012 330 ошибка

          Во время работы с аппаратом могут возникать проблемы, связанные с неисправностями «железа» или ПО. И если расходные материалы можно просто заменить, то с «мозгами» нужно разбираться. Поэтому, для экономии времени и удобства, ниже представлены возможные коды ошибок (FAULT ERROR CODE), которые показывают Xerox DocuColor DC 240/250/242/252/260 и WorkCentre WC 7655/7665/7675/7755/7765/7775 при неисправности, и их значение:

002-770 ERROR — RAP Insufficient HDD capacity while processing the job template within a job.

003-318 ERROR — RAP IIT software failure.

003-319 ERROR — RAP IIT Video Driver Detection Fail.

003-320 ERROR — RAP IIT-ESS Communication Fail 1.

003-321 ERROR — RAP IIT-ESS Communication Fail 2.

003-322 ERROR — RAP IIT-ESS Communication Fail 3.

003-323 ERROR — RAP IIT-ESS Communication Fail 4.

003-324 ERROR — RAP IIT-ESS Communication Fail 5.

003-325 ERROR — RAP IIT-ESS Communication Fail 6.

003-326 ERROR — RAP IIT-ESS Communication Fail 7.

003-327 ERROR — RAP IIT-ESS Communication Fail 8.

003-328 ERROR — RAP IIT-ESS Communication Fail 9.

003-329 ERROR — RAP IIT-ESS Communication Fail 10.

003-330 ERROR — RAP IIT-ESS Communication Fail 11.

003-331 ERROR — RAP IIT-ESS Communication Fail 12.

003-332 ERROR — RAP IIT-ESS Communication Fail 13.

003-333 ERROR — RAP IIT-ESS Communication Fail 14.

003-334 ERROR — RAP IIT-ESS Communication Fail 15.

003-335 ERROR — RAP IIT-ESS Communication Fail 16.

003-336 ERROR — RAP IIT-ESS Communication Fail 17.

003-337 ERROR — RAP IIT-ESS Communication Fail 18.

003-338 ERROR — RAP IIT-ESS Communication Fail 19.

003-339 ERROR — RAP IIT-ESS Communication Fail 20.

003-340 ERROR — RAP IIT-ESS Communication Fail 21.

003-341 ERROR — RAP IIT-ESS Communication Fail 22.

003-342 ERROR — RAP IIT-ESS Communication Fail 23.

003-343 ERROR — RAP IIT-ESS Communication Fail 24.

003-344 ERROR — RAP Power on hotline failure.

003-345 ERROR — RAP X PIO Unmatch Fail 1.

003-346 ERROR — RAP X PIO Unmatch Fail 2.

003-750 ERROR — RAP Book Duplex-Insufficient Docs.

003-751 ERROR — RAP Under PANTHER Capacity (Scan).

003-752 ERROR — RAP This status code is displayed if 600dpi cannot be scanned (DADF).

003-753 ERROR — RAP This status code is displayed if over 300dpi cannot be scanned (DADF).

003-754 ERROR — RAP S2X Recoverable Error.

003-755 ERROR — RAP S2X Command Error.

003-757 ERROR — RAP This status code is displayed if over 400dpi cannot be scanned (DADF).

003-760 ERROR — RAP Scan Settings Error.

003-761 ERROR — RAP Incorrect Paper Tray Size.

003-763 ERROR — RAP Adjustment Chart Not Found.

003-764 ERROR — RAP Adjustment Chart Not Found.

003-780 ERROR — RAP Scan Image Compression Error.

003-795 ERROR — RAP AMS Limit Error.

003-940 ERROR — RAP DAM Memory is insufficient.

003-942 ERROR — RAP Document Size Error.

003-944 ERROR — RAP Image Repeat Count Fail.

003-946 ERROR — RAP Copy Vertical/Horizontal Difference (APS).

003-947 ERROR — RAP Replaced Original Count Error.

003-948 ERROR — RAP Replaced Original Mismatch.

003-952 ERROR — RAP Return Documents Color mismatch.

003-955 ERROR — RAP Documents Size Exchange Error.

003-956 ERROR — RAP Documents Size Unknown Error.

003-963 ERROR — RAP No APS Object Tray.

003-965 ERROR — RAP ATS/APS No Paper. There is no paper in the trays that can be selected with APS.

003-966 ERROR — RAP AATS/APS No Destination Error.

003-968 ERROR — RAP Punch Position Error.

003-969 ERROR — RAP Punch Size Error.

003-972 ERROR — RAP Maximum Stored Page Over Flow.

003-973 ERROR — RAP Every Direction Difference.

003-974 ERROR — RAP Next Original Specification.

003-977 ERROR — RAP Document Miss Match (Multi Scan).

003-978 ERROR — RAP Color Document Mismatch (Multi Scan).

003-980 ERROR — RAP Staple Position Error.

003-981 ERROR — RAP Staple Size Error.

003-982 ERROR — RAP IITsc HDD Access Error.

005-121 ERROR — RAP DADF Feed Sensor ON Jam.

005-122 ERROR — RAP DADF Simplex/Side 1 Pre Reg Sensor ON Jam.

005-123 ERROR — RAP DADF Simplex/Side 1 Reg Sensor ON Jam.

005-124 ERROR — RAP DADF Lead Reg Sensor ON Jam.

005-125 ERROR — RAP DADF Reg Sensor OFF Jam.

005-126 ERROR — RAP DADF Out Sensor ON Jam.

005-127 ERROR — RAP DADF Out Sensor OFF Jam.

005-128 ERROR — RAP DADF Exit Sensor 1 ON Jam (Simplex Mode).

005-129 ERROR — RAP DADF Exit Sensor 1 OFF Jam (Simplex Mode).

005-130 ERROR — RAP DADF Invert Sensor ON Jam (Duplex Mode).

005-131 ERROR — RAP DADF Invert Sensor On Jam (Inverting).

005-132 ERROR — RAP DADF Invert SNR on Jam 2.

005-133 ERROR — RAP DADF Invert Sensor OFF Jam.

005-134 ERROR — RAP DADF Invert SNR off Jam (Inv).

005-135 ERROR — RAP DADF Pre Reg Sensor ON Jam (Invert).

005-136 ERROR — ERROR — RAP DADF Reg Sensor ON Jam (Invert).

005-137 ERROR — RAP DADF Exit Sensor 2 ON Jam.

005-138 ERROR — RAP DADF Exit Sensor 1 ON Jam.

005-139 ERROR — RAP DADF Invert SNR off Jam.

005-141 ERROR — RAP DADF Feed Sensor OFF Jam.

005-142 ERROR — RAP DADF Exit Sensor 1 OFF Jam (Duplex Mode).

005-143 ERROR — RAP DADF Exit Sensor 2 OFF Jam.

005-144 ERROR — RAP DADF Too First Pre Reg Sensor ON Jam.

005-145 ERROR — RAP DADF Reg Sensor Off Jam (Invert).

005-146 ERROR — RAP DADF Pre Reg Sensor Off Jam.

005-147 ERROR — RAP DADF Pre Reg Sensor Off Jam (Invert).

005-150 ERROR — RAP DADF Feed Sensor OFF Jam (Perforated Original Mode).

005-151 ERROR — RAP DADF Pre Reg Sensor OFF Jam (Perforated Original Mode).

005-152 ERROR — RAP DADF Reg Sensor OFF Jam (Perforated Original Mode).

005-153 ERROR — RAP DADF Reg Sensor OFF Jam (Perforated Original Mode).

005-154 ERROR — RAP DADF Out Sensor OFF Jam (Perforated Original Mode).

005-155 ERROR — RAP DADF Exit Sensor 1 OFF Jam (Perforated Original Mode) (Simplex).

005-156 ERROR — RAP DADF Exit Sensor 1 OFF Jam (Perforated Original Mode) (Duplex).

005-157 ERROR — RAP DADF Invert Sensor OFF Jam (Perforated Original Mode).

005-158 ERROR — RAP DADF Exit Sensor 2 OFF Jam (Perforated Original Mode).

005-160 ERROR — RAP DADF Tray Lift Up Fail (Document Set) (Within Job).

005-190 ERROR — RAP DADF Feed Motor Logic Jam.

005-194 ERROR — RAP Size Mismatch Jam on Slow Scan Mix Size.

005-195 ERROR — RAP Size Mismatch Jam on No Mix Size.

005-196 ERROR — RAP Size Mismatch Jam on No Mix Size.

005-197 ERROR — RAP Prohibit Combine Size Jam.

005-198 ERROR — RAP Too Short Size Jam.

005-199 ERROR — RAP Too Long Size Jam.

005-275 ERROR — RAP DADF RAM Fail.

005-280 ERROR — RAP DADF EEPROM Fail.

005-282 ERROR — RAP DADF Tray Lift Up Fail (No Document).

005-283 ERROR — RAP DADF Stack Height Sensor Logic Fail.

005-284 ERROR — RAP DADF APS Sensor Logic Fail.

005-285 ERROR — RAP DADF Nudger Lift Up Fail.

005-286 ERROR — RAP DADF Feed Out Sensor Fail.

005-303 ERROR — RAP DADF Tray Interlock is open.

005-304 ERROR — RAP Platen Interlock Open.

005-305 ERROR — RAP DADF Feeder Cover Interlock Open (Run).

005-306 ERROR — RAP DADF Tray Interlock Open (Run).

005-308 ERROR — RAP The DADF L/H Cover Interlock is open.

005-309 ERROR — RAP DADF L/H Cover Interlock Open (Run).

005-906 ERROR — RAP DADF Feed Sensor Static Jam.

005-907 ERROR — RAP DADF Pre Reg Sensor Static Jam.

005-908 ERROR — RAP DADF Reg Sensor Static Jam.

005-909 ERROR — RAP DADF Lead Reg Sensor Static Jam..

005-910 ERROR — RAP DADF Out Sensor Static Jam.

005-911 ERROR — RAP DADF Exit Sensor 1 Static Jam.

005-912 ERROR — RAP DADF Exit Sensor 2 Static Jam.

005-913 ERROR — RAP DADF Invert Sensor Static Jam.

005-914 ERROR — RAP DADF No. 1/2/3 APS Sensor Static Jam.

005-915 ERROR — RAP DADF No. 1 APS Sensor Static Jam.

005-916 ERROR — RAP DADF No. 2 APS Sensor Static Jam.

005-917 ERROR — RAP DADF No. 3 APS Sensor Static Jam.

005-918 ERROR — RAP DADF Invert Sensor 2 Static Jam.

005-919 ERROR — RAP DADF Tray Lift Up Fail (Document Set).

005-940 ERROR — RAP DADF No Original Fail.

005-941 ERROR — RAP DADF Not Enough Document.

005-942 ERROR — RAP DADF Tray Stack Over Fail.

010-311 ERROR — RAP Fuser Heat Roll STS-1 Disconnection Fail. It was detected that fuser heat roll STS-1 disconnected.

010-319 ERROR — RAP Fuser NC Sensor Differential Amp Fail.

010-320 ERROR — RAP Heat Roll Over Heat Fail.

010-321 ERROR — RAP Fuser Nip Fail.

010-322 ERROR — RAP Fuser NC Center Sensor Disconnection Fail. (Fuser Temperature Sensor Fail).

010-323 ERROR — RAP Fuser Rear Sensor Disconnection Fail. (Fuser Temperature Sensor Fail).

010-324 ERROR — RAP Fuser NVM Fail.

010-326 ERROR — RAP Wait Heat Roll Fuser On Time Fail.

010-327 ERROR — RAP Standby Heat Roll Fuser On Time Fail.

010-330 ERROR — RAP Fuser Motor Fail.

010-420 ERROR — RAP Fuser Assembly Life Near End.

010-421 ERROR — RAP Fuser Assembly Life End.

012-112 ERROR — RAP Finisher Interface Entrance Sensor ON.

012-113 ERROR — RAP Booklet In Sensor ON Jam.

012-114 ERROR — RAP Booklet In Sensor OFF Jam.

012-115 ERROR — RAP Booklet Folder Roll Exit Sensor ON Jam.

012-125 ERROR — RAP Gate Sensor ON JAM: Finisher.

012-132 ERROR — RAP Finisher Transport Entrance Sensor ON Jam (Long).

012-142 ERROR — RAP Buffer Path Sensor ON Jam A.

012-151 ERROR — RAP Compile Exit Sensor OFF Jam.

012-152 ERROR — RAP Compile Exit Sensor ON Jam A.

012-161 ERROR — RAP Set Eject Jam.

012-162 ERROR — RAP Finisher Interface EXIT. Sensor ON Jam.

012-171 ERROR — RAP Top Tray Exit Sensor ON Jam A.

012-172 ERROR — RAP Top Tray Exit Sensor OFF Jam A.

012-180 ERROR — RAP Booklet Folder Roll Exit Sensor OFF Jam.

012-211 ERROR — RAP Stacker Tray Fail.

012-212 ERROR — RAP Stacker Tray Upper Limit Fail.

012-213 ERROR — RAP Stacker Tray Lower Limit Fail.

012-221 ERROR — RAP Tamper Home Sensor ON Fail.

012-223 ERROR — RAP Tamper Home Sensor OFF Fail.

012-224 ERROR — RAP Rear Tamper Home Sensor OFF Fail.

012-225 ERROR — RAP Booklet Tamper F Home Sensor ON Fail.

012-226 ERROR — RAP Booklet Tamper F Home Sensor OFF Fail.

012-227 ERROR — RAP Booklet End Guide Home Sensor OFF Fail.

012-228 ERROR — RAP Booklet End Guide Home Sensor ON Fail.

012-229 ERROR — RAP Booklet Tamper R Home Sensor ON Fail.

012-230 ERROR — RAP Booklet Tamper R Home Sensor OFF Fail.

012-243 ERROR — RAP Booklet Knife Home Sensor ON Fail.

012-246 ERROR — RAP Booklet Stapler Fail.

012-247 ERROR — RAP Side Regi Sensor OFF Fail.

012-260 ERROR — RAP Eject Clamp Up Sensor ON Fail.

012-261 ERROR — RAP Booklet Knife Folding SNR Fail.

012-263 ERROR — RAP Finisher Rear Tamper Home Sensor ON.

012-264 ERROR — RAP Booklet Drawer Broken Fail.

012-265 ERROR — RAP Booklet Knife Home Sensor OFF Fail.

012-266 ERROR — RAP Booklet Compiler No Paper Sensor Fail.

012-270 ERROR — RAP Top Offset Home Sensor ON Fail: Finisher.

012-271 ERROR — RAP Top Offset Home Sensor OFF Fail: Finisher.

012-282 ERROR — RAP Eject Clamp Up Sensor OFF Fail.

012-283 ERROR — RAP Finisher Set Clamp Home Sensor ON Fail.

012-284 ERROR — RAP Finisher Set Clamp Home Sensor OFF Fail.

012-291 ERROR — RAP Stapler Fail.

012-295 ERROR — RAP Finisher Stapler Move Sensor On Fail.

012-296 ERROR — RAP Finisher Stapler Move Sensor OFF Fail.

012-300 ERROR — RAP Finisher Eject Cover Open (Compiler Cover).

012-302 ERROR — RAP Finisher Front Door Interlock Open.

012-307 ERROR — RAP Booklet Drawer Set Fail.

012-320 ERROR — RAP Punch Home Sensor ON Fail.

012-321 ERROR — RAP Punch Home Sensor OFF Fail.

012-322 ERROR — RAP Puncher Move Home Sensor OFF Fail.

012-323 ERROR — RAP Puncher Move Home Sensor On Fail.

012-325 ERROR — RAP Side Regi Home Sensor On Fail.

012-330 ERROR — RAP Decurler Cam Home Sensor OFF Fail.

012-332 ERROR — RAP Decurler Cam Home Sensor ON Fail.

012-334 ERROR — RAP Download Mode Fail.

012-335 ERROR — RAP Booklet Sub CPU Communication Fail.

012-900 ERROR — RAP Buffer Path Sensor Static Jam.

012-901 ERROR — RAP Finisher Paper Remains at H-Transport Entrance.

012-902 ERROR — RAP Finisher Paper Remains H-Transport Exit.

012-903 ERROR — RAP Compile Exit Sensor Static Jam.

012-905 ERROR — RAP Compile Tray No Paper Sensor Static Jam.

012-907 ERROR — RAP Top Tray Exit Sensor Static Jam.

012-920 ERROR — RAP Gate Sensor static JAM (to Top Tray) A: Finisher.

012-932 ERROR — RAP Gate SNR static JAM (to Stacker Tray) A.

012-934 ERROR — RAP Gate SNR static JAM (to Stacker Tray) C.

