Bk150fueh коды ошибок - TopOshibok.ru - решение и исправление самых разных ошибок

BK150FUEH ошибка F915
Случилась после аварии на линии 10 киловольт питания завода с миганием ламп и просадкой напряжения на одной из фаз (оборвался провод и была дуга)
Ворота V5015SE.
В инструкции такой ошибки нет. Что значит эта ошибка?

-=BVS=-

Квалифицированный специалист

Обратитесь к Станиславу https://www.vorotaforum.ru/members/487/ так или иначе вам всё равно предстоит общение с Hormann

У меня нет доступа к его профилю по этой ссылке?…. А его почту, когда он мне помогал сменить прошивку на именно этом блоке управления в 2010 году, что-то пока не найду…

Позвонить или написать в сервис представительства Херман никак?

Позвонить или написать в сервис представительства Херман никак?

Это ты умничаешь что-ли??? Звонок в сервис это само-собой разумеется, никто и не спорит. Уже написали и позвонили. В моем случае F915 означает замену блока управления, сервис тебе здесь только в отдел продаж перенаправит. Вот и вся его помощь.
А на форуме порой бывают альтернативные решения….

Это ты умничаешь что-ли???

Это ты типа выебнулся что-ли???
Так вот хуй тебе, а не альтернативное решение…

Это ты умничаешь что-ли???

я самый верный способ решения проблемы предлагаю

сервис тебе здесь только в отдел продаж перенаправит.

меня не направит

А на форуме порой бывают альтернативные решения….

Так вот хуй тебе, а не альтернативное решение…

согласен

kalitki

Квалифицированный специалист

У меня нет доступа к его профилю по этой ссылке?.

У меня почему-то тоже ошибка…

Ты сам себе злобный Буратино…

Dizelc

Квалифицированный специалист

Это ты умничаешь что-ли???

Очень тактично. Вперед эрудировать.

я самый верный способ решения проблемы предлагаю

Самый верный и … самый дорогой… И как я писал, он был проделан в первую очередь.
Извини, если я резко отреагировал, на твое «позвонить никак?» От эксперта не ожидаешь банальных ответов, хочется , что-нибудь экспертное… В общем, спасибо ребята, вы мне очень помогли

Dizelc

Квалифицированный специалист

От эксперта не ожидаешь банальных ответов

И много у Вас знаком экспертов которые очень щепетильно помогают Вам и чутко реагируют на Ваши запросы. При этом бескорыстно.

привет
У меня такая же проблема. BK150FUEH ошибка F915. Вы нашли решение? Вы можете мне помочь?

Это внутренняя ошибка, связанная с питанием или с коммуникацией процессора в приводе, своими силами такое не ремонтируется, надо было посылать в ремонт, а там видимо была бы просто замена платы или еще муторнее… Просто выкинули и купили новый. Причем Hoermann отказался продавать такой же или его новую версию FUE-1, т.к. изначально там стоял вообще еще контакторный TST WU и предложили купить плату AKE еще под старый корпус, который мы уже выкинули… вообщем… после 2-х месяцев переписки плюнули и купили стандартную модель у производителя этих контроллеров www.feig.de. Пришлось конечно повозиться с настройками (разряжались батарейки при заблокированных воротах) и потерять кучу времени, но в итоге все работает. Сервис в Германии отвечает на вопросы по e-mail, предоставили самую полное описание всех параметров и документацию. Но это путь для гиков, была бы возможность мы бы просто купили бы новый.

Dizelc

Квалифицированный специалист

Ну вот вам и херман. Где те самые ценители сервиса Херман. Человек пишет сроки 2 месяца переписок. Капец.

Dizelc

Квалифицированный специалист

Это внутренняя ошибка, связанная с питанием или с коммуникацией процессора в приводе, своими силами такое не ремонтируется

Ну думаю все равно стоило чужими силами поднять плату.

Ну вот вам и херман. Где те самые ценители сервиса Херман. Человек пишет сроки 2 месяца переписок. Капец.

Ну я ценитель
А с остальными членами большой тройки лучше? Недавно тут только про Дорхан писали, хотя про него историй хватает всегда

Ну я ценитель
А с остальными членами большой тройки лучше? Недавно тут только про Дорхан писали, хотя про него историй хватает всегда

У всех есть косяки, только одних в ранг богов записывают с их окуенными косяками и покуизмом на пользователя, других, с косяками поменьше, в гомне безостановочно валяют.

Dizelc

Квалифицированный специалист

Недавно тут только про Дорхан писали, хотя про него историй хватает всегда

Уже про него писать нечего все карты раскрыты, причем похоже навсегда. А про Х только скажи, сразу да не может быть, сам дурак.

Не, Олексий, что значит, бывает… Ты как бывший хермановец поподробней расскажи о тайнах испан…хермановского двора. Нам будет интересно услышать и на ус намотать..

Источник

-=BVS=-

Квалифицированный специалист

Обратитесь к Станиславу https://www.vorotaforum.ru/members/487/ так или иначе вам всё равно предстоит общение с Hormann

Позвонить или написать в сервис представительства Херман никак?

Позвонить или написать в сервис представительства Херман никак?

Это ты умничаешь что-ли???

Это ты типа выебнулся что-ли???
Так вот хуй тебе, а не альтернативное решение…

Это ты умничаешь что-ли???

я самый верный способ решения проблемы предлагаю

сервис тебе здесь только в отдел продаж перенаправит.

меня не направит

А на форуме порой бывают альтернативные решения….

Так вот хуй тебе, а не альтернативное решение…

согласен

kalitki

Квалифицированный специалист

У меня нет доступа к его профилю по этой ссылке?.

У меня почему-то тоже ошибка…

Ты сам себе злобный Буратино…

Dizelc

Квалифицированный специалист

Это ты умничаешь что-ли???

Очень тактично. Вперед эрудировать.

я самый верный способ решения проблемы предлагаю

Dizelc

Квалифицированный специалист

От эксперта не ожидаешь банальных ответов

привет
У меня такая же проблема. BK150FUEH ошибка F915. Вы нашли решение? Вы можете мне помочь?

Dizelc

Квалифицированный специалист

Ну вот вам и херман. Где те самые ценители сервиса Херман. Человек пишет сроки 2 месяца переписок. Капец.

Dizelc

Квалифицированный специалист

Это внутренняя ошибка, связанная с питанием или с коммуникацией процессора в приводе, своими силами такое не ремонтируется

Ну думаю все равно стоило чужими силами поднять плату.

Ну вот вам и херман. Где те самые ценители сервиса Херман. Человек пишет сроки 2 месяца переписок. Капец.

Ну я ценитель
А с остальными членами большой тройки лучше? Недавно тут только про Дорхан писали, хотя про него историй хватает всегда

Dizelc

Квалифицированный специалист

Недавно тут только про Дорхан писали, хотя про него историй хватает всегда

Добрый день. У нас 3 блока BK150FUEH неисправных с ошибкой F915. Подскажите, пожалуйста, к кому можно обратиться по поводу ремонта?

Добрый день. У нас 3 блока BK150FUEH неисправных с ошибкой F915. Подскажите, пожалуйста, к кому можно обратиться по поводу ремонта?

Украина,Запорожье.Где вы находитесь?

Украина,Запорожье.Где вы находитесь?

Находимся в России г. Псков. С точки зрения сервиса, предпочтительнее, конечно, кого-то в Санкт-Петербурге найти.

Находимся в России г. Псков. С точки зрения сервиса, предпочтительнее, конечно, кого-то в Санкт-Петербурге найти.

Никого вы не найдете.Я очень долго сидел над проблемой,пока нашел решение.

Последнее редактирование модератором: 6 Авг 2022

Добрый день. В эксплуатации находится блок управления BK 150 FUE H. Присутствует ошибка F915.
Если на форуме есть специалисты кто готов взяться за ремонт, пусть даже за Дорого — Готовы посотрудничать.
Или кто может знает контакты людей к кому можно обратиться — прошу поделиться. Будем очень благодарны.

Добрый день. Я могу поремонтировать данные блоки. Справлялся с проблемой F915. Да и до Ульяновска не далеко). если кому интересно, пишите в личку или на почту ufs@bk.ru.

Добрый день. Я могу поремонтировать данные блоки. Справлялся с проблемой F915. Да и до Ульяновска не далеко). если кому интересно, пишите в личку или на почту ufs@bk.ru.

написал Вам на почту

Форумчане, привет!
Кто-нибудь берёт в ремонт данные блоки с ошибкой F915?

Вряд ли.
Прикрути б/у от шафта.

Форумчане, привет!
Кто-нибудь берёт в ремонт данные блоки с ошибкой F915?

Я ремонтирую. Пишите на почту ufs@bk.ru.

Я ремонтирую. Пишите на почту ufs@bk.ru.

Может с нами поделитесь рецептами ремонта, на форуме?

Может с нами поделитесь рецептами ремонта, на форуме?

Рецепт прост.Обкладываешься контрольно-измерительным инструментом,гуглишь интернет в поисках схем и мануалов,тратишь месяц-полтора жизни,получашь результат может быть,а потом ПРОСТО СЛИВАЕШЬ РЕШЕНИЕ ХАЛЯВЩИКАМ!!!

Рецепт прост.Обкладываешься контрольно-измерительным инструментом,гуглишь интернет в поисках схем и мануалов,тратишь месяц-полтора жизни,получашь результат может быть,а потом ПРОСТО СЛИВАЕШЬ РЕШЕНИЕ ХАЛЯВЩИКАМ!!!

Мы всем форумом этой …нёй уже больше 10 лет занимаемся. И Вы гляжу к нашему форуму присоединились…
Так что Ваш тон, с подъёбкой совершенно не уместен.

Все подсказки я дал еще год назад.Хороший электронщик разберется.Проблема комплексная.Решение у меня есть,оно стоит денег.Присылайте,отремонтируем.

Решение у меня есть,оно стоит денег.Присылайте,отремонтируем.

А вот реклама тут тоже платная…

Коллеги, добрый день. Форумчанин Evgeny_L справился с ремонтом нашего блока именно с ошибкой F915 блока BK150FUEH! Отправляли ему блок курьером на адрес и забирали от него курьером, сам ремонт занял всего несколько дней. Цена за работу, по сравнению со стоимостью нового блока, очень приемлемая. Настройки после ремонта не слетели. Оформляли все по договору и по безналу, что важно для нас как для организации. Очень рекомендую Evgeny_L !

Home
Инструкции
Автоматика для ворот
HORMANN
BK150FUEH

HORMANN Электронный блок управления HORMANN BK150FUEH инструкция по эксплуатации и монтажу на русском языке в формате pdf, размер файла 1.3 Mb. Используйте кнопки «Скачать инструкцию» или «Открыть в новом окне» (документ откроется в новом окне или вкладке браузера). Функция просмотра доступна при наличии плагина Adobe Acrobat в вашем браузере.

HORMANN BK150FUEH инструкция

Язык: Русский

Размер : 1.3 Mb

Формат файла: pdf

Добавлен: 22.06.2015

Руководство по установке и использованию

Предварительный просмотр

Информация, описание, технические характеристики изделия

Описание и информация о технических характеристиках по данному изделию пока что отсутствует. Содержание во всех разделах сайта периодически обновляется. Попробуйте зайти на страницу позже.

Отзывы по оборудованию и комментарии к материалу

Здесь можно оставить свои отзывы по оборудованию «HORMANN BK150FUEH — Блок управления», а также написать комментарии к материалу.

О компании
- Производство
  - Материалы
  - Контроль качества
- Лицензии / сертификаты
- Партнеры
- Статьи
- Вакансии
- Документы
  - Техническая документация
- Сотрудники
  - Отдел продаж
- Галерея
- Отзывы
- Видеогалерея
- Вопросы и ответы
Услуги и сервис
- Ремонт гаражных ворот
- Ремонт рольставней
- Ремонт откатных ворот
- Установка заборов
- Ремонт промышленных ворот
- Ремонт панорамных ворот
- Ремонт противопожарных ворот
- Ремонт штор противопожарных
- Ремонт автоматики
- Ремонт шлагбаумов
- Ремонт парковочных систем
- Ремонт скоростных ворот
- Ремонт перегрузки
- Доставка
- Монтаж
- Замер
- Постгарантийное обслуживание
Акции
- Рассрочка
- Ворота без предоплаты
- Комплект автоматики дешевле
- Ворота с автоматикой дешевле
- Ворота самовывоз -10%
- Окно в калитку в подарок
- Пульты в подарок
Инструкции
- Как выбрать
- Особенности
Запчасти
Отзывы
Портфолио
Контакты

Vorota Group

Ворота и рольставни в Москве и Московской области

Ворота — без предоплаты!
* стандартные размеры
Изготавливаем за 1 день
* стандартные размеры
Выезд на замер — бесплатно
* при заключении договора

Vorota Group

Ворота и рольставни в Москве и Московской области

/
Инструкции
/
Инструкция к автоматике

Как выбрать
Особенности

Как выбрать
Особенности

2002- 2023 © Vorota Group. Ворота и рольставни в Москве: продажа, монтаж и обслуживание

Выберите город

Москва и область
Вся Россия

Выберите город

Москва и область
Вся Россия

Источник

Home
Инструкции
Автоматика для ворот
HORMANN
BK150FUEH

HORMANN BK150FUEH инструкция
Тип инструкции:	Руководство по установке и использованию
Категория:	Автоматика для ворот HORMANN
Язык:	Русский
Размер:	1.3 Mb
Формат файла:	pdf
Дата добавления:	22.06.2015

Отзывы по оборудованию и комментарии к материалу

Ответить 26.06.2019 18:34

Денис

код ошибки F.030 Нужна принципиальная механическая схема. Спасибо.

Ответить 18.09.2019 09:45

Алексей

Код F.7A2 из-за чего?

Ответить 07.10.2019 12:52

Валера

Ошибка е. 108???

Ответить 30.12.2019 14:27

иван

Код ошибки F060 это что?

Ответить 10.01.2020 11:35

Николай

Была ошибка f926 ее нет в каталоге, щас блок вырубился,220 приходит, моргает красный светодиод на плате, что делать?

Ответить 28.02.2020 13:38

Роман

Где взять пароль для входа в расширенное меню

Ответить 10.09.2020 08:27

Александр

E883

Ответить 12.11.2020 06:59

Алексей

Ошибка Е.108 при том что на 54 контакте ничего не подключено (вход 8), и предконцевых выключателей нет. В ручном режиме работают в автоматическом нет. Подскажите где «копать».

Ответить 24.12.2021 05:46

Анатолий

Добрый день код ошибки F 060

Ответить 14.03.2023 08:21

Виктор Романенко

Ищу техническую информацию по бесконтактным конечным выключателям SEUSTER Typ: EWE 1.

Ответить 15.06.2023 19:24

Сергей

ребята подскажите пароль для скрытых опций? сейчас стоит уровень доступа 2
и еще ошибка 928 постоянно висит, куда копать?

Ответить 10.08.2023 11:17

Ильшат

Код ошибки F060 как убрать

Ответить 10.08.2023 13:56

Ильшат

Скажите пожалуйста как скинуть ошибку F060

Ответить 13.08.2023 14:12

TechFile

Ошибка F.060, причини:

• Дверь была разбита.
• Дверь не была полностью открыта при отключении питания.
• Датчики столкновения в SoftEdge или проводка датчика столкновения неисправны.
• Процедура аварийного сброса не завершена.

Неисправности могут быть квитированы, если они не сброшены
автоматически

Причина неисправности должна быть устранена прежде, чем
соответствующее сообщение подтверждается.

Для этого вы нажимаете кнопку STOP и держите ее нажатой
и затем нажмите кнопку EMERGENCY STOP.
В качестве альтернативы можно удерживать нажатой кнопку STOP приблизительно 5 секунд.

Источник

BK150FUEH

014634 GB

24.08.2009

Hörmann KG Verkaufsgesellschaft

D-33803 Steinhagen

1. S400 -> „ON“

11.

14.

16.

12.

15.

3. 4.

6. 7.

LIDL / V2012

P991

0 V3515Iso

V5015SE/ V5030SE / V6030SE 1

H3530

V2715SER

V3009

V2515FoodL

2 V6020TR

3 Turboflex V4530 8

P991

10.

13.

17. S400 -> „OFF“

HOE_PROFILANLEITUNG.DOC

21. Jul. 2009

•Commissioning Of Mainboards With

Integrated Frequency Inverter And DES

• Are all polarity components connected with correct

?

• Then the 7 segment display will blink

E.I.C.H

blink after switching on the panel .

.

• Door now

.

end positions can be set by foil key pad

• If

E.I.C.H.

blinks the programming procedure starts briefly pressing STOP.

Enter Programmig mode

!

• E.i.E.u

in dead the display

man blinks mode changes fast to

. To save to a set slower the press fully

and

blinking close position hold stop until

• E.i.E.o.

in dead man

. Now mode . set the

Saving fully is open position also

. Also continuously pressing

the also

done by

STOP push button

.

• The display already be used limits .

now changes in to automatic

Eo —

mode

. The

door

within the can

the

set

E.I.C.H.

won ´ t t blink ?

• No problem ! Switch off panel with mains switch display goes off switch in the

. Wait until open control panel and set the single right part

„

“

DIL position . right part of the mainboard

Now push the emergency the panel again .

stop to the stop button and switch on

• The display now mode foil

. key

Choose pad . shows

Briefly

P000 parameter press and

P999

STOP

. is in the programming

. with the arrow and arrow keys on the and change the displayed value

The from display

1 to 2, press changes

STOP back to until

P000 the dot again .

stops blinking .

• Choose parameter

P210

, briefly press stop and increase the displayed value from 0 to 3.

• Press STOP and hold until the dots stop blinking .

• Pull out the before .

emergency stop button and continue as said

Corrections necessary ?

• Press the

emergency

stop button

P000 in the programming mode .

.

The display

shows

• To correct parameter choose the

P231

P221

.

end

, limit for open position crrection of the choose

end

limit close

• Briefly forget dots press to stop

STOP save

blinking

and set correction continuously values

pressing

.

STOP

Don

until

´ until t

the

Test Correction Values Now !

!

• Pull out the emergency stop button

and

test the end limit positions

.

• If the end

limits

still

are

not

ok correct again

.

• Corrections ok and programming done ?

Switch off the control panel

DIL

—

again and …

and switch back wait to the for

„ the

OFF “ display going position , off , set switch on

It Functions !!

• As it is ment to do

.

• If still with problems the occure documentation that give you us cannot a call . fix

• • P.S.: … Up to diagram …

here all items will be found in the operation manual that is part of the wiring

•(GB)

8.2a

8.2b

8.2c

W1 W2

(W51)

W4 W3

W2 (W51)

V 5015 SE / V 5030 SE

V 6030 SE

3 4

V 2715 SE R

0 1 2 3 4

BK 150 FUE H (HS) / BS 150 FUE H (VA)

SoftEdge

H28-283

wiring diagramme adjustment instructions

6 7 8 9

SEUE001D.F26 / LIE / 12.04.2007

GB main supply connecting lead control voltage year of manufacture

Änderung Datum Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

230V / 50Hz min. 3×2,5mm²

24V DC

2008ff

Ers.f.

Subject to technical changes!

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

title page

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

H28-283

Gesamt

Blatt

0 1

Page Page name

4 title page contents mains supply impulse generator contact bar photocells output module radar (optional) option option

DES terminal connection diagramme X13 terminal connection diagramme X14 terminal connection diagramme X15 terminal connection diagramme X21A terminal connection diagramme X21B connection diagramme X3 connection diagramme X3.1

connection diagramme X3.2

cable overview parts list parts list

2 3 4 5 6

Spalte X: eine automatisch erzeugte Seite wurde manuell nachbearbeitet additional page field

7 date

24.08.2009

8 9

SEUJ005D.F06/LIE/12.04.2007

person in charge

TW ws21 ws21 ws21 ws21 ws21 ws21 ws21 ws21 ws21

TW ws21 ws21

TW ws21 ws21 ws21 ws21

Änderung Datum Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

Ers.f.

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

contents

H28-283

Gesamt

Blatt

0 1 circuit board

X11

L N L1

2 3 4

X16

31 32 30

X11

/ H1:N 7.1

/ X14:11 7.1

6 7

X16

31 32 30

X11

X11 : BK

X16 : BK

X13 : GN

X12 : GN

X13

T1 T2 T3

8 9

PE PE PE

X12=PE

Ölflex-110

10×0,5mm² control cable

7 8 W2

Ölflex-110

10×0,5mm² control cable

7 8

LT16

KH16B

LIYCY-JZ

4×1,5mm² motor cable

1 2 3 PE

SH=WH

PE PE PE

L N PE

CEE mains supply

230V/50Hz

Änderung Datum connecting lead:

3×2,5mm² fuse: 16A slow-acting

Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

CEE

Urspr.

mains switch

BK150FUE-HHS optional

Ers.f.

L N PE mains switch

BS150FUE-H optional

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

BN BU

A2 brake mains supply

BN BU

A2 operating current brake (optional)

U V W PE PE

U V

PE operator

H28-283

Gesamt

Blatt

X21A : BK

X21B : OR

X22 : BK

X24A : GN

X26 : BK

0 circuit board

24V

SK2 watchdog

E201

F201

=NA=

1 2

X24A

E212

F212

/ X23:61 11.5

IN1

E101

24V

X21A

40 41

X26

IN2

E102

24V

40 42

IN3

E103

24V

40 43

5 6

IN4

E104

24V

X21B

44 45

IN8

E108

24V

X22

55 54

IN10

E110

24V

50 51

IN9

E109

24V

50 52

S35

IN7

E107

24V

57 56

WS32

Ölflex-110

2×0,75mm² impulse up

S32

WS33

Ölflex-110

2×0,75mm² impulse down

S33

WS34

Ölflex-110

2×0,75mm² impulse operation

S34

WS36

Ölflex-110

2×0,75mm² intermediate stop (optional)

S36 external emergency-OFF 2 emergency-OFF

Änderung Datum option

Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

impulse up

Ers.f.

impulse down impulse operation

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

no photocell 2 for jumper impulse generator reserve

USV optional intermediate stop

(optional) sluice on/off interlock ON/OFF option

H28-283

Gesamt

Blatt

0 circuit board

1 2

+24

+12

GND1

E360

F361/F363/F364

X27

X22

X27

X24B

74 73

X27

X24B

X27

WX.3

X.3

—

5 4 1 6 2 3

—

5 4 1 6 2 3

IN6

E106

Activation

X22

X27

X24B

X27

X3.1

7 8 9 10 11

WA5.1

LIYY_757

5×0,5mm² contact bar

A5.1

BN WH GN

+24

GND contact bar

A5.2

S51.2

WA5.2

LIYY_757

4×0,14mm²

Diodes

BAT

WS51

Ölflex-110

2×0,5mm² crash protection

S51.1

BN WH battery crash protection

8 11

BN YE

YE GY

YE GY crash protection

Activation

1 2 3

WS30.1

LIYY_757

3×0,14mm² contact bar receiver

S30.1

BN WH GN contact bar receiver

WS30.2

LIYY_757

3×0,14mm² contact bar transmitter

S30.2

BN WH GN contact bar transmitter contact bar

Änderung Datum Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

Ers.f.

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

7 8 9

IN5

E105

X21C

X27

H28-283

/ X3.2:3 6.0

/ X3.2:2 6.0

/ X3.2:1 6.0

Gesamt

Blatt

0 1 2 3 4 5 6 7 8 9

X.3:3 5.8

X3.1:8 5.8

X3.1:7 5.8

X3.2 : 1 — BN

X3.2 : 2 — BU

X3.2 : 3 — WH

X3.2 : 4 — BN

X3.2 : 5 — BU

X3.2 : 6 — WH

24V

GND

IN5

E105

X21C

47 49 48

X27

X3.2

1 2 3 4 5 6

X3.2 : 1 — #1

X3.2 : 2 — #2

X3.2 : 3 — #4

X3.2 : 4 — #3

X3.2 : 1 — BN

X3.2 : 2 — BU

X3.2 : 4 — BN + BK

X3.2 : 5 — BU

X3.2 : 6 — WH

X3.2

1 3 4 2

X3.2

1 2

X3.2

4 4 5 6

X3.2 : 1 — BK

X3.2 : 2 — BU

X3.2 : 4 — BK + BN

X3.2 : 5 — BU

X3.2 : 6 — WH

X3.2

1 2

X3.2

4 4 5 6

LIYY_757

4×0,14mm² photocell transmitter

BN BU WH

ASD_757

4×0,14mm² photocell receiver

BN BU WH

WS4

Ölflex-110

4×0,75 photocell

1 4

ILG

W(S41.1)

ASD_ILG

3×0,14mm² photo grille transmitter

BN BU

W(S41.2)

ASD_ILG

4×0,14mm² photo grille receiver

BN BK BU WH

W(S41.1)

ASD_757

2×0,14mm² photo grille transmitter

BK BU

ALG

option

W(S41.2)

ASD_757

5×0,14mm² photo grille receiver

BK BN BU WH

EWS transmitter

RES

—

EWE

+ —

Out photocell transmitter

Änderung Datum option

Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

photocell receiver option

Urspr.

+ NO

COM photocell option

Ers.f.

