Hardware error 03130031-2F1F is the purge sensor error. Good news, the service manual says this one is an easy fix.
What The Code Means
For those that want to know, the 2F1F error means the recovery system has been driven but no sensor interrupt occurs. The recovery system has been driven to close the cap, but the cap has not been capped successfully.
The Fix
A simple reboot should do the trick. Before doing anything, please ensure there is nothing preventing the carriage from properly docking on the right side. To do this, lift the upper cover and observe. Improper power cycles can cause much larger problems.
Once you are certain there are no obstructions, power down the printer. Please wait a few moments before turning the power back on.
If the error clears, congratulations, you are good. If the error comes back, you have a few options.
Option 1
Repairing the printer is the favored option when it costs less than replacement. We do recommend having any repairs completed by a Canon Authorized Service Technician. In our experience, this option has the highest success rate.
We recommend finding an independent servicer for models that are no longer supported by Canon. Only as a last resort should you attempt making the repair yourself.
Make sure the power supply has been disconnected before attempting any repairs on your own. Electronic devices are capable of causing injury, death, or further damage to the printer. We strongly recommend hiring a professional If you are not experienced with electronics.
Option 2
If the reboot did not work, this could be a very costly repair. The reason; you have to blindly start replacing parts that may not need to be replaced, but they have to be ruled out. You may quickly find yourself spending more to repair an old printer than you would spend to buy a new printer (and get a new warranty).
In case you didn’t know, newer computers and operating systems may not support older printer models. That means the next time you buy a computer, it may not work with your old, but newly repaired printer.
Check out the current Canon imagePROGRAF lineup by using the link to the right.
Canon IPF 765 ошибка 03130031-2f1f
помогите решить проблему
| Сообщение #1
Отправлено 28 июля 2020 — 19:29
Всем привет, имеем выпавшую ошибку,аппарат IPF765.Ошибка указывает на блок прочистки
Что на данный момент сделано и заменено:
Головка,новая,оригинальная
Блок прочистки стоит новый
На днях заменили главную плату б/у
В данный момент принтер выходит в рабочий режим но при установке(заправке) бумаги выпадает сразу в ошибку
Через сервисное меню дает заправить бумагу и даже можно сделать тест или отпечатать одно задание и ВСЕ
Куда копать дальше, кончились мысли,может кто что дельное предложит?
- Наверх of the page up there ^
-
0
| Сообщение #2
Отправлено 17 декабря 2020 — 18:31
Robinzon54
Если голова заведомо рабочая (не факт), то или мать или датчик позиционирования на каретке (из разряда вариантов)
03130031-2F1F Pump cam sensor error Check the purge unit.
А вообще ошибка на помпу указывает как я понимаю
- Наверх of the page up there ^
-
0
- ← Предыдущая тема
- Широкоформатные плоттеры Canon
- Следующая тема →
- Вы не можете создать новую тему
- Вы не можете ответить в тему
1 человек читают эту тему
0 пользователей, 1 гостей, 0 скрытых пользователей
Скачать обновленную версию бесплатной программы PrintHelp 2023, купить Код Сброса —
Canon IPF 765 ошибка 03130031-2f1f
помогите решить проблему
| Сообщение #1
Отправлено 28 июля 2020 — 19:29
Всем привет, имеем выпавшую ошибку,аппарат IPF765.Ошибка указывает на блок прочистки
Что на данный момент сделано и заменено:
Головка,новая,оригинальная
Блок прочистки стоит новый
На днях заменили главную плату б/у
В данный момент принтер выходит в рабочий режим но при установке(заправке) бумаги выпадает сразу в ошибку
Через сервисное меню дает заправить бумагу и даже можно сделать тест или отпечатать одно задание и ВСЕ
Куда копать дальше, кончились мысли,может кто что дельное предложит?
- Наверх of the page up there ^
-
0
| Сообщение #2
Отправлено 17 декабря 2020 — 18:31
Robinzon54
Если голова заведомо рабочая (не факт), то или мать или датчик позиционирования на каретке (из разряда вариантов)
03130031-2F1F Pump cam sensor error Check the purge unit.
А вообще ошибка на помпу указывает как я понимаю
- Наверх of the page up there ^
-
0
- ← Предыдущая тема
- Широкоформатные плоттеры Canon
- Следующая тема →
- Вы не можете создать новую тему
- Вы не можете ответить в тему
1 человек читают эту тему
0 пользователей, 1 гостей, 0 скрытых пользователей
По целому ряду причин в плоттерах Canon imagePROGRAF могут возникнуть ошибки связанные с заполнением промежуточных чернильных ёмкостей (субтанков):
- 03130031-2F70 (общая ошибка)
- 03130031-2F71 (левый блок подачи чернил)
- 03130031-2F72 (правый блок подачи чернил)
Одной из наиболее вероятных причин можно считать аппаратную ошибку работы циклов прокачки картриджей.
Устранить проблему можно исключительно установкой оригинального картриджа. Причём после того, как проблема будет устранена, стоит дать плоттеру какое-то время поработать на оригиналах, а спустя время — менять на ПЗК или перезаправленные картриджи (оригинальные или совместимые, не принципиально). В таких условиях комплект оригиналов можно будет растянуть на достаточно большое количество циклов перезарядки.
- Вставить новые оригинальные картриджи, либо ПЗК с чипами, снятыми с новых оригинальных картриджей.
- Печатающее устройство проверяет список использованных ранее картриджей и видит, что картридж оригинальный и новый.
- iPF проверяет с помощью давления полноту и проходимость чернил. Если всё в порядке, то принтер выходит в готовность практически без заполнения.
Следует контролировать время работы подкачки, чтобы препятствовать износу шестерней.
Можно также попробовать ещё один способ сбросить ошибку:
- Заправьте картриджи и установите в плоттер.
- Включите плоттер и зайдите в сервисное меню.
- Через сервисное меню заменить печатающую голову.
- Выключить плоттер и снова включить.
Также проблема может быть в некачественных чернилах. Если показатели текучести и электропроводности существенно отличаются от оригинальных, плоттер выдаст ошибку.
Canon imagePROGRAF Hardware Error 03130031 Introduction
When your Canon imagePROGRAF Plotter is stuck with an on-screen hardware error 0313003, you need to call the service center to get assistance to get your Canon large format printer back into working state. In this printer service guide, we will give you some ideas to decode Hardware Error 03130031 and its subcodes of the 4 digits in the end. You can Buy Printer Spare Parts from here
Decoding the Error 03130031
Since we have detailed documentation about this error, it will be easier for you to diagnose the error. The hard part is, this error is closely related to the ‘print head’ and in most cases, you need to replace it to fix the plotter. To diagnose the error in the right way, we need subcode, which is the last four characters of the error code followed by 03130031, for example, ‘2F51’. The whole error code will look like this, 03130031-2F51. Ca’t find the subcode? Contact us for plotter repair in Dubai
Now you know how to find the sub error code, But how to understand the meaning of the 4-digit code followed by 03130031?
Fixing HP Designjet plotter error codes
Hardware Error 03130031 Codes and their Meaning
The 03130031-[Sub Code] error codes are about 45 variants. They all have different meanings and here is how to clear/fix them.
Below are the list of Hardware Error 03130031 Codes
03130031-260E – Gap detection failure
03130031-2618 – VH voltage error
03130031-290A – HDD not connected/not detected
03130031-291B – Lift shift timeout
03130031-291D – Spur cam sensor detector failure
03130031-2E23 – Cutter unit failure
03130031-2F13 – A/D converter external trigger output stop
03130031-2F14 – ASIC register not writable
03130031-2F16 – Mist fan error
03130031-2F17 – Platen fan lock detection error
03130031-2F1F – Purge sensor error
03130031-2F20 – Cap motor cam positioning error
03130031-2F22 – Pump shift timeout
03130031-2F23 – Purge motor error
03130031-2F24 – Cutter shift timeout error
03130031-2F25 – Carriage motor HP not detectable
03130031-2F26 – Carriage Motion Error
03130031-2F27 – Carriage shift timeout
03130031-2F28 – Lift shift timeout
03130031-2F2A – Cannot detect the LF home position
03130031-2F2B – LF operation failure
03130031-2F2C – Cassette shift timeout
03130031-2F2E – Roll shift timeout
03130031-2F3A – Ink supply valve open/close monitor timeout
03130031-2F3B – CS communication error
03130031-2F3C – LP nip sensor error
03130031-2F3D – HP pre-ejection pump motor overload error
03130031-2F3E – HP pre-ejection pump motor shift timeout
03130031-2F3F – An error other than overload error or shift timeout error
03130031-2F46 – The shutter HP sensor did not respond at startup
03130031-2F48 – VHT (heater drive power supply for printhead) error
03130031-2F49 – Left side printhead
03130031-2F4A – Main controller PCB error
03130031-2F4D – VHT leak detection error of left printhead
03130031-2F4E – VHT leak detection error of right printhead
03130031-2F4F – VHT leak detection error of left and right printhead or a single printhead
03130031-2F50 – Right side printhead
03130031-2F51 – Both printheads
03130031-2F52 – Detect that a carriage unit of a legacy model has been mounted
03130031-2F53 – Supply valve motor error of the left ink tank
03130031-2F54 – Supply valve motor error of the right ink tank
03130031-2F6C – Failed self-testing
03130031-2F70 – Indication at ink priming error in both sub tanks
03130031-2F71 – Indication at ink priming error in the left sub tank
03130031-2F72 – Indication at ink priming error in the right sub tank
03130031-4027 – Lift shift timeout error
How to fix Canon imagePROGRAF Hardware Error 03130031
Fixing Canon imagePROGRAF Hardware Error 03130031 can be a simple power-cycle or a replacement of very expensive spare parts. The first thing you need to do is to make sure there isn’t any paper stuck inside the Canon imagePROGRAF Plotter. And that the carriage assembly is in the docked state on the right side hand side of the plotter. You can verify this by opening the top cover or the Canon imagePROGRAF Plotter.