012-935 ERROR — RAP Finisher Paper Remains at Transport Entrance Sensor.

012-936 ERROR — RAP Paper Remain at Booklet In SNR A.

012-949 ERROR — RAP Finisher Punch DustBox Miss Set.

013-902 ERROR — RAP Booklet Compile No Paper Sensor Static Jam.

013-903 ERROR — RAP Booklet Folder Roll Exit Sensor Static Jam.

016-210 ERROR — RAP Software Option Fail (HDD Not Exist).

016-211 ERROR — RAP Software Option Fail (System Memory Low Volume).

016-212 ERROR — RAP SW Option Fail (Page Memory Low).

016-213 ERROR — RAP SW Option Fail (Printer CARD Not Exist).

016-215 ERROR — RAP SW Option Fail (JPEG Board Not Exist).

016-216 ERROR — RAP SW Option Fail (Ext Memory Not Exist).

016-217 ERROR — RAP SW Option Fail (Controller ROM not Printer kit).

016-218 ERROR — RAP Because PS Kit is not installed, XDOD functions cannot be fulfilled.

016-219 ERROR — RAP License is required (Printer Kit).

016-220 ERROR — RAP S2X Unrecoverable Error.

016-221 ERROR — RAP S2X Communication Error.

016-222 ERROR — RAP S2X Self-Diag Error.

016-223 ERROR — RAP SS2X SDRAM Error.

016-224 ERROR — RAP S2X PCI Reg Error.

016-225 ERROR — RAP S2X ROM CheckSum Error.

016-226 ERROR — RAP S2X IIT Connection Error.

016-227 ERROR — RAP S2X DDR Error.

016-228 ERROR — RAP S2X Image Processing Error.

016-229 ERROR — RAP SW Option Fail (FCW-UI Not Exist).

016-311 ERROR — RAP The scanner was not detected.

016-315 ERROR — RAP NIIT Interface Fail.

016-316 ERROR — RAP Page Memory Not Detected.

016-317 ERROR — RAP Page Memory Broken-Standard.

016-318 ERROR — RAP Page Memory Broken-Option.

016-320 ERROR — RAP A fatal error with doc conversion software was detected.

016-322 ERROR — RAP JBA Account Full.

016-450 ERROR — RAP SMB Host Name Duplicated.

016-454 ERROR — RAP DNS Renewal Failure of Dynamic.

016-455 ERROR — RAP SNTP Server Time Out.

016-456 ERROR — RAP SNTP Time Asynchronous.

016-503 ERROR — RAP SMTP Server Address Resolution Fail.

016-504 ERROR — RAP POP Server Address Resolution Fail.

016-505 ERROR — RAP POP Authentication Fail.

016-600 ERROR — RAP KO Authentication Locked.

016-601 ERROR — RAP Illegal Access Detection.

016-647 ERROR — RAP With APS selected or with APS set up, there were no trays loaded with paper sizes for Auto Paper Selection.

016-648 ERROR — RAP Job with Booklet selected was discontinued because it had a cover with an image, a divider, or a blank page.

016-701 ERROR — RAP Out of ART EX Memory.

016-702 ERROR — RAP Out of Page Buffer.

016-703 ERROR — RAP Email to Invalid Box.

016-704 ERROR — RAP Mailbox is Full.

016-705 ERROR — RAP Secure Print Fail.

016-706 ERROR — RAP Max. User Number Exceeded.

016-707 ERROR — RAP Sample Print Fail.

016-708 ERROR — RAP HD Full by Annotation/Watermark Image.

016-709 ERROR — RAP ART EX Command Error.

016-710 ERROR — RAP Delayed Print Fail.

016-711 ERROR — RAP Tried to send data whose size is over the system data upper limit.

016-712 ERROR — RAP Under PANTHER Capacity (I-Formatter).

016-713 ERROR — RAP Security Box Password Error.

016-714 ERROR — RAP Security Box is not Enabled.

016-716 ERROR — RAP TIFF Data Overflow.

016-718 ERROR — RAP Out of PCL6 Memory.

016-719 ERROR — RAP Out of PCL Memory.

016-720 ERROR — RAP PCL Command Error.

016-721 ERROR — RAP Other Error.

016-722 ERROR — RAP Job Cancel by Staple Position NG.

016-723 ERROR — RAP Job Cancel by Punch Position NG.

016-724 ERROR — RAP Complex Position Error of Staple and Punch.

016-726 ERROR — RAP PDL Auto Switch Fail.

016-728 ERROR — RAP Unsupported TIFF Data.

016-729 ERROR — RAP TIFF Data Size too Big.

016-730 ERROR — RAP Unsupported ART Command.

016-731 ERROR — RAP Invalid TIFF Data.

016-732 ERROR — RAP Form Not Registered.

016-733 ERROR — RAP Destination Address Resolution Error.

016-734 ERROR — RAP Simple Transmission report invocation error.

016-735 ERROR — RAP Updating Job Template.

016-736 ERROR — RAP Remote directory lock error. Lock directory creation failed.

016-737 ERROR — RAP Remote lock directory remove error.

016-738 ERROR — RAP PS Booklet Print Output Paper Size is illegal.

016-739 ERROR — RAP Mismatch between PS Booklet Doc and Output Paper.

016-740 ERROR — RAP PS Booklet Output Tray is incorrect.

016-746 ERROR — RAP Unsupported PDF File.

016-748 ERROR — RAP HD Full.

016-749 ERROR — RAP JCL Syntax Error.

016-751 ERROR — RAP PDF Error.

016-752 ERROR — RAP PDF Short of Memory.

016-753 ERROR — RAP PDF Password Mismatched.

016-754 ERROR — RAP PDF LZW Not Installed.

016-755 ERROR — RAP PDF Print Prohibited.

016-756 ERROR — RAP Auditron-Prohibit Service.

016-757 ERROR — RAP Auditron-Invalid User.

016-758 ERROR — RAP Auditron-Disabled Function.

016-759 ERROR — RAP Auditron-Reached Limit.

016-760 ERROR — RAP PS Decompose Failure.

016-761 ERROR — RAP FIFO Empty.

016-762 ERROR — RAP Print LANG Not Installed.

016-764 ERROR — RAP SMTP Server Connect Error.

016-765 ERROR — RAP SMTP Server HD Full.

016-766 ERROR — RAP SMTP Server File System Error.

016-767 ERROR — RAP Invalid E-mail Address.

016-768 ERROR — RAP Invalid Sender Address.

016-769 ERROR — RAP SMTP Server Unsupported DSN.

016-771 ERROR — RAP Scan Data Repository ERR.

016-772 ERROR — RAP Scan Data Repository ERR.

016-773 ERROR — RAP Invalid IP Address.

016-774 ERROR — RAP HD Full-Compression Convert.

016-775 ERROR — RAP HD Full-Image Convert.

016-776 ERROR — RAP Image Convert ERR.

016-777 ERROR — RAP HD Access ERR-Image Convert.

016-778 ERROR — RAP HD Full-Scan Image Convert.

016-779 ERROR — RAP Scan Image Conversion Error.

016-780 ERROR — RAP HD Access ERR-Image Convert.

016-781 ERROR — RAP Scan Server Connect ERR.

016-782 ERROR — RAP Scan Server Login ERR.

016-783 ERROR — RAP Invalid Server Path.

016-784 ERROR — RAP Server Write ERR.

016-785 ERROR — RAP Server HD Full.

016-786 ERROR — RAP HD Full-Scan Write ERR.

016-787 ERROR — RAP Invalid Server IP ADD.

016-788 ERROR — RAP Retrieve to Browser Failed.

016-789 ERROR — RAP HD Full-Job Memory.

016-791 ERROR — RAP File Retrieve Fail.

016-792 ERROR — RAP Specified Job Not Found.

016-793 ERROR — RAP MF I/O HD Full.

016-794 ERROR — RAP Media Reader: Media No Insert.

016-795 ERROR — RAP Media Reader: Format Error.

016-796 ERROR — RAP Document insert operation error.

016-797 ERROR — RAP Media Reader: Image File Read Error.

016-798 ERROR — RAP No Trust Marking Option.

016-799 ERROR — RAP Print Instruction Fail.

016-940 ERROR — RAP With Duplex Output selected, a size difference between side 1 and side 2 was detected.

016-941 ERROR — RAP With Booklet selected, mixed-in-size/orientation pages with images were detected.

016-942 ERROR — RAP After a duplexed page was deleted, a size difference between side 1 and side 2 was detected.

016-943 ERROR — RAP After a document or divider was inserted, a size difference between side 1 and side 2 was detected.

016-944 ERROR — RAP Documents were merged, including the cover with an image, or a document with a divider.

016-945 ERROR — RAP A document unavailable for duplex print was inserted after a document available for Duplex was inserted.

016-946 ERROR — RAP A document or a divider was inserted after the cover or divider page.

016-949 ERROR — RAP The user inserted a documnet different in size/orientation from the page to be processed.

016-981 ERROR — RAP A failure in access to HDD.

016-982 ERROR — RAP HDD Access Error 2.

016-985 ERROR — RAP Data Size Over Flow (Scan to Email).

024-340 ERROR — RAP IOT-ESS Communication Failure 1.

024-341 ERROR — RAP IOT-ESS Communication Failure 2.

024-342 ERROR — RAP IOT-ESS Communication Failure 3.

024-343 ERROR — RAP IOT-ESS Communication Failure 4.

024-345 ERROR — RAP IOT-ESS Communication Failure 5.

024-346 ERROR — RAP IOT-ESS Communication Failure 6.

024-347 ERROR — RAP IOT-ESS Communication Failure 7.

024-348 ERROR — RAP IOT-ESS Communication Failure 8.

024-349 ERROR — RAP IOT-ESS Communication Failure 9.

024-350 ERROR — RAP IOT-ESS Communication Failure 10.

024-351 ERROR — RAP IOT-ESS Communication Failure 11.

024-352 ERROR — RAP IOT-ESS Communication Failure 12.

024-353 ERROR — RAP IOT-ESS Communication Failure 13.

024-354 ERROR — RAP IOT-ESS Communication Failure 14.

024-355 ERROR — RAP IOT-ESS Communication Failure 15.

024-356 ERROR — RAP IOT-ESS Communication Failure 16.

024-357 ERROR — RAP IOT-ESS Communication Failure 17.

024-358 ERROR — RAP IOT-ESS Communication Failure 18.

024-359 ERROR — RAP IOT-ESS Communication Failure 19.

024-360 ERROR — RAP IOT-ESS Initialization Failure.

024-361 ERROR — RAP Invalid IOT PaperSizeGroup Information.

024-362 ERROR — RAP Page Sync Illegal Start.

024-363 ERROR — RAP Page Sync Illegal Stop.

024-364 ERROR — RAP DMA Transfer Failure.

024-365 ERROR — RAP Overflow on the Loop Back Write.

024-366 ERROR — RAP JBIG Library Other Failure.

024-367 ERROR — RAP Decompress Other Failure.

024-368 ERROR — RAP PCI Error.

024-370 ERROR — RAP Marker Code Detect Failure.

024-371 ERROR — RAP IOT-ESS Communication Failure 21.

024-372 ERROR — RAP IOT-ESS Communication Failure 22.

024-373 ERROR — RAP IOT-ESS Communication Failure 23.

024-374 ERROR — RAP Regi Con PLL Parameter Failure.

024-375 ERROR — RAP IOT-ESS Communication Failure 24.

024-600 ERROR — RAP Billing master counter repair.

024-601 ERROR — RAP Billing backup counter #1 repair.

024-602 ERROR — RAP Billing backup counter #2 repair.

024-603 ERROR — RAP SWKey master counter repair.

024-604 ERROR — RAP SWKey backup counter #1 repair.

024-605 ERROR — RAP SWKey backup counter #2 repair.

024-606 ERROR — RAP Production Number/Serial Number Failure.

024-746 ERROR — RAP Selected Paper Tray Parameter Mismatch.

024-747 ERROR — RAP Print Instruction Failure.

024-910 ERROR — RAP Tray 1 Size Mismatch.

024-911 ERROR — RAP Tray 2 Size Mismatch.

024-912 ERROR — RAP Tray 3 Size Mismatch.

024-913 ERROR — RAP Tray 4 Size Mismatch.

024-914 ERROR — RAP Tray 6 Size Mismatch.

024-915 ERROR — RAP Tray 7 Size Mismatch.

024-917 ERROR — RAP Stacker Tray Staple Set Over Count.

024-919 ERROR — RAP Face UP Tray Close.

024-920 ERROR — RAP Face Down Tray 1 Paper FULL.

024-922 ERROR — RAP Face Down Tray 2 Paper FULL.

024-923 ERROR — RAP Operation Yellow Toner Empty.

024-924 ERROR — RAP Operation Magenta Toner Empty.

024-925 ERROR — RAP Operation Cyan Toner Empty.

024-926 ERROR — RAP Punch Dust Box Missing Set.

024-927 ERROR — RAP Offset Catch Tray Full Stack.

024-930 ERROR — RAP Stacker Tray Full (Small Size Full).

024-934 ERROR — RAP Paper type mismatch.

024-935 ERROR — RAP Tray 1 Paper Mismatch.

024-936 ERROR — RAP Tray 2 Paper Mismatch.

024-937 ERROR — RAP Tray 3 Paper Mismatch.

024-938 ERROR — RAP OHP kind Mismatch at Tray 4 (Not White Frame OHP).

024-939 ERROR — RAP Transparency type mismatch (No white border).

024-940 ERROR — RAP Folder Tray Out of Place.

024-941 ERROR — RAP Folder Tray Full Stack.

024-942 ERROR — RAP Booklet Sheets Over Count.

024-943 ERROR — RAP Booklet Low Staple.

024-945 ERROR — RAP Booklet Full Stack.

024-946 ERROR — RAP Tray 1 Not In Position.

024-947 ERROR — RAP Tray 2 Not In Position.

024-948 ERROR — RAP Tray 3 Not In Position.

024-949 ERROR — RAP Tray 4 Not In Position.

024-950 ERROR — RAP Tray 1 No Paper.

024-951 ERROR — RAP Tray 2 No Paper.

024-952 ERROR — RAP Tray 3 No Paper.

024-953 ERROR — RAP Tray 4 No Paper.

024-954 ERROR — RAP MSI No Paper.

024-955 ERROR — RAP Tray 6 No Paper.

024-956 ERROR — RAP Tray 7 No Paper.

024-957 ERROR — RAP Interposer No Paper.

024-958 ERROR — RAP MSI Size Mismatch.

024-959 ERROR — RAP Tray 1 Paper Size Mismatch.

024-960 ERROR — RAP Tray 2 Paper Size Mismatch.

024-961 ERROR — RAP Tray 3 Paper Size Mismatch.

024-962 ERROR — RAP Tray 4 Paper Size Mismatch.

024-965 ERROR — RAP ATS/APS No Paper.

024-966 ERROR — RAP ATS/APS No Destination Error.

024-967 ERROR — RAP Different Width Mix Paper Detect (Staple Job).

024-968 ERROR — RAP Stapler/Punch Batting.

024-969 ERROR — RAP Different Width Mix Punch.

024-970 ERROR — RAP Tray 6 Not In Position.

024-971 ERROR — RAP Tray 7 Not In Position.

024-972 ERROR — RAP Tray 6 Paper Size Mismatch.

024-973 ERROR — RAP Tray 7 Paper Size Mismatch.

024-974 ERROR — RAP Interposer Tray Size Mismatch.

          Во время работы с аппаратом могут возникать проблемы, связанные с неисправностями «железа» или ПО. И если расходные материалы можно просто заменить, то с «мозгами» нужно разбираться. Поэтому, для экономии времени и удобства, ниже представлены возможные коды ошибок (FAULT ERROR CODE), которые показывают Xerox DocuColor DC 240/250/242/252/260 и WorkCentre WC 7655/7665/7675/7755/7765/7775 при неисправности, и их значение:

002-770 ERROR — RAP Insufficient HDD capacity while processing the job template within a job.

003-318 ERROR — RAP IIT software failure.

003-319 ERROR — RAP IIT Video Driver Detection Fail.

003-320 ERROR — RAP IIT-ESS Communication Fail 1.

003-321 ERROR — RAP IIT-ESS Communication Fail 2.

003-322 ERROR — RAP IIT-ESS Communication Fail 3.

003-323 ERROR — RAP IIT-ESS Communication Fail 4.

003-324 ERROR — RAP IIT-ESS Communication Fail 5.

003-325 ERROR — RAP IIT-ESS Communication Fail 6.

003-326 ERROR — RAP IIT-ESS Communication Fail 7.