S41.1_ILG

+24 GND TE

BN BU WH

S41.2_ILG

+24 COM GND NO

BN BK BU WH

S41.1_ALG

+24 GND

BK BU photo grille transmitter option

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

photocells photo curtain receiver option

S41.2_ALG

+24 COM GND NO NC

BK BN BU WH GY photo grille transmitter option

H28-283 photo curtain receiver option

Gesamt

Blatt

0 circuit board

P701

X16:31 3.5

X11:N 3.5

X14

11 12 10

2 3

P701

X14

11 12 10

WH1

Ölflex-110

3×0,75mm² traffic light

WH2

Ölflex-110

2×0,75mm² flashing beacon

H1 traffic light

H2 flashing beacon

N G

4 5

P701

X14

11 12 10

6 7

P702

X15

21 22 20

8 9

Änderung Datum traffic light option

Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

flashing beacon option

Ers.f.

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

door open signal output module door closed signal

H28-283

Gesamt

Blatt

0 circuit board

IN4

E104

24V

GND

X21B

44 46 44 45

24V

X21A

IN1

E101

3 4

24V

GND

X21B

44 46 44

5 6

24V

X21A

IN1

E101

24V

GND

X21B

44 46

IN4

E104

24V

X21A

IN1

E101

.WA8

COMFORT

8×0,34

GN BN PK VT BK WH GY YE

WA8

COMFORT

8×0,34

GN BN PK VT BK WH GY YE

WA9

COMFORT

8×0,34

GN BN PK VT BK WH GY YE

.A8

COMFORT

+24

GND

COM

COMFORT

+24

GND

COM

COMFORT

+24

GND

COM

Änderung Datum radar (optional)

Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

1 x COMFORT

Urspr.

Ers.f.

radar (optional)

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

radar (optional)

2 x COMFORT

radar (optional)

H28-283

Gesamt

Blatt

0 circuit board

1 2

E501 E502

3 4 5 6

3 4

IN4

E104

24V

GND

X21B

44 46 44 45

5 6

IN1

E101

24V

GND

24V

X21B

44 46 44

X21A

7 8

E401

A6 radio receiver

WA4

Ölflex-110

4×0,5mm² photocell 2 (optional)

1 2 3 4 WA7

Ölflex-110

4x0mm² radar

1 2 3 4

L1 L2

Änderung Datum Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

induction loops

(optional)

Urspr.

2 3

1 4

+ COM

Ers.f.

photocell 2 (optional)

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

option radar (optional)

H28-283

Gesamt

Blatt

0 1

A1.1

3 4

.X4

TST-RFuX-COM

1 2 3 4 5 6

.X3

1 2 3 4 5 6

A2.1

Änderung Datum Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

TST-RFuX-COM

#2

.X4

1 2 3 4 5 6

.X3

1 2 3 4 5 6

Ers.f.

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

option

6 7 8

automatic sluice operation interlock

H28-283

Gesamt

Blatt

0 circuit board

1 2

VT colours according to IEC757 black GY grey brown red orange yellow green blue purple

SR white pink gold turquoise silver

GNYE green-yellow violet

3 4 5

F752

A B

+12

GND

X25

81 82 80 83

X24A:70 4.1

E211

F211

X23

60 61

W2 1 2 3 4 5 6

4 2 6 3 5 1

S10 crank handle

2.1

1.4

2.2

2.5

1.2

1.6

1.3

DES

1.5

1.1

2.6

2.3

2.4

F0 thermal contact

7 8

E000/E050/E090

X400

F1 F2 F3 F4

WSF membrane keypad

Änderung Datum Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

Ers.f.

DES

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

external emergency-OFF 1

DES

H28-283 membrane keypad

Gesamt

Blatt

0 1 2 3 4 5 6 7 8 9

X13 motor connection

Klemmennummer

1 2 3 PE SH

PE SH

Änderung Datum Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

Ers.f.

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

terminal connection diagramme

X13

H28-283

Gesamt

Blatt

0 1 2 3 4 5 6 7 8 9

Klemmennummer

X14 door open signal

R G

Änderung Datum Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

Ers.f.

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

terminal connection diagramme

X14

H28-283

Gesamt

Blatt

0 1 2 3 4 5 6 7 8 9

Klemmennummer

X15 door closed signal

Änderung Datum Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

Ers.f.

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

terminal connection diagramme

X15

H28-283

Gesamt

Blatt

0 1 2 3 4 5 6 7 8 9

Klemmennummer

X21A

WH YE WH YE WH YE 4

S32

4 3

S33

4 3

S34

4 WH

WH YE

.A8

WH YE

COM

—

COM

Änderung Datum Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

Ers.f.

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

terminal connection diagramme

X21A

H28-283

Gesamt

Blatt

0 1 2 3 4 5 6 7 8 9

Klemmennummer

X21B option

GN BN PK VT GN BN PK GN BN VT 1 2 3 4 1 2 3

PK VT

.A8

BN PK

BN VT

2 3

—

COM

Änderung Datum Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

Ers.f.

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

terminal connection diagramme

X21B

H28-283

Gesamt

Blatt

0 1 2 3 4 5 6 7 8 9

Anschluß

BN BU

X3 limit switch box

U V W PE PE 4 2 6 3 5 1

BN BU

SW SW

U V

PE 1.4

1.2

1.6

1.3

1.5

1.4

1.1

Änderung Datum Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

Ers.f.

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

connection diagramme X3

H28-283

Gesamt

Blatt

0 1 2 3 4 5 6 7 8 9

X3.1

contact bar

Anschluß

Änderung Datum Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

Ers.f.

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

connection diagramme X3.1

H28-283

Gesamt

Blatt

0 1 2 3 4 5 6 7 8 9

X3.2

photocell

Anschluß

—

+ —

RES

—

+ —

Out

—

COM

+24

GND

+24

BN BU BK

+24 GND COM

+24

GND

+24

BK BU BN

+24 GND COM

+24

Änderung Datum Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

Ers.f.

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

connection diagramme X3.2

H28-283

Gesamt

Blatt

cable overview

WA9

.WA8

WH1

WH2

WS4

WS32

WS30.2

WS33

WS34

WS36

WS51

WA8

WSF

WX.3

W(S41.1)

W(S41.2)

WA4

WA5.1

WA5.2

WA7

WS30.1

A5.2

X21A

X22

A5.2

X21B;X21A

X14

X3.2

X21A

X400

X.3

X3.2

A1.1-.X4

X3.2

X21B

X3.1

A5.2

X21B;X21A

A5.2

3 4 5 6

S30.2

S33

S34

S36

S51.1

.A8

H2;X14

S32

X27

X13

X16;X11;X25;X23

EWS

EWE

A2.1-.X4

S41.1_ILG;S41.1_ALG

S41.2_ILG;S41.2_ALG

A5.1

S51.2-S;S51.2-E

S30.1

LIYCY-JZ

Ölflex-110

LIYY_757

ASD_757

ASD_ILG

Ölflex-110

LIYY_757

Ölflex-110

LIYY_757

Ölflex-110

COMFORT

Ölflex-110

1,5

0,5

0,14

0,34

0,75

0,14

0,75

0,5

0,34

0,14

0,5

0,14

7 8 9

Spannung

V motor cable control cable photocell transmitter photocell receiver photo grille transmitter photo grille receiver photocell 2 (optional) contact bar

Diodes radar contact bar receiver contact bar transmitter impulse down impulse operation intermediate stop (optional) crash protection

SEUS001D.F10 / LIE / 12.04.2007

Page

0 traffic light flashing beacon photocell impulse up membrane keypad

Änderung Datum Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

Ers.f.

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

cable overview

H28-283

Gesamt

Blatt

0 1

parts list

NAME

WIRING DIAGRAMME LOCATION

MENGE

11.4

EWS

6.0

3.4

7.1

9.6

5.0

9.8

5.0

A5.2

5.0

A5.2

9.1

9.4

A5.1

5.0

A5.2

3.1

A1.1

10.2

8.4

8.7

DES

2 3

DESIGNATION

Schaltschrank BS 150 FUE H 400x300x150mm

Schaltschrank BS 150 FUE H VA 400x300x150

Steuerung BK 150 FUE H

Steuerung BK 150 FUE H HS

Platine E FU H Erweiterungsplatine

Induktionsschleifendetektor 1-Kanal

Induktionsschleifendetektor 2-Kanal

Lichtschranke mit Reflektor

Gehäuse Kabellose Impulsübertragung

Platine Kabellose Impulsübertragung

Batteriehalter 2XUM2 Softedge

Batterie für kabellose Impulsübertragung

Platine Funkempfänger 868,3MHz 1K

Radar-Bewegungsmelder

Radar & Präsenzmelder COMFORT

Digitaler Endschalter

Lichtschranke Einweg o. Kabel

Bremsgleichrichter EGR2

Ampelgehäuse Rot/Grün Nr. 0671/s-2-E

Änderung Datum Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

Ers.f.

MODEL NUMBER

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

TST-FUH CX-SE

013768

RFUx-COM

TST SUVEK1

TST SUVEK2

OPT-CF 1163

10004300

Halter 2xUM2-DK

MN 1400, 9800mAH

MWD BF1-A

MWD BP

COMFORT

DES

EWS/EWE

EGR2

5 parts list

6 7 8 9

MANUFACTURER

Sarel GmbH

Feig Electronic GmbH

Deutsche Telemecanique

FRABA AG

Reichelt Elektronik

Carl Scobel GmbH

Deltron GmbH

Feig Electronic GmbH

Gesellschaft für Antriebstechnik

Witt Sensorik

Gesellschaft für Antriebstechnik

013561

013562

011948

800187

800187.1

014862

010681

010073

013341

800252

SEUO001D.F01 / LIE / 12.07.2007

ARTICLE NUMBER

POS.

BS150FUEH

014715

BS150FUEH-V2A

014716

013768

BK150FUEH-HS

014466

013772

800256

800257

800232

013551

013550

H28-283

Gesamt

Blatt

0 1

parts list

3.3

6.3

7.2

3.2

NAME

WIRING DIAGRAMME LOCATION

MENGE

7.2

4.0

S30.1

5.4

S30.2

5.5

S41.1_ALG

6.7

S41.1_ALG

6.7

S41.1_ILG

6.4

S41.1_ILG

6.4

S51.1

5.1

S51.2

5.2

S51.2

5.2

11.8

X3.1

5.4

2 3

DESIGNATION

Blitzleuchte orange

Blitzleuchte rot

Hauptschalter abschließbar BK150FUE H HS

Lasttrennschalter 16A

Lichtschranke mit Reflektor

Not-Aus Taster

Not-Aus Schild

Opto Empfäng.kabell. Datenübertr. Antr.s.

Opto Sender kabell. Datenübertr. Lagers.

Lichtgitter ALG Bauhöhe 510mm

Lichtgitter ALG 70

Lichtgitter ILG Bauhöhe 1590mm

Lichtgitter ILG Bauhöhe 510mm

Feder m.Schalter 7000mm

Federschalter m. Diode Antr.seite rechts

Federschalter m. Diode Antr.seite links

Folientastatur 155,3×119,6mm mit Fenster

Drucktaster Auf-Halt-Zu für V2A-Schrank

Folientastatur klein 100x60mm

Tastaturverlängerung 250mm

Platine Getriebe

Änderung Datum Name

Datum

Bearb.

Gepr.

Norm

Lie

24.08.2009

Urspr.

Ers.f.

MODEL NUMBER

683-ALG+70K5BR-K14

685-ILG-24/06-L-K1-10

685-ILG-06/06-L-K1-10

78-004-006

78-004-007

805349

Hörmann KG

Verkaufsgesellschaft

D-33803 Steinhagen

Ers.d.

WAH814/LT16/3VZM/Z20/X83/FR

KH16B

XB7ES542P parts list

MANUFACTURER

Kraus & Naimer

Deutsche Telemecanique

Schneider Electric

Deutsche Telemecanique

Schneider Electric

FRABA AG

Strack Lift Automation

Felsch Spritzguß GmbH

Joetec

Kundisch GmbH

Lück Elektrosysteme GmbH

MAB Electronic

8 9

SEUO001D.F01 / LIE / 12.07.2007

ARTICLE NUMBER

POS.

013725

013724

800265

011167

800464

800465

011864

013563

800261

800255

014351

370041.1

800232

011440

011442

013564

014142

011874

370079

010566

014468

BK150FUEH-HS

BS150FUEH

BS150FUEH-V2A

BS150FUEH

BS150FUEH-(V2A)

H28-283

Gesamt

Blatt

TST Initial Operation TST FUH

BK150FUEH

Important:

These instructions must be read before connecting the control and before initial operation of the door system!

Hörmann KG Verkaufsgesellschaft

D-33803 Steinhagen

HOE_FUH_GB.doc Hörmann KG Verkaufsgesellschaft Page 1 of 30

TST Initial Operation TST FUH

Notes

Hörmann KG Verkaufsgesellschaft

D-33803 Steinhagen http://www.hoermann.de/

With this edition, all previous editions become invalid.

The specifications in this document may be modified without notice.

The circulation and reproduction of this document, as well as the use and distribution of its contents, is not permitted without our express permission. Compensation is required in case of infringement. All rights reserved in case of patent grant or design registration.

This manual has been composed especially for those people fitting the door control TST FUH from Hörmann

KG Verkaufsgesellschaft. Initial operation of the control may only be carried out by electrical specialists with accredited training familiar with the safety standards for electrical operator and automation systems.

The completeness of the initial operation manual is the sole responsibility of the person carrying out initial operation of control TST FUH.

This manual shows only a small selection of control functions. For additional functions and descriptions of individual door functions, more exact control specifications and warnings, see the additional information.

We have compiled the information in this document to the best of our knowledge. Hörmann KG

Verkaufsgesellschaft does not guarantee the accuracy and completeness of the specifications in this document. A.Seuster GmbH & CO KG may especially not be held liable for consequential damages due to defective or incorrect specifications. Despite our best efforts, errors can never be completely avoided. We are happy to receive feedback at any time.

The installation recommendations in this document assume favourable general conditions. Hörmann KG

Verkaufsgesellschaft does not guarantee faultless operation in non-system environments.

Hörmann KG Verkaufsgesellschaft does not guarantee that the information contained in this document is free of foreign industrial property rights. With this document, Hörmann KG Verkaufsgesellschaft does not grant licences on its own or foreign patents or other property rights.

Warranty claims against Hörmann KG Verkaufsgesellschaft only apply to the immediate contractual partner and are non-transferrable. Warranty will only be accepted for products that have been supplied by Hörmann

KG Verkaufsgesellschaft. We assume no liability for the total system.

The product descriptions, the products’ use, options and performance data are not valid as warranted characteristics and are subject to technical modifications.

General information on this document

In this functional description, the following symbols are used to alert the reader to various danger points and helpful hints.

IMPORTANT

Indicates potential danger to

persons if the procedure is not carried out as described.

Indicates information which is important for door control or door function.

)

Indicates information which is useful, but not

Indicates danger to the control.

absolutely necessary, for using door control TST

FUH.

Hörmann KG Verkaufsgesellschaft Page 2 of 30 HOE_FUH_GB.doc

TST Initial Operation TST FUH

Contents

1 Safety instructions

2 Technical data

3 Fitting the control

4 Electrical connection

4.1

8

Connecting the supply voltage………………………………………………………………………………………9

5

6

7

4.2

4.3

Motor connection ………………………………………………………………………………………………………..10

Connecting the safety strip………………………………………………………………………………………….11

4.4

Connecting the limit switch …………………………………………………………………………………………12

4.4.1

Absolute encoder

……………………………………………………………………………………………………12

4.4.2

Mechanical limit switches

……………………………………………………………………………………….12

5 General operation information for parameterisation

5.1

13

Modifying parameters………………………………………………………………………………………………….14

6 Initial operation…

6.1

14

… with absolute encoder ……………………………………………………………………………………………..14

6.2

… with mechanical limit switches…………………………………………………………………………………14

6.3

Requesting new teach-in for limit stops……………………………………………………………………….15

7 Further connection options

7.1

16

Photocell …………………………………………………………………………………………………………………….16

7.2

External command controllers …………………………………………………………………………………….16

Overview of outputs

8 Overview of inputs

17

18 9 Functions 19

9.1

Software update ………………………………………………………………………………………………………….19

9.2

9.3

Door cycle counter………………………………………………………………………………………………………19

Maintenance counter …………………………………………………………………………………………………..19

9.4

9.5

Hold-open phase …………………………………………………………………………………………………………19

Warning phase before door cycle/clearing time ……………………………………………………………20

9.6

9.7

Limit stop correction …………………………………………………………………………………………………..20

CLOSE movement……………………………………………………………………………………………………….20

9.7.1

Correct travel limit door CLOSE

………………………………………………………………………………20

9.7.2

Start of the CLOSE movement

…………………………………………………………………………………21

9.8

OPEN movement …………………………………………………………………………………………………………21

9.8.1

Correct travel limit door OPEN

………………………………………………………………………………..21

Hörmann KG Verkaufsgesellschaft Page 3 of 30 HOE_FUH_GB.doc

TST Initial Operation TST FUH

9.9

9.8.2

Start the opening

……………………………………………………………………………………………………21

9.8.3

Diagnostic display on the screen

…………………………………………………………………………….22

Error memory ……………………………………………………………………………………………………………..22

9.10

Software version …………………………………………………………………………………………………………23

9.11

Door operating time …………………………………………………………………………………………………….23

9.12

Input voltage measurement …………………………………………………………………………………………23

9.13

Operating mode of the control …………………………………………………………………………………….23

9.14

Password ……………………………………………………………………………………………………………………24

9.15

Memory time for opening commands …………………………………………………………………………..24

10 Parameter overview

11 Overview of messages

24

25

11.1

Internal system-induced errors F.9xx …………………………………………………………………………..28

11.2

Information messages …………………………………………………………………………………………………29

Hörmann KG Verkaufsgesellschaft Page 4 of 30 HOE_FUH_GB.doc

TST Initial Operation TST FUH

Strictly observe the following important safety instructions, as well as the fitting and connection instructions, during initial operation and operation of the control:

— All installation, initial operation and maintenance work must be carried out exclusively by qualified personnel.

The following regulations must be observed with special care: VDE0100, EN 50110 (VDE0105), EN 60204

(VDE0113), EN 50178 (VDE0160), EN 60335 (VDE0700), fire prevention regulations, accident prevention regulations, as well as the relevant applicable regulations for industrial doors (ZH1/494, EN12453, EN12978)

— The control may only be opened if the supply is disconnected at all poles.

— If the voltage-free contacts of the relay outputs or other contact points are externally fed, e.g. operated with a dangerous voltage that may still be present after switching off the control or pulling the mains plug, a respective warning label must be clearly visible on the control housing. («Attention! Switch off all mains current circuits before accessing the connecting terminals.»)

— Do not operate the control if it is open.

—

Operating the control with a dismantled CEE plug is only permitted if the mains supply can be disconnected from the control at all poles via a suitable switch. The mains plug or the replacement switch used must be easily accessible.

— To avoid danger, the connecting cable of the unit, if damaged, must be replaced by the manufacturer, his aftersales service or a similarly qualified person.

— Even after the supply has been switched off, dangerous voltages are present in the intermediate circuit capacitors for up to five minutes. The discharge time for voltages under 60 V DC is at most 5 minutes. Touching internal control parts during this discharge time is dangerous.

— A defective power supply unit may considerably increase the discharge time of the intermediate circuit capacitors to a voltage value under 60 V DC. Discharge times of up to 10 minutes may result.

— If the 24 V control voltage is short-circuited or extremely overloaded, the power supply unit will not switch on even though the intermediate circuit capacitors are charged. Display and LEDs remain dark. The power supply unit can only be switched on after the short-circuit or extreme overload has been remedied.

— The power supply unit is fed by the intermediate circuit capacitors for several seconds after the supply has been switched off and continues its supply function for a period of time, depending on the power supply unit load. In this case, the V 805 glow lamp lights up until the voltage has decreased.

— Sections of the processor circuits are directy linked galvanically to the power supply. This must be considered when carrying out any possible control measurements (when carrying out measurements in this area of the process circuit, do not use measurement instruments with PE reference of the measuring circuit).

— Do not operate the control without a connected protective earth conductor. If the protective earth conductor is not connected, dangerously high voltages occur on the control housing, due to leakage capacities. The protective earth conductor must be connected according to EN 50178, paragraph 5.2.11.1 for increased leakage currents >3.5 mA.

— If the control is covered in condensation, do not switch it on or operate it. This can destroy the control.

— If controls are used outside the specified temperature range, a regulated, monitored heating system must be provided to ensure that the specified operating temperature is maintained when switching on and operating the control.

— Do not operate a control with damaged keypad or vision panel. Damaged keypads and windows must be replaced. To prevent damage to the keypad, do not operate it with sharp objects. The keypad is designed for finger operation.

— Before switching on the control supply for the first time, ensure that the evaluator cards (plug-in modules) are plugged in the correct position. The control may be damaged if the cards are not plugged correctly or are twisted, or if non-approved cards from other manufacturers are used.

— When operating the door in dead-man mode, ensure that the door area is visible to the person operating the door, as safety devices such as the safety strip and photocell do not activate in this mode.

— Check the parameter settings and the function of the safety devices. Parameters, bridges and other command units may only be set by instructed personnel.

Non-compliance with this safety information may endanger personal health and safety, and may also damage the control.

These safety instructions do not claim to be complete. Please contact your supplier if you have any questions about the product.

The manufacturer has carefully checked the unit hardware and software, as well as the product documentation, but can not guarantee that it is free of errors.

The user must label the unit (type plate with name and address of manufacturer, serial number, type designation, supply voltage and temperature range).

Hörmann KG Verkaufsgesellschaft Page 5 of 30 HOE_FUH_GB.doc

TST Initial Operation TST FUH

Dimensions of housing (W x H x D):

Fitting:

Supply voltage via L, N, PE:

Own consumption of control: external supply 1 (230 V):

Control voltage/external supply 2:

Control voltage/External supply 3:

Control inputs:

Inputs INK 1 and INK 2:

RS485 A and B:

Safety chain/Emergency-off

Safety strip input:

Alarm signal

Relay outputs

USB

Communication module

HOST

Alternatively

Device

Relay K3:

Standard braking relay:

200 x 400 x 175 mm (without wall holder)

Via wall holder on floor of housing, standing vertically

230 V

±10%, 50…60 Hz permissible range: 110…240 V ± 10%/50…60 Hz

Fuse: 16 A K Characteristics max. 30 W when fully equipped

230 VAC

±10%, 50…60 Hz

(fused on the printed board: F202/1 AT)

24 V

regulated (±5% at nominal voltage 230 V) max. 500 mA to 40 °C, max. 250 mA to 50 °C incl. optional plug-in modules

Fused via self-resetting semiconductor fuse, short-circuit proof via central circuit regulator

For electronic limit switch and safety strip

Nominal value 11.5 V/max. 130 mA

24 VDC/type 15 mA, max. 26 VDC/20 mA all inputs must be connected potential-free or:

< 5 V: inactive Æ logical 0

> 7 V: active Æ logical 1

Min. signal length for input control commands: > 100 ms

Galvanic separation via optoelectronic coupler on printed board

For two 24 V active impulse inputs offset by 90°, with max. load of 20 mA

< 5 V: inactive Æ logical 0

> 16 V active Æ logical 1

Only for electronic limit switches

RS485 Level, terminated by 100 Ω

All inputs must be connected voltage-free

Contact loading capacity: ≤ 26 VDC/ ≤ 120 mA

If the safety chain is interrupted, no operator movement is possible, not even in deadman mode

For electrical safety strips with 8.2 kΩ terminating resistor and for dynamic optical systems

24 VDC/min. 10 mA/max.100 mA

Only Ohmic loads!

If inductive loads (e.g. additional relays or brakes) are connected, these must be equipped with corresponding interference suppression (recovery diode, varistors, RC modules).

For USB Memory Sticks (PC compatible)

Plug connector: Type A

Max. power consumption: 100 mA

Max. cable length 2 m

For PC communication with Feig protocol

Plug connector: Type B

Max. cable length 2 m

Only suitable for TST RFUxCom

Changeover contact for releasing electromechanical brakes with upstream brake rectifier

230 VAC/3 A

If EMERGENCY-OFF is activated, the brake relay will be released.

Relays K1 and K2:

«Malfunction/door position signals/traffic light functions»

Volt-free change-over contact min. 10 mA max. 230 VAC/3 A

Contacts used for power switching can no longer switch small currents.

Operator output:

Brake resistance load (optional):

For operators up to 1.5 KW at 230 V

Motor constant current at 100% on-time and 40°C ambient temperature: 10 A

Motor constant current at 60% on-time and 50°C ambient temperature: 8 A

May be briefly overloaded up to 20 A for 0.5 s

Max. length of motor cable: 15 m

Max. 1.5 KW for max. 0.5 seconds.

Repeat rate min. every 20 seconds.

Temperature range (TST FUH- CXP)

Operation:

Storage:

Temperature range (TST FUH- CX)

Operation:

For printed boards, observe the own heat in the housing!

-20 … + 70 °C

-25 … + 70 °C

Installed in the housing

-20…+50 °C

Storage:

Humidity

Vibration

Protection category

Up to 80% non-condensing

Low-vibration fitting, e.g. on a masonry wall

IP 54

Hörmann KG Verkaufsgesellschaft Page 6 of 30 HOE_FUH_GB.doc

TST Initial Operation TST FUH

Directive Standards:

EMC Directive: 2004/1/08/EC

Low-voltage directive:

EN 61000-6-3:

EN 61000-6-2:

EN 61000-6-4:

EN 60335-1/02.2007:

2006/9/5/EC

Emitted interference, residential environments

Interference resistance, industrial environments

Emitted interference, industrial environments

Safety of electrical equipment for domestic use and similar purposes/Part 1

Type-tested according to:

Applied national technical specifications regarding the directives above

EN12453/02.(2001):

EN12445/02.2001:

EN 61508:

EN12978/09.2003:

Doors and Gates – Safety in Use of Power-Driven

Doors — Requirements

Safety in use of power operated doors – Test methods

Functional safety of electrical/electronic/programmable electronic safetyrelated systems

Doors – Safety devices – Requirements and test methods

The system must be switched voltage-free while fitting the control.

