Интенсивная эксплуатация спецтехники марки Bobcat невозможна без поломок и сбоев в работе. Основные дефекты связаны с выходом из строев узлов и агрегатов вследствие больших нагрузок и длительного использования. При наличии большого опыта и знаний оператор или механик может выявить истинную причину поломки по внешним признакам. Во многих случаях разобраться со сложной техникой помогут коды ошибок Бобкэт на панели управления.
При возникновении ошибок на панели управления погрузчиков марки Bobcat обращение в компанию АнгараГрупп – отличный вариант для своевременной диагностики и ремонта техники.
При появлении соответствующей индикации на панели приборов, водитель должен немедленно прекратить работу, обратиться к механику или сразу в сервисный центр. Квалифицированные инженеры помогут быстро и качественно устранить дефект с минимальными затратами.
нейтральном положении
замкнут на землю
замкнут на землю
замкнут на батарею
замкнут на батарею
землю
землю
батарею
батарею
механизма подъема ACS (AHC)
механизма наклона ACS (AHC)
механизма подъема ACS (AHC)
механизма наклона ACS (AHC)
батарею
допустимых пределов
пределов
работы
(AHC)
землю
батарею
допустимых пределов
(AHC)
управления, ACS (AHC)
положении
положении
положении
Идентификация ошибок Бобкэт S530 позволяет быстро выявить проблемы с исполнительными механизмами, провести техническое обслуживание и ремонт агрегатов. Подобные мероприятия помогают оперативно устранить дефекты и продлить срок эксплуатации погрузчиков. Стандартными ошибками погрузчиков данной модели являются:
Актуальные коды ошибок Bobcat S175 приведены в руководстве по эксплуатации техники. На панель приборов выведены цифровые индикаторы предупреждения о внештатных ситуациях в работе погрузчика. Наиболее частыми являются следующие ошибки Бобкэт 175:
Указанные ошибки Бобкэт S175 не являются единственными. В инструкции по эксплуатации приведены все возможные индикации и предупреждения. Для собственника техники или водителя знание основных ошибок облегчает диагностику, помогает принять решение о дальнейших действиях в плане техобслуживания и ремонта.
Инженеры сервисного центра обладают большим опытом и высокой квалификацией, быстро найдут корневую причину проблемы и предложат варианты ее решения.
Для владельцев погрузчиков данной марки обращение к нам – это возможность отремонтировать агрегаты погрузчиков оперативно и с предоставлением гарантии, в том числе с выездом специалистов сервисного центра на площадку клиента.
Коды ошибок мини погрузчиков Bobcat помогут вам идентифицировать неисправный исполнительный механизм и быстрее произвести ремонт отказавшего механизма как ДВС, так и гидравлической системы
Расшифровка кодов ошибок Bobcat
КОД | ОПИСАНИЕ |
01-16 | Не подсоединен воздушный фильтр |
01-17 | Засорен воздушный фильтр |
02-16 | Не подсоединен гидравлический нагнетательный фильтр |
02-17 | Засорен гидравлический нагнетательный фильтр |
03-09 | Низкое напряжение аккумуляторной батареи |
03-10 | Высокое напряжение аккумуляторной батареи |
03-11 | Предельно высокое напряжение аккумуляторной батареи |
03-14 | Предельно низкое напряжение аккумуляторной батареи |
03-22 | Напряжение аккумуляторной батареи ниже предельно допустимого |
04-09 | Низкий уровень давления масла в двигателе |
04-14 | Предельно низкий уровень давления масла в двигателе |
04-15 | Давление масла в двигателе на уровне экстренного выключения двигателя |
04-21 | Давление масла в двигателе выше предельно допустимого |
04-22 | Давление масла в двигателе ниже предельно допустимого |
05-09 | Низкое давление подпитки в гидравлической системе |
05-14 | Предельно низкое давление подпитки в гидравлической системе |
05-15 | Давление подпитки в гидравлической системе на уровне экстренного выключения двигателя |
05-21 | Давление подпитки в гидравлической системе выше предельно допустимого |
05-22 | Давление подпитки в гидравлической системе ниже предельно допустимого |
06-10 | Высокие обороты двигателя |
06-11 | Предельно высокие обороты двигателя |
06-13 | Отсутствует сигнал оборотов двигателя |
06-15 | Обороты двигателя на уровне экстренного выключения двигателя |
06-18 | Обороты двигателя вне допустимых пределов |
07-10 | Высокая температура масла в гидравлической системе |
07-11 | Предельно высокая температура масла в гидравлической системе |
07-15 | Температура масла в гидравлической системе на уровне экстренного выключения двигателя |
07-21 | Температура масла в гидравлической системе выше предельно допустимой |
07-22 | Температура масла в гидравлической системе ниже предельно допустимой |
08-10 | Высокая температура охлаждающей жидкости двигателя |
08-11 | Предельно высокая температура охлаждающей жидкости двигателя |
08-15 | Температура охлаждающей жидкости двигателя на уровне экстренного выключения двигателя |
08-21 | Температура охлаждающей жидкости двигателя выше предельно допустимой |
08-22 | Температура охлаждающей жидкости двигателя ниже предельно допустимой |
09-09 | Низкий уровень топлива |
09-21 | Уровень топлива выше предельно допустимого |
09-22 | Уровень топлива ниже предельно допустимого |
11-05 | Датчик рамы безопасности замкнут на батарею |
11-06 | Датчик рамы безопасности замкнут на массу |
12-21 | Сигнал ШИМ-контроллера передней доп. гидравлики за верхней границей диапазона |
12-22 | ШИМ-контроллер передней доп. гидравлики за нижней границей диапазона |
12-23 | ШИМ-контроллер передней доп. гидравлики не в нейтральном положении |
13-05 | Удерживающий соленоид отсечки топлива замкнут на батарею |
13-06 | Удерживающий соленоид отсечки топлива замкнут на массу |
13-07 | Разрыв цепи соленоида отсечки топлива |
14-02 | Втягивающий соленоид отсечки топлива, ошибочное включение |
14-03 | Втягивающий соленоид отсечки топлива, ошибочное выключение |
15-02 | Втягивающий соленоид блокировки тяги, ошибочное включение |
15-03 | Втягивающий соленоид блокировки тяги, ошибочное выключение |
16-05 | Удерживающий соленоид блокировки тяги замкнут на батарею |
16-06 | Удерживающий соленоид блокировки тяги замкнут на массу |
16-07 | Разрыв цепи удерживающего соленоида блокировки тяги |
17-05 | Соленоид гидравлического запорного клапана замкнут на батарею |
17-06 | Соленоид гидравлического запорного клапана замкнут на массу |
17-07 | Разрыв цепи соленоида гидравлического запорного клапана |
18-05 | Соленоид золотника замкнут на батарею |
18-06 | Соленоид золотника замкнут на массу |
18-07 | Разрыв цепи соленоида золотника |
19-02 | Соленоид позиционирования ковша, ошибочное включение |
19-03 | Соленоид позиционирования ковша, ошибочное выключение |
20-02 | Соленоид переключения скоростей, ошибочное включение |
20-03 | Соленоид переключения скоростей, ошибочное выключение |
21-02 | Свечи накаливания, ошибочное включение |
21-03 | Свечи накаливания, ошибочное выключение |
22-02 | Стартер, ошибочное включение |
22-03 | Стартер, ошибочное выключение |
23-02 | Задний базовый соленоид, ошибочное включение |
23-03 | Задний базовый соленоид, ошибочное выключение |
24-02 | Задний штоковый соленоид, ошибочное включение |
24-03 | Задний штоковый соленоид, ошибочное выключение |
25-02 | Задний вспомогательный пропорциональный соленоид, ошибочное включение |
25-03 | Задний вспомогательный пропорциональный соленоид, ошибочное выключение |
26-02 | Ошибочное включение переднего базового соленоида |
26-03 | Ошибочное выключение переднего базового соленоида |
27-02 | Ошибочное включение переднего штокового соленоида |
27-03 | Ошибочное выключение переднего штокового соленоида |
28-02 | Ошибочное включение соленоида дивертера |
28-03 | Ошибочное выключение соленоида дивертера |
29-02 | Соленоид большой подачи, ошибочное включение |
29-03 | Соленоид большой подачи, ошибочное выключение |
30-28 | Отказ памяти контроллера |
31-28 | Неисправность режима восстановления |
32-04 | Расширенное управление (ACS) не сообщается с контроллером Bobcat |
32-23 | Расширенное управление ACS не откалибровано |
32-31 | Отказ исполнительного механизма наклона |
32-32 | Неисправность электропроводки исполнительного механизма наклона |
32-33 | Неисправность электропроводки рукоятки наклона ковша |
32-34 | Исполнительный механизм наклона не в нейтральном положении |
32-35 | Рукоятка / педаль наклона ковша не в нейтральном положении |
32-36 | Отказ исполнительного механизма подъема |
32-37 | Неисправность электропроводки исполнительного механизма подъема |
32-38 | Неисправность электропроводки рукоятки подъема стрелы |
32-39 | Исполнительный механизм подъема не в нейтральном положении |
32-40 | Рукоятка / педаль подъема стрелы не в нейтральном положении |
32-41 | Нет связи |
32-49 | Исполнительный механизм подъема замкнут на массу |
32-50 | Исполнительный механизм наклона замкнут на массу |
32-51 | Исполнительный механизм подъема замкнут на батарею |
32-52 | Исполнительный механизм наклона замкнут на батарею |
32-53 | Рукоятка / педаль подъема стрелы замкнута на массу |
32-54 | Рукоятка / педаль наклона ковша замкнута на массу |
32-55 | Рукоятка / педаль подъема стрелы замкнута на батарею |
32-56 | Рукоятка / педаль наклона ковша замкнута на батарею |
32-57 | Пониженная производительность исполнительного механизма подъема |
32-58 | Пониженная производительность исполнительного механизма наклона |
32-59 | Неправильное направление исполнительного механизма подъема |
32-60 | Неправильное направление исполнительного механизма наклона |
32-61 | Блокиратор рукояток замкнут на массу |
32-62 | Блокиратор рукояток замкнут на батарею |
32-63 | Цепь блокиратора педалей замкнута на массу |
32-64 | Цепь блокиратора педалей замкнута на батарею |
32-65 | Напряжение питания датчика вне допустимых пределов |
32-66 | Напряжение аккумуляторной батареи вне допустимых пределов |
32-67 | Переключатель переключился во время работы |
32-68 | Информационная ошибка рукоятки подъема стрелы |
32-69 | Переключатель режимов управления переключился во время работы |
32-70 | Цепь правой рукоятки движения замкнута на массу |
32-71 | Цепь правой рукоятки движения замкнута на батарею |
33-23 | Главный контроллер (контроллер Bobcat) не запрограммирован |
34-04 | Панель с кнопочным запуском не сообщается с контроллером Bobcat |
35-02 | Двухскоростной переключатель вентилятора, ошибочное включение |
35-03 | Двухскоростной переключатель вентилятора, ошибочное выключение |
36-48 | Подключено несколько контроллеров ACD |
