The store will not work correctly in the case when cookies are disabled.
Get support and advice for your Lay-Z-Spa AirJet or HydroJet pump Is there an E08 error code displaying on your Lay-Z-Spa AirJet or HydroJet pump? Check out this step-by-step troubleshooting guide we recommend. This guide will help you identify the cause and solution to solve this error code. Then if you still need assistance, this guide will direct you to our Customer Care team who are here to support you with any issues and get you back to enjoying your Lay-Z-Spa in no time.
Is there an E08 error code displaying on your Lay-Z-Spa pump? This means your Lay-Z-Spa pump is experiencing a power supply issue.
We recommend following these troubleshooting steps to get back in your Lay-Z-Spa in no time.
Step 1 — Complete thermal reset:
The pump will require a full thermal reset occasionally during the use of the spa. Please follow these steps making sure 10 seconds is left between each step:
- Turn Pump On
- Press Test – either on the PRCD or on the pump screen display
- Turn plug off and remove from socket
- Plug back in and turn on
- On the PRCD (black box) press: Reset → Test → Reset.
- Hold down the On / Off button on the pump for 5 seconds.
- Press thermal reset button (See picture for location of reset button on the final page)
- Press heater button – pump should be working with no error codes.
Here’s a link to our thermal reset video:
Step 2 — Check power supply:
Lay-Z-Spa pumps have to be plugged directly into a grounded mains supply. Please see the checklist below for further information:
Where is the item plugged into?
• Is the pump plugged into a single of double socket?
• Is the pump being used with an extension lead?
• Are there any other items plugged into the same socket?
• Is the plug socket outside? If so, is the socket waterproof?
• How old is the plug socket?
• Is the plug socket connected directly into the mains or is it a spur?
• Are there any other household items tripping?
• When was the last time the socket was tested by an electrician?
If the following steps provided above, do not resolve the issue please contact our Customer Care team below.
© 2021 Lay-Z-Spa. Company Registration No: 09476227. VAT No: GB 207409622
КОДЫ ОШИБОК
Состояния
Датчики расхода воды работают
без нажатия кнопки фильтрации
или подогрева.
После запуска или в процессе
фильтрации и (или) подогрева
датчики расхода воды не
обнаруживают потока воды.
Термометр насоса показывает
температуру воды ниже
4 °C (40°F).
Термометр насоса показывает
температуру воды выше
50 °C (122 °F).
Неполадки соединений
термометра насоса.
Неисправность ручного сброса
теплового выключателя
Протечка воды
внутри насоса.
Неисправность соединения
заземления.
Причины
1. Флажки датчиков расхода воды не вернулись в
правильное положение.
2. Датчики расхода воды сломаны.
1. Вы забыли снять два колпачка-заглушки внутри
бассейна.
2. Картриджи фильтров загрязнены.
3. Запустите систему фильтрации или подогрева и
поставьте руку перед выпускной трубой внутри
бассейна, чтобы проверить, вытекает ли вода.
a. Если вода не вытекает, это означает, что
водяной насос сломан.
б. Если вода вытекает, но появляется аварийный
сигнал
, это означает, что сломаны
датчики подачи воды.
4. Блокирование фильтра.
5. Согнутые трубки или слабый поток воды через
пластиковые трубки чаши
6. Заблокированы сетки для улавливания
засорений: сетки для улавливания засорений
могут блокироваться при высокой жесткости
воды за счет скопления на них известковых
отложений.
7. Пришедшие в негодность шайбы
Шайбы соединений спа-бассейна могут прийти в
негодность или износиться.
1. Температура воды ниже 4 °C (40 °F).
2. Если температура воды выше 7 °C (44,6 °F), то
термометр насоса поврежден.
1. Температура воды выше 50 °C (122 °F).
2. Если температура воды ниже 45 °C (113 °F), то
термометр насоса поврежден.
1. Соединители термометра насоса не функционируют
надлежащим образом.
2. Термометр насоса сломан.
Сработал ручной сброс теплового
выключателя.
Система обнаружила протечку воды
внутри насоса.