• Before fitting, check the control for shipping

damage or other damage. In some cases, damage inside the control may cause considerable consequential damage to the control and even endanger the health and safety of the user.

• Touching the electronic components, especially

those of the processor circuit, is prohibited.

Electronic components may be damaged or destroyed by electrostatic discharge.

• Before opening the housing cover, make sure

that no borings lying on the cover can fall into the housing.

• Ensure that the control is fitted free of torsion.

• Unused cable entries must be closed by suitable

measures to maintain the housing’s IP54 protection category.

•

Do not subject the cable entry points to any loads, particularly tensile loads.

Min. 100 mm

1x 230 VAC,

N , PE

Min. 100 mm

-20 °C

50 °C

Figure 1: Fitting the control

Hörmann KG Verkaufsgesellschaft Page 7 of 30

Figure 2: Drilling diagram

HOE_FUH_GB.doc

TST Initial Operation TST FUH

•

Connection, testing and maintenance of the open control may only be carried out in a voltage-free state. Closely observe the points listed in the safety instructions section.

After the control is switched off, dangerous voltage is still present for up to 5 minutes.

Due to residual voltages, touching the electronic components is dangerous.

Never operate the control when the housing cover is open.

•

After completing the wiring and before switching on the control for the first time, check whether all motor connections on the control side and on the motor side are tightened and the motor is correctly connected in star or triangle. Loose motor connection usually cause damage to the converter.

•

All voltage inputs are galvanically separated from the supply by a basic isolator. All components attached to the control must have at least one additional isolation with a rated voltage of > 230 V (according to EN 60335-1).

•

For compliance with EMV directives, only shielded, separate motor cables may be used.

The shield must be connected on both sides

(motor and control) and no additional connections may be led in the cable.

Maximum cable length: 15 m.

•

Very high electrostatic charges may accumulate, especially with high-speed plastic

•

curtain doors. When this charge discharges, the control may be damaged. Therefore, suitable countermeasures must be implemented to prevent electrostatic charging.

Max. cross section for connections to printed board terminals: wire

(rigid)

Terminal screws

Plug-in terminals

Motor terminals

Mains voltage

2.5

1.5

2.5

2.5 stranded

(with/without wire end ferrule)

1.5

1.0

2.5

1.5

Hörmann KG Verkaufsgesellschaft Page 8 of 30 HOE_FUH_GB.doc

TST

4.1 Connecting the supply voltage

Initial Operation TST FUH TST Initial Operation TST FUH

IMPORTANT

The mains plug must be visible and accessible from the control.

Hörmann KG Verkaufsgesellschaft

Figure 3: Supply main connection

Page 9 of 30 HOE_FUH_GB.doc

Figure 4: Motor connection

IMPORTANT

To ensure smooth operation of door control TST FUH, a shielded motor cable must be used. Also, do not run any leads other than those of the motor connection in this cable.

Hörmann KG Verkaufsgesellschaft Page 10 of 30 HOE_FUH_GB.doc

TST

4.3 Connecting the safety strip

Initial Operation TST FUH

X27 X27

Coiled cable

Door leaf terminal box

70 71 72 73

«Electrical» strip

J 900: 1 — 2

Dynamic optical system

Coiled

3 cable

J 900: 1 — 2

Door leaf terminal box

70 71 72 73

Optional wicket door switch

Cable slack switch

8,2K

J900

1,2K

X27

57 58 59 70 71

X24A

72 73

X24B

74 75

Jumper

J600 is found on the top right corner of the circuit board

Inside

(Brown)

72 73

Brown White

Safety strip

Terminating resistor

Optional wicket door switch

Cable slack switch

Receiver

Green

White

Brown

72 73 74

Outside

(white)

Sender

Figure 5: Safety strip connection

Different types of safety strips may be connected, e.g.:

• Electrical safety strip with 8.2 kΩ terminating resistance.

• Dynamic optical systems.

If one of these types of safety strips is connected when door control TST FUH is switched on, it will be recognised automatically.

IMPORTANT If no safety strip is connected, no automatic access is possible.

Hörmann KG Verkaufsgesellschaft Page 11 of 30 HOE_FUH_GB.doc

TST Initial Operation TST FUH

4.4 Connecting the limit switch

Different types of limit switch systems may be used with door control TST FUH.

An absolute encoder is used as a limit switch in the standard setting. Furthermore, mechanical cam limit switches can be used.

+12V

GND

RS 485-B

Emerg.off chain

24V

Emerg.off chain

RS 485-A

Figure 7: Connecting the absolute encoder DES

Figure 6: Absolute encoder DES

4.4.2 Mechanical limit switches

Figure 8: Cam limit switch

Hörmann KG Verkaufsgesellschaft

Figure 9: Connecting the cam limit switch

Page 12 of 30 HOE_FUH_GB.doc

TST Initial Operation

)

Alternatively, the pre-limit switches may also be connected as NC contacts.

5 General operation information for parameterisation

TST FUH

Opening parameterisation mode

Disconnect door control

SERVICE

Switch the

S400 switch to

Disconnect supply at all poles

(Observe safety information)

Service mode is activated, close control box.

(For position of S400 see Chapter

5.1)

The 7-segment display will turn off after a delay of several seconds

STOP

(permanent)

¿ OPEN

(permanent)

Connect door control

OPEN or

Connect control

If service mode is active, the first decimal point will flash

Contents of display are dependent on

control status

Activate STOP button and hold Current messages will display, e.g.:

. . .

E. 2 0 1

Additionally activate OPEN button and hold

Wait approx. 2 seconds:

In parameterisation mode

P. 0 0 0

Selecting parameters in open parameterisation mode

Select desired parameter

A T T E N T I O N:

Not all parameters are directly visible or modifiable, depending on the password and the positioning type setting

The parameter value can be viewed or modified (see below)

Display varies with selection

P. . . .

3. or

4. or

STOP (short)

OPEN

Parameter processing with selected parameter

Control is in parameterisation mode

Name of desired parameter displays

Opening the parameter

Use the OPEN button to increase the parameter value

Use the CLOSE button to decrease the parameter value

0 1 0

The current parameter value is displayed:

If the currently valid parameter value is modified, the decimal points will flash

STOP (long)

STOP (short)

Save set parameter value

Discard set parameter value

Change to display the parameter name

The parameter is saved when all points have stopped flashing

Abort, the original parameter value is displayed

Display of parameter name

0 1 0

STOP (long)

Exiting parameterisation mode

Parameterisation mode is exited immediately, door mode is active again

The last saved value is automatically kept

. . . .

Perform a reset of the control

Å

+¿+À

Press these simultaneously and hold approx. 3 seconds.

IMPORTANT

After approx. 1h, the service mode will automatically set back. To re-enter service mode, briefly switch off the control and then switch on again, or carry out a reset.

Hörmann KG Verkaufsgesellschaft Page 13 of 30 HOE_FUH_GB.doc

TST Initial Operation

)

Modification of the basic data is not necessary; this was set at the factory.

To modify parameters, proceed as follows:

— Pull the mains plug.

— Switch the S400 DIP switch on.

— Plug in the mains plug.

— Simultaneously press the

STOP and the ¿ OPEN buttons for approx. 3 s to enter the parameterisation mode of the door control.

— Modify the desired parameters.

— After completing the settings, push the Å

STOP button for approx. 3 s to exit parameterisation mode.

Figure 10: Position S400

TST FUH

Before initial operation of the control, check the electrical connection and the correct position of the plug-in cards.

After initial start-up is complete, test the function of all safety devices. After initial operation is complete, test the function of all safety devices.

6.1 … with absolute encoder

1. Open CALIBRATION mode by briefly pressing the

STOP button

Move door to door CLOSED position using À CLOSE on the membrane keypad and save by pressing the

STOP button for approx. 3 seconds.

Move door to door OPEN position using ¿ OPEN on the membrane keypad and save by pressing the

STOP button for approx. 3 seconds.

Å the CLOSE button, move the door to approx. 50 cm before closed position

IMPORTANT If the door does not move, the motor is lacking in power or, if necessary, check if the brake is released.

IMPORTANT

The distance is very dependent on the door type and speed, for fast doors, increase

the value.

With incorrect direction of door movement: incorrect motor rotating field, switch off the control and swap the 2 motor connections.

2. Set the lower pre-limit switch so that it just triggers

Hörmann KG Verkaufsgesellschaft Page 14 of 30 HOE_FUH_GB.doc

TST Initial Operation TST FUH the CLOSED button, move the door to approx. 10 cm before closed position

IMPORTANT

The distance is very dependent on the door type and speed. For fast doors,

increase the value.

4. Set the lower limit switch so that it just triggers

IMPORTANT Do not overshoot limit switch in end positions!

5. Using the ¿ OPEN button, move the door to approx. 50 cm before open position

IMPORTANT The distance depends greatly on door type and speed. For fast doors, increase the value.

6. Set the upper pre-limit switch so that it just triggers.

7. Using the Ù OPEN button, move the door to approx. 10 cm before open position.

IMPORTANT The distance is very dependent on the door type and speed. For fast doors, increase the value.

8. Set the upper limit switch so that it just triggers

IMPORTANT Do not overshoot limit switch in end positions!

9. If necessary for the door type: Set EMERGENCY limit switch at top and bottom

Connect the NC contacts, e.g. in the safety circuit, in series with the thermal switch.

10. Press the Å STOP and ¿ OPEN buttons to skip to parameterisation mode. Select parameter P.980

«Service mode», open it, and set the parameter value «2» to «0» (automatic mode)

11. If required, correct the door OPEN and door CLOSED limit switch positions by fine-tuning the end positions in automatic mode.

To prevent door from moving unintentionally, only adjust the limit switches if

EMERGENCY OFF is activated or control is switched off !

12. Now, door may be moved in automatic mode.

6.3 Requesting new teach-in for limit stops

If electronic limit switches are used and the limit stop teach-in was done in advance, but the limit stops are not suited to the door, a new limit stop teach-in can be requested.

For this, the following parameters must be set:

P.210: 5 = New teach-in of all limit stops

TST

7 Further connection options

7.1 Photocell

Initial Operation TST FUH

7.2 External command controllers

Figure 11: Photocell connection

Figure 12: Connection for ext. command controllers

Hörmann KG Verkaufsgesellschaft Page 15 of 30 HOE_FUH_GB.doc Hörmann KG Verkaufsgesellschaft Page 16 of 30 HOE_FUH_GB.doc

TST

Overview of outputs

Initial Operation TST FUH

F202 1A

X11

L L1 L1 N N

X12

X13

T1 T2 T3

X14

X15

20 21 22

X16

30 31 32

230VAC

L,N,PE

U V W

PE

Red traffic light:

Flashes during door cycle and clearance phase

Green traffic light:

Relay active in

DOOR

OPEN position

Brake relay

TST Initial Operation TST FUH

Hörmann KG Verkaufsgesellschaft Page 17 of 30 HOE_FUH_GB.doc

The valid allocation of the inputs can be obtained in the switching documents!

Hörmann KG Verkaufsgesellschaft Page 18 of 30 HOE_FUH_GB.doc

TST Initial Operation TST FUH

P.989

-w

[Unit]

Adjustment range

0 … 1

Function Description/Notes

Start software update The update of the control software is started via the parameter. The update is started automatically when a USB stick is inserted and the file name tst_fuh.bin is found. A reset is carried out automatically after successful update.

You can also exit the Bootloader by performing a hardware reset.

9.2 Door cycle counter

P.000 rr

[Unit]

Adjustment range

[cycles]

Function

Cycle counter

Description/Notes

Shows door cycle counter

Illustration: 1234567

⇒ 1234. À actuate .567

Illustration: 67

⇒ 67

P.005 rr

P.973

-w

[Unit]

Adjustment range

[cycles]

0 … 1

Function Description/Notes

Maintenance counter The content of this parameter specifies the number of door cycles still to be run until the maintenance is due.

)

The setting -1 means that the maintenance counter has

Resetting the maintenance counter

not been activated yet.

The maintenance counter is acknowledged by setting this parameter to 1.

)

The hold-open phase that runs depends on the travel limit approached and the OPEN command used.

Each OPEN command can be set separately using the parameter P.5×4 as to if and which hold-open phase elapses.

(X = Number of the input used).

[Unit] Function

P.010 ww

Adjustment range

[sec.]

0 … 9999

P.011 ww

[sec.]

0 … 9999

Description/Notes

Hold-open phase 1 The door is held in the travel limit door OPEN position for the set time. Then, the closing is carried out automatically.

0 = Automatic closing deactivated

Hold-open phase 2 The door is held open in the travel limit intermediate stop/partial opening for the set time. Then, the closing is carried out automatically.

0 = Automatic closing deactivated

Hörmann KG Verkaufsgesellschaft Page 19 of 30 HOE_FUH_GB.doc

TST

P.015 ww

Initial Operation TST FUH

[Unit]

Adjustment range

[sec.]

0 … 200

Function Description/Notes

Minimum hold-open phase

Deviating from the hold-open phase 1 or 2, the door is held open for the minimum period of the set time. Then, the closing is carried out automatically.

9.5 Warning phase before door cycle/clearing time

P.025

-w

[Unit]

Adjustment range

[sec.]

0 … 20

Function Description/Notes

Warning phase before access

The door access is delayed by the time specified by this parameter after the input of a CLOSE command or after the hold-open phase (forced closing) has elapsed.

0 = Warning phase deactivated

P.210

-w

[Unit]

Adjustment range

0 … 5

Function Description/Notes

New teach-in of the limit stops

The teach-in for limit stops is restarted using this parameter.

The respective limit stops are moved to press-and-hold operation after activating the sequence and saved by keeping the stop button pressed.

The following setting possibilities are available:

0: Cancel, no limit stops have been taught in.

1: Teach-in of the limit switch down, limit switch up and, when required, limit switch intermediate stop.

2: Teach-in of limit switch up and, when required, limit switch intermediate stop are performed

3: Teach-in of limit switch down and limit switch up is performed.

4: Teach-in of intermediate stop limit switch is performed.

5: Teach-in of all limit switches and the rotating direction is performed.

)

Teach-in of the limit switch intermediate stop depends on the setting in parameter P.244

IMPORTANT

If the automatic adjustments of the pre-limit switches and limit switch bands are used (P.216 = 2), the parameters P.222 and P.223 are modified automatically.

The parameters are also modified when the driving speed or the inclination of the ramp are changed, as this leads to the restart of the automatic limit switch correction.

P.216 < 2 must be set if this ramp should be set manually.

9.7.1 Correct travel limit door CLOSE

Hörmann KG Verkaufsgesellschaft Page 20 of 30 HOE_FUH_GB.doc

TST

P.221 ww

Initial Operation TST FUH

[Unit]

Adjustment range

[Increment]

-125 … 125

Function Description/Notes

Correction value for door CLOSED

With this parameter, the entire lower travel limit is moved and therefore, the travel limit is moved together with the corresponding pre-limit switch.

The adjustment of the parameter value in the positive direction moves the travel limit upwards.

The adjustment of the parameter value in the negative direction moves the travel limit downwards.

9.7.2 Start of the CLOSE movement

P.350

-w

[Unit]

Adjustment range

[Hz]

6 … 200

Function Description/Notes

Operating frequency for fast CLOSE movement

Frequency specification for fast closing

(Operating frequency to lower pre-limit switch)

→ Adjust pre-limit switch, if necessary

ATTENTION: Observe closing force at safety strip!

IMPORTANT

If the automatic adjustments of the pre-limit switches and limit switch bands are used (P.216 = 2), the parameters P.232 and P.233 are modified automatically.

The parameters are also modified when the driving speed or the inclination of the ramp are changed, as this leads to the restart of the automatic limit switch correction.

P.216 < 2 must be set if this ramp should be set manually.

9.8.1 Correct travel limit door OPEN

P.231 ww

[Unit]

Adjustment range

[Increment]

-60 … 60

Function Description/Notes

Correction value for door OPEN

With this parameter, the entire travel limit door OPEN is moved and therefore, the travel limit is moved together with the corresponding pre-limit switch.

The adjustment of the parameter value in the positive direction moves the travel limit upwards.

The adjustment of the parameter value in the negative direction moves the travel limit downwards.

9.8.2 Start the opening

P.310

-w

[Unit]

Adjustment range

[Hz]

6 … 200

Function Description/Notes

Operating frequency for fast OPEN movement

Frequency specification for fast opening

(Operating frequency to upper pre-limit switch)

→ Adjust pre-limit switch, if necessary

Hörmann KG Verkaufsgesellschaft Page 21 of 30 HOE_FUH_GB.doc

TST Initial Operation TST FUH

9.8.3 Diagnostic display on the screen

Function

P.910

-w

[Unit]

Adjustment range

0 … 22 Display mode selection

Description/Notes

Using this parameter, the measurement variables at the bottom can be viewed direct in the door control display.

The following variables are displayed:

0: The control sequence is displayed (Automatic)

1: [Hz] Present driving speed

2: [A] Present motor current

3 [V] Present motor voltage

4: [A] Present intermediate current

5: [V] Present intermediate voltage

6: [°C] Present output stage temperature in °Celsius

7: [°F] Present output stage temperature in °Fahrenheit

8: [s] Present operating time of motor during last door cycle

9: [Increment] Present position

10: [Increment] Position of the reference

11: [Dig] Value channel 1 of the absolute encoder

12: [Dig] Value channel 2 of the absolute encoder

13: [V] Present reference voltage

P.920 rw

[Unit]

Adjustment range

1 … 10

Function

Error memory

Description/Notes

The control stores the last eight errors that have occurred in the error memory.

After jumping to parameter P.920:

— Switch to the level using membrane key OPEN/CLOSE

— Open the error memory using the STOP button

— Close the error memory using the STOP button

— Exit the parameter P.920 using Eb —

Eb1: Error message 1 (most recent error)

Eb2: Error message 2

Eb3: Error message 3

Eb4: Error message 4

Eb5: Error message 5

Eb6: Error message 6

Eb7: Error message 7

Eb8: Error message 8

Ebcl: Delete the complete error memory

Eb-: Exit, jump back to P.920

)

The display Er- means that no error has been entered.

Hörmann KG Verkaufsgesellschaft Page 22 of 30 HOE_FUH_GB.doc

TST Initial Operation TST FUH

9.10 Software version

P.925 rr

[Unit]

Adjustment range

Function Description/Notes

Software version The version of the current software used is displayed in this parameter.

9.11 Door operating time

P.930

-r

[Unit]

Adjustment range

[sec.]

Function Description/Notes

Operating time of the motor

The time required for the final movement is stored in this parameter.

9.12 Input voltage measurement

Function

P.940

-r

[Unit]

Adjustment range

[Volt] Input voltage

Description/Notes

The value of the present input voltage applied is displayed in this parameter.

9.13 Operating mode of the control

Function

P.980

-w

[Unit]

Adjustment range

0 … 5 Operating mode

Description/Notes

The operating mode of the control is set in this parameter.

The following modes are possible:

0: OPEN and CLOSE movement in press-and-release operation (Automatic)

1: OPEN movement in press-and-release operation,

CLOSE movement in manual mode (Semi-automatic)

2: OPEN and CLOSE movement in manual mode (Dead- man mode)

3: Dead man-mode emergency run

4: Fatigue testing with safety devices automatic OPEN and CLOSE movement. Before each new movement, a new hold-open phase P.010. is performed.

5: Fatigue testing without safety devices

)

The adjustment of the fatigue testing is lost when the control is switched off. Then the control is switched to manual mode.

Hörmann KG Verkaufsgesellschaft Page 23 of 30 HOE_FUH_GB.doc

TST Initial Operation TST FUH

9.14 Password

)

The passwords can be set on level 2

[Unit] Function

P.999

-w

Adjustment range

0 … FFFF Password

Description/Notes

The password enables the different parameter levels to be accessed.

IMPORTANT

The different password levels allow access to different numbers of parameters.

The parameters are not allowed to be modified without knowing their function.

To avoid errors and risks resulting from unauthorised access, passwords are only handed out to trained personnel.

9.15 Memory time for opening commands

Function

P.017

-w

[Unit]

Adjustment range

[sec.]

0 … 60

Memory time for

OPEN commands

Description/Notes

OPEN commands are saved for the time set here

)

The adjustment 0 means that OPEN commands are not saved.

10 Parameter overview

Function PAGE

counter

P.005 Maintenance counter

P.010 Hold-open phase 1

P.011 Hold-open phase 2

P.015 Minimum hold-open phase

P.017 Memory time for OPEN commands

P.025 Warning phase before access

P.210 New teach-in of the limit stops

P.221 Correction value for door CLOSED

P.231 Correction value for door OPEN

P.310 Operating frequency for fast OPEN movement

P.350 Operating frequency for fast CLOSE movement

P.910 Display mode selection memory version

P.930 Operating time of the motor

P.940 Input voltage

P.980 Operating

P.989 Start software update

P.999 Password

Ex factory Modified by: on:

ND [cycles]

5 [sec.]

10 [sec.]

3 [sec.]

60 [sec.]

0 [sec.]

0 [Increment]

65 [Hz]

30 [Hz]

ND [sec.]

ND [Volt]

Hörmann KG Verkaufsgesellschaft Page 24 of 30 HOE_FUH_GB.doc

TST Initial Operation TST FUH

11 Overview of messages

If errors do not reset themselves, they may be acknowledged.

Before the corresponding message is acknowledged, the cause of the error must be eliminated.

To do this, press the Å STOP button and hold it down, then press the EMERGENCY-OFF button.

Alternatively, you can also press the Å STOP button for approx. 5 seconds.

F.000

F.005

Door position outside top

Door position outside bottom

Incorrect travel limits

• Parameter value for top emergency limit switch is too small

• Upper limit switch range (limit switch band) is too small

• Mechanical brake is defective or incorrectly set

• Parameter value for bottom emergency limit switch is too small

• Lower limit switch range (limit switch band) is too small

• Mechanical brake is defective or incorrectly set

F.020

F.021

F.030

F.031

F.043

Implausible door operation

Operating time exceeded

(during opening, closing or dead-man)

Testing of the emergency opening failed

Contouring error (change in position of door is less than expected)

Detected direction of rotation differs from the expected direction of rotation

Malfunction of photocell’s prelimit switch

• Current motor operation time has exceeded set maximum operation time; door may be sluggish or blocked.

• If mechanical limit switches are used, one of the limit switches did not engage

• The max. permissible runtime during the testing period has been exceeded.

• Call service department

• Door or motor is blocked

• Power too low for starting torque insufficient

• Mechanical limit switch was not passed or is defective

• Fixing to shaft of absolute encoder is not tightened

• Wrong positioning system selected (P.205)

• When using increment encoders: Channel A and B have been swapped

• Motor’s direction of rotation was switched compared to calibration

• Too much «sagging» when door starts to move, brake releases too soon, or torque is too low, boost may need to be adjusted.

• The photocell’s pre-limit switch remains engaged also at centre travel limit or upper travel limit.

F.060

Operator call crash system

The control cabinet has just been switched on or the rubber bottom part has been hit

Reset procedure, see:

• Fitting diagram

•

Control cabinet door outside

F.080

Maintenance counter is exceeded

Malfunction: Maintenance is required

• Service counter has run down

F.090

Control is not parameterised

Parameter is not set

• The basic parameters (P.205, P.100 to P.103) of control

TST FUS have not been set.

Hörmann KG Verkaufsgesellschaft Page 25 of 30 HOE_FUH_GB.doc

TST Initial Operation TST FUH

F.201

F.211

F.212

External emergency-off 1 activated

External emergency-off 2 activated

Safety chain malfunctions

Internal emergency-off

«mushroom button» activated or watchdog (processor monitoring)

• Emergency stop chain was interrupted at the «internal emergency-off“ input, but parameterisation mode was not selected

• Internal parameter or EEPROM tests failed. Activate the

STOP membrane key for more information on the cause

• Emergency stop chain interrupted at emergency-off input

F.360

F.361

F.362

F.363

F.364

F.365

F.366

F.369

F.385

F.3A1

F.3B1

F.3C1

Malfunction of the safety contact strip

Short circuit detected at strip input

Set limit for number of strip activations during closing has been reached

Redundancy error at short circuit

• Line short detected in strips with NC contacts

• Parameterised, maximum number of safety strip triggerings during a door cycle has been exceeded

Interruption at strip input

Safety strip – Testing failed.

Redundancy error at interruption

Impulse frequency too high for optical safety strip

• One of the evaluator channels for short circuit recognition does not respond identically to the second channel. Æ Control unit print defective

• Dynamic optical system connected but not set in parameter P.460.

• Connecting cable defective or not connected.

• Terminating resistor defective or missing. set

• Testing request did not activate safety strip as expected.

• The time period between testing request and testing is not adjusted.

• One of the evaluator channels for interruption recognition does not respond identically to the second channel.

Æ Control unit print defective

• Dynamic optical system connected but not set in parameter P.460.

• Defective optical safety strip

• Defective input for internal safety strip.

Internal safety strip parameterised incorrectly

Malfunction of safety strip’s pre-limit switch

• An internal safety strip is connected but deactivated.

Number of activations exceeded, safety A

Number of activations exceeded, safety B

Number of activations exceeded, safety C

• Pre-limit switch for safety switch deactivation, and/or reversal after safety switch activation, remains engaged also at upper travel limit.

