093 314 ошибка xerox

7 Problem Solving

Error Code

091-313

[Cause]

[Remedy] Switch off the machine power, make sure that the touch screen is blank, and then

091-320

[Cause]

[Remedy] Switch off the machine power, make sure that the touch screen is blank, and then

091-407

[Cause]

[Remedy] Pull out the drum cartridge [R1], and then insert the cartridge again.

091-417

[Cause]

[Remedy] Pull out the drum cartridge [R4], and then insert the cartridge again.

091-427

[Cause]

[Remedy] Pull out the drum cartridge [R3], and then insert the cartridge again.

091-437

[Cause]

[Remedy] Pull out the drum cartridge [R2], and then insert the cartridge again.

093-313

[Cause]

[Remedy] Switch off the machine power, make sure that the touch screen is blank, and then

093-314

[Cause]

[Remedy] Switch off the machine power, make sure that the touch screen is blank, and then

093-315

093-316

093-317

7

093-320

[Cause]

[Remedy] Switch off the machine power, make sure that the touch screen is blank, and then

093-329

[Cause]

[Remedy] Replace with a new toner cartridge. Then switch off the machine power, make

093-401

[Cause]

[Remedy] Insert toner cartridge [Y] (yellow).

093-403

[Cause]

[Remedy] Insert toner cartridge [M] (magenta).

093-404

[Cause]

[Remedy] Insert toner cartridge [C] (cyan).

093-410

[Cause]

[Remedy] Insert toner cartridge [K] (black).

093-426

[Cause]

[Remedy] Pull out the toner cartridge [K] (black), and then insert the cartridge again.

093-427

[Cause]

[Remedy] Pull out the toner cartridge [Y] (yellow), and then insert the cartridge again.

093-428

[Cause]

[Remedy] Pull out the toner cartridge [M] (magenta), and then insert the cartridge again.

* If you cannot resolve an error despite following the instructions described in the table, contact your local Fuji Xerox

representative. The contact number is printed on the label or card attached on the machine.

210

Cause and Remedy

An error occurred.

switch on the machine power. If the same message is displayed again, contact

your local Fuji Xerox representative.

An error occurred.

switch on the machine power. If the error still is not resolved, contact your local

Fuji Xerox representative.

An error occurred in the drum cartridge [R1].

An error occurred in the drum cartridge [R4].

An error occurred in the drum cartridge [R3].

An error occurred in the drum cartridge [R2].

An error occurred.

switch on the machine power. If the error still is not resolved, contact your local

Fuji Xerox representative.

An error occurred.

switch on the machine power. If the same message is displayed again, contact

your local Fuji Xerox representative.

An error occurred.

switch on the machine power. If the error still is not resolved, contact your local

Fuji Xerox representative.

There was an abnormality with the toner cartridge.

sure that the touch screen is blank, and switch on the machine power again.

Toner cartridge [Y] (yellow) is not installed.

Toner cartridge [M] (magenta) is not installed.

Toner cartridge [C] (cyan) is not installed.

Toner cartridge [K] (black) is not installed.

An error occurred in the toner cartridge [K] (black).

An error occurred in the toner cartridge [Y] (yellow).

An error occurred in the toner cartridge [M] (magenta).

Xerox Phaser 5335: Сообщения об ошибках и коды ошибок.

Сообщения об ошибках и коды ошибок.

В принтере возникло застревание бумаги.
Выдвиньте наружу лоток 2 для поиска зоны застревания, и вытащите
Застрявшую бумагу. Затем откройте и закройте переднюю крышку. Откройте
Переднюю крышку, даже если под крышкой нет застрявшей бумаги. Ошибка на
Дисплее не сбросится, пока вы не откроете и не закроете переднюю крышку.

Откройте л.2 и 3
Устраните застр.

В принтере возникло застревание бумаги.
Выдвиньте наружу лоток 2 и лоток 3 для поиска зоны застревания, и вытащите
Застрявшую бумагу. Затем откройте и закройте переднюю крышку. Откройте
Переднюю крышку, даже если под крышкой нет застрявшей бумаги. Ошибка на
Дисплее не сбросится, пока вы не откроете и не закроете переднюю крышку.

Откройте лоток 4,3
& 2. Устраните застр.

В принтере возникло застревание бумаги.
Выдвиньте наружу лоток 2, лоток 3 и лоток 4 для поиска зоны застревания, и
Вытащите застрявшую бумагу. Затем откройте и закройте переднюю крышку.
Откройте переднюю крышку, даже если под крышкой нет застрявшей бумаги.
Ошибка на дисплее не сбросится, пока вы не откроете и не закроете переднюю
Крышку.

Нажмите SET
И отмените зад.

Задание нельзя распечатать, так как объем памяти недостаточный.
Отмените задание печати нажатием кнопки

Панели управления.
Уменьшите число файлов для печати и попробуйте распечатать еще раз. Если
Опять появится это сообщение, то мы советуем установить дополнительную
Память.

Нажмите SET
И отмените зад.

При обработке задания возникла ошибка.
Отмените задание печати нажатием кнопки

Панели управления.
Проверьте, нет ли проблемы с данными для печати.

Задание запросило лоток бумаги, но открыт один из лотков выше его.
Закройте открытый лоток

Открыт лоток N.
Задвиньте лоток в принтер до упора.

Один из лотков открыт в процессе печати.
Задвиньте лоток в принтер до упора.

Готов к печати
Набор обслуж.

Готов к печати
Скоро замена

Вскоре необходимо заменить ремонтный комплект (регулярно заменяемые
Детали). У вас должен быть новый комплект обслуживания (ремонтный).

Готов к печати
Картридж с тон.

Готов к печати
Скоро замена

Вскоре необходимо заменить принт-картридж. У вас должен быть новый
Картридж.

Это отказ принтера.
Выключите питание, подождите погасания дисплея, и затем снова включите
Питание принтера. Если опять отображается этот код ошибки, запишите
Его (***-***) и обращайтесь в ваш сервисный центр или к вашему дилеру.

Признак/Причина/Устранение

Устранение неисправностей ЗаменаКартридж с тон. В принт.

6 Устранение неисправностей

Замена
Картридж с тон.

В принт-картридже закончился тонер.
Замените принт-картридж.

Загр. лоток N
Xx xx xxxx

Формат загруженной в лоток N бумаги не соответствует формату, указанному
Для задания.
Загрузите указанную в сообщении бумагу (xx xx xxxx) в лоток N.

Произошла системная ошибка.
Выключите питание, подождите погасания дисплея, и затем снова
Включите питание принтера. Если опять отображается этот код ошибки,
Запишите его (***-***) и обращайтесь в ваш сервисный центр или к вашему
Дилеру.

Нажмите SET
И отмените зад.

Бал запрошен Автовыбор лотка при настройке [Приоритет бумаги] в [Выкл].
Отмените задание печати нажатием кнопки

Панели управления.
Настройте порядок приоритета для лотков или вручную выберите лоток с
Панели управления.

Неверный формат
Бумагу в обходн.

Формат загруженной в лоток 1 (обходной) бумаги не соответствует формату
Бумаги, настроенному в драйвере принтера или с панели управления.
Загрузите бумагу с форматом, указанным в драйвере принетра или с панели
Управления.

Неверный формат
Бумагу в лоток N

Формат бумаги, загруженной в лоток N, не соответствует формату,
Настроенному на шкале формата бумаги лотка.
Выдвиньте наружу лоток N, проверьте формат бумагу и настройку шкалы лотка
И вставьте лоток в принтер.

Признак/Причина/Устранение

Коды ошибок

6.6 Сообщения об ошибках и коды ошибок

В следующей таблице перечислены коды ошибок, которые могут быть устранены
Пользователем. Если отображается код ошибки, то проверьте, нет ли его в
Следующей таблице.
Следующие коды ошибок перечислены в возрастающем порядке.

Причина/Устранение

Блок термического закрепления тонера (фьюзер) может быть установлен неправильно или
Неисправен.
Выключите принтер и откройте переднюю крышку, потянув на себя рычаги освобождения
Передней крышки («А»).. Проверьте, что рычаги с обеих сторон блока закрепление тонера
Надежно зафиксированы, и затем включите питание принтера.

Если снова показан этот же код ошибки, то обращайтесь в ваш сервисный центр или к
Вашему дилеру.

Податчик листов (опцонный) неправильно установлен в принтере. Выключите питание
Принтера, проверьте, что податчик листов правильно установлен в принтере, и затем снова
Включите питание.

Руководство по установке податчика на 550 листов

Устранение неисправностей.

6 Устранение неисправностей

Блок двусторонней печати (опцонный) неправильно вставлен в принтер. Выключите
Питание принтера, проверьте, что соединитель кабеля блока двусторонней печати
Правильно подключен к принтеру, и затем снова включите питание.

Руководство по установке блока двусторонней печати’

Причина/Устранение

7 проблемы, относящиеся к сети, Проблемы служб centreware internet services

6.7 Проблемы, относящиеся к сети

Проблемы, относящиеся к сети

Информация по устранению связанных с сетью проблем печати приведена на
Компакт-диске с документацией.
Ниже перечислены проблемы, которые могут возникнуть при использовании
CentreWare Internet Services, печати по электронной почте и StatusMessenger. Если
Показано сообщение об ошибке или код ошибки, для её устранения перейдите к
Разделу «6.6 Сообщения об ошибках и коды ошибок» (стр. 129).

Проблемы служб CentreWare Internet Services

Причина/Устранение

Текст введен в поле ввода без
Превышения отведенных для
Ввода числа байтов (при этом
Каждый специальный символ
Считается за 2 байта), но весь
Текст не сохранился.

Принтер использует код Unicode UTF-8 для сохранения символов, введенных в
CentreWare Internet Services. Обычно в UTF-8 требуется от 2 до 4 байтов для
Сохранения одного специального символа (не буквенноцифрового).
Введенный вами текст мог превысить максимальное число байтов, отведенное
Для поля ввода, и поэтому не был сохранен.

Нет доступа к CentreWare
Internet Services.

Нормально ли работает принтер?
Проверьте, включен ли принтер.

Запущена ли служба Internet Services?
Распечатайте список [Настр. принтера] чтобы проверить, включены ли службы
Internet Services.

Правильно ли введен адрес URL?
Проверьте URL. Если вы все равно не можете получить доступа к службе, то
Введите IP-адрес принтера вместо URL.

Правильно ли настроен номер порта HTTP?
Еще раз проверьте номер порта HTTP. Если вы изменили номер порта, нужно
Ввести «:» (двоеточие) и затем номер порта после адреса при доступе к
CentreWare Internet Services.
Пример) https://printer1.example. com:80/

Если включена связь с сервером по SSL/TLS, то правильно ли вы ввели адрес в
Адресное поле?
Если разрешена связь с сервером по протоколу SSL/TLS, то введите «https»
Перед адресом вместо «http». Кроме того, если вы изменили номер порта
SSL/TLS, то введите «:» (двоеточие) перед номером порта.

Использует ли ваш обозреватель Интернет прокси-сервер?
CentreWare Internet Services могут быть недоступны в зависимости от
Используемого прокси-сервера.
Попытайтесь вызвать службы без прокси-сервера.

См. • Оперативная справочная система вашего обозревателя Интернет

В обозреватели Интернет
Выводится сообщение
«Подождите. » и оно не
Исчезает.

Немного подождите, как указано.
Если ничего не меняется, то обновите экран обозревателя. Если это не
Помогает, то проверьте, нормально ли работает принтер.

Не отображается самая
Последняя информация.

Устранение неисправностей Кнопка.

6 Устранение неисправностей

Кнопка [Обновить] не работает.
Содержимое правой рамки не
Меняется, даже если в левой
Рамке выбрана другая тема.
Служба работает медленно.

Поддерживаются ли ваша операционная система и обозреватель Интернет
Службой CentreWare Internet Services?
Список поддерживаемых службой операционных систем и веб-браузеров
Приведен в разделе «1.5 Конфигурирование принтера с помощью служб
CentreWare Internet Services» (стр. 13).