003-327 ERROR — RAP IIT-ESS Communication Fail 8.

003-328 ERROR — RAP IIT-ESS Communication Fail 9.

003-329 ERROR — RAP IIT-ESS Communication Fail 10.

003-330 ERROR — RAP IIT-ESS Communication Fail 11.

003-331 ERROR — RAP IIT-ESS Communication Fail 12.

003-332 ERROR — RAP IIT-ESS Communication Fail 13.

003-333 ERROR — RAP IIT-ESS Communication Fail 14.

003-334 ERROR — RAP IIT-ESS Communication Fail 15.

003-335 ERROR — RAP IIT-ESS Communication Fail 16.

003-336 ERROR — RAP IIT-ESS Communication Fail 17.

003-337 ERROR — RAP IIT-ESS Communication Fail 18.

003-338 ERROR — RAP IIT-ESS Communication Fail 19.

003-339 ERROR — RAP IIT-ESS Communication Fail 20.

003-340 ERROR — RAP IIT-ESS Communication Fail 21.

003-341 ERROR — RAP IIT-ESS Communication Fail 22.

003-342 ERROR — RAP IIT-ESS Communication Fail 23.

003-343 ERROR — RAP IIT-ESS Communication Fail 24.

003-344 ERROR — RAP Power on hotline failure.

003-345 ERROR — RAP X PIO Unmatch Fail 1.

003-346 ERROR — RAP X PIO Unmatch Fail 2.

003-750 ERROR — RAP Book Duplex-Insufficient Docs.

003-751 ERROR — RAP Under PANTHER Capacity (Scan).

003-752 ERROR — RAP This status code is displayed if 600dpi cannot be scanned (DADF).

003-753 ERROR — RAP This status code is displayed if over 300dpi cannot be scanned (DADF).

003-754 ERROR — RAP S2X Recoverable Error.

003-755 ERROR — RAP S2X Command Error.

003-757 ERROR — RAP This status code is displayed if over 400dpi cannot be scanned (DADF).

003-760 ERROR — RAP Scan Settings Error.

003-761 ERROR — RAP Incorrect Paper Tray Size.

003-763 ERROR — RAP Adjustment Chart Not Found.

003-764 ERROR — RAP Adjustment Chart Not Found.

003-780 ERROR — RAP Scan Image Compression Error.

003-795 ERROR — RAP AMS Limit Error.

003-940 ERROR — RAP DAM Memory is insufficient.

003-942 ERROR — RAP Document Size Error.

003-944 ERROR — RAP Image Repeat Count Fail.

003-946 ERROR — RAP Copy Vertical/Horizontal Difference (APS).

003-947 ERROR — RAP Replaced Original Count Error.

003-948 ERROR — RAP Replaced Original Mismatch.

003-952 ERROR — RAP Return Documents Color mismatch.

003-955 ERROR — RAP Documents Size Exchange Error.

003-956 ERROR — RAP Documents Size Unknown Error.

003-963 ERROR — RAP No APS Object Tray.

003-965 ERROR — RAP ATS/APS No Paper. There is no paper in the trays that can be selected with APS.

003-966 ERROR — RAP AATS/APS No Destination Error.

003-968 ERROR — RAP Punch Position Error.

003-969 ERROR — RAP Punch Size Error.

003-972 ERROR — RAP Maximum Stored Page Over Flow.

003-973 ERROR — RAP Every Direction Difference.

003-974 ERROR — RAP Next Original Specification.

003-977 ERROR — RAP Document Miss Match (Multi Scan).

003-978 ERROR — RAP Color Document Mismatch (Multi Scan).

003-980 ERROR — RAP Staple Position Error.

003-981 ERROR — RAP Staple Size Error.

003-982 ERROR — RAP IITsc HDD Access Error.

005-121 ERROR — RAP DADF Feed Sensor ON Jam.

005-122 ERROR — RAP DADF Simplex/Side 1 Pre Reg Sensor ON Jam.

005-123 ERROR — RAP DADF Simplex/Side 1 Reg Sensor ON Jam.

005-124 ERROR — RAP DADF Lead Reg Sensor ON Jam.

005-125 ERROR — RAP DADF Reg Sensor OFF Jam.

005-126 ERROR — RAP DADF Out Sensor ON Jam.

005-127 ERROR — RAP DADF Out Sensor OFF Jam.

005-128 ERROR — RAP DADF Exit Sensor 1 ON Jam (Simplex Mode).

005-129 ERROR — RAP DADF Exit Sensor 1 OFF Jam (Simplex Mode).

005-130 ERROR — RAP DADF Invert Sensor ON Jam (Duplex Mode).

005-131 ERROR — RAP DADF Invert Sensor On Jam (Inverting).

005-132 ERROR — RAP DADF Invert SNR on Jam 2.

005-133 ERROR — RAP DADF Invert Sensor OFF Jam.

005-134 ERROR — RAP DADF Invert SNR off Jam (Inv).

005-135 ERROR — RAP DADF Pre Reg Sensor ON Jam (Invert).

005-136 ERROR — ERROR — RAP DADF Reg Sensor ON Jam (Invert).

005-137 ERROR — RAP DADF Exit Sensor 2 ON Jam.

005-138 ERROR — RAP DADF Exit Sensor 1 ON Jam.

005-139 ERROR — RAP DADF Invert SNR off Jam.

005-141 ERROR — RAP DADF Feed Sensor OFF Jam.

005-142 ERROR — RAP DADF Exit Sensor 1 OFF Jam (Duplex Mode).

005-143 ERROR — RAP DADF Exit Sensor 2 OFF Jam.

005-144 ERROR — RAP DADF Too First Pre Reg Sensor ON Jam.

005-145 ERROR — RAP DADF Reg Sensor Off Jam (Invert).

005-146 ERROR — RAP DADF Pre Reg Sensor Off Jam.

005-147 ERROR — RAP DADF Pre Reg Sensor Off Jam (Invert).

005-150 ERROR — RAP DADF Feed Sensor OFF Jam (Perforated Original Mode).

005-151 ERROR — RAP DADF Pre Reg Sensor OFF Jam (Perforated Original Mode).

005-152 ERROR — RAP DADF Reg Sensor OFF Jam (Perforated Original Mode).

005-153 ERROR — RAP DADF Reg Sensor OFF Jam (Perforated Original Mode).

005-154 ERROR — RAP DADF Out Sensor OFF Jam (Perforated Original Mode).

005-155 ERROR — RAP DADF Exit Sensor 1 OFF Jam (Perforated Original Mode) (Simplex).

005-156 ERROR — RAP DADF Exit Sensor 1 OFF Jam (Perforated Original Mode) (Duplex).

005-157 ERROR — RAP DADF Invert Sensor OFF Jam (Perforated Original Mode).

005-158 ERROR — RAP DADF Exit Sensor 2 OFF Jam (Perforated Original Mode).

005-160 ERROR — RAP DADF Tray Lift Up Fail (Document Set) (Within Job).

005-190 ERROR — RAP DADF Feed Motor Logic Jam.

005-194 ERROR — RAP Size Mismatch Jam on Slow Scan Mix Size.

005-195 ERROR — RAP Size Mismatch Jam on No Mix Size.

005-196 ERROR — RAP Size Mismatch Jam on No Mix Size.

005-197 ERROR — RAP Prohibit Combine Size Jam.

005-198 ERROR — RAP Too Short Size Jam.

005-199 ERROR — RAP Too Long Size Jam.

005-275 ERROR — RAP DADF RAM Fail.

005-280 ERROR — RAP DADF EEPROM Fail.

005-282 ERROR — RAP DADF Tray Lift Up Fail (No Document).

005-283 ERROR — RAP DADF Stack Height Sensor Logic Fail.

005-284 ERROR — RAP DADF APS Sensor Logic Fail.

005-285 ERROR — RAP DADF Nudger Lift Up Fail.

005-286 ERROR — RAP DADF Feed Out Sensor Fail.

005-303 ERROR — RAP DADF Tray Interlock is open.

005-304 ERROR — RAP Platen Interlock Open.

005-305 ERROR — RAP DADF Feeder Cover Interlock Open (Run).

005-306 ERROR — RAP DADF Tray Interlock Open (Run).

005-308 ERROR — RAP The DADF L/H Cover Interlock is open.

005-309 ERROR — RAP DADF L/H Cover Interlock Open (Run).

005-906 ERROR — RAP DADF Feed Sensor Static Jam.

005-907 ERROR — RAP DADF Pre Reg Sensor Static Jam.

005-908 ERROR — RAP DADF Reg Sensor Static Jam.

005-909 ERROR — RAP DADF Lead Reg Sensor Static Jam..

005-910 ERROR — RAP DADF Out Sensor Static Jam.

005-911 ERROR — RAP DADF Exit Sensor 1 Static Jam.

005-912 ERROR — RAP DADF Exit Sensor 2 Static Jam.

005-913 ERROR — RAP DADF Invert Sensor Static Jam.

005-914 ERROR — RAP DADF No. 1/2/3 APS Sensor Static Jam.

005-915 ERROR — RAP DADF No. 1 APS Sensor Static Jam.

005-916 ERROR — RAP DADF No. 2 APS Sensor Static Jam.

005-917 ERROR — RAP DADF No. 3 APS Sensor Static Jam.

005-918 ERROR — RAP DADF Invert Sensor 2 Static Jam.

005-919 ERROR — RAP DADF Tray Lift Up Fail (Document Set).

005-940 ERROR — RAP DADF No Original Fail.

005-941 ERROR — RAP DADF Not Enough Document.

005-942 ERROR — RAP DADF Tray Stack Over Fail.

010-311 ERROR — RAP Fuser Heat Roll STS-1 Disconnection Fail. It was detected that fuser heat roll STS-1 disconnected.

010-319 ERROR — RAP Fuser NC Sensor Differential Amp Fail.

010-320 ERROR — RAP Heat Roll Over Heat Fail.

010-321 ERROR — RAP Fuser Nip Fail.

010-322 ERROR — RAP Fuser NC Center Sensor Disconnection Fail. (Fuser Temperature Sensor Fail).

010-323 ERROR — RAP Fuser Rear Sensor Disconnection Fail. (Fuser Temperature Sensor Fail).

010-324 ERROR — RAP Fuser NVM Fail.

010-326 ERROR — RAP Wait Heat Roll Fuser On Time Fail.

010-327 ERROR — RAP Standby Heat Roll Fuser On Time Fail.

010-330 ERROR — RAP Fuser Motor Fail.

010-420 ERROR — RAP Fuser Assembly Life Near End.

010-421 ERROR — RAP Fuser Assembly Life End.

012-112 ERROR — RAP Finisher Interface Entrance Sensor ON.

012-113 ERROR — RAP Booklet In Sensor ON Jam.

012-114 ERROR — RAP Booklet In Sensor OFF Jam.

012-115 ERROR — RAP Booklet Folder Roll Exit Sensor ON Jam.

012-125 ERROR — RAP Gate Sensor ON JAM: Finisher.

012-132 ERROR — RAP Finisher Transport Entrance Sensor ON Jam (Long).

012-142 ERROR — RAP Buffer Path Sensor ON Jam A.

012-151 ERROR — RAP Compile Exit Sensor OFF Jam.

012-152 ERROR — RAP Compile Exit Sensor ON Jam A.

012-161 ERROR — RAP Set Eject Jam.

012-162 ERROR — RAP Finisher Interface EXIT. Sensor ON Jam.

012-171 ERROR — RAP Top Tray Exit Sensor ON Jam A.

012-172 ERROR — RAP Top Tray Exit Sensor OFF Jam A.

012-180 ERROR — RAP Booklet Folder Roll Exit Sensor OFF Jam.

012-211 ERROR — RAP Stacker Tray Fail.

012-212 ERROR — RAP Stacker Tray Upper Limit Fail.

012-213 ERROR — RAP Stacker Tray Lower Limit Fail.

012-221 ERROR — RAP Tamper Home Sensor ON Fail.

012-223 ERROR — RAP Tamper Home Sensor OFF Fail.

012-224 ERROR — RAP Rear Tamper Home Sensor OFF Fail.

012-225 ERROR — RAP Booklet Tamper F Home Sensor ON Fail.

012-226 ERROR — RAP Booklet Tamper F Home Sensor OFF Fail.

012-227 ERROR — RAP Booklet End Guide Home Sensor OFF Fail.

012-228 ERROR — RAP Booklet End Guide Home Sensor ON Fail.

012-229 ERROR — RAP Booklet Tamper R Home Sensor ON Fail.

012-230 ERROR — RAP Booklet Tamper R Home Sensor OFF Fail.

012-243 ERROR — RAP Booklet Knife Home Sensor ON Fail.

012-246 ERROR — RAP Booklet Stapler Fail.

012-247 ERROR — RAP Side Regi Sensor OFF Fail.

012-260 ERROR — RAP Eject Clamp Up Sensor ON Fail.

012-261 ERROR — RAP Booklet Knife Folding SNR Fail.

012-263 ERROR — RAP Finisher Rear Tamper Home Sensor ON.

012-264 ERROR — RAP Booklet Drawer Broken Fail.

012-265 ERROR — RAP Booklet Knife Home Sensor OFF Fail.

012-266 ERROR — RAP Booklet Compiler No Paper Sensor Fail.

012-270 ERROR — RAP Top Offset Home Sensor ON Fail: Finisher.

012-271 ERROR — RAP Top Offset Home Sensor OFF Fail: Finisher.

012-282 ERROR — RAP Eject Clamp Up Sensor OFF Fail.

012-283 ERROR — RAP Finisher Set Clamp Home Sensor ON Fail.

012-284 ERROR — RAP Finisher Set Clamp Home Sensor OFF Fail.

012-291 ERROR — RAP Stapler Fail.

012-295 ERROR — RAP Finisher Stapler Move Sensor On Fail.

012-296 ERROR — RAP Finisher Stapler Move Sensor OFF Fail.

012-300 ERROR — RAP Finisher Eject Cover Open (Compiler Cover).

012-302 ERROR — RAP Finisher Front Door Interlock Open.

012-307 ERROR — RAP Booklet Drawer Set Fail.

012-320 ERROR — RAP Punch Home Sensor ON Fail.

012-321 ERROR — RAP Punch Home Sensor OFF Fail.

012-322 ERROR — RAP Puncher Move Home Sensor OFF Fail.

012-323 ERROR — RAP Puncher Move Home Sensor On Fail.

012-325 ERROR — RAP Side Regi Home Sensor On Fail.

012-330 ERROR — RAP Decurler Cam Home Sensor OFF Fail.

012-332 ERROR — RAP Decurler Cam Home Sensor ON Fail.

012-334 ERROR — RAP Download Mode Fail.

012-335 ERROR — RAP Booklet Sub CPU Communication Fail.

012-900 ERROR — RAP Buffer Path Sensor Static Jam.

012-901 ERROR — RAP Finisher Paper Remains at H-Transport Entrance.

012-902 ERROR — RAP Finisher Paper Remains H-Transport Exit.

012-903 ERROR — RAP Compile Exit Sensor Static Jam.

012-905 ERROR — RAP Compile Tray No Paper Sensor Static Jam.

012-907 ERROR — RAP Top Tray Exit Sensor Static Jam.

012-920 ERROR — RAP Gate Sensor static JAM (to Top Tray) A: Finisher.

012-932 ERROR — RAP Gate SNR static JAM (to Stacker Tray) A.

012-934 ERROR — RAP Gate SNR static JAM (to Stacker Tray) C.

012-935 ERROR — RAP Finisher Paper Remains at Transport Entrance Sensor.

012-936 ERROR — RAP Paper Remain at Booklet In SNR A.

012-949 ERROR — RAP Finisher Punch DustBox Miss Set.

013-902 ERROR — RAP Booklet Compile No Paper Sensor Static Jam.

013-903 ERROR — RAP Booklet Folder Roll Exit Sensor Static Jam.

016-210 ERROR — RAP Software Option Fail (HDD Not Exist).

016-211 ERROR — RAP Software Option Fail (System Memory Low Volume).

016-212 ERROR — RAP SW Option Fail (Page Memory Low).

016-213 ERROR — RAP SW Option Fail (Printer CARD Not Exist).

016-215 ERROR — RAP SW Option Fail (JPEG Board Not Exist).

016-216 ERROR — RAP SW Option Fail (Ext Memory Not Exist).

016-217 ERROR — RAP SW Option Fail (Controller ROM not Printer kit).

016-218 ERROR — RAP Because PS Kit is not installed, XDOD functions cannot be fulfilled.

016-219 ERROR — RAP License is required (Printer Kit).

016-220 ERROR — RAP S2X Unrecoverable Error.