• Parameterised maximum number of activations of safety A during one door cycle has been exceeded

• Parameterised maximum number of activations of safety B during one door cycle has been exceeded

• Parameterised maximum number of activations of safety C during one door cycle has been exceeded

Hörmann KG Verkaufsgesellschaft Page 26 of 30 HOE_FUH_GB.doc

TST Initial Operation TST FUH

F.400

Hardware reset of control recognised

General hardware error

• Severe malfunctions in the supply voltage

• Internal watchdog has activated

F.401

F.40A

F.410

Watchdog error

Software exception

Overload current

(Motor current or intermediate circuit)

• Internal watchdog has activated

F.420

F.425

F.426

F.430

F.435

F.440

F.510

F.515

F.519

F.520

F.521

Overload in intermediate circuit

Limit 1

Mains overvoltage

Mains undervoltage

Heat sink temperature is outside operating range

Limit 1

Malfunction: Temperature in housing rising above 75 °C

Overload current in intermediate circuit

Limit 1

Overload current in motor/intermediate circuit

Limit 2

Motor protection function has recognised overload current

IGBT driver module has recognised overload current.

Overload in intermediate circuit

Limit 2

Undervoltage in intermediate circuit

• Incorrect nominal specifications set for motor (P100 –

P103)

• Voltage increase/boost set not adjusted (P140 or

P145)

• Motor incorrectly dimensioned for door used

• Door is sluggish

• Brake chopper malfunctioning/defective/not present

• Supply voltage much too high

• The motor feeds too much energy back during generation operation, the kinetic energy of the door can not be sufficiently reduced.

• The supply voltage of the control is too high

• The supply voltage of the control is too low

• Load on output stage or brake chopper too high

• Ambient temperature too low for control operation.

• Output stage clock frequency too high (parameter

P.160

)

• Load on frequency converter/switching too high

• Control box not sufficiently cooled

• Set voltage increase («boost») not adjusted

• Motor incorrectly dimensioned for door used

• Door is sluggish

• Incorrect nominal specifications set for motor (P100 –

P103)

• Voltage increase/boost set not adjusted (P140 or

P145)

• Motor incorrectly dimensioned for door

• Door is sluggish

• Incorrect motor characteristic curve (motor nominal current) set (P101)

• Voltage increase/boost set too high (P140 or P145)

• Motor incorrectly dimensioned

• Short circuit or earth contact at motor terminals

• Motor nominal frequency set extremely incorrectly

(P100)

• Voltage increase/boost extremely excessive (P140 or

P145)

• Motor incorrectly dimensioned

• Motor winding defective

• Brief interruption of emergency-off circuit.

• Brake chopper malfunctioning/defective/not present

• Input supply voltage too high

• The motor feeds too much energy back during generation operation, as it needs to reduce the kinetic energy of the door.

• Input supply voltage too low, usually with load

• Load too high/output stage or brake chopper

Hörmann KG Verkaufsgesellschaft Page 27 of 30 HOE_FUH_GB.doc

TST Initial Operation TST FUH

F.524

F.525

F.530

F.535

F.540

General hardware error

malfunction

External 24 V supply missing or too low

Overvoltage at the power input

Heat sink temperature

Operating range

Limit 2

Malfunction: Temperature in housing rising above the critical 80 °C

Overload current in intermediate circuit

Limit 2

• Overload, but no short circuit.

• If the 24 V short circuits, the control supply does not switch on and the V 306 glow lamp lights up.

• The supply voltage is too high

• The supply voltage has a high fluctuation

• Load on output stage or brake chopper too high

• Clock frequency of output stage too high (P160)

• Ambient temperature of control too low

• Internal temperature too high

• Set voltage increase («boost») not adjusted

• Motor incorrectly dimensioned for door used

• Door is sluggish

F.700

F.752

F.760

F.762

Error in positioning system

Position detection defective

For mechanical limit switches:

• At least one limit switch does not correspond to parameterised active status.

• An implausible combination of at least 2 active limit switches.

For electronic limit switches:

• After factory parameter activation was called up

(parameter P.990), the corresponding positioning

Timeout during log transfer system was not parameterised.

• Calibration is incomplete or defective and must be repeated.

• The intermediate travel limit, when activated, is implausible.

• Synchronisation not completed or reference switch defective

• Interface line defective/interrupted

Position is outside range area

Electronic limit switch positions are incorrect

• Evaluation electronics of absolute encoder are defective

• Defective hardware or severely malfunctioning environment

• Shield connection cable

• Fit RC module (100 Ω + 100 nF) to brake

• Position sensor operator defective

• Evaluation electronics of absolute encoder are defective

• Defective hardware or severely malfunctioning environment

• Upper limit switch Eo or intermediate limit switch E1 has exceeded the valid limit range

• Control has not been initialised

• Position specifications incorrect during calibration, or values no longer plausible

11.1 Internal system-induced errors F.9xx

These errors are internal errors which cannot be eliminated by the person operating the control.

If this type of error occurs, please contact customer service immediately.

Hörmann KG Verkaufsgesellschaft Page 28 of 30 HOE_FUH_GB.doc

TST Initial Operation TST FUH

General messages

STOP

_Eu_

≡Eu≡

Stop

/reset status, waiting for the next entered command

Lower limit switch Eu

Lower travel limit locked

→ No opening possible (e.g. air lock)

Active closing

Z[email protected]

-Eo-

≡Eo≡

Upper travel limit Eo

Upper travel limit locked

→ No closing possible (e.g. safety loop)

@OPEN

Active opening

-E1-

Centre travel limit E1 (intermediate travel limit)

≡E1≡

FAIL

EICH

Centre travel limit locked

→ no closing possible (e.g. safety loop)

Malfunction

→ Only dead-man operation possible, and possibly automatic opening

Calibration

→ Setting the travel limits in dead-man operation

(With absolute encoder)

→ Begin process via STOP button

≡NA≡

NOTF

‘Hd’

Emergency-off

→ No door operation possible, hardware safety chain interrupted

Emergency operation

→ Dead-man operation, ignores all safety devices, etc.

Manual

→ Dead-man operation

ParA

SYNC

‘Au’

‘Hc’

FUS

Parameterisation

Synchronisation

(Incremental position sensor/limit switch

→ unknown position)

Automatic

→ Designates change of status from «Manual» to «Automatic»

Semi-automatic

→ Marks the change from»Manual mode» to «Automatic mode»

First display after switching on (power up and self-test)

Status messages during calibration

E.i.E.u.

Request for calibration of lower travel limit (in dead-man operation)

E.i.E.o.

Request for calibration of upper travel limit (in dead-man operation)

E.i.E.1.

Calibration of intermediate travel limit E1 (in dead-man operation)

Hd.cL

Hd.oP

Hd.Eu

Hd.Eo

Hd.Ao

I.023

I.080

I.100

I.150

I.160

I.161

I.170

I.180

I.185

I.199

I.200

I.201

I.202

I.203

I.205

I.210

I.211

I.310

I.360

Status messages during dead-man operation:

Dead-man closing (membrane key: CLOSE)

Dead-man opening (membrane key: OPEN)

Lower travel limit has been reached, no further dead-man closing possible

Upper travel limit has been reached, no further dead-man opening possible

Outside the permitted Eo position (no dead-man opening possible)

Information message during automated operation:

Emergency opening message released

Maintenance will be necessary soon/service counter will run down soon

Speed too high when upper travel limit is reached

Speed too high when lower travel limit is reached

Permanent OPEN still active

Open command encoder priority active, close movement only with a command encoder that has the same priority (see p.5 x 4)

Safety opening is being carried out

Wait for the command of the membrane keypad

Waiting for acknowledgement (service request), display flashing

Door cycle counter implausible (re-initialise

→ parameter)

Reference position corrected or recognised (after calibration)

Reference position re-initialised

Reference position missing

Reference position incorrect

Synchronisation

Upper pre-limit switch implausible

Lower pre-limit switch implausible

OPEN command is transmitted to door 2

Malfunction of the safety strip (opener) during the last closing, the message is deleted after the close position has been reached without malfunctions

Hörmann KG Verkaufsgesellschaft Page 29 of 30 HOE_FUH_GB.doc

TST Initial Operation TST FUH

I.365

I.500

I.501

I.502

I.505

I.506

I.507

I.510

I.515

I.520

I.555

I.901

I.902

I.903

I.904

I.905

I.906 noEr

Er—

Prog

Malfunction of the safety strip (closer) during the last closing, the message is deleted after the close position has been reached without malfunctions

Upper limit switch is being corrected

Upper pre-limit switch is correct

Upper limit switch band is correct

Lower limit switch is being corrected

Lower pre-limit switch correct

Lower limit switch band correct

Limit switch correction complete

Control is preparing automatic teach-in of limit switches

Max. speed during the automatic limit switch correction has not been reached.

Limit switch correction is being carried out

Waiting for USB stick

The update file could not be found on the stick (the file with the name tst_fuh.bin should be in the root directory)

File cannot be opened

ROM will be deleted

ROM is being programmed

Update file has an incorrect format (not implemented yet)

Information messages during the parameterisation:

Error memory: no error stored

Error memory: error is found without a corresponding message

Programming message during execution of original parameters or default set.

General inputs

E.000

OPEN button on membrane keypad

E.050

STOP button on membrane keypad

E.090

CLOSE button on membrane keypad

E.101

Input 1 : see wiring diagram

E.102

Input 2 : see wiring diagram

E.103

Input 3 : see wiring diagram

E.104

Input 4 : see wiring diagram

E.105

Input 5 : see wiring diagram

E.106

Input 6 : see wiring diagram

E.107

Input 7 : see wiring diagram

E.108

Input 8 : see wiring diagram

E.109

Input 9 : see wiring diagram

E.110

Input 10 : see wiring diagram

E.121

Input 21 : Reserve

E.128

Input 28 : Reserve

Safety/emergency stop chain

E.201

Internal emergency-off «mushroom button» activated

E.211

External emergency-off 1 activated

E.212

External emergency-off 2 activated

General safety strip

E.360

Activation of internal safety strip

Radio control plug-in module

E.401

Radio control channel 1

E.402

Radio control channel 2

Induction loop evaluator plug-in module

E.501

Detector channel 1

E.502

Detector channel 2

Internal inputs

E.900

Fault signal from drive module

Hörmann KG Verkaufsgesellschaft Page 30 of 30 HOE_FUH_GB.doc

Hörmann KG Verkaufsgesellschaft

D-33803 Steinhagen

Operating instructions induction loop detector plug-in card for control panels

TST SUVEK1 — 1-channel detector

TST SUVEK2 — 2-channel detector

50.0 mm

Service

CH 1

green

LED

red

Sensitivity b

Sensitivity a

Holdingtime

Frequency

Sensitivity b

Sensitivity a

Holdingtime

Frequency

CH 2

green

LED

red

Loops

O N

X 5

X 2

X 1

Please read the operating- and safety instructions thoroughly before putting the traffic detector into operation !

1 General

Characteristic features:

The induction loop detector TST SUVEK1/2 is a system for inductive detection of vehicles with the following characteristic features:

•

evaluation of 1 (TST SUVEK1) or 2 (TST SUVEK2) loops

•

galvanic separation between loop and detector electronics

•

automatic system alignment immediately after activation

•

continuous resetting of frequency drifts

•

no mutual influence of loops 1 and 2 by multiplex processes on

TST SUVEK2

•

sensitivity is independent of loop inductivity

•

occupied-message on LED-display

•

open-collector outputs, galvanically separated by optocouplers

•

additional, looped-through I/O, galvanically separated by optocouplers

•

indication of loop frequency via LED

•

diagnosis possibility in connection with diagnostic unit VEK FG2

HOE_SUVEK02.doc

2 Possibilities of adjustment

2.1 Sensitivity

By adjusting the sensitivity, you determine a change of inductivity for each channel, which a vehicle has to cause in order to set the appropriate output of the detector.

Sensitivity adjustment is done separately for each channel with the help of 2 DIP-switches.

Sensitivity level Channel 1: DIP-switch 1, 2

Channel 2: DIP-switch 5, 6 *)

1 low (0,27%

∆ f/f)

OFF/OFF

2 (0,09%

∆ f/f)

ON/OFF

3 (0,03%

∆ f/f)

1 8

OFF/ON

4 high (0,01%

∆ f/f)

2.2 Holding time

The holding time can be adjusted with the help of DIP-switches 3 and

7. After the holding time has expired, a «loop free» signal is emitted, followed by an automatic rebalancing of the loops. The holding time starts as soon as the loop is seized.

Holding time

ON/ON

Channel 1: DIP-switch 3

Channel 2: DIP-switch 7 *)

5 minutes

OFF infinite

1 8

2.3 Frequency adjustment and rebalancing

The actual frequency of the detector can be adjusted in two levels with the help of DIP- switches 4 and 8.

Frequency Channel 1: DIP-switch 4

Channel 2: DIP-switch 8 *)

low

1 8

OFF high

1 8

The admissible frequency range is 30kHz to 130kHz. The frequency depends on the loop geometry, number of turns, inductivity resulting from the loop supply line and the chosen frequency level.

A rebalancing can be manually triggered by changing the frequency adjustment of a channel.

As soon as switched on, the detector automatically carries out an adjustment of the loop frequency. In case of a short-term voltage loss of <0,1s no rebalancing will take place.

3 Connections

Connection

X1 / 1

X1 / 2

X1 / 3

X1 / 4

X1 / 5

X2 / 1

X2 / 2

X2 / 3

X2 / 4 — X2 / 5

X5 / 1 — X5 / 2

X5 / 3 — X5 / 4

Type

Supply

Optocoupler

GND

24V DC

GND

Optocoupler-outp. Channel 2 *)

Optocoupler-outp. Channel 1 add. optocoupler output add. optocoupler input outp. 24V DC (connect. X1 / 2)

—

Loop channel 1

Loop channel 2 *)

*) nur TST SUVEK2

Notice: GND-pin X1 / 1 has to be connected externally with PE !

15.12.04

4 Outputs and LED-display

4.1 Outputs

Signal indication is done via optocoupler-outputs pin 4 and 5 at plug

X1. GND-reference is X1 pin 3.

Optocoupler-outp. 1/2

high

Detector conditions

Loop free / Reset / rebalancing low Loop occupied / loop fault

4.2 LED-display

The green LED indicates that the detector is operable. The red LED indicates activation of the relay output in dependence on the seizure condition of the loop.

Green LED

Loop

Red LED

Loop Detector condition

off flashes on on off off off on

No supply voltage

Alignment or frequency indication

Detector ready, loop free

Detector ready, signal indication off on Loop fault

4.3 Indication of loop frequency

Approx. 1 s after the detector has been aligned, the loop frequency is indicated via flash signals of the green LED. First, the 10kHz-digit is indicated. In steps of a loop frequency of 10kHz, the green LED of the detector channel will flash one time. After a break of 1s , the

1kHz-digit is indicated in the same way. If the units digit has the significance of ‘0’, 10 flash signals will be emitted. The 1kHz-flash signals will be a little shorter than those of the 10kHz-digit.

Example of a loop frequency of 57 kHz:

tens

5x 10kHz

5 Technical data

units

7x 1kHz

Dimensions

Protection class

Current supply

Slow operation

Signal duration

72,5 x 50 x 18 mm (LxWxH without plug)

IP 00

24V DC

20% max. 2,0W

Working temperature

-20 °C to +70 °C

Storage temperature

-20 °C to +70 °C

Air moisture

Loop inductivity

Frequency range

Sensitivity

Holding time

Loop lead in

Loop resistance

Optocoupler output

max. 95 % non-thawing

20-800 µH, recommended 75-400uH

30-130 kHz in 2 levels

0,01 % to 0,27 % (

∆ f/f) in 4 levels

0,02 % to 0,54 % (

∆

L/L)

5 min. or infinite max. 100 m max. 20 Ohm (incl. supply line)

45V / 10mA / 100mW

50ms TST SUVEK1, 100ms TST SUVEK2

> 200 ms

Fall-delay time

Connection

25ms TST SUVEK1, 50ms TST SUVEK2

2x MOLEX-socket, series 3215, 5-pole

1x plug-in terminal, 4-pole, RM 3,81

CE- standards

EN 61000-6-2, March 2000

EN 50081-1, March 1993

6 Safety instructions

•

The appliance may only be used for the purpose intended by the manufacturer.

•

Please hand out the operating instructions to all users and keep i in an easily accessible place.

•

Unacceptable changes as well as the use of spare parts and special features which are not sold or recommended by the manufacturer of the appliance, may cause fire, electric shocks and injuries. Therefore, such measures lead to nonliability of the manufacturer and a lapse of all warranty claims.

•

The appliance is subject to the manufacturer’s guarantee regulations in the version valid at the time of purchase. We canno be held liable for improper or faulty manual or automatic adjustmen of parameters resp. improper use of the appliance.

•

Repair work may only be carried out by the manufacturer.

•

Installation, initiation, maintenance, measuring and adjustment o the traffic detector should only be carried out by electricians with a good knowledge of the rules for prevention of accidents.

•

When handling appliances that come into contact with electricity the valid VDE-regulations have to be observed. In particular, these are (list may be incomplete): VDE 0100, VDE 0550/0551, VDE

0700, VDE 0711, VDE 0860, VDE 0105 as well as the rules for the prevention of accidents and fire, VBG4.

•

All labour that is carried out on the appliance as well as its initiation, has to conform to the national as well as the local electric regulations.

•

The user has to make sure that the appliance is installed and operated according to the technical rules of the country o installation as well as other regional regulations. Cable dimensions protection, grounding, disconnection, insulation control and excess current protection should be especially considered.

•

According to machine directive 89/392/EWG, appendix IV, as wel as directive ZH1/494 of the German employer’s liability insurance association, the appliance must not be used as a safety

component. Systems with a high danger potential need additiona safety contrivances!

Notice

The indications made in these operating instructions may be altere without previous notice.

With the edition of these instructions, all previous editions becom void.

Composition of the information given in this manual has been done t the best of our knowledge. Hörmann KG Verkaufsgesellschaftdoe not guarantee the correctness of the details given in thes instructions and may not be held liable for damages ensuing from incorrect installation.

Since, despite all our efforts, errors may not be completely avoided we are always grateful for your useful tips.

The installation instructions given in this manual are based o advantageous boundary conditions.

Hörmann KG

Verkaufsgesellschaftdoes not give any guarantee promise for perfec function of the traffic detector in cross surroundings.



Technische Mitteilung TM-EL19

Verteiler : Gruppe A, B, C, D, E, F

.-.-.-.-.-.-.-.-.-.-

Wichtige Hinweise

Handsender gehören nicht in Kinderhände!

Handsender dürfen nun von Personen benutzt werden, die in die Funktionsweise der ferngesteuerten

Toranlage eingewiesen sind! Die Benutzung der Fernsteuerung muss mit Sichtkontakt zum Tor erfolgen! Die

Programmierung der Fernsteuerung ist immer in der Garage in Antriebsnähe vorzunehmen! Für die

Inbetriebnahme der Steuerung sind ausschliesslich Originalteile zu verwenden!

• Die Geräte sind vor direkter Sonneneinstrahlung zu schützen!

• Die Handsender sind vor Feuchtigkeit und Staubbelastung zu schützen!

Bei Nichtbeachtung kann durch einen Feuchtigkeitseintritt die Funktion beeinträchtigt werden!

Zulässige Umgebungstemperatur : -20

Die örtlichen Gegebenheiten können Einfluss auf die Reichweite der Fernsteuerung haben!

Erweitern der Fernsteuerung mit weiteren Handsendern HS-SEU1, HS-SEU2, HS-SEU4 oder HS-SEU6

Hinweis : Ist kein seperater Zugang zur Garage vorhanden, so ist jede Änderung oder Erweiterung von

Programmierungen innerhalb der Garage durchzuführen. Bei der Programmierung und Erweiterung der

Fernsteuerung ist darauf zu achten, dass sich im Bewegungsbereich des Tores keine Personen und

Gegestände befinden.

1. Der Sender, der den Code „vererben“ soll (Vererbungssender) und den Sender, der den Code lernen soll (Lernsender), direkt nebeneinander halten.

2. Die gewünschte Taste des Vererbungssenders drücken und gedrückt halten. Die LED des

Vererbungssenders leuchtet nun kontinuierlich.

3. Sofort danach die gewünschte zu lernende Taste des Lernsenders drücken und gedrückt halten – die

LED des Lernsenders blinkt zuerst für 4 Sek. langsam und beginnt bei erfolgreichem Lernvorgang schneller zu blinken.

4. 4. Die Tasten vom Vererbungssender und vom Lernsender loslassen.

Eine Funktionsprüfung durchführen! Bei einer Fehlfunktion die Schritte 1 – 4 wiederholen.

Achtung! Während des Lernvorganges kann bei Betätigung des Vererbungssenders eine Torfahrt ausgelöst werden, wenn sich ein darauf programmierter Empfänger in der Nähe befindet!

Hinweis : Wenn während des langsamen Blinkens die Taste des Lernsenders losgelassen wird, wird der

Lernvorgang abgebrochen.

Hörmann KG Verkaufsgesellschaft D-33803 Steinhagen

Technical Bulletin TM-EL19

Author : Michael Lienenkämper

Distribution

: Gruppe A, B, C, D, E, F

.-.-.-.-.-.-.-.-.-.-

Important

Keep hand transmitters out of reach of children at all times!

Hand transmitters should only be used by persons who know to operate the remote controlled door system.

Only use the remote control when the door is in your line of vision! Always programme the remote control inside the garage near the door operator. When putting the remote control into operation, use original components only!

• Protect equipment from direct sunlight.

• Protect hand transmitters against dampness and dust.

If damp is allowed to penetrate through non-observance of the above, the function of the unit can be seriously impaired.

Temperature range : -20

Local conditions may affect the range of the remote control.

Extending the remote control set by adding further hand transmitters HS-SEU1, HS-SEU2,

HS-SEU4 or HS-SEU6

Note : If the garage does not have a seperate entrance, you should carry out any programming alterations or expansion inside the garage. When programming or expanding the remote control set, ensure that no persons or objects are within the door`s range of movement.

1. Hold the transmitter which is to „teach“ the code (teaching transmitter) and the transmitter which is to learn the code (learning transmitter) directly alongside each other.

2. Press and hold the desired button on the teaching transmitter – the LED on the teaching transmitter now glows continuously.

3. Immediately after having done this, press and hold the button which is to learn on the learning transmitter – the LED on the learning transmitter initially flashes slowly for about 4 seconds, but then starts flashing more rapidly once the learning procedure has been successfully completed.

4. Release the buttons on the teaching transmitter and learning transmitter.

Check that the transmitters are functioning correctly. If not, repeat steps 1 – 4.

CAUTION! Activation of the teaching transmitter during the learning procedure could set the door in motion if there is an appropriately programmed receiver near to where you are standing!

Note : The learning procedure will be aborted if you release the button on the learning transmitter during the slow-flashing period.

Hörmann KG Verkaufsgesellschaft D-33803 Steinhagen

Technische Mitteilung TM-EL20

Verteiler : Gruppe A, B, C, D, E, F

.-.-.-.-.-.-.-.-.-.-

Hinweis : GSM900 Handys können bei gleichzeitiger Benutzung die Reichweite der Funkfernsteuerung beeinflussen.

1. Die rote Taste (Programmiertaster) am Empfänger kurz betätigen – die rote LED beginnt langsam zu blinken.

2. Die gewünschte zu programmierende Taste des Handsenders mindestens 1 Sek. drücken. Der Abstand zwischen dem Sender und dem Empfänger muss min. 1m betragen.

3. Bei erfolgter Programmierung beginnt die rote LED im Empfänger schneller zu blinken.

4. Die Taste des Handsenders loslassen.

Nach Beendigung des Blinkens ist der Empfänger empfangsbereit.

Zur Überprüfung ist die programmierte Taste des Senders zu betätigen, die rote LED des Empfängers leuchtet auf.

Hinweis : Wenn 30Sek. nach Druck auf den Programmiertaster keine Programmierung erfolgt, erlischt die langsam blinkende rote LED im Empfänger wieder.

Abbrechen der Programmierung : Wenn der Programmiertaster 3-mal kurz innerhalb von 2 Sek. betätigt wird, erlischt die rote LED und der Programmiervorgang wird abgebrochen.

Empfang : Wenn der Empfänger die Sendecodes empfängt, wird der Signalausgang für 0,5 Sek. aktiv.

Während dieser Zeit leuchtet die LED am Empfänger.

„P“-Taste

Technical Bulletin TM-EL20

Author : Michael Lienenkämper

Distribution

: Gruppe A, B, C, D, E, F

.-.-.-.-.-.-.-.-.-.-

Note : GSM 900 mobile phones used at the same time may influence the range of the radio remote control.

1. Briefly press red button „P“ (programming button) on the receiver – the red LED starts flashing slowly.

2. Press the button you wish to programme on the hand transmitter for at least 1 second. The distance between the transmitter and the receiver should be at least 1m.

3. When the programming has been completed, the red LED starts flashing more rapidly.

4. Release the button on the hand transmitter.

Once the flashing stops, the receiver is ready for operation.

To test the function, press the programmed button on the transmitter – the red LED lights up when the output is active.

Note : If no programming is carried out within 30 seconds of processing the „P“-button, the slow flashing red

LED on the receiver goes out again.

Aborting the programming procedure : If after pressing the programming button this is pressed 3 times within 2 seconds, the red LED goes off and the programming procedure is aborted.

