-
submitred
Пользователь- Регистрация:
- 25.05.2015
- Сообщения:
- 868
- Симпатии:
- 73
Всем привет. Бокс фрибутный. Ошибка на фрибуте 1021, толковой инфы не нашёл. Перекатал проц, залил универсальный фрибут, чип новый поставил, xell стартует, фрибут ошибка. Кто сталкивался с такой проблемой, отпишитесь пожалуйста. Пишут что это проблема gpu, но на двух процах врятли одна и та-же ошибка могла выскочить. Кто-то писал за юг. Ещё не менял, может кто-то победил такую?
-
Nik29-7777
Пользователь- Регистрация:
- 26.04.2017
- Сообщения:
- 1.046
- Симпатии:
- 150
ну вполне может быть связана в обрыве , перегнивших дорожках — кондеры ,резюки которые связывают проц и мост .
-
submitred
Пользователь- Регистрация:
- 25.05.2015
- Сообщения:
- 868
- Симпатии:
- 73
Мелочёвку всё проверил, обрыва нет. Буду менять юг.
-
submitred
Пользователь- Регистрация:
- 25.05.2015
- Сообщения:
- 868
- Симпатии:
- 73
Заменил юг, результата нет. Ошибка 1021.
-
Okas43
Пользователь- Регистрация:
- 18.01.2017
- Сообщения:
- 1.366
- Симпатии:
- 133
многие говорят хана или юг. но если юг и проц менял. тогда хз
-
submitred
Пользователь- Регистрация:
- 25.05.2015
- Сообщения:
- 868
- Симпатии:
- 73
Ещё писали что может быть из-за сети, но в xell подкидывал кабель, ip адрес консоль получила. Значит проблема не в нём. Остаётся только память заменить…
-
submitred
Пользователь- Регистрация:
- 25.05.2015
- Сообщения:
- 868
- Симпатии:
- 73
Может кто глянуть какое напряжение должно быть на этом дроселе. У меня 0В. Странное поведение, если отключить кабель hdmi, консоль работает, чип мигает, и в момент запуска, когда ресеты прекращаются, консоль должна стартовать, в этот момент выдавало ошибку с кабелем, без кабеля ошибки нет.
-
Nik29-7777
Пользователь- Регистрация:
- 26.04.2017
- Сообщения:
- 1.046
- Симпатии:
- 150
нормальное поведение так и должно быть — консоль не будет давать огней приветствия без подключенного кабеля.
нет приветствия нет старта нет ошибки. -
submitred
Пользователь- Регистрация:
- 25.05.2015
- Сообщения:
- 868
- Симпатии:
- 73
Сопротивление gpu 45 Ом, по-моему это много. Сопротивление cpu 5 Ом. Если мне память не изменяет, то гпу должно быть порядка 4 Ом… Напряжения на gpu 1.3V на cpu 1.13V.
Последнее редактирование: 21.02.2021
-
Nik29-7777
Пользователь- Регистрация:
- 26.04.2017
- Сообщения:
- 1.046
- Симпатии:
- 150
по разному . минимальное видел 3 . максимум около 8 цпу
гпу от 25 до 50 -
Nik29-7777
Пользователь- Регистрация:
- 26.04.2017
- Сообщения:
- 1.046
- Симпатии:
- 150
кондеры визуально проверяли ? или все таки заменой или хотя бы прибором ?
-
Nik29-7777
Пользователь- Регистрация:
- 26.04.2017
- Сообщения:
- 1.046
- Симпатии:
- 150
2 пары их по 4 шт от моста . на той что ближе к процу на 4х от проца в режиме прозвонки все 4 точки примерно одинаково должны звонится около 600-800 . те что ближе к мосту поменьше 400-600 это точки от проца . и точки от моста тоже просморите.
-
submitred
Пользователь- Регистрация:
- 25.05.2015
- Сообщения:
- 868
- Симпатии:
- 73
Клиент всегда ВРЁТ! Когда отдавали на ремонт, сказали что вечером поиграли, а утром она не включилась. Ничего не делали. Консоль починил. Оказался сбитый элемент под процом, с обратной стороны. Запаял с донора, консоль успешно стартанула. Ещё раз повторю, КЛИЕН ВСЕГДА ВРЁТ.
-
Nik29-7777
Пользователь- Регистрация:
- 26.04.2017
- Сообщения:
- 1.046
- Симпатии:
- 150
-
Okas43
Пользователь- Регистрация:
- 18.01.2017
- Сообщения:
- 1.366
- Симпатии:
- 133
-
Acousticks
Модератор- Регистрация:
- 04.08.2011
- Сообщения:
- 5.150
- Симпатии:
- 1.024
И как ты его там разглядел только)
-
ЯРЫЙ
- Регистрация:
- 01.12.2012
- Сообщения:
- 8.587
- Симпатии:
- 1.336
Я об этом всегда говорю
Поделиться этой страницей
Here is a full list of known error codes and fixes (if available).
To jump to the error your looking for simply press Ctrl+F to bring up search and write in your error code.
Took me forever to write up and get sorted so i hope you appreciate it
Credits to xbox-experts
Quote: How to tell what error code your Xbox360 has (credits to uncle Az):
- Turn the xbox 360 on, and wait till the 3 red lights are flashing.
- Press and hold the sync up button (the small white one), while holding that button press the eject button.
