Cyflex f900 ошибки

Аватара пользователя

Алекс югм

Сообщения: 3
Зарегистрирован: 16 авг 2022 12:52

Cyflex f900 ошибка после калибровки оси Z

Сообщение

Алекс югм »

Всем доброго дня, после ошибки смазки (PLC74) станок перестал выполнять калибровку по оси X и Y, в момент запуска калибровки станок по оси Z наезжает на калибровочную пятку, затем начинает движение в противоположном направлении и выходит ошибка PLC41 Аварийная остановка станка, с его отключением. После перезапуска через кнопку F10 станок снова запускается и при выполнении калибровки выходит таже ошибка. Концевики проверели по всем осям, все звонятся. Кто то сталкивался с такой проблемой?
P.S. ошибку смазки PLC74 устранили перезапуском смазки вручную.

Аватара пользователя

demonlibra

Администратор
Сообщения: 7481
Зарегистрирован: 11 сен 2008 08:20
Благодарил (а): 23 раза
Поблагодарили: 107 раз

Cyflex f900 ошибка после калибровки оси Z

#2

Сообщение

demonlibra »

Может быть чем-то поможет. В инструкции нашёл такие строки.

ПРИЧИНЫ: Выход осей за границы рабочего диапазона.
ПОРЯДОК ДЕЙСТВИЙ: Управляя осями вручную, переместить их в границы рабочего диапазона.

Координаты оси отображаются адекватные?

Не бойся поломать. Бойся не починить ))
Изображение

Аватара пользователя

oleg 39

Опытный
Опытный
Сообщения: 322
Зарегистрирован: 03 сен 2010 19:31
Благодарил (а): 1 раз
Поблагодарили: 11 раз

Cyflex f900 ошибка после калибровки оси Z

#3

Сообщение

oleg 39 »

На Ровере была такая проблема. У оси z такая особенность, что при не срабатывании аварийного концевика, он упирается в механический буфер (обрезиненный ограничитель) и едет в обратную сторону. Как временное решение, программно ограничили диапазон оси. Но нет ничего более постоянного, чем временное решение.

Аватара пользователя

Алекс югм

Сообщения: 3
Зарегистрирован: 16 авг 2022 12:52

Cyflex f900 ошибка после калибровки оси Z

#4

Сообщение

Алекс югм »

demonlibra писал(а): ↑16 авг 2022 13:20
Может быть чем-то поможет. В инструкции нашёл такие строки.

ПРИЧИНЫ: Выход осей за границы рабочего диапазона.
ПОРЯДОК ДЕЙСТВИЙ: Управляя осями вручную, переместить их в границы рабочего диапазона.

Координаты оси отображаются адекватные?

Координаты не адекватные, станок находится не в 0 точках, а по программе показывает что 0, но при наезде оси Z на калюбровочную пятку (в програме показывает ось Z допусим -35) в программе происходит сброс и отображается 0, дальше такое же должно произойти и с другими осями, X, Y, но станок уходит в аварию PLC41. Ещё одно удивление, что в ручном режиме все работает адекватно, но как только запускается калибровка и станок выходит на 0 по оси Z происходит его аварийное отключение. Заказали концевик новый, возможно в нем проблема. Пока проблема не решена

Аватара пользователя

demonlibra

Администратор
Сообщения: 7481
Зарегистрирован: 11 сен 2008 08:20
Благодарил (а): 23 раза
Поблагодарили: 107 раз

Cyflex f900 ошибка после калибровки оси Z

#5

Сообщение

demonlibra »

Сомневаюсь, что дело в концевике.
Похоже, что управляющее напряжение отключает ЧПУ. Вопрос, почему.
Скудность аварийных сообщений не позволяет это определить.

Гляньте на сервопривод оси Z. Может на нём, что-то отображается интересное во время калибровки.

Не бойся поломать. Бойся не починить ))
Изображение

Аватара пользователя

Алекс югм

Сообщения: 3
Зарегистрирован: 16 авг 2022 12:52

Cyflex f900 ошибка после калибровки оси Z

#7

Сообщение

Алекс югм »

oleg 39 писал(а): ↑19 авг 2022 09:09
А вообще в SCM такие элементы и понятия, как калибровочный концевик, микромаркер, аварийный концевик присутствуют? Если да, то и действия со станками н-р от Biesse будут аналогичными.

На каждой оси установлено по 2 концевика, один калибровочный, второй аварийный. После наезда калибровочным концевиком на пятку (размыкание концевика) и возврату в обратном направлении (замыкание концевика) станок выключается, будто бы наехал на аварийный концевик, хотя ни на один аварийный концевик не наезжал.
Сегодня смотрели работу сервоприводов, ошибок никаких нет… надежда что глючит концевик…

Аватара пользователя

oleg 39

Опытный
Опытный
Сообщения: 322
Зарегистрирован: 03 сен 2010 19:31
Благодарил (а): 1 раз
Поблагодарили: 11 раз

Cyflex f900 ошибка после калибровки оси Z

#8

Сообщение

oleg 39 »

Алекс югм писал(а): ↑20 авг 2022 16:03
На каждой оси установлено по 2 концевика, один калибровочный, второй аварийный. После наезда калибровочным концевиком на пятку (размыкание концевика) и возврату в обратном направлении (замыкание концевика) станок выключается, будто бы наехал на аварийный концевик, хотя ни на один аварийный концевик не наезжал.