The second step is to turn off the Canon Plotter by pressing the power button. You should NEVER unplug the Plotter power code while it is ‘ON’. Once you turn the power off, turn the plotter ‘ON’ in the usual way. If it clears the error message, consider you are lucky and continue your print job as usual.
If the steps as mentioned above, don’t fix the error, you will need to may need to call Plotter Service Center in Dubai.
Cube’about Technology LLC. has been rated
4.5 out of
5 based on
4 reviews as of May 2018. —
Read all customer reviews.
Модератор: Коурдаков Алексей
- Ответить с цитатой
CANON ipf610
Подскажите пожалуйста, есть ли возможность по коду ошибки определить в чем заключается поломка?
Код ошибки :
03130031-2F1F
Во время печати принтер пискнул показал ошибку и предложил отключить — включить питание.
При этом головка остановилась не в правой(зона парковки) а в левой части принтера.
При включении головка едет в зону парковкино не доезжает и возвращается влево. а в правой части — в узле очистки головки несколько раз что-то щелкает и после этого принтер снова говорит показывает ошибку.
- v-pro
- Участник форума
- Сообщения: 2
- Зарегистрирован: 28 окт 2010 12:19
- Ответить с цитатой
Re: CANON ipf610
v-pro » 28 окт 2010 13:39
Вошел в сервисный режим, при попытке распечатать принтер попросил перезагрузить рулон и показал ошибку
03130031-2F13
больше я его пытать не стал )
- v-pro
- Участник форума
- Сообщения: 2
- Зарегистрирован: 28 окт 2010 12:19
- Ответить с цитатой
Re: CANON ipf610
Багама » 10 июн 2015 10:02
Добрый день всем! Были и у меня точно такие же проблемы. Открой правую сторону плоттера, чтобы был доступ, до нижней части (механизмы) парковочной площадки внимательно посмотри, есть ли посторонние предметы, или все ли шестерни на своих местах, у меня было слетела 1 на шестерня видимо для привода прижима капы к ПГ, я его аккуратно посадил на место и сразу всё заработало. Желаю Удачи! Багама.
- Багама
- Участник форума
- Сообщения: 1
- Зарегистрирован: 17 мар 2015 17:40
Вернуться в Форум по офисной технике Canon
Кто сейчас на конференции
Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 1
Сообщение на экране
Код ошибки
Проблема
Способ устранения проблемы
Ink Level: Check
0180104-1000
BK ink tank near-empty
Renew the ink tanks.
Ink Level: Check
0180101-1001
Y ink tank near-empty
Ink Level: Check
0180102-1002
M ink tank near-empty
Ink Level: Check
0180103-1003
C ink tank near-empty
Ink Level: Check
0180106-1006
MBK ink tank near-empty
Ink Level: Check
0180106-1007
MBK2 ink tank near-empty
Problem with Printhead.
Check printing results
01800500-1010
Number of non-discharging nozzles in printhead: Warning level
Clean the printheads. Renew the printheads. Identify the head management sensor unit.
Prepare for maint cart replacement.
01841001-281A
Maintenance cartridge near-full
Replace the maintenance cartridge.
Prepare for parts replacement.
Call for service.
Parts counter W1 level
Check the parts counter in service mode.
Parts replacement time has passed.
Call for service.
Parts counter W2 level
After checking the parts counter in service mode, replace any part whose counter is nearing the error value.
GARO W1221
01341221-1030
GARO (image mode): Unknown command
Verify the transmitted data before reprinting.
GARO W1222
01341222-1031
GARO (image mode): Invalid parameter count (no parameters)
GARO W1223
01341223-1032
GARO (image mode): Required parameter missing
GARO W1225
01341225-1034
GARO (image mode): Other warning
GARO W1226
01341226-103A
GARO (image mode): Image processing table error
GARO W1231
01341231-1035
GARO (setup): Unknown command
GARO W1232
01341232-1036
GARO (setup): Invalid parameter count
GARO W1233
01341233-1037
GARO (setup): Required parameter missing
GARO W1234
01341234-1038
GARO (setup): Data out of bounds
GARO W1235
01341235-1039
GARO (setup): Other warning
End of paper feed. Cannot feed paper more.
Forced feed limit
Check the remaining quantity of roll media.
This type of paper is not compatible with HP-GL/2.
01860006-1015
Non-support paper of HP-GL/2
Exchange for the compatible paper to HP-GL/2.
GL2:W0501
The memory is full.
01340501-1040
Memory full (HP-GL/2)
Check if there is the non-image area of the print. Verify the transmitted data before reprinting.
GL2:W0904
The memory is full.
01340904-1048
Overflow of Polygon buffer (HP-GL/2)
GL2:W0903
The memory is full.
01340903-1047
Overflow of replot buffer (HP-GL/2)
GL2:W0502
The parameter is out of range.
01340502-1041
Invalid parameter (HP-GL/2)
Verify the transmitted data before reprinting.
GL2:W0504
This command is not supported.
01340504-1043
Invalid command (HP-GL/2)
Mail box nearly full.
Delete unwanted data
011A1001-2901
The free hard disk space left for Personal Boxes in the printer’s hard disk does not have more than 1 GB, combined.
Delete unneeded jobs stored in Personal Boxes.
Mail box full.
Now printing without saving data.
01861003-2902
100 jobs are stored in the Personal Box.
Delete unneeded jobs stored in Personal Boxs.
Not much ink is left.
Prepare to replace the ink.
01810103-1003
C ink tank near-empty
Renew the C ink tank.
Not much ink is left.
Prepare to replace the ink.
01810102-1002
M ink tank near-empty
Renew the M ink tank.
Not much ink is left.
Prepare to replace the ink.
01810101-1001
Y ink tank near-empty
Renew the Y ink tank.
Not much ink is left.
Prepare to replace the ink.
01810106-1006
MBK ink tank near-empty
Renew the MBK ink tank.
Not much ink is left.
Prepare to replace the ink.
01810104-1000
BK ink tank near-empty
Renew the BK ink tank.
Ink tank is empty.
Replace the ink tank.
01810303-1403
C ink tank empty
Renew the C ink tank.
Ink tank is empty.
Replace the ink tank.
01810302-1402
M ink tank empty
Renew the M ink tank.
Ink tank is empty.
Replace the ink tank.
01810301-1401
Y ink tank empty
Renew the Y ink tank.
Ink tank is empty.
Replace the ink tank.
01810306-1406
MBK ink tank empty
Renew the MBK ink tank.
Ink tank is empty.
Replace the ink tank.
01810304-1400
BK ink tank empty
Renew the BK ink tank.
No ink tank loaded.
Check ink tank.
01810103-1413
C ink tank removal
Attach the C ink tank.
No ink tank loaded.
Check ink tank.
01810102-1412
M ink tank removal
Attach the M ink tank.
No ink tank loaded.
Check ink tank.
01810101-1411
Y ink tank removal
Attach the Y ink tank.
No ink tank loaded.
Check ink tank.
01810106-1416
MBK ink tank removal
Attach the MBK ink tank.
No ink tank loaded.
Check ink tank.
01810104-1410
BK ink tank removal
Attach the BK ink tank.
The paper is too small.
013200D2-1051
Size clip error
Check the media size check. Change the media size.
Maximum jobs stored.
Delete unwanted data.
011A1006-2907
Saved jobs exceed the Personal Box capacity.
Press the stop button to cancel the print job. Delete print jobs from the queue.
Delete unneeded jobs stored on the hard disk.
PHead needs cleaning.
Press Online to clear error.
03800500-280C
Printhead found to have many non-discharging nozzles during a non-discharging inspection (printing paused)
Clean the printhead. Identify the nozzles in a nozzle check pattern. Replace the printhead.
Paper size not detected.
Lift the release lever and reload the paper.
03010000-200C
Unable to detect the leading end of paper
Check the leading end of paper. Reload the paper.
Leading edge detection error.
Lift the release lever and align leading edge with orange line.
03010000-200D
Unable to detect the trailing end of cut sheet
Check the sheet length. Check to see if paper has not jammed.
Paper size not detected.
Lift the release lever and reload the paper.
03010000-2017
Paper (right) edge detection error
Check the right edge of paper. Check the paper type.
Paper size not detected.
Lift the release lever and reload the paper.
03010000-2018
Paper (left) edge detection error
Check the left edge of paper.
Check the paper type.
Cannot adjust printhead.
Press Online to clear the error and readjust printhead.
03863000-2820
Printhead registration unadjustable
Check the paper on which a pattern is printed for smears. Check the environment for interferences from outside light.
Clean the printhead.
Cannot adjust printhead.
Press Online to clear the error and readjust printhead.
03863000-2821
LF unadjustable
Check the paper on which a pattern is printed for smears. Check the environment for interferences from outside light.
Clean the printhead.
Cannot print as specified.
Lift the release lever and replace paper with A4/ LTR (vertical) or larger.
03010000-2E1F
Undersized paper loaded for internal printing (A4 or larger)
Replace with A4/Letter or any larger-sized paper.
Cannot print as specified.
Lift the release lever and replace paper with A3/ Ledger (vertical) or larger.
03010000-2E1F
Undersized paper loaded for internal printing (A3 or larger)
Replace with A3/11″x17″ or any larger-sized paper.
Cannot print as specified.
Lift the release lever and replace roll with 10 in. wide or larger roll.
03010000-2E1F
Undersized paper loaded for internal printing (roll media)
Replace with roll media at least 10 inches in width.
Cannot detect paper
Remove paper and press Load/Eject.
03010000-2E25
Paper jam while feeding/ejecting/printing
Remove the paper jam and reload the paper.