- The LEDs will now blink the first number in the code (as described below).
- Release the eject button and press it again.
- The LEDs will now blink the second number of the code.
- Release the eject button and press it again.
- The LEDs will now blink the third number of the code.
- Release the eject button and press it again.
- The LEDs will now blink the forth number of the code.
- Release the eject button and press it again.
- The LEDs will go back to the 3 red flashing lights.
- You should be able to determine the difference between the 3 flashing lights and the error code lights by the rate in which they flash.
Here is how you interpret the LEDs to get the code number:
- All four lights flashing — 0
- One light flashing — 1
- Two Lights flashing — 2
- Three lights flashing — 3
Quicklist of error codes:
Code:
Ecode’sE00
E01
E02
E03
E04
E08
E09
E10
E11
E12
E13
E14
E15
E16
E17
E18
E19
E20
E21
E22
E23
E24
E25
E27
E28
E29
E30
E31
E32
E33
E34
E35
E36
E37
E38
E39
E40
E41
E42
E43
E44
E45
E46
E47
E56
E57
E58
E59
E60
E61
E62
E63
E26
E48
E49
E50
E51
E52
E53
E54
E55
E64
E65
E66
E67
E68
E69
E70
E71
E72
E73
E74
E75
E76
E77
E78
E79
E80Secondary’s
0000
0001
0002
0003
0010
0011
0012
0013
0020
0021
0022
0023
0030
0031
0032
0033
0100
0111
0112
0113
0120
0121
0122
0123
0130
0131
0132
0133
0200
0201
0202
0203
0210
0211
0212
0213
0220
0221
0222
0223
0230
0231
0232
0233
0300
0301
0302
0303
0310
0311
0312
0313
0320
0321
0322
0323
0330
0331
0332
0333
1000
1001
1002
1003
1010
1011
1012
1013
1020
1021
1022
1023
1030
1031
1032
1033
1100
4444
0 RLOD Error (normal) codesE-Code / Secondary Error code: E26 / 0122
Binary/Hex: 00011010 / 0x1A -> 26Known fixes:
1) Apply new thermal paste, make sure the heatink is making contact with the heat spreader
Description:
This is the overheating code for the Xbox 360 slim for the CPU/GPU unit.
«I overheated my 360 and when it overheated the airflow temp was a 69C.
Also you get the seccondary error codes the same way as a regular 360.
Also it has green leds not red lol.
And differant error codes 0122 is now the new overheating code.
vid: http://www.youtube.com/watch?v=j6zc_knTszQ»___________________________________________________
E-Code / Secondary Error code: — (No Audio/Video) / —
Binary/Hex: 00000000 / 0x00 -> 0Known fixes:
1) X-Clamp replacement — tighten the screws on the side facing the HANA chip slightly more
2) Reflow GPU and HANA chipRelated Errors: E74
Description:
This error is caused by a cold solder joint in the GPU — HANA chip area, like E74.The 360 doesnt recognize it yet though.
__________________________________________________
E-Code / Secondary Error code: — (No Audio/Video) / —
Binary/Hex: 00000000 / 0x00 -> 0Known fixes:
1) Scan the mainboard and make sure that there is nothing that might short something out, like metal chipping, components, that move out of place while heatgunning, etc.
2) X-Clamp replacement
The GPU heatsink might be shorting out if you screwed it in too tight…
3) Reflow the solder
In rare cases a reflow might also fix it.Description:
This error can be triggered by a faulty power supply or a short in the console.The short is located near one of the main supply lines, so not under the chips, it might also be a blown capacitor fuse or just a bridged contact.
___________________________________________________
1 RLOD Error codes
E-Code / Secondary Error code: E64 / 1000
Binary/Hex: 01000000 / 0x40 -> 64Known fixes:
1) Check the DVD power and SATA cable for damages and replace them if necessary.
2) If you have soldered a modchip to the drive recently make sure it is sinstalled properly otherwise the flash chip isnt powered.
3) The flash chip must be desoldered and reflashed with an external programmer, recover the dvd-key if you can (unless you have a backup)…Description:
This error occurs if something goes wrong while flashing the drive or installing a modchip.A sign for it is that the dvd-drive doesnt eject the tray anymore.
DVD drive timed out during reset.
It can also be caused by a faulty DVD power or SATA cables(edsondario & Fios89)_________________________________________________
E-Code / Secondary Error code: E65 / 1001
Binary/Hex: 01000001 / 0x41 -> 65Known fixes:
1)If you have soldered a modchip to the drive recently make sure it is installed properly otherwise the flash chip isnt powered.
2) Try to reflash the correct firmware to the drive using your computer.
3) The flash chip must be desoldered and reflashed with an external programmer, recover the dvd-key if you can (unless you have a backup)…Description:
This error occurs if something goes wrong while flashing the drive or installing a modchip.A sign for it is that the dvd-drive can still be flashed and read out.
According to XBH: DVD drive is not DMA configured_________________________________________________
E-Code / Secondary Error code: E66 / 1002
Binary/Hex: 01000010 / 0x42 -> 66Known fixes:
1) Reflash the firmware with the correct Vendor version string using your computer.
Description:
This error occurs when you replace the dvd-drive and forget to spoof it with the correct version string of the drive you replaced….