Если ваш обозреватель использует прокси-сервер, то окно может обновляться
Неправильно или замедлить работу.
Попытайтесь вызвать службы CentreWare Internet Services без прокси-сервера.

Старая информация может кэшироваться вашим обозревателем Интернет.
Сотрите всю информацию в кэше обозревателя.

Отображаемая на экране
Информация искажена.

Измените размер окна или настройку размера шрифта в обозревателе
Интернет.

Нажатие [Применить] не
Показывает новых настроек.

Правильно ли вы ввели значения?
Если величины недопустимы, то будет показано сообщение об ошибке.
Проверьте, что все значения введены правильно.

Забыт ИД или пароль
Системного администратора и
Нельзя изменить настройки.

Если вы не можете вспомнить ИД и пароль, Инициализируйте настройки в
Пункте [Иниц/удал данные] > [Иниц/сетев. порт] на панели управления. Однако
Эта операция сбросит в значения по умолчанию все относящиеся к сети
Настройки. Перед инициализацией настроек рекомендуется записать текущие
Настройки, распечатав для этого список [Настр. принтера].

Служба не принимает ИД или
Пароля пользователя.

Если у вас возникнет ошибка входа четыре раза подряд после включения
Питания или после последнего успешного входа, то ваш доступ к службе будет
Заблокирован. В зависимости от используемого обозревателя Интернет окно
Входа может не закрываться, пока вы не отмените попытку входа.
В таком случае перезагрузите принтер и попробуйте войти в него еще раз.

Язык дисплея отличается от
Нужного вам.

Измените настройку языка дисплея в вашем обозревателе Интернет.

См. • Оперативная справочная система вашего обозревателя Интернет

Если вы одновременно ведете доступ к принтеру из нескольких обозревателей
Интернет и StatusMessenger с разными языками, то полученная от принтера
Строчка символов может отличаться от настройки языка в вашем обозревателе.
В этом случае обновите экран обозревателя Интернет.

Такая проблема может также возникнуть, если ваш обозреватель использует
Прокси-сервер.
Попытайтесь вызвать службы без прокси-сервера.

См. • Оперативная справочная система вашего обозревателя Интернет

Подключение к CentreWare
Internet Services было
Отменено, или выведено
Сообщение «Страница не
Содержит данных».

Это может случиться, если вы слишком часто обновляете окно обозревателя
Интернет. Старайтесь не обновлять окно обозревателя слишком часто.
Также, не оставляйте вкладки [Состояние] или [Задания] открытыми в
Нескольких обозревателях.

Кнопки отображаются как
Ссылки URL.

Некоторые кнопки службы используют JavaScript. Такие кнопки не
Отображаются, если JavaScript не работает или выключен. В таком случае
Кнопки отображаются как ссылки URL.
Мы рекомендуем включить JavaScript в вашем обозревателе Интернет.

Источники:

Https://manualza. ru/xerox/phaser-5335/bbja151

     Во время работы с аппаратом могут возникать проблемы, связанные с неисправностями «железа» или ПО. И если расходные материалы можно просто заменить, то с «мозгами» нужно разбираться. Поэтому, для экономии времени и удобства, ниже представлены возможные коды ошибок (FAULT ERROR CODE), которые показывают Xerox DocuColor DC 240/250/242/252/260 и WorkCentre WC 7655/7665/7675/7755/7765/7775 при неисправности, и их значение:

коды ошибок (fault code/error) продолжение. Часть 2

     …

 061-323 ERROR — RAP No SOS Failure.

 061-324 ERROR — RAP No SOS Failure.

 061-325 ERROR — RAP No SOS Failure.

 061-326 ERROR — RAP ROS Connect Failure Yellow.

 061-327 ERROR — RAP ROS Connect Failure.

 061-328 ERROR — RAP ROS Connect Failure.

 061-329 ERROR — RAP ROS Connect Failure Black.

 061-334 ERROR — RAP ROS Y/M VDD Failure.

 061-335 ERROR — RAP ROS C/K VDD Failure.

 061-336 ERROR — RAP ROS Y/M VDD Down Failure.

 061-337 ERROR — RAP ROS C/K VDD Down Failure.

 061-338 ERROR — RAP SOS Stop Magenta Failure.

 061-339 ERROR — RAP SOS Stop Black Failure.

 061-340 ERROR — RAP ROS LD Failure Black.

 061-341 ERROR — RAP ROS LD Failure Yellow.

 061-342 ERROR — RAP ROS LD Failure Magenta.

 061-343 ERROR — RAP ROS LD Failure Cyan.

 061-600 ERROR — RAP ROS Data Failure Yellow.

 061-601 ERROR — RAP ROS Data Failure Magenta.

 061-602 ERROR — RAP ROS Data Failure Cyan.

 061-603 ERROR — RAP ROS Data Failure Black.

 061-604 ERROR — RAP LD Alarm Yellow.

 061-605 ERROR — RAP LD Alarm Magenta.

 061-606 ERROR — RAP LD Alarm Cyan.

 061-607 ERROR — RAP LD Alarm Black.

 062-210 ERROR — RAP IISS Hot Line Failure.

 062-211 ERROR — RAP IIT/IPS EEPROM Failure (IPS).

 062-220 ERROR — RAP IPS-EXT Connection Failure.

 062-277 ERROR — RAP IIT/IPS-DADF Communication Failure.

 062-278 ERROR — RAP IIT-Extension Communication Failure.

 062-300 ERROR — RAP Platen Interlock Open.

 062-310 ERROR — RAP IIT/IPS-ESS Communication Failure.

 062-311 ERROR — RAP IIT Software Logic Failure.

 062-321 ERROR — RAP IPS-YATA Connection Failure.

 062-322 ERROR — RAP EXT-YATA Connection Failure.

 062-323 ERROR — RAP YATA PWBA Failure.

 062-345 ERROR — RAP IIT/IPS EEPROM Failure (IIT).

 062-355 ERROR — RAP IPS Fan Failure.

 062-356 ERROR — RAP Lamp Fan Failure.

 062-357 ERROR — RAP CCD Fan Failure. An error signal was detected for the CCD fan.

 062-360 ERROR — RAP Carriage Position Failure.

 062-362 ERROR — RAP X Hard Failure.

 062-371 ERROR — RAP Lamp Failure.

 062-380 ERROR — RAP Platen AOC Failure.

 062-386 ERROR — RAP Platen AOC Failure.

 062-389 ERROR — RAP Carriage Over Run (Scan End).

 062-392 ERROR — RAP IT/IPS Memory Failure.

 062-393 ERROR — RAP IIT/IPS PWB Failure.

 062-790 ERROR — RAP X Detect Failure.

 063-210 ERROR — RAP Extension EEPROM Failure.

 063-220 ERROR — RAP IPS-EXT Psync Failure.

 063-230 ERROR — RAP EXT Image Parameter Failure.

 063-240 ERROR — RAP EXT Image Parameter Failure.

 065-210 ERROR — RAP Extension Page Memory Failure 1.

 065-211 ERROR — RAP CIS Shading FROM Failure

 065-212 ERROR — RAP CIS Shading Level Failure.

 065-213 ERROR — RAP CIS Output Level Failure.

 065-215 ERROR — RAP Extension Page Memory Failure 2.

 065-216 ERROR — RAP Extension Page Memory Failure 3.

 065-219 ERROR — RAP CIS Black White Level Failure.

 065-220 ERROR — RAP 1P DUP PWB-EXT Psync Failure.

 071-101 ERROR — RAP Feed Out Sensor 1 is not turned ON.

 071-104 ERROR — RAP Pre Registration Sensor ON Jam (Tray 1).

 071-105 ERROR — RAP Registration Sensor ON Jam (Tray 1).

 071-210 ERROR — RAP Tray 1 Lift Up Failure.

 072-101 ERROR — RAP Tray 2 Miss Feed Jam.

 072-102 ERROR — RAP The Tray 1 Feed Out Sensor does not turn ON.

 072-104 ERROR — RAP Pre-Registration Sensor ON Jam (Tray 2).

 072-105 ERROR — RAP Registration Sensor ON Jam (Tray 2).

 072-210 ERROR — RAP Tray 2 Lift Up Failure.

 073-101 ERROR — RAP Tray 3 Miss Feed Jam.

 073-102 ERROR — RAP Feed Out Sensor 1 ON Jam (Tray 3).

 073-104 ERROR — RAP Pre Registration Sensor ON Jam (Tray 3).

 073-105 ERROR — RAP Registration Sensor ON Jam (Tray 3).

 073-210 ERROR — RAP Tray 3 Lift Up Failure.

 074-101 ERROR — RAP Pre Feed Sensor 4 is not ON within the specified time after the start of feed from Tray 4.

 074-102 ERROR — RAP Feed Out Sensor 1 ON Jam (Tray 4).

 074-103 ERROR — RAP The Tray 4 Feed Out Sensor is not ON within the specified time for paper fed from Tray 4.

 074-104 ERROR — RAP Pre Registration Sensor ON Jam (Tray 4).

 074-105 ERROR — RAP Registration Sensor ON Jam (Tray 4).

 074-210 ERROR — RAP Tray 4 Lift Up Failure.

 075-100 ERROR — RAP Tray 5/Bypass Pre Feed Sensor is not ON within the specified time after the start of feed from Tray 5.

 075-101 ERROR — RAP Tray 5/Bypass Feed Out Sensor is not ON within the specified time for paper fed from Tray 5.

 075-109 ERROR — RAP Paper from Tray 5/Bypass does not turn ON Pre Regi Sensor within a specified time.

 075-135 ERROR — RAP Paper from Tray 5/Bypass does not turn ON Regi Sensor within a specified time.

 075-210 ERROR — RAP Tray 5/Bypass Lift Up Sensor does not turn ON within a specified time after Tray 5 begins to lift.

 075-211 ERROR — RAP Tray 5/Bypass Lift Down Sensor does not turn ON within a specified time after Tray 5 begins to lower.

 077-102 ERROR — RAP Paper from Tray 2 did not turn on the Transport Path Sensor 1 within the specified time.

 077-103 ERROR — RAP The Fuser Exit Sensor did not turn off within the specified time in straight exit mode.

 077-106 ERROR — RAP The Fuser Exit Sensor did not come on within the specified time after the Registration Motor.

 077-107 ERROR — RAP The Fuser Exit Sensor did not turn off within the specified time in invert exit mode.

 077-109 ERROR — RAP The IOT Exit Sensor did not come on at the specified time in non-invert mode.

 077-111 ERROR — RAP The IOT Exit Sensor did not come on within the specified time in invert exit mode.

 077-113 ERROR — RAP The IOT Exit Sensor did not turn off at the specified time in non-invert mode.

 077-115 ERROR — RAP The IOT Exit Sensor did not turn off within the specified time in invert exit mode.

 077-118 ERROR — RAP Paper from Duplex did not turn on the Pre Regi Sensor within the specified time.

 077-120 ERROR — RAP Post 2nd BTR Sensor On JAM.

 077-123 ERROR — RAP Duplex In Sensor does not turn ON a spec time after the start of invert.

 077-129 ERROR — RAP Paper from Duplex did not turn on the Regi Sensor within the specified time.

 077-130 ERROR — RAP Duplex Out Sensor does not turn ON witin a specified time after Duplex In Sensor turns ON.

 077-300 ERROR — RAP The Front Cover is open.

 077-301 ERROR — RAP The Left Hand Interlock is open.

 077-302 ERROR — RAP The Right Hand Cover Interlock is open.

 077-303 ERROR — RAP PH Drawer Interlock Open.

 077-304 ERROR — RAP The Tray 5/Bypass Cover Interlock is open.

 077-312 ERROR — RAP Feeder Communication Failure.

 077-909 ERROR — RAP One of the IOT sensors detected paper when power was turned on or when an interlock was closed.

 077-967 ERROR — RAP The specified paper type and the paper type being used are different.

 077-968 ERROR — RAP The type of paper in the tray was changed.

 078-100 ERROR — RAP Paper from Tray 6 does not turn ON Pre Regi Sensor within a specified time.