Cannot feed paper
Lift the release lever and reload paper.
03010000-2E27
Paper jam during feeding/printing/ejection
Reload the paper.
This paper cannot be used.
Check supported paper sizes.
03010000-200E
Undersized paper (cut sheets/roll media)
Replace with larger-sized paper.
This paper cannot be used.
Check supported paper sizes.
03010000-200F
Oversized paper (cut sheets/roll media)
Replace with smaller-sized paper.
Use another paper.
Press Online to clear the error.
03010000-2F33
Unadjustable because of transparent media
Replace with adjustable media.
Paper loaded askew.
Lift the release lever.
03016000-2010
Skew
Correct the skew in the paper and reload it.
Paper size not detected.
Reload paper.
03010000-200A
Unable to detect the paper width (Paper loaded at an improper position)
Reload the paper
Paper jam.
Press Load/Eject and reload the paper.
03010000-2E27
Paper jam during feeding/printing/ejection
Reload the paper
Paper size not detected.
Lift the release lever and reload the paper.
03010000-200C
Roll media loading size detection failure
Reload the roll media.
Cannot adjust eccentric.
Press Online to clear the error.
03863000-2822
Eccentricity correction disabled
Check to see if paper has not jammed.
Sheet printing is selected.
Press Load/Eject and load sheets.
03860002-2E02
Data with a cut sheet specification has been received but no cut sheets are loaded.
Load cut sheets at the paper tray port.
Roll printing is selected, but sheets are loaded.
Press OK, remove the sheets, and load a roll.
03860002-2E0A
Data with a roll media specification has been received when a cut sheet tray is loaded.
Replace with roll media.
Roll printing is selected.
Press Load/Eject and load a roll.
03060A00-2E00
Data with a roll media specification has been received but no roll media are loaded.
Load roll media.
No Roll Feed Unit.
Turn printer off and install roll feed unit.
03060A00-2E0E
Roll media unit not installed
Install the roll media unit.
The roll is empty.
Lift the release lever and replace the roll.
03060A00-2E1B
Roll media end
Renew the supply of roll media.
Wrong paper feed slot for this paper type.
Press Load/Eject and reload the paper.
03061000-2E15
Paper type mismatch
Check the type of paper that can be fed and reload the paper.
Manual printing is selected, but a roll is loaded.
Press Load/Eject and remove the roll.
03860001-2E0C
Data with a cut sheet specification has been received when roll media are loaded.
Load cut sheets at the paper tray port.
Hardware error.
03130031-2E23
Turn off printer, wait, then turn on again.
03130031-2E23
Cutter unit failure
Check the cutter unit.
Hardware error.
03130031-2E14
Turn off printer, wait, then turn on again.
03130031-2F14
Writing to the ASIC register disabled
Replace the main controller PCB
Hardware error.
03130031-2E16
Turn off printer, wait, then turn on again.
03130031-2F16
Mist fan error
Check the mist fan.
Hardware error.
03130031-2E17
Turn off printer, wait, then turn on again.
03130031-2F17
Suction fan lock detection error
Check the suction fan.
Hardware error.
03130031-2E20
Turn off printer, wait, then turn on again.
03130031-2F20
Purge motor cam position error
Check the purge unit.
Hardware error.
03130031-2E22
Turn off printer, wait, then turn on again.
03130031-2F22
Pump travel timeout
Check the purge unit.
Hardware error.
03130031-2E23
Turn off printer, wait, then turn on again.
03130031-2F23
Purge motor error Pump inoperable
Check the purge unit.
Hardware error.
03130031-2E25
Turn off printer, wait, then turn on again.
03130031-2F25
Unable to detect the carriage motor home position
Check the carriage unit. Check the linear encoder for smears.
Hardware error.
03130031-2E26
Turn off printer, wait, then turn on again.
03130031-2F26
Carriage inoperable
Check the carriage unit and surrounding parts.
Hardware error.
03130031-2E27
Turn off printer, wait, then turn on again.
03130031-2F27
Carriage travel timeout
Check the carriage unit and surrounding parts.
Hardware error.
03130031-2E1F
Turn off printer, wait, then turn on again.
03130031-2F1F
Pump cam sensor error
Check the purge unit.
Hardware error.
03130031-2E2A
Turn off printer, wait, then turn on again.
03130031-2F2A
Unable to detect the feed roller home position
Check the feed roller encoder and surrounding part. Check to see if paper has not jammed.
Hardware error.
03130031-2E29
Turn off printer, wait, then turn on again.
03010000-2F29
Feed motor timeout (Roll media)
Check the roll feed unit. Check roll media. Check to see if paper has not jammed in the printer.
Hardware error.
03130031-2E2E
Turn off printer, wait, then turn on again.
03130031-2F2E
Roll travel timeout
Check the roll feed unit.
Hardware error.
03130031-4027
Turn off printer, wait, then turn on again.
03130031-4027
Lift travel timeout error
Check the carriage unit and surrounding parts.
Hardware error.
03130031-2E13
Turn off printer, wait, then turn on again.
03130031-2F13
A/D converter external trigger output stop detection hardware error 1
Replace the new printhead.
Hardware error.
03130031-2F32
Turn off printer, wait, then turn on again.
03130031-2F32
Multi sensor error
Check the environment for interferences from outside light.
Replace the multi sensor unit.
Hardware error.
03130031-2F3A
Turn off printer, wait, then turn on again.
03130031-2F3A
Valve motor error
Check the ink supply unit.
Hardware error.
03130031-2F3B
Turn off printer, wait, then turn on again.
03130031-2F3B
CS communication error
Remove the ink tanks and then reload them. Check the main controller PCB.
Hardware error.
03130031-260E
Turn off printer, wait, then turn on again.
03130031-260E
Gap detection error
Check the carriage unit and surrounding parts. Replace the main controller PCB.
Hardware error.
03130031-2618
Turn off printer, wait, then turn on again.
03130031-2618
VH voltage error
Check the power supply unit.
Hardware error.
03130031-260F
Turn off printer, wait, then turn on again.
03130031-260F
Gap reference surface error
Replace the reference surface sheet.
Roll feed unit error
Turn off printer and check roll feed unit
03060B00-2E24
Roll feed unit failure
Replace the roll feed unit.
Unknown file. Check file format.
Turn off printer, wait a while, then turn it on again.
03900001-4049
ROM data for another model has been transferred.
Transmit valid ROM data.
Unknown file. Check file format.
Turn off printer, wait a while, then turn it on again.
03900001-4042
MIT data transfer failure
Verify the validity of MID data before transferring it.
Hardware error.
03130031-2F2B
Turn off printer, wait, then turn on again.
03130031-2F2B
LF operation failure
Check to see if paper has not jammed. Check the feed motor and feed roller.
Printhead error
Open top cover and replace the printhead.
03800200-2802
Invalid printhead installed
Replace printhead
Printhead error
Open top cover and replace the right printhead.
03800300-2801
Printhead DI compensation failure
Replace printhead
Printhead error
Open top cover and replace the right printhead.
03800400-2803
Printhead EEPROM error
Replace printhead
Hardware error.
03800500-2F2F
Turn off printer, wait, then turn on again.
03800500-2F2F
Non-discharging error
Identify the head management sensor unit
Replace the head management sensor unit
Replace the printhead
Hardware error.
03800500-2F30
Turn off printer, wait, then turn on again.
03800500-2F30
Non-discharging position adjustment error
Identify the head management sensor unit
Replace the head management sensor unit
Replace the printhead
Ink tank is empty.
Press OK and replace ink tank.
03810104-2500
Bk ink tank empty
Renew the Bk ink tank
Ink tank is empty.
Press OK and replace ink tank.
03810101-2501
Y ink tank empty
Renew the Y ink tank
Ink tank is empty.
Press OK and replace ink tank.
03810102-2502
M ink tank empty
Renew the M ink tank
Ink tank is empty.
Press OK and replace ink tank.
03810103-2503
C ink tank empty
Renew the C ink tank
Ink tank is empty.
Press OK and replace ink tank.
03810106-2506
MBk ink tank empty
Renew the MBk ink tank
Ink tank is empty.
Press OK and replace ink tank.
03810106-2507
MBk2 ink tank empty
Renew the MBk ink tank
Ink insufficient.
Press OK and replace ink tank.
03810204-2580
Low on the Bk ink tank (as during cleaning)
Replace with a fully replenished Bk ink tank
Ink insufficient.
Press OK and replace ink tank.
03810201-2581
Low on the Y ink tank (as during cleaning)
Replace with a fully replenished Y ink tank
Ink insufficient.
Press OK and replace ink tank.
03810202-2582
Low on the M ink tank (as during cleaning)
Replace with a fully replenished M ink tank
Ink insufficient.
Press OK and replace ink tank.
03810203-2583
Low on the C ink tank (as during cleaning)
Replace with a fully replenished C ink tank
Ink insufficient.
Press OK and replace ink tank.
03810206-2586
Low on the MBk ink tank (as during cleaning)
Replace with a fully replenished MBk ink tank
Ink insufficient.
Press OK and replace ink tank.
03810204-2590
Low on the Bk ink tank (during pre-printing checks)
Replace with a fully replenished Bk ink tank
Ink insufficient.
Press OK and replace ink tank.
03810201-2591
Low on the Y ink tank (during pre-printing checks)
Replace with a fully replenished Y ink tank
Ink insufficient.
Press OK and replace ink tank.
03810202-2592
Low on the M ink tank (during pre-printing checks)
Replace with a fully replenished M ink tank
Ink insufficient.
Press OK and replace ink tank.
03810203-2593
Low on the C ink tank (during pre-printing checks)
Replace with a fully replenished C ink tank
Ink insufficient.
Press OK and replace ink tank.