016-221 ERROR — RAP S2X Communication Error.

016-222 ERROR — RAP S2X Self-Diag Error.

016-223 ERROR — RAP SS2X SDRAM Error.

016-224 ERROR — RAP S2X PCI Reg Error.

016-225 ERROR — RAP S2X ROM CheckSum Error.

016-226 ERROR — RAP S2X IIT Connection Error.

016-227 ERROR — RAP S2X DDR Error.

016-228 ERROR — RAP S2X Image Processing Error.

016-229 ERROR — RAP SW Option Fail (FCW-UI Not Exist).

016-311 ERROR — RAP The scanner was not detected.

016-315 ERROR — RAP NIIT Interface Fail.

016-316 ERROR — RAP Page Memory Not Detected.

016-317 ERROR — RAP Page Memory Broken-Standard.

016-318 ERROR — RAP Page Memory Broken-Option.

016-320 ERROR — RAP A fatal error with doc conversion software was detected.

016-322 ERROR — RAP JBA Account Full.

016-450 ERROR — RAP SMB Host Name Duplicated.

016-454 ERROR — RAP DNS Renewal Failure of Dynamic.

016-455 ERROR — RAP SNTP Server Time Out.

016-456 ERROR — RAP SNTP Time Asynchronous.

016-503 ERROR — RAP SMTP Server Address Resolution Fail.

016-504 ERROR — RAP POP Server Address Resolution Fail.

016-505 ERROR — RAP POP Authentication Fail.

016-600 ERROR — RAP KO Authentication Locked.

016-601 ERROR — RAP Illegal Access Detection.

016-647 ERROR — RAP With APS selected or with APS set up, there were no trays loaded with paper sizes for Auto Paper Selection.

016-648 ERROR — RAP Job with Booklet selected was discontinued because it had a cover with an image, a divider, or a blank page.

016-701 ERROR — RAP Out of ART EX Memory.

016-702 ERROR — RAP Out of Page Buffer.

016-703 ERROR — RAP Email to Invalid Box.

016-704 ERROR — RAP Mailbox is Full.

016-705 ERROR — RAP Secure Print Fail.

016-706 ERROR — RAP Max. User Number Exceeded.

016-707 ERROR — RAP Sample Print Fail.

016-708 ERROR — RAP HD Full by Annotation/Watermark Image.

016-709 ERROR — RAP ART EX Command Error.

016-710 ERROR — RAP Delayed Print Fail.

016-711 ERROR — RAP Tried to send data whose size is over the system data upper limit.

016-712 ERROR — RAP Under PANTHER Capacity (I-Formatter).

016-713 ERROR — RAP Security Box Password Error.

016-714 ERROR — RAP Security Box is not Enabled.

016-716 ERROR — RAP TIFF Data Overflow.

016-718 ERROR — RAP Out of PCL6 Memory.

016-719 ERROR — RAP Out of PCL Memory.

016-720 ERROR — RAP PCL Command Error.

016-721 ERROR — RAP Other Error.

016-722 ERROR — RAP Job Cancel by Staple Position NG.

016-723 ERROR — RAP Job Cancel by Punch Position NG.

016-724 ERROR — RAP Complex Position Error of Staple and Punch.

016-726 ERROR — RAP PDL Auto Switch Fail.

016-728 ERROR — RAP Unsupported TIFF Data.

016-729 ERROR — RAP TIFF Data Size too Big.

016-730 ERROR — RAP Unsupported ART Command.

016-731 ERROR — RAP Invalid TIFF Data.

016-732 ERROR — RAP Form Not Registered.

016-733 ERROR — RAP Destination Address Resolution Error.

016-734 ERROR — RAP Simple Transmission report invocation error.

016-735 ERROR — RAP Updating Job Template.

016-736 ERROR — RAP Remote directory lock error. Lock directory creation failed.

016-737 ERROR — RAP Remote lock directory remove error.

016-738 ERROR — RAP PS Booklet Print Output Paper Size is illegal.

016-739 ERROR — RAP Mismatch between PS Booklet Doc and Output Paper.

016-740 ERROR — RAP PS Booklet Output Tray is incorrect.

016-746 ERROR — RAP Unsupported PDF File.

016-748 ERROR — RAP HD Full.

016-749 ERROR — RAP JCL Syntax Error.

016-751 ERROR — RAP PDF Error.

016-752 ERROR — RAP PDF Short of Memory.

016-753 ERROR — RAP PDF Password Mismatched.

016-754 ERROR — RAP PDF LZW Not Installed.

016-755 ERROR — RAP PDF Print Prohibited.

016-756 ERROR — RAP Auditron-Prohibit Service.

016-757 ERROR — RAP Auditron-Invalid User.

016-758 ERROR — RAP Auditron-Disabled Function.

016-759 ERROR — RAP Auditron-Reached Limit.

016-760 ERROR — RAP PS Decompose Failure.

016-761 ERROR — RAP FIFO Empty.

016-762 ERROR — RAP Print LANG Not Installed.

016-764 ERROR — RAP SMTP Server Connect Error.

016-765 ERROR — RAP SMTP Server HD Full.

016-766 ERROR — RAP SMTP Server File System Error.

016-767 ERROR — RAP Invalid E-mail Address.

016-768 ERROR — RAP Invalid Sender Address.

016-769 ERROR — RAP SMTP Server Unsupported DSN.

016-771 ERROR — RAP Scan Data Repository ERR.

016-772 ERROR — RAP Scan Data Repository ERR.

016-773 ERROR — RAP Invalid IP Address.

016-774 ERROR — RAP HD Full-Compression Convert.

016-775 ERROR — RAP HD Full-Image Convert.

016-776 ERROR — RAP Image Convert ERR.

016-777 ERROR — RAP HD Access ERR-Image Convert.

016-778 ERROR — RAP HD Full-Scan Image Convert.

016-779 ERROR — RAP Scan Image Conversion Error.

016-780 ERROR — RAP HD Access ERR-Image Convert.

016-781 ERROR — RAP Scan Server Connect ERR.

016-782 ERROR — RAP Scan Server Login ERR.

016-783 ERROR — RAP Invalid Server Path.

016-784 ERROR — RAP Server Write ERR.

016-785 ERROR — RAP Server HD Full.

016-786 ERROR — RAP HD Full-Scan Write ERR.

016-787 ERROR — RAP Invalid Server IP ADD.

016-788 ERROR — RAP Retrieve to Browser Failed.

016-789 ERROR — RAP HD Full-Job Memory.

016-791 ERROR — RAP File Retrieve Fail.

016-792 ERROR — RAP Specified Job Not Found.

016-793 ERROR — RAP MF I/O HD Full.

016-794 ERROR — RAP Media Reader: Media No Insert.

016-795 ERROR — RAP Media Reader: Format Error.

016-796 ERROR — RAP Document insert operation error.

016-797 ERROR — RAP Media Reader: Image File Read Error.

016-798 ERROR — RAP No Trust Marking Option.

016-799 ERROR — RAP Print Instruction Fail.

016-940 ERROR — RAP With Duplex Output selected, a size difference between side 1 and side 2 was detected.

016-941 ERROR — RAP With Booklet selected, mixed-in-size/orientation pages with images were detected.

016-942 ERROR — RAP After a duplexed page was deleted, a size difference between side 1 and side 2 was detected.

016-943 ERROR — RAP After a document or divider was inserted, a size difference between side 1 and side 2 was detected.

016-944 ERROR — RAP Documents were merged, including the cover with an image, or a document with a divider.

016-945 ERROR — RAP A document unavailable for duplex print was inserted after a document available for Duplex was inserted.

016-946 ERROR — RAP A document or a divider was inserted after the cover or divider page.

016-949 ERROR — RAP The user inserted a documnet different in size/orientation from the page to be processed.

016-981 ERROR — RAP A failure in access to HDD.

016-982 ERROR — RAP HDD Access Error 2.

016-985 ERROR — RAP Data Size Over Flow (Scan to Email).

024-340 ERROR — RAP IOT-ESS Communication Failure 1.

024-341 ERROR — RAP IOT-ESS Communication Failure 2.

024-342 ERROR — RAP IOT-ESS Communication Failure 3.

024-343 ERROR — RAP IOT-ESS Communication Failure 4.

024-345 ERROR — RAP IOT-ESS Communication Failure 5.

024-346 ERROR — RAP IOT-ESS Communication Failure 6.

024-347 ERROR — RAP IOT-ESS Communication Failure 7.

024-348 ERROR — RAP IOT-ESS Communication Failure 8.

024-349 ERROR — RAP IOT-ESS Communication Failure 9.

024-350 ERROR — RAP IOT-ESS Communication Failure 10.

024-351 ERROR — RAP IOT-ESS Communication Failure 11.

024-352 ERROR — RAP IOT-ESS Communication Failure 12.

024-353 ERROR — RAP IOT-ESS Communication Failure 13.

024-354 ERROR — RAP IOT-ESS Communication Failure 14.

024-355 ERROR — RAP IOT-ESS Communication Failure 15.

024-356 ERROR — RAP IOT-ESS Communication Failure 16.

024-357 ERROR — RAP IOT-ESS Communication Failure 17.

024-358 ERROR — RAP IOT-ESS Communication Failure 18.

024-359 ERROR — RAP IOT-ESS Communication Failure 19.

024-360 ERROR — RAP IOT-ESS Initialization Failure.

024-361 ERROR — RAP Invalid IOT PaperSizeGroup Information.

024-362 ERROR — RAP Page Sync Illegal Start.

024-363 ERROR — RAP Page Sync Illegal Stop.

024-364 ERROR — RAP DMA Transfer Failure.

024-365 ERROR — RAP Overflow on the Loop Back Write.

024-366 ERROR — RAP JBIG Library Other Failure.

024-367 ERROR — RAP Decompress Other Failure.

024-368 ERROR — RAP PCI Error.

024-370 ERROR — RAP Marker Code Detect Failure.

024-371 ERROR — RAP IOT-ESS Communication Failure 21.

024-372 ERROR — RAP IOT-ESS Communication Failure 22.

024-373 ERROR — RAP IOT-ESS Communication Failure 23.

024-374 ERROR — RAP Regi Con PLL Parameter Failure.

024-375 ERROR — RAP IOT-ESS Communication Failure 24.

024-600 ERROR — RAP Billing master counter repair.

024-601 ERROR — RAP Billing backup counter #1 repair.

024-602 ERROR — RAP Billing backup counter #2 repair.

024-603 ERROR — RAP SWKey master counter repair.

024-604 ERROR — RAP SWKey backup counter #1 repair.

024-605 ERROR — RAP SWKey backup counter #2 repair.

024-606 ERROR — RAP Production Number/Serial Number Failure.

024-746 ERROR — RAP Selected Paper Tray Parameter Mismatch.

024-747 ERROR — RAP Print Instruction Failure.

024-910 ERROR — RAP Tray 1 Size Mismatch.

024-911 ERROR — RAP Tray 2 Size Mismatch.

024-912 ERROR — RAP Tray 3 Size Mismatch.

024-913 ERROR — RAP Tray 4 Size Mismatch.

024-914 ERROR — RAP Tray 6 Size Mismatch.

024-915 ERROR — RAP Tray 7 Size Mismatch.

024-917 ERROR — RAP Stacker Tray Staple Set Over Count.

024-919 ERROR — RAP Face UP Tray Close.

024-920 ERROR — RAP Face Down Tray 1 Paper FULL.

024-922 ERROR — RAP Face Down Tray 2 Paper FULL.

024-923 ERROR — RAP Operation Yellow Toner Empty.

024-924 ERROR — RAP Operation Magenta Toner Empty.

024-925 ERROR — RAP Operation Cyan Toner Empty.

024-926 ERROR — RAP Punch Dust Box Missing Set.

024-927 ERROR — RAP Offset Catch Tray Full Stack.

024-930 ERROR — RAP Stacker Tray Full (Small Size Full).

024-934 ERROR — RAP Paper type mismatch.

024-935 ERROR — RAP Tray 1 Paper Mismatch.

024-936 ERROR — RAP Tray 2 Paper Mismatch.

024-937 ERROR — RAP Tray 3 Paper Mismatch.

024-938 ERROR — RAP OHP kind Mismatch at Tray 4 (Not White Frame OHP).

024-939 ERROR — RAP Transparency type mismatch (No white border).

024-940 ERROR — RAP Folder Tray Out of Place.

024-941 ERROR — RAP Folder Tray Full Stack.

024-942 ERROR — RAP Booklet Sheets Over Count.

024-943 ERROR — RAP Booklet Low Staple.

024-945 ERROR — RAP Booklet Full Stack.

024-946 ERROR — RAP Tray 1 Not In Position.

024-947 ERROR — RAP Tray 2 Not In Position.

024-948 ERROR — RAP Tray 3 Not In Position.

024-949 ERROR — RAP Tray 4 Not In Position.

024-950 ERROR — RAP Tray 1 No Paper.

024-951 ERROR — RAP Tray 2 No Paper.

024-952 ERROR — RAP Tray 3 No Paper.

024-953 ERROR — RAP Tray 4 No Paper.

024-954 ERROR — RAP MSI No Paper.

024-955 ERROR — RAP Tray 6 No Paper.

024-956 ERROR — RAP Tray 7 No Paper.

024-957 ERROR — RAP Interposer No Paper.

024-958 ERROR — RAP MSI Size Mismatch.

024-959 ERROR — RAP Tray 1 Paper Size Mismatch.

024-960 ERROR — RAP Tray 2 Paper Size Mismatch.

024-961 ERROR — RAP Tray 3 Paper Size Mismatch.

024-962 ERROR — RAP Tray 4 Paper Size Mismatch.

024-965 ERROR — RAP ATS/APS No Paper.

024-966 ERROR — RAP ATS/APS No Destination Error.

024-967 ERROR — RAP Different Width Mix Paper Detect (Staple Job).

024-968 ERROR — RAP Stapler/Punch Batting.

024-969 ERROR — RAP Different Width Mix Punch.

024-970 ERROR — RAP Tray 6 Not In Position.

024-971 ERROR — RAP Tray 7 Not In Position.

024-972 ERROR — RAP Tray 6 Paper Size Mismatch.

024-973 ERROR — RAP Tray 7 Paper Size Mismatch.

024-974 ERROR — RAP Interposer Tray Size Mismatch.

          Во время работы с аппаратом могут возникать проблемы, связанные с неисправностями «железа» или ПО. И если расходные материалы можно просто заменить, то с «мозгами» нужно разбираться. Поэтому, для экономии времени и удобства, ниже представлены возможные коды ошибок (FAULT ERROR CODE), которые показывают Xerox DocuColor DC 240/250/242/252/260 и WorkCentre WC 7655/7665/7675/7755/7765/7775 при неисправности, и их значение:

002-770 ERROR — RAP Insufficient HDD capacity while processing the job template within a job.

003-318 ERROR — RAP IIT software failure.

003-319 ERROR — RAP IIT Video Driver Detection Fail.

003-320 ERROR — RAP IIT-ESS Communication Fail 1.

003-321 ERROR — RAP IIT-ESS Communication Fail 2.

003-322 ERROR — RAP IIT-ESS Communication Fail 3.

003-323 ERROR — RAP IIT-ESS Communication Fail 4.

003-324 ERROR — RAP IIT-ESS Communication Fail 5.

003-325 ERROR — RAP IIT-ESS Communication Fail 6.

003-326 ERROR — RAP IIT-ESS Communication Fail 7.

003-327 ERROR — RAP IIT-ESS Communication Fail 8.

003-328 ERROR — RAP IIT-ESS Communication Fail 9.

003-329 ERROR — RAP IIT-ESS Communication Fail 10.

003-330 ERROR — RAP IIT-ESS Communication Fail 11.

003-331 ERROR — RAP IIT-ESS Communication Fail 12.

003-332 ERROR — RAP IIT-ESS Communication Fail 13.

003-333 ERROR — RAP IIT-ESS Communication Fail 14.

003-334 ERROR — RAP IIT-ESS Communication Fail 15.

003-335 ERROR — RAP IIT-ESS Communication Fail 16.

003-336 ERROR — RAP IIT-ESS Communication Fail 17.

003-337 ERROR — RAP IIT-ESS Communication Fail 18.

003-338 ERROR — RAP IIT-ESS Communication Fail 19.

003-339 ERROR — RAP IIT-ESS Communication Fail 20.

003-340 ERROR — RAP IIT-ESS Communication Fail 21.

003-341 ERROR — RAP IIT-ESS Communication Fail 22.

003-342 ERROR — RAP IIT-ESS Communication Fail 23.

003-343 ERROR — RAP IIT-ESS Communication Fail 24.