 078-101 ERROR — RAP The Tray 6 Feed Out sensor is not ON within the specified time for paper fed from Tray 6.

 078-102 ERROR — RAP Paper from Tray 6 does not turn ON the Regi Sensor within a specified time.

 078-151 ERROR — RAP The Tray 6 Feed Out Sensor did not come on within the specified time after the start of feed.

 078-250 ERROR — RAP HCF Tray #2 Lift Up Fail.

 078-300 ERROR — RAP The HCF transport interlock is open.

 078-301 ERROR — RAP HCF Side Out Interlock Open.

 089-600 ERROR — RAP Incorrect Fast Scan positioning for the reference color Cyan was detected during fine adjustment.

 089-601 ERROR — RAP The Inner MOB Sensor failed to detect the fine-adjustment patterns properly during fine adjustment.

 089-602 ERROR — RAP The CENTER MOB Sensor failed to detect the fine-adjustment patterns properly during fine adjustment.

 089-603 ERROR — RAP The OUTER MOB Sensor failed to detect the fine-adjustment patterns properly during fine adjustment.

 089-604 ERROR — RAP The INNER MOB Sensor failed to detect the rough-adjustment patterns properly during Yellow rough adjustment.

 089-605 ERROR — RAP The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Yellow rough adjustment.

 089-606 ERROR — RAP The OUTER MOB Sensor failed to detect the rough-adjustment patterns properly during Yellow rough adjustment.

 089-607 ERROR — RAP The INNER MOB Sensor failed to detect the rough-adjustment patterns correctly during Magenta rough adjustment.

 089-608 ERROR — RAP The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Magenta rough adjustment.

 089-609 ERROR — RAP The OUTER MOB Sensor failed to detect the rough-adjustment patterns properly during Magenta rough adjustment.

 089-610 ERROR — RAP The INNER MOB Sensor failed to detect the rough-adjustment patterns properly during Cyan rough adjustment.

 089-611 ERROR — RAP The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Cyan rough adjustment.

 089-612 ERROR — RAP The MOB Sensor OUT failed to detect the rough-adjustment patterns properly during Cyan rough adjustment.

 089-613 ERROR — RAP The INNER MOB Sensor failed to detect the rough-adjustment patterns properly during Black rough adjustment.

 089-614 ERROR — RAP The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Black rough adjustment.

 089-615 ERROR — RAP The MOB Sensor OUT failed to detect the rough-adjustment patterns properly during Black rough adjustment.

 089-616 ERROR — RAP RC Data OverFlow Failure.

 089-617 ERROR — RAP RC Data OverRange Failure.

 091-311 ERROR — RAP The voltage level of the CC cleaner position sensor did not change within the specified time.

 091-312 ERROR — RAP Charge (K) Preclean HVPS has failed.

 091-313 ERROR — RAP DRUM CRUM ASIC Communication Failure.

 091-320 ERROR — RAP Charge Corotron Wire is broken.

 091-400 ERROR — RAP The replacement date for Waste Toner Bottle (regular) is near.

 091-401 ERROR — RAP The black drum cartridge is near the end-of-life.

 091-403 ERROR — RAP The CC Assembly is near the end-of-life.

 091-404 ERROR — RAP The CC Assembly has reached the end-of-life.

 091-411 ERROR — RAP The yellow drum cartridge is near the end-of-life.

 091-421 ERROR — RAP The magenta drum cartridge is near the end-of-life.

 091-431 ERROR — RAP The cyan drum cartridge is near the end-of-life.

 091-910 ERROR — RAP The waste toner bottle is not present.

 091-911 ERROR — RAP The waste toner bottle is full.

 091-913 ERROR — RAP The black drum cartridge (K) has reached the end-of-life.

 091-914 ERROR — RAP Communication failure between the MCU and the black Drum CRUM.

 091-915 ERROR — RAP The MCU detected incorrect data in the black drum cartridge CRUM.

 091-916 ERROR — RAP The CRUM authentication registration data on the drum cartridge is incorrect.

 091-917 ERROR — RAP MCU cannot communicate with the CRUM in drum Y.

 091-918 ERROR — RAP Communication failure with the magenta Drum CRUM.

 091-919 ERROR — RAP Communication failure with the cyan Drum CRUM.

 091-920 ERROR — RAP The MCU detected incorrect data in the Yellow drum cartridge CRUM.

 091-921 ERROR — RAP Drum CRUM is disconnected.

 091-922 ERROR — RAP Wrong Data in magenta drum cartridge.

 091-923 ERROR — RAP Wrong data in cyan drum cartridge.

 091-924 ERROR — RAP The CRUM authentication registration data on the yellow drum cartridge is incorrect.

 091-925 ERROR — RAP Wrong data in yellow Magenta cartridge.

 091-926 ERROR — RAP The CRUM authentication registration data on the cyan drum cartridge is incorrect.

 091-927 ERROR — RAP Yellow Drum CRUM is disconnected.

 091-928 ERROR — RAP Magenta Drum CRUM is disconnected.

 091-929 ERROR — RAP Cyan Drum CRUM is disconnected.

 091-932 ERROR — RAP The yellow drum cartridge (Y) has reached the end-of-life.

 091-933 ERROR — RAP The magenta drum cartridge (M) has reached the end-of-life.

 091-934 ERROR — RAP The cyan drum cartridge (C) has reached the end-of-life.

 092-649 ERROR — RAP The MOB ADC Shutter remains open due to shutter failure.

 092-650 ERROR — RAP The MOB ADC Shutter remains closed due to shutter failure.

 092-651 ERROR — RAP The output read by ADC Sensor from the clean Photoreceptor surface is out of range.

 092-652 ERROR — RAP The measured ADC Patch density is light. (Over 75% of Vclean).

 092-653 ERROR — RAP ATC SNR-Yellow output signal failure.

 092-654 ERROR — RAP ATC SNR-Magenta output signal failure.

 092-655 ERROR — RAP ATC SNR-Cyan output signal failure.

 092-656 ERROR — RAP ATC SNR-black output signal failure.

 092-657 ERROR — RAP The amplitude of ATC Yellow Sensor output is out of range.

 092-658 ERROR — RAP The amplitude of ATC Magenta Sensor output is out of range.

 092-659 ERROR — RAP The amplitude of ATC Cyan Sensor output is out of range.

 092-660 ERROR — RAP The amplitude of ATC Black Sensor output is out of range.

 092-661 ERROR — RAP The temperature output of the environment sensor is out of range.

 092-662 ERROR — RAP The humidity output of the environment sensor is out of range.

 092-663 ERROR — RAP The two levels of ADC Patch density created in Mini-Setup are reversed.

 093-300 ERROR — RAP Marking Drawer Interlock Open.

 093-313 ERROR — RAP The Low Toner Sensor failed to detect any toner after the Toner Cartridge Motor was energized.

 093-314 ERROR — RAP Yellow Dispense failure.

 093-315 ERROR — RAP Magenta Dispense failure.

 093-316 ERROR — RAP Cyan Dispense failure.

 093-317 ERROR — RAP Black Dispense failure.

 093-320 ERROR — RAP There was a problem with the developer motor rotation.

 093-421 ERROR — RAP The Black Toner Cartridge (K1) is empty and the Black Toner Cartridge (K2) is near empty.

 093-422 ERROR — RAP The Black Toner Cartridge (K2) is empty and the Black Toner Cartridge (K1) is near empty.

 093-423 ERROR — RAP Yellow toner is near empty.

 093-424 ERROR — RAP Magenta toner is near empty.

 093-425 ERROR — RAP Cyan toner empty.

 093-600 ERROR — RAP Yellow Dispense near failure.

 093-601 ERROR — RAP Magenta Dispense near failure.

 093-602 ERROR — RAP Cyan Dispense near failure.

 093-603 ERROR — RAP Black Dispense near failure.

 093-912 ERROR — RAP The Black Dispense Motor rotation timed out indicating that the Black Cartridge and Reserve Tank are empty.

 093-918 ERROR — RAP A communication failure with Black Toner Cartridge CRUM K2.

 093-924 ERROR — RAP A communication failure with Black Toner Cartridge CRUM K1.

 093-925 ERROR — RAP The data written to the toner CRUM K1 did not agree with the data read.

 093-926 ERROR — RAP Toner Cartridge CRUM K1 Authentication Data is different.

 093-927 ERROR — RAP A communication failure with Yellow Toner Cartridge CRUM Y.

 093-928 ERROR — RAP A communication failure with Magenta Toner Cartridge CRUM M.

 093-929 ERROR — RAP A communication failure with Cyan Toner Cartridge CRUM C.

 093-932 ERROR — RAP Cartridge Exchange Time Over.

 093-934 ERROR — RAP The data written to the toner CRUM M did not agree with the data read.

 093-935 ERROR — RAP The data written to the toner CRUM C did not agree with the data read.

 093-936 ERROR — RAP The data written to the toner CRUM K2 did not agree with the data read.

 093-937 ERROR — RAP Toner Cartridge CRUM Y Authentication Data is different.

 093-938 ERROR — RAP Toner Cartridge CRUM M Authentication Data is different.

 093-939 ERROR — RAP Toner Cartridge CRUM C Authentication Data is different.

 093-940 ERROR — RAP Toner Cartridge CRUM K2 Authentication Data is different.

 094-320 ERROR — RAP Retraction was not detected within the specified time after retraction of the 1st BTR started.

 094-321 ERROR — RAP First BTR Contact Failure.

 094-322 ERROR — RAP Second BTR Retract Failure.

 094-323 ERROR — RAP Contact was not detected within the specified time after contact with the 2nd BTR started.

 102-356 ERROR — RAP Fatal error related to the EWS.

 102-380 ERROR — RAP Fatal error in the MF UI count.

 102-381 ERROR — RAP ESS error during communication between ESS and the control panel.

 102-382 ERROR — RAP A verification message was not returned from the Control Panel within the specified time.

112-700 ERROR — RAP The punch dust box is full.

116-210 ERROR — RAP Media Reader Fatal Error.

116-211 ERROR — RAP Media Reader Cable disconnected.

116-212 ERROR — RAP [Media Reader] MediaLib SW Logic Failure.

116-310 ERROR — RAP An error was detected while checking ESS font ROM DIMM #1.

116-312 ERROR — RAP An error was detected in the HDD encryption key during activation.

116-313 ERROR — RAP An encryption key was specified but the HDD itself was not encrypted.

116-314 ERROR — RAP An ethernet error was detected.

116-315 ERROR — RAP An error was detected during System Memory 1 R/W.

116-316 ERROR — RAP An error was detected during System Memory 2 R/W.

116-317 ERROR — RAP An error was detected when checking the MF ROM.

116-318 ERROR — RAP An error was detected when checking the expansion ROM R2.

116-321 ERROR — RAP System Software Fatal Error.

116-322 ERROR — RAP WebDAV S/W Failure.

116-323 ERROR — RAP An error was detected during the ESS PWB NVM Read/Write Check.

116-324 ERROR — RAP A fatal software exception error has occurred in the Controller PWB CPU.

116-325 ERROR — RAP An error occurred in ESS fan rotation.

116-329 ERROR — RAP A system call error related to the serial I/F was detected.

116-330 ERROR — RAP Error during HDD check.

116-331 ERROR — RAP An error related to the log was detected.

116-332 ERROR — RAP An error in the MF ROM ( ) was detected.

116-333 ERROR — RAP A problem occurred during software processing, and processing could no longer continue.

116-336 ERROR — RAP Redirector HD Failure. A problem was detected during HD access.

116-337 ERROR — RAP Fatal error with SNTP in general.

116-338 ERROR — RAP Fatal error with JBA in general.

116-340 ERROR — RAP There was insufficient page memory, input buffers, or work area.

116-341 ERROR — RAP Incorrect version or invalid combination ROM DIMMs are installed.

116-342 ERROR — RAP Fatal error related to the SNMP agent.

116-343 ERROR — RAP An IC error within the ESS PWB was detected.

116-346 ERROR — RAP Formatter failure. Error return from a system call.