1. Проблемы с заземлением в вашем доме.
2. Какая-то неисправность насоса.
Способы устранения
1. Осторожно извлеките штепсельную вилку из розетки, ударьте по насосу
сбоку, но не сильно, и снова вставьте вилку в розетку.
2. Для получения помощи посетите раздел поддержки на нашем веб-сайте
www.bestwaycorp.com
1. Перед подогревом снимите два колпачка-заглушки; см. раздел «Сборка» в
руководстве пользователя.
2. Извлеките фильтрующий блок из бассейна и нажмите кнопку фильтрации
или подогрева. При отсутствии аварийных сигналов почистите или
замените картриджи фильтра и снова установите на место фильтрующий
блок.
3. Для получения помощи посетите раздел поддержки на нашем веб-сайте
www.bestwaycorp.com
4. Очистите фильтр и проверьте его на предмет повреждений. Замените или
установите старый на место, сообразно обстоятельствам. Для получения
помощи посетите раздел поддержки на нашем веб-сайте
www.bestwaycorp.com
5. Проверьте соединения спа-бассейна, чтобы выявить, не согнуты ли
трубки. Для получения помощи посетите раздел поддержки на нашем
веб-сайте www.bestwaycorp.com
6. Опорожните спа-бассейн и вставьте садовый шланг в трубки, чтобы
вымыть засорения. Чтобы убедиться, что все засорения вымыты,
выполните эту операцию как снаружи, так и изнутри спа-бассейна.
Въевшиеся засорения удалите с помощью зубной щетки. Для получения
помощи посетите раздел поддержки на нашем веб-сайте
www.bestwaycorp.com
7. Проверьте шайбы внутри соединений на предмет повреждений.
Раскрутите соединения и снимите шайбы для осмотра. Для получения
помощи посетите раздел поддержки на нашем веб-сайте
www.bestwaycorp.com
1. Бассейн не рассчитан на работу при температуре воды ниже 4 °C (40 °F).
Отсоедините насос от сети питания и перезапустите его, когда температура воды
достигнет 6 °C (43 °F).
2. Для получения помощи посетите раздел поддержки на нашем веб-сайте
www.bestwaycorp.com
1. Бассейн не рассчитан на работу при температуре воды выше 40 ºC (104 °F).
Отсоедините насос от сети питания и перезапустите его, когда температура воды будет 38
ºC (100 °F) или ниже.
ВАЖНО! Перед перезапуском насоса нажмите кнопку сброса насоса.
2. Для получения помощи посетите раздел поддержки на нашем веб-сайте
www.bestwaycorp.com
Для получения помощи посетите раздел поддержки на нашем веб-сайте
www.bestwaycorp.com
1. Отсоедините насос от сети питания и нажмите его кнопку сброса; затем снова
подсоедините насос к сети.
2. Если аварийный сигнал не выключится, обратитесь к разделу «КНОПКА
СБРОСА» в руководстве пользователя.
3. Для получения помощи посетите раздел поддержки на нашем веб-сайте
www.bestwaycorp.com
Для получения помощи посетите раздел поддержки на нашем веб-сайте
www.bestwaycorp.com
Для получения помощи посетите раздел поддержки на нашем веб-сайте
www.bestwaycorp.com
261
[100% fixed*] how to fix e08 error lazy spa (fixed)?
how-to-fix-e08-error-lazy-spa,how to fix e08 error lazy spa,e08 error lazy spa, fixed e08 error lazy spa,e08 error lazy spa fixed,e08 error code lazy spa,e08 error lazy spa, e08 error lazy spa,e08 error lazy spa, e08 error
Most pump problems area unit straightforward to mend and may typically be resolved in minutes. polishing off regular checks and maintenance will forestall persistent pump issues thus you’ll be able to retreat to to enjoying your Lay-Z-Spa.Get facilitate together with your Lay-Z-Spa pump. resolve the causes and therefore the solutions to pump error codes, screaming pump problems, heating issues and far a lot of.
Is there associate degree E08 error code displaying on your Lay-Z-Spa pump? this implies your Lay-Z-Spa pump is experiencing an influence provide issue.