__________________________________________________
E-Code / Secondary Error code: E67 / 1003
Binary/Hex: 01000011 / 0x43 -> 67Known fixes:
1) Replace your harddrive.
2) If you know it isnt the harddrive try the Southbridge X-Clamp Fix or Reflow the SouthbridgeDescription:
This error occurs when your harddrive is defective, it might still work sometimes….Hard drive timed out during reset. There is also a small chance that it is a cold joint under the Southbridge causing problems with the I/O of the HDD.__________________________________________________
E-Code / Secondary Error code: E68 / 1010
Binary/Hex: 01000100 / 0x44 -> 68Known fixes:
1) If you recently used it with a computer you might have got a faulty security sector or so..
2) Replace your harddrive.
3) Southbridge X-Clamp Fix
4) Reflow the SouthbridgeDescription:
This error occurs when your harddrive is defective, it might still work sometimes…. It can also happen because of a bad eeprom or a wrong security sector.It can also be a problem with the internal connection of the harddrive to the mainboard…According to XBH: Hard drive not DMA configured
__________________________________________________
E-Code / Secondary Error code: E69 / 1011
Binary/Hex: 01000101 / 0x45 -> 69Known fixes:
1) Unplug your harddrive and plug it back in
2) If you played around with HDDHackr the hddss.bin could be invalid, try reflashing it and make sure your dump is good.
3) Replace your harddrive.Description:
This error occurs when your harddrives security sector is unreadable, if you have played around with that make sure to have the correct security sector on the drive….
However it could also just be defective and trigger the error because of that.__________________________________________________
E-Code / Secondary Error code: E70 / 1012
Binary/Hex: 01000110 / 0x46 -> 70Known fixes:
No Known fixes available!
Description:
HDD Error (Corrupt Filesystem/partitions) or Hard drive not found
__________________________________________________
E-Code / Secondary Error code: E71 / 1013
Binary/Hex: 01000111 / 0x47 -> 71Known fixes:
1) Patch for the fall update(search on Google for it)/ Insert the NXE Update disc before the error screen pops up
2) Reflow the Southbridge
3) Southbridge X-Clamp Fix
4) If Software related, the JTAG Hack might work to fix it.Description:
This error is related to a failed dashboard update, can also be NAND related if you have an Infectus chip….
It can also often be caused by a cold joint under the Southbridge(if it wasnt caused by an update).
According to XBH: Error within Xam___________________________________________________
E-Code / Secondary Error code: E72 / 1020
Binary/Hex: 01001000 / 0x48 -> 72Known fixes:
1) Patch for the fall update(search on Google for it)/ Insert the NXE Update disc before the error screen pops up
2) Reflow the Southbridge
3) Southbridge X-Clamp Fix
4) If Software related, the JTAG Hack might work to fix it.Description:
This error is related to a loose pin or a not existent NAND chip, can also happen if you flashed it badly with an Infectus chip and/or the NAND is dead….
According to XBH: Error within Xam___________________________________________________
E-Code / Secondary Error code: E73 / 1021
Binary/Hex: 01001001 / 0x49 -> 73Known fixes:
1) Southbridge X-Clamp-Fix
2) Reflow the Southbridge/Ethernet chip area
3) Check the area under the Southbridge for parts that might have fallen off and solder them back on.
4) In rare cases it can also be GPU related so an X-Clamp Fix might work as well (bigart666)Description:
This error is caused by a cold solder joint under the Southbridge or the ethernet chip.In rare cases it can also be triggered by a cold joint under the GPU on one of the lines that run to the Southbridge chip.
And missing parts(caps, resistors…) under the Southbridge can trigger this error as well.____________________________________________________
E-Code / Secondary Error code: E74 / 1022
Binary/Hex: 01001010 / 0x4A -> 74Known fixes:
1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU.
2) X-Clamp replacement Hybrid — Tighten the GPU screws facing the HANA chip slightly more and make sure to be using a shim
2) X-Clamp replacement Hybrid — Tighten the GPU screws facing the HANA chip slightly more and make sure to be using a shim. Adding an extra shim on each side of the smaller chip dye will help to create more surface against the heatsink and will increase the chances of the error going away for good.
3) If there is a lot of flexing under the GPU, bake the board to unflex it
4) Reflowing GPU and HANA chipRelated Errors:
0022
Description:
This error is caused by a cold solder joint under the GPU, (H)ANA-chip or in between.
Mostly it is one of the outer solder ***** on the side facing the (H)ANA chip so a shim increases the chanced of success quite a bit.
Can also be a component that is missing or damaged so look for missing parts near the GPU and the (H)ANA chip.____________________________________________________
E-Code / Secondary Error code: E75 / 1023
Binary/Hex: 01001011 / 0x4B -> 75Known fixes:
1) Connect the DVD-drive and check if the error code is still the same…
2) Remove everything you might have soldered to this area.
3) Reflow the Southbridge and Networkchip …
4) Replace the NetworkchipDescription:
This error is related to the network chip, might be power related or so.This can happen while installing and NME 2.
In general it sounds like a cold solder joint somewhere there.However it can also be a Hitachi DVD-drive that is not connected…
According to XBH: Couldn’t read ethernet phy vendor/wrong ethernet vendor____________________________________________________
E-Code / Secondary Error code: E76 / 1030
Binary/Hex: 01001100 / 0x4C -> 76Known fixes:
1) Replace the Networkchip
2) Connect the DVD-drive and check if the error code is still the same…
3) Remove everything you might have soldered to this area.
