Cyberpower cps600e коды ошибок

CPS600E

1.

Overheat Protection: The EPS output will be interrupted. After 30 seconds, the machine shuts

down and the LCD display output voltage is zero.

Over-Load Protection： ： ： ： The EPS output will be interrupted. After 30 seconds, the machine shuts

2.

down and Over Load Icon lights on the LCD display.

Battery Missing： ： ： ： You should hear a long beep and Battery Indicator flashes。

3.

4.

Low Battery Protection: The EPS output will be interrupted. After 30 seconds, the machine shuts

down and the LCD display output voltage is zero.

5.

The following table shows each corresponding warning message on the LCD display and the alarm

reacts during the machine shut down：

LCD

Warning

Display

Over Load Icon

Zero Output

Voltage

Can Not Start Up

Copyright © 2010 CyberPower Systems, Inc.

Alarm

Over Load Output-Off — Load

Constant tone

exceed the rating of EPS.

High Temperature Output-Off

Low Battery Output-Off

— Insufficient battery capacity.

Over Charge or AVR Error—

Constant tone

In Line Mode, battery is

overcharged or AVR is faulty.

Short Output-Off — Output

Short Circuit Protection

Line

Output-Off — incorrect Input/

Output connection

None

Cold

Voltage

battery voltage is too high

during cold start.

Condition

Input/

Output

Error

Start

Battery

High

Output-Off

—

the

Solution

Check

total

load

to

confirm the rating of

EPS.

Check fans function and

air vent clearances.

Recharge the battery.

Inform service agents.

Check the EPS output

to see if there is a short

circuit.

Check

Input/

Output

connection.

Check the reason for

battery over-voltage.

10

• Contents

• Table of Contents

• Troubleshooting

• Bookmarks

Summary of Contents for CyberPower CPS600E

• 2, 2 SAFETY AND EMC INSTRUCTIONS This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or operate your Emergency Power System (EPS). CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity control…

• 3, 3 EMS: IEC/EN61000-4-2(ESD) IEC/EN61000-4-3(RS) IEC/EN61000-4-4(EFT) IEC/EN61000-4-5(lightning surge) IEC/EN61000-2-2 (Immunity to low frequency signals) INSTALLING YOUR EPS UNPACKING Inspect the EPS upon receipt. The box should contain the following: (1) EPS Unit x 1; (2) User Manual x 1; (3) Input Power Cord x 1; (4) DC Fuse x 2 AUTOMATIC VOLTAGE REGULATOR Utility power is inconsistent. The EPS increases low voltage to comp…

• 4, CyberPower CPS600E-IN 4 BASIC OPERATION DESCRIPTION 1. Power Switch Used as the master on/off switch for equipment connected to the AC outlet. 2. Power On Indicator This LED is above the power switch. It illuminates when the utility condition is normal and the AC outlet is providing power, free of surges and spikes. 3. Multifunction LCD Readout High resolution and intelligent LCD display shows all the EPS information with icons and mes…

• 5, 5 REPLACING THE BATTERY CAUTION! Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery. Battery service should only be done by qualified professionals. CAUTION! Use only the specified type and number of external batteries. Please see the technical specifications for replacement batteries. CAUTION! The battery may present a risk of electrical shock. Do not dispose of battery in a fire as it ma…

• 6, 6 5. SILENT MODE Icon: This icon appearing indicates that the buzzer does not beep in the silent mode until the low battery capacity. 6. OVER LOAD Icon: This icon appearing and an alarm activated indicate that the overload condition. To relieve the overload, unplug your equipment from the EPS outlets until the icon disappears and the alarm stops being activated. 7. LOAD CAPACITY: Load CAPACITY is also show…

• 7, 7 d. Static Frequency Tolerance: There are 6 settings (1,2,4,6,8,10%), and the default setting is +/-6%. Function description: The settings may be adjusted to the quality of the electricity in use. e. Slew Rate: Also called Dynamic Frequency Tolerance. There are 5 different settings (0.25,0.5,1,2,4 Hz/Sec). The default value is 4Hz/sec. Function description: “Slew Rate” indicates the tolerance of a device in accepting frequency variances. The lower “Slew Rate” results in l…

• 8, 8 4. Low Battery Protection: The EPS output will be interrupted. After 30 seconds, the machine shuts down and the LCD display output voltage is zero. 5. The following table shows each corresponding warning message on the LCD display and the alarm reacts during the machine shut down ： LCD Warning Display Alarm Condition Solution Over Load Icon Constant tone Over Load Output-Off — Load exceed the rating of EPS. Check total load to confirm the rating of EPS. Zero Ou…

• 9, 9 TROUBLESHOOTING Problem Possible Cause Solution Outlet does not provide power to equipment. Input fuse is blown due to overload. Turn the EPS off and unplug the connected equipment. Unplug the power cord of the EPS then remove the fuse compartment beneath the AC inlet of the EPS and replace the blown fuse with a spare one. Lock the compartment back to the EPS. Connect power cord then turn the EPS on. Make sure that your spare fuse meets the specification and the equip…

• 10, 10 TECHNICAL SPECIFICATIONS Model CPS600E-IN Capacity (VA) 600VA Capacity (Watts) 420W Operation Technology AVR ( Single Boost & Single Buck ) AC Input Input Voltage Range 170Vac – 270Vac Input Frequency Range 50 / 60 Hz +/- 5Hz AC Output Number of Phase Single Phase On Battery Typical Output Voltage 0 ~40% LOAD Pure Sine Wave at 230Vac +/- 5 % 40~100% LOAD Trapezoidal Wave at 230Vac…