Reception : When the receiver receives the transmitting codes that were programmed the signal output is active for 0,5 seconds. During this time the LED on the receiver is on.

„P“-button

Hörmann KG Verkaufsgesellschaft D-33803 Steinhagen Hörmann KG Verkaufsgesellschaft D-33803 Steinhagen

W i r e l e s s I m p u l s e T r a n s m i s s i o n

T e c h n i c a l D a t a

1. Failure Diagnosis

1.1. OPT-CF 1163

HOE_OPTOC_GB.DOC

YELLOW Condition Test

— wiring to control panel active

1 s

2 s inactive safety edge activated crash or missing light transmission

— wiring to control panel

4 Hz

— wiring of safety edge

— mounting of safety edge

— alignment (straight way of light)

— optical axis interrupted

— dirt

— batteries OPT-CM 1163

— wiring to control panel no operating voltage

RED condition Action

— change OPT-CF 1163

— none

Hörmann KG Verkaufsgesellschaft D-33803 Steinhagen Hörmann KG Verkaufsgesellschaft

W i r e l e s s I m p u l s e T r a n s m i s s i o n

T e c h n i c a l D a t a

YELLOW Condition

R F

2 s

R F

— none

Action

RED condition Action

— change OPT-CM 1163

— none

D-33803 Steinhagen

OPTOC_BAT.DOC

Источник

BK150FUEH

BK150FUEH
014634 GB
24.08.2009
Hörmann KG Verkaufsgesellschaft
D-33803 Steinhagen
1. S400 -> „ON“
2.
3.
4.
5.
6.
7.
8.
LIDL / V2012
V5015SE/ V5030SE / V6030SE
V2715SER
V3009
V2515FoodL
9.
V3515Iso
H3530
V6020TR
Turboflex V4530
P991
5
6
7
8
10.
11.
12.
14.
15.
16.
P991
0
1
2
3
4
13.
17. S400 -> „OFF“
HOE_PROFILANLEITUNG.DOC
21. Jul. 2009
•Commissioning Of Mainboards With
Integrated Frequency Inverter And DES
Commissioning The Door
Enter Programmig mode!
mode!
• Are all components connected with correct
polarity?
polarity?
• E.i.E.u.
E.i.E.u. blinks fast to set the fully close position
in dead man mode.
mode. To save press and hold stop until
the display changes to a slower blinking
• Then the 7 segment display will blink
E.I.C.H after switching on the panel.
panel.
• Door end positions can be set by foil key pad
now.
now.
• E.i.E.o. . Now set the fully open position.
position. Also
in dead man mode.
mode. Saving is also done by
continuously pressing the STOPSTOP-push button.
button.
• If E.I.C.H. blinks the programming
procedure starts briefly pressing STOP.
• The display now changes to -EoEo-. The door can
already be used in automatic mode within the set
limits.
limits.
E.I.C.H. won´
won´t blink?
blink?
• No problem!
problem! Switch off panel with mains switch.
switch. Wait until
display goes off,
off, open control panel and set the single DILDILswitch in the right part of the mainboard to the „ON“
ON“
position.
position. Now push the emergency stop button and switch on
the panel again.
again.
• The display now showsP000
showsP000 and is in the programming
mode.
mode. Choose parameter P999.
P999. with the arrow keys on the
foil key pad.
pad. Briefly press STOP and change the displayed
value from 1 to 2, press STOP until the dot stops blinking.
blinking.
The display changes back to P000 again.
again.
• Choose parameter P210 , briefly press stop and increase the
displayed value from 0 to 3.
• Press STOP and hold until the dots stop blinking.
blinking.
Corrections necessary?
necessary?
• Press the emergency stop button.
button. The display shows
P000 in the programming mode.
mode.
• To correct the end limit open position choose
parameterP231
parameterP231,, for crrection of the end limit close
choose P221 .
• Briefly press STOP and set correction values.
values. Don´
Don´t
forget to save by continuously pressing STOP until the
dots stop blinking!
blinking!
• Pull out the emergency stop button and continue as said
before.
before.
Test Correction Values Now!
Now!
• Pull out the emergency stop button and test the end
limit positions.
positions.
• If the end limits still are not ok correct again.
again.
• Corrections ok and programming done?
done? Switch off the
control panel and wait for the display going off,
off, set
DILDIL-switch back to the „OFF“
OFF“ position,
position, switch on
again and ...
•(GB)
It Functions!!
Functions!!
• As it is ment to do.
do.
• If still problems occure that you cannot fix
with the documentation give us a call.
call.
•
P.S.: ... Up to here all items will be found in the operation manual that is part of the wiring
diagram...
diagram...
8.2a
8.2b
W1 W2
(W51)
W5
W5
W4 W3
8.2c
W3
W4
W5
W2 (W51)
W1
1
V 5015 SE / V 5030 SE
V 6030 SE
1
2a
2
3
2b
2b
2a
4
3
4
V 2715 SE R
1
0
2
3
4
5
6
7
8
9
SEUE001D.F26 / LIE / 12.04.2007
BK 150 FUE H (HS) / BS 150 FUE H (VA)
SoftEdge
H28-283
wiring diagramme
adjustment instructions
GB
main supply
connecting lead
control voltage
year of manufacture
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
230V / 50Hz
min. 3x2,5mm²
24V DC
2008ff
2
Subject to technical changes!
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
title page
H28-283
=
+
Gesamt
Blatt
22
1
1
0
2
3
4
Table of contents
Page
5
6
7
8
Spalte X: eine automatisch erzeugte Seite wurde manuell nachbearbeitet
Page name
additional page field
9
SEUJ005D.F06/LIE/12.04.2007
date
person in charge
X
1
title page
24.08.2009
ws21
2
contents
24.08.2009
ws21
3
mains supply
24.08.2009
TW
4
impulse generator
24.08.2009
TW
5
contact bar
24.08.2009
TW
6
photocells
24.08.2009
TW
7
output module
24.08.2009
ws21
8
radar (optional)
24.08.2009
ws21
9
option
24.08.2009
TW
10
option
24.08.2009
TW
11
DES
24.08.2009
TW
12
terminal connection diagramme X13
24.08.2009
ws21
X
13
terminal connection diagramme X14
24.08.2009
ws21
X
14
terminal connection diagramme X15
24.08.2009
ws21
X
15
terminal connection diagramme X21A
24.08.2009
ws21
X
16
terminal connection diagramme X21B
24.08.2009
ws21
X
17
connection diagramme X3
24.08.2009
ws21
X
18
connection diagramme X3.1
24.08.2009
ws21
X
19
connection diagramme X3.2
24.08.2009
ws21
X
20
cable overview
24.08.2009
ws21
X
X
21
parts list
24.08.2009
ws21
X
22
parts list
24.08.2009
ws21
X
1
3
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
contents
H28-283
=
+
Gesamt
Blatt
22
2
1
0
2
3
4
5
6
7
8
9
circuit board
Technical connection requirements, including those from the
local energy supplier, and national electrotechnical regulations
must be observed
X11
X16
X13
X12
X11
L
N
X16
L1
31
32
X11
30
X16
N
31
32
30
X11
N
:
:
:
:
BK
BK
GN
GN
X13
T1
T2
T3
PE
PE
PE
X12=PE
PE
/ H1:N 7.1
/ X14:11 7.1
W2
Ölflex-110
10x0,5mm²
control cable
2
4
6
Q1
2
4
6
1
3
5
7
8
W2
Ölflex-110
10x0,5mm²
control cable
7
8
W1
LIYCY-JZ
4x1,5mm²
motor cable
Q1
.3
1
LT16
3
.2
5
KH16B
1
2
3
PE
SH=WH
The connection must be made by licenced personnel!
PE
PE
PE
X3
X0
L
N
PE
X0
X3
BN
BN
L
N
BU
X3
BU
X3
BN
BU
BN
BU
SW
SW
X3
U
W
PE
PE
PE
G1
G1
U
SW
CEE
V
CEE
SW
A1
L
N
PE
Y1
mains switch
mains switch
BK150FUE-HHS
BS150FUE-H
connecting lead:
3x2,5mm² fuse: 16A
slow-acting
optional
optional
M1
Y1
A2
mains supply
230V/50Hz
A1
V
brake
W
M
3~
PE
A2
operating current
brake (optional)
operator
2
4
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
mains supply
H28-283
=
+
Gesamt
Blatt
22
3
1
0
2
3
4
5
6
7
8
9
circuit board
24V
E201
F201
=NA=
3
SK2
watchdog
X26
4
90
E212
F212
/ X23:61 11.5
X24A
91
IN1
E101
70
71
IN2
E102
24V
X21A
40
IN3
E103
24V
41
40
24V
42
40
IN4
E104
IN8
E108
24V
43
X21B
44
24V
45
X22
55
IN10
E110
IN9
E109
24V
54
50
IN7
E107
24V
51
50
24V
52
57
56
1
S7
2
S35
X21A
X21B
X22
X24A
X26
: BK
: OR
: BK
: GN
: BK
WS32
Ölflex-110
2x0,75mm²
impulse up
WS33
Ölflex-110
2x0,75mm²
impulse down
3
S32
4
S33
4
3
4
S34
impulse down
impulse up
S36
no photocell 2 for
jumper
impulse operation
Name
intermediate stop
(optional)
optional
sluice on/off
interlock ON/OFF
option
Datum
Datum
USV
reserve
option
3
Änderung
WS36
Ölflex-110
2x0,75mm²
intermediate stop (optional)
3
external
emergency-OFF 2
emergency-OFF
WS34
Ölflex-110
2x0,75mm²
impulse operation
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
impulse generator
H28-283
5
=
+
Gesamt
Blatt
22
4
1
0
2
3
4
5
6
7
8
9
circuit board
+ - KS Cr Ak LS
5 4 1 6 2 3
X27
+24
E360
F361/F363/F364
GND1
IN6
E106
5 4 1 6 2 3
IN5
E105
Activation
+12
X22
55
X27
5
X24B
74
73
X27
4
X24B
72
X27
X22
1
58
X27
6
X24B
75
X27
X21C
2
48
X27
3
WX.3
6x
+ - KS Cr Ak LS
5 4 1 6 2 3
X.3
5 4 1 6 2 3
/ X3.2:3 6.0
/ X3.2:2 6.0
/ X3.2:1 6.0
X3.1
WA5.1
LIYY_757
5x0,5mm²
contact bar
A5.1
BN
BN
+24
WH
WH
9
10 11
YE
S
contact bar
RD
6
BK
7
E
4
GY
YE
GY
crash protection
Activation
S51.2
WA5.2
LIYY_757
4x0,14mm²
Diodes
A5.2
8
GN
GN
GND
7
WH
BN
YE
GN
5
1
9
8
11
2
3
10
BAT
WS51
Ölflex-110
2x0,5mm²
crash protection
BN
WS30.1
LIYY_757
3x0,14mm²
contact bar
receiver
WH
2
BN
WH
GN
S30.1
S51.1
S30.2
1
battery
crash protection
WS30.2
LIYY_757
3x0,14mm²
contact bar
transmitter
contact bar receiver
BN
WH
GN
NC
contact bar
transmitter
4
6
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
contact bar
H28-283
=
+
Gesamt
Blatt
22
5
1
0
X3.2
X3.2
X3.2
X3.2
X3.2
X3.2
:
:
:
:
:
:
1
2
3
4
5
6
24V
GND
-
2
3
BN
BU
WH
BN
BU
WH
X3.2
X3.2
X3.2
X3.2
4
:
:
:
:
1
2
3
4
-
5
#1
#2
#4
#3
6
7
8
X3.2 : 1 - BN
X3.2 : 2 - BU
X3.2 : 1 - BK
X3.2 : 2 - BU
X3.2 : 4 - BN + BK
X3.2 : 5 - BU
X3.2 : 6 - WH
X3.2 : 4 - BK + BN
X3.2 : 5 - BU
X3.2 : 6 - WH
9
IN5
E105
X21C
47
49
48
X3.2
1
2
3
X27
3
X.3:3 5.8 /
X3.1:8 5.8 /
X3.1:7 5.8 /
4
5
6
X3.2
1
3
4
X3.2
2
1
X3.2
2
4
4
5
X3.2
6
1
X3.2
2
ILG
4
4
5
6
BK
BN
BU
WH
ALG
option
W3
LIYY_757
4x0,14mm²
photocell
transmitter
EWS
transmitter
BN
BU
+
-
WH
W4
ASD_757
4x0,14mm²
photocell
receiver
BU
+
-
WH
EWE
NC
RES
5
WS4
BN
Ölflex-110
4x0,75
photocell
1
4
+
NO
-
Datum
COM
BN
+24
W(S41.2)
ASD_ILG
4x0,14mm²
photo grille receiver
BU
GND
BN
BU
TE
S41.2_ILG
WH
BN
+24
BN
BK
BU
COM GND
BK
BU
WH
W(S41.1)
ASD_757
2x0,14mm²
photo grille transmitter
NO
WH
S41.1_ALG
BK
BU
+24
GND
BK
BU
W(S41.2)
ASD_757
5x0,14mm²
photo grille receiver
S41.2_ALG
+24
COM GND
BK
BN
BU
NO
WH
NC
GY
photocell transmitter
photocell receiver
photocell
photo grille transmitter
photo curtain receiver
photo grille transmitter
photo curtain receiver
option
option
option
option
option
option
option
Datum
Änderung
2
S41.1_ILG
S4
Out
W(S41.1)
ASD_ILG
3x0,14mm²
photo grille transmitter
3
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
photocells
H28-283
7
=
+
Gesamt
Blatt
22
6
1
0
2
3
4
5
6
7
8
9
circuit board
P701
X14
P701
11
12
X14
10
11
P701
12
X14
10
11
P702
12
10
X15
21
22
20
X16:31 3.5 /
X11:N 3.5 /
WH1
Ölflex-110
3x0,75mm²
traffic light
H1
traffic light
WH2
Ölflex-110
2x0,75mm²
flashing beacon
N
R
R
H2
G
flashing beacon
N
G
G
traffic light
flashing beacon
option
option
door open signal
door closed signal
6
8
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
output module
H28-283
=
+
Gesamt
Blatt
22
7
1
0
2
3
4
5
6
7
8
9
circuit board
IN4
E104
24V
IN1
E101
24V
24V
GND
X21B
.WA8
COMFORT
8x0,34
44
46
44
45
GN
BN
PK
VT
X21A
BK
40
WH
X21B
41
GY
YE
WA8
COMFORT
8x0,34
GND COM NC
BN
PK
VT
NO
BK
COM NC
WH GY
COMFORT
NO
YE
44
46
44
GN
BN
PK
X21A
VT
BK
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
GND COM NC
BN
PK
VT
24V
40
WH
X21B
41
GY
YE
WA9
COMFORT
8x0,34
44
46
GN
BN
X21A
45
PK
VT
40
BK
WH
41
GY
YE
NO
BK
COM NC
WH GY
NO
YE
COMFORT
+24
GN
GND COM NC
BN
PK
VT
NO
BK
COM NC
WH GY
NO
YE
radar (optional)
2 x COMFORT
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
IN1
E101
A9
+24
GN
1 x COMFORT
Datum
Datum
24V
radar (optional)
7
IN4
E104
GND
A8
+24
GN
radar (optional)
Änderung
24V
GND
.A8
COMFORT
IN1
E101
Ers.f.
Ers.d.
9
radar (optional)
H28-283
=
+
Gesamt
Blatt
22
8
1
0
2
3
4
5
6
7
8
9
circuit board
A3
IN4
E104
24V
E501
E502
24V
GND
IN1
E101
24V
E401
GND
A6
radio receiver
A3
3
4
5
X21B
6
WA4
Ölflex-110
4x0,5mm²
photocell 2 (optional)
44
46
44
45
1
2
3
4
2
X21B
WA7
Ölflex-110
4x0mm²
radar
3
A4
L1
L2
46
44
1
2
3
X21A
-
NO
+
COM
41
4
A7
1
induction loops
(optional)
44
4
photocell 2 (optional)
radar (optional)
8
10
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
option
H28-283
=
+
Gesamt
Blatt
22
9
1
0
2
3
4
A1.1
5
6
7
8
9
TST-RFuX-COM
1
#1
2
3
4
.X4
1 2 3 4 5 6
5
.X3
1 2 3 4 5 6
1 2 3 4 5 6
1 2 3 4 5 6
6
7
8
9
10
automatic sluice operation
W6
6x
interlock
A2.1
TST-RFuX-COM
1
#2
2
3
4
.X4
1 2 3 4 5 6
5
.X3
1 2 3 4 5 6
6
1 2 3 4 5 6
1 2 3 4 5 6
7
8
9
10
9
11
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
option
H28-283
=
+
Gesamt
Blatt
22
10
1
0
2
3
4
5
6
7
8
9
circuit board
F752
A
X25
W2
X3
colours according to IEC757
BK
black
GY
grey
BN
brown
WH
white
RD
red
PK
2.1
B
E211
F211
+12
X24A:70 4.1 /
GND
X23
81
82
80
83
1
2
3
4
5
6
4
2
6
3
5
1
1.4
1.2
1.6
1.3
1.5
S10
OG
orange
GD
gold
YE
yellow
TQ
turquoise
GN
green
SR
silver
BU
blue
GNYE green-yellow
VT
purple
crank handle
60
X400
61
F1
F2
F3
F4
WSF
membrane keypad
SF
1.1
1
pink
E000/E050/E090
2.3
DES
2
2.2
2.4
2.5
1
2.6
2
F0
thermal
contact
violet
DES
external
emergency-OFF 1
membrane keypad
10
12
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
DES
H28-283
=
+
Gesamt
Blatt
22
11
1
2
3
4
5
6
7
8
9
SH
3
W
PE
PE
SH
PE
LIYCY-JZ
4x1,5mm²
2
V
U
PE
=
PE
=
=
=
operator
X3
=
1
U
PE
PE
3
PE
T3
T3
2
PE
T2
1
W1
Klemmennummer
T2
motor connection
T1
X13
T1
0
11
13
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
terminal connection diagramme
X13
H28-283
=
+
Gesamt
Blatt
22
12
1
2
4
5
6
7
8
9
NO
10
NC
12
COM
11
NC
12
NO
COM
11
10
NO
10
WH2
Ölflex-110
2x0,75mm²
NC
=
option
G
H2
option
R
H1
=
G
door open signal
G
=
option
traffic light
R
flashing beacon
WH1
11
Klemmennummer
12
door open signal
COM
X14
3
Ölflex-110
3x0,75mm²
0
12
14
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
terminal connection diagramme
X14
H28-283
=
+
Gesamt
Blatt
22
13
1
2
3
4
5
6
7
8
9
22
NO
20
=
door closed signal
21
Klemmennummer
NC
door closed signal
COM
X15
=
0
13
15
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
terminal connection diagramme
X15
H28-283
=
+
Gesamt
Blatt
22
14
1
0
2
3
4
5
6
7
8
9
4
41
41
4
WH
YE
YE
WH
Ölflex-110
4x0mm²
40
WA9
YE
WA7
YE
YE
COMFORT
8x0,34mm²
WH
WH
WH
COMFORT
8x0,34mm²
41
+24
+24
40
41
WA8
YE
4
COM
A9
-
+
-
NO
+
COM
NO
A7
=
WH
A8
=
WH
=
radar (optional)
WH
.A8
=
4
S34
impulse operation
=
impulse down
YE
YE
=
4
S33
=
WH
WH
WH
3
=
4
YE
=
3
S32
40
.WA8
3
WH
COMFORT
8x0,34mm²
43
+24
+24
4
3
impulse up
40
WS34
3
Ölflex-110
2x0,75mm²
40
4
42
+24
3
Ölflex-110
2x0,75mm²
WS33
Ölflex-110
2x0,75mm²
WS32
40
Klemmennummer
41
+24
X21A
14
16
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
terminal connection diagramme
X21A
H28-283
=
+
Gesamt
Blatt
22
15
1
2
4
5
6
7
8
9
+24
+24
GND
+24
44
45
44
46
44
2
3
4
1
2
3
WA7
2
3
2
3
4
4
4
1
+
2
3
NO
-
NO
+
COM
COM
=
A7
=
=
photocell 2 (optional)
=
=
=
=
A4
=
1
A9
=
GN
A8
=
GN
=
GN
.A8
3
=
2
radar (optional)
1
1
=
GN
GN
Ölflex-110
4x0mm²
GND
VT
VT
46
BN
BN
1
WA4
PK
PK
VT
+24
GND
46
BN
BN
BN
44
+24
44
GN
GN
GN
Ölflex-110
4x0,5mm²
+24
44
PK
45
GND
46
WA8
BN
COMFORT
8x0,34mm²
VT
VT
GN
WA9
PK
PK
+24
+24
44
BN
BN
44
GND
46
VT
=
radar (optional)
=
no photocell 2 for jumper
PK
COMFORT
8x0,34mm²
+24
44
GN
GN
BN
COMFORT
8x0,34mm²
.WA8
GN
45
+24
Klemmennummer
45
option
+24
X21B
3
44
0
15
17
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
terminal connection diagramme
X21B
H28-283
=
+
Gesamt
Blatt
22
16
1
2
BN
U
BU
SW
BN
BU
SW
SW
SW
V
U
W
V
PE
W
U
V
PE
PE
4
PE
1.4
=
BN BU
=
Anschluß
2
6
3
1.2
7
8
9
1.6
5
1.3
1
1.5
1.1
external emergency-OFF 1
DES
DES
=
=
=
=
M1
operator
=
6
1.4
PE
G1
5
W
M
3~
brake
4
limit switch box
dig. limit
switch
X3
3
=
0
16
18
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
connection diagramme X3
H28-283
=
+
Gesamt
Blatt
22
17
1
0
2
X3.1
8
9
10
11
WH
GN
YE
WH
GN
YE
4
5
6
7
8
9
contact bar
7
GY
BN
WA5.1
LIYY_757 5x0,5mm²
Anschluß
3
WH
GN
GY
YE
BN
GY
BN
Activation
crash protection
contact bar
A5.1
WH
17
19
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
connection diagramme X3.1
H28-283
=
+
Gesamt
Blatt
22
18
Änderung
Datum
Name
Norm
-
+
Bearb.
Lie
Gepr.
24.08.2009
-
WH
Out
1
+
Urspr.
2
-
Out
NC
+
3
COM
NO
COM
W(S41.1)
ASD_ILG 3x0,14mm²
photo curtain
transmitter
WS4
Ölflex-110 4x0,75mm²
photocell
4
4
NO
Datum
Ers.f.
BN
BU
+24
BN
BU
GND
+24
4
BN
4
Ers.d.
6
BU
BK
BN
BU
BK
+24
GND COM
1
WH
WH
NO
+24
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
+24
2
4
BK
BU
BK
BU
+24
BK
GND
BU
BN
BK
BU
BN
+24
GND COM
W(S41.2)
ASD_ILG 4x0,14mm²
photo curtain
receiver
5
W(S41.1)
ASD_ILG 3x0,14mm²
photo curtain
transmitter
4
W(S41.2)
ASD_ILG 4x0,14mm²
photo curtain
receiver
2
S41.2_ALG
BU
+
3
1
photo curtain receiver
RES
BN
3
S41.1_ALG
RES
2
3
photo grille transmitter
-
1
4
S41.2_ILG
WH
2
photo curtain receiver
+
WH
2
S41.1_ILG
BU
1
photo grille transmitter
BU
BN
6
=
+
5
=
1
=
BN
WH
S4
BU
4
photocell
BN
W4
ASD_757 4x0,14mm²
photocell
receiver
X3.2
=
3
=
2
EWE
W3
LIYY_757 4x0,14mm²
photocell
transmitter
1
=
EWS
Anschluß
=
transmitter
0
5
6
5
4
7
8
connection diagramme X3.2
H28-283
9
photocell
6
WH
WH
NO
+24
18
20
=
+
Gesamt
Blatt
22
19
1
0
2
3
4
5
6
7
8
cable overview
9
SEUS001D.F10 / LIE / 12.04.2007
Spannung
Page
V
W1
X3
X13
LIYCY-JZ
4
4
1,5
motor cable
W2
X3
W3
X3.2
X16;X11;X25;X23
Ölflex-110
10
EWS
LIYY_757
4
10
0,5
control cable
3
0,14
W4
X3.2
EWE
ASD_757
photocell transmitter
4
3
0,14
W6
A1.1-.X4
A2.1-.X4
photocell receiver
6
6
W(S41.1)
X3.2
S41.1_ILG;S41.1_ALG
ASD_ILG
3
4
0,14
photo grille transmitter
W(S41.2)
X3.2
WA4
X21B
S41.2_ILG;S41.2_ALG
ASD_ILG
4
8
0,14
photo grille receiver
A4
Ölflex-110
4
4
0,5
WA5.1
photocell 2 (optional)
X3.1
A5.1
LIYY_757
5
5
0,5
contact bar
WA5.2
A5.2
S51.2-S;S51.2-E
LIYY_757
4
4
0,14
Diodes
WA7
X21B;X21A
A7
Ölflex-110
4
4
0
WS30.1
A5.2
S30.1
LIYY_757
3
3
0,14
WS30.2
A5.2
S30.2
LIYY_757
3
3
0,14
contact bar transmitter
WS33
X21A
S33
Ölflex-110
2
2
0,75
impulse down
WS34
X21A
S34
Ölflex-110
2
2
0,75
impulse operation
WS36
X22
S36
Ölflex-110
2
2
0,75
intermediate stop (optional)
crash protection
WS51
A5.2
S51.1
Ölflex-110
2
2
0,5
WA8
X21B;X21A
A8
COMFORT
8
8
0,34
0,34
radar
contact bar receiver
WA9
X21B;X21A
A9
COMFORT
8
8
.WA8
X21B;X21A
.A8
COMFORT
8
8
0,34
WH1
H1
H2;X14
Ölflex-110
3
3
0,75
traffic light
WH2
X14
H2
Ölflex-110
2
1
0,75
flashing beacon
WS4
X3.2
S4
Ölflex-110
4
4
0,75
photocell
WS32
X21A
S32
Ölflex-110
2
2
0,75
WSF
X400
SF
WX.3
X.3
X27
4
6
impulse up
0
membrane keypad
6
19
21
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
cable overview
H28-283
=
+
Gesamt
Blatt
22
20
1
0
2
3
4
5
6
7
8
parts list
9
SEUO001D.F01 / LIE / 12.07.2007
NAME
WIRING DIAGRAMME LOCATION
MENGE
ME
1
DESIGNATION
MODEL NUMBER
MANUFACTURER
Schaltschrank BS 150 FUE H 400x300x150mm
ARTICLE NUMBER
Sarel GmbH
1
Schaltschrank BS 150 FUE H VA 400x300x150
Sarel GmbH
1
Steuerung BK 150 FUE H
TST-FUH CX-SE
013768
1
Steuerung BK 150 FUE H HS
1
Platine E FU H Erweiterungsplatine
1
Induktionsschleifendetektor 1-Kanal
TST SUVEK1
Feig Electronic GmbH
1
Induktionsschleifendetektor 2-Kanal
TST SUVEK2
Feig Electronic GmbH
1
Lichtschranke mit Reflektor
1
Gehäuse Kabellose Impulsübertragung
1
Platine Kabellose Impulsübertragung
3.1
A1
013768
013772
RFUx-COM
10.2
A3
800256
9.1
A3
800257
9.1
A4
Deutsche Telemecanique
800232
9.4
A5.1
OPT-CF 1163
10004300
5.0
A5.2
FRABA AG
FRABA AG
1
Batteriehalter 2XUM2 Softedge
Halter 2xUM2-DK
2
Batterie für kabellose Impulsübertragung
MN 1400, 9800mAH
1
Platine Funkempfänger 868,3MHz 1K
5.0
A5.2
5.0
A6
013551
FRABA AG
5.0
A5.2
FRABA AG
013550
Reichelt Elektronik
013561
Carl Scobel GmbH
013562
Deltron GmbH
011948
Deltron GmbH
9.8
A7
1
Radar-Bewegungsmelder
MWD BF1-A
1
Radar-Bewegungsmelder
MWD BP
1
Radar & Präsenzmelder COMFORT
COMFORT
1
Radar & Präsenzmelder COMFORT
COMFORT
1
Digitaler Endschalter
DES
1
Lichtschranke Einweg o. Kabel
EWS/EWE
Feig Electronic GmbH
800187
Feig Electronic GmbH
9.6
A7
Feig Electronic GmbH
800187.1
Feig Electronic GmbH
9.6
A8
014862
8.4
A9
014862
8.7
DES
Gesellschaft für Antriebstechnik
Gesellschaft für Antriebstechnik
11.4
EWS
Witt Sensorik
1
Bremsgleichrichter EGR2
EGR2
EGR2
1
Ampelgehäuse Rot/Grün Nr. 0671/s-2-E
3.4
H1
Gesellschaft für Antriebstechnik
Gesellschaft für Antriebstechnik
010681
010073
Witt Sensorik
6.0
G1
BK150FUEH-HS
014466
3.1
A1.1
BS150FUEH-V2A
014716
Sarel GmbH
A1
BS150FUEH
014715
Sarel GmbH
POS.
013341
800252
7.1
20
22
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
parts list
H28-283
=
+
Gesamt
Blatt
22
21
1
0
2
3
4
5
6
7
8
parts list
9
SEUO001D.F01 / LIE / 12.07.2007
NAME
WIRING DIAGRAMME LOCATION
H2
MENGE
ME
1
DESIGNATION
MODEL NUMBER
1
Blitzleuchte rot
1
Hauptschalter abschließbar BK150FUE H HS
1
Lasttrennschalter 16A
MANUFACTURER
Blitzleuchte orange
800255
7.2
Q1
S4
Kraus & Naimer
KH16B
3.3
1
Lichtschranke mit Reflektor
1
Not-Aus Taster
1
Not-Aus Schild
1
Opto Empfäng.kabell. Datenübertr. Antr.s.
1
Opto Sender kabell. Datenübertr. Lagers.
1
Lichtgitter ALG Bauhöhe 510mm
Kraus & Naimer
Deutsche Telemecanique
6.3
S7
XB7ES542P
Deutsche Telemecanique
Schneider Electric
4.0
S7
Deutsche Telemecanique
Schneider Electric
4.0
S30.1
FRABA AG
FRABA AG
5.4
S30.2
FRABA AG
FRABA AG
5.5
S41.1_ALG
Strack Lift Automation
Strack Lift Automation
6.7
S41.1_ALG
1
Lichtgitter ALG 70
683-ALG+70K5BR-K14
1
Lichtgitter ILG Bauhöhe 1590mm
685-ILG-24/06-L-K1-10
1
Lichtgitter ILG Bauhöhe 510mm
685-ILG-06/06-L-K1-10
Strack Lift Automation
Strack Lift Automation
6.7
S41.1_ILG
Strack Lift Automation
Strack Lift Automation
6.4
S41.1_ILG
Strack Lift Automation
Strack Lift Automation
6.4
S51.1
1
Feder m.Schalter 7000mm
Felsch Spritzguß GmbH
1
Federschalter m. Diode Antr.seite rechts
S51.2
1
Federschalter m. Diode Antr.seite links
5.2
S51.2
5.2
SF
1
Folientastatur 155,3x119,6mm mit Fenster
1
Drucktaster Auf-Halt-Zu für V2A-Schrank
SF
011167
800464
800465
013564
014142
Joetec
Kundisch GmbH
Tastaturverlängerung 250mm
Lück Elektrosysteme GmbH
Lück Elektrosysteme GmbH
11.8
1
800265
Felsch Spritzguß GmbH
Kundisch GmbH
X3.1
013724
78-004-007
Folientastatur klein 100x60mm
1
013725
013563
11.8
SF
011442
Felsch Spritzguß GmbH
Joetec
1
011440
78-004-006
11.8
SF
800232
011864
805349
11.8
BS150FUEH
370041.1
Felsch Spritzguß GmbH
5.1
BK150FUEH-HS
014351
WAH814/LT16/3VZM/Z20/X83/FR
3.2
Q1
POS.
800261
7.2
H2
ARTICLE NUMBER
Platine Getriebe
MAB Electronic
MAB Electronic
5.4
BS150FUEH-V2A
011874
BS150FUEH
370079
BS150FUEH-(V2A)
010566
014468
21
Datum
Änderung
Datum
Name
Bearb.
Lie
Gepr.
24.08.2009
Norm
Hörmann KG
Verkaufsgesellschaft
D-33803 Steinhagen
Urspr.
Ers.f.
Ers.d.
parts list
H28-283
=
+
Gesamt
Blatt
22
22
TST
Initial Operation
TST FUH
BK150FUEH
TST
Initial Operation
TST FUH
Notes
Important:
These instructions must be read before connecting the control and
before initial operation of the door system!
© Copyright 2008 by
Hörmann KG Verkaufsgesellschaft
D-33803 Steinhagen
http://www.hoermann.de/
With this edition, all previous editions become invalid.
The specifications in this document may be modified without notice.
The circulation and reproduction of this document, as well as the use and distribution of its contents, is not
permitted without our express permission. Compensation is required in case of infringement. All rights
reserved in case of patent grant or design registration.
This manual has been composed especially for those people fitting the door control TST FUH from Hörmann
KG Verkaufsgesellschaft. Initial operation of the control may only be carried out by electrical specialists with
accredited training familiar with the safety standards for electrical operator and automation systems.
The completeness of the initial operation manual is the sole responsibility of the person carrying out initial
operation of control TST FUH.
This manual shows only a small selection of control functions. For additional functions and descriptions of
individual door functions, more exact control specifications and warnings, see the additional information.
We have compiled the information in this document to the best of our knowledge. Hörmann KG
Verkaufsgesellschaft does not guarantee the accuracy and completeness of the specifications in this
document. A.Seuster GmbH & CO KG may especially not be held liable for consequential damages due to
defective or incorrect specifications. Despite our best efforts, errors can never be completely avoided. We