[Fixed*] how to fix e08 error lazy spa (100% fixed)?
Solution:-01-Complete thermal reset:
The pump would force a full thermal reset often throughout the utilisation of the spa. Please follow these steps making positive ten seconds is left between every step:
✔️Turn Pump On
✔️Press check – either on the PRCD or on the pump screen show
✔️Turn plug off and take away from socket
✔️Plug back in and switch on
✔️On the PRCD (black box) press: Reset check check → Reset.
✔️Hold down the On / Off button on the pump for five(5) seconds.
✔️Press thermal push button (See image for location of push button on the ultimate page)
✔️Press heater button – pump ought to be operating with no error codes.
Solution:-02- Check power supply:
Lay‑Z‑Spa pumps have to be compelled to be obstructed directly into a grounded mains provide. Please see the list below for any information:
Where is that the item obstructed into?
• is that the pump obstructed into one of double socket?
• is that the pump being employed with associate degree extension lead?
• area unit there the other things obstructed into identical socket?
• is that the plug thus socket outside? If so, is that the socket waterproof?
• however recent is that the plug socket?
• is that the plug socket connected directly into the mains or is it a spur?
• area unit there the other home items tripping?
• once was the last time the socket was tested by associate degree electrician?
Solution:-03- E08 is detective work that switch is circuit, thus suggests the switch or wiring thereto is faulty.
You need to strip it down and check if the wire has come back lose, you’ll be able to check it for continuity with a multi meter if its circuit you would like to shop for a replacement switch if its not then you would like to examine the wiring.
If all the wiring is sound it points to a faulty PCB, wherever its incorrectly detective work the thermal fuse has tripped
Solution:-04-Contact customer care
Click here to visit official website for tech support
Conclusion:-The pump would force a full thermal reset often throughout the utilisation of the spa. E08. The thermostat desires resetting. flip the pump unit on at the mains. Press the check button once and leave it bleeping (leave for ten seconds).Thank you.
There may be a number of reasons why your heater pump is displaying an error code. The following is a list of error codes, the reason behind them and how they can be solved.
Select Your Error Code:
E01 E02 E03 E04E05 E06 E07 E08 E09 E10 E11 E12 E13 GCF backwash
E01
← swipe →
| Description | Cause | Solution |
|---|---|---|
| Sensor Error | The water flow sensors’ flags didn’t come back into the correct position. | Unplug the pump unit, lightly strike the side of it and then plug it back in.
If the unit does not respond, try rolling the pump unit on its side in order to shift the sensor placement. |
| Water Flow Error | Electrical issue. Can occur when the spa is not plugged into a mains socket. May also be an issue with the RCD socket. | Plug the pump unit directly into a mains socket and not into an extension lead. |
| Debris Build Up | Issue with water flora sensors due to debris build up. | Please follow the backwash procedure in the video here |
E01 Error Code Troubleshooting download
E02
← swipe →
| Description | Cause | Solution |
|---|---|---|
| Water Flow Error | The stopper caps are still inside the spa. | Remove the black stopper caps from the inside of the liner before heating, filtering or running the bubbles on the spa. If you are unsure how to remove them, please refer to the assembly section within the Lay-Z-Spa owners manual. |
| Filter cartridges are dirty | Remove the filter cartridge from the filter housing and check it is clean. Please make sure the new filter is clean and dry before you install it. | |
| Filter housing is restricting flow | Remove the filter housing from the liner and check the black membrane inside. These should lie flat inside the housing. If they are ok, continue to run the spa without the filter cartridge attached and see if the error code persists. | |
| Ensure that the debris screens are clear of debris. | ||
| Pipes within the liner are kinked or bent. | Disconnect the pump and check the pipes inside the liner. You can manipulate these with warm water to return them to the correct shape. | |
