door variants with ES 200, 100 mm installation height and special ”profile“ version DORMA PowerDrive System for particularly punchy performance The door variants on this page are shown as corridor installation with aluminium girder (LM). -
Page 7
* Safety sensors to monitor the secondary closing edges in accordance with DIN 18650 and EN 16005 **Safety sensors to monitor the main closing edge in accordance with DIN 18650 and EN 16005 PROGRAM SWITCHES — A program switch from DORMA’s The corresponding 3-position They offer various options, from Up to 5 different functions:… -
Page 8: Push Button
ES 200 SYSTEM ACCESSORIES SWITCHES — Designation Specification Installation system Order No. On/Off switch White, aluminium, flush-mounting, 80 x 80 mm Gira S-Color 19135403150 Radar switch „MAGIC SWITCH”, proximity-type radar switch responds to movement, for flush-mounting, 80 x 80 mm…
-
Page 9
ES 200 SYSTEM ACCESSORIES EMERGENCY PUSHBUTTONS — Designation Specification Installation system Order No. Designed to interrupt the automatic movement of the door, emergency pushbutton (function: Emergency Off) for automatic door operators, manufactured to ZH 1/494 or BGR 232, DIN 18650 and EN 16005, red knob with yellow centre insert, max. -
Page 10: Motion Detectors
ES 200 SYSTEM ACCESSORIES MOTION DETECTORS — Motion detectors Designation Specification Colour Order No. Prosecure Full-automatic access on pulse activation; Easy Motion adjustable inclination angle, Mono inclined field of view and field size, LED status indicator, not in accordance black…
-
Page 11
ES 200 SYSTEM ACCESSORIES TRIMS AND BOXES FOR SURFACE-MOUNTED PUSHBUTTONS AND SWITCHES — Dimensions Designation Specification Installation system Order No. in mm (W x H x D) System 55 Cover frame (Programm STA) FR-S55 1 Single-type trim, Standard 55, white 80.7 x 80.7 System 55… -
Page 12
DORMA Deutschland GmbH DORMA Platz 1 58256 ENNEPETAL GERMANY Phone +49 2333 793-0 +49 2333 793-4950 www.dorma.com…
ED100 / ED250
—
Error message memory
There are ten error message memory locations, «E0» through
«E9».
To access error messages, briefly press
messages contained in E0 to E9 memory.
Latest error message is always stored in error message memory
«E0».
As soon as another error occurs, or after existing «E0» error
has been reset, the former «latest» error in «E0» will be moved
to error message memory location «E1».
A maximum of nine errors can therefore be stored in «E1»
through «E9» memory locations. Identical error messages
which occur one after the other are not saved again.
Example:
If error E 15 occurs, and it is the first error, it will be stored in
the current (latest) error memory location «E0».
By briefly press
, the first error to be displayed will be E 15.
If a second error occurs before first error has been «Reset «
(11.3):
E 04 has occured, as an example.
E 15 will be moved to error memory location «E1», and E 04
will be stored in current (latest) memory location «E0».
By briefly pressing
to call up error messages memory
locations E0, the first message to be displayed will be
E 04 (the latest error), briefly pressing
the next message, E 15.
A maximum of nine errors can therefore be saved in E1 – E9
error memories.
E 15
E0
E0
E 15
E1
E1
E2
E2
E3
E3
E4
E4
E5
E5
E6
E6
E7
E7
E8
E8
E9
E9
DORMA AUTOMATICES, Inc.
34
DL3463-050
08/2016
SERVICE MANUAL
to display error
again will display
E 04
E 71
E0
E 04
E0
E 71
E1
E 15
E1
E 04
E2
E2
E 15
E3
E3
E4
E4
E5
E5
E6
E6
E7
E7
E8
E8
E9
E9
924 Sherwood Drive
Toll-Free: 877-367-6211
Lake Bluff, IL 60044
Fax:
Operator unit LED status
ƒ
Green LED
ON – Indicates internal 24VDC power on.
OFF – Indicates internal 24VDC power off.
Yellow LED
ƒ
Maintenance interval indicator. When illuminated, it is an
indication that operator system should be serviced.
Maintenance interval is adjustable by DORMA service.
Red LED
ƒ
Blinking codes are used to indicate «ln __» information or
certain error codes «E __».
Details on each display code, or LED status, can be found in
the troubleshooting chart starting on the next page.
Red LED status User interface
display
Steady flashing
On steady
ln 11
Flashing 2 times E 02
Flashing 4 times E 04
Flashing 5 times E 25
Flashing 5 times E 51, E 52, E 53
Flashing 6 times E 62
Flashing 6 times E 63
Flashing 7 times E 71
Flashing 7 times E 72
Flashing 7 times E 73
Flashing 12 times E 12
Flashing 13 times E 13
Flashing 15 times E 15
Subject to change without notice
847-249-3999
Description
Control unit has detected
error – Emergency mode
has been activated
Hold-open device was
triggered
Locking device error
Safety sensor test error
SVP Power Reserve
(PR) DCW module test
negative
Incremental encoder
error
Second system has
firmware version
incompatible with double
door system operation
Second system has
incompatible fire
protection setting
System error 1 (test)
second shutdown option
System error 2 (test)
current measuring circuit
System error 3 (test)
braking circuit
EEPROM error
Motor overcurrent
Fautly learning cycle