4) Reflow the Southbridge and Networkchip …Description:
This error is caused by a dead network chip.This can happen when a lightning hits your house and the network chip is under high voltage.
According to XBH: Couldn’t complete ethernet reset_____________________________________________________
E-Code / Secondary Error code: E77 / 1031
Binary/Hex: 01001101 / 0x4D -> 77Known fixes:
1) Replace the Network chip and other damaged components around it like blown capacitors defective regulators etc…
2) Reflow the Southbridge and Networkchip …Related Errors:
E76
Description:
This error is caused by a dead network chip.
It can occur when your house gets hit in a thunderstorm…
According to XBH: phy request is already processing/ reading reg failed/ Failed to write reg____________________________________________________
E-Code / Secondary Error code: E78 / 1032
Binary/Hex: 01001110 / 0x4E -> 78Known fixes:
No Known fixes available!
Description:
AsicId check failed
____________________________________________________
E-Code / Secondary Error code: E79 / 1033
Binary/Hex: 01001111 / 0x4F -> 79Known fixes:
1) Replace your harddrive.
2) If you know it isnt the harddrive try the Southbridge X-Clamp Fix or Reflow the Southbridge
3) Check JTAG wiring! Especially the diodes they MUST face the correct direction — Away from J2D2.Description:
This error occurs when your harddrive is defective, it might still work sometimes….
There is also a small chance that it is a cold joint under the Southbridge causing problems with the I/O of the HDD.
It can also be related to wiring the diodes while JTAGGING.
Couldn’t start xam.xex_____________________________________________________
E-Code / Secondary Error code: E80 / 1100
Binary/Hex: 01010000 / 0x50 -> 80Known fixes:
1) Downgrade to the old dashboard, solder the resistor back on and then update your xbox.
2) If you have the CPU Key, get the current NAND Flash image and fix the LDV (Just add 1 up to latest kernel).Description:
Wrong LDV version in NAND Flash. You have the new dashboard update but not the resistor R3T6, follow known fixes to see how to resolve the problem.
_____________________________________________________
2 RLOD Error codes
E-Code / Secondary Error code: E05 (No Audio/Video) / 0011
Binary/Hex: 00000101 / 0x05 -> 5Known fixes:
1) Make sure the CPU heatsink is making good contact with the chip, apply a thin layer of compound and put the heatsink on without screws, make sure it gives a good imprint then.
2)Replacing the CPU X-Clamps/Applying new thermal compound
3) Cut the temperature sensor traceDescription:
This error appears when the CPU overheated, after that the xbox locks itself until it cooled the chip down.The reason for that is that the heat cant be dissipated to the heatsink/ the heatsink isnt cooled properly…
This can be the result of improper thermal compound usage or if the error comes up instantly while booting the console, the heatsink will likely not be making any contact at all with the chip.
In rare cases it can also be a faulty temp sensor._____________________________________________________
E-Code / Secondary Error code: E06 (No Audio/Video) / 0012
Binary/Hex: 00000110 / 0x06 -> 6Known fixes:
1) Make sure the CPU heatsink is making good contact with the chip, apply a thin layer of compound and put the heatsink on without screws, make sure it gives a good imprint then.
2)Replacing the GPU X-Clamps/Applying new thermal compound
3) It can also be fixed sometimes by just a slight tightening the GPU bolts,(1/4 or 1/8 turn). xboxgamer815Description:
This error appears when the GPU overheated, after that the xbox locks itself until it cooled the chip down.The reason for that is that the heat cant be dissipated to the heatsink/ the heatsink isnt cooled properly…
This can be the result of improper thermal compound usage or if the error comes up instantly while booting the console, the heatsink will likely not be making any contact at all with the chip._____________________________________________________
E-Code / Secondary Error code: E07 (No Audio/Video) / 0013
Binary/Hex: 00000111 / 0x07 -> 7Known fixes:
1) Putting the faulty RAM brick under pressure with a 3mm thick craft foam pad.
2) Reflow the RAM chips — Oven Reflow preferably for the bottom RAM
— Reflow the 2 ram bricks under the GPU heatsink 99% of the time its these that are causing the error.(DCP)
3) Hybrid X-Clamp FixDescription:
In 99% of the cases it is a cold solder joint under one of the RAM bricks though.
It is also said to be an indicator for RAM overheating but this is extremely rare_____________________________________________________
3 RLOD Error codes
E-Code / Secondary Error code: E00 (No Audio/Video) / 0000
Binary/Hex: 00000000 / 0x00 -> 0Known fixes:
1) Blow the dust away under the Southbridge and HANA chip
2) Reflow the Southbridge
3) X-Clamp replacementDescription:
The Xbox doesnt know whats wrong it freezes after showing the first digit(0) of the error code.Might be a cold solder joint somewhere under the GPU as someone fixed it with the X-Clamp replacement, might also be scaler or Southbridge related since this is where the error code is calculated…
According to stephen.a.j it can also be caused by dust under the Southbridge and the HANA chip so please check for that…
_____________________________________________________
E-Code / Secondary Error code: E01 (No Audio/Video) / 0001
Binary/Hex: 00000001 / 0x01 -> 1Known fixes:
1) Make sure your PSU is working and replace it if it isnt
2) Scan the mainboard and make sure that there is nothing that might short something out, like metal chipping, components, that move out of place while heatgunning, etc.