37-02 | Двухскоростной дополнительный переключатель скоростей, ошибочное включение |
37-03 | Двухскоростной дополнительный переключатель скоростей, ошибочное выключение |
38-04 | Нет связи с контроллером джойстика |
38-05 | Ось Х левого джойстика не в нейтральном положении |
38-06 | Ось X правого джойстика не в нейтральном положении |
38-07 | Ось Y левого джойстика не в нейтральном положении |
38-08 | Ось Y правого джойстика не в нейтральном положении |
38-09 | Переключатель режимов управления — замыкание на батарею или на массу |
38-11 | Исполнительный механизм подъема не в нейтральном положении |
38-12 | Исполнительный механизм наклона не в нейтральном положении |
38-13 | Отказ исполнительного механизма подъема |
38-14 | Отказ исполнительного механизма наклона |
38-15 | Неисправность проводки управления скоростью правого колеса |
38-16 | Неисправность проводки для скорости левого колеса |
38-17 | Пониженная производительность исполнительного механизма наклона |
38-18 | Пониженная производительность исполнительного механизма подъема |
38-19 | Ось X левого джойстика, за верхней границей диапазона |
38-20 | Ось X правого джойстика, за нижней границей диапазона |
38-21 | Ось Y левого джойстика, за верхней границей диапазона |
38-22 | Ось Y правого джойстика, за верхней границей диапазона |
38-23 | Сигнал переднего правого датчика управления за верхней границей диапазона |
38-24 | Сигнал переднего левого датчика управления за верхней границей диапазона |
38-25 | Сигнал заднего правого датчика управления за верхней границей диапазона |
38-26 | Сигнал заднего левого датчика управления за верхней границей диапазона |
38-27 | Сигнал исполнительного механизма подъема за верхней границей диапазона |
38-28 | Сигнал исполнительного механизма наклона за верхней границей диапазона |
38-29 | Ось X левого джойстика, за нижней границей диапазона |
38-30 | Ось X правого джойстика, за нижней границей диапазона |
38-31 | Ось Y левого джойстика, за нижней границей диапазона |
38-32 | Ось Y правого джойстика, за нижней границей диапазона |
38-33 | Сигнал переднего правого датчика управления за нижней границей диапазона |
38-34 | Сигнал переднего левого датчика управления за нижней границей диапазона |
38-35 | Сигнал заднего правого датчика управления за нижней границей диапазона |
38-36 | Сигнал заднего левого датчика управления за нижней границей диапазона |
38-37 | Питание «1» 5-вольтового датчика, за нижней границей диапазона |
38-38 | Питание «2» 5-вольтового датчика, за нижней границей диапазона |
38-39 | Исполнительный механизм подъема замкнут на массу / за нижней границей диапазона |
38-40 | Исполнительный механизм наклона замкнут на массу / сигнал за нижней границей диапазона |
38-41 | Неправильное направление исполнительного механизма наклона |
38-42 | Неправильное направление исполнительного механизма подъема |
38-43 | Соленоид левого переднего привода, ошибочное включение |
38-44 | Соленоид левого реверсивного привода, ошибочное включение |
38-45 | Соленоид правого переднего привода, ошибочное включение |
38-46 | Соленоид правого реверсивного привода, ошибочное включение |
38-47 | Передний правый соленоид управления, ошибочное включение |
38-48 | Передний левый соленоид управления, ошибочное включение |
38-49 | Задний правый соленоид управления, ошибочное включение |
38-50 | Задний левый соленоид управления, ошибочное включение |
38-51 | Соленоид давления системы управления, ошибочное включение |
38-52 | Сигнал заднего хода, ошибочное включение |
38-53 | Соленоид левого переднего привода, ошибочное выключение |
38-54 | Соленоид левого реверсивного привода, ошибочное выключение |
38-55 | Соленоид правого переднего привода, ошибочное выключение |
38-56 | Соленоид правого реверсивного привода, ошибочное выключение |
38-57 | Передний правый соленоид управления выдвижением, ошибочное выключение |
38-58 | Передний правый соленоид управления втягиванием, ошибочное выключение |
38-59 | Передний левый соленоид управления выдвижением, ошибочное выключение |
38-60 | Передний левый соленоид управления втягиванием, ошибочное выключение |
38-61 | Задний правый соленоид управления выдвижением, ошибочное выключение |
38-62 | Задний правый соленоид управления втягиванием, ошибочное выключение |
38-63 | Задний левый соленоид управления выдвижением, ошибочное выключение |
38-64 | Задний левый соленоид управления втягиванием, ошибочное выключение |
38-65 | Соленоид давления системы управления, ошибочное выключение |
38-66 | Сигнал заднего хода, ошибочное выключение |
38-67 | Нет сообщений от контроллера Bobcat |
38-68 | Углы установки колес (выравнивание) не откалиброваны |
38-69 | Исполнительные механизмы подъема и наклона не откалиброваны |
38-70 | Отключение питания |
38-71 | Напряжение батареи вне допустимых пределов |
38-72 | Насос привода не откалиброван |
38-73 | Переключатель режима управления/режима движения переключился во время работы |
38-74 | Скорость неуправляемого правого колеса, ошибочное включение |
38-75 | Скорость неуправляемого левого колеса, ошибочное включение |
38-76 | Соленоид давления системы управления — недостаточный ток |
38-77 | Передний правый соленоид управления выдвижением — недостаточный ток |
38-78 | Передний правый соленоид управления втягиванием — недостаточный ток |
38-79 | Передний левый соленоид управления выдвижением — недостаточный ток |
38-80 | Передний левый соленоид управления втягиванием — недостаточный ток |
38-81 | Задний правый соленоид управления выдвижением — недостаточный ток |
38-82 | Задний правый соленоид управления втягиванием — недостаточный ток |
38-83 | Задний левый соленоид управления выдвижением — недостаточный ток |
38-84 | Задний левый соленоид управления втягиванием — недостаточный ток |
38-85 | Питание «1» 5-вольтового датчика за верхней границей диапазона |
38-86 | Питание «2» 5-вольтового датчика за верхней границей диапазона |
38-87 | Блокировка правого переднего колеса (механическая неисправность управления) |
38-88 | Блокировка левого переднего колеса (механическая неисправность управления) |
38-89 | Блокировка правого заднего колеса (механическая неисправность управления) |
38-90 | Ошибка заднего левого управления |
38-91 | Отсутствуют импульсы датчика скорости правого колеса |
38-92 | Отсутствуют импульсы датчика скорости левого колеса |
38-93 | Датчик скорости правого колеса не отвечает |
38-94 | Датчик скорости левого колеса не отвечает |
38-98 | Контроллер в режиме калибровки привода |
38-99 | Контроллер в режиме калибровки положения колеса |
45-03 | Правый указатель поворота, ошибочное выключение |
46-02 | Левый указатель поворота, ошибочное включение |
46-03 | Левый указатель поворота, ошибочное выключение |
47-21 | Питание 8-вольтового датчика за верхней границей диапазона |
47-22 | Питание 8-вольтового датчика, за нижней границей диапазона |
48-02 | Реле переднего света, ошибочное включение |
48-03 | Реле переднего света, ошибочное выключение |
49-02 | Реле заднего света, ошибочное включение |
49-03 | Реле заднего света, ошибочное выключение |
60-21 | Сигнал рычага управления задней доп. гидравликой за верхней границей диапазона |
60-22 | Сигнал рычага управления задней доп. гидравликой за нижней границей диапазона |
60-23 | Рычаг управления задней доп. гидравликой не возвращается в нейтральное положение |
64-02 | Ошибочное включение реле мощности |
64-03 | Ошибочное выключение реле мощности |
74-72 | Сбой загрузочного кода контроллера Bobcat |
74-73 | Левая панель, ошибка приемного устройства |
80-02 | ACD, выход «A», ошибочное включение |
80-03 | ACD, выход «A», ошибочное выключение |
81-02 | ACD, выход «B», ошибочное включение |
81-03 | ACD, выход «B», ошибочное выключение |
82-02 | ACD, выход «C», ошибочное включение |
82-03 | ACD, выход «C», ошибочное выключение |
83-02 | ACD, выход «D», ошибочное включение |
83-03 | ACD, выход «D», ошибочное выключение |
84-02 | ACD, выход «E», ошибочное включение |
84-03 | ACD, выход «E», ошибочное выключение |
90-02 | Сервисный выход «C», ошибочное включение |
90-03 | Сервисный выход «C», ошибочное выключение |
91-02 | Сервисный выход «D», ошибочное включение |
91-03 | Сервисный выход «D», ошибочное выключение |
92-02 | Сервисный выход «Е», ошибочное включение |
92-03 | Сервисный выход «Е», ошибочное выключение |
93-02 | Сервисный выход «F», ошибочное включение |
93-03 | Сервисный выход «F», ошибочное выключение |
Мини-погрузчики – это отличная основа для различного навесного оборудования, разновидностей которого насчитывается около 40 приспособлений. При этом замена агрегатов составляет считанные секунды. Но любая техника нуждается в обслуживании, что и продлевает ее срок службы. Ремонт или покупка запчастей для погрузчиков Bobcat могут быть необходимы при поломках по таким причинам:
Внимание! Большая ошибка – продолжать использование техники при обнаружении проблем, появлении нехарактерных звуков.
Сервисное обслуживание
Компания Bobcat уже несколько десятилетий производит качественную, надежную и простую в эксплуатацию специализированную технику. Погрузчики сочетают в себе необходимую мощность и в то же время компактность. В таких конструкциях применяются современные системы управления, диагностики и элементы гидравлики.
Обнаружив проблемы в работе техники, необходимо воспользоваться квалифицированной помощью специалиста. При грамотном подходе можно некоторые поломки устранить самостоятельно, для этого понадобятся инструменты и необходимые запчасти для Bobcat. Компания позаботилась об ассортименте продукции и производит технику для уборки территории, погрузочных работ, для использования в сельском хозяйстве, ЖКХ и строительстве.
Важно! Для каждой модели техники предусмотрена инструкция, которую необходимо внимательно изучить.
Работа сервисных служб заключается в:
Это может быть замена технических жидкостей или вышедших из строя запчастей, ремонт отдельных узлов или навесного оборудования.
Рекомендации по эксплуатации
Одной из причин возникновения неисправностей может служить привлечение неопытного оператора, который, управляя машиной, создал неподходящий режим эксплуатации для техники. При управлении погрузчиком не может быть абсолютно всегда обеспечено выполнение четких стандартных действий. Возникают нештатные ситуации, в которых необходимо быстро принимать решения. Если они неверные, то в итоге ломаются основные узлы погрузчика или дополнительное оборудование.