003-344 ERROR — RAP Power on hotline failure.

003-345 ERROR — RAP X PIO Unmatch Fail 1.

003-346 ERROR — RAP X PIO Unmatch Fail 2.

003-750 ERROR — RAP Book Duplex-Insufficient Docs.

003-751 ERROR — RAP Under PANTHER Capacity (Scan).

003-752 ERROR — RAP This status code is displayed if 600dpi cannot be scanned (DADF).

003-753 ERROR — RAP This status code is displayed if over 300dpi cannot be scanned (DADF).

003-754 ERROR — RAP S2X Recoverable Error.

003-755 ERROR — RAP S2X Command Error.

003-757 ERROR — RAP This status code is displayed if over 400dpi cannot be scanned (DADF).

003-760 ERROR — RAP Scan Settings Error.

003-761 ERROR — RAP Incorrect Paper Tray Size.

003-763 ERROR — RAP Adjustment Chart Not Found.

003-764 ERROR — RAP Adjustment Chart Not Found.

003-780 ERROR — RAP Scan Image Compression Error.

003-795 ERROR — RAP AMS Limit Error.

003-940 ERROR — RAP DAM Memory is insufficient.

003-942 ERROR — RAP Document Size Error.

003-944 ERROR — RAP Image Repeat Count Fail.

003-946 ERROR — RAP Copy Vertical/Horizontal Difference (APS).

003-947 ERROR — RAP Replaced Original Count Error.

003-948 ERROR — RAP Replaced Original Mismatch.

003-952 ERROR — RAP Return Documents Color mismatch.

003-955 ERROR — RAP Documents Size Exchange Error.

003-956 ERROR — RAP Documents Size Unknown Error.

003-963 ERROR — RAP No APS Object Tray.

003-965 ERROR — RAP ATS/APS No Paper. There is no paper in the trays that can be selected with APS.

003-966 ERROR — RAP AATS/APS No Destination Error.

003-968 ERROR — RAP Punch Position Error.

003-969 ERROR — RAP Punch Size Error.

003-972 ERROR — RAP Maximum Stored Page Over Flow.

003-973 ERROR — RAP Every Direction Difference.

003-974 ERROR — RAP Next Original Specification.

003-977 ERROR — RAP Document Miss Match (Multi Scan).

003-978 ERROR — RAP Color Document Mismatch (Multi Scan).

003-980 ERROR — RAP Staple Position Error.

003-981 ERROR — RAP Staple Size Error.

003-982 ERROR — RAP IITsc HDD Access Error.

005-121 ERROR — RAP DADF Feed Sensor ON Jam.

005-122 ERROR — RAP DADF Simplex/Side 1 Pre Reg Sensor ON Jam.

005-123 ERROR — RAP DADF Simplex/Side 1 Reg Sensor ON Jam.

005-124 ERROR — RAP DADF Lead Reg Sensor ON Jam.

005-125 ERROR — RAP DADF Reg Sensor OFF Jam.

005-126 ERROR — RAP DADF Out Sensor ON Jam.

005-127 ERROR — RAP DADF Out Sensor OFF Jam.

005-128 ERROR — RAP DADF Exit Sensor 1 ON Jam (Simplex Mode).

005-129 ERROR — RAP DADF Exit Sensor 1 OFF Jam (Simplex Mode).

005-130 ERROR — RAP DADF Invert Sensor ON Jam (Duplex Mode).

005-131 ERROR — RAP DADF Invert Sensor On Jam (Inverting).

005-132 ERROR — RAP DADF Invert SNR on Jam 2.

005-133 ERROR — RAP DADF Invert Sensor OFF Jam.

005-134 ERROR — RAP DADF Invert SNR off Jam (Inv).

005-135 ERROR — RAP DADF Pre Reg Sensor ON Jam (Invert).

005-136 ERROR — ERROR — RAP DADF Reg Sensor ON Jam (Invert).

005-137 ERROR — RAP DADF Exit Sensor 2 ON Jam.

005-138 ERROR — RAP DADF Exit Sensor 1 ON Jam.

005-139 ERROR — RAP DADF Invert SNR off Jam.

005-141 ERROR — RAP DADF Feed Sensor OFF Jam.

005-142 ERROR — RAP DADF Exit Sensor 1 OFF Jam (Duplex Mode).

005-143 ERROR — RAP DADF Exit Sensor 2 OFF Jam.

005-144 ERROR — RAP DADF Too First Pre Reg Sensor ON Jam.

005-145 ERROR — RAP DADF Reg Sensor Off Jam (Invert).

005-146 ERROR — RAP DADF Pre Reg Sensor Off Jam.

005-147 ERROR — RAP DADF Pre Reg Sensor Off Jam (Invert).

005-150 ERROR — RAP DADF Feed Sensor OFF Jam (Perforated Original Mode).

005-151 ERROR — RAP DADF Pre Reg Sensor OFF Jam (Perforated Original Mode).

005-152 ERROR — RAP DADF Reg Sensor OFF Jam (Perforated Original Mode).

005-153 ERROR — RAP DADF Reg Sensor OFF Jam (Perforated Original Mode).

005-154 ERROR — RAP DADF Out Sensor OFF Jam (Perforated Original Mode).

005-155 ERROR — RAP DADF Exit Sensor 1 OFF Jam (Perforated Original Mode) (Simplex).

005-156 ERROR — RAP DADF Exit Sensor 1 OFF Jam (Perforated Original Mode) (Duplex).

005-157 ERROR — RAP DADF Invert Sensor OFF Jam (Perforated Original Mode).

005-158 ERROR — RAP DADF Exit Sensor 2 OFF Jam (Perforated Original Mode).

005-160 ERROR — RAP DADF Tray Lift Up Fail (Document Set) (Within Job).

005-190 ERROR — RAP DADF Feed Motor Logic Jam.

005-194 ERROR — RAP Size Mismatch Jam on Slow Scan Mix Size.

005-195 ERROR — RAP Size Mismatch Jam on No Mix Size.

005-196 ERROR — RAP Size Mismatch Jam on No Mix Size.

005-197 ERROR — RAP Prohibit Combine Size Jam.

005-198 ERROR — RAP Too Short Size Jam.

005-199 ERROR — RAP Too Long Size Jam.

005-275 ERROR — RAP DADF RAM Fail.

005-280 ERROR — RAP DADF EEPROM Fail.

005-282 ERROR — RAP DADF Tray Lift Up Fail (No Document).

005-283 ERROR — RAP DADF Stack Height Sensor Logic Fail.

005-284 ERROR — RAP DADF APS Sensor Logic Fail.

005-285 ERROR — RAP DADF Nudger Lift Up Fail.

005-286 ERROR — RAP DADF Feed Out Sensor Fail.

005-303 ERROR — RAP DADF Tray Interlock is open.

005-304 ERROR — RAP Platen Interlock Open.

005-305 ERROR — RAP DADF Feeder Cover Interlock Open (Run).

005-306 ERROR — RAP DADF Tray Interlock Open (Run).

005-308 ERROR — RAP The DADF L/H Cover Interlock is open.

005-309 ERROR — RAP DADF L/H Cover Interlock Open (Run).

005-906 ERROR — RAP DADF Feed Sensor Static Jam.

005-907 ERROR — RAP DADF Pre Reg Sensor Static Jam.

005-908 ERROR — RAP DADF Reg Sensor Static Jam.

005-909 ERROR — RAP DADF Lead Reg Sensor Static Jam..

005-910 ERROR — RAP DADF Out Sensor Static Jam.

005-911 ERROR — RAP DADF Exit Sensor 1 Static Jam.

005-912 ERROR — RAP DADF Exit Sensor 2 Static Jam.

005-913 ERROR — RAP DADF Invert Sensor Static Jam.

005-914 ERROR — RAP DADF No. 1/2/3 APS Sensor Static Jam.

005-915 ERROR — RAP DADF No. 1 APS Sensor Static Jam.

005-916 ERROR — RAP DADF No. 2 APS Sensor Static Jam.

005-917 ERROR — RAP DADF No. 3 APS Sensor Static Jam.

005-918 ERROR — RAP DADF Invert Sensor 2 Static Jam.

005-919 ERROR — RAP DADF Tray Lift Up Fail (Document Set).

005-940 ERROR — RAP DADF No Original Fail.

005-941 ERROR — RAP DADF Not Enough Document.

005-942 ERROR — RAP DADF Tray Stack Over Fail.

010-311 ERROR — RAP Fuser Heat Roll STS-1 Disconnection Fail. It was detected that fuser heat roll STS-1 disconnected.

010-319 ERROR — RAP Fuser NC Sensor Differential Amp Fail.

010-320 ERROR — RAP Heat Roll Over Heat Fail.

010-321 ERROR — RAP Fuser Nip Fail.

010-322 ERROR — RAP Fuser NC Center Sensor Disconnection Fail. (Fuser Temperature Sensor Fail).

010-323 ERROR — RAP Fuser Rear Sensor Disconnection Fail. (Fuser Temperature Sensor Fail).

010-324 ERROR — RAP Fuser NVM Fail.

010-326 ERROR — RAP Wait Heat Roll Fuser On Time Fail.

010-327 ERROR — RAP Standby Heat Roll Fuser On Time Fail.

010-330 ERROR — RAP Fuser Motor Fail.

010-420 ERROR — RAP Fuser Assembly Life Near End.

010-421 ERROR — RAP Fuser Assembly Life End.

012-112 ERROR — RAP Finisher Interface Entrance Sensor ON.

012-113 ERROR — RAP Booklet In Sensor ON Jam.

012-114 ERROR — RAP Booklet In Sensor OFF Jam.

012-115 ERROR — RAP Booklet Folder Roll Exit Sensor ON Jam.

012-125 ERROR — RAP Gate Sensor ON JAM: Finisher.

012-132 ERROR — RAP Finisher Transport Entrance Sensor ON Jam (Long).

012-142 ERROR — RAP Buffer Path Sensor ON Jam A.

012-151 ERROR — RAP Compile Exit Sensor OFF Jam.

012-152 ERROR — RAP Compile Exit Sensor ON Jam A.

012-161 ERROR — RAP Set Eject Jam.

012-162 ERROR — RAP Finisher Interface EXIT. Sensor ON Jam.

012-171 ERROR — RAP Top Tray Exit Sensor ON Jam A.

012-172 ERROR — RAP Top Tray Exit Sensor OFF Jam A.

012-180 ERROR — RAP Booklet Folder Roll Exit Sensor OFF Jam.

012-211 ERROR — RAP Stacker Tray Fail.

012-212 ERROR — RAP Stacker Tray Upper Limit Fail.

012-213 ERROR — RAP Stacker Tray Lower Limit Fail.

012-221 ERROR — RAP Tamper Home Sensor ON Fail.

012-223 ERROR — RAP Tamper Home Sensor OFF Fail.

012-224 ERROR — RAP Rear Tamper Home Sensor OFF Fail.

012-225 ERROR — RAP Booklet Tamper F Home Sensor ON Fail.

012-226 ERROR — RAP Booklet Tamper F Home Sensor OFF Fail.

012-227 ERROR — RAP Booklet End Guide Home Sensor OFF Fail.

012-228 ERROR — RAP Booklet End Guide Home Sensor ON Fail.

012-229 ERROR — RAP Booklet Tamper R Home Sensor ON Fail.

012-230 ERROR — RAP Booklet Tamper R Home Sensor OFF Fail.

012-243 ERROR — RAP Booklet Knife Home Sensor ON Fail.

012-246 ERROR — RAP Booklet Stapler Fail.

012-247 ERROR — RAP Side Regi Sensor OFF Fail.

012-260 ERROR — RAP Eject Clamp Up Sensor ON Fail.

012-261 ERROR — RAP Booklet Knife Folding SNR Fail.

012-263 ERROR — RAP Finisher Rear Tamper Home Sensor ON.

012-264 ERROR — RAP Booklet Drawer Broken Fail.

012-265 ERROR — RAP Booklet Knife Home Sensor OFF Fail.

012-266 ERROR — RAP Booklet Compiler No Paper Sensor Fail.

012-270 ERROR — RAP Top Offset Home Sensor ON Fail: Finisher.

012-271 ERROR — RAP Top Offset Home Sensor OFF Fail: Finisher.

012-282 ERROR — RAP Eject Clamp Up Sensor OFF Fail.

012-283 ERROR — RAP Finisher Set Clamp Home Sensor ON Fail.

012-284 ERROR — RAP Finisher Set Clamp Home Sensor OFF Fail.

012-291 ERROR — RAP Stapler Fail.

012-295 ERROR — RAP Finisher Stapler Move Sensor On Fail.

012-296 ERROR — RAP Finisher Stapler Move Sensor OFF Fail.

012-300 ERROR — RAP Finisher Eject Cover Open (Compiler Cover).

012-302 ERROR — RAP Finisher Front Door Interlock Open.

012-307 ERROR — RAP Booklet Drawer Set Fail.

012-320 ERROR — RAP Punch Home Sensor ON Fail.

012-321 ERROR — RAP Punch Home Sensor OFF Fail.

012-322 ERROR — RAP Puncher Move Home Sensor OFF Fail.

012-323 ERROR — RAP Puncher Move Home Sensor On Fail.

012-325 ERROR — RAP Side Regi Home Sensor On Fail.

012-330 ERROR — RAP Decurler Cam Home Sensor OFF Fail.

012-332 ERROR — RAP Decurler Cam Home Sensor ON Fail.

012-334 ERROR — RAP Download Mode Fail.

012-335 ERROR — RAP Booklet Sub CPU Communication Fail.

012-900 ERROR — RAP Buffer Path Sensor Static Jam.

012-901 ERROR — RAP Finisher Paper Remains at H-Transport Entrance.

012-902 ERROR — RAP Finisher Paper Remains H-Transport Exit.

012-903 ERROR — RAP Compile Exit Sensor Static Jam.

012-905 ERROR — RAP Compile Tray No Paper Sensor Static Jam.

012-907 ERROR — RAP Top Tray Exit Sensor Static Jam.

012-920 ERROR — RAP Gate Sensor static JAM (to Top Tray) A: Finisher.

012-932 ERROR — RAP Gate SNR static JAM (to Stacker Tray) A.

012-934 ERROR — RAP Gate SNR static JAM (to Stacker Tray) C.

012-935 ERROR — RAP Finisher Paper Remains at Transport Entrance Sensor.

012-936 ERROR — RAP Paper Remain at Booklet In SNR A.

012-949 ERROR — RAP Finisher Punch DustBox Miss Set.

013-902 ERROR — RAP Booklet Compile No Paper Sensor Static Jam.

013-903 ERROR — RAP Booklet Folder Roll Exit Sensor Static Jam.

016-210 ERROR — RAP Software Option Fail (HDD Not Exist).

016-211 ERROR — RAP Software Option Fail (System Memory Low Volume).

016-212 ERROR — RAP SW Option Fail (Page Memory Low).

016-213 ERROR — RAP SW Option Fail (Printer CARD Not Exist).

016-215 ERROR — RAP SW Option Fail (JPEG Board Not Exist).

016-216 ERROR — RAP SW Option Fail (Ext Memory Not Exist).

016-217 ERROR — RAP SW Option Fail (Controller ROM not Printer kit).

016-218 ERROR — RAP Because PS Kit is not installed, XDOD functions cannot be fulfilled.

016-219 ERROR — RAP License is required (Printer Kit).

016-220 ERROR — RAP S2X Unrecoverable Error.

016-221 ERROR — RAP S2X Communication Error.

016-222 ERROR — RAP S2X Self-Diag Error.

016-223 ERROR — RAP SS2X SDRAM Error.

016-224 ERROR — RAP S2X PCI Reg Error.

016-225 ERROR — RAP S2X ROM CheckSum Error.

016-226 ERROR — RAP S2X IIT Connection Error.

016-227 ERROR — RAP S2X DDR Error.

016-228 ERROR — RAP S2X Image Processing Error.

016-229 ERROR — RAP SW Option Fail (FCW-UI Not Exist).

016-311 ERROR — RAP The scanner was not detected.

016-315 ERROR — RAP NIIT Interface Fail.

016-316 ERROR — RAP Page Memory Not Detected.

016-317 ERROR — RAP Page Memory Broken-Standard.

016-318 ERROR — RAP Page Memory Broken-Option.

016-320 ERROR — RAP A fatal error with doc conversion software was detected.

016-322 ERROR — RAP JBA Account Full.

016-450 ERROR — RAP SMB Host Name Duplicated.

016-454 ERROR — RAP DNS Renewal Failure of Dynamic.

016-455 ERROR — RAP SNTP Server Time Out.