03810206-2596
Low on the MBk ink tank (during pre-printing checks)
Replace with a fully replenished MBk ink tank
Ink tank error.
Press OK and replace ink tank.
03830204-2540
Bk ink tank ID error
Replace with a valid Bk ink tank
Ink tank error.
Press OK and replace ink tank.
03830201-2541
Y ink tank ID error
Replace with a valid Y ink tank
Ink tank error.
Press OK and replace ink tank.
03830202-2542
M ink tank ID error
Replace with a valid M ink tank
Ink tank error.
Press OK and replace ink tank.
03830203-2543
C ink tank ID error
Replace with a valid C ink tank
Ink tank error.
Press OK and replace ink tank.
03830206-2546
MBk ink tank ID error
Replace with a valid MBk ink tank
Ink tank error.
Press OK and replace ink tank.
03830206-2547
MBk2 ink tank ID error
Replace with a valid MBk ink tank
No ink tank loaded.
Press OK and check ink tank.
03830104-2520
BK ink tank not installed
Install a Bk ink tank
No ink tank loaded.
Press OK and check ink tank.
03830101-2521
Y ink tank not installed
Install a Y ink tank
No ink tank loaded.
Press OK and check ink tank.
03830102-2522
M ink tank not installed
Install a M ink tank
No ink tank loaded.
Press OK and check ink tank.
03830103-2523
C ink tank not installed
Install a C ink tank
No ink tank loaded.
Press OK and check ink tank.
03830106-2526
MBK ink tank not installed
Install a MBk ink tank
No ink tank loaded.
Press OK and check ink tank.
03830106-2527
MBK2 ink tank not installed
Install a MBk ink tank
Top cover is open.
Turn off printer, wait a while, and turn it on again.
03031000-2F38
Top cover abnormally open
Close the top cover and turn on the printer again.
Ink tank cover is open.
Turn off printer, wait a while, and turn it on again.
03031000-2E10
Ink tank cover abnormally open
Close the ink tank cover and turn on the printer again.
Maintenance cartridge full.
Replace the maintenance cartridge.
03841001-2819
Maintenance cartridge full
Renew the maintenance cartridge.
No Maintenance
Cartridge capacity.
Replace the maintenance cartridge.
03841001-281B
Not enough space in the maintenance cartridge prior to cleaning
Replace the maintenance cartridge.
Maintenance cartridge problem.
Replace the maintenance cartridge.
03841201-2816
Maintenance cartridge EEPROM error
Renew the maintenance cartridge.
Maintenance cartridge problem.
Replace the maintenance cartridge.
03841201-2817
Maintenance cartridge ID error
Renew the maintenance cartridge.
Borderless printng not possible.
Check roll position.
Online: Print Load/Eject:
Change Paper
03861001-2405
Paper loaded at a position inaccessible for borderless printing
Check to see if a borderless printing spacer is installed. Reload the paper.
Borderless printng not possible.
Check paper size setting.
Online: Print
Load/Eject: Change Paper
03861001-2406
Data unfit for borderless printing
Check the paper size. Change the paper size.
Insufficient paper for job
Online: Print
Stop: Stop Printing
Load/Eject: Change Paper
03862000-2E09
Not enough roll media on remaining roll media quantity detection
Renew the supply of roll media.
Cannot cut paper.
Lift the release lever and reload the paper.
03870001-2015
Cutting failure
Cut paper manually. Check the cutter.
Cannot adjust optic axis.
Press Online to clear the error.
03863000-2824
Optical axis error
Check the multi sensor.
Check the head management sensor.
This type of paper is not compatible with HP-GL/ 2.
Online: Print
Stop: Stop Printing
Load/Eject: Change Paper
03061000-2E15
Non-support media of HP-GL/2
Exchange for the compatible paper to HP-GL/2 before reprinting.
Mail box full.
Delete unwanted data on your computer to resume printing.
Press Stop to cancel printing.
031A1001-2905
The job store executed when the free hard disk space left for Personal Boxes in the printer’s hard disk is full.
Delete unneeded jobs stored in Personal Boxes.
Mail box full.
Cannot save. Delete unwanted data on your computer to resume printing.
Press Stop to cancel printing.
031A1006-2906
The store executed when 32 jobs are stored in the Personal Box.
Delete unneeded jobs stored in Personal Boxes.
Hard disk error.
Press OK to reformat
031A1002-2908
Hard disk format error
Press the [OK] button to start reformatting the hard disk. When formatting is finished, the printer automatically restarts.
File read error.
Turn off printer, wait a while, and turn it on again.
Invalid files will be deleted.
031A1002-2909
Hard disk file error
Restart the printer. Only the corrupted files will be deleted, and the printer will restart.
Hardware error. 03800500-2F31
Turn off printer, wait, then turn on again.
03800500-2F31
Non-discharge detection optical axis error
Check the head management sensor. Replace the head management sensor. Replace the printhead.
Hardware error. 03130031-2F3C
Turn off printer, wait, then turn on again.
03130031-2F3C
LF pressure error
Check the pinch roller and surrounding part. Replace the pinch roller pressure drive unit.
No printhead
Install printhead.
03800100-2800
Printhead not installed
Install the printhead.
Wrong printhead. Open top cover and replace the printhead.
03800200-2811
Printhead version error
Replace the printhead.
No maintenance cartridge.
Check the maintenance cartridge.
03841101-2818
Mauntenance cartridge not installed
Install the maintenance cartridge.
This type of media is not compatible with HP-GL/ 2.
03860006-2825
Paper type mismatch at HP-GL/2 printing
Exchange for the compatible paper to HP-GL/2 before reprinting.
Cannot cut paper.
Lift the release lever and reload the paper.
03870001-2019
Cut failure (during jam occure)
Check the cutter unit and surrounding part. Replace the cutter.
Insufficient paper for job
03862001-2E31
Not enough roll media
Renew the supply of roll media.
Paper jam.
Manually rewind roll all the way and press OK.
03010000-2E3A
Madia load failure
Check the pick-up unit and roll media. Check to see if paper has not jammed.
Sheet printing is selected. Press Load/Eject and load sheets.
03060100-2E02
Cut sheet in not set
Load cut sheets at the paper tray port.
Borderless printng not possible. Check supported paper.
03861001-2408
Borderless printing disabled (unsupported size)
Check the media size. Change the media size.
Borderless printng not possible. Paper stretched or shrank.
Confirm usage cond. of the paper.
03861001-2407
Borderless printing disabled (engine detection)
Reload the paper.
Roll printing is selected. Press Load/Eject and load a roll.
03060A00-2E35
Roll media is not loaded for internal printing.
Reload the roll media.
Dislikes: 0
-
10-11-2021
#1
Senior Tech
100+ Posts
- Rep Power
- 14
Canon IPF 770 Plotter Hardware Error 03130031-2F1F
From what I have read does this mean the Purge Unit is Defective? I also noticed A lot of Air in the ink lines. If this is the Purge Unit could someone get me the part number?
Thanks in advance!
Hoosierdaddy
-
10-12-2021
#2
Re: Canon IPF 770 Plotter Hardware Error 03130031-2F1F
It’s the same purge unit used on all the iPFs: 650, 655, 680, 685, 750, 755, 760, 765, 770, 780, 785
Originally QM3-5988-000 … updated many times to currently QM4-3670-020.
If you turn the motor manually, you should be able to watch it work mechanically … pump in one direction, capping assembly in the other. When that ink starts hardening up into a rock the gears will break … you’ll hear the crunching.
Keep in mind that this may be just the first of a string of expensive issues. You can expect to need a printhead, at minimum. It probably hasn’t been properly capped in a while. =^..^=
Last edited by blackcat4866; 10-12-2021 at 01:11 AM.
If you’d like a serious answer to your request:
1) demonstrate that you’ve read the manual
2) demonstrate that you made some attempt to fix it.
3) if you’re going to ask about jams include the jam code.
4) if you’re going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=
-
10-12-2021
#3
Senior Tech
100+ Posts
- Rep Power
- 14
Re: Canon IPF 770 Plotter Hardware Error 03130031-2F1F
Originally Posted by blackcat4866
It’s the same purge unit used on all the iPFs: 650, 655, 680, 685, 750, 755, 760, 765, 770, 780, 785
Originally QM3-5988-000 … updated many times to currently QM4-3670-020.
If you turn the motor manually, you should be able to watch it work mechanically … pump in one direction, capping assembly in the other. When that ink starts hardening up into a rock the gears will break … you’ll hear the crunching.
Keep in mind that this may be just the first of a string of expensive issues. You can expect to need a printhead, at minimum. It probably hasn’t been properly capped in a while. =^..^=
Does the air in the line point to anything? Or does the Purge Unit and the Printhead cause that issue?
-
10-12-2021
#4
Re: Canon IPF 770 Plotter Hardware Error 03130031-2F1F
That’s further down that road, after you solve the first issue(s). =^..^=
If you’d like a serious answer to your request:
1) demonstrate that you’ve read the manual
2) demonstrate that you made some attempt to fix it.
3) if you’re going to ask about jams include the jam code.
4) if you’re going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=
Canon IPF 770 Plotter Hardware Error 03130031-2F1F
Originally Posted by blackcat4866
Tags for this Thread
Bookmarks
Bookmarks
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
- BB code is On
- Smilies are On
- [IMG] code is On
- [VIDEO] code is On
- HTML code is Off
Forum Rules
-
Опубликовано: 10 августа 2017
-
Просмотров: 11195
Сегодня меня позвали найти причину, почему плоттер Canon iPF-605 при включении выдаёт такое сообщение:
! Аппаратная ошибка 03130031-2E23
Выкл. принтер, подождите, включите снова.
Дальше не загружается, до меню не доходит и не даёт ничего сделать. Выполнение совета выключить и включить устройство также эффекта не имеет.