3) Replace MOSFETs and regulators that are known to cause it if they were blown
4) Check if the standby voltages are existent, if they are not at a certain area replace the parts in the area which are likely to be defective.
5) Reflow the CPU, HANA chip
In rare cases a reflow might also fix it.
6) X-Clamp replacement
The GPU heatsink might be shorting out if you screwed it in too tight…Description:
This error can be triggered by a faulty power supply or a short in the console. The short is located near one of the main supply lines, so mostly not under the chips, it might also be a blown capacitor fuse or just a bridged contact. Also damaged DVD power cable.
_____________________________________________________
E-Code / Secondary Error code: E02 (No Audio/Video) / 0002
Binary/Hex: 00000010 / 0x02 -> 2Known fixes:
1) Scan the mainboard and make sure that there is nothing that might short something out, like metal chipping, components, that moved out of place while reflowing, etc. — Especially in the CPU area
3) Replace MOSFETs and regulators that are known to cause it if they were blown
4) Check if the standby voltages are existent, if they are not at a certain area replace the parts in the area which are likely to be defective.
5) Reflow the CPU
6) X-Clamp replacementDescription:
This error code is caused by a cold solder joint under the CPU or by a problem with the way it is powered(blown mosfet, capacitor or a short)
According to xbox-scene it is also a problem with the ethernet chip but there arent any references for that._____________________________________________________
E-Code / Secondary Error code: E03 (No Audio/Video) / 0003
Binary/Hex: 00000011 / 0x03 -> 3Known fixes:
1) Scan the mainboard and make sure that there is nothing that might short something out, like metal chipping, components, that moved out of place while reflowing, etc. — Especially in the CPU area
2) Replace MOSFETs and regulators that are known to cause it if they were blown
3) Check if the standby voltages are existent, if they are not at a certain area replace the parts in the area which are likely to be defective.
4) Reflow the CPU
5) X-Clamp replacementRelated Errors:
0001
Description:
The CPU is somehow not getting clean power, can be a cold solder joint under it or one of the external parts like a missing cap etc.
_____________________________________________________
E-Code / Secondary Error code: E04 (No Audio/Video) / 0010
Binary/Hex: 00000100 / 0x04 -> 4Known fixes:
1) Southbridge X-Clamp-Fix
2) Reflow the Southbridge area
3) Check the area under the Southbridge for parts that might have fallen off and solder them back on.Description:
There is a problem with the Southbridge Chip usually dealing with how it connects to the mainboard (cold solder joint/bridged solder joints)(Taken from Xbox-Scene)
_____________________________________________________
E-Code / Secondary Error code: E08 (No Audio/Video) / 0020
Binary/Hex: 00001000 / 0x08 -> 8Known fixes:
1)If you worked on the mainboard recently(soldered or so) remove these wires because you might be drawing too much power from the GPU
Also look for missing/bridged components like capacitors/resistors
2) If you jtagged the console remove wires and resistors, the parallel port can stay as long as no PC is connected.
3) X-Clamp replacement
4) Flush with alcohol, let dry, begin Relow with flux like below
5) Reflow GPU (and RAM if this fails) area
6) Reball the GPU and RAM, for bridged solderDescription:
This error is caused by a bridged solder joint under CPU, GPU or one of the RAM bricks.
This effect can also be caused by tin whiskers leading to shorts and if the GPU was taken off the mainboard this error will also show up.
It can also be power related(the CPU/GPU or RAM isnt getting enough power). Can also be a component that is missing or damaged so look for missing and bridged parts near the GPU.
If the console was jtagged and the resistors and cables are still connected it will show 0020, the parallel port can stay as long as no PC is connected._____________________________________________________
E-Code / Secondary Error code: E09 (No Audio/Video) / 0021
Binary/Hex: 00001001 / 0x09 -> 9Known fixes:
1)If you worked on the mainboard recently(soldered or so) remove these wires because you might be drawing too much power from the Southbridge
Also look for missing/bridged components like capacitors/resistors
2) X-Clamp replacement
3) Southbridge X-Clamp-Fix
4) Reflow the Southbridge/Ethernet chip area
5) Reball the Southbridge — bridged solder
6) if you work in dumping lite-on 8xxxx and 9xxxx with jumper, Check your dvd drive pcb (board) again, if there’s still some shorting.Related Errors:
1021
Description:
This error is caused by a bridged solder joint under GPU or Southbridge. It can also be power related(the Southbridge isnt getting enough power). Can also be a component that is missing or damaged so look for missing and bridged parts(caps etc) near the Southbridge
_____________________________________________________
E-Code / Secondary Error code: E10 (No Audio/Video) / 0022
Binary/Hex: 00001010 / 0x0A -> 10Known fixes:
1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU.
2) X-Clamp replacement
3) Reflow GPU and HANA chip
4) If it’s not the GPU/(H)ANA, it might in rare cases be the CPU and can be fixed by reflowing the CPU.
5) if you flash with xell on JTAG-fixed xbox360 this will appear, flash back to original.