016-456 ERROR — RAP SNTP Time Asynchronous.

016-503 ERROR — RAP SMTP Server Address Resolution Fail.

016-504 ERROR — RAP POP Server Address Resolution Fail.

016-505 ERROR — RAP POP Authentication Fail.

016-600 ERROR — RAP KO Authentication Locked.

016-601 ERROR — RAP Illegal Access Detection.

016-647 ERROR — RAP With APS selected or with APS set up, there were no trays loaded with paper sizes for Auto Paper Selection.

016-648 ERROR — RAP Job with Booklet selected was discontinued because it had a cover with an image, a divider, or a blank page.

016-701 ERROR — RAP Out of ART EX Memory.

016-702 ERROR — RAP Out of Page Buffer.

016-703 ERROR — RAP Email to Invalid Box.

016-704 ERROR — RAP Mailbox is Full.

016-705 ERROR — RAP Secure Print Fail.

016-706 ERROR — RAP Max. User Number Exceeded.

016-707 ERROR — RAP Sample Print Fail.

016-708 ERROR — RAP HD Full by Annotation/Watermark Image.

016-709 ERROR — RAP ART EX Command Error.

016-710 ERROR — RAP Delayed Print Fail.

016-711 ERROR — RAP Tried to send data whose size is over the system data upper limit.

016-712 ERROR — RAP Under PANTHER Capacity (I-Formatter).

016-713 ERROR — RAP Security Box Password Error.

016-714 ERROR — RAP Security Box is not Enabled.

016-716 ERROR — RAP TIFF Data Overflow.

016-718 ERROR — RAP Out of PCL6 Memory.

016-719 ERROR — RAP Out of PCL Memory.

016-720 ERROR — RAP PCL Command Error.

016-721 ERROR — RAP Other Error.

016-722 ERROR — RAP Job Cancel by Staple Position NG.

016-723 ERROR — RAP Job Cancel by Punch Position NG.

016-724 ERROR — RAP Complex Position Error of Staple and Punch.

016-726 ERROR — RAP PDL Auto Switch Fail.

016-728 ERROR — RAP Unsupported TIFF Data.

016-729 ERROR — RAP TIFF Data Size too Big.

016-730 ERROR — RAP Unsupported ART Command.

016-731 ERROR — RAP Invalid TIFF Data.

016-732 ERROR — RAP Form Not Registered.

016-733 ERROR — RAP Destination Address Resolution Error.

016-734 ERROR — RAP Simple Transmission report invocation error.

016-735 ERROR — RAP Updating Job Template.

016-736 ERROR — RAP Remote directory lock error. Lock directory creation failed.

016-737 ERROR — RAP Remote lock directory remove error.

016-738 ERROR — RAP PS Booklet Print Output Paper Size is illegal.

016-739 ERROR — RAP Mismatch between PS Booklet Doc and Output Paper.

016-740 ERROR — RAP PS Booklet Output Tray is incorrect.

016-746 ERROR — RAP Unsupported PDF File.

016-748 ERROR — RAP HD Full.

016-749 ERROR — RAP JCL Syntax Error.

016-751 ERROR — RAP PDF Error.

016-752 ERROR — RAP PDF Short of Memory.

016-753 ERROR — RAP PDF Password Mismatched.

016-754 ERROR — RAP PDF LZW Not Installed.

016-755 ERROR — RAP PDF Print Prohibited.

016-756 ERROR — RAP Auditron-Prohibit Service.

016-757 ERROR — RAP Auditron-Invalid User.

016-758 ERROR — RAP Auditron-Disabled Function.

016-759 ERROR — RAP Auditron-Reached Limit.

016-760 ERROR — RAP PS Decompose Failure.

016-761 ERROR — RAP FIFO Empty.

016-762 ERROR — RAP Print LANG Not Installed.

016-764 ERROR — RAP SMTP Server Connect Error.

016-765 ERROR — RAP SMTP Server HD Full.

016-766 ERROR — RAP SMTP Server File System Error.

016-767 ERROR — RAP Invalid E-mail Address.

016-768 ERROR — RAP Invalid Sender Address.

016-769 ERROR — RAP SMTP Server Unsupported DSN.

016-771 ERROR — RAP Scan Data Repository ERR.

016-772 ERROR — RAP Scan Data Repository ERR.

016-773 ERROR — RAP Invalid IP Address.

016-774 ERROR — RAP HD Full-Compression Convert.

016-775 ERROR — RAP HD Full-Image Convert.

016-776 ERROR — RAP Image Convert ERR.

016-777 ERROR — RAP HD Access ERR-Image Convert.

016-778 ERROR — RAP HD Full-Scan Image Convert.

016-779 ERROR — RAP Scan Image Conversion Error.

016-780 ERROR — RAP HD Access ERR-Image Convert.

016-781 ERROR — RAP Scan Server Connect ERR.

016-782 ERROR — RAP Scan Server Login ERR.

016-783 ERROR — RAP Invalid Server Path.

016-784 ERROR — RAP Server Write ERR.

016-785 ERROR — RAP Server HD Full.

016-786 ERROR — RAP HD Full-Scan Write ERR.

016-787 ERROR — RAP Invalid Server IP ADD.

016-788 ERROR — RAP Retrieve to Browser Failed.

016-789 ERROR — RAP HD Full-Job Memory.

016-791 ERROR — RAP File Retrieve Fail.

016-792 ERROR — RAP Specified Job Not Found.

016-793 ERROR — RAP MF I/O HD Full.

016-794 ERROR — RAP Media Reader: Media No Insert.

016-795 ERROR — RAP Media Reader: Format Error.

016-796 ERROR — RAP Document insert operation error.

016-797 ERROR — RAP Media Reader: Image File Read Error.

016-798 ERROR — RAP No Trust Marking Option.

016-799 ERROR — RAP Print Instruction Fail.

016-940 ERROR — RAP With Duplex Output selected, a size difference between side 1 and side 2 was detected.

016-941 ERROR — RAP With Booklet selected, mixed-in-size/orientation pages with images were detected.

016-942 ERROR — RAP After a duplexed page was deleted, a size difference between side 1 and side 2 was detected.

016-943 ERROR — RAP After a document or divider was inserted, a size difference between side 1 and side 2 was detected.

016-944 ERROR — RAP Documents were merged, including the cover with an image, or a document with a divider.

016-945 ERROR — RAP A document unavailable for duplex print was inserted after a document available for Duplex was inserted.

016-946 ERROR — RAP A document or a divider was inserted after the cover or divider page.

016-949 ERROR — RAP The user inserted a documnet different in size/orientation from the page to be processed.

016-981 ERROR — RAP A failure in access to HDD.

016-982 ERROR — RAP HDD Access Error 2.

016-985 ERROR — RAP Data Size Over Flow (Scan to Email).

024-340 ERROR — RAP IOT-ESS Communication Failure 1.

024-341 ERROR — RAP IOT-ESS Communication Failure 2.

024-342 ERROR — RAP IOT-ESS Communication Failure 3.

024-343 ERROR — RAP IOT-ESS Communication Failure 4.

024-345 ERROR — RAP IOT-ESS Communication Failure 5.

024-346 ERROR — RAP IOT-ESS Communication Failure 6.

024-347 ERROR — RAP IOT-ESS Communication Failure 7.

024-348 ERROR — RAP IOT-ESS Communication Failure 8.

024-349 ERROR — RAP IOT-ESS Communication Failure 9.

024-350 ERROR — RAP IOT-ESS Communication Failure 10.

024-351 ERROR — RAP IOT-ESS Communication Failure 11.

024-352 ERROR — RAP IOT-ESS Communication Failure 12.

024-353 ERROR — RAP IOT-ESS Communication Failure 13.

024-354 ERROR — RAP IOT-ESS Communication Failure 14.

024-355 ERROR — RAP IOT-ESS Communication Failure 15.

024-356 ERROR — RAP IOT-ESS Communication Failure 16.

024-357 ERROR — RAP IOT-ESS Communication Failure 17.

024-358 ERROR — RAP IOT-ESS Communication Failure 18.

024-359 ERROR — RAP IOT-ESS Communication Failure 19.

024-360 ERROR — RAP IOT-ESS Initialization Failure.

024-361 ERROR — RAP Invalid IOT PaperSizeGroup Information.

024-362 ERROR — RAP Page Sync Illegal Start.

024-363 ERROR — RAP Page Sync Illegal Stop.

024-364 ERROR — RAP DMA Transfer Failure.

024-365 ERROR — RAP Overflow on the Loop Back Write.

024-366 ERROR — RAP JBIG Library Other Failure.

024-367 ERROR — RAP Decompress Other Failure.

024-368 ERROR — RAP PCI Error.

024-370 ERROR — RAP Marker Code Detect Failure.

024-371 ERROR — RAP IOT-ESS Communication Failure 21.

024-372 ERROR — RAP IOT-ESS Communication Failure 22.

024-373 ERROR — RAP IOT-ESS Communication Failure 23.

024-374 ERROR — RAP Regi Con PLL Parameter Failure.

024-375 ERROR — RAP IOT-ESS Communication Failure 24.

024-600 ERROR — RAP Billing master counter repair.

024-601 ERROR — RAP Billing backup counter #1 repair.

024-602 ERROR — RAP Billing backup counter #2 repair.

024-603 ERROR — RAP SWKey master counter repair.

024-604 ERROR — RAP SWKey backup counter #1 repair.

024-605 ERROR — RAP SWKey backup counter #2 repair.

024-606 ERROR — RAP Production Number/Serial Number Failure.

024-746 ERROR — RAP Selected Paper Tray Parameter Mismatch.

024-747 ERROR — RAP Print Instruction Failure.

024-910 ERROR — RAP Tray 1 Size Mismatch.

024-911 ERROR — RAP Tray 2 Size Mismatch.

024-912 ERROR — RAP Tray 3 Size Mismatch.

024-913 ERROR — RAP Tray 4 Size Mismatch.

024-914 ERROR — RAP Tray 6 Size Mismatch.

024-915 ERROR — RAP Tray 7 Size Mismatch.

024-917 ERROR — RAP Stacker Tray Staple Set Over Count.

024-919 ERROR — RAP Face UP Tray Close.

024-920 ERROR — RAP Face Down Tray 1 Paper FULL.

024-922 ERROR — RAP Face Down Tray 2 Paper FULL.

024-923 ERROR — RAP Operation Yellow Toner Empty.

024-924 ERROR — RAP Operation Magenta Toner Empty.

024-925 ERROR — RAP Operation Cyan Toner Empty.

024-926 ERROR — RAP Punch Dust Box Missing Set.

024-927 ERROR — RAP Offset Catch Tray Full Stack.

024-930 ERROR — RAP Stacker Tray Full (Small Size Full).

024-934 ERROR — RAP Paper type mismatch.

024-935 ERROR — RAP Tray 1 Paper Mismatch.

024-936 ERROR — RAP Tray 2 Paper Mismatch.

024-937 ERROR — RAP Tray 3 Paper Mismatch.

024-938 ERROR — RAP OHP kind Mismatch at Tray 4 (Not White Frame OHP).

024-939 ERROR — RAP Transparency type mismatch (No white border).

024-940 ERROR — RAP Folder Tray Out of Place.

024-941 ERROR — RAP Folder Tray Full Stack.

024-942 ERROR — RAP Booklet Sheets Over Count.

024-943 ERROR — RAP Booklet Low Staple.

024-945 ERROR — RAP Booklet Full Stack.

024-946 ERROR — RAP Tray 1 Not In Position.

024-947 ERROR — RAP Tray 2 Not In Position.

024-948 ERROR — RAP Tray 3 Not In Position.

024-949 ERROR — RAP Tray 4 Not In Position.

024-950 ERROR — RAP Tray 1 No Paper.

024-951 ERROR — RAP Tray 2 No Paper.

024-952 ERROR — RAP Tray 3 No Paper.

024-953 ERROR — RAP Tray 4 No Paper.

024-954 ERROR — RAP MSI No Paper.

024-955 ERROR — RAP Tray 6 No Paper.

024-956 ERROR — RAP Tray 7 No Paper.

024-957 ERROR — RAP Interposer No Paper.

024-958 ERROR — RAP MSI Size Mismatch.

024-959 ERROR — RAP Tray 1 Paper Size Mismatch.

024-960 ERROR — RAP Tray 2 Paper Size Mismatch.

024-961 ERROR — RAP Tray 3 Paper Size Mismatch.

024-962 ERROR — RAP Tray 4 Paper Size Mismatch.

024-965 ERROR — RAP ATS/APS No Paper.

024-966 ERROR — RAP ATS/APS No Destination Error.

024-967 ERROR — RAP Different Width Mix Paper Detect (Staple Job).

024-968 ERROR — RAP Stapler/Punch Batting.

024-969 ERROR — RAP Different Width Mix Punch.

024-970 ERROR — RAP Tray 6 Not In Position.

024-971 ERROR — RAP Tray 7 Not In Position.

024-972 ERROR — RAP Tray 6 Paper Size Mismatch.

024-973 ERROR — RAP Tray 7 Paper Size Mismatch.

024-974 ERROR — RAP Interposer Tray Size Mismatch.

Purpose

To show the status of input components e.g. sensors, and to run or energize output components e.g. motors, solenoids.

Description

Output and input component codes are entered into the Component Control Table on the UI, and then checked individually or in permitted groups. The codes in the tables are grouped in function chain order. Refer to GP 2 Fault Codes and History Files.

NOTE: To check the operation of the fuser temperature, tray size sensing, development housing ATC sensors and MOB sensor, refer to dC140 Analog Monitor.

Go to the appropriate procedure:

• Input Components
• Output Components

Input Components

When the appropriate code is entered, the status of the component is shown on the UI.

NOTE: The logic level shown on the BSD with the signal name is the actual signal as measured with a service meter. This is not necessarily the same as the logic state shown on the UI, especially where the output is inverted. When testing components using these control codes, look for a change in state, not for a high or low.

The displayed status of the input component can be changed by causing the component status to change, e.g. operating a sensor with a sheet of paper.

Go to the appropriate table:

• Table 1 Input codes 005.
• Table 2 Input Codes 012 — Integrated Office Finisher.
• Table 3 Input Codes 012 and 013 — Office Finisher LX.
• Table 4 Input codes 042.
• Table 5 Input Codes 062.
• Table 6 Input Codes 071 to 078.
• Table 7 Input Codes 091.

Output Components

When the appropriate code is entered, the component runs or energizes for a set time. The default timeout for most components is set at 90 seconds, but can be as short as 5 seconds. Some components require that other components are run or energized at the same time. It is possible to enter and run or energize up to 6 component control codes (not fax), but only in permitted groups. If illegal combinations of codes are entered, the components do not run or energize.

Go to the appropriate table:

• Table 8 Output Codes 005.
• Table 9 Output Codes 012 — Integrated Office Finisher.
• Table 10 Output Codes 012 and 013 — Office Finisher LX.
• Table 11 Output Codes 042.
• Table 12 Output Codes 061 and 062.
• Table 13 Output Codes 071 to 078.
• Table 14 Output Codes 091 to 094.

Procedure

1. Enter Diagnostics, GP 1.
2. Touch dC330 Component Control.

CAUTION: Check the component control tables for components that will damage the machine if run together.

3. Touch Chain-Link.
4. Enter the relevant Chain-Link number.
5. Touch OK.
6. Touch Start. The component will operate and the screen will display the information that follows:

• Chain-Link number of the component.
• Input or output code clarification.
• The component status.
• Operation counter.

7. Toggle Cyclic Motion to repeat the operation.
8. Touch Stop All to stop component operation.
9. Touch Close to return to the Diagnostics screen.
10. Exit diagnostics, GP 1.