Важно! Перед работой необходима проверка смазки узлов в трущихся деталях Bobcat, наличия масла, заряда АКБ, уровня охлаждающей жидкости в ДВС, давления в шинах, протяжки стяжных болтов и ступичных гаек на колесах. Каждую неделю необходима продувка радиатора и воздушного фильтра.
Поломка техники может быть связана и с плохим качеством дорог, особенно при превышении рекомендованной скорости. Возникают нежелательные вибрации, толчки, которые приводят к ускоренному износу узлов ходовой части. Не выполненная вовремя смазка может привести к деформации рулевого моста.
Замена запчастей Bobcat, узлов и деталей может понадобиться при дефектах:
Периодичность технического обслуживания позволит избежать серьезных проблем. В погрузчике каждые 250 часов работы нужно менять масло в двигателе, масляный фильтр, а каждые 1000 часов выполнять замену всех технических жидкостей и фильтров.
Ремонт и обслуживание
Согласно статистике, чаще всего неисправности происходят в топливной системе. Для того чтобы этого избежать, необходимо:
В топливную систему может попадать конденсат, это происходит в сезоны резких перепадов температур. По причине воздействия влаги могут возникнуть повреждения топливного насоса высокого давления и форсунок (в дизельном погрузчике). В бензиновом для исправления ситуации перебирают и просушивают детали карбюратора и полностью меняют топливо.
Радиатор погрузчика нуждается в продувке и промывке, особенно если эксплуатация проходит в запыленных помещениях. Возможно, могут понадобиться и дополнительные приспособления для фильтрации воздуха, которые можно приобрести в магазинах, реализующих оригинальные запчасти, например, snabavto. com.
Какие еще могут возникать проблемы:
Может подойти один из способов решения:
Возможно, неисправна система охлаждения, если постоянно высокая температура масла и образуется пена.
Важно! Запрещено работать на погрузчике без тормозов до устранения неисправностей.
Справка. Все оригинальные запчасти для Bobcat можно приобрести в различных компаниях, которые являются дистрибьюторами сертифицированной продукции, например, «Снабавто».
С чем это может быть связано:
Снижение эффективности погрузчика может быть связано с неправильной эксплуатацией АКБ, чтобы этого избежать, нужно:
Техника, в том числе погрузчики «Бобкэт», будет работать долго и исправно, если использовать ее правильно и осуществлять постоянный контроль над всеми ее системами, принимая своевременные меры по устранению дефектов.
Bobcat S650 Codes
Below are 46 working coupons for Bobcat S650 Codes from reliable websites that we have updated for users to get maximum savings. Take action now for maximum saving as these discount codes will not valid forever. You can always come back for Bobcat S650 Codes because we update all the latest coupons and special deals weekly. View more
Mar 01, 2021 · Financing and Cash Rebates on Bobcat Mini Track Loaders. P
Bobcat Miner 300 Promo Code. 30% off (2 days ago) Bobcat Miner 300 Promo Cod
Bobcat Error Codes | Bobcat Fault Codes
Get info about Bobcat construction vehicles error/fault codes. Bobcat Facts
Jun 18, 2020 · Throttle control open circuit replace throttle control sen
55% Off Bobcat Coupon Code | Verified May 2021
My bobcat 650s is showing codes mo514 and mo 515. 650 S Alj814461. Put in so
Apr 08, 2021 · THE BOBCAT STORE Coupon Codes 2021 go to bobcatstore. ohioa
Bobcat S650 Error Codes can offer you many choices to save money thanks to 1
8 active results. You can get the best discount of up to 57% off. The new discount codes are constantly updated on Couponxoo. The latest ones are on May 13, 2021
May 14, 2015 · RETAIL READY for IMMEDIATE PICKUP or DELIVERY! 2015 Bobcat
Bobcat fault codes list | Truckmanualshub. com
Jun 01, 2018 · Bobcat fault codes list (error codes) for most popular mod
el as Bobcat 873, Bobcat s130, Bobcat e85
Today I take a look at a customers Bobcat S650 for a Til fault code and an a
ir conditioning issue. From start to finish you see the process I took to diagnos.
Bobcat S650 Skid-Steer Loader. The S650 loader has a vertical lift path and
gives you greater lifting capacity and forward reach at full lift-height, for truck loading and pallet handling. Its wide attachments range also opens up many new applications where very high lift capacity, but with a compact-sized loader, are important.
Listed above you’ll find some of the best bobcat coupons, discounts and prom
otion codes as ranked by the users of RetailMeNot. com. To use a coupon simply click the coupon code then enter the code during the store’s checkout process. Today’s Top Bobcat Offers: Select …
S650 egr fault codes | Heavy Equipment Forums
Nov 10, 2018 · First cold day in MN and my S650 decided it was time to th
row some EGR fault codes and run at half power. Anyone else run into this with the doosan engines? Looked around for a bit tonight after parking it in the shop and I have no idea where the valve even is to check for soot plugging it.
Amazon. com: bobcat mirror
2019 bobcat s650, bobcat s650 rubber tire skidsteer loader, high flow, aux h
S650 bobcat My drive belt burn up i replace it no i have m7748 code which sh
uts the machine off and keeps the dash lights onits mulpuabe key swich code i replace the key swicht and bypass swicht it …
Depot Coupon can offer you many choices to save money thanks to 24 active results. You can get the best discount of up to 58% off. The new discount codes are constantly updated on Couponxoo. The latest ones are on May 01, 2021 12 new Bobcat Depot Coupon results have been found in the last 90 days, which means that every 8, a new Bobcat
Thermostat Assembly | 7332632 | Genuine Bobcat Parts
Electronic thermostatic sensor probe for heater and A/C. Fits the following
2016 bobcat s650 Wheel Clean Unit 74hp Tier 4 Bobcat Engine, 2650 Rated Op.
Capacity, Power Bobtach, Key Start, Attach Control Kit, Radio, Suspension Seat, New 12.00-16.5 Tires
2019 bobcat s650, bobcat s650 rubber tire skidsteer loader, high flow, aux h
Bobcat Skid Steers for Sale New & Used | Fastline
2017 Bobcat S650, Deluxe instrument panel, keyless start, 7 pin, 2 speed, he
H7404 Error Code For Bobcat S650 | BobcatErrorCode. com
Tip For S650 Model. This machine is factory equipped with a spark arrester e
xhaust system. The spark arrester muffler, if equipped, must be cleaned to keep it in working condition. The spark arrester muffler must be serviced by dumping the spark chamber every 100 hours of operation.
bobcat service manual, bobcat repair manual
Bobcat S650 Skid – Steer Loader Service Repair Manual (S/N 1MLS11001 & Abo
ve) Bobcat S650 Skid – Steer Loader Service Repair Manual (S/N ALJ811001 & Above, S/N S1ML11001 & Above, S/N B2LA11001 & Above) Bobcat S740 Skid – Steer Loader Service Repair Manual (S/N B3BT11001 & Above, S/N B3M311001 & Above)
Bobcat S650 Skid-Steer Loader Specs Price, Video & Images
Jan 25, 2021 · Bobcat S650 Price, Specs, Weight, Oil Capacity, Tire Size,
Oil capacity, Review, Engine features, Images. The Bobcat S650 Mini skid-steer loader is a vertical lift path model in the 600 frame size. It gives increased lifting capacity and offers greater forward reach at full lift height for loading trucks.
35% off Bobcat Lighting Coupons and Promo Codes 2021. 35% off Offer Details:
About Bobcat Lighting. Enjoy the latest 8 coupons and deals for bobcatlighting. com. These coupons are updated on 29, Mar 2021 by our MissedCoupon. com’s coupon submission communities, these bobcatlighting. com coupons, deals, offers and discount code has been verified on a timely manner to check the …
ader. 3116 FORT WORTH, TX. 2015 BOBCAT S650 Skid Steer Loader. 907 DENVER, CO. 2018 BOBCAT S650 Skid Steer Loader. 415 DENVER, CO. 2012 BOBCAT S650 2 spd Skid Steer Loader. 3432 DENVER, CO.
W3258 Error Code For Bobcat S650 | BobcatErrorCode. com
Tip For S650 Model. When operating on uneven ground, operate as slow as poss
ible and avoid sudden changes in direction. Avoid travelling over objects such as rocks, trees, stumps, etc. When working on wet or soft ground, put planks on the ground to provide a solid base to travel on and prevent the excavator from getting stuck.
M1307 Error Code For Bobcat S150 | BobcatErrorCode. com
View M1307 error code and check possible symptoms, causes and fixing ways fo
r M1307 fault code Bobcat S150 model.
BOBCAT S650 Auction Results. Sort by manufacturer, model, year, price, locat
ion, sale date, and more. Page 1 of 1.
Bobcat S650 Skid Steer Parts New Aftermarket, Used and Rebuilt S650 Parts. L
ooking for Bobcat S650 Skid Steer parts? You’ve come to the right place. We sell a wide range of new aftermarket, used and rebuilt S650 replacement parts to get your machine back up and running quickly.
tier 4 doosan engines in bobcat | Heavy Equipment Forums
Feb 27, 2015 · The local Bobcat salesman said that because they do not us
D3907 Error Code For Bobcat E42 | BobcatErrorCode. com
Tip For E42 Model. Stop the machine on a firm flat surface. When removing or
installing attachments (such as a bucket), always have a second person in the …
M0921 Error Code For Bobcat 430 | BobcatErrorCode. com
Tip For 430 Model. This machine is factory equipped with a spark arrester ex
haust system. The spark arrester muffler, if equipped, must be cleaned to keep it in working condition.
M3507 Error Code For Bobcat T190 | BobcatErrorCode. com
View M3507 error code meaning for Bobcat T190.
Bobcat fault codes The site tractor-manuals. jimdofree. com supports the autho
rs of the literature presented on the site in their desire to protect their copyright. If you are the copyright holder of a user manual, please contact us by mail and we will remove it from …
Bobcat S650 Skid Steer Engines New Aftermarket, Used and Rebuilt S650 Engine
s. Looking for Bobcat S650 Skid Steer Engines? You’ve come to the right place. We sell a wide range of new aftermarket, used and rebuilt S650 replacement engines to get your machine back up and running quickly.
EquipmentFacts. com | 2012 BOBCAT S650 Online Auctions
Apr 20, 2021 · Complete details for 2012 BOBCAT S650 auction listing avai
lable from EquipmentFacts. com, the online bidding platform.
E00279105 Error Code For Bobcat S750 | BobcatErrorCode. com
View E00279105 error code meaning for Bobcat S750.
Please Rate Here
? Average Discount: 5.6$
? Amount Of Coupons: 46
? Highest Discount: 58% off
Filter Search
Coupon Type
Other Good Coupons
What kind of cab does a bobcat S650 have?