6) also can be caused by a broken trace (see link below).Description:
This error is caused by a bridged/shorting solder joint under the GPU, (H)ANA-chip or in between.It can also be power related though, for example if you are drawing power from one of the regulators that power the GPU and HANA-chip.Can also be a component that is missing or damaged so look for missing parts near the GPU and the HANA chip. In extremely rare cases it might also be related to the lines that lead from HANA to the CPU.
The chances are however higher that it is the GPU than the HANA chip so you should always first concentrate on the GPU.Another cause could be due to a broken trace under the board near one of the ram blocks, check the picture in the reference section. Thank you arvydas for reporting this solution!
_____________________________________________________
E-Code / Secondary Error code: E11 (No Audio/Video) / 0023
Binary/Hex: 00001011 / 0x0B -> 11Known fixes:
No Known fixes available!
Related Errors:
0021
Description:
This error is unknown but assumed to be a short either under Southbridge and (H)ANA chip or in between these.Look for 0021 and 0022 and reflow the Southbridge-> HANA chip area, the X-Clamp Fix might help as well.
_____________________________________________________
E-Code / Secondary Error code: E12 (No Audio/Video) / 0030
Binary/Hex: 00001100 / 0x0C -> 12Known fixes:
1) Replacing the X-Clamps
2) Reflowing the CPU
Concentrate on the CPU.
3) Cutting the CPUs temp sensor trace.Description:
The temp sensor is not working properly, maybe because it is shorting out (2 bridged solder *****).Or it is broken, then you have to cut the trace…
_____________________________________________________
E-Code / Secondary Error code: E13 (No Audio/Video) / 0031
Binary/Hex: 00001101 / 0x0D -> 13Known fixes:
1) Reflow the RAM and Southbridge
2) Loosen your heatsink screws and make sure the heatsink isnt shorting out a capacitor…
3) Replace the faulty RAM brick
4) X-Clamp replacement
5) Replace dvd power cord. Short in the dvd drive cord or the cord is in backwards.
6) un-bridged U6T1 or U6T2 (point that protect cpu-fuse)Description:
This error is caused by a faulty/cracked RAM brick, however it can also be caused when the heatsink is shorting out a resistor or like a bad solder joint under the GPU?, check out the links in the references…
Also caused by the Southbridge if not properly soldered to motherboard or if it experiences a power short.
Can be caused by a backwards power cord or faulty power cord to dvd player.— if you update to freeboot 9199 with bridged U6T1 or U6T2 this error will appear, unbridged it (Shadow-Wizzard)
_____________________________________________________
E-Code / Secondary Error code: E14 (No Audio/Video) / 0032
Binary/Hex: 00001110 / 0x0E -> 14Known fixes:
No Known fixes available!
Related Errors:
0030
Description:
Might be temp sensor related, check out 0030
_____________________________________________________
E-Code / Secondary Error code: E15 (No Audio/Video) / 0033
Binary/Hex: 00001111 / 0x0F -> 15
Known fixes:No Known fixes available!
Related Errors:
0030
Description:
Might be temp sensor related, check out 0030
_____________________________________________________
E-Code / Secondary Error code: E16 (No Audio/Video) / 0100
Binary/Hex: 00010000 / 0x10 -> 16Known fixes:
1) X-Clamp replacement
2) Reflowing the GPURelated Errors:
0102
Description:
This error is a Cold solder joint under the GPU just like 0102, can be fixed with the X-Clamp replacement.
_____________________________________________________
E-Code / Secondary Error code: E17 (No Audio/Video) / 0101
Binary/Hex: 00010001 / 0x11 -> 17Known fixes:
1) Unplug all USB devices that might be connected to your 360
2) Remove solder from the pins under the USB ports so that they are not shorting out anymore, also check the ports themselves and make sure that the pins inside arent bridgingDescription:
This error is caused by bridged solder joints under the USB ports or a defective USB device that is connected to it.
_____________________________________________________
E-Code / Secondary Error code: E18 (No Audio/Video) / 0102
Binary/Hex: 00010010 / 0x12 -> 18Known fixes:
1) X-Clamp replacement
2) Reflow GPU and RAMDescription:
This error is caused by a cold solder joint under CPU, GPU or one of the RAM bricks. Can also be a component that is missing or damaged so look for missing parts near the GPU.
_____________________________________________________
E-Code / Secondary Error code: E19 (No Audio/Video) / 0103
Binary/Hex: 00010011 / 0x13 -> 19Known fixes:
1) Remove short circuit from bridged capacitor under the GPU
2) X-Clamp replacement
3) Reflow CPU/GPU/RAMRelated Errors:
0102
Description:
This error can either be caused by a cold solder joint under the GPU or a bridged capacitor under it(power problem)
_____________________________________________________
E-Code / Secondary Error code: E20 (No Audio/Video) / 0110
Binary/Hex: 00010100 / 0x14 -> 20Known fixes:
1) Reflow the RAM
2) Loosen your heatsink screws and make sure the heatsink isnt shorting out a capacitor…3) Look for missing and bridged components like resisitors and caps and replace them4) X-Clamp replacementDescription:
This error is caused by a cold solder joint under one of the RAM chips, mostly its the top ones, sometimes it can also be one of the solder ***** under the GPU that lead to the RAM. Update:According to stephen a.j it can also be cause by a broken trace that connects the GPU and the RAM, the reason for it to break could be the flexing in this certain area.