Input Codes

Table 1 Input codes 005

Code	Displayed Name	Description	General
005-102	Document Sensor	Document sensor (Q05-102)	High = document present
005-110	Regi Sensor	Registration sensor (Q05-110)	High = no document
005-206	CVT Pre Regi Sensor	Pre-registration sensor (Q05-206)	High = no document
005-211	CVT Invert Sensor	Invert sensor (Q05-211)	High = no document
005-212	CVT Feeder Cover Interlock Switch	CVT feeder cover sensor (Q05-212)	High = Cover closed
005-213	CVT DADF Interlock Switch	CVT DADF interlock switch (S05-213)	High = DADF lowered
005-215	CVT #1 Tray APS Sensor (CVT)	Tray APS sensor 1 (Q05-215)	High/Low
005-216	CVT #2 Tray APS Sensor (CVT)	Tray APS sensor 2 (Q05-216)	High/Low
005-217	CVT #3 Tray APS Sensor (CVT)	Tray APS sensor 3 (Q05-217)	High/Low
005-218	CVT APS No. 1 Sensor	APS sensor 1 (Q05-218)	Low = document present
005-219	CVT APS No. 2 Sensor	APS sensor 2 (Q05-219)	Low = document present
005-220	CVT APS No. 3 Sensor	APS sensor 3 (Q05-220)	Low = document present
005-221	CVT Tray Size SNR No. 1	Tray size sensor 1 (Q05-221)	Low = document present
005-222	CVT Tray Size SNR No. 2	Tray size sensor 2 (Q05-222)	Low = document present
005-224	Scan Start (CVT)	Scan count signal.	High = on
005-226	#2 Invert Sensor (PF1)	Invert sensor 2 (Q05-226)	Low = document present
005-234	Home Position SNR	Link home position sensor (Q05-234) for nip release	High = nip

Table 2 Input Codes 012 — Integrated Office Finisher

Code	Displayed Name	Description	General
012-111	IOT Exit Sensor	IOT exit sensor (Q12-111)	High/Low
012-140	Ent Sensor	Entry sensor (Q12-140)	High/Low
012-150	Compile Exit Sensor	Compiler exit sensor (Q12-150)	High/Low
012-220	Front Tamper Home Sensor	Front tamper home sensor (Q12-220)	High = home
012-221	Rear Tamper Home Sensor	Rear tamper home sensor (Q12-221)	High = home
012-242	Low Staple Sensor	Low staples sensor (Q12-242)	High = almost empty
012-243	Self Priming Sensor	Self priming sensor (Q12-243)	High = ready
012-244	Staple Home Sensor	Staple head home sensor (Q12-244)	High = staple head home
012-251	Set Clamp Home Sensor	Set clamp home sensor (Q12-251)	High = set clamp home
012-252	Eject Home Sensor	Ejector home sensor (Q12-252)	High = Ejector home
012-267	Stack Height Sensor	Stack height sensor (Q12-267)	High/Low
012-278	Stack Sensor1	Stack sensor 1 (Q12-278)	High/Low
012-279	Stack Sensor2	Stack sensor 2 (Q12-279)	High/Low
012-300	Top Cover Interlock	Top cover interlock switch (S12-302)	High/Low
012-302	Finisher Front Door SW	Font door interlock switch (S12-302)	High/Low

Table 3 Input Codes 012 and 013 — Office Finisher LX

Code	Displayed Name	Description	General
012-100	Transport Entrance Sensor	Transport entry sensor (Q12-100)	High/Low
012-110	Reg. Clutch on Detect	Registration clutch (CL12-110)	On/off
012-111	IOT Exit Sensor	IOT exit sensor (Q12-111)	High/Low
012-150	Compile Exit Sensor	Compiler exit sensor (Q12-150)	High/Low
012-151	Compiler Tray No Paper Sensor	Compiler tray no paper sensor (Q12-151)	High/Low
012-190	H-Transport Entrance Sensor	H-transport entrance sensor (Q12-190)	High/Low
012-220	Front Tamper Home Sensor	Front tamper home sensor (Q12-220)	High = home
012-221	Rear Tamper Home Sensor	Rear tamper home sensor (Q12-221)	High = home
012-241	Stapler Move Position Sensor	Stapler move position sensor (Q12-241)	High/Low
012-242	Low Staple Sensor	Low staples sensor (Q12-242)	High = almost empty
012-243	Self Priming Sensor	Self priming sensor (Q12-243)	High = ready
012-244	Staple Home Sensor	Staple head home sensor (Q12-244)	High = staple head home
012-250	Eject Clamp Home Sensor	Eject clamp home sensor (Q12-250)	High/Low
012-251	Set Clamp Home Sensor	Set clamp home sensor (Q12-251)	High = set clamp home
012-260	Upper Limit Sensor	Upper limit sensor (Q12-260)	High/Low
012-262	Stacker Paper Sensor	Stacker paper sensor (Q12-262)	High/Low
012-263	Stacker Encoder Sensor	Stacker encoder sensor (Q12-263)	High/Low
012-264	Stack Height Sensor 1	Stack height sensor 1 (Q12-264)	High/Low
012-265	Stack Height Sensor 2	Stack height sensor 2 (Q12-265)	High/Low
012-271	Punch Home Sensor	Punch home sensor (Q12-271)	High/Low
012-274	Punch Encoder Sensor	Punch encoder sensor (Q12-274)	High/Low
012-275	Punch Box Set Sensor	Punch box set sensor (Q12-275)	High/Low
012-277	Puncher Detect	Puncher detect (Q12-277)	High/Low
012-300	Eject Cover Switch	Eject cover switch (S12-300)	High/Low
012-302	Fin. Front Door Intlk Switch	Finisher front door interlock switch (S12-302)	High/Low
012-303	H-Transport Open Sensor	H-transport open sensor (Q12-303)	High/Low
013-101	Folder Home Sensor	Folder home sensor (Q13-101)	High/Low
013-107	Booklet Front Low Staple Switch	Booklet front low staple switch (S13-107)	High = Staple slow
013-108	Booklet Rear Low Staple Switch	Booklet rear low staple switch (S13-108)	High = Staple slow
013-141	Booklet Front Staple Home Switch	Booklet front staple home switch (S13-141)	High/Low
013-142	Booklet Rear Staple Home Switch	Booklet rear staple home switch (S12-142)	High/Low
013-143	Booklet Stapler Move Position Sensor	Booklet stapler move position sensor (S13-143)	High/Low
013-144	Booklet Stapler Move Home Sensor	Booklet stapler move home sensor (S13-144)	High/Low
013-160	Folder Detect	Folder detect	High/Low
013-161	Booklet Detect	Booklet detect	High/Low
013-300	Booklet Cover Open Switch	Booklet cover open switch (S13-300)	High/Low
013-301	Booklet Safety Switch	Booklet safety switches	High/Low

Table 4 Input codes 042

Code	Displayed Name	Description	General
042-200	YMC Link Sensor	YMC link sensor (Q42-200)	High/Low
042-250	Fusing Exhaust Fan Fail	Detects using exhaust fan fail.	—
042-251	Marking Fan FAIL	Detects marking fan fail.	—

Table 5 Input codes 062

Code	Displayed Name	Description	General
062-212	IIT Regi Sensor	Scanner registration sensor (Q62-212)	Low = Actuated
062-240	ADF Exist	DADF present sensor (Q62-240)	High = DADF present
062-251	APS Sensor1	APS sensor 1 (Q62-251)	High = document present
062-253	APS Sensor3	APS sensor 3(Q62-253)	High = document present
062-300	Platen I/L Switch	Platen I/L sensor (Q62-300)	Low = DADF closed
062-301	Angle Sensor	Angle sensor (Q62-301)	Low = DADF closed

Table 6 Input codes 071 to 078

Code	Displayed Name	Description	General
071-101	#1 No Paper Sensor	Tray 1 no paper sensor (Q71-101)	High = Paper empty
071-102	#1 Level Sensor	Tray 1 level sensor (Q71-102)	High = top of stack sensed
071-104	#1 Tray Paper Size Switch	Tray 1 paper size switch (S71-104)	High = Tray out
071-105	#1 Pre Feed Sensor	Tray 1 pre feed sensor (Q71-105)	High = paper detected
072-101	#2 No Paper Sensor	Tray 2 no paper sensor (Q72-101)	High = Paper empty
072-102	#2 Level Sensor	Tray 2 level sensor (Q72-102)	High = top of stack sensed
072-103	#2 Feed Out Sensor	Tray 2 feed out sensor (Q72-103)	High = Paper Detected
072-104	#2 Tray Paper Size Sensor	Digital Tray 2 paper size sensor (Q72-104)	—
073-101	#3 No Paper Sensor	Tray 3 no paper sensor (Q73-101)	High = Paper empty
073-102	#3 Level Sensor	Tray 3 level sensor (Q73-102)	High = top of stack sensed
073-103	#3 Feed Out Sensor	Tray 3 feed out sensor (Q73-103)	High = Paper Detected
073-104	#3 Tray Paper Size Sensor	Digital Tray 3 paper size sensor (Q73-104)	—
074-101	#4 No Paper Sensor	Tray 4 no paper sensor (Q74-101)	High = Paper empty
074-102	#4 Level Sensor	Tray 4 level sensor (Q74-102)	High = top of stack sensed
074-103	#4 Feed Out Sensor	Tray 4 feed out sensor (Q74-103)	High = Paper Detected
074-104	#4 Tray Paper Size Sensor Digital	Tray 4 paper size sensor (Q74-104)	High/Low
075-100	MSI No Paper Sensor	Bypass tray no paper sensor (Q75-100)	High = Paper detected
077-100	#2 Exit Sensor	Exit 2 sensor (Q77-100)	High = paper detected
077-101	#1 Exit Sensor	Exit 1 sensor (Q77-101)	High = paper detected
077-104	Regi Sensor	Registration sensor (Q77-104)	High = paper detected
077-105	#2 Feed Out Sensor	#2 Feed Out Sensor	High = paper detected
077-120	IOT Feed Ready Signal Input	Feed ready signal	On/off
077-121	Tray Module Regi Stop Signal Input	Registration stop signal.	On/off
077-123	Tray Module Feed ON Signal Input	Feed on signal.	On/off
077-124	#1 OCT Full Stack Sensor	Exit 1 OCT full stack sensor (Q77-124)	High/Low
077-300	Left Hand Interlock Switch	Left hand interlock switch (S77-300)	High/Low
077-302	Left Hand High Cover Switch	Left hand high cover switch (S77-302)	High/Low
077-303	Front Interlock Switch	Front interlock switch (S77-303)	High/Low
077-306	Tray Module Left Hand Interlock Switch	TM left hand interlock switch (S77-306)	High = cover closed
078-100	HCF1 Pre Feed Sensor	HCF pre feed sensor (Q78-100)	High/Low
078-101	HCF1 Feed Out Sensor	HCF feed out sensor (Q78-101)	High/Low
078-200	HCF1 No Paper Sensor	HCF no paper sensor (Q78-200)	High/Low
078-201	HCF1 Level Sensor	HCF level sensor (Q78-201)	High/Low
078-202	HCF1 Size Sensor A	HCF size sensor A (Q78-202)	High/Low
078-203	HCF1 Size Sensor B	HCF size sensor B (Q78-203)	High/Low
078-204	HCF1 Tray In Sensor	HCF tray in sensor (Q78-204)	High/Low
078-300	HCF1 Transport Interlock	HCF transport interlock(S78-300)	High/Low
078-301	HCF1 Side Out Switch	HCF side out switch (S78-301)	High/Low

Table 7 Input codes 091

Code	Displayed Name	Description	General
091-200	Waste Toner Full Sensor	Detects toner waste bottle near full.	—

Output Codes

Table 8 Output Codes 005

Code	Displayed Name	Description	General
005-004	Feed Motor (CCW) 82.5mm/s	Runs the DADF feed motor (MOT05-004) counter clockwise at 82.5mm/s. 50 seconds timeout.	On/off
005-005	Feed Motor (CCW) 110.0mm/s	Runs the DADF feed motor (MOT05-004) counter clockwise at 110mm/s. 50 seconds timeout.	On/off
005-008	Feed Motor (CCW) 165.0mm/s	Runs the DADF feed motor (MOT05-004) counter clockwise at 165mm/s. 50 seconds timeout.	On/off
005-009	Feed Motor (CW) 330.0mm/s	Runs the DADF feed motor (MOT05-004) clockwise at 330mm/s. 50 second timeout.	On/off
005-010	Feed Motor (CCW) 220.0mm/s	Runs the DADF feed motor (MOT05-004) counter clockwise at 220mm/s. 50 second timeout.	On/off
005-013	Feed Motor (CW) 440.0mm/s	Runs the DADF feed motor (MOT05-004) clockwise at 440mm/s. 50 second timeout.	On/off
005-015	Feed Motor (CCW) 330.0mm/s	Runs the DADF feed motor (MOT05-004) counter clockwise at 330mm/s. 50 second timeout.	On/off
005-047	Feed Motor (CW) 110.0mm/s	Runs the DADF feed motor (MOT05-004) clockwise at 110mm/s. 50 second timeout.	On/off
005-048	Feed Motor (CW) 165.0mm/s	Runs the DADF feed motor (MOT05-004) clockwise at 165mm/s. 50 second timeout.	On/off
005-049	Feed Motor (CW) 220.0mm/s	Runs the DADF feed motor (MOT05-004) clockwise at 220mm/s. 50 second timeout.	On/off
005-062	DADF Feed Clutch	Energises the DADF feed clutch (CL05-062). 50 second timeout.	On/off
005-072	Nip Release Solenoid	Nip release solenoid (SOL05-072). 3 second timeout.	On/off
005-083	Doc Ready	Switches on the document ready signal.	On/off
005-088	Image Area	Image area.	On/off
005-098	Takeaway Clutch	Energises the DADF takeaway clutch (CL05-098). 50 second timeout.	On/off

Table 9 Output Codes 012 — Integrated Office Finisher

Code	Displayed Name	Description	General
012-013	Sub Paddle Solenoid	Energizes the sub paddle solenoid (SOL12-013). CAUTION: Do not run with 012-014. Running these codes at the same time can cause damage to the machine.	On/off. 660ms timeout.
012-014	Sub Paddle Rotation	Simultaneously runs the transport motor (MOT12-095) and energizes the paddle solenoid (SOL12-013) to rotate the sub paddle once. CAUTION: Do not run with 012-013, 012-095, 012-096 or 012-097. Running these codes at the same time can cause damage to the machine.	On/off. 660ms timeout.
012-017	Set Clamp Motor	Runs the set clamp motor (MOT12-017). CAUTION: Do not run with 012-061. Running these codes at the same time can cause damage to the machine.	On/off. 250 pulses.
012-020	Front Tamper Mot Low Front	Runs the front tamper motor (MOT12-020) at low speed to move the front tamper forward.	On/off. 100 pulses.
012-021	Front Tamper Mot Middle Front	Runs the front tamper motor (MOT12-020) at mid speed to move the front tamper forward.	On/off. 100 pulses
012-022	Front Tamper Mot High Front	Runs the front tamper motor (MOT12-020) at high speed to move the front tamper forward.	On/off. 100 pulses
012-023	Front Tamper Mot Low Rear	Runs the front tamper motor (MOT12-020) at low speed to move the front tamper backward.	On/off. 100 pulses
012-024	Front Tamper Mot Middle Rear	Runs the front tamper motor (MOT12-020) at mid speed to move the front tamper backward.	On/off. 100 pulses
012-025	Front Tamper Mot High Rear	Runs the front tamper motor (MOT12-020) at high speed to move the front tamper backward.	On/off. 100 pulses
012-026	Rear Tamper Mot Low Front	Runs the rear tamper motor (MOT12-026) at low speed to move the rear tamper forward.	On/off. 100 pulses.
012-027	Rear Tamper Mot Middle Front	Runs the rear tamper motor (MOT12-026) at mid speed to move the rear tamper forward.	On/off. 100 pulses
012-028	Rear Tamper Mot High Front	Runs the rear tamper motor (MOT12-026) at high speed to move the rear tamper forward.	On/off. 100 pulses
012-029	Rear Tamper Mot Low Rear	Runs the rear tamper motor (MOT12-026) at low speed to move the rear tamper backward.	On/off. 100 pulses.
012-030	Rear Tamper Mot Middle Rear	Runs the rear tamper motor (MOT12-026) at mid speed to move the rear tamper backward.	On/off. 100 pulses
012-031	Rear Tamper Mot High Rear	Runs the rear tamper motor (MOT12-026) at high speed to move the rear tamper backward.	On/off. 100 pulses
012-046	Staple Motor FORWARD	Runs the staple motor (MOT12-046) forwards.	On/off.
012-047	Staple Motor REVERSE	Runs the staple motor (MOT12-046) in reverse.	On/off. 180ms timeout.
012-054	Eject Motor Low FORWARD	Runs the eject motor (MOT12-054) at low speed to move the ejector out.	On/off. 2000 pulses
012-055	Eject Motor High FORWARD	Runs the eject motor (MOT12-054) at high speed to move the ejector out.	On/off. 2000 pulses
012-056	Eject Motor Low REVERSE	Runs the eject motor (MOT12-054) at low speed to move the ejector home.	On/off. 2000 pulses
012-057	Eject Motor High REVERSE	Runs the eject motor (MOT12-054) at high speed to move the ejector home.	On/off. 2000 pulses
012-060	Stacker Motor UP	Runs the stacker motor (MOT12-060) to drive the stacker tray up.	On/Off. 80ms timeout.
012-061	Stacker Motor DOWN	Runs the stacker motor (MOT12-060) to drive the stacker tray down.	On/Off. 80ms timeout.
012-095	Transport Motor Low	Runs the transport motor (MOT12-095) forward at low speed (equal to full IOT speed).
012-096	Transport Motor Hi	Runs the transport motor (MOT12-095) forward at high speed (transport speed in finisher).
012-097	Transport Motor Half Speed	Runs the transport motor (MOT12-095) forward at half speed (equal to half IOT speed).
012-110	Registration Clutch ON	Energizes the registration clutch (CL12-110).