| Washers perished inside pump couplings | Disconnect the pump from the liner. Check the condition of washers inside the couplings on the pump. We would suggest backwashing the pump to clear any debris. If the washers are perished you can purchase spares from the Lay-Z-Spa website here | |
| Water flow sensors not working | If the above troubleshooting has not resolved the problem, the water flow sensors may not be working. Please contact us for more help with this |
E02 Error Code Troubleshooting download
E03
← swipe →
| Description | Cause | Solution |
|---|---|---|
| Temperature too low | The pump will only operate when the ambient temperature is above 4°C. We would suggest disconnecting the pump and moving it to a warmer place. You will need to do the thermal reset procedure before continuing use. | The pump will only operate when the ambient temperature is above 4ºC. |
| The pump thermometer is broken. | If your pump is displaying this message and the ambient temperature is above 4ºC. Please contact us for more help. |
E03 Error Code Troubleshooting download
E04
← swipe →
| Description | Cause | Solution |
|---|---|---|
| Temperature too high | The pump unit has overheated. | Place the stoppers caps inside the spa and disconnect the pump unit. Allow time for the pump unit to cool down before connecting again. |
| The water temperature is over 50ºC (122ºF). | The Lay-Z-Spa is not designed to operate with water temperatures exceeding 40ºC (104ºF). Unplug the pump and plug it back in once the water temperature has reached 38ºC (100ºF) or lower. IMPORTANT: Before you restart the pump, press the reset button. | |
| The thermostat needs resetting. |
|
E04 Error Code Troubleshooting download
E05
← swipe →
| Description | Cause | Solution |
|---|---|---|
| Temperature too high | The thermostat is broken. | If the troubleshooting has been completed without success, please contact us for more help with this |
| Pump needs to be reset. |
|
|
| Pump unit needs to be cleaned | Try the back wash procedure. | |
| Not enough power to the pump. | Ensure the pump unit is plugged into a mains socket and not an extension lead. |
E05 Error Code Troubleshooting download
E06
← swipe →
| Description | Cause | Solution |
|---|---|---|
| Electrical Fault | The power port has experienced a temporary current variation. | Unplug the pump and hen plug it back in. Please ensure the pump unit is plugged into a mains socket and not an extension lead. |
E06 Error Code Troubleshooting download
E07
← swipe →
| Description | Cause | Solution |
|---|---|---|
| Electrical Fault | The pump has read an electrical error. | Try the reset procedure detailed in the troubleshooting document. If the troubleshooting has been completed without success, please contact us for more help. |
E07 Error Code Troubleshooting download
E08
← swipe →
| Description | Cause | Solution |
|---|---|---|
| The thermostat needs resetting. |
|
E08 Error Code Troubleshooting download
E09
← swipe →
| Description | Cause | Solution |
|---|---|---|
| Fuse Failure. | Internal fuse failure or has become disconnected within the pump. |
|
E09 Error Code Troubleshooting download
E10
← swipe →
| Description | Cause | Solution |
|---|---|---|
| High salt alarm. | Alarm where too much salt has been added to the spa or a large amount of water has evaporated. |
|
E10-E11 Error Code Troubleshooting download
E11
← swipe →
| Description | Cause | Solution |
|---|---|---|
| Low salt alarm. | Alarm for low salt levels within the spa. This means the spa requires further salt to be added. |
|
E10-E11 Error Code Troubleshooting download
E12
← swipe →
| Description | Cause | Solution |
|---|---|---|
| Water Leakage. | Error code for an issue with water leaking within the body of the pump. |
|
E12-E13 Error Code Troubleshooting download
E13
← swipe →
| Description | Cause | Solution |
|---|---|---|
| Signal within the pump. | Error code for issue where the electrical signal within the pump body between the control panel and power board has become disconnected. |
|
E12-E13 Error Code Troubleshooting download
GCF
← swipe →
| Description | Cause | Solution |
|---|---|---|
| Not grounded/earthed correctly | An issue with your power supply | Remove any extension leads, we do not recommend the pump is run on one of these. Also try the pump in an alternative socket. If the issue persists, please contact us for further advice. |
Backwash Procedure
Attach the stopper caps to the inside of the liner and then remove the Lay-Z-Spa pump unit from the liner (you can do this by unscrewing the 3 couplings ‘A, B and C’).