_____________________________________________________
E-Code / Secondary Error code: E21 (No Audio/Video) / 0111
Binary/Hex: 00010101 / 0x15 -> 21Known fixes:
No Known fixes available!
Related Errors:
0110
Description:
This error is unknown but could be somehow related to a cold solder joint under the RAM.On xbox-scene there was also a post in which was claimed that it has to do with the NAND
_____________________________________________________
E-Code / Secondary Error code: E22 (No Audio/Video) / 0112
Binary/Hex: 00010110 / 0x16 -> 22Known fixes:
No Known fixes available!
Related Errors:
0110
Description:
This error is totally unknown, probably it is RAM related like 0110
_____________________________________________________
E-Code / Secondary Error code: E23 (No Audio/Video) / 0113
Binary/Hex: 00010111 / 0x17 -> 23Known fixes:
No Known fixes available!
Related Errors:
0110
Description:
This error is totally unknown, probably it is RAM related like 0110
_____________________________________________________
E-Code / Secondary Error code: E24 (No Audio/Video) / 0120
Binary/Hex: 00011000 / 0x18 -> 24Known fixes:
1) Penny fix on RAM
Related Errors:
0110
Description:
This error is unknown but someone on xbox-scene could fix it using the penny fix.Could be a short in the area under the RAM that causes 0110 when there is a cold solder joint.
If it was like usual the error code would be 0020._____________________________________________________
E-Code / Secondary Error code: E25 (No Audio/Video) / 0121
Binary/Hex: 00011001 / 0x19 -> 25Known fixes:
1) Replacing the X-Clamps
2) Reflowing the CPUDescription:
Cold solder joint under CPU
-> The CPU cant communicate with the mainboard_____________________________________________________
E-Code / Secondary Error code: E27 (No Audio/Video) / 0123
Binary/Hex: 00011011 / 0x1B -> 27Known fixes:
No Known fixes available!
Description:
The error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E28 (No Audio/Video) / 0130
Binary/Hex: 00011100 / 0x1C -> 28Known fixes:
No Known fixes available!
Description:
The error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E29 (No Audio/Video) / 0131
Binary/Hex: 00011101 / 0x1D -> 29Known fixes:
No Known fixes available!
Description:
The error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E30 (No Audio/Video) / 0132
Binary/Hex: 00011110 / 0x1E -> 30Known fixes:
No Known fixes available!
Description:
The error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E31 (No Audio/Video) / 0133
Binary/Hex: 00011111 / 0x1F -> 31Known fixes:
No Known fixes available!
Description:
The error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E32 (No Audio/Video) / 0200
Binary/Hex: 00100000 / 0x20 -> 32Known fixes:
1) Reflow the GPU/RAM
— For better results blow under the chips and flush them with alcohol if you can (clhdrums87)
2) X-Clamp FixDescription:
This error is caused by a Cold Joint in the GPU/RAM area similiar to 0102 good results could be achieved with flushing alcohol under the chips, reflowing them and afterwards applying an X-Clamp Fix.
_____________________________________________________
E-Code / Secondary Error code: E33 (No Audio/Video) / 0201
Binary/Hex: 00100001 / 0x21 -> 33Known fixes:
No Known fixes available!
Related Errors:
0102
Description:
The error is very rare but it is somehow GPU/RAM related, two people could fix it with the Improved X-Clamp replacement, one had to remove his washers from the RAM in order to get it to work.
Check the references for more information._____________________________________________________
E-Code / Secondary Error code: E34 (No Audio/Video) / 0202
Binary/Hex: 00100010 / 0x22 -> 34Known fixes:
No Known fixes available!
Description:
The error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E35 (No Audio/Video) / 0203
Binary/Hex: 00100011 / 0x23 -> 35Known fixes:
No Known fixes available!
Description:
code 0203 — instant rrod everytime. chip malfunction, not gettin a connection to the board (not an overheating problem but a bad contact problem) mine turned out to be broken prongs in a corner on the gpu, missin 3 of them. didnt see this til i was comparing with another board. i believe these are mini resistors on the bottom side of the chip due to mistreatment
_____________________________________________________
E-Code / Secondary Error code: E36 (No Audio/Video) / 0210
Binary/Hex: 00100100 / 0x24 -> 36Known fixes:
No Known fixes available!
Description:
This error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E37 (No Audio/Video) / 0211
Binary/Hex: 00100101 / 0x25 -> 37Known fixes:
No Known fixes available!
Description:
This error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E38 (No Audio/Video) / 0212
Binary/Hex: 00100110 / 0x26 -> 38Known fixes:
No Known fixes available!
Description:
This error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E39 (No Audio/Video) / 0213
Binary/Hex: 00100111 / 0x27 -> 39Known fixes:
No Known fixes available!
Description:
This error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E40 (No Audio/Video) / 0220
Binary/Hex: 00101000 / 0x28 -> 40Known fixes:
No Known fixes available!
Description:
This error is unknown but is assumed to be caused by missing resistors, probably on GPU.
_____________________________________________________
E-Code / Secondary Error code: E41 (No Audio/Video) / 0221
Binary/Hex: 00101001 / 0x29 -> 41Known fixes:
No Known fixes available!