Table 10 Output Codes 012 and 013 — Office Finisher LX

Code	Displayed Name	Description	General
012-013	Sub Paddle Solenoid	Energizes the sub paddle solenoid (SOL12-013).	On/off. 250 ms
012-018	Transport Motor Reverse	Runs the transport motor (MOT12-018) in reverse.	On/off.
012-020	Front Tamper Mot Low Front	Runs the front tamper motor (MOT12-020) at low speed to move the front tamper forward.	On/off. 82 pulses
012-022	Front Tamper Mot High Front	Runs the front tamper motor (MOT12-020) at high speed to move the front tamper forward.	On/off. 82 pulses
012-023	Front Tamper Mot Low Rear	Runs the front tamper motor (MOT12-020) at low speed to move the front tamper backward.	On/off. 82 pulses
012-025	Front Tamper Mot High Rear	Runs the front tamper motor (MOT12-020) at high speed to move the front tamper backward.	On/off. 82 pulses
012-026	Rear Tamper Motor Low Front	Runs the rear tamper motor (MOT12-026) at low speed to move the rear tamper forward.	On/off. 82 pulses
012-028	Rear Tamper Motor High Front	Runs the rear tamper motor (MOT12-026) at high speed to move the front tamper forward.	On/off. 82 pulses
012-029	Rear Tamper Motor Low Rear	Runs the rear tamper motor (MOT12-026) at low speed to move the rear tamper backward.	On/off. 82 pulses
012-031	Rear Tamper Motor High Rear	Runs the rear tamper motor (MOT12-026) at high speed to move the rear tamper backward.	On/off. 82 pulses
012-032	H-Transport Motor 1	Runs the horizontal transport motor (MOT12-032) forward at highest speed.	On/off.
012-033	H-Transport Motor 2	Runs the horizontal transport motor (MOT12-032) forward at high speed.	On/off.
012-034	H-Transport Motor 3	Runs the horizontal transport motor (MOT12-032) forward at mid speed.	On/off.
012-035	H-Transport Motor 4	Runs the horizontal transport motor (MOT12-032) forward at low speed.	On/off.
012-036	Transport Motor 1	Runs the transport motor (MOT12-036) forward at high speed.	On/off.
012-037	Transport Motor 2	Runs the transport motor (MOT12-036) forward at mid speed.	On/off.
012-038	Transport Motor 3	Runs the transport motor (MOT12-036) forward at low speed.	On/off.
012-039	H-Transport Motor Reverse	Runs the horizontal transport motor (MOT12-032) in reverse.	On/off.
012-040	Stapler Move Motor Front Low	Runs the stapler move motor (MOT12-040) to move the stapler assembly to the front at low speed.	On/off.
012-042	Stapler Move Motor Front High	Runs the stapler move motor (MOT12-040) to move the stapler assembly to the front at high speed.	On/off.
012-043	Stapler Move Motor Rear Low	Runs the stapler move motor (MOT12-040) to move the stapler assembly to the rear at low speed.	On/off.
012-045	Stapler Move Motor Rear High	Runs the stapler move motor (MOT12-040) to move the stapler assembly to the rear at high speed.	On/off.
012-046	Staple Motor Forward	Runs the stapler motor (MOT12-046) forwards.	On/off.
012-047	Staple Motor Reverse	Runs the stapler motor (MOT12-046) in reverse.	On/off. 200ms timeout.
012-050	Set Clamp Clutch	Energizes the set clamp clutch (CL12-050).	On/off. 583 pulses.
012-052	Eject Clamp Up	Runs the eject motor (MOT12-054) in reverse at high speed to raise the eject clamp roll.	On/off. 200ms timeout.
012-053	Eject Clamp Down	Runs the eject motor (MOT12-054) in reverse at high speed to lower the eject clamp roll.	On/off. 46 pulses after home.
012-054	Eject Motor Forward Low	Runs the eject motor (12-054) forward at low speed.	On/off. 1136 pulses.
012-055	Eject Motor Forward High	Runs the eject motor (12-054) forward at high speed.	On/off. 1136 pulses.
012-060	Stacker Motor Up	Runs the stacker motor (MOT12-060) to drive the stacker tray up.	On/Off. 500ms timeout.
012-061	Stacker Motor Down	Runs the stacker motor (MOT12-060) to drive the stacker tray down.	On/Off. 500ms timeout.
012-074	Punch Motor Move Home	Runs the punch motor (MOT12-074) to drive the punch home.	On/off.
012-077	Punch (2 hole)	Runs the punch motor (MOT12-074) to drive 2 hole punch movement.	On/off.
012-078	Punch (3 hole)	Runs the punch motor (MOT12-074) to drive 3 hole punch movement.	On/off.
012-079	Punch (4 hole)	Runs the punch motor (MOT12-074) to drive 4 hole punch movement.	On/off.
013-022	Knife Motor Forward	Runs the knife motor (MOT13-022) forward.	On/off.
013-023	Knife Motor Reverse	Runs the knife motor (MOT13-022) in reverse.	On/off.
013-024	Booklet Front Stapler Motor Forward	Runs the front booklet staple motor (MOT13-024) forward.	On/off.
013-025	Booklet Front Stapler Motor Reverse	Runs the front booklet staple motor (MOT13-024) in reverse.	On/off.
013-026	Booklet Rear Stapler Motor Forward	Runs the rear booklet staple motor (MOT13-026) forward.	On/off.
013-027	Booklet Front Stapler Motor Reverse	Runs the rear booklet staple motor (MOT13-026) in reverse.	On/off.
013-028	Booklet Staple Move Motor In	Runs the booklet staple move motor (MOT13-028) to move booklet stapler to the I/B side.	On/off. 350 pulses
013-029	Booklet Staple Move Motor Out	Runs the booklet staple move motor (MOT13-028) to move booklet stapler to the O/B side.	On/off. 350 pulses

Table 11 Output Codes 042

Code	Displayed Name	Description	General
041-001	AllSub integrated mode	Drum, dispense, waste toner box auger and fuser exit 1 noise detection processing.	—
041-002	Drum abnormal sound detection mode	Drum abnormal sound detection processing.	—
041-003	Dispense noise detection mode	Dispense abnormal sound detection processing.	—
041-004	Waste toner box auger and fuser exit 1 noise detection mode	Waste toner box auger and fuser exit 1 noise detection processing.	—
042-001	Main Motor (175mm/s)	Runs the main motor (MOT42-001) at 175mm/s.	On/off
042-002	Main Motor (126mm/s)	Runs the main motor (MOT42-001) at 126mm/s.	On/off
042-003	Main Motor (63mm/s)	Runs the main motor (MOT42-001) at 63mm/s.	On/off
042-004	Sub Motor (175mm/s)	Runs the sub motor (MOT42-004) at 175mm/s.	On/off
042-005	Sub Motor (126mm/s)	Runs the sub motor (MOT42-004) at 126mm/s.	On/off
042-006	Sub Motor (63mm/s)	Runs the sub motor (MOT42-004) at 63mm/s.	On/off
042-007	Fusing Motor (175mm/s)	Runs the fusing motor (MOT42-007) at 175mm/s.	On/off
042-008	Fusing Motor (126mm/s)	Runs the fusing motor (MOT42-007) at 126mm/s.	On/off
042-009	Fusing Motor (63mm/s)	Runs the fusing unit drive motor (MOT42-007) at 63mm/s.	On/off
042-010	YMC Link Solenoid	Energizes the YMC link solenoid (SOL42-010)	On/off
042-011	1st BTR Initialize	Initialize the 1st BTR.	On/off
042-050	Fusing Unit Exhaust Fan High Speed Rotation	Runs the fuser exhaust fan (MOT42-050) at high speed.	On/off
042-051	Fusing Unit Exhaust Fan Low Speed Rotation	Runs the fuser exhaust fan (MOT42-050) at low speed.	On/off
042-052	Marking Fan High Speed Rotation	Runs the marking fan (MOT42-052) at high speed.	On/off
042-053	Marking Fan Low Speed Rotation	Runs the marking fan (MOT42-052) at low speed.	On/off

Table 12 Output Codes 061 and 062

Code	Displayed Name	Description	General
061-001	LPH forced ON (allsolid)	Switches on the print head assembly (all beta pattern).	On/off
061-002	LPH forced ON (Cin 50%)	Switches on the print head assembly (Cin 50%).	On/off
061-003	LPH forced ON (thyristor transfer)	Switches on the print head assembly (performs thyristor transfer only).	On/off
062-002	IIT Exposure Lamp	Switches on the exposure Lamp. 3 minute timeout.	On/off
062-005	IIT Scan Motor (Scan direction)	Runs the scan motor (MOT62-005) to drive the scan carriage 50mm (2 inches) in the scan direction.	—
062-006	IIT Scan Motor (Return direction)	Runs the scan motor (MOT62-005) to drive the scan carriage 50mm (2 inches) in the return direction.	—

Table 13 Output Codes 071 to 078

Code	Displayed Name	Description	General
071-001	#1 Feed Motor 1-2-phase Feed Direction	Runs the tray 1 feed/lift motor (MOT71-001) at paper feed speed in the feed direction.	On/off
071-002	#1 Feed Motor 2-phase Lift Up Direction	Runs the tray 1 feed/lift motor (MOT71-001) at tray lift speed in the lift direction.	On/off
072-001	#2 Feed Motor 2-phase (CW 2) Feed Direction	Runs the tray 2 feed/lift motor (MOT72-001) at paper feed speed in the feed direction (2 phase control).	On/off
072-002	#2 Feed Motor 2-phase (CCW 2) Lift Up Direction	Runs the tray 2 feed/lift motor (MOT72-001) at tray lift speed in the lift direction.	On/off
072-003	#2 Feed Motor 1-2-phase (CW 1-2) Feed Direction	Runs the tray 2 feed/lift motor (MOT72-001) at paper feed speed in the feed direction (1-2 phase control)	On/off
073-001	#3 Feed Motor 2-phase (CW 2) Feed Direction	Runs the tray 3 feed/lift motor (MOT73-001) at paper feed speed in the feed direction (2 phase control).	On/off
073-002	#3 Feed Motor 2-phase (CCW 2) Lift Up Direction	Runs the tray 3 feed/lift motor (MOT73-001) at paper feed speed in the feed direction (1-2 phase control)	On/off
073-003	#3 Feed Motor 1-2-phase (CW 1-2) Feed Direction	Runs the tray 3 feed/lift motor (MOT73-001) (1-2 phase control)	On/off
074-001	#4 Feed Motor 2-phase (CW 2) Feed Direction	Runs the tray 4 feed/lift motor (MOT74-001) at paper feed speed in the feed direction (2 phase control).	On/off
074-002	#4 Feed Motor 2-phase (CCW 2) Lift Up Direction	Runs the tray 4 feed/lift motor (MOT74-001) at tray lift speed in the lift direction.	On/off
074-003	#4 Feed Motor 1-2-phase (CW 1-2) Feed Direction	Runs the tray 4 feed/lift motor (MOT74 -001) at paper feed speed in the feed direction (1-2 phase control)	On/off
075-001	MSI Feed Clutch	Energizes the bypass tray feed clutch (CL75-001).	On/off
077-001	Takeaway Clutch	Energizes the takeaway clutch (CL077-001).	On/off
077-002	Regi Clutch	Energizes the registration clutch (CL77-002).	On/off
077-003	Duplex Clutch	Energizes the duplex clutch (CL77-003).	On/off
077-004	Exit Gate Solenoid	Energizes the exit gate solenoid (SOL77-004).	On/off
077-010	#1 Exit Offset Solenoid	Energizes the exit 1 offset solenoid (SOL77-010).	On/off
077-014	Exit 2 Drive Motor Forward Rotation	Runs the exit 2 drive motor (MOT77-014) forwards (output direction).	On/off
077-015	Exit 2 Drive Motor Reverse Rotation	Runs the exit 2 drive motor (MOT77-014) in reverse (intake direction).	On/off
077-030	TM Feed Ready Signal Output	Switches on the feed ready signal.	On/off
077-031	IOT Regi Stop Signal Output	Switches on the registration stop signal.	On/off
077-032	IOT Feed ON Signal Output	Switches on the feed on signal.	On/off
077-033	TM T/A Motor 1 Full Speed	Runs the TM T/A motor 1 (MOT77-033) at full speed.	On/off
077-034	TM T/A Motor 1 Half Speed	Runs the TM T/A motor 1 (MOT77-033) at half speed.	On/off
077-035	TM T/A Motor 2 Full Speed	Runs the TM T/A motor 2 (MOT77-035) at full speed.	On/off
077-036	TM T/A Motor 2 Half Speed	Runs the TM T/A motor 2 (MOT77-035) at half speed.	On/off
078-003	HCF1 Feed Motor -Feed Direction	Runs the HCF feed/lift motor (MOT78-003) in the feed direction.	On/off
078-004	HCF1 Feed Motor – Lift Up	Runs the HCF feed/lift motor (MOT78-003) in the lift direction.	On/off
078-093	HCF1 T/A Motor	Runs the HCF T/A motor (MOT78-093) at low speed.	On/off
078-094	HCF1 T/A Motor	Runs the HCF T/A motor (MOT78-093) at high speed.	On/off

Table 14 Output Codes 091 to 094

Code	Displayed Name	Description	General
091-001	BCR Y DC	Energizes the BCR DC Y bias voltage.	On/off
091-002	BCR M DC	Energizes the BCR DC M bias voltage.	On/off
091-003	BCR C DC	Energizes the BCR DC C bias voltage.	On/off
091-004	BCR K DC	Energizes the BCR DC K bias voltage.	On/off
092-001	R_RAD_COM_DA	Switches on or off the R-RAD LED.	On/off
092-002	ADC shutter open	Energizes the CTD shutter solenoid to open the ADC shutter.	150ms timeout.
092-003	ADC shutter Close	De-energizes the CTD shutter solenoid to close the ADC shutter.	150ms timeout.
093-001	DISPENSE MOTOR-Y	Runs the Y dispense motor (MOT93-001) at process speed.	On/off
093-002	DISPENSE MOTOR-M	Runs the M dispense motor (MOT93-002) at process speed.	On/off
093-003	DISPENSE MOTOR-C	Runs the C dispense motor (MOT93-003) at process speed.	On/off
093-004	DISPENSE MOTOR-K	Runs the K dispense motor (MOT93-004) at process speed.	On/off
093-005	DEVE BIAS-DC-YMC	Energizes the Dev. DC YMC bias voltage.	On/off
093-006	DEVE BIAS-DC-K	Energizes the Dev. DC K bias voltage.	On/off
093-007	DEVE BIAS-AC-YMC	Energizes the Dev. AC YMC bias voltage.	On/off
093-008	DEVE BIAS-AC-K	Energizes the Dev. AC K bias voltage.	On/off
093-009	DEVE CLUTCH-K	Energizes the developer clutch K.	On/Off. 2000ms timeout.
094-001	2nd BTR (-)	Energizes the 2nd BTR (-) bias.	On/off
094-002	2nd BTR (+)	Energizes the 2nd BTR (+) bias.	On/off
094-003	1st BTR YMC Contact	Brings the 1st BTR (YMC) into contact with the drum.	—
094-004	1st BTR YMC Retract	Retracts the 1st BTR (YMC) from the drum.	—

**This procedure is from Xerox Service Manual. All brand names and trademarks are their respective owner’s property.**

You may be also interested in below toner and drum chip (CRUM) for Xerox VersaLink C7020, C7025, C7030, C7000.

Toner Chip (For North America and West Europe Region):

• 106R03741 106R03744 106R03743 106R03742
• 106R03757 106R03760 106R03759 106R03758
• 106R03737 106R03740 106R03739 106R03738

Toner Chip (For South America and East Europe Region):

• 106R03749 106R03752 106R03751 106R03750
• 106R03745 106R03748 106R03747 106R03746
• 106R03765 106R03768 106R03767 106R03766

Toner Chip (For Metered Machine):

• 106R03733 106R03736 106R03735 106R03734

Drum Chip:

• 113R00780 113R00782