2019 Bobcat S650, A-91 package, cab, heat, air, SJC, high flow, and radio. 2011 Kubota S650 Skid Steer Loader equipped with an enclosed Cab w/ Heat and AC. Features 2 speed and bucket. Available at our Anoka store.
Where can I get a 2015 Bobcat skid steer?
What kind of tires does a 2015 bobcat have?
What kind of financing does a bobcat get?
2018 Bobcat S650, BOBCAT S650, RUBBER TIRE SKIDSTEER LOADER, HIGH FLOW AUX HYDRAULICS, PILOT CONTROLS, TIER 4 FINAL, TURBO DIESEL FINANCING AVAILABLE. 2019 Bobcat S650, BOBCAT S650, RUBBER TIRE SKIDSTEER LOADER, HIGH FLOW, AUX HYDRAULICS, PILOT CONTROLS, TIER 4F TURBO DIESEL FINANCING AVAILABLE, BEST.
Top Stores
Tips Not To Miss Any Coupons 24/7
1. Email subscription
To receive coupons and discounts notification, sign up for email list of the retailer.
Check out Facebook, Twitter, Instagram page for upcoming sales and coupon promotions.
You have free access to different coupon sites like isCoupon to search for active discounts.
Full advantages of Amazon Discount Hunter.
The tool filters out the lowest price and the highest discounts available, making purchase decisions easier than ever.
2. Customized search
Type in search bar whatever product you look for and the tool will show you the best deals
Not much time wasted for the results. You are just a few clicks away from accurate options for your saving.
Popular Searched
Recently Searched
Don’t Miss Another Deals!
Subscribe to get notification about new coupon!
Latest Blog Posts
Hoverboards are trending and if you want to buy one, check these details first about buying and using a hoverboard.
How Smart Wearables Can Help You Boost the Soccer Game?
We are going to go through all the data on why these smart gadgets are becoming so popular.
Is the Tesla Roadster really the fastest car in the world? Here is everything you need to know about this hypercar.
What is Boba Tea (bubble tea)?
Enjoy the new and unique taste of Boba tea in your local area. Get the best deals for Boba or bubble tea.
How does Netflix Know Exactly What you want to see?
Netflix is an amazing platform and we love it but there is science involved in why we are so much addicted to its content.
Can Anyone Track My Phone’s Precise Location?
Different entities can track the location of your phone so beware of what you do on your smartphone.
How to find bobcat s650 codes?
Why do all online visitors like the coupon code? Because this is a useful way to save money when shopping online. However, searching for coupons online, but not sure where to look or who to trust? There are lots of coupon websites out there, but some are unreliable, hard to navigate and filled with useless coupons. Therefore, you can find coupon codes online in three ways: via search engines, using automated shopping tools, or direct from coupon code sites. Before searching coupons code, you need to identify the store to buy first, then filter and select the best coupons code.
What else we have?
Amazon Coupon Searcher
You don’t have to try all the coupons you found on others websites. With the Amazon Coupon Searcher tool, you can rely on these codes because we censored before it is publishing. Just 3 simple steps, you can find a reasonable discount code:
Step 1: Insert your country you want to buy as well as enter the product’s name at the bar tool.
Step 2: Select the department that is suitable for your search, and enter the minimum and maximum price of your products.
Step 3: You can choose »free shipping» for your orders.
When you press a »search discount», the tool will filter and give you results that best match the price and product you choose. Our Amazon Coupon Searcher is available in 12 countries like the United States, the United Kingdom, Japan, India.. and in the future, we will develop it in more countries in the world.
Источники:
https://snabavto. com/post/bez-rubriki/osobennosti-obsluzhivaniya-i-ekspluatacii-texniki-bobcat/
https://iscoupon. com/bobcat-s650-codes
Bobcat trouble codes
Error codes of mini loaders Bobcat will help you identify the faulty actuator and quickly repair the failed mechanism of both the engine and the hydraulic system.
Fault code | Description |
01-16 | Air filter not connected |
01-17 | Air filter clogged |
02-16 | Hydraulic pressure filter not connected. |
02-17 | Hydraulic pressure filter clogged |
03-09 | Low battery voltage |
03-10 | High battery voltage |
03-11 | Extremely high battery voltage |
03-14 | Extremely low battery voltage |
03-22 | The battery voltage is below the maximum allowable |
04-09 | Low engine oil pressure |
04-14 | Extremely low engine oil pressure |
04-15 | Oil pressure in the engine at the level of emergency engine shutdown |
04-21 | Engine oil pressure above maximum permissible |
04-22 | Engine oil pressure below the maximum allowable |
05-09 | Low recharge pressure in hydraulic system |
05-14 | Extremely low make-up pressure in the hydraulic system |
05-15 | Feed pressure in the hydraulic system at the level of emergency engine shutdown |
05-21 | Feed pressure in the hydraulic system is higher than the maximum allowable |
05-22 | Feed pressure in the hydraulic system is below the maximum allowable |
06-10 | High engine speed |
06-11 | Extremely high engine rpm |
06-13 | No engine speed signal |
06-15 | Engine speed at the level of emergency engine shutdown |
06-18 | Engine speed outside permissible limits |
07-10 | High hydraulic oil temperature |
07-11 | Extremely high hydraulic oil temperature |
07-15 | Oil temperature in the hydraulic system at the level of emergency engine shutdown |
07-21 | Oil temperature in the hydraulic system is higher than the maximum allowable |
07-22 | Oil temperature in the hydraulic system below the maximum allowable |
08-10 | High engine coolant temperature |
08-11 | Extremely high engine coolant temperature |
08-15 | Engine coolant temperature at the level of emergency engine shutdown |
08-21 | Engine coolant temperature is above the maximum allowable |
08-22 | Engine coolant temperature below the maximum allowable |
09-09 | Low fuel level |
09-21 | Fuel level above the maximum allowable |
09-22 | The fuel level is below the maximum allowable |
11-05 | Safety frame sensor shorted to battery |
11-06 | Safety frame sensor shorted to ground |
12-21 | Signal PWM controller front ext. hydraulics beyond the upper limit of the range |
12-22 | PWM controller front ext. hydraulics beyond the low end of the range |
12-23 | PWM controller front ext. non-neutral hydraulics |
13-05 | Fuel shut-off holding solenoid shorted to battery |
13-06 | Holding solenoid fuel cutoff shorted to ground |
13-07 | Open circuit of fuel cut-off solenoid |
14-02 | Fuel cut-off solenoid, erroneous switch on |
14-03 | Fuel shut-off solenoid, erroneous shutdown |
15-02 | Retractable solenoid locking thrust, erroneous inclusion |
15-03 | Retractable solenoid locking thrust, erroneous shutdown |
16-05 | Holding solenoid lockout closed on battery |
16-06 | Holding solenoid blocking thrust closed to ground |
16-07 | Open circuit retaining solenoid blocking traction |
17-05 | Solenoid hydraulic shut-off valve shorted to battery |
17-06 | Solenoid hydraulic shut-off valve shorted to ground |
17-07 | Open circuit of the solenoid hydraulic shut-off valve |
18-05 | The solenoid of the valve is closed to the battery |
18-06 | Solenoid spool closed to ground |
18-07 | Open circuit of the spool solenoid |
19-02 | Bucket positioning solenoid, erroneous switch on |
19-03 | Solenoid bucket positioning, erroneous shutdown |
20-02 | Solenoid switching speeds erroneous inclusion |
20-03 | Solenoid switching speeds erroneous shutdown |
21-02 | Glow plugs, erroneous inclusion |
21-03 | Glow plugs, erroneous shutdown |
22-02 | Starter, erroneous inclusion |
22-03 | Starter, mistaken shutdown |
23-02 | Rear Base Solenoid, Incorrect Inclusion |
23-03 | Rear base solenoid, faulty shutdown |
24-02 | Rear stock solenoid, erroneous switch on |
24-03 | Rear stock solenoid, erroneous shutdown |
25-02 | Rear Auxiliary Proportional Solenoid, Incorrect Inclusion |
25-03 | Rear auxiliary proportional solenoid, erroneous shutdown |
26-02 | Incorrect inclusion of the front base solenoid |
26-03 | Wrong shutdown of the front base solenoid |
27-02 | Incorrect inclusion of the front stock solenoid |
27-03 | Wrong shutdown of the front stock solenoid |
28-02 | Incorrect inclusion of diverter solenoid |
28-03 | Erroneous diverter solenoid shutdown |
29-02 | Large feed solenoid, erroneous switch on |
29-03 | Large feed solenoid, faulty shutdown |
30-28 | Controller memory failure |
31-28 | Recovery Mode Malfunction |
32-04 | Extended Control (ACS) does not communicate with the Bobcat controller |
32-23 | Extended ACS Management Not Calibrated |
32-31 | Tilt actuator failure |
32-32 | Malfunctioning wiring of the tilt actuator |
32-33 | Faulty wiring tilt bucket handle |
32-34 | Tilt actuator not in neutral |
32-35 | Bucket tilt lever / pedal not in neutral position |
32-36 | Lift actuator failure |
32-37 | Faulty wiring actuator lifting |
32-38 | Faulty wiring of boom lift handle |
32-39 | Actuator not in neutral |
32-40 | Arm / boom pedal not in neutral position |
32-41 | No connection |
32-49 | Lifting actuator shorted to ground |
32-50 | Tilt actuator shorted to ground |
32-51 | Lifting actuator shorted to battery |
32-52 | Tilt actuator shorted to battery |
32-53 | Arm / Boom Lift Pedal Closed to Ground |
32-54 | The handle / pedal tilt bucket closed to ground |
32-55 | Arm / Boom Lift Pedal Closed to Battery |
32-56 | The handle / pedal tilt bucket closed on the battery |
32-57 | Reduced lift actuator performance |
32-58 | Reduced tilt actuator performance |
32-59 | Wrong direction of the lifting actuator |
32-60 | Incorrect direction of tilt actuator |
32-61 | Handle lock closed to ground |
32-62 | Handle lock closed on battery |
32-63 | The pedal lock circuit is shorted to ground |
32-64 | The pedal lock circuit is closed to battery |
32-65 | Sensor supply voltage outside permissible limits |
32-66 | Battery voltage out of range |
32-67 | Switch switched during operation |
32-68 | Information error arm lifting boom |
32-69 | Control switch switched during operation |
32-70 | The chain of the right-hand grip is closed to ground |
32-71 | The chain of the right grip movement is closed on the battery |
33-23 | Main controller ( Bobcat controller ) not programmed |
34-04 | The pushbutton panel does not communicate with the Bobcat controller |
35-02 | Two-speed fan switch, erroneous on |
35-03 | Two-speed fan switch, erroneous shutdown |
36-48 | Multiple ACD controllers connected |
37-02 | Two-speed additional speed selector, erroneous start |
37-03 | Two-speed optional speed switch, erroneous shutdown |
38-04 | No connection to joystick controller |
38-05 | X axis of the left joystick is not in neutral position |
38-06 | X axis of the right joystick is not in neutral |
38-07 | Y axis of the left joystick is not in neutral position |
38-08 | Y axis of the right joystick is not in neutral |
38-09 | Control mode switch – short to battery or ground |
38-11 | Actuator not in neutral |
38-12 | Tilt actuator not in neutral |
38-13 | Lift actuator failure |
38-14 | Tilt actuator failure |
38-15 | Faulty wheel speed control wiring |
38-16 | Fault wiring for left wheel speed |