Точно аварийный один? По логике должно быть два. У нас на Ровере 20 на оси Y тоже был случай. Когда наладчик снимал датчик, он то ли не обратил внимание, то ли забыл, что тот крепился к корпусу через шайбы, довольно толстые. В результате концевик наезжал на «чужие» пятки и проблема была схожей с Вашей. https://disk.yandex.ru/i/D3RBf4VQKyif7g

  1. 11-23-2017, 08:43 PM


    #1

    Join Date
    Nov 2017
    Posts
    1

    SCM Cyflex F900. Error cnc 1126 error calibration

    Hi. There is a problem with calibration Cyflex wholesale-f900. When you start calibration, stop and write an error: NC 1126 Z calibration error. This happens after the endstop on Z off. It is not a mechanical or electrical. I checked. The guy who worked wrote texts about absolutely zero. He changed absolutely zero in the cnc parameters. Please help me. Maybe some one know or have a manual for xilog plus after input password


FORUM GUIDELINES: Please review the guidelines below before posting at WOODWEB’s Interactive Message Boards (return to top)

  • WOODWEB is a professional industrial woodworking site. Hobbyist and homeowner woodworking questions are inappropriate.
  • Messages should be kept reasonably short and on topic, relating to the focus of the forum. Responses should relate to the original question.
  • A valid email return address must be included with each message.
  • Advertising is inappropriate. The only exceptions are the Classified Ads Exchange, Machinery Exchange, Lumber Exchange, and Job Opportunities and Services Exchange. When posting listings in these areas, review the posting instructions carefully.
  • Subject lines may be edited for length and clarity.
  • «Cross posting» is not permitted. Choose the best forum for your question, and post your question at one forum only.
  • Messages requesting private responses will be removed — Forums are designed to provide information and assistance for all of our visitors. Private response requests are appropriate at WOODWEB’s Exchanges and Job Opportunities and Services.
  • Messages that accuse businesses or individuals of alleged negative actions or behavior are inappropriate since WOODWEB is unable to verify or substantiate the claims.
  • Posts with the intent of soliciting answers to surveys are not appropriate. Contact WOODWEB for more information on initiating a survey.
  • Excessive forum participation by an individual upsets the balance of a healthy forum atmosphere. Individuals who excessively post responses containing marginal content will be considered repeat forum abusers.
  • Responses that initiate or support inappropriate and off-topic discussion of general politics detract from the professional woodworking focus of WOODWEB, and will be removed.
  • Participants are encouraged to use their real name when posting. Intentionally using another persons name is prohibited, and posts of this nature will be removed at WOODWEB’s discretion.
  • Comments, questions, or criticisms regarding Forum policies should be directed to WOODWEB’s Systems Administrator
    (return to top).

    Carefully review your message before clicking on the «Send Message» button — you will not be able to revise the message once it has been sent.

    You will be notified of responses to the message(s) you posted via email. Be sure to enter your email address correctly.

    WOODWEB’s forums are a highly regarded resource for professional woodworkers. Messages and responses that are crafted in a professional and civil manner strengthen this resource. Messages that do not reflect a professional tone reduce the value of our forums.

    Messages are inappropriate when their content: is deemed libelous in nature or is based on rumor, fails to meet basic standards of decorum, contains blatant advertising or inappropriate emphasis on self promotion (return to top).

    Libel:   Posts which defame an individual or organization, or employ a tone which can be viewed as malicious in nature. Words, pictures, or cartoons which expose a person or organization to public hatred, shame, disgrace, or ridicule, or induce an ill opinion of a person or organization, are libelous.

    Improper Decorum:   Posts which are profane, inciting, disrespectful or uncivil in tone, or maliciously worded. This also includes the venting of unsubstantiated opinions. Such messages do little to illuminate a given topic, and often have the opposite effect. Constructive criticism is acceptable (return to top).

    Advertising:   The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you’re in, your URL and email address (return to top).

    Repeated Forum Abuse:
    Forum participants who repeatedly fail to follow WOODWEB’s Forum Guidelines may encounter difficulty when attempting to post messages.

    There are often situations when the original message asks for opinions: «What is the best widget for my type of shop?». To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB’s experience that substantive responses are held in higher regard by our readers (return to top).

    The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB’s Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB’s Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)

  • Морозов Павел

    svik-spb

    Присоединяйтесь к обсуждению

    Вы можете написать сейчас и зарегистрироваться позже.

    Если у вас есть аккаунт, авторизуйтесь, чтобы опубликовать от имени своего аккаунта.

    • #1

    Hello, we’ve had trouble with lubrication errors and service personnel had to remove belt from Y axis and manually (by hand) rotate ballscrew and after returning belt the Y axis was no longer correct, meaning when you have to drill a hole in Y10. coordinate it would drill it in Y19. How do you fix this problem in machine parameters or somehow without removing belt again and trying to get the ballscrew back to it’s original position?

    Понравилась статья? Поделить с друзьями:

    Интересное по теме:

  • Cz rd513c сброс ошибки
  • Cyberpunk 2077 ошибка при запуске игра прекратила работу
  • Cz rd513c коды ошибок
  • Cyberpunk 2077 ошибка при запуске assert
  • Cypcut ошибка servo alarm

  • 0 0 голоса
    Рейтинг статьи
    Подписаться
    Уведомить о
    guest

    0 комментариев
    Старые
    Новые Популярные
    Межтекстовые Отзывы
    Посмотреть все комментарии