C0711 ошибка тахо

What does DTC code c0711 mean on Chevy Tahoe?

C0711 Level Control Air Pressure Sensor Circuit Malfunction This DTC Code indicates either the Automatic Level Control pressure sensor has failed, or more commonly, the wiring for the sensor has been shorted to ground, often due to a pinched or broken wire from replacing the air suspension compressor.

Where is the suspension sticker on a Chevy Tahoe?

This sticker is always found on the inside of the glove box door. You can see the codes are in numerical order and that this vehicle came equipped with the Z55 Autoride suspension. 1. Convert the vehicle to a conventional high-end monotube shock suspension with shocks and springs.

When was the last time I serviced my Chevy Tahoe?

Last serviced at 138,668 miles in Sugar Land, TX on 06/04/21 • Vehicle serviced • Tire condition and pressure checked • Nitrogen fill tires • Oil and filter changed • Emissions inspection performed. No accident or damage reported to CARFAX. Purchased on 02/13/12 and owned in CA until 05/14/21. Driven an estimated 7,977 miles/year.

How many miles does a 2012 Chevy Tahoe drive?

1st owner purchased on 11/23/12 and owned in IN until 04/11/19 • 2nd owner purchased on 04/20/19 and owned in IN until 04/20/21. 1st owner drove an estimated 27,266 miles/year • 2nd owner drove an estimated 7,725 miles/year.

C0711 Level Control Air Pressure Sensor Circuit Malfunction This DTC Code indicates either the Automatic Level Control pressure sensor has failed, or more commonly, the wiring for the sensor has been shorted to ground, often due to a pinched or broken wire from replacing the air suspension compressor.

What happens when the Ride Control Relay goes bad?

The Electronic Control System disables the compressor motor relay when this code is thrown, and may cause you to think the Ride Control Relay has gone bad. Check the IGN 3 fuse or replace you air suspension compressor.

This sticker is always found on the inside of the glove box door. You can see the codes are in numerical order and that this vehicle came equipped with the Z55 Autoride suspension. 1. Convert the vehicle to a conventional high-end monotube shock suspension with shocks and springs.

Why is the clicking on my Chevy Tahoe not working?

The clicking is usually a solenoid (when battery voltage is strong enough, it holds the solenoid down to supply starter with full voltage.) So, Battery may be old, or damaged or out of water, it needs to be checked with a hydrometer or battery tester (each individual cell).

The Electronic Control System disables the compressor motor relay when this code is thrown, and may cause you to think the Ride Control Relay has gone bad. Check the IGN 3 fuse or replace you air suspension compressor.

Where is the fuse on a Chevy Tahoe?

He ran that cable to the same point as the battery cable that feeds the 175 amp 32 volt fuse. On the other side of the fuse he left the cable that connects to the fuse box inside the engine compartment.

What does trouble code U1000 mean on a Chevy?

This is a manufacturer specific network code. Specific troubleshooting steps will vary depending on the vehicle. The trouble code U1000 is a vehicle specific code primarily found on Chevrolet, GMC and Nissan vehicles. It refers to a “Class 2 communications failure.”

What is the OBD2 code for a Chevy?

OBDII Chevrolet Code Definitions. Be sure to double check the codes. Anything P1000 to P1999 or P3000 to P3400 will be Manufacturer specific and may not match the ones listed here. Check specific manufacturer pages on the site, as some of them, we list the OBD2 codes on those pages for those specific vehicles.

What kind of truck is Chevy Silverado Z71?

It’s a pickup truck designed for off-road and all-terrain roads. Roads that deny you comfort while you’re driving. It is one of the Silverado lineup trucks. The only difference is that it comes equipped with the z71, a package with extra features that turns it into an off-road machine. So, what does the z71 package entail?

This is a manufacturer specific network code. Specific troubleshooting steps will vary depending on the vehicle. The trouble code U1000 is a vehicle specific code primarily found on Chevrolet, GMC and Nissan vehicles. It refers to a “Class 2 communications failure.”

What happens if I get a B1000 DTC and no other?

The Code reader shows only one code, and it’s B1000 which is ECU malfunction 2, according to my code reader. If you try and erase the code it says it is successful, but upon re-link it comes back. I already had myairbags.com reprogram the airbag module and get the same B1000 code.

OBDII Chevrolet Code Definitions. Be sure to double check the codes. Anything P1000 to P1999 or P3000 to P3400 will be Manufacturer specific and may not match the ones listed here. Check specific manufacturer pages on the site, as some of them, we list the OBD2 codes on those pages for those specific vehicles.

What happens if I get a B1000 code error?

I already had myairbags.com reprogram the airbag module and get the same B1000 code. If I unplug any other sensors to the system then I get a code error for each of them. They disappear when the sensors are reconnected. I have no idea which component is causing the error.

Where are the DTC codes on a Cadillac Escalade?

These four DTC Codes indicate a height sensor issue, which are located near each wheel, behind the fender and attached to the control arms in the suspension. Each sensor is a rod connected to a small ball joint, and each sensor can be freed from the joint and tested separately.