Рунет ничего не подсказал по данной ошибке, пришлось покопаться по англоязычным форумам. Выяснилось, что эта ошибка означает проблемы с ножом для отрезания бумаги.
Нож при включении плоттера должен быть расположен в крайнем левом положении, со стороны передней части плоттера. Возьмите его и протяните немного вправо-влево. Он должен легко скользить на своих полозьях. Если нож двигается с трудом или со звуками – значит его где-то подклинивает. Именно в этом и причина ошибки.
В моём случае – маленький кусочек бумаги застрял в полозьях и не давал ножу свободно перемещаться. Я его вытащил, проверил, что нож стал снова свободно скользить, сдвинул его до упора влево и включил питание.
Ура, проблема решена!
Здравствуйте. При включении аппарат сдвигает печатающую головку влево сантиметров на 15 и выдаёт аппаратную ошибку 03130031-2f1f, при этом слышен звук похожий на звук работающего насоса в районе блока картриджей. Подозрение на датчик положения головки, но незнаю как перепроверить. Слева есть три белых квадрата, по которым (как я думаю) должна выравниватся голова, если подвести ПГ к ним то при включении аппарат также сдвигает ПГ на 15 см. просто проезжая мимо позиционирующих квадратов.
История со слов хозяев аппарата: печатаем всё нормально, появилась эта ошибка, выключили, подождали, всё нормально, печатаем, застряла бумага, удалили бумагу, появилась ошибка и уже не пропала.
Коды ошибок, актуальные для Canon imagePROGRAF iPF670, iPF605, iPF770, iPF750, iPF710, iPF650, iPF700, iPF785, iPF610, iPF765, iPF680, iPF760, iPF510, iPF780, iPF600, iPF500, iPF685, iPF720, iPF670e, iPF671, iPF671e (для картриджей PFI-102, PFI-104, PFI-107).
Группы ошибок
| Code | Diagnosis | Что значит |
| 0181xxxx-xxxx | Ink warning | Некритичная ошибка чернил |
| 0180xxxx-xxxx | Printhead warning | Некритичная ошибка печатающей головки |
| 0184xxxx-xxxx | Maintenance cartridge warning | Некритичная ошибка картриджа |
| 0134xxxx-xxxx | GARO warning | Некритичная ошибка растрового драйвера |
| 0303xxxx-xxxx | Cover error | Ошибка крышки принтера |
| 0301xxxx-xxxx 0306xxxx-xxxx 0386xxxx-xxxx |
Media error | Ошибки загрузки носителя (например, бумаги) |
| 0313xxxx-xxxx | Sensors, fans, motors error | Ошибки датчиков, моторов и вентиляторов |
| 0380xxxx-xxxx | Printhead error | Ошибки печатающей головки |
| 0381xxxx-xxxx 0383xxxx-xxxx |
Ink error | Ошибки чернил |
| 0384xxxx-xxxx | Maintenance cartridge error | Ошибки картриджа отработки |
| 0387xxxx-xxxx | Cutter unit error | Ошибки резака |
| 0389xxxx-xxxx | Media take-up unit error | Ошибки устройства приёма носителя |
| 0390xxxx-xxxx | Firmware error | Ошибки прошивки |
| Exxx-xxxx | Service call error | Ошибки сервисного режима |
Ошибки с кодами и расшифровкой
| Сообщение на экране | Код ошибки | Проблема | Способ устранения проблемы |
| Ink Level: Check | 0180104-1000 | BK ink tank near-empty | Замените картриджи. |
| Ink Level: Check | 0180101-1001 | Y ink tank near-empty | |
| Ink Level: Check | 0180102-1002 | M ink tank near-empty | |
| Ink Level: Check | 0180103-1003 | C ink tank near-empty | |
| Ink Level: Check | 0180106-1006 | MBK ink tank near-empty | |
| Ink Level: Check | 0180106-1007 | MBK2 ink tank near-empty | |
| Problem with Printhead. Check printing results |
01800500-1010 | Number of non-discharging nozzles in printhead: Warning level | Очистите печатающие головки. Замените печатающие головки. Проверьте датчики печатающих головок. |
| Prepare for maint cart replacement. | 01841001-281A | Maintenance cartridge near-full | Замените картридж обслуживания. |
| Prepare for parts replacement. Call for service. |
Parts counter W1 level | Проверьте датчик деталей в меню обслуживания. | |
| Parts replacement time has passed. Call for service. |
Parts counter W2 level | After checking the parts counter in service mode, replace any part whose counter is nearing the error value. После проверки датчика деталей в сервисном меню, замените деталь, указанную в ошибке. |
|
| GARO W1221 | 01341221-1030 | GARO (image mode): Unknown command | Verify the transmitted data before reprinting. Проверьте загруженные данные перед повтором печати. |
| GARO W1222 | 01341222-1031 | GARO (image mode): Invalid parameter count (no parameters) | |
| GARO W1223 | 01341223-1032 | GARO (image mode): Required parameter missing | |
| GARO W1225 | 01341225-1034 | GARO (image mode): Other warning | |
| GARO W1226 | 01341226-103A | GARO (image mode): Image processing table error | |
| GARO W1231 | 01341231-1035 | GARO (setup): Unknown command | |
| GARO W1232 | 01341232-1036 | GARO (setup): Invalid parameter count | |
| GARO W1233 | 01341233-1037 | GARO (setup): Required parameter missing | |
| GARO W1234 | 01341234-1038 | GARO (setup): Data out of bounds | |
| GARO W1235 | 01341235-1039 | GARO (setup): Other warning | |
| End of paper feed. Cannot feed paper more. | Forced feed limit | Check the remaining quantity of roll media. Проверьте количество бумаги. |
|
| This type of paper is not compatible with HP-GL/2. | 01860006-1015 | Non-support paper of HP-GL/2 | Замените бумагу на совместимую. Exchange for the compatible paper to HP-GL/2. |
| GL2:W0501 The memory is full. |
01340501-1040 | Memory full (HP-GL/2) | Проверьте, нет ли области печати без изображения. Проверьте загруженные данные перед повтором запуска печати. Check if there is the non-image area of the print. Verify the transmitted data before reprinting. |
| GL2:W0904 The memory is full. |
01340904-1048 | Overflow of Polygon buffer (HP-GL/2) | |
| GL2:W0903 The memory is full. |
01340903-1047 | Overflow of replot buffer (HP-GL/2) | |
| GL2:W0502 The parameter is out of range. |
01340502-1041 | Invalid parameter (HP-GL/2) | Проверьте загруженные данные перед повтором печати. Verify the transmitted data before reprinting. |
| GL2:W0504 This command is not supported. |
01340504-1043 | Invalid command (HP-GL/2) | |
| Mail box nearly full. Delete unwanted data |
011A1001-2901 | The free hard disk space left for Personal Boxes in the printer’s hard disk does not have more than 1 GB, combined. | Удалите ненужные задания в личных блоках заданий. Delete unneeded jobs stored in Personal Boxes. |
| Mail box full. Now printing without saving data. |
01861003-2902 | 100 jobs are stored in the Personal Box. | Удалите ненужные задания в личных блоках заданий. Delete unneeded jobs stored in Personal Boxs. |
| Not much ink is left. Prepare to replace the ink. |
01810103-1003 | C ink tank near-empty | Замените синий картридж. Renew the C ink tank |
| Not much ink is left. Prepare to replace the ink. |
01810102-1002 | M ink tank near-empty | Замените пурпурный картридж Renew the M ink tank. |
| Not much ink is left. Prepare to replace the ink. |
01810101-1001 | Y ink tank near-empty | Замените желтый картридж. Renew the Y ink tank. |
| Not much ink is left. Prepare to replace the ink. |
01810106-1006 | MBK ink tank near-empty | Замените матовый черный картридж. Renew the MBK ink tank. |
| Not much ink is left. Prepare to replace the ink. |
01810104-1000 | BK ink tank near-empty | Замените фото-черный картридж. Renew the BK ink tank. |
| Ink tank is empty. Replace the ink tank. |
01810303-1403 | C ink tank empty | Замените синий картридж. Renew the C ink tank. |
| Ink tank is empty. Replace the ink tank. |
01810302-1402 | M ink tank empty | Замените пурпурный картридж. Renew the M ink tank. |
| Ink tank is empty. Replace the ink tank. |
01810301-1401 | Y ink tank empty | Замените желтый картридж. Renew the Y ink tank. |
| Ink tank is empty. Replace the ink tank. |
01810306-1406 | MBK ink tank empty | Замените матовый черный картридж. Renew the MBK ink tank. |
| Ink tank is empty. Replace the ink tank. |
01810304-1400 | BK ink tank empty | Замените фото-черный картридж. Renew the BK ink tank. |
| No ink tank loaded. Check ink tank. |
01810103-1413 | C ink tank removal | Вставьте синий картридж. Attach the C ink tank. |
| No ink tank loaded. Check ink tank. |
01810102-1412 | M ink tank removal | Вставьте пурпурный картридж. Attach the M ink tank. |
| No ink tank loaded. Check ink tank. |
01810101-1411 | Y ink tank removal | Вставьте желтый картридж. Attach the Y ink tank. |
| No ink tank loaded. Check ink tank. |
01810106-1416 | MBK ink tank removal | Вставьте матовый черный картридж. Attach the MBK ink tank. |
| No ink tank loaded. Check ink tank. |
01810104-1410 | BK ink tank removal | Вставьте фото-черный картридж. Attach the BK ink tank. |
| The paper is too small. | 013200D2-1051 | Size clip error | Проверьте формат загруженной бумаги. Замените бумагу. Check the media size check. Change the media size. |
| Maximum jobs stored. Delete unwanted data. |
011A1006-2907 | Saved jobs exceed the Personal Box capacity. | Нажмите кнопку “стоп” чтобы отменить задание. Удалите задания из очереди. Удалите ненужные задания, хранящиеся на жестком диске. Press the stop button to cancel the print job. Delete print jobs from the queue. Delete unneeded jobs stored on the hard disk. |
| PHead needs cleaning. Press Online to clear error. |
03800500-280C | Printhead found to have many non-discharging nozzles during a non-discharging inspection (printing paused) | Очистите печатающую головку. Проверьте состояние дюз через сервисное меню. Замение печатающую головку. Clean the printhead. Identify the nozzles in a nozzle check pattern. Replace the printhead. |
| Paper size not detected. Lift the release lever and reload the paper. |
03010000-200C | Unable to detect the leading end of paper | Проверьте край бумаги. Перезагрузите бумагу. Check the leading end of paper. Reload the paper. |
