062 380 xerox c405 ошибка

Модератор: vetal

Вернуться в Принтеры, МФУ, факсы, копиры формата A4

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 50

Go to printers

Fault Code 062-380 on Xerox Versalink C405DN

Troubleshooting

• Go Back
• Blog
• Xerox WorkCentre 6515 Versalink C405 C505 C605 Fault Code 062-380: Insufficient Lamp Brightness was Detected When Performing AGC

NOTE: Execute the IIT diagnosis and then call NVM location [715-030] again (press the

Change Settings button) to check the value (diagnosis result).

Table 1 LED

Current value

Component Name

00

Not applicable (No errors)

01

LED Lamp PWB

02

CCD Lens Assembly

03

CCD Flexible Flat Cable

10

LED Lamp Flexible Flat Cable

12

IIT-ESS Video Cable

14

IIT-ESS I/O Cable

17

LVPS-IIT/Fax Power Cable (DC Harness)

4.

After replacing the appropriate parts, again change the value for NVM location [715-030]

to «1» and then execute «NVM Write».

5.

Check that the current value column becomes «000».

6.

If the problem persists after performing the above procedure, continue and check the fol-

lowing:

•

LED Lamp broken:

Component Control

•

Check the Flat Cable between the LED Lamp PWB

J723

for open circuits, short circuits, and poor contacts (especially, check whether

the Flat Cable was inserted in a skewed manner).

•

Check the Flat Cable between the CCD Lens Assembly

J710

for open circuits, short circuits, and poor contacts (especially, check whether

the Flat Cable was inserted in a skewed manner).

•

The coaxial cable between the IIT PWB

open circuit, short circuit, and poor contact

Initial Issue

WorkCentre 5335 Family Service Documentation

PL No.

—

PL 1.4

PL 1.2

PL 1.2

PL 1.4

PL 18.4

PL 18.4

PL 18.4

[062-002]

(PL

1.2)

P/J7001

and the IIT PWB

P/J700

and the IIT PWB

P/J7191

and the ESS PWB

P/J336

BUS Updated 12/2011

BSD-ON:

BSD 6.1 — Document Illumination

BSD-ON:

BSD 6.6 — Image Input

Insufficient lamp brightness was detected when performing AGC.

NOTE: When turning the power OFF, turn OFF the power switch first and then the main power

switch.

Initial Actions

Check the light path for any obstacle, and the lamp, the lens, the mirror and the White Correct-

ing Plate for deterioration or contamination.

Procedure

1.

Turn the power ON and enter the Diag mode. Change the value for NVM location [715-

030] to «1» and then execute «NVM Write».

2.

A 3 or 4-digit number is displayed in the current value column.

3.

Check the upper 1 or 2 digits, or the lower 2 digits using the following table and replace

the appropriate parts.

Sample Display

•

110 (3-digit display):

P/

LED Lamp PWB failure and LED Lamp Flexible Flat Cable is damaged or has poor

contact.

P/

(The first digit «1» in «110» is the upper digit, which indicates the LED Lamp PWB («0»

in «01» is not displayed). The lower 2 digits «10» indicates the LED Lamp Flexible Flat

Cable.)

for

•

1000 (4-digit display):

The LED Lamp Flexible Flat Cable is damaged or has poor contact.

(The first 2 digits «10» in «1000» are the upper digits, which indicates the LED Lamp

Flexible Flat Cable. The lower 2 digits «00» indicates that nothing is applicable (no

failures).)

07/2011

2-779

Status Indicator RAPs

062-371, 062-380

1. 10-22-2021

   
   

   #1

   

   
   Senior Tech
   

   250+ Posts

   

   

   

   ---

   Rep Power

   14

   WorkCenter 6515, error 062-380
   

   Hello Companions.

   First to say that I do not handle this brand (I am a ricoh technician/distributor), it is a request from a customer, who has a Xerox WorkCenter 6515, and asks my technical department if we can solve this problem.

   The device throws this fault code «062-380» so it does not allow you to operate, someone can lend a hand. Thank you.

   ​Apologies for my English, it’s not my mother tongue and I’m helping the translator.
   ALL WILL BE WELL

   ---

2. 10-22-2021

   
   

   #2

   Re: WorkCenter 6515, error 062-380
   

   Insufficient lamp brightness was detected when performing AGC.

   ---

3. 10-25-2021

   
   

   #3

   

   
   Senior Tech
   

   250+ Posts

   

   

   

   ---

   Rep Power

   14

   Re: WorkCenter 6515, error 062-380
   

   Originally Posted by adriansto
   

   Se detect� un brillo insuficiente de la l�mpara al realizar AGC.

   I understand that this failure may be due to the explorer’s lamp being dirty, or it being melted/broken.

   True? In the case of dirt, it should be possible to clean both the lamp and the mirrors of the explorer.

   You could confirm this to me, or it’s another lamp and I’m getting confused. Thank you.

   Last edited by UNICORNico; 10-25-2021 at 04:09 PM.

   ​Apologies for my English, it’s not my mother tongue and I’m helping the translator.
   ALL WILL BE WELL

   ---

4. 10-25-2021

   
   

   #4

   Re: WorkCenter 6515, error 062-380
   

   [QUOTE=UNICORNico;1945975]

   Originally Posted by adriansto
   

   You could confirm this to me, or it’s another lamp and I’m getting confused. Thank you.

   It is about scanner lamp. Under the scanner glass it is white band ( label ) Check that label is clean, check if the scanner mirrors are clean. All of these works on AGC = Automatic Gain Control

   ---

5. 10-25-2021

   
   

   #5

   

   
   Junior Member
   

   

   ---

   Rep Power

   0

   Re: WorkCenter 6515, error 062-380
   

   You have to replace the IIT assy , ie the scanner assy below is description of the fault ,

   062-311, 313, 321, 360, 371, 380, 386, 389, 393, 396-398 IIT
   Fail RAP
   062-311 Error detected in IISS software.
   062-313 Unexecutable Scan command error.
   062-321 Unexecutable Scan command error.
   062-360 Carriage home position error is detected.
   062-371 IIT failure Lamp error is detected.
   062-380 Insufficient lamp brightness was detected when performing AGC.
   062-386 During AOC (darkness adjustment), detected CCD output error.
   062-389 Overrunning of CRG was detected.
   062-393 CISASIC communication error is detected.
   062-396 Connection problem of CIS flat cable was detected.
   062-397 Connection problem of ESS Video cable was detected.
   062-398 Connection problem of ESS I/O cable was detected.
   Procedure
   WARNING
   Ensure that the electricity to the machine is switched off while performing tasks that do
   not need electricity. Refer to [GP 4]. Disconnect the power cord. Electricity can cause
   death or injury. Moving parts can cause injury.
   1. Power the machine down then back up, [GP 4], the error persists,
   2. Clean the scanner platen and the white stripe, [GP 34], the error persists,
   3. Install a new IIT Assembly, [REP 50.1.2], the error persists,
   4. Install a new DADF Assembly, [REP 50.1.1],

   ---