116-348 ERROR — RAP Redirector failure. Error return from a system call.

116-349 ERROR — RAP There was an error with a call within SIF related to Pflite.

116-350 ERROR — RAP Fatal error with AppleTalk in general.

116-351 ERROR — RAP Fatal error related to EtherTalk.

116-352 ERROR — RAP Fatal error related to NetWare.

116-353 ERROR — RAP A physical problem was detected with the HDD during activation, causing the HDD not to activate.

116-354 ERROR — RAP A problem with the HDD product code was detected during activation.

116-355 ERROR — RAP Fatal error related to the SNMP agent.

116-356 ERROR — RAP The HDD was formatted, but an HDD failure occurred.

116-357 ERROR — RAP PostScript fatal system error.

116-358 ERROR — RAP Fatal error related to the salutation.

116-359 ERROR — RAP Fatal error in PLW.

116-360 ERROR — RAP Fatal error related to SMB.

116-361 ERROR — RAP SPL HDD fatal error. SpoolCont detected an error during HDD access.

116-362 ERROR — RAP SSDP software failure.

116-363 ERROR — RAP BMLinkS or print service software failure.

116-364 ERROR — RAP A timer error was detected.

116-365 ERROR — RAP SPL fatal error.

116-366 ERROR — RAP Report generator incorrect operation.

116-367 ERROR — RAP Parallel fatal error.

116-368 ERROR — RAP DumpPrint fatal error.

116-370 ERROR — RAP XJCL fatal error.

116-371 ERROR — RAP PCL Decomposer Software Failure. PCL fatal error.

116-373 ERROR — RAP Fatal error related to Dynamic DNS.

116-374 ERROR — RAP AutoSW fatal error.

116-376 ERROR — RAP Port 9100 Software Fail.

116-378 ERROR — RAP Fatal error related to MCR.

116-379 ERROR — RAP Fatal error related to MCC.

116-380 ERROR — RAP An error was detected while checking ESS font ROM DIMM #1.

116-381 ERROR — RAP The ABL did not agree with the ABL version information in NVM, or the data was corrupted.

116-382 ERROR — RAP An ABL access to NVM or HDD failed.

116-385 ERROR — RAP Fatal error related to the IDC.

116-388 ERROR — RAP It was detected that no HD is installed.

116-389 ERROR — RAP The system detected that no additional RAM was installed.

116-390 ERROR — RAP A version mismatch was detected between the standard ROM and NVM.

116-391 ERROR — RAP Incorrect specification of the country code, territory code, or paper size group.

116-395 ERROR — RAP Fatal error related to the USB.

116-701 ERROR — RAP Duplex printing is not possible due to insufficient memory.

116-702 ERROR — RAP Printing occurred with a substitute font.

116-703 ERROR — RAP PostScript data problem during PostScript grammar interpretation or language interpretation.

116-704 ERROR — RAP MediaReader No Insert (No Job).

116-705 ERROR — RAP MediaReader Format Error (No Job).

116-706 ERROR — RAP MediaReader: File Attribute Read Error (No Job).

116-707 ERROR — RAP MediaReader: Image File Read Error (No Job).

116-708 ERROR — RAP MediaReader: File Attribute Read Error (In Job).

116-709 ERROR — RAP MediaReader: Image File Read Error (Occurs during job).

116-710 ERROR — RAP Original size not correctly determined.

116-711 ERROR — RAP Mismatch in size and direction or ART EX form with paper to be printed.

116-712 ERROR — RAP PLW form / logo data cannot be registered due to insufficient RAM or HD space.

116-713 ERROR — RAP The job was divided because the HDD was full.

116-714 ERROR — RAP An HP-GL/2 (option) command error occurred.

116-715 ERROR — RAP The form could not be registered because the ART EX form registration upper limit was reached.

116-716 ERROR — RAP MediaReader File Does Not Exist.

116-717 ERROR — RAP MediaLib: Not Execute of New Request.

116-718 ERROR — RAP The specified ART EX form has not been registered.

116-720 ERROR — RAP PCL Memory Low, Page Simplified.

116-737 ERROR — RAP User defined data could not be registered because there was insufficient ART IV user definition memory.

116-738 ERROR — RAP Synthesis problem due to the specified ART IV form size and direction were different from the paper size and direction.

116-739 ERROR — RAP Form / logo data could not be registered because there was insufficient ART IV memory or HDD capacity.

116-740 ERROR — RAP An error occurred because the print data exceeded the printer limit.

116-741 ERROR — RAP No more forms can be registered because the number of ART IV Forms registered has reached the upper limit.

116-742 ERROR — RAP No more logo data can be registered because the number of ART IV log data registered has reached the upper limit.

116-743 ERROR — RAP The form or logo data could not be registered due to insufficient ART IV memory.

116-745 ERROR — RAP An ART IV command error occurred.

116-746 ERROR — RAP The specified form has not been registered.

116-747 ERROR — RAP The paper margin value is too large for the HP-GL/2 (option) effective coordinate area.

116-748 ERROR — RAP The HP-GL/2 (option) print data does not contain any image data.

116-749 ERROR — RAP The specified PostScript font is not in ROM or HDD.

116-771 ERROR — RAP Invalid JBIG Parameter DL Fixed.

116-772 ERROR — RAP Invalid JBIG Parameter D Fixed.

116-773 ERROR — RAP Invalid JBIG Parameter P Fixed.

116-774 ERROR — RAP Invalid JBIG Parameter YD Fixed.

116-775 ERROR — RAP Invalid JBIG Parameter LO Fixed.

116-776 ERROR — RAP Invalid JBIG Parameter MX Fixed.

116-777 ERROR — RAP Invalid JBIG Parameter MY Fixed.

116-778 ERROR — RAP Invalid JBIG Parameter VLENGTH Fixed.

116-780 ERROR — RAP There was a problem with the document attached to the received mail.

116-790 ERROR — RAP Stapling was cancelled.

123-200 ERROR — RAP The data received from ESS exceeded the buffer size of the storage destination within the control panel.

123-201 ERROR — RAP Data intended to be received from the control panel exceeded the buffer size of the storage destination within the control panel.

123-202 ERROR — RAP Events occurred that exceeded the processing capability for requests generated within the control panel.

123-203 ERROR — RAP UI Debug code.

123-204 ERROR — RAP SIO Parameter Failure (UI-Control panel).

123-205 ERROR — RAP SIO Command Failure (UI-Control panel).

123-206 ERROR — RAP SIO Status Failure (UI-Control panel).

123-207 ERROR — RAP Comm Manager Target Failure (UI-Control panel).

123-208 ERROR — RAP Comm Manager Command Failure (UI-Control panel).

123-209 ERROR — RAP EVM Returns Wrong Value (UI-Control panel).

123-310 ERROR — RAP Send Queue Full (UI-Control panel).

123-311 ERROR — RAP Receive Queue Full (UI-Control panel).

123-312 ERROR — RAP EVM Uses Wrong API (UI-Control panel).

123-313 ERROR — RAP AS Uses Wrong API (UI-Control panel).

123-314 ERROR — RAP Event-Waiting Timer Timeout (UI-Control panel).

123-315 ERROR — RAP CTS Internal Failure (UI-Control panel).

123-316 ERROR — RAP Send Request Queue Full SIO (UI-Control panel).

123-317 ERROR — RAP Receive Message Queue Full (UI-Control panel).

123-318 ERROR — RAP Receive Finish Queue Full (UI-Control panel).

123-319 ERROR — RAP Send Failure with No ACK (UI-Control panel).

123-320 ERROR — RAP Polling Failure (UI-Control panel).

123-321 ERROR — RAP Send Message Failure (UI-Control panel).

123-322 ERROR — RAP Target Failure (UI-Control panel).

123-323 ERROR — RAP Address Failure (UI-Control panel). Serial communication error.

123-324 ERROR — RAP Size Failure (UI-Control panel). Serial communication error.

123-325 ERROR — RAP Object Creation Failure (UI-Control panel).

123-326 ERROR — RAP Memory Overflow (UI-Control panel).

123-327 ERROR — RAP Button Overflow (UI-Control panel).

123-328 ERROR — RAP UI Internal Failure with Out of Area.

123-329 ERROR — RAP UI Internal Failure with Invalid Coordinates.

123-330 ERROR — RAP Interface Failure with Invalid Parameter LCD.

123-331 ERROR — RAP UI Internal Failure with Invalid LED Request.

123-332 ERROR — RAP I/F Failure (Invalid Parameter CP).

123-333 ERROR — RAP I/F Failure (No Communication).

123-334 ERROR — RAP I/F Failure (Receiving Error Key Code).

123-335 ERROR — RAP I/F Failure (Receiving Invalid Coordinates).

123-336 ERROR — RAP I/F Failure (DM-ACD Drv. I/F).

123-337 ERROR — RAP Frame Data Error with Invalid Data Type.

123-338 ERROR — RAP Frame Data Error Offset Address Out.

123-339 ERROR — RAP Display Request Code Invalid.

123-340 ERROR — RAP Interface Failure GUAM-DM I/F.

123-341 ERROR — RAP Event Queue Full (UI-Control panel).

123-342 ERROR — RAP Event Queue Empty (UI-Control panel).

123-343 ERROR — RAP Invalid Class (UI-Control panel).

123-344 ERROR — RAP Invalid Type (UI-Control panel).

123-345 ERROR — RAP Timer Queue Full (UI-Control panel).

123-346 ERROR — RAP Invalid Timer Number (UI-Control panel).

123-347 ERROR — RAP Undefined Trap (UI-Control panel).

123-348 ERROR — RAP Command Access Exception (UI-Control panel).

123-349 ERROR — RAP Invalid Command (UI-Control panel).

123-350 ERROR — RAP Privilege Command (UI-Control panel).

123-351 ERROR — RAP No FPU Exception (UI-Control panel).

123-352 ERROR — RAP Address Mis-align (UI-Control panel).

123-353 ERROR — RAP Data Access Exception (UI-Control panel).

123-354 ERROR — RAP Tag Overflow (UI-Control panel).

123-355 ERROR — RAP No Co Processor Exception (UI-Control panel).

123-356 ERROR — RAP Short of Area (UI-Control panel).

123-357 ERROR — RAP Cancel Wait Status (UI-Control panel).

123-358 ERROR — RAP Timeout (UI-Control panel).

123-359 ERROR — RAP Queue Overflow (UI-Control panel).

123-360 ERROR — RAP Context Failure (UI-Control panel).

123-361 ERROR — RAP Object Failure (UI-Control panel).

123-362 ERROR — RAP No Object (UI-Control panel).

123-363 ERROR — RAP Invalid ID (UI-Control panel).

123-364 ERROR — RAP Parameter Failure (UI-Control panel).

123-365 ERROR — RAP Reserve Attribute (UI-Control panel).

123-366 ERROR — RAP Reserve Function Code (UI-Control panel).

123-367 ERROR — RAP Unsupported Function (UI-Control panel).

123-368 ERROR — RAP Short of UI Memory (UI-Control panel).

123-369 ERROR — RAP Invalid Interface Value (UI-Control panel).

123-370 ERROR — RAP Interface Length Failure (UI-Control panel).

123-371 ERROR — RAP Interface Parameter Failure (UI-Control panel).

123-372 ERROR — RAP Interface Sequence Failure (UI-Control panel).

123-373 ERROR — RAP Channel Failure (UI-Control panel).

123-374 ERROR — RAP Invalid User Job ID (UI-Control panel).

123-375 ERROR — RAP Internal Resource Failure (UI-Control panel).

123-376 ERROR — RAP Internal Memory Failure (UI-Control panel).

123-377 ERROR — RAP UI Timer Failure (UI-Control panel).

123-378 ERROR — RAP Interface Format Failure (UI-Control panel).

123-379 ERROR — RAP Dispatch Failure (UI-Control panel).

123-380 ERROR — RAP Copy Interface Failure (UI-Control panel).

123-382 ERROR — RAP Scanner Interface Failure (UI-Control panel).

123-383 ERROR — RAP Report Interface Failure (UI-Control panel).