are happy to receive feedback at any time.
The installation recommendations in this document assume favourable general conditions. Hörmann KG
Verkaufsgesellschaft does not guarantee faultless operation in non-system environments.
Hörmann KG Verkaufsgesellschaft does not guarantee that the information contained in this document is
free of foreign industrial property rights. With this document, Hörmann KG Verkaufsgesellschaft does not
grant licences on its own or foreign patents or other property rights.
Warranty claims against Hörmann KG Verkaufsgesellschaft only apply to the immediate contractual partner
and are non-transferrable. Warranty will only be accepted for products that have been supplied by Hörmann
KG Verkaufsgesellschaft. We assume no liability for the total system.
The product descriptions, the products' use, options and performance data are not valid as warranted
characteristics and are subject to technical modifications.
General information on this document
In this functional description, the following symbols are used to alert the reader to various danger points and
helpful hints.
Indicates potential danger to
persons if the procedure is not carried out as
described.
Indicates danger to the control.
Hörmann KG Verkaufsgesellschaft
D-33803 Steinhagen
Hörmann KG Verkaufsgesellschaft
Page 1 of 30
HOE_FUH_GB.doc
Hörmann KG Verkaufsgesellschaft
IMPORTANT
Indicates information which is important for
door control or door function.
)
Indicates information which is useful, but not
absolutely necessary, for using door control TST
FUH.
Page 2 of 30
HOE_FUH_GB.doc
TST
Initial Operation
TST FUH
TST
Contents
1
Safety instructions
5
2
Technical data
6
3
Fitting the control
7
4
Electrical connection
8
4.1
Connecting the supply voltage...................................................................................................9
4.2
Motor connection .......................................................................................................................10
4.3
4.4.1
Absolute encoder..................................................................................................................12
4.4.2
Mechanical limit switches ....................................................................................................12
General operation information for parameterisation
Start the opening ..................................................................................................................21
9.8.3
Diagnostic display on the screen........................................................................................22
9.9
Error memory .............................................................................................................................22
9.10
Software version ........................................................................................................................23
9.11
Door operating time ...................................................................................................................23
9.12
Input voltage measurement ......................................................................................................23
9.13
Operating mode of the control .................................................................................................23
9.14
Password ....................................................................................................................................24
9.15
Memory time for opening commands ......................................................................................24
13
10
11
Parameter overview
24
Overview of messages
25
11.1
Internal system-induced errors F.9xx ......................................................................................28
11.2
Information messages ...............................................................................................................29
Modifying parameters................................................................................................................14
Initial operation...
14
6.1
... with absolute encoder ...........................................................................................................14
6.2
... with mechanical limit switches.............................................................................................14
6.3
Requesting new teach-in for limit stops..................................................................................15
7
9.8.2
Connecting the limit switch ......................................................................................................12
5.1
6
TST FUH
Connecting the safety strip.......................................................................................................11
4.4
5
Initial Operation
Further connection options
16
7.1
Photocell .....................................................................................................................................16
7.2
External command controllers .................................................................................................16
Overview of outputs
17
8
Overview of inputs
18
9
Functions
19
9.1
Software update .........................................................................................................................19
9.2
Door cycle counter.....................................................................................................................19
9.3
Maintenance counter .................................................................................................................19
9.4
Hold-open phase ........................................................................................................................19
9.5
Warning phase before door cycle/clearing time .....................................................................20
9.6
Limit stop correction .................................................................................................................20
9.7
CLOSE movement......................................................................................................................20
9.7.1
9.7.2
9.8
Correct travel limit door CLOSE..........................................................................................20
Start of the CLOSE movement.............................................................................................21
OPEN movement ........................................................................................................................21
9.8.1
Correct travel limit door OPEN ............................................................................................21
Hörmann KG Verkaufsgesellschaft
Page 3 of 30
HOE_FUH_GB.doc
Hörmann KG Verkaufsgesellschaft
Page 4 of 30
HOE_FUH_GB.doc
TST
1
Initial Operation
TST FUH
TST
Initial Operation
TST FUH
Safety instructions
2
Strictly observe the following important safety instructions, as well as the fitting and connection instructions,
during initial operation and operation of the control:
All installation, initial operation and maintenance work must be carried out exclusively by qualified personnel.
The following regulations must be observed with special care: VDE0100, EN 50110 (VDE0105), EN 60204
(VDE0113), EN 50178 (VDE0160), EN 60335 (VDE0700), fire prevention regulations, accident prevention
regulations, as well as the relevant applicable regulations for industrial doors (ZH1/494, EN12453, EN12978)
The control may only be opened if the supply is disconnected at all poles.
If the voltage-free contacts of the relay outputs or other contact points are externally fed, e.g. operated with a
dangerous voltage that may still be present after switching off the control or pulling the mains plug, a respective
warning label must be clearly visible on the control housing. ("Attention! Switch off all mains current circuits
before accessing the connecting terminals.")
Do not operate the control if it is open.
Operating the control with a dismantled CEE plug is only permitted if the mains supply can be disconnected
from the control at all poles via a suitable switch. The mains plug or the replacement switch used must be easily
accessible.
To avoid danger, the connecting cable of the unit, if damaged, must be replaced by the manufacturer, his aftersales service or a similarly qualified person.
Even after the supply has been switched off, dangerous voltages are present in the intermediate circuit
capacitors for up to five minutes. The discharge time for voltages under 60 V DC is at most 5 minutes. Touching
internal control parts during this discharge time is dangerous.
A defective power supply unit may considerably increase the discharge time of the intermediate circuit
capacitors to a voltage value under 60 V DC. Discharge times of up to 10 minutes may result.
If the 24 V control voltage is short-circuited or extremely overloaded, the power supply unit will not switch on
even though the intermediate circuit capacitors are charged. Display and LEDs remain dark. The power supply
unit can only be switched on after the short-circuit or extreme overload has been remedied.
The power supply unit is fed by the intermediate circuit capacitors for several seconds after the supply has been
switched off and continues its supply function for a period of time, depending on the power supply unit load. In
this case, the V 805 glow lamp lights up until the voltage has decreased.
Sections of the processor circuits are directy linked galvanically to the power supply. This must be considered
when carrying out any possible control measurements (when carrying out measurements in this area of the
process circuit, do not use measurement instruments with PE reference of the measuring circuit).
Do not operate the control without a connected protective earth conductor. If the protective earth conductor is
not connected, dangerously high voltages occur on the control housing, due to leakage capacities. The
protective earth conductor must be connected according to EN 50178, paragraph 5.2.11.1 for increased leakage
currents >3.5 mA.
If the control is covered in condensation, do not switch it on or operate it. This can destroy the control.
If controls are used outside the specified temperature range, a regulated, monitored heating system must be
provided to ensure that the specified operating temperature is maintained when switching on and operating the
control.
Do not operate a control with damaged keypad or vision panel. Damaged keypads and windows must be
replaced. To prevent damage to the keypad, do not operate it with sharp objects. The keypad is designed for
finger operation.
Before switching on the control supply for the first time, ensure that the evaluator cards (plug-in modules) are
plugged in the correct position. The control may be damaged if the cards are not plugged correctly or are
twisted, or if non-approved cards from other manufacturers are used.
When operating the door in dead-man mode, ensure that the door area is visible to the person operating the
door, as safety devices such as the safety strip and photocell do not activate in this mode.
Check the parameter settings and the function of the safety devices. Parameters, bridges and other command
units may only be set by instructed personnel.
Non-compliance with this safety information may endanger personal health and
safety, and may also damage the control.
These safety instructions do not claim to be complete. Please contact your supplier if you have any questions about the
product.
The manufacturer has carefully checked the unit hardware and software, as well as the product documentation, but can
not guarantee that it is free of errors.
The user must label the unit (type plate with name and address of manufacturer, serial number, type designation, supply
voltage and temperature range).
Hörmann KG Verkaufsgesellschaft
Page 5 of 30
HOE_FUH_GB.doc
Technical data
Dimensions of housing (W x H x D):
Fitting:
Supply voltage via L, N, PE:
Own consumption of control:
external supply 1 (230 V):
Control voltage/external supply 2:
Control voltage/External supply 3:
Control inputs:
Inputs INK 1 and INK 2:
RS485 A and B:
Safety chain/Emergency-off
Safety strip input:
Alarm signal
Relay outputs
USB
200 x 400 x 175 mm (without wall holder)
Via wall holder on floor of housing, standing vertically
230 VAC ±10%, 50...60 Hz
permissible range: 110...240 V ± 10%/50...60 Hz
Fuse: 16 A K Characteristics
max. 30 W when fully equipped
230 VAC ±10%, 50...60 Hz
(fused on the printed board: F202/1 AT)
24 VDC regulated (±5% at nominal voltage 230 V)
max. 500 mA to 40 °C, max. 250 mA to 50 °C
incl. optional plug-in modules
Fused via self-resetting semiconductor fuse, short-circuit proof via central circuit
regulator
For electronic limit switch and safety strip
Nominal value 11.5 V/max. 130 mA
24 VDC/type 15 mA, max. 26 VDC/20 mA
all inputs must be connected potential-free or:
< 5 V: inactive Æ logical 0
> 7 V: active Æ logical 1
Min. signal length for input control commands: > 100 ms
Galvanic separation via optoelectronic coupler on printed board
For two 24 V active impulse inputs offset by 90°, with max. load of 20 mA
< 5 V: inactive Æ logical 0
> 16 V active Æ logical 1
Only for electronic limit switches
RS485 Level, terminated by 100 Ω
All inputs must be connected voltage-free
Contact loading capacity: ≤ 26 VDC/ ≤ 120 mA
If the safety chain is interrupted, no operator movement is possible, not even in deadman mode
For electrical safety strips with 8.2 kΩ terminating resistor and for dynamic optical
systems
24 VDC/min. 10 mA/max.100 mA
Only Ohmic loads!
If inductive loads (e.g. additional relays or brakes) are connected, these must be
equipped with corresponding interference suppression (recovery diode, varistors, RC
modules).
For USB Memory Sticks (PC compatible)
HOST Plug connector: Type A
Max. power consumption: 100 mA
Max. cable length 2 m
Alternatively For PC communication with Feig protocol
Device Plug connector: Type B
Max. cable length 2 m
Communication module
Only suitable for TST RFUxCom
Relay K3: Changeover contact for releasing electromechanical brakes with upstream brake
Standard braking relay: rectifier
230 VAC/3 A
If EMERGENCY-OFF is activated, the brake relay will be released.
Relays K1 and K2: Volt-free change-over contact
Contacts used for power switching
"Malfunction/door position signals/traffic light min. 10 mA
can no longer switch small currents.
functions" max. 230 VAC/3 A
Operator output:
Brake resistance load (optional):
Temperature range (TST FUH- CXP)
Operation:
Storage:
Temperature range (TST FUH- CX)
Operation:
Storage:
Humidity
Vibration
Protection category
Weight
Hörmann KG Verkaufsgesellschaft
For operators up to 1.5 KW at 230 V
Motor constant current at 100% on-time and 40°C ambient temperature: 10 A
Motor constant current at 60% on-time and 50°C ambient temperature: 8 A
May be briefly overloaded up to 20 A for 0.5 s
Max. length of motor cable: 15 m
Max. 1.5 KW for max. 0.5 seconds.
Repeat rate min. every 20 seconds.
For printed boards, observe the own heat in the housing!
-20 … + 70 °C
-25 … + 70 °C
Installed in the housing
-20...+50 °C
-25...+70 °C
Up to 80% non-condensing
Low-vibration fitting, e.g. on a masonry wall
IP 54
Approx. 5 kg
Page 6 of 30
HOE_FUH_GB.doc
TST
Initial Operation
Directive
EMC Directive:
2004/1/08/EC
Low-voltage directive:
2006/9/5/EC
Type-tested according to:
Standards:
EN 61000-6-3:
EN 61000-6-2:
EN 61000-6-4:
EN 60335-1/02.2007:
EN12453/02.(2001):
EN12445/02.2001:
EN 61508:
Applied national technical specifications
regarding the directives above
EN12978/09.2003:
TST FUH
Emitted interference, residential environments
Interference resistance, industrial environments
Emitted interference, industrial environments
Safety of electrical equipment for domestic use and
similar purposes/Part 1
Doors and Gates – Safety in Use of Power-Driven
Doors - Requirements
Safety in use of power operated doors – Test
methods
Functional safety of
electrical/electronic/programmable electronic safetyrelated systems
Doors – Safety devices – Requirements and test
methods
TST
4
•
•
•
3
•
Fitting the control
•
Min .100 mm
The system must be switched voltage-free
while fitting the control.
50 °C
•
-20 °C
•
•
Before fitting, check the control for shipping
damage or other damage. In some cases,
damage inside the control may cause
considerable consequential damage to the
control and even endanger the health and safety
of the user.
Touching the electronic components, especially
those of the processor circuit, is prohibited.
Electronic components may be damaged or
destroyed by electrostatic discharge.
•
Before opening the housing cover, make sure
that no borings lying on the cover can fall into
the housing.
•
Ensure that the control is fitted free of torsion.
•
Unused cable entries must be closed by suitable
measures to maintain the housing's IP54
protection category.
1x 230 VAC,
N , PE
•
Min .100 mm
Initial Operation
TST FUH
Electrical connection
Connection, testing and maintenance of the
open control may only be carried out in a
voltage-free state. Closely observe the points
listed in the safety instructions section.
After the control is switched off, dangerous
voltage is still present for up to 5 minutes.
Due to residual voltages, touching the
electronic components is dangerous.
Never operate the control when the housing
cover is open.
•
•
The shield must be connected on both sides
(motor and control) and no additional
connections may be led in the cable.
Maximum cable length: 15 m.
Very high electrostatic charges may
accumulate, especially with high-speed plastic
curtain doors. When this charge discharges,
the control may be damaged. Therefore,
suitable countermeasures must be
implemented to prevent electrostatic charging.
Max. cross section for connections to printed
board terminals:
Single
wire
(rigid)
After completing the wiring and before
switching on the control for the first time,
check whether all motor connections on the
control side and on the motor side are
tightened and the motor is correctly connected
in star or triangle. Loose motor connection
usually cause damage to the converter.
All voltage inputs are galvanically separated
from the supply by a basic isolator. All
components attached to the control must have
at least one additional isolation with a rated
voltage of > 230 V (according to EN 60335-1).
For compliance with EMV directives, only
shielded, separate motor cables may be used.
Terminal screws
Plug-in terminals
Motor terminals
Mains voltage
2.5
1.5
2.5
2.5
Finely
stranded
(with/without
wire end
ferrule)
1.5
1.0
2.5
1.5
Figure 1: Fitting the control
• Do not subject the cable entry points to any
loads, particularly tensile loads.
Figure 2: Drilling diagram
Hörmann KG Verkaufsgesellschaft
Page 7 of 30
HOE_FUH_GB.doc
Hörmann KG Verkaufsgesellschaft
Page 8 of 30
HOE_FUH_GB.doc
TST
TST FUH
TST
Initial Operation
Motor connection
IMPORTANT
The mains plug must be
visible and accessible
from the control.
Figure 4: Motor connection
IMPORTANT
To ensure smooth operation of door control TST FUH, a shielded motor cable must be used. Also, do
not run any leads other than those of the motor connection in this cable.
Figure 3: Supply main connection
Hörmann KG Verkaufsgesellschaft
TST FUH
X301
4.2
K2
Connecting the supply voltage
K1
4.1
Initial Operation
Page 9 of 30
HOE_FUH_GB.doc
Hörmann KG Verkaufsgesellschaft
Page 10 of 30
HOE_FUH_GB.doc
TST
Initial Operation
TST FUH
TST
4.4
TST FUH
Connecting the limit switch
90 91 60
X26
X2
Connecting the safety strip
90 91 60
X26
X2
4.3
Initial Operation
X27
X27
Different types of limit switch systems may be used with door control TST FUH.
An absolute encoder is used as a limit switch in the standard setting. Furthermore, mechanical cam limit
switches can be used.
4.4.1 Absolute encoder
3
+12V
2
GND
70 71 72 73
3
70 71 72 73 74
"Electrical" strip
Coiled
cable
3
2
5
1
4
Coiled
cable
3
J 900: 1 - 2
J 900: 1 - 2
1
Door leaf
terminal
box
6
Dynamic optical
system
1
RS 485-B
4
Emerg.off chain
6
1
24V
Emerg.off chain
5
RS 485-A
Door leaf
terminal
box
Figure 7: Connecting the absolute encoder DES
72 73 74
72 73
70 71
70 71
Brown White
Figure 6: Absolute encoder DES
Safety strip
Optional
wicket
door
switch
J900
57 58 59
70 71
X24A
Terminating
resistor
8k2
X27
1,2K
8,2K
Cable
slack
switch
72 73 74 75
X24B
Jumper
J600 is
found on the Inside
top right (Brown)
corner of the
circuit board
Optional
wicket
door
switch
Cable
slack
switch
Receiver
4.4.2 Mechanical limit switches
Green
White
Brown
Outside
(white)
Sender
Figure 5: Safety strip connection
Different types of safety strips may be connected, e.g.:
•
•
Electrical safety strip with 8.2 kΩ terminating resistance.
Dynamic optical systems.
Figure 8: Cam limit switch
If one of these types of safety strips is connected when door control TST FUH is switched on, it will be
recognised automatically.
IMPORTANT If no safety strip is connected, no automatic access is possible.
Figure 9: Connecting the cam limit switch
Hörmann KG Verkaufsgesellschaft
Page 11 of 30
HOE_FUH_GB.doc
Hörmann KG Verkaufsgesellschaft
Page 12 of 30
HOE_FUH_GB.doc
TST
Initial Operation
TST FUH
TST
Initial Operation
TST FUH
)Alternatively, the pre-limit switches may also be connected as NC contacts.
5.1
5
General operation information for parameterisation
)Modification of the basic data is not necessary; this was set at the factory.
Opening parameterisation mode
1.
Disconnect
door control
Disconnect supply
at all poles
To modify parameters, proceed as follows:
-
The 7-segment display will turn off
after a delay of several seconds
(Observe safety information)
Service mode is activated,
close control box.
2.
SERVICE
Switch the
S400 switch to
(For position of S400 see Chapter
ON
5.1)
3.
4.
5.
Connect door
control
Å
¿
STOP
(permanent)
OPEN
(permanent)
Connect control
Activate STOP button and hold
-
If service mode is active, the first
decimal point will flash
Contents of display are dependent on
control status
Current messages will display, e.g.:
Wait approx. 2 seconds:
In parameterisation mode
Additionally activate OPEN
button and hold
. . . .
¿ OPEN
or
À CLOSE
The parameter value can be viewed
or modified (see below)
Display varies with selection
2.
3.
or
4.
or
5.
Å STOP (short)
¿ OPEN
À CLOSE
Å STOP (long)
STOP (short)
Å STOP (short)
Control is in parameterisation
mode
Name of desired parameter displays
Opening the parameter
The current parameter value is
displayed:
Use the OPEN button to
increase the parameter value
Use the CLOSE button to
decrease the parameter value
If the currently valid parameter value
is modified, the decimal points will
flash
Save set parameter value
The parameter is saved when all
points have stopped flashing
Discard set parameter value
Abort, the original parameter value is
displayed
Change to display the
parameter name
Display of parameter name
Å
Parameterisation mode is
exited immediately, door mode
is active again
Before initial operation of the control, check the electrical connection and the correct position of the
plug-in cards.
After initial start-up is complete, test the function of all safety devices. After initial operation is
complete, test the function of all safety devices.
P. 0 1 0
5
6
4
6
4
P. 0 1 0
6.1

....
Perform a reset of the control
Å+¿+À Press these simultaneously and hold approx. 3 seconds.
... with absolute encoder
1. Open CALIBRATION mode by briefly pressing the Å STOP button
2. Move door to door CLOSED position using À CLOSE on the membrane keypad and save by pressing
the Å STOP button for approx. 3 seconds.
Move door to door OPEN position using ¿ OPEN on the membrane keypad and save by pressing the Å
STOP button for approx. 3 seconds.