38-17 | Reduced tilt actuator performance |
38-18 | Reduced lift actuator performance |
38-19 | X axis of the left joystick, beyond the upper limit of the range |
38-20 | X axis of the right joystick, beyond the lower limit of the range |
38-21 | Y axis of the left joystick, beyond the upper limit of the range |
38-22 | Y axis of the right joystick, beyond the upper limit of the range |
38-23 | The signal of the front right sensor control for the upper limit of the range |
38-24 | The signal of the front left sensor control for the upper limit of the range |
38-25 | The signal of the rear right control sensor beyond the upper limit of the range |
38-26 | The signal of the rear left sensor control for the upper limit of the range |
38-27 | Lift actuator signal over upper range limit |
38-28 | Tilt actuator signal above upper range limit |
38-29 | X axis of the left joystick, beyond the lower limit of the range |
38-30 | X axis of the right joystick, beyond the lower limit of the range |
38-31 | Y axis of the left joystick, beyond the lower limit of the range |
38-32 | Y axis of the right joystick, beyond the lower limit of the range |
38-33 | The signal of the front right control sensor for the lower limit of the range |
38-34 | The signal of the front left control sensor for the lower limit of the range |
38-35 | The signal of the rear right control sensor for the lower limit of the range |
38-36 | The signal of the rear left control sensor for the lower limit of the range |
38-37 | Power supply “1” 5-volt sensor, beyond the lower limit of the range |
38-38 | Power supply “2” 5-volt sensor, beyond the lower limit of the range |
38-39 | Actuator lifting closed to ground / beyond the lower limit of the range |
38-40 | Tilt actuator shorted to ground / signal beyond low range |
38-41 | Incorrect direction of tilt actuator |
38-42 | Wrong direction of the lifting actuator |
38-43 | Solenoid left front drive, erroneous inclusion |
38-44 | Solenoid of the left reversive drive, wrong inclusion |
38-45 | Solenoid of the right front drive, erroneous inclusion |
38-46 | Solenoid of the right reverse drive, erroneous inclusion |
38-47 | Front right control solenoid, erroneous switch on |
38-48 | Front left control solenoid, erroneous switch on |
38-49 | Rear right control solenoid, erroneous switch on |
38-50 | Rear left control solenoid, erroneous switch on |
38-51 | Control pressure solenoid, erroneous switch on |
38-52 | Reverse signal, erroneous activation |
38-53 | Solenoid left front drive, erroneous shutdown |
38-54 | Solenoid of the left reversive drive, wrong shutdown |
38-55 | Solenoid right front drive, erroneous shutdown |
38-56 | Solenoid of the right reversive drive, wrong shutdown |
38-57 | Front right solenoid advance control, erroneous shutdown |
38-58 | Front right solenoid control retract, erroneous shutdown |
38-59 | Front left extension control solenoid, faulty shutdown |
38-60 | Front left solenoid control retract, erroneous shutdown |
38-61 | Rear right firing solenoid, erroneous shutdown |
38-62 | Rear right solenoid control retract, erroneous shutdown |
38-63 | Rear left advance control solenoid, faulty shutdown |
38-64 | Rear left solenoid control retract, erroneous shutdown |
38-65 | Solenoid pressure control system, erroneous shutdown |
38-66 | Reverse signal, erroneous shutdown |
38-67 | No messages from Bobcat controller |
38-68 | Wheel alignment angles (alignment) not calibrated |
38-69 | Lifting and tilting actuators not calibrated |
38-70 | Power down |
38-71 | Battery voltage out of range |
38-72 | Drive Pump Not Calibrated |
38-73 | Control mode / motion mode switch switched during operation |
38-74 | Unmanaged right wheel speed |
38-75 | Unmanaged left wheel speed |
38-76 | Solenoid pressure control system – insufficient current |
38-77 | Front Right Solenoid Extend Control – Insufficient Current |
38-78 | Front Right Solenoid Control – Low Current |
38-79 | Front Left Extend Control Solenoid – Insufficient Current |
38-80 | Front Left Solenoid Control Retractor – Insufficient Current |
38-81 | Rear Right Solenoid Extend Control – Insufficient Current |
38-82 | Rear right solenoid inlet control – insufficient current |
38-83 | Rear Left Extension Control Solenoid – Insufficient Current |
38-84 | Rear Left Solenoid Control Retractor – Insufficient Current |
38-85 | Power supply “1” 5-volt sensor beyond the upper limit of the range |
38-86 | Power supply “2” 5-volt sensor beyond the upper limit of the range |
38-87 | Lock the right front wheel (mechanical control failure) |
38-88 | Lock the left front wheel (mechanical control failure) |
38-89 | Lock the right rear wheel (mechanical control failure) |
38-90 | Rear left control error |
38-91 | No wheel speed sensor pulses |
38-92 | No left wheel speed sensor pulses |
38-93 | Right wheel speed sensor not responding |
38-94 | Left wheel speed sensor not responding |
38-98 | Controller in drive calibration mode |
38-99 | Controller in wheel position calibration mode |
45-03 | Right direction indicator, wrong shutdown |
46-02 | Left turn signal, erroneous inclusion |
46-03 | Left direction indicator, erroneous shutdown |
47-21 | Power supply 8-volt sensor beyond the upper limit of the range |
47-22 | Power supply 8-volt sensor, beyond the lower limit of the range |
48-02 | Front light relay erroneous on |
48-03 | Front light relay erroneous shutdown |
49-02 | Reverse light switch |
49-03 | Relay backlight, erroneous shutdown |
60-21 | Signal control lever rear ext. hydraulics beyond the upper limit of the range |
60-22 | Signal control lever rear ext. hydraulics beyond the lower limit of the range |
60-23 | Control lever rear ext. hydraulically does not return to neutral |
64-02 | Incorrect power switch on |
64-03 | Faulty power down |
74-72 | Bobcat controller boot code failure |
74-73 | Left panel, receiver error |
80-02 | ACD, output “A”, wrong inclusion |
80-03 | ACD, output “A”, wrong shutdown |
81-02 | ACD, output “B”, wrong switch |
81-03 | ACD, output “B”, wrong shutdown |
82-02 | ACD, output “C”, wrong inclusion |
82-03 | ACD, output “C”, wrong shutdown |
83-02 | ACD, output “D”, wrong switch |
83-03 | ACD, output “D”, wrong shutdown |
84-02 | ACD, output “E”, wrong switch |
84-03 | ACD, output “E”, wrong shutdown |
90-02 | Service output “C”, erroneous activation |
90-03 | Service output “C”, erroneous shutdown |
91-02 | Service output “D”, erroneous activation |
91-03 | Service output “D”, erroneous shutdown |
92-02 | Service exit “E”, erroneous inclusion |
92-03 | Service output “E”, erroneous shutdown |
93-02 | Service output “F”, erroneous start |
93-03 | Service output “F”, erroneous shutdown |
Press the information button (item 1) to scroll the screen (item 2) until the engine hours menu is displayed.
Press and hold the info button (item 1) for three seconds until the
service codes will not appear on the screen.
If several service codes are present, they will be displayed one after the other on the display.
NOTE. Corroded or loose ground connections can cause multiple service codes and / or abnormal symptoms. Blinking of all dashboard indicators, sounding of an alarm, blinking of head and rear
lights can indicate poor grounding. The same symptoms can occur with low voltage (for example, due to loose or corroded battery wires). If these symptoms appear, first check the ground and
positive terminals.
Service codes can be a word (item 3) or a number (item 4).
The following error messages may be displayed:
[NONE] — no service codes.
[REPLY] — The dashboard is not communicating with the controller.
[SHTDN] (Off) — Disabled state.
Press and hold the info button (item 1) for three seconds to return to the engine hours menu.
Service Code List — Engine Controller
CODE DESCRIPTION RESULTS
E000100-03 Oil pressure sensor error; signal above control range
E000100-04 Oil pressure sensor error; signal below control range
E000102-02 The charge air pressure is above the threshold level for warning
E000102-02 The charge air pressure is above the threshold level for shutdown
E000102-03 Charge air pressure sensor error; signal above control range
E000102-04 Charge air pressure sensor error; signal below control range
E000105-00 High charge air cooler temperature; value above the warning threshold
E000105-00 High charge air cooler temperature; value above the threshold for shutdown
E000105-03 Discharge air temperature sensor error; signal above control range
E000105-04 Discharge air temperature sensor error; signal below control range
E000110-00 Coolant temperature too high; value above the warning threshold (111 ° C)
E000110-00 Coolant temperature too high; value above the switch-off threshold (119 ° C)
E000110-03 Coolant temperature sensor error; signal above control range
E000110-04 Coolant temperature sensor error; signal below control range
E000157-03 Line pressure sensor error; signal above control range
E000157-04 Line pressure sensor error; signal below control range
E000164-02 Line pressure protection function is not performed properly
E000168-00 Physical test detected too high battery voltage
E000168-01 Physical test detected too low battery voltage
E000168-02 High battery voltage; value above the warning threshold
E000168-02 Low battery voltage; value above the warning threshold
E000168-03 Battery voltage sensor error; signal above control range
E000168-04 Battery voltage sensor error; signal below control range
E000190-00 Engine speed above threshold level for warning (FOC level 1)
E000190-02 Too large angle between the crankshaft and camshaft sensors
E000190-08 Camshaft speed sensor; unstable signal
E000190-08 Crankshaft speed sensor; unstable signal
E000190-011 Motor speed above threshold level for warning (FOC level 2)
E000190-012 Camshaft speed sensor; no signal
E000190-012 Crankshaft speed sensor; no signal
E000190-014 Engine speed above warning threshold (overspeed mode)
E000190-014 The signal from the crankshaft and camshaft speed sensor is not available on the CAN bus
E000520-09 Timeout error for receiving frame on the CAN bus TSC1TR; set value
E000630-012 EEPROM memory access error (delete)
E000630-012 EEPROM memory access error (read)
E000630-012 EEPROM memory access error (write)
E000639-014 CAN bus 0 (state — bus off)
E000651-03 Injector 1 (in ignition order); short circuit
E000651-04 Short circuit from high voltage side to low voltage side in injector 1 (in ignition order)
E000651-05 Injector 1 (in ignition order); broken electrical connection
E000652-03 Injector 2 (in ignition order); short circuit
E000652-04 Short circuit from high voltage side to low voltage side in injector 2 (in ignition order)
E000652-05 Injector 2 (in ignition order); broken electrical connection
E000653-03 Injector 3 (in ignition order); short circuit
E000653-04 Short circuit from the high voltage side to the low voltage side in injector 3 (in the order of ignition)
E000653-05 Injector 3 (in ignition order); broken electrical connection
E000654-03 Injector 4 (in ignition order); short circuit
E000654-04 Short circuit from high voltage side to low voltage side in injector 4 (in ignition order)
E000654-05 Injector 4 (in ignition order); broken electrical connection
E000676-011 Cold start auxiliary relay error.