| Leading edge detection error. Lift the release lever and align leading edge with orange line. |
03010000-200D | Unable to detect the trailing end of cut sheet | Проверьте длину листа. Проверьте, нет ли замятия. Check the sheet length. Check to see if paper has not jammed. |
| Paper size not detected. Lift the release lever and reload the paper. |
03010000-2017 | Paper (right) edge detection error | Проверьте правый край бумаги. Выберите верный тип бумаги. Check the right edge of paper. Check the paper type. |
| Paper size not detected. Lift the release lever and reload the paper. |
03010000-2018 | Paper (left) edge detection error | Проверьте левый край бумаги. Выберите правильный тип бумаги. Check the left edge of paper. Check the paper type. |
| Cannot adjust printhead. Press Online to clear the error and readjust printhead. |
03863000-2820 | Printhead registration unadjustable | Проверьте бумагу на отсутствие пятен. Проверьте, нет попадает ли солнечный свет на отпечаток. Прочистите печатающую головку. Check the paper on which a pattern is printed for smears. Check the environment for interferences from outside light. Clean the printhead. |
| Cannot adjust printhead. Press Online to clear the error and readjust printhead. |
03863000-2821 | LF unadjustable | Проверьте бумагу на отсутствие пятен. Проверьте, нет попадает ли солнечный свет на отпечаток. Прочистите печатающую головку. Check the paper on which a pattern is printed for smears. Check the environment for interferences from outside light. Clean the printhead. |
| Cannot print as specified. Lift the release lever and replace paper with A4/ LTR (vertical) or larger. |
03010000-2E1F | Undersized paper loaded for internal printing (A4 or larger) | Замените бумагу на формат A4/Letter или любую большего формата. Replace with A4/Letter or any larger-sized paper. |
| Cannot print as specified. Lift the release lever and replace paper with A3/ Ledger (vertical) or larger. |
03010000-2E1F | Undersized paper loaded for internal printing (A3 or larger) | Замените бумагу на формат A3/11″x17″ или любую большего формата. Replace with A3/11″x17″ or any larger-sized paper. |
| Cannot print as specified. Lift the release lever and replace roll with 10 in. wide or larger roll. |
03010000-2E1F | Undersized paper loaded for internal printing (roll media) | Замените бумагу на рулон шириной не меньше 10 дюймов. Replace with roll media at least 10 inches in width. |
| Cannot detect paper Remove paper and press Load/Eject. |
03010000-2E25 | Paper jam while feeding/ejecting/printing | Устраните замятие и перезагрузите бумагу. Remove the paper jam and reload the paper. |
| Cannot feed paper Lift the release lever and reload paper. |
03010000-2E27 | Paper jam during feeding/printing/ejection | Перезагрузите бумагу. Reload the paper. |
| This paper cannot be used. Check supported paper sizes. |
03010000-200E | Undersized paper (cut sheets/roll media) | Замените бумагу на больший формат. Replace with larger-sized paper. |
| This paper cannot be used. Check supported paper sizes. |
03010000-200F | Oversized paper (cut sheets/roll media) | Замените бумагу на меньший формат. Replace with smaller-sized paper. |
| Use another paper. Press Online to clear the error. |
03010000-2F33 | Unadjustable because of transparent media | Замените бумагу на совместимую. Replace with adjustable media. |
| Paper loaded askew. Lift the release lever. |
03016000-2010 | Skew | Исправьте наклон бумаги и перезагрузите ее. Correct the skew in the paper and reload it. |
| Paper size not detected. Reload paper. |
03010000-200A | Unable to detect the paper width (Paper loaded at an improper position) | Перезагрузите бумагу. Reload the paper |
| Paper jam. Press Load/Eject and reload the paper. |
03010000-2E27 | Paper jam during feeding/printing/ejection | Перезагрузите бумагу. Reload the paper |
| Paper size not detected. Lift the release lever and reload the paper. |
03010000-200C | Roll media loading size detection failure | Перезагрузите рулонный носитель. Reload the roll media. |
| Cannot adjust eccentric. Press Online to clear the error. |
03863000-2822 | Eccentricity correction disabled | Проверьте, нет ли замятия бумаги. Check to see if paper has not jammed. |
| Sheet printing is selected. Press Load/Eject and load sheets. |
03860002-2E02 | Data with a cut sheet specification has been received but no cut sheets are loaded. | Загрузите листы бумаги в лоток. Load cut sheets at the paper tray port. |
| Roll printing is selected, but sheets are loaded. Press OK, remove the sheets, and load a roll. |
03860002-2E0A | Data with a roll media specification has been received when a cut sheet tray is loaded. | Замените рулонный носитель. Replace with roll media. |
| Roll printing is selected. Press Load/Eject and load a roll. |
03060A00-2E00 | Data with a roll media specification has been received but no roll media are loaded. | Загрузите рулонный носитель. Load roll media. |
| No Roll Feed Unit. Turn printer off and install roll feed unit. |
03060A00-2E0E | Roll media unit not installed | Загрузите рулонный носитель. Install the roll media unit. |
| The roll is empty. Lift the release lever and replace the roll. |
03060A00-2E1B | Roll media end | Загрузите новый рулон. Renew the supply of roll media. |
| Wrong paper feed slot for this paper type. Press Load/Eject and reload the paper. |
03061000-2E15 | Paper type mismatch | Проверьте тип бумаги и перезагрузите ее. Check the type of paper that can be fed and reload the paper. |
| Manual printing is selected, but a roll is loaded. Press Load/Eject and remove the roll. |
03860001-2E0C | Data with a cut sheet specification has been received when roll media are loaded. | Загрузите листы бумаги в лоток. Load cut sheets at the paper tray port. |
| Hardware error. 03130031-2E23 Turn off printer, wait, then turn on again. |
03130031-2E23 | Cutter unit failure | Проверьте резак. Check the cutter unit. |
| Hardware error. 03130031-2E14 Turn off printer, wait, then turn on again. |
03130031-2F14 | Writing to the ASIC register disabled | Замените главную плату контроллера. Replace the main controller PCB |
| Hardware error. 03130031-2E16 Turn off printer, wait, then turn on again. |
03130031-2F16 | Mist fan error | Проверьте вентилятор. Check the mist fan. |
| Hardware error. 03130031-2E17 Turn off printer, wait, then turn on again. |
03130031-2F17 | Suction fan lock detection error | Проверьте всасывающий вентилятор. Check the suction fan. |
| Hardware error. 03130031-2E20 Turn off printer, wait, then turn on again. |
03130031-2F20 | Purge motor cam position error | Проверьте блок очистки. Check the purge unit. |
| Hardware error. 03130031-2E22 Turn off printer, wait, then turn on again. |
03130031-2F22 | Pump travel timeout | Проверьте блок очистки. Check the purge unit. |
| Hardware error. 03130031-2E23 Turn off printer, wait, then turn on again. |
03130031-2F23 | Purge motor error Pump inoperable | Проверьте блок очистки. Check the purge unit. |
| Hardware error. 03130031-2E25 Turn off printer, wait, then turn on again. |
03130031-2F25 | Unable to detect the carriage motor home position | Проверьте каретку. Проверьте датчики на наличие пятен. Check the carriage unit. Check the linear encoder for smears. |
| Hardware error. 03130031-2E26 Turn off printer, wait, then turn on again. |
03130031-2F26 | Carriage inoperable | Проверьте каретку и окружающие ее части. Check the carriage unit and surrounding parts. |
| Hardware error. 03130031-2E27 Turn off printer, wait, then turn on again. |
03130031-2F27 | Carriage travel timeout | Проверьте каретку и окружающие ее части. Check the carriage unit and surrounding parts. |
| Hardware error. 03130031-2E1F Turn off printer, wait, then turn on again. |
03130031-2F1F | Pump cam sensor error | Проверьте блок очистки. Check the purge unit. |
| Hardware error. 03130031-2E2A Turn off printer, wait, then turn on again. |
03130031-2F2A | Unable to detect the feed roller home position | Проверьте датчики ролика подачи бумаги и окружающие его части. Проверьте, не замята ли бумага. Check the feed roller encoder and surrounding part. Check to see if paper has not jammed. |
| Hardware error. 03130031-2E29 Turn off printer, wait, then turn on again. |
03010000-2F29 | Feed motor timeout (Roll media) | Проверьте ролик подачи бумаги. Проверьте рулон бумаги. Проверьте, нет ли замятия бумаги. Check the roll feed unit. Check roll media. Check to see if paper has not jammed in the printer. |
| Hardware error. 03130031-2E2E Turn off printer, wait, then turn on again. |
03130031-2F2E | Roll travel timeout | Проверьте ролик подачи бумаги. Check the roll feed unit. |
| Hardware error. 03130031-4027 Turn off printer, wait, then turn on again. |
03130031-4027 | Lift travel timeout error | Проверьте каретку и окружающие ее части. Check the carriage unit and surrounding parts. |
| Hardware error. 03130031-2E13 Turn off printer, wait, then turn on again. |
03130031-2F13 | A/D converter external trigger output stop detection hardware error 1 | Попробуйте очистить ленту энкодера, а также очистите направляющую каретки. Эта ошибка распространена на широкоформатных принтерах Canon и обычно устраняется путем очистки направляющей и ленты. Направляющая каретки (рельс) должен быть сухим.Если это не поможет – нужно менять печатающую голову. |
| Hardware error. 03130031-2F32 Turn off printer, wait, then turn on again. |
03130031-2F32 | Multi sensor error | Проверьте, не попадает ли свет на устройство. Замените мультисенсорный блок. Check the environment for interferences from outside light. Replace the multi sensor unit. |