123-384 ERROR — RAP Server Access Failure (UI-Control panel).

123-385 ERROR — RAP Service Object Overflow (UI-Control panel).

123-386 ERROR — RAP Invalid Service Object (UI-Control panel).

123-387 ERROR — RAP Invalid Service Object Attribute (UI-Control panel).

123-388 ERROR — RAP Attribute Failure (UI-Control panel).

123-389 ERROR — RAP Argument Failure (UI-Control panel).

123-390 ERROR — RAP Job Parameter Failure (UI-Control panel).

123-391 ERROR — RAP Job Actual Parameter Failure (UI-Control panel).

123-392 ERROR — RAP Auditron Failure (UI-Control panel).

123-393 ERROR — RAP EP Failure (UI-Control panel).

123-394 ERROR — RAP File Access Failure (UI-Control panel).

123-395 ERROR — RAP NVM Failure (UI-Control panel).

123-396 ERROR — RAP FF Failure (UI-Control panel).

123-397 ERROR — RAP MGR Failure (UI-Control panel).

123-398 ERROR — RAP Delay Release Queue Full (UI-Control panel).

123-399 ERROR — RAP Internal Failure (UI-Control panel).

123-400 ERROR — RAP Internal Failure (UI-Control panel).

124-310 ERROR — RAP DC132 11 — The product number was not specified.

124-311 ERROR — RAP DC132 09 — The serial number registration field failed.

124-312 ERROR — RAP DC132 12 — Product numbers did not agree.

124-313 ERROR — RAP DC132 10 — Serial numbers did not agree.

124-314 ERROR — RAP DC 132-01 — IOT Speed Failure.

124-315 ERROR — RAP DC 132-02 — IOT Speed Mismatch.

124-316 ERROR — RAP DC 132-04 — Product a/f Model Failure.

124-317 ERROR — RAP DC 132-04 — Product a/f All Product Model Mismatch.

124-318 ERROR — RAP Product Type for S/W Key Failure.

124-319 ERROR — RAP DC 132-08 — All Product Type For S/W Key Mismatch.

124-320 ERROR — RAP EEP ROM Failure.

124-321 ERROR — RAP Backup SRAM Failure. An NVM ROM write problem occurred on the ESS PWB.

124-322 ERROR — RAP DC 132-05 — Copy/Scan/Print S/W Key by PWE Failure.

124-323 ERROR — RAP DC 132-06 — Copy/Scan/Print S/W Key 1 Failure.

124-324 ERROR — RAP All Billings Mismatch.

124-325 ERROR — RAP Billing Restoration Failure.

124-333 ERROR — RAP ASIC Failure (Panther).

124-334 ERROR — RAP Standard Font ROM Error.

124-335 ERROR — RAP Font ROM Not Found.

124-337 ERROR — RAP ESS Standard RAM Error.

124-338 ERROR — RAP Same Font ROMs Found.

124-339 ERROR — RAP ROM DIMM of another product found.

124-340 ERROR — RAP The three CRUM market destination values are not set up (0 or different).

124-341 ERROR — RAP One CRUM market destination value is different (IOT).

124-342 ERROR — RAP One CRUM market destination value is different (SYS 1).

124-343 ERROR — RAP One CRUM market destination value is different (SYS 2).

124-350 ERROR — RAP The three CRUM OEM destination values are not set up (0 or different).

124-351 ERROR — RAP One CRUM OEM destination value is different (IOT).

124-352 ERROR — RAP One CRUM OEM destination value is different (SYS 1).

124-353 ERROR — RAP One CRUM OEM destination value is different (SYS 2).

124-360 ERROR — RAP CRUM Valid/Invalid is not set up at the three locations (0 or different values).

124-361 ERROR — RAP CRUM Validation Failure MCU.

124-362 ERROR — RAP CRUM Validation Failure SYS 1.

124-363 ERROR — RAP CRUM Validation Failure SYS 2.

124-372 ERROR — RAP IOT sc Soft Failure.

124-373 ERROR — RAP IOT Manager SW Failure.

124-374 ERROR — RAP IOT IM Device Driver SW Failure.

124-380 ERROR — RAP CRUM Market fail ALL (2).

124-381 ERROR — RAP CRUM Market fail MCU (2).

124-382 ERROR — RAP CRUM Market fail SYS 1 (2).

124-383 ERROR — RAP CRUM Market fail SYS 2 (2).

124-390 ERROR — RAP CRUM OEM fail ALL (2).

124-391 ERROR — RAP CRUM OEM fail MCU (2).

124-392 ERROR — RAP CRUM OEM fail SYS 1 (2).

124-393 ERROR — RAP CRUM OEM fail SYS 2 (2).

124-701 ERROR — RAP Side Tray to Center Tray.

124-704 ERROR — RAP The output tray was changed from the Folder Tray to the Center Tray and printing continued.

124-705 ERROR — RAP Punching Cancelled.

124-706 ERROR — RAP Folding Cancelled.

124-708 ERROR — RAP The output tray has been changed to the Sub Tray because a failure was detected in the specified output tray.

124-709 ERROR — RAP Stapler Sheet Count is too high.

125-311 ERROR — RAP PSWcont Unexpected Failure.

127-210 ERROR — RAP DFE Communication Failure.

127-211 ERROR — RAP DFE Parameter Error.

127-212 ERROR — RAP ExtPrint Check Mode Error.

127-213 ERROR — RAP External Print IF Mismatch.

127-220 ERROR — RAP Communication Error (video) detected by the DFE.

127-221 ERROR — RAP Communication Error (Command) detected by the DFE.

127-310 ERROR — RAP ESR Task Fatal Error.

127-311 ERROR — RAP ExtPRT.

127-320 ERROR — RAP DFE Critical Failure.

127-337 ERROR — RAP Job Template HDD Write Error.

127-342 ERROR — RAP Job Template Monitor Failure.

127-353 ERROR — RAP LPD Soft Fatal Error.

127-354 ERROR — RAP FTP Server Software Failure.

127-396 ERROR — RAP Mail I/O Soft Fatal error.

127-398 ERROR — RAP IPP Soft Fatal Error.

127-399 ERROR — RAP JME Soft Fatal Error.

202-399 ERROR — RAP Timer Internal Fail.

Современные копировальные аппараты Xerox отличаются качество, надежностью и «быстрым» стартом. Также у них существует множество особенностей, которые отличают их от принтеров других производителей. Например, используется тефлоновый вал, а не термопленка.

Однако избегать различных поломок и ошибок пока не удается ни одному устройству. К самым частым неисправностям у принтеров Xerox относятся: залипание или повреждение датчика бумаги, повреждение роликов подачи, часто требуется перепрошивка программного обеспечения.

Если у вас возникнут вопросы насчет того, как исправить код ошибки копировального аппарата Xerox, то вы можете обратиться к специалистам нашего сервисного центра.

Основные коды ошибок копировальных аппаратов Xerox и способы их устранения:

• Коды ошибок Xerox 1012, 1012(RE)
• Коды ошибок Xerox 1020
• Коды ошибок Xerox 1025
• Коды ошибок Xerox 1035
• Коды ошибок Xerox 1038
• Коды ошибок Xerox 2830
• Коды ошибок Xerox 5011, 5012, 5014
• Коды ошибок Xerox 5016, 5017, 5316, 5317
• Коды ошибок Xerox 5018, 5028
• Коды ошибок Xerox 5312, 5313, 5314
• Коды ошибок Xerox 5318, 5320, 5322
• Коды ошибок Xerox 5328
• Коды ошибок Xerox 5330
• Коды ошибок Xerox 5340, 5343
• Коды ошибок Xerox 5345
• Коды ошибок Xerox 5350, 5352
• Коды ошибок Xerox 5355
• Коды ошибок Xerox 5622
• Коды ошибок Xerox XC520, 540, 560, 580

Xerox 1012, 1012(RE)

Код ошибки	Описание
E1	Jam between paper feed and fuser
E3	Jam in fuser
E5	Clam shell open
E6	Paper feed section cover is open
J1	Toner cartridge near empty
J3	Drum cartridge not seated properly
J7	Waste toner full (replace drum cartridge)
L6	Key counter out
L8	Exposure area overheat
U1	No clock pulse (drive problem)
U2	Scan problem
U3	Lens/mirror problem (RE model only)
U4	Heat problem
U8	Exposure lamp control circuit problem
E1	Jam between paper feed and fuser
E3	Jam in fuser
E5	Clam shell open
E6	Paper feed section cover is open
J1	Toner cartridge near empty
J3	Drum cartridge not seated properly
J7	Waste toner full (replace drum cartridge)
L6	Key counter out
L8	Exposure area overheat
U1	No clock pulse (drive problem)
U2	Scan problem
U3	Lens/mirror problem (RE model only)
U4	Heat problem
U8	Exposure lamp control circuit problem

Xerox 1020

Код ошибки	Описание
LL	Probable bad heater lamp

Xerox 1025

Код ошибки	Описание
A1	DF jam
C1	PF jam cass. 1
C2	PF jam cass. 2
C3	PF jam cass. 3
C9	Bypass jam
E1-1	Paper jam before exit switch
E1-2	Paper jam
E1-5	Paper jam
E1-6	Paper jam
E3-3	Paper jam at exit switch
E3-4	Paper jam at exit switch
E5	Front door open
F1	Collator jam
F5	Collator interlock
F8	No power to collator
F9	Collator bin home switch
J7	250 copies since toner waste was full
L5	Original cass. not present after clearing interrupt
L6	Key counter
L8	Platen glass too hot
U1	Main motor clock pulse
U2	Scan problem
U3-1	Lens problem
U4-1	Open thermistor
U4-2	Low temperature
U4-4	Temperature
U4-5	Main PWB
U6-1	Main PWB
U6-2	Main PWB
U6-3	Main board battery
U6-4	Initialization
U8	Exposure lamp

Xerox 1035

Код ошибки	Описание
A9	Scanner location
C1	Paper feed — upper cassette
C2	Paper feed — lower cassette
C9	Bypass jam
E5	Clam shell is open
L6	Key counter
U1	Off/On
U2	Optics
U4	Low fuser temperature

Xerox 1038

Код ошибки	Описание
A1	DF jam
C1	PF jam cass. 1
C2	PF jam cass. 2
C3	PF jam cass. 3
C9	Bypass jam
E1-1	Paper jam before exit switch
E1-2	Paper jam
E1-5	Paper jam
E1-6	Paper jam
E3-3	Paper jam at exit switch
E3-4	Paper jam at exit switch
E5	Front door open
F1	Collator jam
F5	Collator interlock
F8	No power to collator
F9	Collator bin home switch
J7	250 copies since toner waste was full
L5	Original cass. not present after clearing interrupt
L6	Key counter
L8	Platen glass too hot
U1	Main motor clock pulse
U2	Scan problem
U3-1	Lens problem
U4-1	Open thermistor
U4-2	Low temperature
U4-4	Temperature
U4-5	Main PWB
U6-1	Main PWB
U6-2	Main PWB
U6-3	Main board battery
U6-4	Initialization
U8	Exposure lamp

Xerox 2830

Код ошибки	Описание
A9	Scanner location
C1	Paper feed — upper cassette
C2	Paper feed — lower cassette
C9	Bypass jam
E5	Clam shell is open
E5	Clam shell open
L6	Key counter
U1	Off/On
U2	Optics
U4	Low fuser temperature

Xerox 5011, 5012, 5014

Код ошибки	Описание
C8	Bypass jam/no paper
C9	Bypass jam
E1	Jam
E3	Fuser jam
E5	Clamshell open
E6	PF section cover open
J1	Toner cartridge amost empty
J3	Copy cart (drum unit) missing/not seated right
J7	Copy cartridge has run 18,000 copies
J8	Copy cartridge. Improperly seated or possible only one of two fuses in the cartridge blew
L6	Key counter
L8	Exposure glass too hot
U1	Drive problem
U2	Scan problem
U3	Lens or mirror drive problem
U4	Fuser problem. Heat lamp, thermoswitch, SSR, thermistor
U6	Battery on main board
U8	Exposure lamp or exposure lamp circuit