Using a hosepipe, flush water backwards through the pump. Water should go through pipe ‘B’ and come out of pipe ‘C’.
After a few minutes, flush the water in the opposite direction for about 2 minutes (through pipe ‘C’ and out of pipe ‘B’).
If you have a Hydro Jet Lay-Z-Spa, unfortunately, the backwash procedure will be a little tricky. These are not constructed like the other models of the Lay-Z-Spa. please contact us
The E08 error is a sign that the switch is faulty or isn’t working properly. To fix this problem, you should look at the wiring, check for continuity, and buy a new switch if necessary. If that doesn’t work, you can reset the controller.
Ensure that the debris screens are clear of debris
When using a Lay-Z-Spa, make sure that the debris screens are clear of debris. These screens will prevent debris from entering the pump. If any of the screens become damaged, you can purchase a replacement. It is important to note that the Lay-Z-Spa comes with two Debris Screens. Ensure that these screens are clear of debris before you begin using the spa.
Ensure that the cover is in a dry, clean location. This is necessary to prevent the cover from picking up dirt and bacteria. Be sure not to place the cover directly on the ground, since this could bleach the wood. If you are storing your spa at home, consider using cover lifters.
Ensure that children under five do not play near the spa. The risk of accidental drowning is much higher in this age group. To prevent this problem, make sure there is an adult supervising them at all times. Installing a safety protection device to your spa can help prevent accidental drowning.
Check the water flow sensors’ flags
If you encounter an e08 error code on your Lazy Spa, you should first check the water flow sensors. This code is often caused by the water flow sensors in the spa not returning to their normal position. To solve this error, unplug the pump unit, lightly strike the sensor and plug it back in to reset the pump. If this doesn’t work, you should call the manufacturer or the service organization for help.
Another possible cause of the error is an electrical fault or a malfunctioning sensor. To repair this, you will need to unplug the pump from the mains and check the water flow sensor flags. Once you’ve checked them, you can then reconnect the pump to the mains. Remember to do this in an upright position so that the pump can’t draw too much current.
To test the water flow sensors, you will need a multimeter. Set the meter to the continuity setting so you can see if the sensor is open or short. Alternatively, you can use the resistance setting on the meter. In this case, you should see either zero or infinite resistance. Make sure you use a stiff wire to connect the multimeter to the water flow sensor. Next, you should wrap a small wire around the test probe and insert it into the connector holes.
Check the digital temperature sensor in the heater or pool
This error code can also be caused by a problem with the heater housing. If the temperature inside the heater housing is lower than 40 degrees Fahrenheit, the circ pump will run at low speed. It’s likely that a damaged or disconnected temperature sensor is to blame. You can try resetting the heater or pool to see if this fixes the problem. If this doesn’t work, contact your spa pool supplier to learn how to fix the issue.
The first step in fixing the E08 error on a Lay-Z-Spa is to check the temperature of the water. If it exceeds 40 degrees Celsius, the temperature is too high. If this is the case, you need to use appropriate water chemicals. Also, you should check the pH level of the water. If it’s too high, you will need to lower the temperature to lower the pH level.
Another possible cause is a dirty filter or a dirty pump impeller. This may be causing the error code. If you can’t figure out why the error code is appearing, then you need to check the filter.
Reset the controller
If your spa is giving an E08 error message, there are a few things you can do to fix the problem. The first thing you need to do is isolate the power supply to the spa controller. To do this, you need to remove the cover over the spa pack enclosure and turn off the mains power. If the spa does not turn on, you can check the power supply by checking the heartbeat LED light. If this is not working, you need to reset the controller.
If the temperature sensor is displaying a significantly different number than the other two, it may be indicating a problem with the flow. If the temperature sensors do not match, you can try to reconnect them or reset the real time clock. If the problem persists, you may need to contact your spa supplier for more assistance. You can also try to replace the temperature sensor. It is not uncommon for this error message to occur if the water temperature sensor is damaged or disconnected.
A Lay-Z-Spa pump can experience many problems. However, the good news is that you can fix them quickly and easily. By following these steps, you can ensure your hot tub keeps the proper temperature.