Description:
This error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E42 (No Audio/Video) / 0222
Binary/Hex: 00101010 / 0x2A -> 42Known fixes:
1) X-Clamp replacement
Description:
This error is unknown but someone managed to fix it using the X-Clamp replacement.
_____________________________________________________
E-Code / Secondary Error code: E43 (No Audio/Video) / 0223
Binary/Hex: 00101011 / 0x2B -> 43Known fixes:
No Known fixes available!
Description:
This error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E44 (No Audio/Video) / 0230
Binary/Hex: 00101100 / 0x2C -> 44Known fixes:
No Known fixes available!
Description:
This error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E45 (No Audio/Video) / 0231
Binary/Hex: 00101101 / 0x2D -> 45Known fixes:
No Known fixes available!
Description:
This error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E46 (No Audio/Video) / 0232
Binary/Hex: 00101110 / 0x2E -> 46Known fixes:
It cant happen anymore since of new update.(Unconfirmed)
Description:
«The CD Drive overheats. This error can be caused by the disconnecting of the CD Drive. This is usually not the case.»(Unconfirmed)
_____________________________________________________
E-Code / Secondary Error code: E47 (No Audio/Video) / 0233
Binary/Hex: 00101111 / 0x2F -> 47Known fixes:
No Known fixes available!
Description:
This error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E56 (No Audio/Video) / 0320
Binary/Hex: 00111000 / 0x38 -> 56Known fixes:
No Known fixes available!
Description:
This error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E57 (No Audio/Video) / 0321
Binary/Hex: 00111001 / 0x39 -> 57Known fixes:
No Known fixes available!
Description:
This error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E58 (No Audio/Video) / 0322
Binary/Hex: 00111010 / 0x3A -> 58Known fixes:
No Known fixes available!
Description:
This error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E59 (No Audio/Video) / 0323
Binary/Hex: 00111011 / 0x3B -> 59Known fixes:
No Known fixes available!
Description:
This error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E60 (No Audio/Video) / 0330
Binary/Hex: 00111100 / 0x3C -> 60Known fixes:
No Known fixes available!
Description:
This error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E61 (No Audio/Video) / 0331
Binary/Hex: 00111101 / 0x3D -> 61Known fixes:
No Known fixes available!
Description:
This error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E62 (No Audio/Video) / 0332
Binary/Hex: 00111110 / 0x3E -> 62Known fixes:
No Known fixes available!
Description:
This error is completely unknown
_____________________________________________________
E-Code / Secondary Error code: E63 (No Audio/Video) / 0333
Binary/Hex: 00111111 / 0x3F -> 63Known fixes:
No Known fixes available!
Description:
This error is completely unknown
_____________________________________________________
4 RLOD Error codes
E-Code / Secondary Error code: — (No Audio/Video) / 4444
Binary/Hex: 00000000 / 0x00 -> 0Known fixes:
1) Try a different A/V cable and plug it in if yours is not working.
2) Reflow the A/V connector if it became loose
3) Reflowing the HANA chipDescription:
This error occurs when an A/V cable isnt plugged in or is faulty so make sure that it is working.Otherwise it might be a problem with the A/V connector(probably it became loose) or a cold solder joint under the (H)ANA chip.
Log in or Sign up
-
This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.
xbox rrod error 1021
Discussion in ‘Xbox 360 — Modding & Hacking’ started by eggman14, Apr 10, 2009.
-
eggman14
Regular member- Joined:
- Jun 12, 2008
- Messages:
- 198
- Likes Received:
- 0
- Trophy Points:
- 26
hello,
my xbox arcade has come up with the magic red ring of death.
i have bought a replacement but am really interested in finding out what actually is wrong.im a bit of a noob to modding but managed to flash ok and xclamps fix a few machines this one included.
it first went wrong directly after flashing iextreme 1.51 onto the benq vad6038 and came round briefly after i reapplied new thermal paste which had dried out.then it gave me error e74 twice and then e73 with 1021 as the secondary error code.some people say re flowing works which i’ve done to no avail and others refer to the ethernet port which i have inspected loosely but dont beleive its that as it hasnt been used.
i have tried running without the dvd drive,without the hdd(which is modded) and now i’ve ran out of idea’s.
any pointers are welcome.thanks
eggman14,
Apr 10, 2009
#1 -
gameover9
Guestread the RROD ultimate sticky
gameover9,
Apr 10, 2009
#2 -
slayer700
Member- Joined:
- Jul 7, 2008
- Messages:
- 45
- Likes Received:
- 0
- Trophy Points:
- 16
I believe that you might have put too much thermal compound…Just a thought
slayer700,
Apr 10, 2009
#3 -
eggman14
Regular member- Joined:
- Jun 12, 2008
- Messages:
- 198
- Likes Received:
- 0
- Trophy Points:
- 26
it could be possible i will give it a try.
cheers.i will post how i got on.
eggman14,
Apr 11, 2009
#4
(You must log in or sign up to reply here.)
Share This Page
- Log in with Facebook
- Log in with Twitter
- Log in with Google
- Your name or email address:
- Do you already have an account?
-
- No, create an account now.
- Yes, my password is:
-
Forgot your password?
-
Stay logged in
Search
-
- Search titles only
- Posted by Member:
-
Separate names with a comma.
- Newer Than:
-
- Search this thread only
- Search this forum only
- Display results as threads
-
Useful Searches
- Recent Posts
More…