Xerox 5016, 5017, 5316, 5317

Code	Description
A1-1	Document feeder feed jam
A1-2	Document feeder belt jam
A2-1	Document feeder exit jam
A2-2	Duplex jam
A3	DAD interlock
A5	Duplex and DAD right side interlock
A6	Copier jams after
A9	Document feed belt drive motor
C1-3	Top cassette misfeed
C2-3	Middle cassette misfeed
C3-3	Bottom cassette misfeed
C9-3	Bypass misfeed
E1-11 to E1-14	Paper jam in machine. Did not reach exit switch soon enough
E1-6	Paper path jam
E3-31 to E3-34	Exit switch jam
E3-6	Fuser jam
E5	Front door interlock
E6	Right side interlock or TTM interlock
F1	Sorter jam
F5	Sorter interlock
F8	Sorter board to copier main board communication problem
F9	Sorter bins

Xerox 5018, 5028

Code	Description
A1	Document is ADF
A1-8	Main board received reset signal
A2	ADF jams
A6, A7	ADF jams
A9	ADF jams
C1 — C4	Feed jam
C5-1 to C5-4	Jams in various areas
C5-2	Jams in various areas
C5-3	Jams in various areas
C5-4	Duplex jam
E0	Machine has reset
E1	Jam
E1-E0	Registration jam
E1-E5	Clamshell interlock
E1-E6	Right side interlock
E1-E7	Two tray interlock
E1-E8	Sorter interlock
E1-E9	Copy cartridge interlock
E2	Reset signal happened
E3	Jam
E4	Exit jam
E4-10	Exit jam
E4-5	Clamshell interlock
E4-6	Right side interlock
E4-7	Two tray interlock. Duplex interlock
E4-8	Sorter interlock
E4-9	Copy cartridge interlock
E5	Clamshell interlock
E6	Right side interlock
E7	Duplex interlock
E9	Copy cartridge interlock
F3-1	Sorter bin home switch
F3-2	Sorter cam switch
F3-3	Sorter cam switch
J1-1	Add toner
J1-2	Temporary low toner signal
J2-0	Replace copy cartridge
L2	2000 copies left on copy cartridge
L3	ADF to machine communication problem
L4 (flashing)	1000 copies left on fuser web
rr	Bad EPROM on main board
U0	Main board
U2	Scan problem
U2-1	Scan home
U3-00	Cam drive problem
U3-01	Cam movement slow
U3-04	Main board to duplex communication
U3-09	Cam problem
U3-12	Jogger problem
U3-19	Cam problem
U3-21	Cam problem
U3-23	Cam problem
U3-29	Cam problem
U3-32	Cam problem
U3-34	Cam problem
U3-39	Cam problem
U3-43	Cam problem
U3-45	Cam problem
U3-49	Cam problem
U3-54	Cam problem
U3-56	Cam problem
U3-59	Cam problem
U4-1	Fuser problem. Long warm up
U4-2	Low fuser temperature after warm up
U4-3	High fuser temperature
U4-4	Open fuser thermistor
U4-6	Replace fuser web
U4-7	Thermistor signal problem
U7-1	Copy cartridge belt drive problem
U9-3	Exposure lamp problem
U9-4	Toner motor
U9-5	Problem in warm up

Xerox 5312, 5313, 5314

Код ошибки	Описание
C1	Upper paper feed problem. Did not reach feed sensor
C2	Lower paper feed problem. Did not reach feed sensor
E1	Exit jam. Paper did not reach exit sensor
E3	Exit jam. Paper still on exit sensor
J1	Add toner
J3	Copy cartridge (drum unit) not installed
J7	Copy cartridge (drum unit) must be replaced
J8	Copy cartridge (drum unit) problem
L6	Problem with an accessory. Installed but not initialized
U1	Drive problem. Main motor, gear etc.
U2	Scan problem
U3	Main board dip switches wrong. Lens drive problem
U4	Fuser problem. Heat lamp, thermal switch, overheat, thermistor.
U6	EPROM error
U8	Auto exposure sensor. No exposure lamp or weak lamp

Xerox 5318, 5320, 5322

Code	Description
A1-11	Original ready switch
A1-12	Feed sensor
A1-1 to A1-32	All indicate a paper path problem, etc. in the ADF
A1-21	Original ready switch and document registration sensor or both the document feed sensor and document registration sensor
A1-22	ADF registration sensor
A1-23	Original did not reach ADF registration sensor quickly enough
A1-24	ADF sensor stuck down too long
A1-25	ADF sensor actuated at the wrong time during single sheet feed
A1-26	ADF sensor not actuated quickly enough in sheet feed mode
A1-31	In reverse, ADF sensor is not actuated soon enough
A1-32	In reverse, ADF sensor is actuated too long
A2	ADF exit problems
A2-1	Original ready sensor and ADF exit switch are actuated or ADF feed in sensor and ADF exit switch are both actuated
A2-2	ADF exit switch
A2-3	ADF exit switch is not actuated on time
A3	Irregular size documents
A3-1	Wrong size original sensed in 1:1 mode
A3-2	Wrong size original sensed in the 2:1 mode
A5	ADF interlock
A5	ADF interlock
A6	ADF single sheet document reset.
A6-1	Reset original
A6-2	Reset sheet feeder
A7	Document cover interlock
A8	ADF exit interlock
C1	Tray 1 jam
C1-2	Paper feed problem in tray 1
C1-3	Paper does not reach registration
C2	Tray 2 jam
C3	Tray 3 jam
C3-1	Paper feed problem from tray 3
C3-2	Paper feed problem from tray 3
C3-3	Paper feed problem from tray 1
C6-1	Duplex paper feed problem
C6-2	Duplex and/or tray 1 paper feed problem
C6-3	Paper feed problem from tray 1
C7-1	Paper feed problem from HCF
C7-2	Paper feed problem from HCF on tray 1
C7-3	Paper feed problem from tray 1
C8	Paper stays in tray or duplex or HCF
C8-1	Paper on tray 1 feed sensor
C8-2	Paper on tray 2 feed sensor
C8-3	Paper on tray 3 feed sensor
C8-4	Paper on HCF feed sensor
C8-5	Paper in duplex section
C9	Bypass feed problem
C9-3	Paper from bypass did not reach registration sensor quickly enough
E1-10 to E1-25	Internal jam
E1-6	Paper on registration sensor
E2	Reset signal happened. Might read E-2 something else.
E3-30 to E4-14	Exit jam
E3-30 to E3-35	Exit switch actuated too long
E3-6	Exit jam
E3-6	Paper on exit switch
E4-10 to E4-14	Inverter sensor not actuated.
E4-10 to E4-45	Paper did not reach inverter switch soon enough
E4-15	Inverter sensor
E4-40 to E4-45	Duplex entry sensor
E4-6	Paper on inverter switch
E4-6	Inverter sensor
E5	Front door interlock
E6-1	Tray 1 interlock
E6-2	2 tray or duplex interlock
E6-3	HCF interlock
E7-2	Duplex inverter interlock
E7-3	Duplex interlock
E8-10 to E8-15	Paper on duplex feed sensor is not actuated soon enough
E8-6	Paper in duplex
E8-6 to E8-15	Duplex entry sensor
F1-1	Paper did not reach sorter
F1-2	Paper stayed on sorter feed sensor
F1-6	Sorter exit sensor
F3	Paper size not available for sort/stack
F5	Sorter interlock
H2-1	Communication problem between main board and duplex board
H2-2	Side guard sensor problem
H3-1	Communication problem between main board and HCF
H3-2	Upper limit sensor problem on HCF
H6-1	ADF size sensor
H6-2	ADF nudgeer sensor
H6-3	Belt drive motor does not have 24 volts. Black toner is empty, but 100 copies have been run without changing toner
J1	Black toner is empty, but 100 copies have been run without changing toner
J3	Replace copy cartridge
J3	No copy cartridge (drum unit)
J7	Copy cartrige must be replaced
J8-1	Wrong copy cartridge installed
J8-2	Copy cartridge EEPROM must be changed
L6	Auditron or other counter problem
L6	Key counter not installed
L8	Platen glass temperature is too high
L9	Communication problem between interimage erase/edge lamps and main board
U1-1	Main motor drive problem
U2-1	Scan home problem
U2-1 to U2-4	Scan home sensor
U2-2	Scan home problem or optics problem
U2-3, U2-4	Scan home problem
U3-1	Lens sensor problem
U4-1	Fuser thermistor open
U4-2	Fuser did not warm up properly
U4-3	Fuser temperature too high
U4-4	Fuser problem. Staying on too long
U4-6	High fuser temperature
U5-1	Sorter bin home switch not activated
U5-2	Sorter bin home switch stayed actuated
U5-3	Sorter bin home switch
U5-4	Sorter bin home switch
U6-1	ROM problem
U6-2	RAM problem
U6-3	Low battery
U6-4	Incorrect value in NVM. Reinitialize main board with code 20-96
U8-1	Exposure lamp problem
U8-2	Communication problem main board and exposure board
U8-3	Exposure lamp or exposure lamp board problem
U8-4 to U8-6	Problem with exposure lamp, lamp sensor, lamp board

Xerox 5328

Code	Description
A1	Document in ADF
A1-8	Main board received reset signal
A2	ADF jams
A6	ADF registration jam
A7	ADF interlock
A9	Tray 1 jam
C1	Tray 2 jam
C2	Tray 3 jam
C3	Bypass feed jams
C4	Machine has reset
E1	Jam
E1-5	Clamshell interlock
E1-6	Right side interlock
E1-7	Two tray interlock, or duplex interlock
E1-8	Sorter interlock
E1-9	Copy cartridge interlock
E1 or E1-0	Registration jam
E2	Reset signal happened
E3	Jam in transfer area
E4	Exit jam
E4-0	Exit jam
E4-5	Clamshell interlock
E4-6	Right side interlock
E4-7	Two tray interlock
E4-8	Sorter interlock
E4-9	Copy cartridge interlock
E5	Clamshell interlock
E6	Right side interlock
E9	Copy cartridge interlock
F3-1	Sorter bin home switch
F3-2	Sorter cam switch
F3-3	Sorter cam switch
F5	Sorter interlock
J1-1	Add toner
J1-2	Temporary low toner signal
J2-1, J2-2	Replace copy cartridge
J5, J6	ADF to machine communications problem
L2	2000 copies left on cartridge
L3	ADF to machine communications problem
L4	(flashing) 1000 copier left on fuser web
L6	Auditron or other counter problem
LL	Main board. Try simulation 1.1 to initialize
rc	Wrong operation panel installed
rr	Bad EPROM on main board. Try 1.1
U0	Main board
U2	Scan problem
U2-1	Scan home
U2-2	Scan home or scan encoder
U2-4	Scan home or scan dual page sensor
U2-7	Scan home
U4-1	Fuser problem. Long warm up
U4-2	Low fuser temperature after warm up
U4-3	High fuser temperature
U4-4	Open fuser thermistor
U4-6	Replace fuser web.
U4-7	Thermistor signal problem
U7-1	Copy cartridge belt drive problem
U9-3	Exposure lamp problem
U9-4	Toner motor
U9-5	Problem in warm-up