E000676-011 Load of opening auxiliary cold start relay
E000677-03 High voltage side of starter relay; short circuit to battery
E000677-03 Low voltage side of starter relay; short circuit to battery
E000677-04 High voltage side of starter relay; short circuit to ground
E000677-04 Low voltage side of starter relay; short circuit to ground
E000677-05 Starter relay; error — no load
E000677-012 Starter relay; high temperature in the feeding phase
E000729-05 Opening load of auxiliary cold start relay
E000729-012 Auxiliary cold start relay; error — excessive temperature
E000898-09 TSC1TE CAN bus frame receive timeout error; set value
E001079-013 Sensor 1 supply voltage monitor error (ECU)
E001080-013 Sensor 2 supply voltage monitor error (ECU)
E001109-02 Request to turn off the engine is ignored
E001136-00 Physical test detected too high ECU temperature
E001136-01 Physical test detected too low ECU temperature
E001136-03 ECU temperature sensor error; signal above control range
E001136-04 ECU temperature sensor error; signal below control range
E001231-014 CAN bus 1 (state — bus off)
E001235-014 CAN bus 2 (state — bus off)
E001322-012 Too many misfire detected in multiple cylinders
E001323-012 Too many cylinder 1 misfire detected (in ignition order)
E001324-012 Too many misfire detected in cylinder 2 (in ignition order)
E001325-012 Too many cylinder 3 misfire detected (in ignition order)
E001326-012 Too many cylinder 4 misfire detected (in ignition order)
E002797-04 Diagnosis of the injector; earth fault measurement timeout error — cylinder group 0
E002798-04 Injector diagnostics; earth fault measurement timeout error — cylinder group 1
E002798-04 Injector diagnostics; earth fault monitoring — check cylinder bank 0
E002798-04 Injector diagnostics; earth fault monitoring — check cylinder bank 1
E523008-01 Manipulation control was initiated
E523008-02 Keying control timeout error
E523009-09 The maximum permissible number of openings of the pressure relief valve has been reached
E523009-010 The maximum permissible opening time of the pressure relief valve has been reached.
E523212-09 CAN frame receive timeout error ComEngPrt; motor protection
E523216-09 CAN bus frame receive timeout error PrHtEnCmd; preheat command, motor command
E523240-09 CAN bus timeout message FunModCtl; operating mode control
E523330-014 Immobilizer status; fuel filter clogged
E523350-04 Injector, cylinder group 1; short circuit
E523352-04 Injector, cylinder group 2; short circuit
E523354-012 Injector output defect on the supply phase
E523470-02 Pressure relief valve forced opening (PRV); performed under pressure conditions
E523470-02 Pressure relief valve forced opening (PRV); performed under shockwave conditions
E523470-07 Maximum line pressure exceeded in emergency mode (PRV)
E523470-011 PRV cannot be opened at this stage of the operating procedure under shockwave conditions
E523470-011 Line pressure out of range
E523470-012 Opening of the pressure relief valve (PRV); shutdown state
E523470-012 Pressure relief valve (PRV) opening; warning state
E523470-014 Pressure relief valve (PRV) open
E523550-012 Start switch T50 active for too long
E523601-013 Sensor 3 supply voltage monitor error (ECU)
E523605-09 TSC1AE CAN bus frame receive timeout error; traction control
E523606-09 CAN frame receive timeout error TSC1AR; deceleration mechanism
E523612-012 Firmware error (ECU); injection closure
E523612-012 Detection error during internal monitoring of the ECU
E523612-012 Detection error during internal monitoring of the ECU
E523612-012 Detection error during internal monitoring of the ECU
E523612-012 Detection error during internal monitoring of the ECU
E523612-012 Detection error during internal monitoring of the ECU
E523612-012 Detection error during internal monitoring of the ECU
E523612-012 Detection error during internal monitoring of the ECU
E523612-012 Detection error during internal monitoring of the ECU
E523612-012 Detection error during internal monitoring of the ECU
E523612-012 Detection error during internal monitoring of the ECU
E523612-012 Detection error during internal monitoring of the ECU
E523612-012 Detection error during internal monitoring of the ECU
E523612-012 Detection error during internal monitoring of the ECU
E523612-012 Detection error during internal monitoring of the ECU
E523612-012 Detection error during internal monitoring of the ECU
E523612-012 Detection error during internal monitoring of the ECU
E523612-012 Firmware error (ECU)
E523612-014 CPU software reset (CPU SWReset_0)
E523612-014 CPU software reset (CPU SWReset_1)
E523612-014 CPU software reset (CPU SWReset_2)
E523613-00 Maximum positive deviation of pressure in the line exceeded (RailMeUn0)
E523613-00 Maximum positive pressure deviation in the metering device line (RailMeUn1) exceeded
E523613-00 Line system leak detected (RailMeUn10)
E523613-00 Maximum negative pressure deviation in the metering device line (RailMeUn2) exceeded
E523613-00 Negative deviation of line pressure in the second phase (RailMeUn22)
E523613-00 Maximum rail pressure exceeded (RailMeUn4)
E523613-01 Minimum rail pressure exceeded (RailMeUn3)
E523613-02 Dosing device setpoint in overspeed mode is invalid
E523615-03 Metering device (fuel system); short circuit on the high voltage side of the battery
E523615-03 Metering device (fuel system); short circuit on the low voltage side of the battery
E523615-04 Metering device (fuel system); short to ground (high voltage side)
E523615-04 Metering device (fuel system); short to ground (low voltage side)
E523615-05 Metering device (fuel system); opening load
E523615-012 Metering device (fuel system); high temperature in the feeding phase
E523698-011 Switch-off request from the control monitoring function
E523717-012 AmbCon CAN frame transmission timeout error; weather
E523766-09 TSC1AE bus frame receive timeout error; actively
E523767-09 CAN frame receive timeout error TSC1AE; passively
E523768-09 CAN frame receive timeout error TSC1AR; actively
E523769-09 CAN frame receive timeout error TSC1AR; passively
E523770-09 TSC1DE CAN bus frame receive timeout error; passively
E523776-09 TSC1TE CAN bus frame receive timeout error; actively
E523777-09 CAN frame receive timeout error TSC1TE — passive; set value
E523778-09 CAN frame receive timeout error TSC1TR — active
E523779-09 TSC1TR bus frame receive timeout error — passive
E523895-013 Checking the absence of a programmable setting value for injector 1 (in the order of ignition)
E523896-013 Checking the absence of a programmable setting value for the injector 2 (in the order of ignition)
E523897-013 Checking the absence of a programmable setting value for injector 3 (in the order of ignition)
E523898-013 Checking the absence of a programmable setting value for injector 4 (in the order of ignition)
E523913-03 Sensor error — voltage in the glow plug diagnostic line; signal above control range
E523913-04 Sensor error — voltage in the glow plug diagnostic line; signal below control range
E523914-03 Glow plug control; short circuit to battery
E523914-04 Glow plug control; short circuit to ground
E523914-05 Glow plug control; opening load
E523914-05 Glow plug control reset line; error — short circuit
E523914-011 Glow plug control; Internal error
E523914-012 Glow plug control; high temperature in the feeding phase
E523929-00 Fuel balance control integrator injector 1 (in ignition order); maximum value exceeded
E523929-01 Fuel balance control integrator injector 1 (in ignition order); minimum value exceeded
E523930-00 Fuel balance control integrator injector 2 (in ignition order); maximum value exceeded
E523930-01 Fuel balance control integrator injector 2 (in ignition order); minimum value exceeded
E523931-00 Fuel balance control integrator injector 3 (in ignition order); maximum value exceeded
E523931-01 Fuel balance control integrator injector 3 (in ignition order); minimum value exceeded
E523932-00 Fuel balance control integrator nozzle 4 (in ignition order); maximum value exceeded
E523932-01 Fuel balance control integrator injector 4 (in ignition order); minimum value exceeded
E523935-012 CAN frame transmission timeout error EEC3VOL1; sent engine messages
E523936-012 CAN frame transmission timeout error EEC3VOL2; sent engine messages
E523946-00 Zero calibration fuel injector 1 (in ignition order); maximum value exceeded
E523946-01 Zero calibration fuel injector 1 (in ignition order); minimum value exceeded
E523947-00 Zero calibration fuel injector 2 (in ignition order); maximum value exceeded
E523947-01 Zero calibration fuel injector 2 (in ignition order); minimum value exceeded
E523948-00 Zero calibration fuel injector 3 (in ignition order); maximum value exceeded
E523948-01 Zero calibration fuel injector 3 (in ignition order); minimum value exceeded
E523949-00 Zero calibration fuel injector 4 (in ignition order); maximum value exceeded
E523949-01 Zero calibration fuel injector 4 (in ignition order); minimum value exceeded
E523982-00 Power phase diagnostics disabled; high battery voltage
E523982-01 Power phase diagnostics disabled; low battery voltage
E524035-012 Injector diagnostics; SPI communication timeout error
E524036-012 Diagnostics of the auxiliary injector; SPI communication timeout error
E524057-02 Electric fuel pump; fuel pressure build-up error
E524118-09 ComRxCM1 CAN frame receive timeout error
Service Code List — Gateway Controller
The gateway controller is located in the cockpit behind the right instrument panel and display panel.
M0309 Low battery voltage All functions enabled
M0310 Battery voltage high All functions enabled
M0311 Battery voltage extremely high All functions enabled
M0314 Battery voltage extremely low All functions enabled
M0322 Battery voltage below maximum permissible All functions are enabled
M0414 Engine oil pressure extremely low All functions enabled
M0415 Engine oil pressure at emergency shutdown level Engine shutdown
M0610 High engine speed All functions enabled
M0611 Extremely high engine speed All functions enabled
M0613 No engine speed signal Movement disabled
M0615 Engine speed at emergency shutdown level Engine shutdown
M0618 Engine speed out of range All functions enabled
M0710 High hydraulic oil temperature All functions enabled
M0711 Extremely high oil temperature in the hydraulic system.