| Hardware error. 03130031-2F3A Turn off printer, wait, then turn on again. |
03130031-2F3A | Valve motor error | Проверьте блок подачи чернил. Check the ink supply unit. |
| Hardware error. 03130031-2F3B Turn off printer, wait, then turn on again. |
03130031-2F3B | CS communication error | Вытащите чернильные картриджи, затем снова вставьте их. Проверьте главную плату контроллера. Remove the ink tanks and then reload them. Check the main controller PCB. |
| Hardware error. 03130031-2F70 Turn off printer, wait, then turn on again. |
03130031-2F70 | Ошибка заполнения промежуточных чернильных ёмкостей. | Как устранить |
| Hardware error. 03130031-2F71 Turn off printer, wait, then turn on again. |
03130031-2F71 | Ошибка заполнения промежуточной чернильной ёмкости (левой). | Как устранить |
| Hardware error. 03130031-2F72 Turn off printer, wait, then turn on again. |
03130031-2F72 | Ошибка заполнения промежуточной чернильной ёмкости (правой). | Как устранить |
| Hardware error. 03130031-260E Turn off printer, wait, then turn on again. |
03130031-260E | Gap detection error | Проверьте каретку и окружающие ее части. Замените главную плату контроллера. Check the carriage unit and surrounding parts. Replace the main controller PCB. |
| Hardware error. 03130031-2618 Turn off printer, wait, then turn on again. |
03130031-2618 | VH voltage error | Проверьте блок питания. Check the power supply unit. |
| Hardware error. 03130031-260F Turn off printer, wait, then turn on again. |
03130031-260F | Gap reference surface error | Replace the reference surface sheet. |
| Roll feed unit error Turn off printer and check roll feed unit |
03060B00-2E24 | Roll feed unit failure | Замените блок подачи рулона. Replace the roll feed unit. |
| Unknown file. Check file format. Turn off printer, wait a while, then turn it on again. |
03900001-4049 | ROM data for another model has been transferred. | Загрузите верные данные. Transmit valid ROM data. |
| Unknown file. Check file format. Turn off printer, wait a while, then turn it on again. |
03900001-4042 | MIT data transfer failure | Проверьте данные перед загрузкой. Verify the validity of MID data before transferring it. |
| Hardware error. 03130031-2F2B Turn off printer, wait, then turn on again. |
03130031-2F2B | LF operation failure | Проверьте, не застряла ли бумага. Проверьте двигатель подачи и ролик подачи.Check to see if paper has not jammed. Check the feed motor and feed roller. |
| Printhead error Open top cover and replace the printhead. |
03800200-2802 | Invalid printhead installed | Замените печатающую головку. Replace printhead |
| Printhead error Open top cover and replace the right printhead. |
03800300-2801 | Printhead DI compensation failure | Замените печатающую головку. Replace printhead |
| Printhead error Open top cover and replace the right printhead. |
03800400-2803 | Printhead EEPROM error | Замените печатающую головку. Replace printhead |
| Hardware error. 03800500-2F40 Turn off printer, wait, then turn on again. |
03800500-2F40 | The non-discharge of all colors and chips(A/B, EVEN/ODD) and nozzles is detected (проблема с поступлением чернил в/из печатающей головки.) | Проверьте трубки для чернил и окружающие детали. Проверьте блок очистки печатающей головки и окружающие детали. Проверьте датчик управления головкой и окружающие детали. Убедитесь, что печатающая головка установлена правильно. Если визуально все чисто и корректно подключено, нужно пробовать: Заменить датчик управления головкой. Заменить главную плату контроллера. Замените печатающую головку. Замените каретку. |
| Hardware error. 03800500-2F2F Turn off printer, wait, then turn on again. |
03800500-2F2F | Non-discharging error | Проверьте датчик управления печатающей головкой. Замените датчик управления печатающей головкой. Замените печатающую головку. Identify the head management sensor unit Replace the head management sensor unit Replace the printhead |
| Hardware error. 03800500-2F30 Turn off printer, wait, then turn on again. |
03800500-2F30 | Non-discharging position adjustment error | Проверьте датчик управления печатающей головкой. Замените датчик управления печатающей головкой. Замените печатающую головку. Identify the head management sensor unit Replace the head management sensor unit Replace the printhead |
| Ink tank is empty. Press OK and replace ink tank. |
03810104-2500 | Bk ink tank empty | Замените картридж BK Renew the Bk ink tank |
| Ink tank is empty. Press OK and replace ink tank. |
03810101-2501 | Y ink tank empty | Замените картридж Y. Renew the Y ink tank |
| Ink tank is empty. Press OK and replace ink tank. |
03810102-2502 | M ink tank empty | Замените картридж M. Renew the M ink tank |
| Ink tank is empty. Press OK and replace ink tank. |
03810103-2503 | C ink tank empty | Замените картридж C. Renew the C ink tank |
| Ink tank is empty. Press OK and replace ink tank. |
03810106-2506 | MBk ink tank empty | Замените картридж MBK. Renew the MBk ink tank |
| Ink tank is empty. Press OK and replace ink tank. |
03810106-2507 | MBk2 ink tank empty | Замените картридж MBK. Renew the MBk ink tank |
| Ink insufficient. Press OK and replace ink tank. |
03810204-2580 | Low on the Bk ink tank (as during cleaning) | Замените на заполненный картридж BK Replace with a fully replenished Bk ink tank |
| Ink insufficient. Press OK and replace ink tank. |
03810201-2581 | Low on the Y ink tank (as during cleaning) | Замените на заполненный картридж Y Replace with a fully replenished Y ink tank |
| Ink insufficient. Press OK and replace ink tank. |
03810202-2582 | Low on the M ink tank (as during cleaning) | Замените на заполненный картридж M Replace with a fully replenished M ink tank |
| Ink insufficient. Press OK and replace ink tank. |
03810203-2583 | Low on the C ink tank (as during cleaning) | Замените на заполненный картридж C Replace with a fully replenished C ink tank |
| Ink insufficient. Press OK and replace ink tank. |
03810206-2586 | Low on the MBk ink tank (as during cleaning) | Замените на заполненный картридж MBK Replace with a fully replenished MBk ink tank |
| Ink insufficient. Press OK and replace ink tank. |
03810204-2590 | Low on the Bk ink tank (during pre-printing checks) | Замените на заполненный картридж BK Replace with a fully replenished Bk ink tank |
| Ink insufficient. Press OK and replace ink tank. |
03810201-2591 | Low on the Y ink tank (during pre-printing checks) | Замените на заполненный картридж Y Replace with a fully replenished Y ink tank |
| Ink insufficient. Press OK and replace ink tank. |
03810202-2592 | Low on the M ink tank (during pre-printing checks) | Замените на заполненный картридж M Replace with a fully replenished M ink tank |
| Ink insufficient. Press OK and replace ink tank. |
03810203-2593 | Low on the C ink tank (during pre-printing checks) | Замените на заполненный картридж C Replace with a fully replenished C ink tank |
| Ink insufficient. Press OK and replace ink tank. |
03810206-2596 | Low on the MBk ink tank (during pre-printing checks) | Замените на заполненный картридж MBK Replace with a fully replenished MBk ink tank |
| Ink tank error. Press OK and replace ink tank. |
03830204-2540 | Bk ink tank ID error | Замените картридж BK на подходящий. Replace with a valid Bk ink tank |
| Ink tank error. Press OK and replace ink tank. |
03830201-2541 | Y ink tank ID error | Замените картридж Y на подходящий. Replace with a valid Y ink tank |
| Ink tank error. Press OK and replace ink tank. |
03830202-2542 | M ink tank ID error | Замените картридж M на подходящий Replace with a valid M ink tank |
| Ink tank error. Press OK and replace ink tank. |
03830203-2543 | C ink tank ID error | Замените картридж C на подходящий. Replace with a valid C ink tank |
| Ink tank error. Press OK and replace ink tank. |
03830206-2546 | MBk ink tank ID error | Замените картридж MBK на подходящий. Replace with a valid MBk ink tank |
| Ink tank error. Press OK and replace ink tank. |
03830206-2547 | MBk2 ink tank ID error | Замените картридж MBK на подходящий. Replace with a valid MBk ink tank |
| No ink tank loaded. Press OK and check ink tank. |
03830104-2520 | BK ink tank not installed | Установите картридж BK. Install a Bk ink tank |
| No ink tank loaded. Press OK and check ink tank. |
03830101-2521 | Y ink tank not installed | Установите картридж Y. Install a Y ink tank |
| No ink tank loaded. Press OK and check ink tank. |
03830102-2522 | M ink tank not installed | Установите картридж M. Install a M ink tank |
| No ink tank loaded. Press OK and check ink tank. |
03830103-2523 | C ink tank not installed | Установить картридж C. Install a C ink tank |
| No ink tank loaded. Press OK and check ink tank. |
03830106-2526 | MBK ink tank not installed | Установите картридж MBK. Install a MBk ink tank |
| No ink tank loaded. Press OK and check ink tank. |
03830106-2527 | MBK2 ink tank not installed | Установите картридж MBK. Install a MBk ink tank |
| Top cover is open. Turn off printer, wait a while, and turn it on again. |
03031000-2F38 | Top cover abnormally open | Закройте верхнюю крышку и включите принтер заново. Close the top cover and turn on the printer again. |
| Ink tank cover is open. Turn off printer, wait a while, and turn it on again. |
03031000-2E10 | Ink tank cover abnormally open | Закройте крышку картриджного отсека и заново включите принтер. Close the ink tank cover and turn on the printer again. |
| Maintenance cartridge full. Replace the maintenance cartridge. |
03841001-2819 | Maintenance cartridge full | Замените картридж обслуживания. Renew the maintenance cartridge. |