Xerox 5330

Code	Description
A1-1 to A1-32	All indicate a paper path problem, etc. in the ADF.
A2	ADF exit problems
A3	Irregular size documents
A5	ADF interlock
A6	ADF single sheet document reset.
A7	Platen interlock
A8	ADF exit interlock
C1	Tray 1 jam
C2	Tray 2 jam
C3	Tray 3 jam
C6-1, C6-2	Jams related to duplex
C6-3	Registration sensor, re tray 1
C7-1, C7-2	HCF feed problems
C7-3	Tray 1 feed problem
C8	Paper stays in tray or duplex or HCF
C9	Bypass feed problem
E1-10 to E1-25	Internal jam
E1-6	Paper on registration sensor
E2	Reset signal happened. Might read E-2 something else.
E3-30 to E4-14	Exit jam
E3-6	Exit jam
E4-10 to E4-14	Inverter sensor not actuated.
E4-15	Inverter sensor
E4-40 to E4-45	Duplex entry sensor
E4-6	Inverter sensor
E5	Front door interlock
E6-1	Tray 1 interlock
E6-2	2 tray or duplex interlock
E6-3	HCF interlock
E7-2, E7-3	Duplex interlock
E8-6 to E8-15	Duplex entry sensor
F1-1	Sorter entry sensor
F1-6	Sorter exit sensor
F3	Paper size not available for sort/stack
F5	Sorter interlock
J1	Add toner
J3	Replace copy cartridge
J7	Replace copy cartridge
J8-1	Wrong copy cartridge installed
J8-2	Copy cartridge EEPROM
L6	Auditron or other counter problem
L8	Platen glass temperature is too high
L9	Communication problem between interimage erase/edge lamps and main board
U1-1	Main motor drive problem
U2-1 to U2-4	Scan home sensor
U3-1	Lens sensor
U4-1	Open fuser thermistor
U4-2	Fuser did not warm up properly
U4-3	Fuser temperature too high
U4-4	Fuser problem. Staying on too long
U4-6	High fuser temperature
U5-1	Sorter bin home switch not activated
U5-2	Sorter bin home switch stayed actuated
U5-3	Sorter bin home switch
U5-4	Sorter bin home switch
U6-1	ROM problem
U6-2	RAM problem
U6-3	Low battery
U6-4	Incorrect value in NVM. Reinitialize main board with code 20-96
U8-1 to U8-6	Problem with exposure lamp, lamp sensor, lamp board

Xerox 5340, 5343

Code	Description
00-009; 030 to 033	A door was opened while paper was being fed
00-047	Paper in duplex
00-1	Auditron
00-2	Diagnostic error
00-3	Faults error
00-4	Ric error
00-5	Job manager system error
00-6	LLM interface
00-7	Standby error
00-8	Communications error
00-9	Xerographic error
01-300	Front interlock
01-310	Right upper interlock
01-315	Left upper interlock
01-320	Left lower interlock
01-325	Fuser interlock
02-910	Key counter missing
02-920	Wrong combination of accessories
03-321, 322, 326, 327	LLM to ISIL communications problems
03-328	IOT communications problem with duplex or tray 4
03-330	IOT communications problems with HCF
03-335, 03-336	LLM communications problems with edit
03-340	NVM memory
03-341, 03-347	Communications problems between IOT and sorter
03-350, 03-354	Communications problem with LLM and user interface
03-363, 03-364	Communications problem between LLM & optics
03-370, 03-373	Communications problem between LLM & DADF
03-380, 384
03-416, 03-422	RAM memory problem
03-424, 426	NVM memory problem
03-430, 432	Billing problem
03-439	GRAIB communications problem
03-440	RIC communications problem
03-441	RIC NVM problem
03-442	Modem
03-443, 03-458	RIC problems
03-460	Serial communications processor problem
04-300	Main motor or drive problem
05-100, 05-108	DADF registration sensor
05-110	DADF exit sensor
05-115, 120	DADF jams
05-305	DADF document drive
05-310, 312	DADF document sensor
05-316	DADF registration sensor jam
05-325	DADF exit sensor
05-335, 341, 345	DADF interlock switches
06-300, 06-310	Scan problems
06-315	Scan drive
06-320A, 320B, 320C, 325	Scan problem
06-330	Lens drive
06-340	Exposure control problem
06-342	LLM CPU problem
06-344, 06-350	Exposure cvontrol problem
06-352	IOT CPU problem
07-300, 315, 330, 345	Tray faults
07-360, 07-370	HCF problems
07-375, 380A, 380B	Duplex problems
08-100, 08-110	Feed problems. Lead edge of copy paper is late getting to feed sensor of tray 1
08-115, 08-162	Feed problem. Lead edge of copy paper is late getting to registration sensor
08-165	Paper jam at registration sensor
08-310, 08-370	Paper at a sensor when power is turned on
08-330	DADF nudger sensor
08-380	Registration side to side problem with home position
08-390	Nip
09-300	Copy cartridge finished (drum unit)
09-310	Add black toner Add color toner
09-320	Add color toner
09-330	Wrong copy cartridge (wrong drum unit)
09-340	Drum cartridge not installed properly
09-350	Waste toner full
100	A fault has occurred
10-100	Exit jam
10-105	Exit jam
10-110	Vertical sensor jam
10-120, 122, 125	Duplex jam
10-150, 155	Too much or not enough paper in duplex tray
10-300	Fuser thermistor
10-302	Low fuser temperature
10-304	Bad fuser temp
10-308	High fuser temperature or open thermistor
10-310	High fuser temperature
10-312	Fuser not up to temperature after energy save
10-314	Fuser problem
10-320	Fuser web finished
10-330, 335, 340	Exit switch, vertical sensor switch actuated when power is turned on
11-100, 11-116	Sorter jam
11-150, 11-176	Sorter auto stapler jam
11-310, 314, 316	Sorter interlock
11-325A, B, C, D, E, F, G	Sorter index
11-352, 354, 356	Sorter auto stapler interlocks
11-365A, B, C, D, E	Sorter auto stapler bin
11-370, 371, 372A, 373A, 373B, 374	Sorter auto stapler staple failure, staple home problem or tamper home problem
11-385A, 385B, 390A,B,C,D,E, 396A	Sorter auto stapler staple failure, staple home problem or tamper home problem
301	Fuser web must be replaced
302	Copy cartridge (drum unit) must be replaced
501	Tray 1 must be rebuilt
502	Tray 2 must be rebuilt
503	Tray 3 must be rebuilt
504	Tray 4 must be rebuilt
505	HCF must be rebuilt
506	Bypass must be rebuilt
507	Duplex unit must be rebuilt
508	Replace black developer
509	Replace red developer
510	Replace green developer
512	Replace brown developer
513	Copy cartridge (drum unit) will need replacing soon
514	Fuser web will need replacing soon
515	DADF belt should be replaced
516	DADF feed rollers should be replaced
517	Replace exposure lamp
518	Replace suction filter
519	Replace ozone filter
520	Replace optics filter
521	Replace particle filter
522	Replace upper fuser roller
523	Replace fuser pawls
524	Replace pressure roller
525	Replace pressure roller pawls
900-905	Key operator calls

Xerox 5345

Код ошибки	Описание
01-01	Frequency monitoring and zero cross problem
01-02	Interlock
01-03	AC power problem
01-04	Finisher interlock
01-05	24v problem
03-01	Optics to main board communication problem
03-02	Software reset problem
03-03	Could be punched holes in the lead edge of the original
03-04	Software problem
03-06	Low battery
03-07	NVM not initialized or is missing or defective
03-17	Communication problem between main board and finisher board
03-18	Initializes one NVM counter to agree to others
03-19	All three NVM counter to agree with others
03-20	Main board/interface board problems
03-21	Problem with RIC NVM
03-22	RIC modem problem
03-23	RIC real time clock failure.
03-25	RIC NVM problem or not initialized
03-27	NVM problem
03-28	Watchdog software problem
03-29	Microprocessor crystal not at correct frequency
03-30	No software response from finisher after 20 seconds have elapsed
06-01	Lens did not reach 1.1 position
06-02	1/2 rate scanner problem
06-03	Scan home problem
06-04	Scan home problem
06-05	Scan home problem
06-06	Scan encoder
06-07	Scan encoder
06-08	Scan drive boost
06-09	Scan encoder
06-11	Scan encoder pulse phases
06-12	Insufficient scan damping
07-01	Duplex tray not home during duplexing
07-02	Tray 2 not home when selected
07-13	Tray 2 height sensor problem
07-15	Tray 2 empty
07-16	Tray 1 door open
07-18	Tray 1 stack sensor
07-22	Tray 1 empty
07-26	Tray 1 bypass switch actuated too long
07-27	Tray 1 bypass switch deactuated too early
07-30	Paper in duplex
07-31	Paper in duplex
07-32	Duplex tray empty, when paper should be there
08-10	Paper did not reach tray 2 input tray sensor
08-11	Paper did not reach duplex input sensor
08-12	Paper did not reach tray 1
08-14	Paper did not leave tray 2 input sensor quickly enough
08-18	Trail edge did not reach tray 2 input sensor quickly enough
08-19	Trail edge did not reach tray 1 input sensor quickly enough
08-20	Paper in duplex
08-21	Paper in tray 2 input
08-22	Paper in tray 2 or duplex at wrong time
08-23	Paper at tray 1 input at wrong time
08-24	Paper in tray 1 at wrong time
08-28	Upper and lower nips problem
09-08	Low toner condition
09-12	Drum signals are out of range
09-13	Unstable drum patch readings
09-15	Patch is too dark
09-16	Patch is too light
09-17	Open toner container access cover
09-18	Low toner level
09-21	Low toner sensor disconnected
09-22	Low toner condition, even after machine has been theoretically, adding toner
10-02	Low fuser temperature
10-03	High fuser temperature
10-06	Paper did not reach out put switch
10-07	Paper stayed on output switch
10-10	Paper did not reach decurler sensor
10-11	Paper did not reach decurler sensor
10-12	Paper on decurler sensor
10-13	Paper did not reach duplex entry sensor in time
10-14	Paper did not reach duplex entry sensor in time
10-15	Paper on entry sensor at wrong time
10-17	Fuser temperature is too high and fuser relay has deactuated
12-01	Paper at finisher input sensor
12-02	Paper did not reach finisher
12-03	Paper reached finisher too soon
12-05	Paper at stapler
12-06	Paper at stapler
12-07	Paper did not reach stapler
12-08	Paper did not reach stapler
12-10	Complied motor not working properly
12-15	Eject motor problem and/or eject encoder
12-20	Stacker motor problem
12-21	Stacker interlock
12-22	Stacker bottom sensor
12-23	Stacker bottom sensor
12-24	Stacker bottom sensor senses full
12-25	Stack height sensor
12-26	Stack height sensor
12-27	Stack height sensor
12-30	Offset home sensor
12-31	Offset home sensor
12-32	OCT switch
12-35	Eject nip carriage
12-36	Eject cam interlock
12-37	Eject nip carriage open timing
12-38	Eject cam interlock
12-40	Tamper motor
12-41	Tamper home problem
12-42	Tamper home sensor
12-43	Staple load sensor
12-44	Tamper home sensor
12-45	Tamper home sensor
12-50	Low on staples
12-51	Stapler home sensor
12-52	Stapler home sensor
12-53	Eject cam interlock
33-37	Too few documents
55-01	RDH interlock switch open during use
55-04	Paper on bypass sensor
55-05	Paper at vacuum timing sensor
55-06	Paper on output sensor
55-10	No paper reached S31
55-20	Paper did not leave S31 at correct time
55-24	Set counter arm problem
55-25	Documents in input tray not detected
55-27	Lead edge did not reach S35 at correct time
55-2955-30	Trail edge did not reach S35 at correct time
55-31	S32, ADF registration sensor did not see paper at correct time
55-32	S32 did not see trail edge at correct time
55-33	S36 One too many documents
55-36	One too many documents
55-39	Hole count problem on document feeder belt
55-40	Document belt travel problem
55-41	Document belt mistracking or skewing
55-45	Paper at inverter sensor
55-47	Inverter sensor did not see paper lead edge at correct time
55-49	More than 50 sheets in input tray
55-50	Right side interlock
55-51	Left side interlock
55-55	Document on glass
93-93	NVM has to be initialized after new software installed