M0715 Oil temperature in the hydraulic system at the emergency engine shutdown level.
M0810 Engine coolant temperature high All functions enabled
M0811 Engine Coolant Temperature Extremely High All functions enabled
M0815 Engine coolant temperature at emergency shutdown level Engine shutdown
M0821 Engine coolant temperature above maximum limit All functions enabled
M0822 Engine coolant temperature below minimum limit All functions enabled
M0909 Low fuel level All functions enabled
M0921 Fuel level above maximum limit All functions enabled
M0922 Fuel level below minimum limit All functions enabled
M1602 Front alignment indicator output, faulty activation All functions are enabled
M1603 Front alignment indicator output, erroneous shutdown All functions enabled
M1702 Rear alignment indicator output, faulty activation All functions enabled
M1703 Rear alignment indicator output, erroneous shutdown All functions enabled
M1821 Frame alignment potentiometer signal above limit frame alignment locked
M1822 Frame alignment potentiometer signal below limit frame alignment locked
M2405 Side control valve output, short to battery Movement reduced
M2406 Side control valve output, earth fault All functions enabled except side control
M2407 Side control valve output, open circuit All functions enabled except side control
M2505 Valve 4 wheels, short circuit to battery Movement reduced
M2506 4 wheel valve, ground fault 4 wheel steering not available
M2507 Valve 4 wheels, open circuit 4-wheel steering mode not available
M2648 Steering mode switch, multiple active inputs All functions enabled
M2702 Fan inverter output, erroneous power-up Fan inverter enabled
M2703 Fan inverter output, erroneous shutdown Fan inverter not available
M2707 Fan inverter output open circuit Fan inverter not available
M2805 Fan PWM output, short to battery Fan inverter not available
M2806 Fan PWM output, ground fault Fan inverter not available
M2807 Fan PWM output open circuit Fan inverter not available
M2832 Fan PWM output, overcurrent Fan inverter not available
M3128 Fault recovery mode Engine shutdown
M3204 No communication with workgroup controller Workgroup functions are disabled
M3404 No communication with display controller Information not displayed
M3604 No communication with engine controller Error — engine speed Movement disabled
Engine shutdown in case of Engine Controller failure
M3704 No signal from drive controller Travel and auxiliary hydraulic functions are disabled
M4109 Generator voltage low All functions enabled
M4110 Generator voltage high All functions enabled
M4304 No communication with the KSS keypad Manual cranking of the engine is prohibited (if previously blocked)
M4621 Encoder power supply outside upper range limit Influence on creep function
M4622 Encoder power supply below range limit Influence on creep function
M4805 Working light output, erroneous switching on Working light permanently on
M4806 Work light output, erroneous switch-off Work light not available
M5205 Electronic battery disconnect output, open circuit or short to battery
Open circuit: no power supplied If there is a short to battery (BSC): the electronic battery disconnect is always closed. All functions are enabled, but can remain closed when the key is in the
OFF position.
M5206 Electronic battery cut-off output, ground fault No power supplied to machine
M5207 Electronic battery cut-off output, open circuit Power is not supplied to machine
M5302 Electronic battery cut-off, sticking Machine always receives power even though the key is in the OFF position.
M5303 Electronic battery cut-off, opening error (sticking) Power is not supplied to machine
M6105 Safety valve, short to battery Run group functions disabled
M6106 Safety valve, earth fault Run group functions disabled
M6107 Safety valve, open circuit Working group functions disabled
M6131 Safety valve, overcurrent Run group functions disabled
M7748 Multiple keys active (service tool and key) Do not turn engine over
M9999 Incorrect table with permanent data Gateway functions disabled Unable to crank the engine
Service Code List — Drive Controller
The drive controller is located between the boom and cab, next to the front frame fuse box.
CODE DESCRIPTION RESULTS
D0217 Clogged hydraulic filter All functions enabled
D0321 Battery voltage above maximum limit All functions are disabled
D0322 Low battery voltage below the minimum limit All functions are disabled
D0421 Slow pedal signal above the maximum limit Movement is reduced to 20%
D0422 Slow pedal signal below the minimum limit Movement is reduced to 20%
D0428 Slow pedal input error Movement is reduced to 30%
D1402 Brake light output, erroneous activation All functions are enabled
D1403 Brake light output, erroneous shutdown All functions are enabled
D1407 Brake light output, open circuit All functions enabled
D1433 Brake light output, internal fault All functions enabled
D1502 Brake light relay, erroneous activation All functions are enabled
D1503 Brake light relay, erroneous shutdown All functions are enabled
D1605 Forward drive pump coil, short to battery Movement disabled
D1606 Forward drive pump coil, short to ground Forward travel disabled
D1607 Forward drive pump coil, open circuit Forward travel disabled
D1632 Forward drive pump coil, overcurrent Movement disabled
D1705 Reverse drive pump coil, short to battery Movement disabled
D1706 Reverse drive pump coil, short to ground Reverse disabled
D1707 Reverse drive pump coil, open circuit Reverse disabled
D1732 Reverse drive pump coil, overcurrent Movement disabled
D2002 Low speed output (hydraulic motor), erroneous inclusion Movement is reduced to 30%
D2003 Low speed output (hydraulic motor) erroneous shutdown Movement is reduced to 30%
D2007 Low speed output (hydraulic motor) open circuit Movement is reduced to 30%
D2033 Low speed output (hydraulic motor), internal controller failure Movement is reduced to 30%
D2102 Slow speed relay, erroneous activation Movement is reduced to 30%
D2103 Slow speed relay, erroneous shutdown Movement is reduced to 30%
D2202 Cancel valve output (hydraulic motor), erroneous activation All functions are enabled
D2203 Cancel valve output (hydraulic motor), erroneous shutdown All functions enabled
D2207 Cancel valve output (hydraulic motor) open circuit All functions enabled
D2233 Override valve output controller, internal fault All functions enabled
D2302 Cancellation valve relay, erroneous activation All functions are enabled
D2303 Cancellation valve relay, erroneous shutdown All functions are enabled
D2502 Left stabilizer on the floor, erroneous activation All functions are enabled
D2503 Left stabilizer on the floor, erroneous shutdown All functions are enabled
D2609 Low pressure in the hydraulic steering wheel All functions are enabled
D2621 The pressure in the hydraulic steering wheel is below the maximum permissible All functions are enabled
D2702 Right stabilizer on the floor, erroneous inclusion All functions are enabled
D2703 Right stabilizer on the floor, erroneous shutdown All functions are enabled
D2821 Left stabilizer pressure sensor signal out of range All functions enabled
D2822 Left stabilizer pressure sensor signal out of range All functions enabled
D2921 Right stabilizer pressure sensor signal out of range All functions enabled
D2922 Right stabilizer pressure sensor signal out of range All functions enabled
D3204 No communication with the workgroup controller Auxiliary hydraulics disabled
D3304 No communication with the gateway controller All functions are disabled
D3404 No communication with the display controller All functions are disabled
D3604 No communication with the engine controller Movement disabled
D3723 Incorrect program or permanent data Movement disabled
D3728 Controller failure Movement disabled
D3796 Power off All functions enabled
D3797 Programmed by the controller All functions are enabled
D4004 No communication with joystick Movement prohibited / boom movement prohibited
D4011 Right joystick roller is not in neutral (auxiliary hydraulics) Auxiliary hydraulics disabled
D4028 Joystick handle failure Movement prohibited / boom movement prohibited
D4113 Lever FNR, no signal Movement disabled
D4128 FNR, multiple active inputs Movement disabled
D4621 5V voltage sensor output above maximum limit All functions are disabled, engine shutdown
D4622 5V voltage sensor output below minimum limit All functions are disabled, engine shutdown
D5521 Tilt plate sensor 1 signal above maximum limit Movement reduced
D5522 Tilt plate sensor 1 signal below minimum limit Movement reduced
D5621 Tilt plate sensor 2 signal above maximum limit Movement reduced
D5622 Tilt plate sensor 2 signal below minimum limit Movement reduced
D5715 Stop tilt plate Engine shutdown
D5744 Swashplate Double Failure Movement Reduced
D5745 Divergence of the tilt plate Movement is reduced
D5746 Tilt plate not responding Movement disabled
D5824 Safe start plate not in neutral Movement disabled
D5835 Emergency drain and safe start valve stuck on position Movement disabled
D5911 Overspeed error Movement reduced
D5915 Overspeed shutdown Engine shutdown
D5928 Overspeed error Movement disabled
D6202 Slow motion indicator, erroneous activation All functions are enabled
D6203 Slow motion indicator, erroneous shutdown All functions are enabled
D6302 Slow motion mode switch, erroneous activation All functions are enabled
D7002 High / low speed switch, erroneous activation (left lever) All functions are enabled
D7309 Low pressure in the service brake All functions are enabled
D7321 The pressure in the service brake is above the maximum permissible All functions are enabled
D7322 The pressure in the service brake is below the maximum permissible All functions are enabled
D8302 Stabilizers on / off valve output, erroneous activation All functions are enabled
D8303 Output of the valve on / off stabilizers, erroneous shutdown Control of stabilizers is not available
D8307 AVR ON / OFF valve output, open circuit AVR control not available
D8402 Feedback relay on / off stabilizers, erroneous inclusion All functions are enabled
D8403 Feedback relay on / off stabilizers, erroneous shutdown Control of stabilizers is not available
D8505 Left stabilizer lift output, short circuit to battery Control of stabilizers is not available
D8506 Left stabilizer lift output, ground fault Control of stabilizers is not available
D8507 Left stabilizer lift output, open circuit Control of stabilizers not available
D8605 Left stabilizer lowering output, short circuit to battery Control of stabilizers is not available
D8606 Left stabilizer lowering output, ground fault Control of stabilizers not available
D8607 Left stabilizer down output, open circuit Control of stabilizers is not available
D8705 Right stabilizer lifting output, short circuit to battery Control of stabilizers is not available
D8706 Right stabilizer lifting output, short to ground
D8707 Right stabilizer lift output, open circuit Control of stabilizers is not available
D8805 Right stabilizer lowering output, short circuit to battery Control of stabilizers is not available
D8806 Right stabilizer lowering output, ground fault Control of stabilizers is not available
D8807 Right stabilizer down output, open circuit Control of stabilizers is not available
D8902 Stabilizers activation switch, erroneous activation Stabilizers control is not available
D9099 Actuator calibration required Minimum current + tilt plate calibration All functions enabled
D9999 Invalid persistent data table not applicable
Service Code List — Workgroup Controller
The workgroup controller is located at the rear of the frame, to the left of the boom.