The last saved value is automatically
kept
Initial operation...
P. . . .
Exiting parameterisation mode
STOP (long)
Figure 10: Position S400
6
Parameter processing with selected parameter
1.
Pull the mains plug.
Switch the S400 DIP switch on.
Plug in the mains plug.
Simultaneously press the Å STOP and
the ¿ OPEN buttons for approx. 3 s to
enter the parameterisation mode of the
door control.
Modify the desired parameters.
After completing the settings, push the Å
STOP button for approx. 3 s to exit
parameterisation mode.
E. 2 0 1
P. 0 0 0
Selecting parameters in open parameterisation mode
Select desired parameter
A T T E N T I O N:
Not all parameters are directly
visible or modifiable, depending
on the password and the
positioning type setting
Modifying parameters
6.2
... with mechanical limit switches
1. Using the À CLOSE button, move the door to approx. 50 cm before closed position
IMPORTANT If the door does not move, the motor is lacking in power or, if necessary, check if
the brake is released.
IMPORTANT The distance is very dependent on the door type and speed, for fast doors, increase
the value.
With incorrect direction of door movement: incorrect motor rotating field, switch off the control
and swap the 2 motor connections.
2. Set the lower pre-limit switch so that it just triggers
IMPORTANT
After approx. 1h, the service mode will automatically set back. To re-enter service mode,
briefly switch off the control and then switch on again, or carry out a reset.
Hörmann KG Verkaufsgesellschaft
Page 13 of 30
HOE_FUH_GB.doc
Hörmann KG Verkaufsgesellschaft
Page 14 of 30
HOE_FUH_GB.doc
TST
Initial Operation
TST FUH
TST
Initial Operation
TST FUH
3. Using the À CLOSED button, move the door to approx. 10 cm before closed position
IMPORTANT The distance is very dependent on the door type and speed. For fast doors,
increase the value.
7
7.1
4. Set the lower limit switch so that it just triggers
Further connection options
Photocell
7.2
External command controllers
IMPORTANT Do not overshoot limit switch in end positions!
5. Using the ¿ OPEN button, move the door to approx. 50 cm before open position
IMPORTANT The distance depends greatly on door type and speed. For fast doors, increase the
value.
6. Set the upper pre-limit switch so that it just triggers.
7. Using the Ù OPEN button, move the door to approx. 10 cm before open position.
IMPORTANT The distance is very dependent on the door type and speed. For fast doors, increase
the value.
8. Set the upper limit switch so that it just triggers
IMPORTANT Do not overshoot limit switch in end positions!
9. If necessary for the door type: Set EMERGENCY limit switch at top and bottom
Connect the NC contacts, e.g. in the safety circuit, in series with the thermal switch.
10. Press the Å STOP and ¿ OPEN buttons to skip to parameterisation mode. Select parameter P.980
"Service mode", open it, and set the parameter value "2" to "0" (automatic mode)
11. If required, correct the door OPEN and door CLOSED limit switch positions by fine-tuning the end
positions in automatic mode.
Figure 11: Photocell connection
Figure 12: Connection for ext. command controllers
To prevent door from moving unintentionally, only adjust the limit switches if
EMERGENCY OFF is activated or control is switched off !
12. Now, door may be moved in automatic mode.
6.3
Requesting new teach-in for limit stops
If electronic limit switches are used and the limit stop teach-in was done in advance, but the limit stops are
not suited to the door, a new limit stop teach-in can be requested.
For this, the following parameters must be set:
P.210: 5 = New teach-in of all limit stops
Hörmann KG Verkaufsgesellschaft
Page 15 of 30
HOE_FUH_GB.doc
Hörmann KG Verkaufsgesellschaft
Page 16 of 30
HOE_FUH_GB.doc
TST
Initial Operation
TST FUH
TST
8
Initial Operation
TST FUH
Overview of inputs
K2
K1
Overview of outputs
F202 1A
X11
PE
X13
T1
U
230VAC
L,N,PE
PE
T2
T3 X14 10 11 12 X15 20 21 22 X16 30 31 32
V W
M
3~
Red traffic
light:
Flashes
during
door
cycle and
clearance
phase
Green
traffic
light:
Relay
active in
DOOR
OPEN
position
K3 NO
K3 Com
K3 NC
X12
K2 NO
K2 Com
K2 NC
N N
K1 NO
K1 Com
K1 NC
L L1 L1 N
Brake relay
The valid allocation of the inputs can be obtained in the switching documents!
Hörmann KG Verkaufsgesellschaft
Page 17 of 30
HOE_FUH_GB.doc
Hörmann KG Verkaufsgesellschaft
Page 18 of 30
HOE_FUH_GB.doc
TST
Initial Operation
TST FUH
TST
P.
9
Functions
9.1
P.
P.989
-w
9.2
P.
P.000
rr
9.3
P.
P.005
rr
P.015
ww
Software update
[Unit]
Function
Description/Notes
Adjustment
range
0 ... 1
Start software update The update of the control software is started via the
parameter. The update is started automatically when a USB
stick is inserted and the file name tst_fuh.bin is found. A
reset is carried out automatically after successful update.
You can also exit the Bootloader by performing a hardware
reset.
Function
Cycle counter
P.
P.025
-w
9.6
Door cycle counter
[Unit]
Adjustment
range
[cycles]
9.5
P.
Description/Notes
Shows door cycle counter
Illustration: 1234567 ⇒ 1234. À actuate .567
Illustration:
67 ⇒ 67
P.210
-w
Initial Operation
[Unit]
Adjustment
range
[sec.]
0 ... 200
Function
Minimum hold-open
phase
Function
Description/Notes
Deviating from the hold-open phase 1 or 2, the door is held
open for the minimum period of the set time. Then, the
closing is carried out automatically.
Warning phase before door cycle/clearing time
[Unit]
Function
Description/Notes
Adjustment
range
[sec.]
Warning phase before The door access is delayed by the time specified by this
0 ... 20
access
parameter after the input of a CLOSE command or after the
hold-open phase (forced closing) has elapsed.
0 = Warning phase deactivated
Limit stop correction
[Unit]
Adjustment
range
0 ... 5
Function
Description/Notes
New teach-in of the
limit stops
The teach-in for limit stops is restarted using this parameter.
The respective limit stops are moved to press-and-hold
operation after activating the sequence and saved by
keeping the stop button pressed.
The following setting possibilities are available:
Maintenance counter
[Unit]
Adjustment
range
[cycles]
0: Cancel, no limit stops have been taught in.
1: Teach-in of the limit switch down, limit switch up and,
when required, limit switch intermediate stop.
2: Teach-in of limit switch up and, when required, limit
switch intermediate stop are performed
3: Teach-in of limit switch down and limit switch up is
performed.
4: Teach-in of intermediate stop limit switch is performed.
5: Teach-in of all limit switches and the rotating direction
is performed.
Description/Notes
Maintenance counter The content of this parameter specifies the number of door
cycles still to be run until the maintenance is due.
) The setting -1 means that the maintenance counter has
not been activated yet.
P.973
-w
9.4
0 ... 1
Resetting the
maintenance counter
The maintenance counter is acknowledged by setting this
parameter to 1.
) Teach-in of the limit switch intermediate stop depends on
the setting in parameter P.244
Hold-open phase
) The hold-open phase that runs depends on the travel limit approached and the OPEN command used.
Each OPEN command can be set separately using the parameter P.5x4 as to if and which hold-open phase
elapses.
(X = Number of the input used).
P.
TST FUH
P.010
ww
[Unit]
Adjustment
range
[sec.]
0 ... 9999
P.011
ww
[sec.]
0 ... 9999
Function
Hold-open phase 1
Hold-open phase 2
Description/Notes
9.7
CLOSE movement
IMPORTANT
If the automatic adjustments of the pre-limit switches and limit switch bands are used (P.216 = 2), the
parameters P.222 and P.223 are modified automatically.
The parameters are also modified when the driving speed or the inclination of the ramp are changed,
as this leads to the restart of the automatic limit switch correction.
P.216 < 2 must be set if this ramp should be set manually.
The door is held in the travel limit door OPEN position for
the set time. Then, the closing is carried out automatically.
0 = Automatic closing deactivated
The door is held open in the travel limit intermediate
stop/partial opening for the set time. Then, the closing is
carried out automatically.
0 = Automatic closing deactivated
9.7.1 Correct travel limit door CLOSE
Hörmann KG Verkaufsgesellschaft
Page 19 of 30
HOE_FUH_GB.doc
Hörmann KG Verkaufsgesellschaft
Page 20 of 30
HOE_FUH_GB.doc
TST
P.
P.221
ww
Initial Operation
[Unit]
Adjustment
range
[Increment]
-125 ... 125
Function
TST FUH
TST
Initial Operation
Description/Notes
9.8.3 Diagnostic display on the screen
Correction value for
door CLOSED
With this parameter, the entire lower travel limit is moved
and therefore, the travel limit is moved together with the
corresponding pre-limit switch.
The adjustment of the parameter value in the positive
direction moves the travel limit upwards.
P.
P.910
-w
[Unit]
Adjustment
range
0 ... 22
Function
Display mode
selection
The adjustment of the parameter value in the negative
direction moves the travel limit downwards.
P.350
-w
9.8
[Unit]
Adjustment
range
[Hz]
6 ... 200
Function
Operating frequency
for fast CLOSE
movement
Description/Notes
Frequency specification for fast closing
(Operating frequency to lower pre-limit switch) → Adjust
pre-limit switch, if necessary
ATTENTION: Observe closing force at safety strip!
P.
P.231
ww
[Unit]
Adjustment
range
[Increment]
-60 ... 60
9.9
P.
P.920
rw
9.8.1 Correct travel limit door OPEN
Function
Description/Notes
Correction value for
door OPEN
With this parameter, the entire travel limit door OPEN is
moved and therefore, the travel limit is moved together with
the corresponding pre-limit switch.
The adjustment of the parameter value in the positive
direction moves the travel limit upwards.
The adjustment of the parameter value in the negative
direction moves the travel limit downwards.
P.310
-w
[Unit]
Adjustment
range
[Hz]
6 ... 200
Function
Operating frequency
for fast OPEN
movement
Hörmann KG Verkaufsgesellschaft
[Unit]
Adjustment
range
1 ... 10
Function
Description/Notes
Error memory
The control stores the last eight errors that have occurred in
the error memory.
After jumping to parameter P.920:
- Switch to the level using membrane key OPEN/CLOSE
- Open the error memory using the STOP button
- Close the error memory using the STOP button
- Exit the parameter P.920 using Eb Eb1: Error message 1 (most recent error)
Eb2: Error message 2
Eb3: Error message 3
Eb4: Error message 4
Eb5: Error message 5
Eb6: Error message 6
Eb7: Error message 7
Eb8: Error message 8
Ebcl: Delete the complete error memory
Eb-: Exit, jump back to P.920
Description/Notes
) The display Er- means that no error has been entered.
Frequency specification for fast opening
(Operating frequency to upper pre-limit switch) → Adjust
pre-limit switch, if necessary
Page 21 of 30
HOE_FUH_GB.doc
The control sequence is displayed (Automatic)
[Hz] Present driving speed
[A] Present motor current
[V] Present motor voltage
[A] Present intermediate current
[V] Present intermediate voltage
[°C] Present output stage temperature in °Celsius
[°F] Present output stage temperature in °Fahrenheit
[s] Present operating time of motor during last door
cycle
[Increment] Present position
[Increment] Position of the reference
[Dig] Value channel 1 of the absolute encoder
[Dig] Value channel 2 of the absolute encoder
[V] Present reference voltage
Error memory
9.8.2 Start the opening
P.
Using this parameter, the measurement variables at the
bottom can be viewed direct in the door control display.
The following variables are displayed:
9:
10:
11:
12:
13:
OPEN movement
IMPORTANT
If the automatic adjustments of the pre-limit switches and limit switch bands are used (P.216 = 2), the
parameters P.232 and P.233 are modified automatically.
The parameters are also modified when the driving speed or the inclination of the ramp are changed,
as this leads to the restart of the automatic limit switch correction.
P.216 < 2 must be set if this ramp should be set manually.
Description/Notes
0:
1:
2:
3
4:
5:
6:
7:
8:
9.7.2 Start of the CLOSE movement
P.
TST FUH
Hörmann KG Verkaufsgesellschaft
Page 22 of 30
HOE_FUH_GB.doc
TST
Initial Operation
TST FUH
9.10 Software version
P.
[Unit]
Adjustment
range
P.925
rr
TST
Initial Operation
9.14 Password
) The passwords can be set on level 2
Function
Description/Notes
Software version
The version of the current software used is displayed in this
parameter.
P.
P.999
-w
[Unit]
Adjustment
range
0 ... FFFF
Function
Password
9.11 Door operating time
P.
P.930
-r
[Unit]
Adjustment
range
[sec.]
TST FUH
Function
Operating time of the
motor
Description/Notes
The password enables the different parameter levels to be
accessed.
IMPORTANT
The different password levels allow access to different
numbers of parameters.
The parameters are not allowed to be modified without
knowing their function.
To avoid errors and risks resulting from unauthorised
access, passwords are only handed out to trained
personnel.
Description/Notes
The time required for the final movement is stored in this
parameter.
9.12 Input voltage measurement
P.
P.940
-r
[Unit]
Adjustment
range
[Volt]
Function
9.15 Memory time for opening commands
Description/Notes
P.
Input voltage
The value of the present input voltage applied is displayed
in this parameter.
P.017
-w
[Unit]
Adjustment
range
[sec.]
0 ... 60
Function
Memory time for
OPEN commands
P.980
-w
[Unit]
Adjustment
range
0 ... 5
Function
Operating mode
Description/Notes
The operating mode of the control is set in this parameter.
The following modes are possible:
) The adjustment of the fatigue testing is lost when the
control is switched off. Then the control is switched to
manual mode.
Page 23 of 30
10 Parameter overview
P.
0: OPEN and CLOSE movement in press-and-release
operation (Automatic)
1: OPEN movement in press-and-release operation,
CLOSE movement in manual mode (Semi-automatic)
2: OPEN and CLOSE movement in manual mode (Deadman mode)
3: Dead man-mode emergency run
4: Fatigue testing with safety devices automatic OPEN
and CLOSE movement. Before each new movement,
a new hold-open phase P.010. is performed.
5: Fatigue testing without safety devices
Hörmann KG Verkaufsgesellschaft
OPEN commands are saved for the time set here
) The adjustment 0 means that OPEN commands are not
saved.
9.13 Operating mode of the control
P.
Description/Notes
HOE_FUH_GB.doc
P.000
P.005
P.010
P.011
P.015
P.017
P.025
P.210
P.221
P.231
P.310
P.350
P.910
P.920
P.925
P.930
P.940
P.980
P.989
P.999
Function
Ex factory
Cycle counter
Maintenance counter
Hold-open phase 1
Hold-open phase 2
Minimum hold-open phase
Memory time for OPEN commands
Warning phase before access
New teach-in of the limit stops
Correction value for door CLOSED
Correction value for door OPEN
Operating frequency for fast OPEN movement
Operating frequency for fast CLOSE movement
Display mode selection
Error memory
Software version
Operating time of the motor
Input voltage
Operating mode
Start software update
Password
Hörmann KG Verkaufsgesellschaft
Page 24 of 30
ND [cycles]
ND [cycles]
5 [sec.]
10 [sec.]
3 [sec.]
60 [sec.]
0 [sec.]
5
0 [Increment]
0 [Increment]
65 [Hz]
30 [Hz]
0
0
ND
ND [sec.]
ND [Volt]
0
0
0
Modified
by:
on:
PAGE
19
19
19
19
20
24
20
20
21
21
21
21
22
22
23
23
23
23
19
24
HOE_FUH_GB.doc
TST
Initial Operation
TST FUH
TST
If errors do not reset themselves, they may be acknowledged.
Before the corresponding message is acknowledged, the cause of the error must be
eliminated.
To do this, press the Å STOP button and hold it down, then press the EMERGENCY-OFF button.
Alternatively, you can also press the Å STOP button for approx. 5 seconds.
Door position outside top
•
Door position outside bottom
•
•
•
•
•
F.201
Internal emergency-off
"mushroom button" activated
•
•
F.211
or watchdog (processor
monitoring)
External emergency-off 1
activated
External emergency-off 2
activated
F.212
Incorrect travel limits
F.005
Parameter value for top emergency limit switch is too
small
Upper limit switch range (limit switch band) is too small
Mechanical brake is defective or incorrectly set
Parameter value for bottom emergency limit switch is too
small
Lower limit switch range (limit switch band) is too small
Mechanical brake is defective or incorrectly set
•
Operating time exceeded
(during opening, closing or
dead-man)
•
F.021
Testing of the emergency
opening failed
F.030
Contouring error (change in
position of door is less than
expected)
F.031
Detected direction of rotation
differs from the expected
direction of rotation
•
•
•
•
•
•
•
•
•
•
•
F.043
Malfunction of photocell's prelimit switch
•
Current motor operation time has exceeded set
maximum operation time; door may be sluggish or
blocked.
If mechanical limit switches are used, one of the limit
switches did not engage
The max. permissible runtime during the testing period
has been exceeded.
Call service department
Door or motor is blocked
Power too low for starting torque
Speed insufficient
Mechanical limit switch was not passed or is defective
Fixing to shaft of absolute encoder is not tightened
Wrong positioning system selected (P.205)
When using increment encoders: Channel A and B have
been swapped
Motor's direction of rotation was switched compared to
calibration
Too much "sagging" when door starts to move, brake
releases too soon, or torque is too low, boost may need
to be adjusted.
The photocell's pre-limit switch remains engaged also at
centre travel limit or upper travel limit.
F.060
The control cabinet has just
been switched on or the rubber
bottom part has been hit
Short circuit detected at strip
input
Set limit for number of strip
activations during closing has
been reached
Redundancy error at short
circuit
•
Line short detected in strips with NC contacts
•
Parameterised, maximum number of safety strip
triggerings during a door cycle has been exceeded
•
F.366
Impulse frequency too high for
optical safety strip
•
•
F.369
Internal safety strip
parameterised incorrectly
Malfunction of safety strip's
pre-limit switch
•
An internal safety strip is connected but deactivated.
•
Number of activations
exceeded, safety A
Number of activations
exceeded, safety B
Number of activations
exceeded, safety C
•
Pre-limit switch for safety switch deactivation, and/or
reversal after safety switch activation, remains engaged
also at upper travel limit.
Parameterised maximum number of activations of
safety A during one door cycle has been exceeded
Parameterised maximum number of activations of
safety B during one door cycle has been exceeded
Parameterised maximum number of activations of
safety C during one door cycle has been exceeded
•
F.363
Interruption at strip input
F.364
Safety strip – Testing failed.
•
•
•
•
•
F.365
Redundancy error at
interruption
•
•
F.385
F.3B1
Reset procedure, see:
•
Fitting instructions
•
Wiring diagram
•
Control cabinet door outside
•
One of the evaluator channels for short circuit
recognition does not respond identically to the second
channel. Æ Control unit print defective
Dynamic optical system connected but not set in
parameter P.460.
Connecting cable defective or not connected.
Terminating resistor defective or missing.
Jumper set incorrectly.
Testing request did not activate safety strip as
expected.
The time period between testing request and testing is
not adjusted.
One of the evaluator channels for interruption
recognition does not respond identically to the second
channel.
Æ Control unit print defective
Dynamic optical system connected but not set in
parameter P.460.
Defective optical safety strip
Defective input for internal safety strip.
F.362
F.3A1
Operator call crash system
•
Emergency stop chain was interrupted at the "internal
emergency-off“ input, but parameterisation mode was
not selected
Internal parameter or EEPROM tests failed. Activate the
STOP membrane key for more information on the cause
Emergency stop chain interrupted at emergency-off input
1
Emergency stop chain interrupted at emergency-off input
2
Malfunction of the safety contact strip
F.360
F.361
Implausible door operation
F.020
TST FUH
Safety chain malfunctions
11 Overview of messages
F.000
Initial Operation
F.3C1
•
•
Maintenance counter is exceeded
F.080
Malfunction: Maintenance is
required
•
Service counter has run down
Parameter is not set
F.090
Control is not parameterised
Hörmann KG Verkaufsgesellschaft
•
The basic parameters (P.205, P.100 to P.103) of control
TST FUS have not been set.
Page 25 of 30
HOE_FUH_GB.doc
Hörmann KG Verkaufsgesellschaft
Page 26 of 30
HOE_FUH_GB.doc
TST
Initial Operation
TST FUH
TST
Initial Operation
TST FUH
General hardware error
General hardware error
malfunction
Watchdog error
•
•
•
•
Severe malfunctions in the supply voltage
Internal watchdog has activated
RAM error
Internal watchdog has activated
Software exception
•
Internal error recognized
Overload current
(Motor current or intermediate
circuit)
•
F.400
Hardware reset of control
recognised
F.401
F.40A
F.410
F.420
Overload in intermediate
circuit
Limit 1
•
•
•
•
•
F.425
F.426
F.430
Mains overvoltage
•
Incorrect nominal specifications set for motor (P100 –
P103)
Voltage increase/boost set not adjusted (P140 or
P145)
Motor incorrectly dimensioned for door used
Door is sluggish
Brake chopper malfunctioning/defective/not present
Supply voltage much too high
The motor feeds too much energy back during
generation operation, the kinetic energy of the door
can not be sufficiently reduced.
The supply voltage of the control is too high
Mains undervoltage
•
The supply voltage of the control is too low
Heat sink temperature is
outside operating range
Limit 1
•
•
•
F.435
Malfunction: Temperature in
housing rising above 75 °C
•
•
Load on output stage or brake chopper too high
Ambient temperature too low for control operation.
Output stage clock frequency too high (parameter
P.160)
Load on frequency converter/switching too high
Control box not sufficiently cooled
F.440
Overload current in
intermediate circuit
Limit 1
Overload current in
motor/intermediate circuit
Limit 2
•
•
•
•
F.510
F.515
Motor protection function has
recognised overload current
•
•
•
•
•
•
•
F.519
IGBT driver module has
recognised overload current.
•
•
•
F.520
F.521
Overload in intermediate
circuit
Limit 2
•
•
•
•
•
•
Undervoltage in intermediate
circuit
•
•
Hörmann KG Verkaufsgesellschaft
Set voltage increase ("boost") not adjusted
Motor incorrectly dimensioned for door used
Door is sluggish
Incorrect nominal specifications set for motor (P100 –
P103)
Voltage increase/boost set not adjusted (P140 or
P145)
Motor incorrectly dimensioned for door
Door is sluggish
Incorrect motor characteristic curve (motor nominal
current) set (P101)
Voltage increase/boost set too high (P140 or P145)
Motor incorrectly dimensioned
Short circuit or earth contact at motor terminals
Motor nominal frequency set extremely incorrectly
(P100)
Voltage increase/boost extremely excessive (P140 or
P145)
Motor incorrectly dimensioned
Motor winding defective
Brief interruption of emergency-off circuit.
Brake chopper malfunctioning/defective/not present
Input supply voltage too high
The motor feeds too much energy back during
generation operation, as it needs to reduce the kinetic
energy of the door.
Input supply voltage too low, usually with load
Load too high/output stage or brake chopper
Page 27 of 30
HOE_FUH_GB.doc
F.524
External 24 V supply missing
or too low
•
•
F.525
Overvoltage at the power
input
Heat sink temperature
Operating range
Limit 2
Malfunction: Temperature in
housing rising above the
critical 80 °C
Overload current in
intermediate circuit
Limit 2
•
•
•
•
•
•
Overload, but no short circuit.
If the 24 V short circuits, the control supply does not
switch on and the V 306 glow lamp lights up.
The supply voltage is too high
The supply voltage has a high fluctuation
Load on output stage or brake chopper too high
Clock frequency of output stage too high (P160)
Ambient temperature of control too low