| No Maintenance Cartridge capacity. Replace the maintenance cartridge. |
03841001-281B | Not enough space in the maintenance cartridge prior to cleaning | Замените картридж обслуживания. Replace the maintenance cartridge. |
| Maintenance cartridge problem. Replace the maintenance cartridge. |
03841201-2816 | Maintenance cartridge EEPROM error | Замените картридж обслуживания. Renew the maintenance cartridge. |
| Maintenance cartridge problem. Replace the maintenance cartridge. |
03841201-2817 | Maintenance cartridge ID error | Замените картридж обслуживания. Renew the maintenance cartridge. |
| Borderless printng not possible. Check roll position. Online: Print Load/Eject: Change Paper |
03861001-2405 | Paper loaded at a position inaccessible for borderless printing | Проверьте, установлен ли ограничитель для печати без полей. Перезагрузите бумагу. Check to see if a borderless printing spacer is installed. Reload the paper. |
| Borderless printng not possible. Check paper size setting. Online: Print Load/Eject: Change Paper |
03861001-2406 | Data unfit for borderless printing | Проверьте размер бумаги. Замените бумагу. Check the paper size. Change the paper size. |
| Insufficient paper for job Online: Print Stop: Stop Printing Load/Eject: Change Paper |
03862000-2E09 | Not enough roll media on remaining roll media quantity detection | Возобновите подачу бумаги. Renew the supply of roll media. |
| Cannot cut paper. Lift the release lever and reload the paper. |
03870001-2015 | Cutting failure | Отрежьте бумагу вручную. Проверьте нож. Cut paper manually. Check the cutter. |
| Cannot adjust optic axis. Press Online to clear the error. |
03863000-2824 | Optical axis error | Проверьте мультидатчик. Проверьте датчик управления печатающей головкой. Check the multi sensor. Check the head management sensor. |
| This type of paper is not compatible with HP-GL/ 2. Online: Print Stop: Stop Printing Load/Eject: Change Paper |
03061000-2E15 | Non-support media of HP-GL/2 | Замените бумагу на совместимую с HP-GL/2. Exchange for the compatible paper to HP-GL/2 before reprinting. |
| Mail box full. Delete unwanted data on your computer to resume printing. Press Stop to cancel printing. |
031A1001-2905 | The job store executed when the free hard disk space left for Personal Boxes in the printer’s hard disk is full. | Удалите ненужные задачи из личного блока заданий. Delete unneeded jobs stored in Personal Boxes. |
| Mail box full. Cannot save. Delete unwanted data on your computer to resume printing. Press Stop to cancel printing. |
031A1006-2906 | The store executed when 32 jobs are stored in the Personal Box. | Удалите ненужные задачи из личного блока заданий. Delete unneeded jobs stored in Personal Boxes. |
| Hard disk error. Press OK to reformat |
031A1002-2908 | Hard disk format error | Нажмите кнопку ОК для форматирования жесткого диска. Когда форматирование будет завершено, принтер автоматически перезагрузится. Press the [OK] button to start reformatting the hard disk. When formatting is finished, the printer automatically restarts. |
| File read error. Turn off printer, wait a while, and turn it on again. Invalid files will be deleted. |
031A1002-2909 | Hard disk file error | Перезагрузите принтер. Только поврежденные файлы будут удалены, и принтер перезагрузится. Restart the printer. Only the corrupted files will be deleted, and the printer will restart. |
| Hardware error. 03800500-2F31 Turn off printer, wait, then turn on again. |
03800500-2F31 | Non-discharge detection optical axis error | Проверьте датчик управления печатающей головкой. Замените датчик управления печатающей головкой. Замените печатающую головку. Check the head management sensor. Replace the head management sensor. Replace the printhead. |
| Hardware error. 03130031-2F3C Turn off printer, wait, then turn on again. |
03130031-2F3C | LF pressure error | Проверьте прижимной ролик и окружающие его части. Замените узел привода прижимного ролика. Check the pinch roller and surrounding part. Replace the pinch roller pressure drive unit. |
| No printhead Install printhead. |
03800100-2800 | Printhead not installed | Установите печатающую головку. Install the printhead. |
| Wrong printhead. Open top cover and replace the printhead. | 03800200-2811 | Printhead version error | Замените печатающую головку. Replace the printhead. |
| No maintenance cartridge. Check the maintenance cartridge. |
03841101-2818 | Mauntenance cartridge not installed | Установите картридж обслуживания. Install the maintenance cartridge. |
| This type of media is not compatible with HP-GL/ 2. | 03860006-2825 | Paper type mismatch at HP-GL/2 printing | Замените бумагу на совместимую с HP-GL\2 перед возобновлением печати. Exchange for the compatible paper to HP-GL/2 before reprinting. |
| Cannot cut paper. Lift the release lever and reload the paper. |
03870001-2019 | Cut failure (during jam occure) | Проверьте резак и окружающие его части. Замените резак. Check the cutter unit and surrounding part. Replace the cutter. |
| Insufficient paper for job | 03862001-2E31 | Not enough roll media | Возобновите подачу бумаги. Renew the supply of roll media. |
| Paper jam. Manually rewind roll all the way and press OK. |
03010000-2E3A | Madia load failure | Проверьте блок захвата и подачи бумаги. Проверьте, нет ли замятия бумаги. Check the pick-up unit and roll media. Check to see if paper has not jammed. |
| Sheet printing is selected. Press Load/Eject and load sheets. | 03060100-2E02 | Cut sheet in not set | Загрузите листы бумаги в лоток. Load cut sheets at the paper tray port. |
| Borderless printng not possible. Check supported paper. | 03861001-2408 | Borderless printing disabled (unsupported size) | Проверьте размер носителя. Check the media size. Change the media size. |
| Borderless printng not possible. Paper stretched or shrank. Confirm usage cond. of the paper. |
03861001-2407 | Borderless printing disabled (engine detection) | Перезагрузите бумагу. Reload the paper. |
| Roll printing is selected. Press Load/Eject and load a roll. | 03060A00-2E35 | Roll media is not loaded for internal printing. | Перезагрузите рулог бумаги. Reload the roll media. |
Ошибки в сервисном режиме
| Code | Description | Action |
| E141-4046 | Number of recovery rotations reaching 50,000 or more | Замените комплект очистки, затем обновите счетчик деталей в сервисном режиме. Replace the purge kit, and then clear the parts counter in the service mode. |
| E146-4001 | Borderless/flow idle ejection/mist recovery count error | Замените блок для отработанных чернил или вентилятор тумана или поглотитель отработанных чернил или мультисенсор, а затем обновите счетчик запчастей в сервисном режиме. Replace the waste ink tank unit or mist fan or waste ink absorber or multi sensor reference, and then clear the parts counter in the service mode. |
| E161-403E | Abnormal temperature rise in printhead | Замените печатающую головку. Replace the printhead. |
| E194-404A | Non-discharging nozzle count error | Замените блок датчика управления головкой, а затем очистите счетчик деталей в сервисном режиме.Replace the head management sensor unit, and then clear the parts counter in the service mode. |
| E196-4040 | Checksum error | Замените главную плату контроллера. Replace the main controller PCB. |
| E196-4041 | Flash memory erase error | Замените главную плату контроллера. Replace the main controller PCB. |
| E196-4042 | Flash memory write error | Замените главную плату контроллера Replace the main controller PCB. |
| E196-4045 | EEPROM write error | Замените главную плату контроллера. Replace the main controller PCB. |
| E196-404C | Serial number mismatch between boards | Execute PCB replacement mode or replace the main controller PCB. |
| E196-404D | Machine ID mismatch between boards | Замените главную плату контроллера Replace the main controller PCB. |
| E196-404E | EEPROM read error | Замените главную плату контроллера. Replace the main controller PCB. |
| E198-401C | RTC error | Замените литиевую батарею или замените главную плату контроллера.Replace the lithium battery or replace the main controller PCB. |
| E198-401D | RTC low battery error | Замените литиевую батарею или замените главную плату контроллера.Replace the lithium battery or replace the main controller PCB. |
| E198-401E | RTC clock stop | Замените литиевую батарею или замените главную плату контроллера.Replace the lithium battery or replace the main controller PCB. |
| E199-404B | Temperature/humidity sensor board connector out of position | Проверьте разъем платы датчика температуры / влажности или замените плату.Check the temperature/humidity sensor board connector or replace the board. |
| E602-401A | HDD failure | Замените жесткий диск. Replace the HDD unit. |
| E602-401B | HDD connection error | Проверьте разъем жесткого диска. Замените жесткий диск. Check the HDD connector/Replace the HDD unit. |
| E144-4047 | Number of carrriage scan operation is full | Замените рулонный блок, затем обновите счетчик деталей в сервисном меню. Replace the tube unit, and then clear the parts counter in the service mode. |
| E144-4048 | Printhead ink filling failure | Замените печатающую головку. Replace the printhead. |
| E196-4043 | Memory error | Выполните обновление прошивки или замените главную плату контроллера.Execute firmware update or replace the main controller PCB. |
| E196-4044 | Firmware size error | Выполните обновление прошивки или замените главную плату контроллера.Execute firmware update or replace the main controller PCB. |