CODE DESCRIPTION RESULTS
W0321 Battery voltage above maximum limit Work equipment off
W0322 Low battery voltage below the minimum limit Work equipment off
W0721 Hydraulic oil temperature above maximum limit All functions enabled
W0722 Hydraulic oil temperature below minimum limit All functions enabled
W1005 PVG32 up / down valve, short to battery Boom up and down blocked
W1006 PVG32 up / down valve, ground fault Boom up and down blocked
W1028 PVG32 up / down valve, input error, main valve side diagnostics Boom up and down locked
W1105 PVG32 tilt valve, short to battery Tilt off
W1106 PVG32 tilt valve, short to ground Tilt off
W1128 PVG32 tilt valve, input error, main valve side diagnostics Tilt disabled
W1205 PVG32 extend / retract valve, short to battery Boom extend / retract blocked
W1206 PVG32 extend / retract valve, earth fault Boom extend / retract blocked
W1228 PVG32 extend / retract valve, input error, main valve side diagnostics Boom extend / retract blocked
W1305 PVG32 auxiliary valve, short to battery Auxiliary hydraulics disabled
W1306 Auxiliary valve PVG32, ground fault Auxiliary hydraulics disabled
W1328 PVG32 auxiliary valve, input error, diagnosis from the main valve side Auxiliary hydraulics disabled
W1405 PVG32 frame leveling valve, short to battery Frame leveling locked
W1406 PVG32 frame leveling valve, earth fault Frame leveling blocked
W1428 PVG32 frame alignment valve, input error, main valve side diagnostics Frame alignment blocked
W1824 Frame leveling potentiometer not in neutral Frame leveling locked
W3223 Invalid software or permanent data Work equipment off
W3228 Controller failure Work equipment disabled
W3296 Power off All functions enabled
W3297 Programmed by the controller All functions are enabled
W3304 No communication with gateway controller Work equipment is disabled
W3404 No communication with display controller Work equipment is disabled
W3604 No communication with the motor controller All functions are enabled
W3704 No signal from drive controller Auxiliary hydraulics disabled
W3804 No connection with LLMC Working group reduced
W3818 LLMC out of range Working group reduced
W3844 No LLMC compliance Working group reduced
W3845 No LLMC Compliance, Level 2 Stable Moves Disabled
W3904 No connection with LLMI Working group reduced
W3918 LLMI out of range Working group reduced
W4004 No communication with the joystick Work equipment is disabled
W4005 Joystick X-axis not in neutral (tilt) Tilt disabled
W4007 Joystick Y-axis not in neutral (lift) Lift disabled
W4010 Left joystick roller is not in neutral (extend and retract) Extend and retract disabled
W4028 Joystick handle failure Extend and retract disabled
W4204 No communication with receiver The orange carrycot error indicator on the transmitter flashes quickly. 3 beeps every 10 seconds on the transmitter.
W4205 Left joystick X-axis remote control disabled The orange cradle mode error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.
W4206 Right joystick X-axis remote control disabled The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.
W4207 Left joystick X-axis remote control disabled The orange cradle mode error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.
W4208 Right joystick X-axis remote control disabled The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.
W4215 Left joystick X-axis remote control error The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.
W4215 Left joystick X-axis remote control error The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.
W4216 Right joystick X-axis remote control error The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.
W4217 Left joystick Y-axis remote control error The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.
W4218 Right joystick Y-axis remote control error The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the transmitter.
W4320 Carrycot mode. The remote control is not connected to the cradle wiring (from the receiver CAN bus signal). The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps
every 10 seconds on the transmitter.
W4321 Cradle mode. The remote control is not connected to the carrycot wiring (from the receiver’s GACD controller status). The orange carrycot error indicator on the transmitter flashes rapidly.
3 beeps every 10 seconds on the transmitter.
W4325 Cradle mode. Cradle detection error. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4326 Cradle mode. The cradle was not found on the supporting structure. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4327 Cradle mode. The carrycot was not found on the supporting structure when the GACD controller is on or the remote control is in operation. Orange carrycot error indicator on transmitter
slowly
flashes. 3 beeps every 10 seconds on the transmitter.
W4330 Carrycot mode. Error in the operation of the cradle retraction switch. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4331 Carrycot mode. Expected boom extension not detected (boom retract switch on). The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the
transmitter.
W4335 Carrycot mode. Failure of the supports. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4336 Carrycot mode. The supports are not on the ground. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4340 Carrycot mode. Wrong arrow angle. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4341 Carrycot mode. Unexpected boom lift. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4342 Carrycot mode. No boom lift expected. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4343 Cradle mode. Boom angle exceeded. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4345 Cradle mode. LLM error. The red LLM indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4346 Carrycot mode. LLM in the lowered zone. The red LLM indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4347 Carrycot mode. Longitudinal stability: the maximum permissible value has been reached. The red LLM indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4350 Carrycot mode. Frame alignment failure. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4351 Carrycot mode. Boom alignment angle exceeded (out of range [-2 °; + 2 °]). The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the
transmitter.
W4355 Carrycot mode. Locking pin defective. The red lock indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter. W4356 Carrycot mode. The locking pin is
unlocked. The red lock indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4360 Carrycot mode. Failure due to overload of the carrycot. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4361 Cradle mode. Overloading the cradle. The carrycot overload indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4365 Cradle mode. Incorrect angle of inclination. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4366 Cradle mode. Tilt angle exceeded (out of range [-4 °; + 4 °]). The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4370 Cradle mode. FNR switch malfunction. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4371 Cradle mode. Parking brake malfunction. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4372 Cradle mode. Wrong position of the swivel washer. The orange carrycot error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W4404 Cradle mode. There is no communication with the GACD controller on the CAN bus. The orange carrycot error indicator on the transmitter flashes rapidly. 3 beeps every 10 seconds on the
transmitter.
W4621 Supply voltage 5 V to the voltage sensor above the maximum limit Work equipment off
W4622 5 V voltage supply to voltage sensor below minimum limit Work equipment off
W6021 Signal from inclinometer sensor above maximum limit All functions enabled
W6022 Signal from inclinometer sensor below minimum limit All functions enabled
W6098 Calibration complete All functions enabled
W6099 Calibration required All functions enabled
W6102 Inclination indicator, switch-on error All functions enabled
W6103 Inclination indicator, shutdown error All functions enabled
W6521 Boom angle 1 above maximum limit All functions enabled
W6522 Boom angle 1 below minimum limit All functions enabled
W6621 Boom angle 2 above maximum limit All functions enabled
W6622 Boom angle 2 below minimum limit All functions enabled
W6744 Wrong boom angle All functions enabled
W6798 Boom angle calibration performed All functions enabled
W6799 Boom angle calibration required All functions enabled
W6802 Boom retract switch, short to battery All functions enabled
W6803 Boom retract switch, short to ground or open circuit All functions enabled
W8002 Quick-Tach power out, erroneous power-up Quick-Tach power function not available
W8003 Quick-Tach power out, erroneous shutdown Quick-Tach power function not available
W8007 Quick-Tach power output, open circuit Quick-Tach power is off
W8128 Quick-Tach Power Switch in Error State Quick-Tach Disabled
W8202 Quick-Tach power relay feedback, erroneous activation Quick-Tach function disabled
W8203 Quick-Tach power relay feedback, erroneous shutdown Quick-Tach function disabled
W8502 Platform Detect Switch Closed The orange cradle mode error light on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W8503 A short or open circuit in the work platform detection switch. The orange cradle mode error indicator on the transmitter flashes slowly. 3 beeps every 10 seconds on the transmitter.
W9999 Invalid workgroup controller table Applicable
Service Code List — Display Controller
Service Code List — LLMI System Controller
CODE DESCRIPTION RESULTS
L0102 Left panel button 1, erroneous activation Working light button does not work Cannot access calibration menu for control mode and battery voltage
L0202 Button 2 of the left panel, erroneous activation Joystick lock button does not work
Unable to change the state of the safety valve Unable to access the angle calibration menu
L0302 Button 3 left panel, erroneous activation Auxiliary hydraulics button does not work
Unable to change constant flow status Unable to access the pump menu of the drive
L0402 Left panel button 4, erroneous activation Information button does not work Cannot change the displayed menu
L7404 No communication with the main controller Data is not displayed / functions on the display are prohibited
L7672 Left panel software error Data not displayed / functions prohibited on display
Service Code List — LLMI System Controller
CODE DESCRIPTION RESULTS
I3014 LLMI system EEPROM failure LLMI is not displayed, workgroup functions are reduced
I3015 Failure of the external LLMI trigger signal
LLMI is not displayed, workgroup functions are reduced
I3018 Invalid RAM check LLMI LLMI is not displayed, workgroup functions are reduced
I3016 Incorrect check of the checksum of the LLMI program
LLMI is not displayed, workgroup functions are reduced
I3113 LLMI check button error Check not available
I3121 LLMI sensor ID error LLMI is not displayed, workgroup functions are reduced
I3122 LLMI sensor offset LLMI is not displayed, the functions of the working group are reduced
I3123 LLMI sensor reading out of LLMI range is not displayed, workgroup functions are reduced
I0314 Reception of LLMI sensor outside of LLMI delay is not displayed, workgroup functions are reduced
I0315 LLMI sensor failure LLMI is not displayed, the functions of the working group are reduced
I3014 LLMI calibration values out of range
LLMI is not displayed, workgroup functions are reduced
I3015 LLMI calibration values inverted LLMI not displayed, workgroup functions reduced
I3018 LLMI calibration values too close
LLMI is not displayed, workgroup functions are reduced
I3016 LLMI calibration timeout LLMI not displayed, workgroup functions reduced
I3113 Undervoltage LLMI LLMI is not displayed, the functions of the work group are reduced
I3121 Overvoltage LLMI LLMI is not displayed, the functions of the work group are reduced
Service Code List — LLMC Controller
CODE DESCRIPTION RESULTS
C3801 LLMC System EEPROM Failure Workgroup Functions Reduced
C3803 Failure of the external LLMC trigger signal Run group functions reduced
C3804 Invalid LLMC RAM Check Run Group Functions Reduced
C3805 Invalid LLMC Program Checksum Verification Workgroup Functions Reduced
C3017 LLMC Sensor ID Error Run Group Function Reduced
C3014 LLMC Sensor Offset Working Group Functions Reduced
C3015 LLMC sensor reading out of range Run group functions reduced
C3018 LLMC Sensor Reception Out of Delay Run Group Functions Reduced
C3016 LLMC Sensor Failure Run Group Functions Reduced
C3113 LLMC calibration values out of range Rungroup functions reduced
C3121 LLMC Calibration Values Inverted Run Group Functions Reduced
C3122 LLMC Calibration Values Too Close Workgroup Functions Reduced
C3123 LLMC Calibration Timeout Run Group Functions Reduced
C0314 LLMC undervoltage Working group functions reduced
C0315 LLMC overvoltage Working group functions reduced