Internal temperature too high
•
•
•
Set voltage increase ("boost") not adjusted
Motor incorrectly dimensioned for door used
Door is sluggish
F.530
F.535
F.540
Error in positioning system
F.700
F.752
F.760
F.762
Position detection defective
For mechanical limit switches:
• At least one limit switch does not correspond to
parameterised active status.
• An implausible combination of at least 2 active limit
switches.
For electronic limit switches:
• After factory parameter activation was called up
(parameter P.990), the corresponding positioning
system was not parameterised.
• Calibration is incomplete or defective and must be
repeated.
• The intermediate travel limit, when activated, is
implausible.
• Synchronisation not completed or reference switch
defective
Timeout during log transfer
• Interface line defective/interrupted
• Evaluation electronics of absolute encoder are
defective
• Defective hardware or severely malfunctioning
environment
• Shield connection cable
• Fit RC module (100 Ω + 100 nF) to brake
Position is outside range area
• Position sensor operator defective
• Evaluation electronics of absolute encoder are
defective
• Defective hardware or severely malfunctioning
environment
Electronic limit switch
• Upper limit switch Eo or intermediate limit switch E1
positions are incorrect
has exceeded the valid limit range
• Control has not been initialised
• Position specifications incorrect during calibration, or
values no longer plausible
11.1 Internal system-induced errors F.9xx
These errors are internal errors which cannot be eliminated by the person operating the control.
If this type of error occurs, please contact customer service immediately.
Hörmann KG Verkaufsgesellschaft
Page 28 of 30
HOE_FUH_GB.doc
TST
Initial Operation
TST FUH
TST
Initial Operation
I.903
I.904
I.905
I.906
Malfunction of the safety strip (closer) during the last closing, the message is deleted
after the close position has been reached without malfunctions
Upper limit switch is being corrected
Upper pre-limit switch is correct
Upper limit switch band is correct
Lower limit switch is being corrected
Lower pre-limit switch correct
Lower limit switch band correct
Limit switch correction complete
Control is preparing automatic teach-in of limit switches
Max. speed during the automatic limit switch correction has not been reached.
Limit switch correction is being carried out
Waiting for USB stick
The update file could not be found on the stick (the file with the name tst_fuh.bin should
be in the root directory)
File cannot be opened
ROM will be deleted
ROM is being programmed
Update file has an incorrect format (not implemented yet)
noEr
Er-Prog
Error memory: no error stored
Error memory: error is found without a corresponding message
Programming message during execution of original parameters or default set.
I.365
11.2 Information messages
STOP
_Eu_
≡Eu≡
ZUF@
-Eo≡Eo≡
@OPEN
-E1≡E1≡
FAIL
EICH
≡NA≡
NOTF
'Hd'
ParA
SYNC
'Au'
'Hc'
FUS
E.i.E.u.
E.i.E.o.
E.i.E.1.
Hd.cL
Hd.oP
Hd.Eu
Hd.Eo
Hd.Ao
I.023
I.080
I.100
I.150
I.160
I.161
I.170
I.180
I.185
I.199
I.200
I.201
I.202
I.203
I.205
I.210
I.211
I.310
I.360
General messages
Stop/reset status, waiting for the next entered command
Lower limit switch Eu
Lower travel limit locked → No opening possible (e.g. air lock)
Active closing
Upper travel limit Eo
Upper travel limit locked → No closing possible (e.g. safety loop)
Active opening
Centre travel limit E1 (intermediate travel limit)
Centre travel limit locked → no closing possible (e.g. safety loop)
Malfunction → Only dead-man operation possible, and possibly automatic opening
Calibration → Setting the travel limits in dead-man operation
(With absolute encoder) → Begin process via STOP button
Emergency-off → No door operation possible, hardware safety chain interrupted
Emergency operation → Dead-man operation, ignores all safety devices, etc.
Manual → Dead-man operation
Parameterisation
Synchronisation (Incremental position sensor/limit switch → unknown position)
Automatic → Designates change of status from "Manual" to "Automatic"
Semi-automatic → Marks the change from"Manual mode" to "Automatic mode"
First display after switching on (power up and self-test)
Status messages during calibration
Request for calibration of lower travel limit (in dead-man operation)
Request for calibration of upper travel limit (in dead-man operation)
Calibration of intermediate travel limit E1 (in dead-man operation)
Status messages during dead-man operation:
Dead-man closing (membrane key: CLOSE)
Dead-man opening (membrane key: OPEN)
Lower travel limit has been reached, no further dead-man closing possible
Upper travel limit has been reached, no further dead-man opening possible
Outside the permitted Eo position (no dead-man opening possible)
Information message during automated operation:
Emergency opening message released
Maintenance will be necessary soon/service counter will run down soon
Speed too high when upper travel limit is reached
Speed too high when lower travel limit is reached
Permanent OPEN still active
Open command encoder priority active, close movement only with a command encoder
that has the same priority (see p.5 x 4)
Safety opening is being carried out
Wait for the command of the membrane keypad
Waiting for acknowledgement (service request), display flashing
Door cycle counter implausible (re-initialise → parameter)
Reference position corrected or recognised (after calibration)
Reference position re-initialised
Reference position missing
Reference position incorrect
Synchronisation
Upper pre-limit switch implausible
Lower pre-limit switch implausible
OPEN command is transmitted to door 2
Malfunction of the safety strip (opener) during the last closing, the message is deleted
after the close position has been reached without malfunctions
Hörmann KG Verkaufsgesellschaft
Page 29 of 30
HOE_FUH_GB.doc
TST FUH
I.500
I.501
I.502
I.505
I.506
I.507
I.510
I.515
I.520
I.555
I.901
I.902
Information messages during the parameterisation:
General inputs
E.000
E.050
E.090
E.101
E.102
E.103
E.104
E.105
E.106
E.107
E.108
E.109
E.110
E.121
E.128
OPEN button on membrane keypad
STOP button on membrane keypad
CLOSE button on membrane keypad
Input 1 : see wiring diagram
Input 2 : see wiring diagram
Input 3 : see wiring diagram
Input 4 : see wiring diagram
Input 5 : see wiring diagram
Input 6 : see wiring diagram
Input 7 : see wiring diagram
Input 8 : see wiring diagram
Input 9 : see wiring diagram
Input 10 : see wiring diagram
Input 21 : Reserve
Input 28 : Reserve
E.201
E.211
E.212
Internal emergency-off "mushroom button" activated
External emergency-off 1 activated
External emergency-off 2 activated
E.360
Activation of internal safety strip
E.401
E.402
Radio control channel 1
Radio control channel 2
Safety/emergency stop chain
General safety strip
Radio control plug-in module
E.501
E.502
E.900
Induction loop evaluator plug-in module
Detector channel 1
Detector channel 2
Internal inputs
Fault signal from drive module
Hörmann KG Verkaufsgesellschaft
Page 30 of 30
HOE_FUH_GB.doc
Hörmann KG Verkaufsgesellschaft
D-33803 Steinhagen
2 Possibilities of adjustment
4 Outputs and LED-display
2.1
4.1
Sensitivity
By adjusting the sensitivity, you determine a change of inductivity for
each channel, which a vehicle has to cause in order to set the
appropriate output of the detector.
Sensitivity adjustment is done separately for each channel with the
help of 2 DIP-switches.
Sensitivity level
Operating instructions
induction loop detector
plug-in card for control panels
TST SUVEK1 - 1-channel detector
TST SUVEK2 - 2-channel detector
2.2
Service
5
CH 2
green
LED
red
1
3
ON
1
8
OFF/OFF
2
(0,09% ∆f/f)
ON
1
8
ON/OFF
3
(0,03% ∆f/f)
ON
1
8
OFF/ON
4 high
(0,01% ∆f/f)
ON
1
8
ON/ON
X2
ON
1
8
OFF
infinite
ON
1
8
ON
2
1
2.3
X5
3
4
3
low
Loop occupied / loop fault
4.3
Frequency adjustment and rebalancing
Channel 1: DIP-switch 4
Channel 2: DIP-switch 8 *)
low
ON
1
high
ON
1
8
LED-display
Red LED
Loop
condition
2
off
off
No supply voltage
off
Alignment or frequency indication
on
off
Detector ready, loop free
on
on
Detector ready, signal indication
off
on
Loop fault
Indication of loop frequency
Approx. 1 s after the detector has been aligned, the loop frequency is
indicated via flash signals of the green LED. First, the 10kHz-digit is
indicated. In steps of a loop frequency of 10kHz, the green LED of
the detector channel will flash one time. After a break of 1s , the
1kHz-digit is indicated in the same way. If the units digit has the
significance of '0', 10 flash signals will be emitted. The 1kHz-flash
signals will be a little shorter than those of the 10kHz-digit.
Example of a loop frequency of 57 kHz:
tens
OFF
1 General
Characteristic features:
The induction loop detector TST SUVEK1/2 is a system for inductive
detection of vehicles with the following characteristic features:
• evaluation of 1 (TST SUVEK1) or 2 (TST SUVEK2) loops
• galvanic separation between loop and detector electronics
• automatic system alignment immediately after activation
• continuous resetting of frequency drifts
• no mutual influence of loops 1 and 2 by multiplex processes on
TST SUVEK2
• sensitivity is independent of loop inductivity
• occupied-message on LED-display
• open-collector outputs, galvanically separated by optocouplers
• additional, looped-through I/O, galvanically separated by
optocouplers
• indication of loop frequency via LED
• diagnosis possibility in connection with diagnostic unit VEK FG2
8
ON
5x 10kHz
The admissible frequency range is 30kHz to 130kHz. The frequency
depends on the loop geometry, number of turns, inductivity resulting
from the loop supply line and the chosen frequency level.
A rebalancing can be manually triggered by changing the frequency
adjustment of a channel.
As soon as switched on, the detector automatically carries out an
adjustment of the loop frequency. In case of a short-term voltage loss
of <0,1s no rebalancing will take place.
3 Connections
Connection
X1 / 1
X1 / 2
X1 / 3
X1 / 4
X1 / 5
X2 / 1
X2 / 2
X2 / 3
X2 / 4 - X2 / 5
X5 / 1 - X5 / 2
X5 / 3 - X5 / 4
• The appliance may only be used for the purpose intended by the
manufacturer.
• Please hand out the operating instructions to all users and keep i
in an easily accessible place.
• Unacceptable changes as well as the use of spare parts and
special features which are not sold or recommended by the
manufacturer of the appliance, may cause fire, electric shocks and
injuries. Therefore, such measures lead to nonliability of the
manufacturer and a lapse of all warranty claims.
• The appliance is subject to the manufacturer’s guarantee
regulations in the version valid at the time of purchase. We canno
be held liable for improper or faulty manual or automatic adjustmen
of parameters resp. improper use of the appliance.
• Repair work may only be carried out by the manufacturer.
• Installation, initiation, maintenance, measuring and adjustment o
the traffic detector should only be carried out by electricians with a
good knowledge of the rules for prevention of accidents.
• When handling appliances that come into contact with electricity
the valid VDE-regulations have to be observed. In particular, these
are (list may be incomplete): VDE 0100, VDE 0550/0551, VDE
0700, VDE 0711, VDE 0860, VDE 0105 as well as the rules for the
prevention of accidents and fire, VBG4.
• All labour that is carried out on the appliance as well as its
initiation, has to conform to the national as well as the local electric
regulations.
• The user has to make sure that the appliance is installed and
operated according to the technical rules of the country o
installation as well as other regional regulations. Cable dimensions
protection, grounding, disconnection, insulation control and excess
current protection should be especially considered.
• According to machine directive 89/392/EWG, appendix IV, as wel
as directive ZH1/494 of the German employer’s liability insurance
association, the appliance must not be used as a safety
component. Systems with a high danger potential need additiona
safety contrivances!
units
1s
1
Please read the operating- and safety
instructions thoroughly before putting the traffic
detector into operation !
Detector condition
flashes
X1
4
Type
Supply
GND
Supply
24V DC
Optocoupler
GND
Optocoupler-outp. Channel 2 *)
Optocoupler-outp. Channel 1
add. optocoupler
output
add. optocoupler
input
outp. 24V DC (connect. X1 / 2)
--Loop channel 1
Loop channel 2 *)
*) nur TST SUVEK2
Notice: GND-pin X1 / 1 has to be connected externally with PE !
HOE_SUVEK02.doc
Loop free / Reset / rebalancing
Green LED
Loop
control
The actual frequency of the detector can be adjusted in two levels
with the help of DIP- switches 4 and 8.
Frequency
Detector conditions
high
The green LED indicates that the detector is operable. The red LED
indicates activation of the relay output in dependence on the seizure
condition of the loop.
Channel 1: DIP-switch 3
Channel 2: DIP-switch 7 *)
5 minutes
5
2
4.2
Holding time
Holding time
8
1
Loops
ON
1
4
72.5 mm
Sensitivity b
Sensitivity a
Holdingtime
Frequency
Sensitivity b
Sensitivity a
Holdingtime
Frequency
(0,27% ∆f/f)
2
CH 1
Optocoupler-outp. 1/2
The holding time can be adjusted with the help of DIP-switches 3 and
7. After the holding time has expired, a "loop free" signal is emitted,
followed by an automatic rebalancing of the loops. The holding time
starts as soon as the loop is seized.
50.0 mm
green
LED
red
Signal indication is done via optocoupler-outputs pin 4 and 5 at plug
X1. GND-reference is X1 pin 3.
Channel 1: DIP-switch 1, 2
Channel 2: DIP-switch 5, 6 *)
1 low
6 Safety instructions
Outputs
15.12.04
7x 1kHz
5 Technical data
Dimensions
Protection class
72,5 x 50 x 18 mm (LxWxH without plug)
IP 00
Current supply
24V DC ±20% max. 2,0W
Working temperature
Storage temperature
Air moisture
-20 °C to +70 °C
-20 °C to +70 °C
max. 95 % non-thawing
Loop inductivity
Frequency range
Sensitivity
Holding time
20-800 µH, recommended 75-400uH
30-130 kHz in 2 levels
0,01 % to 0,27 % (∆f/f) in 4 levels
0,02 % to 0,54 % (∆L/L)
5 min. or infinite
Loop lead in
Loop resistance
max. 100 m
max. 20 Ohm (incl. supply line)
Optocoupler output
45V / 10mA / 100mW
Slow operation
Signal duration
Fall-delay time
50ms TST SUVEK1, 100ms TST SUVEK2
> 200 ms
25ms TST SUVEK1, 50ms TST SUVEK2
Connection
2x MOLEX-socket, series 3215, 5-pole
1x plug-in terminal, 4-pole, RM 3,81
CE- standards
EN 61000-6-2, March 2000
EN 50081-1, March 1993
Notice
The indications made in these operating instructions may be altere
without previous notice.
With the edition of these instructions, all previous editions becom
void.
Composition of the information given in this manual has been done t
the best of our knowledge. Hörmann KG Verkaufsgesellschaftdoe
not guarantee the correctness of the details given in thes
instructions and may not be held liable for damages ensuing from
incorrect installation.
Since, despite all our efforts, errors may not be completely avoided
we are always grateful for your useful tips.
The installation instructions given in this manual are based o
advantageous
boundary
conditions.
Hörmann
KG
Verkaufsgesellschaftdoes not give any guarantee promise for perfec
function of the traffic detector in cross surroundings.
 Copyright 2004 by Hörmann KG Verkaufsgesellschaft
Technische Mitteilung TM-EL19
Technical Bulletin TM-EL19
von
: Michael Lienenkämper
Author
: Michael Lienenkämper
Datum
: 17.11.06
Date
: 17.11.06
Verteiler
: Gruppe A, B, C, D, E, F
Distribution
: Gruppe A, B, C, D, E, F
über
: Handsender HS-SEU
about
: Hand Transmitter HS-SEU
hier
: Programmieranleitung
.-.-.-.-.-.-.-.-.-.-
here
: Programming Manual
.-.-.-.-.-.-.-.-.-.-
Wichtige Hinweise
Handsender gehören nicht in Kinderhände!
Important
Keep hand transmitters out of reach of children at all times!
Handsender dürfen nun von Personen benutzt werden, die in die Funktionsweise der ferngesteuerten
Toranlage eingewiesen sind! Die Benutzung der Fernsteuerung muss mit Sichtkontakt zum Tor erfolgen! Die
Programmierung der Fernsteuerung ist immer in der Garage in Antriebsnähe vorzunehmen! Für die
Inbetriebnahme der Steuerung sind ausschliesslich Originalteile zu verwenden!
•
•
Die Geräte sind vor direkter Sonneneinstrahlung zu schützen!
Die Handsender sind vor Feuchtigkeit und Staubbelastung zu schützen!
Hand transmitters should only be used by persons who know to operate the remote controlled door system.
Only use the remote control when the door is in your line of vision! Always programme the remote control
inside the garage near the door operator. When putting the remote control into operation, use original
components only!
•
•
Protect equipment from direct sunlight.
Protect hand transmitters against dampness and dust.
Bei Nichtbeachtung kann durch einen Feuchtigkeitseintritt die Funktion beeinträchtigt werden!
If damp is allowed to penetrate through non-observance of the above, the function of the
unit can be seriously impaired.
Zulässige Umgebungstemperatur : -20C is +65C
Die örtlichen Gegebenheiten können Einfluss auf die Reichweite der Fernsteuerung haben!
Erweitern der Fernsteuerung mit weiteren Handsendern HS-SEU1, HS-SEU2, HS-SEU4 oder HS-SEU6
Hinweis : Ist kein seperater Zugang zur Garage vorhanden, so ist jede Änderung oder Erweiterung von
Programmierungen innerhalb der Garage durchzuführen. Bei der Programmierung und Erweiterung der
Fernsteuerung ist darauf zu achten, dass sich im Bewegungsbereich des Tores keine Personen und
Gegestände befinden.
1. Der Sender, der den Code „vererben“ soll (Vererbungssender) und den Sender, der den Code lernen
soll (Lernsender), direkt nebeneinander halten.
2. Die gewünschte Taste des Vererbungssenders drücken und gedrückt halten. Die LED des
Vererbungssenders leuchtet nun kontinuierlich.
3. Sofort danach die gewünschte zu lernende Taste des Lernsenders drücken und gedrückt halten – die
LED des Lernsenders blinkt zuerst für 4 Sek. langsam und beginnt bei erfolgreichem Lernvorgang
schneller zu blinken.
4. 4. Die Tasten vom Vererbungssender und vom Lernsender loslassen.
Eine Funktionsprüfung durchführen! Bei einer Fehlfunktion die Schritte 1 – 4 wiederholen.
Achtung! Während des Lernvorganges kann bei Betätigung des Vererbungssenders eine Torfahrt
ausgelöst werden, wenn sich ein darauf programmierter Empfänger in der Nähe befindet!
Hinweis : Wenn während des langsamen Blinkens die Taste des Lernsenders losgelassen wird, wird der
Lernvorgang abgebrochen.
Hörmann KG Verkaufsgesellschaft
D-33803 Steinhagen
Temperature range : -20C to +60C
Local conditions may affect the range of the remote control.
Extending the remote control set by adding further hand transmitters HS-SEU1, HS-SEU2,
HS-SEU4 or HS-SEU6
Note : If the garage does not have a seperate entrance, you should carry out any programming alterations
or expansion inside the garage. When programming or expanding the remote control set, ensure that no
persons or objects are within the door`s range of movement.
1. Hold the transmitter which is to „teach“ the code (teaching transmitter) and the transmitter which is to
learn the code (learning transmitter) directly alongside each other.
2. Press and hold the desired button on the teaching transmitter – the LED on the teaching transmitter now
glows continuously.
3. Immediately after having done this, press and hold the button which is to learn on the learning
transmitter – the LED on the learning transmitter initially flashes slowly for about 4 seconds, but then
starts flashing more rapidly once the learning procedure has been successfully completed.
4. Release the buttons on the teaching transmitter and learning transmitter.
Check that the transmitters are functioning correctly. If not, repeat steps 1 – 4.
CAUTION! Activation of the teaching transmitter during the learning procedure could set the
door in motion if there is an appropriately programmed receiver near to where you are
standing!
Note : The learning procedure will be aborted if you release the button on the learning transmitter during the
slow-flashing period.
Hörmann KG Verkaufsgesellschaft
D-33803 Steinhagen
Technische Mitteilung TM-EL20
Technical Bulletin TM-EL20
von
: Michael Lienenkämper
Author
: Michael Lienenkämper
Datum
: 17.11.06
Date
: 17.11.06
Verteiler
: Gruppe A, B, C, D, E, F
Distribution
: Gruppe A, B, C, D, E, F
über
: Funkempfänger
about
: Radio Remote Control
hier
: Steckplatine 868MHz, Programmieranleitung
here
: receiver on p.c.b. 868MHz, 1 channel
.-.-.-.-.-.-.-.-.-.-
.-.-.-.-.-.-.-.-.-.-
Hinweis : GSM900 Handys können bei gleichzeitiger Benutzung die Reichweite der Funkfernsteuerung
beeinflussen.
Note : GSM 900 mobile phones used at the same time may influence the range of the radio remote control.
1. Die rote Taste (Programmiertaster) am Empfänger kurz betätigen – die rote LED beginnt langsam zu
blinken.
2. Die gewünschte zu programmierende Taste des Handsenders mindestens 1 Sek. drücken. Der Abstand
zwischen dem Sender und dem Empfänger muss min. 1m betragen.
3. Bei erfolgter Programmierung beginnt die rote LED im Empfänger schneller zu blinken.
4. Die Taste des Handsenders loslassen.
1. Briefly press red button „P“ (programming button) on the receiver – the red LED starts flashing slowly.
2. Press the button you wish to programme on the hand transmitter for at least 1 second. The distance
between the transmitter and the receiver should be at least 1m.
3. When the programming has been completed, the red LED starts flashing more rapidly.
4. Release the button on the hand transmitter.
Nach Beendigung des Blinkens ist der Empfänger empfangsbereit.
Once the flashing stops, the receiver is ready for operation.
Zur Überprüfung ist die programmierte Taste des Senders zu betätigen, die rote LED des Empfängers
leuchtet auf.
To test the function, press the programmed button on the transmitter – the red LED lights up when the output
is active.
Hinweis : Wenn 30Sek. nach Druck auf den Programmiertaster keine Programmierung erfolgt, erlischt die
langsam blinkende rote LED im Empfänger wieder.
Note : If no programming is carried out within 30 seconds of processing the „P“-button, the slow flashing red
LED on the receiver goes out again.
Abbrechen der Programmierung : Wenn der Programmiertaster 3-mal kurz innerhalb von 2 Sek. betätigt
wird, erlischt die rote LED und der Programmiervorgang wird abgebrochen.
Aborting the programming procedure : If after pressing the programming button this is pressed 3 times
within 2 seconds, the red LED goes off and the programming procedure is aborted.
Empfang : Wenn der Empfänger die Sendecodes empfängt, wird der Signalausgang für 0,5 Sek. aktiv.
Während dieser Zeit leuchtet die LED am Empfänger.
Reception : When the receiver receives the transmitting codes that were programmed the signal output is
active for 0,5 seconds. During this time the LED on the receiver is on.
„P“-button
„P“-Taste
Hörmann KG Verkaufsgesellschaft
D-33803 Steinhagen
Hörmann KG Verkaufsgesellschaft
D-33803 Steinhagen
Wireless Impulse Transmission
Technical Data
Wireless Impulse Transmission
Technical Data
HOE_OPTOC_GB.DOC
1. Failure Diagnosis
1.2. OPT-CM 1163, #013550
1.1. OPT-CF 1163
%
YELLOW
Condition
active
Test
YELLOW
- wiring to control panel
Condition
Action
R
F
- change batteries
R
F
- none
2s
inactive
- wiring to control panel
safety edge activated
- wiring of safety edge
1s
2s
4 Hz
- mounting of safety edge
crash or missing light
transmission
RED
- alignment (straight way of light)
condition
Action
- change OPT-CM 1163
- optical axis interrupted
- dirt
- wiring Crash-Switch
- none
- batteries OPT-CM 1163
no operating voltage
RED
- wiring to control panel
condition
Action
- change OPT-CF 1163
- none
Hörmann KG Verkaufsgesellschaft
D-33803 Steinhagen
Hörmann KG Verkaufsgesellschaft
D-33803 Steinhagen
1.
2.
OPTOC_BAT.DOC

Источник