Xerox 5350, 5352

Code	Description
00-009, 030, 031, 032, 033	A door was opened while paper was being fed
00-047	Paper in duplex
00-1	Auditron
00-2	Diagnostic error
00-3	Faults error
00-4	Ric error
00-5	Job manager system error
00-6	LLM interface
00-7	Standby error
00-8	Communications error
00-9	Xerographic error
01-300	Front interlock
01-310	Right upper interlock
01-315	Left upper interlock
01-320	Left lower interlock
01-325	Fuser interlock
02-910	Key counter missing
02-920	Wrong combination of accessories
03-321, 322, 326, 327	LLM to ISIL communications problems
03-328	IOT communications problem with duplex or tray 4
03-330	IOT communications problems with HCF
03-335, 336	LLM communications problems with edit
03-340	NVM memory
03-341-347	Communications problems between IOT and sorter
03-350-354	Communications problem with LLM and user interface
03-363, 364	Communications problem between LLM & optics
03-370-03-373	Communications problem between LLM & DADF
03-380, 384
03-416-422	RAM memory problem
03-424, 426	NVM memory problem
03-430, 432	Billing problem
03-439	GRAIB communications problem
03-440	RIC communications problem
03-441	RIC NVM problem
03-442	Modem
03-443-458	RIC problems
03-460	Serial communications processor problem
04-300	Main motor or drive problem
05-100-108	DADF registration sensor
05-110	DADF exit sensor
05-115, 120	DADF jams
05-305	DADF document drive
05-310, 312	DADF document sensor
05-316	DADF registration sensor jam
05-325	DADF exit sensor
05-335, 341, 345	DADF interlock switches
06-300-310	Scan problems
06-315	Scan drive
06-320A, 320B, 320C, 325	Scan problem
06-330	Lens drive
06-340	Exposure control problem
06-342	LLM CPU problem
06-344-350	Exposure cvontrol problem
06-352	IOT CPU problem
07-300, 315, 330, 345	Tray faults
07-360-370	HCF problems
07-375, 380A, 380B	Duplex problems
08-100-110	Feed problems. Lead edge of copy paper is late getting to feed sensor of tray 1
08-115-162	Feed problem. Lead edge of copy paper is late getting to registration sensor
08-165	Paper jam at registration sensor
08-310-370	Paper at a sensor when power is turned on
08-330	DADF nudger sensor
08-380	Registration side to side problem with home position
08-390	Nip
09-300	Copy cartridge finished (drum unit)
09-310	Add black toner Add color toner
09-320	Add color toner
09-330	Wrong copy cartridge (wrong drum unit)
09-340	Drum cartridge not installed properly
09-350	Waste toner full
100	A fault has occurred
10-100	Exit jam
10-105	Exit jam
10-110	Vertical sensor jam
10-120, 122, 125	Duplex jam
10-150, 155	Too much or not enough paper in duplex tray
10-300	Fuser thermistor
10-302	Low fuser temperature
10-304	Bad fuser temp
10-308	High fuser temperature or open thermistor
10-310	High fuser temperature
10-312	Fuser not up to temperature after energy save
10-314	Fuser problem
10-320	Fuser web finished
10-330, 335, 340	Exit switch, vertical sensor switch actuated when power is turned on
11-100-116	Sorter jam
11-150-176	Sorter auto stapler jam
11-310, 314, 316	Sorter interlock
11-325A,B,C,D,E,F,G	Sorter index
11-352, 354, 356	Sorter auto stapler interlocks
11-365A,B,C,D,E	Sorter auto stapler bin
11-370,371,372A,373A,373B,374	Sorter auto stapler staple failure, staple home problem or tamper home problem
11-385A,385B,390A,B,C,D,E,396A	Sorter auto stapler staple failure, staple home problem or tamper home problem
301	Fuser web must be replaced
302	Copy cartridge (drum unit) must be replaced
501	Tray 1 must be rebuilt
502	Tray 2 must be rebuilt
503	Tray 3 must be rebuilt
504	Tray 4 must be rebuilt
505	HCF must be rebuilt
506	Bypass must be rebuilt
507	Duplex unit must be rebuilt
508	Replace black developer
509	Replace red developer
510	Replace green developer
512	Replace brown developer
513	Copy cartridge (drum unit) will need replacing soon
514	Fuser web will need replacing soon
515	DADF belt should be replaced
516	DADF feed rollers should be replaced
517	Replace exposure lamp
518	Replace suction filter
519	Replace ozone filter
520	Replace optics filter
521	Replace particle filter
522	Replace upper fuser roller
523	Replace fuser pawls
524	Replace pressure roller
525	Replace pressure roller pawls
900-905	Key operator calls

Xerox 5355

Код ошибки	Описание
01-01	Frequency monitoring and zero cross problem
01-02	Interlock
01-03	AC power problem
01-04	Finisher interlock
01-05	24v problem
03-01	Optics to main board communication problem
03-02	Software reset problem
03-03	Could be punched holes in the lead edge of the original
03-04	Software problem
03-06	Low battery
03-07	NVM not initialized or is missing or defective
03-17	Communication problem between main board and finisher board
03-18	Initializes one NVM counter to agree to others
03-19	All three NVM counter to agree with others
03-20	Main board/interface board problems
03-21	Problem with RIC NVM
03-22	RIC modem problem
03-23	RIC real time clock failure.
03-25	RIC NVM problem or not initialized
03-27	NVM problem
03-28	Watchdog software problem
03-29	Microprocessor crystal not at correct frequency
03-30	No software response from finisher after 20 seconds have elapsed
06-01	Lens did not reach 1.1 position
06-02	1/2 rate scanner problem
06-03	Scan home problem
06-04	Scan home problem
06-05	Scan home problem
06-06	Scan encoder
06-07	Scan encoder
06-08	Scan drive boost
06-09	Scan encoder
06-11	Scan encoder pulse phases
06-12	Insufficient scan damping
07-01	Duplex tray not home during duplexing
07-02	Tray 2 not home when selected
07-13	Tray 2 height sensor problem
07-15	Tray 2 empty
07-16	Tray 1 door open
07-18	Tray 1 stack sensor
07-22	Tray 1 empty
07-26	Tray 1 bypass switch actuated too long
07-27	Tray 1 bypass switch deactuated too early
07-30	Paper in duplex
07-31	Paper in duplex
07-32	Duplex tray empty, when paper should be there
08-10	Paper did not reach tray 2 input tray sensor
08-11	Paper did not reach duplex input sensor
08-12	Paper did not reach tray 1
08-14	Paper did not leave tray 2 input sensor quickly enough
08-18	Trail edge did not reach tray 2 input sensor quickly enough
08-19	Trail edge did not reach tray 1 input sensor quickly enough
08-20	Paper in duplex
08-21	Paper in tray 2 input
08-22	Paper in tray 2 or duplex at wrong time
08-23	Paper at tray 1 input at wrong time
08-24	Paper in tray 1 at wrong time
08-28	Upper and lower nips problem
09-08	Low toner condition
09-12	Drum signals are out of range
09-13	Unstable drum patch readings
09-15	Patch is too dark
09-16	Patch is too light
09-17	Open toner container access cover
09-18	Low toner level
09-21	Low toner sensor disconnected
09-22	Low toner condition, even after machine has been theoretically, adding toner
10-02	Low fuser temperature
10-03	High fuser temperature
10-06	Paper did not reach out put switch
10-07	Paper stayed on output switch
10-10	Paper did not reach decurler sensor
10-11	Paper did not reach decurler sensor
10-12	Paper on decurler sensor
10-13	Paper did not reach duplex entry sensor in time
10-14	Paper did not reach duplex entry sensor in time
10-15	Paper on entry sensor at wrong time
10-17	Fuser temperature is too high and fuser relay has deactuated
12-01	Paper at finisher input sensor
12-02	Paper did not reach finisher
12-03	Paper reached finisher too soon
12-05	Paper at stapler
12-06	Paper at stapler
12-07	Paper did not reach stapler
12-08	Paper did not reach stapler
12-10	Complied motor not working properly
12-15	Eject motor problem and/or eject encoder
12-20	Stacker motor problem
12-21	Stacker interlock
12-22	Stacker bottom sensor
12-23	Stacker bottom sensor
12-24	Stacker bottom sensor senses full
12-25	Stack height sensor
12-26	Stack height sensor
12-27	Stack height sensor
12-30	Offset home sensor
12-31	Offset home sensor
12-32	OCT switch
12-35	Eject nip carriage
12-36	Eject cam interlock
12-37	Eject nip carriage open timing
12-38	Eject cam interlock
12-40	Tamper motor
12-41	Tamper home problem
12-42	Tamper home sensor
12-43	Staple load sensor
12-44	Tamper home sensor
12-45	Tamper home sensor
12-50	Low on staples
12-51	Stapler home sensor
12-52	Stapler home sensor
12-53	Eject cam interlock
33-37	Too few documents
55-01	rdh interlock switch open during use
55-04	Paper on bypass sensor
55-05	Paper at vacuum timing sensor
55-06	Paper on output sensor
55-10	No paper reached S31
55-20	Paper did not leave S31 at correct time
55-24	Set counter arm problem
55-25	Documents in input tray not detected
55-27	Lead edge did not reach S35 at correct time
55-2955-30	Trail edge did not reach S35 at correct time
55-31	S32, ADF registration sensor did not see paper at correct time
55-32	S32 did not see trail edge at correct time
55-33	S36 One too many documents
55-36	One too many documents
55-39	Hole count problem on document feeder belt
55-40	Document belt travel problem
55-41	Document belt mistracking or skewing
55-45	Paper at inverter sensor
55-47	Inverter sensor did not see paper lead edge at correct time
55-49	More than 50 sheets in input tray
55-50	Right side interlock
55-51	Left side interlock
55-55	Document on glass
93-93	NVM has to be initialized after new software installed

Xerox XC520, 540, 560, 580

Код ошибки	Описание
H2	Fuser thermistor
H3	Fuser temperature too high. Must be reset in diagnostics
H4	Fuser temperature too low. Must be reset in diagnostics
L3	Scan problem
L4	Min motor drive problem
L8	Exposure lamp not lightning or not enough light reaching auto exposure sensor
P	Paper did not feed

Xerox 5622

Code	Description
A1-1 to A1-32	All indicate a paper path problem, etc. in the ADF
A2	ADF exit problems
A3	Irregular size documents
A5	ADF interlock
A6	ADF single sheet document reset
A7	Platen interlock
A8	ADF exit interlock
C1	Tray 1 jam
C2	Tray 2 jam
C3	Tray 3 jam
C6-1, C6-2	Jams related to duplex
C6-3	Registration sensor, re tray 1
C7-1, C7-2	HCF feed problems
C7-3	Tray 1 feed problem
C8	Paper stays in tray or duplex or HCF
C9	Bypass feed problem
E1-10 to E1-25	Internal jam
E1-6	Paper on registration sensor
E2	Reset signal happened. Might read E-2 something else
E3-30 to E4-14	Exit jam
E3-6	Exit jam
E4-10 to E4-14	Inverter sensor not actuated
E4-15	Inverter sensor
E4-40 to E4-45	Duplex entry sensor
E4-6	Inverter sensor
E5	Front door interlock
E6-1	Tray 1 interlock
E6-2	2 tray or duplex interlock
E6-3	HCF interlock
E7-2, E7-3	Duplex interlock
E8-6 to E8-15	Duplex entry sensor
F1-1	Sorter entry sensor
F1-6	Sorter exit sensor
F3	Paper size not available for sort/stack
F5	Sorter interlock
J1	Add toner
J3	Replace copy cartridge
J7	Replace copy cartridge
J8-1	Wrong copy cartridge installed
J8-2	Copy cartridge EEPROM
L6	Auditron or other counter problem
L8	Platen glass temperature is too high
L9	Communication problem between interimage erase/edge lamps and main board
U1-1	Main motor drive problem
U2-1 to U2-4	Scan home sensor
U3-1	Lens sensor
U4-1	Open fuser thermistor
U4-2	Fuser did not warm up properly
U4-3	Fuser temperature too high
U4-4	Fuser problem. Staying on too long
U4-6	High fuser temperature
U5-1	Sorter bin home switch not activated
U5-2	Sorter bin home switch stayed actuated
U5-3, U5-4	Sorter bin home switch
U6-1	ROM problem
U6-2	RAM problem
U6-3	Low battery
U6-4	Incorrect value in NVM. Reinitialize main board with code 20-96
U8-1 to U8-6	Problem with exposure lamp, lamp sensor, lamp board